Clay Paky A.leda B-EYE K10 User Guide

Clay Paky A.leda B-EYE K10 User Guide
ENGLISH
A.LEDA B-EYE K10 EASY
A.LEDA B-EYE K10
A.LEDA B-EYE K20
®
C61415
C61419
C61420
INSTRUCTION MANUAL
ARY
N
I
M
ELI
PR
INDEX
Page
Contents
2
Safety information
3
Unpacking and preparation
4
Installation and start-up
5
Control panel
7
Menu setting
15
Maintenance
17
Technical information
17
Cause and solution of problems
18
Channel functions
Congratulations on choosing a Clay Paky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Clay
Paky range, has been designed and made with total quality to
ensure excellent performance and best meet your expectations
and requirements.
Carefully read this instruction manual in its entirety and keep it
safe for future reference. It is essential to know the information
and comply with the instructions given in this manual to ensure
the fitting is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting
or to other property or persons deriving from installation, use and
maintenance that have not been carried out in conformity with this
instruction manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the
characteristics stated in this instruction manual at any time and
without prior notice.
1
SAFETY INFORMATION
• Installation
Make sure all parts for fixing the projector are in a good state of repair.
Make sure the point of anchorage is stable before positioning the projector.
The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if
the primary support system fails, the fitting falls as little as possible.
If the safety chain gets used, it needs to be replaced with a genuine spare.
LED
• Minimum distance of illuminated objects
The projector needs to be positioned so that the objects hit by the beam of light are at least 0.20
metres (8”) from the lens of the projector.
0.2
• Minimum distance from flammable materials
The projector must be positioned so that any flammable materials are at least 0.20 metres (8”) from
every point on the surface of the fitting.
• Mounting surfaces
It is permissible to mount the fitting on normally flammable surfaces.
• Maximum ambient temperature
Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).
IP20
• IP20 protection rating
The fitting is protected against penetration by solid bodies of over 12mm (0.47”) in diameter (first
digit 2), but not against dripping water, rain, splashes or jets of water (second digit 0).
• Protection against electrical shock
Connection must be made to a power supply system fitted with efficient earthing (Class I appliance
according to standard EN 60598-1).
It is, moreover, recommended to protect the supply lines of the projectors from indirect contact
and/or shorting to earth by using appropriately sized residual current devices.
• Connection to mains supply
Connection to the electricity mains must be carried out by a qualified electrical installer.
Check that the mains frequency and voltage correspond to those for which the projector is designed
as given on the electrical data label.
This label also gives the input power to which you need to refer to evaluate the maximum number
of fittings to connect to the electricity line, in order to avoid overloading.
tc 90°C
• Temperature of the external surface
The maximum temperature that can be reached on the external surface of the fitting, in a thermally
steady state, is 90°C (194°F).
• Maintenance
Before starting any maintenance work or cleaning the projector, cut off power from the mains
supply.
LiFePO4
Pb
Risk Group 2
• Battery
This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To preserve
the environment, please dispose the battery at the end of its life according to the regulation in force.
• Photobiological Safety
CAUTION. Possibly hazardous optical radiation emitted from this product. Do not stare at operating
lamp. May be harmful to the eyes.
The products to which this manual refers comply with the European Directives pursuant to:
• 2006/95/EC - Safety of electrical equipment supplied at low voltage (LVD)
• 2004/108/EC - Electromagnetic Compatibility (EMC)
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)
A.LEDA B-EYE
2
UNPACKING AND PREPARATION
1
IST009/001
2 x 183102/805
Packing contents - Fig. 1
2
UNLOCKED
LOCKED
90
°
PAN Mechanism Lock and Release (every 90°) - Fig. 2
A.LEDA B-EYE
3
°
90
°
90
°
90
INSTALLATION AND START-UP
3
Installing the projector - Fig. 3
The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.
WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request).
This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.
4
1
2
2
3
1
Connecting and disconnecting power cable - Fig. 4
A.LEDA B-EYE
4
CONTROL PANEL
5
Mains
Connecting to the mains supply - Fig. 5
6
DMX 512
5 PIN
5
4
3
1
2
SCREEN
SIGNAL
SIGNAL
DMX 512
3 PIN
SIGNAL
SCREEN
1
2
3
SIGNAL
Connecting to the control signal line (DMX) - Fig. 6
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female
connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the
shield braid and to pin 1 of the connectors.
7
Fixture ID
Dmx Address
2
1
Warning Message
7.5m
Switching on the projector - Fig. 7
Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:
Model
A.leda B-EYE
Firmware
Version X.X.X
Date - Hour
xxx (Fixture ID)
Dmx Address xxx
System errors
E: .........................
W: .........................
On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt move to the “Home” position (Pan 50% - Tilt 50%). The control panel
(Fig. 7) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions:
rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address and the Fixture ID address (if set).
During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status.
It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the
key will be cancelled.
F
Continue
A.LEDA B-EYE
5
➔
8
28
28
Reversal of the display - Fig. 8
To activate this function, press UP and DOWN keys simultaneously while the display is in the rest mode. This status will be memorised and
maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.
Setting the projector starting address
On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
The address can also be set with the projector switched off.
Setting the address: see pag. 8.
Setting the projector Fixture ID
On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255).
The Fixture ID address can be set with the projector switched off.
Setting the Fixture ID: see pag. 8.
B
C
Functions of the buttons - Using the menu
F
C
Confirms the displayed value, or activates the displayed function, or enters the successive
menu.
Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.
DOWN
B
Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu.
D
Return to the top level.
E
Commute from units, tens, hundreds, in the "Address", "Fixture ID" and "Calibration" menù.
UP
LEFT
RIGHT
USING THE MENU:
once – “Main Menu” appears on the display.
1) Press
2) Use the UP
and DOWN
keys to select the menu to be used:
• Setup (Setup Menu): To set the setting options.
• Option (Option Menu): To set the operating options
• Informations (Informations Menu): To read the counters, software version and other information.
• Manual Control (Manual control Menu): To trigger the test and manual control functions.
• Test (Test Menu): To check the proper functionning of effects
• Advanced (Advanced Menu): Access to the "Advanced menu" is recommended for a trained technical personnel.
To enable the "Advanced" see pag.13
3) Press
to display the first item in the selected menu.
4) Use the UP
and DOWN
keys to select the MENU items.
F
F
B
C
B
C
Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press
to momentarily activate the display and thus access the settings. Once the required operations have been carried out,
the display will switch off again after a wait time of 30 seconds.
F
A.LEDA B-EYE
6
MENU SETTING
1
2
Set Up
Dmx
Address
3
Option
Pan / Tilt
Invert
Pan
Information
Invert
Tilt
Channel
Mode
System
Errors
Fixture
Hours
Swap
Pan-Tilt
LED
Energy Tot
Fixture ID
Encoder
Pan-Tilt
Ethernet
Interface
System
Version
P/T Homing
mode
Option
Board
Diagnost.
Pan Home
Def Pos
Information
Silent
Mode
Manual
Control
Tilt Home
Def Pos
Dmx
Monitor
Standard
Fans
Monitor
Quiet
Test
Display
Advanced
Special
Functions
Network
params
Pan/Tilt
speed
Dimmer
curve
RGB
Gamma
Halogen
Mode
Setting
Default
Preset
User
Preset 1
User
Preset 2
User
Preset 3
4
5
Manual
Control
Reset
Channel
6
Test
Pan / Tilt
Colour
Advanced
Access code
1234
Upload
Aleda fw
All
Setup
Model
Calibration
Continue
A.LEDA B-EYE
7
➔
NOTE: On grey the default options
Set Up
Dmx
Address
SET UP MENU
DMX ADDRESS
NOTE: without the DMX signal the Address (XXX) flashing
Allows you to select the DMX ADDRESS.
1) Press
- the current DMX Adress appear on the display.
2) Use the UP
and DOWN
, RIGHT
keys to plan the DMX
Address.
3) Press
to confirm the selection or LEFT
to keep current settings.
Address xxx
F
B
C
E
D
F
Channel
Mode
CHANNEL MODE
Allows you to select a channel arrangement from the four available.
1) Press
- the current settings appear on the display.
2) Use the UP
and DOWN
keys to select one of the following
settings:
- Standard
- Shape
- Extended
- Extended RGBW
- Full
3) Press
to confirm the selection or LEFT
to keep current settings.
Standard
F
Shape
Extended
Extended
RGBW
C
F
Full
Fixture ID
B
D
FIXTURE ID
Allows you to select the FIXTURE ID.
1) Press
- the current Fixture ID appear on the display.
2) Use the UP
, DOWN
, RIGHT
keys to plan the Fixture ID.
3) Press
to confirm the selection or LEFT
to keep current settings.
Value xxx
F
B
F
C
D
ETHERNET INTERFACE
It lets you set the Ethernet settings to be attributed to the projector.
1) Premere
.
2) Use the UP
and DOWN
keys to select the “Ethernet Interface”
options to set:
Ethernet
Interface
F
B
C
Control Protocol
It lets you select the “Control Protocol” Art-net to assign according to the
control unit used:
1) Press
the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following settings:
- Disabled
- Art-net on IP 2
- Art-net on IP 10
3) Press
to confirm the selection or LEFT
to keep the current setting.
Control
Protocol
F
B
C
F
D
Repeat on DMX
It lets you enable the transmission of the Ethernet protocol by DMX signal
to all the connected projectors.
1) Press
the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following settings:
- Disabled: DMX transmission disabled.
- Enabled on primary: DMX transmission enabled.
3) Press
to confirm the selection or LEFT
to keep the current setting.
Repeat on
DMX
F
B
C
F
D
Universe
It lets you assign the “Universe” number to be assigned to a series of
projectors.
1) Press
– the current Universe address appears on the display.
2) Use the UP
, DOWN
, RIGHT
keys to set the Universe
address.
3) Press
to confirm the selection or LEFT
to keep the current
setting.
Universe
F
F
A.LEDA B-EYE
E
8
B
C
E
D
OPTIONS MENU
Option
Pan / Tilt
Invert
Pan
PAN / TILT
Invert pan
Used for reversing Pan movement.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
PAN inversion.
3) Press
to confirm the selection or LEFT
to keep current settings.
On
Off
F
B
C
F
Invert
Tilt
D
Invert tilt
Used for reversing tilt movement.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off) Tilt
inversion.
3) Press
to confirm the selection or LEFT
to keep current settings.
On
Off
F
B
C
F
Swap
Pan-Tilt
D
Swap Pan-Tilt
Used for swapping Pan and Tilt channels (as well as Pan fine and Tilt fine).
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
Pan and Tilt channel swap.
3) Press
to confirm the selection or LEFT
to keep current settings.
On
Off
F
B
C
F
Encoder
Pan-Tilt
D
Encoder Pan-Tilt
Used for enabling the Pan / Tilt encoders.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
Pan / Tilt encoders.
3) Press
to confirm the selection or LEFT
to keep current settings.
On
Off
F
B
C
F
P/T Homing
Mode
D
P/T Homing Mode
Lets you set the initial projector Reset mode.
1) Press
, the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following
settings:
Standard: Pan & Tilt are simultaneously reset.
Sequenced: Tilt is reset first followed by Pan.
3) Press
to confirm the selection or LEFT
to keep the current setting.
Standard
Sequenced
F
B
C
F
D
Pan Home Def Pos
Lets you assign the Pan channel “home” position at the end of Reset,
without a DMX input signal.
1) Press
, the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following
settings:
0 degree
90 degrees
180 degrees
270 degrees (default)
3) Press
to confirm the selection or LEFT
to keep the current setting.
Pan Home
Def Pos
F
B
C
F
D
Tilt Home Def Pos
Lets you assign the Tilt channel “home” position at the end of Reset,
without a DMX input signal.
1) Press
, the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following settings:
0%
12.5%
25%
50% (default)
75%
87.5%
100%
3) Press
to confirm the selection or LEFT
to keep the current setting.
Tilt Home
Def Pos
F
B
C
F
Silent
mode
SILENT MODE
It lets you select the “Silent Mode” from the two available.
1) Press
the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following settings:
Standard: Maximum speed and consequently maximum effects noise level.
Quiet: reduces the speed of some effects, thereby reducing their noise level.
3) Press
to confirm the selection or LEFT
to keep the current setting.
Standard
F
Quiet
F
A.LEDA B-EYE
D
9
B
C
D
Continue
➔
DISPLAY
Used for automatically reduce brightness on the display after about 30
seconds in idle.
- the current settings appear on the display (On or Off).
1) Press
and DOWN
keys to enable (On) or disable (Off)
2) Use the UP
the decreasing of display brightness.
to confirm the selection or LEFT
to keep current settings.
3) Press
On
Option
Display
Off
F
B
C
F
Special
Functions
D
SPECIAL FUNCTIONS
Pan / Tilt speed
Lets you select two different Pan and Tilt speeds.
- the current setting appears on the display.
1) Press
and DOWN
keys to select one of the following settings:
2) Use the UP
- Normal
- Fast
to confirm the selection or LEFT
to keep current settings.
3) Press
Pan / Tilt
speed
F
B
C
F
D
Dimmer Curve
Lets you select four different Dimmer channel curves.
- the current setting appears on the display.
1) Press
and DOWN
keys to select one of the following
2) Use the UP
settings:
- Curve 1
- Curve 2
- Curve 3
- Curve 4
to confirm the selection or LEFT
to keep current settings.
3) Press
Dimmer
Curve
F
B
C
F
D
RGB Gamma
Lets you select three different RGBW gamma curves.
- the current setting appears on the display.
1) Press
and DOWN
keys to select one of the following settings:
2) Use the UP
- Gamma 1.0
- Gamma 1.5
- Gamma 2.0
to confirm the selection or LEFT
to keep current settings.
3) Press
RGB
Gamma
F
B
C
F
D
Halogen Mode
Lets you select five different halogen lamp simulations.
- the current setting appears on the display.
1) Press
and DOWN
keys to select one of the following
2) Use the UP
settings:
- Halogen OFF
- Halogen Lamp 1
- Halogen Lamp 2
- Halogen Lamp 3
- Halogen Lamp 4
- Halogen Lamp 5
to confirm the selection or LEFT
to keep current settings.
3) Press
Halogen
Mode
F
B
C
F
Setting
Default
Preset
SETTING
Used to save 3 different settings of the items in the options menu and
relative submenus.
- “Default preset” appears on the display.
1) Press
and DOWN
keys to select one of the following
2) Use the UP
configurations:
- Default preset (*)
- User preset 1
- User preset 2
- User Preset 3
- “Load preset X” appears on the display.
3) Press
and DOWN
keys to select:
4) Use the UP
- Load preset X to recall a previously stored configuration.
- Save to preset X to store the current configuration.
a confirmation message (Are you sure?) appears on the display.
5) Select YES to confirm the selection or NO to keep the current setting
and return to the next higher level.
(*) DEFAULT PRESET
key and the LEFT
key simultaneously
By pressing the RIGHT
once entered in the "main menu" it is possible to quickly (short cut)
reset the default settings (DEFAULT PRESET).
Used for restoring default values on all options menu items and relevant
submenus.
Reset To
Dafault
Go Back
User
Preset 1
F
Load
Preset 1
Save To
Preset 1
User
Preset 2
F
Load
Preset 2
Save To
Preset 2
User
Preset 3
Load
Preset 3
B
C
B
C
E
Save To
Preset 3
A.LEDA B-EYE
D
10
D
F
1) Press
, a confirmation message (Are you sure?) appears on the display.
2) Select YES to confirm the selction or NO to keep current setting.
OPTION
DEFAULT
Invert Pan
Off
Invert Tilt
Off
Swap Pan-Tilt
Off
Encoder Pan-Tilt
On
P/T Homing Mode
Standard
Pan Home Def Pos
270 degrees
Tilt Home Def Pos
50%
Display
On
Silent Mode
Standard
P/T Speed
Fast
Dimmer Curve
Curve 1
RGB Gamma
Gamma 1.5
Halogen Mode
Halogen Off
INFORMATION MENU
Information
SYSTEM ERRORS
Shows a list of warnings and messages relevant to errors occurred since
the fixtures switching-on.
1) Pressing
you are allowed to reset the SYSTEM ERRORS list.
A confirmation message (Are you sure you want to clear error list ?)
appears on the display.
2) Select YES to reset the list or NO to go back.
System
Errors
F
Fixture
Hours
FIXTURE HOURS
Used for displaying projector operating hours (total and partial).
1) Press
- Hours total and partial appears on the display.
Total counter
Counts the number of projector working life hours (from manufacture to date).
Partial counter
Counts the number of partial projector working life hours since the last
reset to date.
2) Press
to reset partial projector working hours a confirmation
message (Are you sure?) appears on the display.
3) Select YES to reset partial projectors counter or NO to keep the current
setting and return to the top menu level.
Total XXX
Partial XXX
F
Reset...
F
LED ENERGY TOT
Lets you view total LED working hours.
1) Press
- to display total and partial Watts/hour:
Total
Total LED working hours from construction to date.
Partial
LED working hours from last reset to date.
2) Press
to reset the partial counter. A confirmation appears on the
screen (Are you sure?)
3) Select YES to reset the partial counter or NO to keep the current setting
and open the next menu level.
LED Energy
Tot
F
F
System
Version
Board
CPU brd
com.dev
0: PT-3f
1: Ld - Kxx
Revis.
x.x.x
x.x
x.x
x.x
Hw.rv.
x.x
Board
Diagnost.
Board
0:PT-3f
1: Ld - Kxx
Status
Good
Good
Err%
0.00
0.00
SYSTEM VERSION
Used for displaying the software and hardware version of each board
installed in the projector.
CPU brd (CPU board)
0: PT-3f (Scheda Pan / Tilt)
1: Ld - Kxx (Scheda LED)
x.x
x.x
BOARD DIAGNOSTIC
Used for displaying the status error of each board installed in the projector:
0: PT-3f (Scheda Pan / Tilt)
1: Ld - Kxx (Scheda LED)
Dmx
Monitor
Fans
Monitor
DMX MONITOR
Used for displaying the projector DMX channel level in bit (Val) and in
percentage (Perc).
Fan
PwrSp
Head
FANS MONITOR
Used for displaying the speed of each fan installed in the projector:
PwrSp (fan PSU)
Head (fan head)
Speed (RPM)
XXXX
XXXX
NETWORK PARAMS
Allows the "Network" parameters of the projector to be displayed or:
IP address: Internet Protocol address (two projectors must not have the
same IP address)
IP mask: 255.0.0.0
Mac address: Media Access Control: the projector’s Ethernet Address.
Network
params
A.LEDA B-EYE
11
Continue
➔
MANUAL CONTROL
Manual
Control
RESET
Used for resetting the projector.
1) Press
to reset the projectors, a confirmation message (Are you
sure ?) appears on the display.
2) Select YES to starting reset the fixture or NO to keep the current
setting and return to the top menu level.
No
Reset
Yes
F
CHANNEL
Used for setting channel levels from the projector control panel.
1) Press
- the first channel appears on the display.
2) Use the UP
and DOWN
keys to select the required channel:
3) Press
and use the UP
and DOWN
keys to select the
required DMX level (value between 0 and 255).
4) Press LEFT
to return to the top menu level.
Channel
F
B
F
D
C
B
C
TEST MENU
Test
TEST
Allows you to check the proper functioning of effects.
1) Press
to return to the top menu level.
2) Use the UP
and DOWN
keys to select the required test.
3) Press
to confirm the selection or LEFT
to keep current settings.
Test sequence:
Pan - Tilt effects (Pan & Tilt)
Colour effects (CMY / CTO / Colour wheel)
All effects
Pan-Tilt
Colour
All
F
B
F
C
D
ADVANCED MENU
Advanced
To enable the "Advanced Menu" set up the "Access code" (1234) using the
UP
, DOWN
, RIGHT
keys.
Press
- "Menu advanced" appears on the display
Code
1234
B
F
Upload
Aleda fw
Transfer the firmware on all
the connected fixtures ?
Are you sure ?
Yes/No
Setup
Model
Changing to a wrong model
may damage the fixture.
Are you sure ?
Yes/No
C
E
UP LOAD FIRMWARE
Allows you to transfer the firmware from 1 fixture to all the connected fixtures.
1) Press
, a confirmation message appears on the display.
2) Select YES to start the firmware loading or NO to keep the current setting and return to the top menu level
F
SETUP MODEL
Allows you to change the default model of projector.
1) Press
a confirmation message appears on the display.
2) Select YES to define the model of projector or NO to keep the current
setting and return to the top menu level.
F
CALIBRATION
Allows you to adjust effects from the control panel to obtain perfect uniformity between the projectors.
1) Press
- “channels” appears on the display.
2) Using the UP
and DOWN
keys, select the effect you wish to
regulate.
3) Press
and use the RIGHT
, UP
and DOWN
buttons to
make the adjustment by setting a value between 0 and 255.
4) Press
to confirm the selection or LEFT
to keep current settings and return to the top level.
Calibration
F
F
F
B
C
E
B
C
D
FACTORY DEFAULT
Allows you to restore default values of all channels (128).
1) Press
– a confirmation message appears on the display (Reset
calibration to factory default ?).
2) Select YES to reset calibration to factory default or NO to keep the
current setting and return to the top menu level.
F
A.LEDA B-EYE
12
9
WARNING:
no alcohol
CAUTION:
• To avoid damage to the internal parts of the fixture when the fixture is not working, is recommended to turn the head down
before turning the fixture off, so that the front lenses of the fixture are invested as little as possible from the sun.
• Set channel 20 (Zoom) to 255-bit before turning off the projector to facilitate the packaging of the projector.
• To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The
frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of
the working environment (air humidity, presence of dust, salinity, etc.).
It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following
operations:
- General cleaning of internal parts.
- Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Clay Paky.
- General visual check of the internal components, cabling, mechanical parts, etc.
- Electrical, photometric and functional checks; eventual repairs.
Cleaning the lenses
Only use neutral soap and water to clean the lenses, then dry it carefully with a soft, non-abrasive cloth. (WARNING: the use of alcohol or any other
detergent could damage the lenses).
A.LEDA B-EYE
13
10
1
2
6
3
4
5
Battery removal - Fig. 10
This product contains a rechargeable lead-acid battery. To preserve the environment, please dispose the battery at the end of its life according
to the regulation in force.
LiFePO4
A.LEDA B-EYE
14
MAINTENANCE
11
3
4
1
2
Opening the covers - Fig. 11
12
1
2
1
1
1
Removing/Assembling the lens unit - Fig. 12
A.LEDA B-EYE
15
13
Replacing the line actuator - Fig. 13
CAUSE AND SOLUTION OF PROBLEMS
THE PROJECTOR WILL NOT SWITCH ON
ELECTRONICS NON-OPERATIONAL
PROBLEMS
DEFECTIVE PROJECTION
REDUCED LUMINOSITY
POSSIBLE CAUSES
No mains supply.
LED exhausted or defective.
Signal transmission cable faulty or disconnected.
Incorrect addressing.
Fault in the electronic circuits.
Lenses or reflector broken
Dust or grease deposited.
A.LEDA B-EYE
CHECKS AND REMEDIES
Check the power supply voltage.
Call an authorised technician.
Replace the cables.
Check addresses (see instructions).
Call an authorised technician.
Call an authorised technician.
Clean (see instructions).
16
TECHNICAL INFORMATION
350
(13.78")
Zoom OUT
310
(12.20")
Zoom IN
Power supplies available
100-240V 50/60Hz
A.Leda B-EYE K10
233
(9.17")
Zoom OUT
189
(7.44")
Zoom IN
Input power
• K20 - 750VA
• K10 - 450VA
248
(9.76")
360
(14.17")
423
(16.65")
LED source
LED Osram Ostar RGBW - 15W
Average LED life: 50.000 h
Motors
5 (k10), 7 (k20) stepper motors, operating with microsteps,
totally microprocessor controlled.
Cooling
• High efficiency die-cast aluminium
• Forced ventilation
494
(19.45")
Inputs
DMX 512
358
(14.09")
253
(9.96")
Working position
Functioning in any position.
340
(13.39")
Zoom OUT
290
(11.42")
Zoom IN
Movable body
• Movement by means of two stepper motors, controlled
by microprocessor.
• Automatic repositioning of PAN and TILT after accidental
movement not controlled by control unit.
• Travel:
- PAN = 540°
- TILT = 210°
A.Leda B-EYE K10 easy
230
(9.06")
Zoom OUT
180
(7.09")
Zoom IN
248
(9.76")
360
(14.17")
423
(16.65")
CE Marking
Complies with the following European Directives
- 2006/95/EC (LVD)
- 2004/108/EC (EMC)
- 2011/65/EU (RoHS).
479
(18.86")
Weights
• K10: 14.5 kg
• K20: 21 kg
358
(14.09")
253
(9.96")
430
(16.93")
Zoom OUT
380
(14.96")
Zoom IN
A.Leda B-EYE K20
250
(9.84")
Zoom OUT
200
(7.87")
Zoom IN
370
(14.57")
460
(18.11")
476
(18.74")
589
(23.19")
330
(12.99")
A.LEDA B-EYE
IP20 protection rating
• Protected against the entry of solid bodies larger than
12mm (0.47”).
• No protection against the entry of liquids.
395
(15.55")
17
CHANNEL FUNCTION
A.LEDA B-EYE K10 EASY
STANDARD
SHAPES
EXTENDED
EXTENDED RGBW
FULL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL MODE
CHANNEL MODE
CHANNEL MODE
CHANNEL MODE
CHANNEL MODE
1
Red
1
Red
1
Red
1
Red
1
Red
2
Red fine
2
Red fine
2
Red fine
2
Red fine
2
Red fine
3
Green
3
Green
3
Green
3
Green
3
Green
4
Green fine
4
Green fine
4
Green fine
4
Green fine
4
Green fine
5
Blue
5
Blue
5
Blue
5
Blue
5
Blue
6
Blue fine
6
Blue fine
6
Blue fine
6
Blue fine
6
Blue fine
7
White
7
White
7
White
7
White
7
White
8
White fine
8
White fine
8
White fine
8
White fine
8
White fine
9
Linear CTO
9
Linear CTO
9
Linear CTO
9
Linear CTO
9
Linear CTO
10
Macro colour
10
Macro colour
10
Macro colour
10
Macro colour
10
Macro colour
11
Strobe
11
Strobe
11
Strobe
11
Strobe
11
Strobe
12
Dimmer
12
Dimmer
12
Dimmer
12
Dimmer
12
Dimmer
13
Dimmer Fine
13
Dimmer Fine
13
Dimmer Fine
13
Dimmer Fine
13
Dimmer Fine
14
Pan
14
Pan
14
Pan
14
Pan
14
Pan
15
Pan Fine
15
Pan Fine
15
Pan Fine
15
Pan Fine
15
Pan Fine
16
Tilt
16
Tilt
16
Tilt
16
Tilt
16
Tilt
17
Tilt Fine
17
Tilt Fine
17
Tilt Fine
17
Tilt Fine
17
Tilt Fine
18
Function
18
Function
18
Function
18
Function
18
Function
19
Reset
19
Reset
19
Reset
19
Reset
19
Reset
20
Zoom
20
Zoom
20
Zoom
20
Zoom
20
Zoom
21
Shape Selection
21
Red LED 1
21
Red LED 1
21
Shape Selection
22
Shape Speed
22
Green LED 1
22
Green LED 1
22
Shape Speed
23
Shape Fade
23
Blue LED 1
23
Blue LED 1
23
Shape Fade
24
Shape R
…
Red LED …
24
White LED 1
24
Shape R
25
Shape G
…
Green LED …
…
Red LED …
25
Shape G
26
Shape B
…
Blue LED …
…
Green LED …
26
Shape B
27
Shape W
75
Red LED 19
…
Blue LED …
27
Shape W
28
Shape Dimmer
76
Green LED 19
…
White LED …
28
Shape Dimmer
29
Background Dimmer
77
Blue LED 19
93
Red LED 19
29
Background Dimmer
30
Shape Transition
94
Green LED 19
30
Shape Transition
31
Shape Offset
95
Blue LED 19
31
Shape Offset
32
Foreground Strobe (reserved)
96
White LED 19
32
Foreground Strobe (reserved)
33
Background Strobe (reserved)
33
Background Strobe (reserved)
34
Background Select (reserved)
34
Background Select (reserved)
35
Red LED 1
36
Green LED 1
37
Blue LED 1
…
Red LED …
…
Green LED …
A.LEDA B-EYE
18
…
Blue LED …
89
Red LED 19
90
Green LED 19
91
Blue LED 19
A.LEDA B-EYE K10
STANDARD
SHAPES
EXTENDED
EXTENDED RGBW
FULL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL MODE
CHANNEL MODE
CHANNEL MODE
CHANNEL MODE
CHANNEL MODE
1
Red
1
Red
1
Red
1
Red
1
Red
2
Red fine
2
Red fine
2
Red fine
2
Red fine
2
Red fine
3
Green
3
Green
3
Green
3
Green
3
Green
4
Green fine
4
Green fine
4
Green fine
4
Green fine
4
Green fine
5
Blue
5
Blue
5
Blue
5
Blue
5
Blue
6
Blue fine
6
Blue fine
6
Blue fine
6
Blue fine
6
Blue fine
7
White
7
White
7
White
7
White
7
White
8
White fine
8
White fine
8
White fine
8
White fine
8
White fine
9
Linear CTO
9
Linear CTO
9
Linear CTO
9
Linear CTO
9
Linear CTO
10
Macro colour
10
Macro colour
10
Macro colour
10
Macro colour
10
Macro colour
11
Strobe
11
Strobe
11
Strobe
11
Strobe
11
Strobe
12
Dimmer
12
Dimmer
12
Dimmer
12
Dimmer
12
Dimmer
13
Dimmer Fine
13
Dimmer Fine
13
Dimmer Fine
13
Dimmer Fine
13
Dimmer Fine
14
Pan
14
Pan
14
Pan
14
Pan
14
Pan
15
Pan Fine
15
Pan Fine
15
Pan Fine
15
Pan Fine
15
Pan Fine
16
Tilt
16
Tilt
16
Tilt
16
Tilt
16
Tilt
17
Tilt Fine
17
Tilt Fine
17
Tilt Fine
17
Tilt Fine
17
Tilt Fine
18
Function
18
Function
18
Function
18
Function
18
Function
19
Reset
19
Reset
19
Reset
19
Reset
19
Reset
20
Zoom
20
Zoom
20
Zoom
20
Zoom
20
Zoom
21
Zoom Rotation
21
Zoom Rotation
21
Zoom Rotation
21
Zoom Rotation
21
Zoom Rotation
22
Shape Selection
22
Red LED 1
22
Red LED 1
22
Shape Selection
23
Shape Speed
23
Green LED 1
23
Green LED 1
23
Shape Speed
24
Shape Fade
24
Blue LED 1
24
Blue LED 1
24
Shape Fade
25
Shape R
…
Red LED …
25
White LED 1
25
Shape R
26
Shape G
…
Green LED …
…
Red LED …
26
Shape G
27
Shape B
…
Blue LED …
…
Green LED …
27
Shape B
28
Shape W
76
Red LED 19
…
Blue LED …
28
Shape W
29
Shape Dimmer
77
Green LED 19
…
White LED …
29
Shape Dimmer
30
Background Dimmer
78
Blue LED 19
90
Red LED 18
30
Background Dimmer
31
Shape Transition
91
Green LED 18
31
Shape Transition
32
Shape Offset
92
Blue LED 18
32
Shape Offset
33
Foreground Strobe (reserved)
93
White LED 18
33
Foreground Strobe (reserved)
34
Background Strobe (reserved)
94
Red LED 19
34
Background Strobe (reserved)
35
Background Select (reserved)
95
Green LED 19
35
Background Select (reserved)
96
Blue LED 19
36
Red LED 1
37
Green LED 1
38
Blue LED 1
…
Red LED …
…
Green LED …
…
Blue LED …
90
Red LED 19
91
Green LED 19
92
Blue LED 19
Continue
A.LEDA B-EYE
19
➔
A.LEDA B-EYE K20
STANDARD
SHAPES
EXTENDED
EXTENDED RGBW
FULL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL
CHANNEL MODE
CHANNEL MODE
CHANNEL MODE
CHANNEL MODE
CHANNEL MODE
1
Red
1
Red
1
Red
1
Red
1
Red
2
Red fine
2
Red fine
2
Red fine
2
Red fine
2
Red fine
3
Green
3
Green
3
Green
3
Green
3
Green
4
Green fine
4
Green fine
4
Green fine
4
Green fine
4
Green fine
5
Blue
5
Blue
5
Blue
5
Blue
5
Blue
6
Blue fine
6
Blue fine
6
Blue fine
6
Blue fine
6
Blue fine
7
White
7
White
7
White
7
White
7
White
8
White fine
8
White fine
8
White fine
8
White fine
8
White fine
9
Linear CTO
9
Linear CTO
9
Linear CTO
9
Linear CTO
9
Linear CTO
10
Macro colour
10
Macro colour
10
Macro colour
10
Macro colour
10
Macro colour
11
Strobe
11
Strobe
11
Strobe
11
Strobe
11
Strobe
12
Dimmer
12
Dimmer
12
Dimmer
12
Dimmer
12
Dimmer
13
Dimmer Fine
13
Dimmer Fine
13
Dimmer Fine
13
Dimmer Fine
13
Dimmer Fine
14
Pan
14
Pan
14
Pan
14
Pan
14
Pan
15
Pan Fine
15
Pan Fine
15
Pan Fine
15
Pan Fine
15
Pan Fine
16
Tilt
16
Tilt
16
Tilt
16
Tilt
16
Tilt
17
Tilt Fine
17
Tilt Fine
17
Tilt Fine
17
Tilt Fine
17
Tilt Fine
18
Function
18
Function
18
Function
18
Function
18
Function
19
Reset
19
Reset
19
Reset
19
Reset
19
Reset
20
Zoom
20
Zoom
20
Zoom
20
Zoom
20
Zoom
21
Zoom Rotation
21
Zoom Rotation
21
Zoom Rotation
21
Zoom Rotation
21
Zoom Rotation
22
Shape Selection
22
Red LED 1
22
Red LED 1
22
Shape Selection
23
Shape Speed
23
Green LED 1
23
Green LED 1
23
Shape Speed
24
Shape Fade
24
Blue LED 1
24
Blue LED 1
24
Shape Fade
25
Shape R
…
Red LED …
25
White LED 1
25
Shape R
26
Shape G
…
Green LED …
…
Red LED …
26
Shape G
27
Shape B
…
Blue LED …
…
Green LED …
27
Shape B
28
Shape W
130
Red LED 37
…
Blue LED …
28
Shape W
29
Shape Intensity
131
Green LED 37
…
White LED …
29
Shape Intensity
30
Background Intensity
132
Blue LED 37
166
Red LED 37
30
Background Intensity
31
Shape Transition
167
Green LED 37
31
Shape Transition
32
Shape Offset
168
Blue LED 37
32
Shape Offset
33
Foreground Strobe (reserved)
169
White LED 37
33
Foreground Strobe (reserved)
A.LEDA B-EYE
34
Background Strobe (reserved)
34
Background Strobe (reserved)
35
Background Select (reserved)
35
Background Select (reserved)
36
Red LED 1
37
Green LED 1
38
Blue LED 1
…
Red LED …
…
Green LED …
…
Blue LED …
144
Red LED 37
145
Green LED 37
146
Blue LED 37
20
NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 128 bit - Tilt 128 bit ) all the others channels stay at 0 bit.
• RED
GREEN
BLUE
WHITE
• MACRO COLOUR
255
0
• RED FINE
GREEN FINE
BLUE FINE
WHITE FINE
EFFECT
BIT
LED OFF
BIT
255
0
BIT
LED ON
EFFECT
UP
LOW
• LINEAR CTO
BIT
EFFECT
LEE
REFERENCE
COLOUR
BIT VALUE
R G B W
209-255
-
White
255
235
66
255
208
-
Dirty White
255
255
122
255
207
197
Alice Blue
128
255
143
0
191-206
181
Congo Blue
77
0
255
0
184-190
174
Dark Steel Blue
181
255
95
0
180-183
170
Deep lavender
255
168
64
0
179
169
Lilac Tint
255
199
49
0
175-178
165
Daylight Blue
82
214
90
0
174
164
Flame Red
255
46
2
0
172-173
162
Bastard Amber
255
181
28
0
168-171
158
Deep Orange
222
84
0
0
162-167
152
Pale Gold
253
171
26
0
157-161
147
Apricot
255
143
13
0
151-156
141
Bright Blue
0
255
87
0
149-150
139
Primary Green
77
255
0
0
147-148
137
Special lavender
219
197
79
0
146
136
Pale Lavender
255
197
61
0
145
135
Deep Golden Amber
255
58
0
0
142-144
132
Medium Blue
0
255
143
0
138-141
128
Bright Pink
255
53
36
0
136-137
126
Mauve
227
41
56
0
134-135
124
Dark Green
84
255
13
0
131-133
121
Leaf Green
206
255
0
0
129-130
119
Dark Blue
0
186
255
0
128
118
Light Blue
74
255
82
0
127
117
Steel Blue
206
255
56
0
126
116
Med Blu Green
206
255
56
0
125
115
Peacock Blue
51
255
51
0
123-124
113
Magenta
255
20
15
0
121-122
111
Dark Pink
255
109
33
0
120
110
Middle Rose
217
130
28
0
119
109
Light Salmon
255
138
31
0
118
108
English Rose
255
148
23
0
255
2500 K
117
107
Light Rose
255
141
31
0
…
…
115-116
105
Orange
255
122
0
0
224
3200 K
255
166
0
0
…
104
Deep Amber
…
114
113
103
Straw
230
160
0
69
188
4000 K
…
…
112
102
Light Amber
237
163
0
0
144
5000 K
110-111
100
Spring Yellow
245
202
0
0
…
…
117
5600 K
100-109
90
Dark yellow green
41
219
0
0
…
…
89-99
79
Just Blue
0
194
130
0
99
6000 K
78-88
68
Sky Blue
0
255
135
0
68-77
58
Lavender
243
117
133
199
…
…
54
7000 K
…
…
62-67
52
Light Lavender
243
117
39
197
10
8000 K
49-61
39
Pink Carnation
255
107
0
130
0-9
UNUSED RANGE
46-48
36
Medium Pink
255
87
0
107
45
35
Light Pink
255
112
0
141
35-44
25
Sunrise Red
255
83
2
0
32-34
22
Dark Amber
255
65
0
0
31
21
Gold Amber
255
100
0
0
30
20
Medium Amber
255
135
0
0
29
19
Fire
255
56
0
0
27-28
17
Surprise Peach
198
114
9
0
23-26
13
Straw Tint
152
115
9
0
20-22
10
Medium Yellow
156
126
0
0
19
-
Black
0
0
0
0
18
-
White 5000 K
255
137
0
193
17
-
White 3700 K
255
201
25
255
16
-
White 7000 K
216
237
61
255
15
-
Magenta
255
0
255
0
14
-
Yellow
255
255
0
0
13
-
Cyan
0
255
255
0
12
-
Blue
0
0
255
0
11
-
Green
0
255
0
0
10
-
Red
255
0
0
0
0-9
-
Macro color OFF
-
-
-
-
Note: If CTO channel is active, the WHITE channel is disabled.
Continue
A.LEDA B-EYE
21
➔
• STOP STROBE
• TILT
MACRO
BIT
EFFECT
252 - 255
239 - 251
226 - 238
213 - 225
208 - 212
207
OPEN
RANDOM FAST STROBE
RANDOM MEDIUM STROBE
RANDOM SLOW STROBE
OPEN
FAST PULSATION (25 flash/sec)
108
104 - 107
103
SLOW PULSATION (0,5 flash/sec)
OPEN
FAST STROBE (25 flash/sec)
4
0-3
• TILT FINE
BIT
BIT
255
255
0
0
SLOW STROBE (1 flash/sec)
CLOSED
G
Operation with option InvertPan Off
(Tilt conventionally represented at 35 bit and option Invert Tilt
• DIMMER
• DIMMER FINE
BIT
255
0
EFFECT
EFFECT
BIT
FULL LIGHT
255
NO LIGHT
0
GOff)
BIT
BIT
255
255
0
0
UP
LOW
G
Operation with option InvertPan On
(Tilt conventionally represented at 35 bit and option Invert Tilt
• PAN
• FUNCTION
• PAN FINE
BIT
BIT
BIT
255
255
0
EFFECT
103 – 255
98 – 102
Reserved
Halogen Lamp Simulation, type 5 (2500 W)
Linear CTO @ 0 bit
93 – 97
88 – 92
Halogen Lamp Simulation, type 4 (2000 W)
Halogen Lamp Simulation, type 3 (1200 W)
Linear CTO @ 0 bit
Linear CTO @ 0 bit
83 – 87
78 – 82
73 – 77
Halogen Lamp Simulation, type 2 (1000 W)
Halogen Lamp Simulation, type 1 (750W)
Halogen Lamp Simulation OFF (Default)
Linear CTO @ 0 bit
Linear CTO @ 0 bit
68 – 72
63 – 67
58 – 62
52 – 57
48 – 52
43 – 47
38 – 42
24 – 37
12 – 24
0 – 11
RGBW Gamma curve 3 – gamma = 2.0
RGBW Gamma curve 2 – gamma = 1.5
RGBW Gamma curve 1 – gamma = 1.0
Dimmer Curve 4
Dimmer Curve 3
Dimmer Curve 2
Dimmer Curve 1
Pan Tilt Normal
Pan Tilt Fast (Default)
Function off – rearmed
0
G
Operation with option InvertPan Off
(Tilt conventionally represented at 35 bit and option Invert Tilt
The functions are actived passing through the “unused range” and staying 5 seconds
in necessary level.
Last selected function still active. Enable setting a new function.
GOff)
BIT
BIT
255
255
0
0
G
Operation with option InvertPan On
(Tilt conventionally represented at 35 bit and option Invert Tilt
A.LEDA B-EYE
GOff)
GOff)
22
DIMMER CURVE 1 - GAMMA 1 LINEAR
DIMMER CURVE 3 - GAMMA 2,0
DIMMER CURVE 2 - GAMMA 1,5
DIMMER CURVE 4 - S
• RESET
BIT
255
• RED LED 1 to…
GREEN LED 1 to…
BLUE LED 1 to…
WHITE LED 1 to…
EFFECT
COMPLETE RESET
Complete reset is activated passing throug the unused range
and staying 5 seconds in complete reset levels
128
127
BIT
EFFECT
255
LED ON
0
LED OFF
COMPLETE RESET
PAN / TILT RESET
Pan / Tilt reset is activated passing throug the unused range
and staying 5 seconds in Pan / Tilt reset levels
77
76
PAN / TILT RESET
ZOOM RESET
Effects reset is activated passing throug the unused range
and staying 5 seconds in Effects reset levels.
26
25
0
ZOOM RESET
UNUSED RANGE
• ZOOM
BIT
255
0
EFFECT
WIDE BEAM
NARROW BEAM
• ZOOM ROTATION
BIT
STOP
EFFECT
255
FAST ROTATION
193
191 - 192
190
SLOW ROTATION
STOP
SLOW ROTATION
128
127
FAST ROTATION
LINEAR ROTATION
0
• ZOOM ROTATION (available on zoom channel from 0 bit to 42 bit)
BIT
193-255
191-192
128-190
127
126
….
3
2
1
0
MACRO EFFECT
CCW Rotation, speed from 3 RPH to 10 RPM
Stop rotation
CW Rotation, speed from 10 RPM to 3 RPH
Indexed zone. Lens angle = 60.00
Indexed zone. Lens angle = 59.52
Indexed zone. Lens angle = 1.42
Indexed zone. Lens angle = 0.94
Indexed zone. Lens angle = 0.47
Indexed zone. Lens angle = 0
• ZOOM ROTATION (available on zoom channel at 255 bit only)
BIT
128-255
127
126
125
…
1
0
MACRO EFFECT
Lens offset angle: 0.00 degree
Lens offset angle: +4.00 degree
Lens offset angle: +3.94 degree
Lens offset angle: +3.87 degree
Lens offset angle: +0.06 degree
Lens offset angle: 0.00 degree
Continue
A.LEDA B-EYE
23
➔
SHAPE SELECTION - SHAPE SPEED - SHAPE OFFSET
BIT
SHAPE SELECTION
RANDOM
COLORS *1
On
K10
On
K20
Description
Static effects.
The ring or rings
used by the
macro are
turned-on with
the foreground
colour.
0-7
8
9
10
11
12
13
14
15
Macro OFF
Ring 1
Ring 2
Ring 3
Ring 4
Ring 1 + 2
Ring 1 + 3
Ring 1 + 4
Ring Opening (Closing)
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
16
Ring Opening (Closing) Filled
Yes
Yes
Yes
17
Ring Open/Close (close/open)
Yes
Yes
Yes
18
Ring Open/Close (close/open)
Filled
Yes
Yes
Yes
19
Random pixels distribuited on
many fixtures
Yes
Yes
Yes
20
Random pixels with variable
density and speed
Yes
Yes
Yes
N.a.
N.a.
N.a.
N.a.
Yes
0-63 =
Radius size, static.
64-158 = max to min speed,
Closing effect
159-160 = STOP
161-255 = min to max speed,
Opening effect"
0-63 =
Radius size, static.
64-158 = max to min speed,
Closing effect
159-160 = STOP
161-255 = min to max speed,
Opening effect"
0-63 = STOP
64-158 = max to min speed,
Instant-on + fadeout.
159-160 = STOP.
161-255 = min to max speed,
FadeIn + FadeOut.
0-9 → continuous
10-255 → random distribution
of flash from 2 to 20 fixtures"
Rainbow 1, variable speed.
Yes
Yes
N.a.
22
Rainbow 2, fixed speed
with variable color offset.
Yes
Yes
N.a.
30-255
Fan (3 arms)
Bar (2 arms)
Half moon
Triangle
Two rotating bars of different colors
Two rotating arcs of different colors
Two rotating arcs of different colors
and direction
Reserved
Yes
Yes
Yes
Yes
Yes
Yes
Yes
N.a.
Yes
Yes
Yes
Yes
Yes
Yes
Yes
N.a.
*1: Random colors activation with foreground R,G,B,W = 0
A.LEDA B-EYE
24
SHAPE OFFSET
N.a.
N.a.
21
23
24
25
26
27
28
29
SHAPE SPEED
Fade or snap depending
on fade channel.
0-63 =
Angle 0-360°, static.
64-158 = max to min speed,
c.cw rotation
159-160 = STOP
161-255 = min to max speed,
cw rotationt
0-63 =
STOP
64-158 = c.cw rotation
159-160 = STOP
161-255 = cw rotationt
The value 64-158 or 161-255
change the rainbow angle offset
(the orange starting angle).
0-63 =
angle offset, 0-360°
64-158 = max to min speed,
c.cw rotation
159-160 = STOP
161-255 = min to max speed,
cw rotationt"
N.a.
0-255 → select random distribution
from 2 up to 20 fixtures
0-255 → select pixel density
0-255 → angle offset from 0 to 360°
N.a.
0-255 → angle offset from 0 to 360°
N.a.
Macro Off
DMX channel value: from 0 to 7.
No shape effects activated. Turns off any previously selected shape.
Static Rings
DMX channel value: from 8 to 14.
The ring or rings used by the macro are turned on with the foreground colour (Shape Red+Shape Green+Shape blue+Shape White).
Avaliable combinations: Ring 1 On, Ring 2 On, Ring 3 On (Aleda K10, K20 only), Ring 4 On (Aleda K20 only),Ring 1+2 On,
Ring 1+3 On (Aleda K10, K20 only), Ring 1+4 On (Aleda K20 only).
Dynamic Rings
DMX channel
Dynamic Rings
DMX channel value: From 15 to 18.
The rings used by the macro are turned on sequentially, simulating an opening , closing or both.
The Shape Speed channel increases the speed from 126 (min speed) to 0 (max speed) for the closing and closing/opening effects and from 129 (min
speed) to 255 (max speed) for the opening and opening/closing effects. With DMX value = 127 or 128 the macro stays still.
The Shape Offset channel defines the macro effect distribution over a number of fixtures (affects also the behavior of a single fixture)
Dmx values from 0 to 9: continous distribution;
Dmx values from 10 to 255 random distribution of flash from 2 to 20 fixtures.
If foreground colors are all set to 0, the Random-Colors mode is activated.
The color used by the macro changes at every restart.
Rings with variable radius
DMX channel value: 19 - 20.
The Shape Speed channel defines the ring radius: 0 = min, 255 = max.
Random pixels
DMX
Random pixels
DMX channel value: 21 – 22.
Leds are turned on and off randomly.
The Shape Speed channel increases the speed and defines the fade effect for the leds: from 126 (min speed) to 0(max speed) with a Instant-on/ fade-out
led effect, and from 129 (min speed) to 255 (max speed)with a fade-in + fade-out led effect. At a DMX value of 127 and 128 the macro stays still.
For macro 21 the Shape Offset channel defines leds random distribution from 0 (2 fixtures) to 255 over a set of fixtures (20 fixtures).
For macro 22 the Shape Offset channel defines pixels density from 0 (min density) to 255 (max density).
If foreground colors are all set to 0 the Random-Colors mode is activated.
The Shape Smoothing channel adjusts the fading effect applied to the macro movement
Rainbows
DMX channel value: 23 – 24 .
It simulates a rainbow effect.
The Shape Speed channel increases the speed and defines the rotation : from 126 (min speed) to 0 (max speed) counter clock wise rotation and from 129
(min speed) to 255 (max speed) clock wise rotation. With DMX value 127 or 128 the macro stays still.
For the macro 24 (Rainbow with fixed speed) the Shape Speed channel also defines angle offset (the orange sector starting angle).
Rotating shapes
DMX channel value: from 25 to 31.
Shapes avaliable: Fan (3 arms), Bar (2 arms), Half Moon, Triangle, Two rotating bars of different colors, Two rotating arcs of different colors, Two rotating
arcs of different colors and direction.
The Shape Speed channel increases the speed and defines the rotation : from 126 (min speed) to 0 (max speed) counter clock wise rotation and from 129
(min speed) to 255 (max speed) clock wise rotation. With DMX value 127 or 128 the macro stays still.
The Shape Offset channel defines the angle offset from 0 (0 degree) to 255 (360 degree).
Continue
A.LEDA B-EYE
25
➔
• SHAPE FADE
EFFECT
BIT
246-255
245
243
244
18
17
16
0-15
Smooth, fading curve with automatic gamma *
Smooth, fading curve gamma 2
Smooth, fading curve gamma 1,986
Smooth, fading curve gamma 1,993
Smooth, fading curve gamma 0,513
Smooth, fading curve gamma 0,506
Smooth, fading curve gamma 0,5
Snap
• SHAPE RGBW
SHAPE DIMMER
BACKROUND DIMMER
BIT
EFFECT
255
LED ON
0
LED OFF
• SHAPE TRANSITION
BIT
EFFECT
255
4 sec
216
3 sec
171
2 sec
113
1 sec
73
0,5 sec
5
100 ms
0-4
No fade
A.LEDA B-EYE
26
A.LEDA B-EYE K10 & K10 EASY
LED reference number for pixel mapping
TILT: channel 16 @ bit 200
13
14
12
15
4
11
5
16
LED
3
6
1
10
17
2
7
18
9
19
8
A.LEDA B-EYE K20
LED reference number for pixel mapping
TILT: channel 16 @ bit 200
28
29
30
27
26
13
14
4
5
31
12
15
25
11
LED
3
24
32
16
6
1
33
10
17
2
23
7
9
22
8
19
20
37
21
A.LEDA B-EYE
34
18
35
36
27
Cod. IST009/001 EN
PRELIMINARY 03/14
CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.it
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising