Errata Sheet This Errata Sheet contains corrections or changes

Errata Sheet This Errata Sheet contains corrections or changes
Errata Sheet
This Errata Sheet contains corrections or changes
made after the publication of this manual.
Date:
Product Family:
DL205
Revision and Date
4th Edition, Rev. B; February 2013
Manual Number
D2-USER-M
November 18, 2013
Changes to Chapter 2. Installation, Wiring and Specifications
Page 2-4. Safety Guidelines; Class 1, Division 2 Approval
Replace the entire existing sub-section with the following:
This equipment is suitable for use in Class 1, Zone 2, Division 2, groups A, B, C and D or non-hazardous locations only.
WARNING: Explosion Hazard! Substitution of components may impair suitability for Class 1, Division 2.
Do not disconnect equipment unless power has been switched off or area is known to be non-hazardous.
WARNING: Explosion Hazard! Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous.
WARNING: All models used with connector accessories must use R/C (ECBT2) mating plug for all applicable models. All mating plugs shall
have suitable ratings for device.
WARNING: This equipment is designed for use in Pollution Degree 2 environments (installed within an enclosure rated at least IP54).
WARNING: Transient suppression must be provided to prevent the rated voltage from being exceeded by 140%.
Pages 2-13. Base Wiring Guidelines; Base Wiring
Both the 12/24 VDC Base Terminal Strip and 125 VDC Base Terminal Strip drawings show a flat jumper installed between
G and LG. This is incorrect; neither base has an LG terminal, and they do not have a jumper installed from the factory.
Pages 2-40 and 2-41. I/O Modules Position, Wiring, and Specification; F2–16TD1(2)P, DC Output With Fault Protection
Remove the notes on both pages stating that these modules do not support Think & Do products. Think & Do 8.0 now
supports both of these modules.
In both specifications tables delete the “Maximum load current” and Maximum OFF current” rows shown and insert the
following four new rows in their place:
F2-16TD1P, F2-16TD2P Updated Specs
Minimum load current
Maximum load current
0.2 mA
0.25 A/point; 4A/common
Max leakage current
0.2 mA (load detect enabled);
0.3 mA disabled
Max inrush current
150 mA for 10 ms
Continued on next page.
Page 1 of 2
Errata Sheet
Changes to Chapter 4. System Design and Control
Page 4-28. Expanding DL205 I/O; Configuring the CPU’s Remote I/O Channel
Replace the wiring drawing shown with this one:
RXD–
0V
TXD+
TXD–
DL250–1 / DL260 CPU Port 2
Remote I/O Master
6
D2-RSSS
Remote I/O Slave
7
Cable: Use AutomationDirect L19954
(Belden 9842) or equivalent
9
120 ohms
Termination Resistor
TXD+ / RXD+
13
RXD+
10
(TXD, RXD are
twisted pair)
T
D2-RSSS
Remote I/O Slave
(end of chain)
Jumper
T
1
1
TXD– / RXD–
2
2
Signal GND
3
3
Internal 150 ohms
resistor not used
with 120 ohms cable
(use 2 grounds leads - twisted pair)
Replace the paragraph right after this wiring drawing with this paragraph:
The twisted/shielded pair connects to the DL250–1 or DL260 Port 2 as shown. A termination resistor must be added
externally to the CPU, as close as possible to the connector pins. Its purpose is to minimize electrical reflections that occur over
long cables. A termination resistor must be present at both physical ends of the network.
Add this Note at the bottom of the page, right after the existing note:
See the transient suppression for inductive loads information in Chapter 2 of this manual for further information on wiring practices.
Page 2 of 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising