MULTIQUIP ST-1500 Specifications

MULTIQUIP ST-1500 Specifications
OPERATION AND PARTS MANUAL
SERIES
MODEL MVH-306GH
REVERSIBLE PLATE COMPACTOR
(HONDA GX270K1SMX2 GASOLINE ENGINE)
Revision #4 (08/15/07)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PROPOSITION 65 WARNING
PAGE 2 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
NOTES
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 3
TABLE OF CONTENTS
MIKASA MVH-306GH
REVERSIBLE PLATE
COMPACTOR
Proposition 65 Warning ..............................................2
Table Of Contents ......................................................4
Parts Ordering Procedures ........................................5
Safety Message Alert Symbols .............................. 6-7
Rules for Safe Operation ....................................... 8-9
Operation and Safety Decals ...................................10
Specifications ...........................................................11
Dimensions ..............................................................12
Features ...................................................................13
Plate Compactor Components .................................14
Engine Components ................................................15
Pre-Inspection .................................................... 16-17
Operation ........................................................... 18-21
Maintenance ...................................................... 22-25
Troubleshooting (Engine) .........................................26
Troubleshooting (Compactor) ..................................27
PARTS ILLUSTRATIONS
Explanation Of Code In Remarks Column ...............28
Suggested Spare Parts ............................................29
Nameplate and Decals....................................... 30-31
Vibrating Plate Assembly ................................... 32-33
Base and Engine Assembly ............................... 34-37
Vibrator Assembly .............................................. 38-39
Control Handle Assembly .................................. 40-43
Hand Pump Assembly........................................ 44-45
HONDA GX270K1SMX2 GASOLINE ENGINE
Air Cleaner Assembly......................................... 46-47
Camshaft Assembly ........................................... 48-49
Carburetor Assembly ......................................... 50-51
Control Assembly ............................................... 52-53
Crankcase Cover Assembly ............................... 54-55
Crankshaft Assembly ......................................... 56-57
Cylinder Barrel Assembly ................................... 58-59
Cylinder Head Assembly .................................... 60-61
Fan Cover Assembly .......................................... 62-63
Flywheel Assembly ............................................ 64-65
Fuel Tank Assembly ........................................... 66-67
Ignition Coil Assembly ........................................ 68-69
Muffler Assembly ............................................... 70-71
Piston Assembly ................................................. 72-73
Recoil Starter Assembly..................................... 74-75
Labels Assembly ................................................ 76-77
Terms and Conditions Of Sale — Parts .................. 78
Specification and part number are
subject to change without notice.
PAGE 4 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
www.multiquip.com
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Effective:
January 1st, 2006
Best Deal!
Order via Internet (Dealers Only):
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
[email protected]
Order parts on-line using Multiquip’s SmartEquip website!
■ View Parts Diagrams
■ Order Parts
■ Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Goto www.multiquip.com and click on
Order Parts to log in and save!
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Order via Phone: Domestic (US) Dealers Call:
1-800-427-1244
Non-Dealer Customers:
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
Dealer Name and Address
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
Quantity, Part Number and Description of Each Part
❒
Specify Preferred Method of Shipment:
✓ UPS/Fed Ex
✓ DHL
■ Priority One
✓ Truck
■ Ground
■ Next Day
■ Second/Third Day
All orders are treated as Standard Orders
and will ship the same day if received prior
to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 5
MVH-306GH — SAFETY MESSAGE ALERT SYMBOLS
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!
Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.
NOTE
This Owner's Manual has been developed to provide
complete instructions for the safe and efficient operation
of the MQ Mikasa Model MVH-306GH Reversible Plate
Compactor. Refer to the engine manufacturer’s
instructions for data relative to its safe operation.
Before using this reversible plate compactor, ensure
that the operating individual has read and
understands all instructions in this manual.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
DANGER
You WILL be KILLED or SERIOUSLY INJURED
if you DO NOT follow these directions.
WARNING
You CAN be KILLED or SERIOUSLY INJURED if
you DO NOT follow these directions.
CAUTI
CAUTION
You CAN be INJURED if you DO NOT follow
these directions.
HAZARD SYMBOLS
Lethal Exhaust Gases
Engine exhaust gases contain poisonous
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
Explosive Fuel
GASOLINE is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
use fuel as a cleaning agent.
Burn Hazards
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. Never operate the engine with heat
shields or heat guards removed.
Rotating Parts
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair and
clothing away from all moving parts to prevent
injury.
Potential hazards associated with the MVH-306GH reversible
plate compactor operation will be referenced with Hazard
Symbols which appear throughout this manual, and will be
referenced in conjunction with Safety Message Alert Symbols.
PAGE 6 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
ALWAYS place the engine ON/OFF switch in
the OFF position, when the reversible plate
compactor is not in use.
Respiratory Hazard
ALWAYS wear approved respiratory
protection.
Equipment Damage Messages
Sight and Hearing hazard
ALWAYS wear approved eye and hearing
protection.
Other important messages are provided throughout this manual
to help prevent damage to your reversible plate compactor,
other property, or the surrounding environment.
This reversible plate compactor, other property,
or the surrounding environment could be
damaged if you do not follow instructions.
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 7
MVH-306GH — RULES FOR SAFE OPERATION
CAUTION
Failure to follow instructions in this manual may lead to serious
injury or even death! This equipment is to be operated by trained
and qualified personnel only! This equipment is for industrial
use only.
The following safety guidelines should always be used when
operating the MQ Mikasa MVH-306GH Reversible Plate
Compactor:
GENERAL SAFETY
■ DO NOT operate or service this equipment before
reading this entire manual.
■ This equipment should not be operated by
persons under 18 years of age.
■ NEVER operate this equipment without proper
protective clothing, shatterproof glasses, steeltoed boots and other protective devices required
by the job. ALWAYS wear slip resistant safety
shoes or boots.
■ NEVER operate this equipment when not feeling
well due to fatigue, illness or taking medicine.
■ NEVER operate this equipment under the
influence or drugs or alcohol.
■ NEVER use accessories or attachments,
which are not recommended by Multiquip for this equipment.
Damage to the equipment and/or injury to user may result.
■ Manufacturer does not assume responsibility for any accident
due to equipment modifications.
■ Whenever necessary, replace nameplate, operation and safety
decals when they become difficult read.
■ ALWAYS wear proper respiratory (mask), hearing and eye
protection equipment when operating the reversible plate
compactor.
■ NEVER touch the hot exhaust manifold,
muffler or cylinder. Allow these parts to
cool before servicing engine or
reversible plate compactor.
■ High Temperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot components can cause serious burns.
■ The engine of this reversible plate compactor requires an
adequate free flow of cooling
air. NEVER operate the
reversible plate compactor in
any enclosed or narrow area
where free flow of the air is
restricted. If the air flow is
restricted it will cause serious
damage to the reversible plate
compactor or engine and may
cause injury to people and property. Remember the
reversible plate compactor’s engine gives off DEADLY gases.
■ ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
■ ALWAYS use extreme caution when working with flammable
liquids. When refueling, stop the engine and allow it to cool.
DO NOT smoke around or near the machine. Fire or
explosion could result from fuel vapors, or if fuel is spilled on
a hot engine.
■ NEVER operate the reversible plate compactor in an
explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe bodily
harm or even death.
■ Topping-off to filler port is dangerous, as
it tends to spill fuel.
■ ALWAYS store the reversible plate compactor in a clean, dry
location out of the reach of children.
■ NEVER run engine without air cleaner. Severe engine
damage may occur.
■ NEVER leave the reversible plate compactor unattended,
turn off engine.
■ CAUTION must always be observed while servicing this
reversible plate compactor. Rotating parts can cause injury if
contacted.
■ DO NOT leave reversible plate compactor with engine
running. Use chock blocks if parking reversible plate
compactor on a grade.
PAGE 8 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — RULES FOR SAFE OPERATION
■ NEVER disconnect any "emergency or safety devices".
These devices are intended for operator safety. Disconnection
of these devices can cause severe injury, bodily harm or even
death! Disconnection of any of these devices will void all
warranties.
Emergencies
■ ALWAYS know the location of the
nearest fire extinguisher.
Transporting
■ Always shutdown engine before transporting.
■ Tighten fuel tank cap securely and close fuel cock to prevent
fuel from spilling.
■ ALWAYS know the location of the nearest
and first aid kit.
■ Drain fuel when transporting compactor over long distances
or bad roads.
■ Always tie-down the compactor during transportation by
securing the compactor's guard frame with an appropriate
tie-down.
Loading and Unloading
■ Before lifting, make sure that machine parts (hook and
vibration insulator) are not damaged and screws are not
loosened or lost.
■ In emergencies, always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
■ ALWAYS make sure crane or lifting device has been properly
secured to the lifting bale of compactor.
■ NEVER lift the machine while the engine is running.
■ Use a reliable chain, cable or strap of adequate lifting
capacity.
■ NEVER allow any person or animal to stand underneath the
machine while lifting.
■ Use a crane with a one point suspension hook and lift straight
upwards, or use forklift to load and unload the compactor. A
skilled crane operator is required to perform the job.
Maintenance Safety
■ ALWAYS use the lifting bale (Figure 1) on the machine when
lifting is required. DO NOT use any other part of the machine
for lifting.
■ ALWAYS allow the machine a proper amount of time to
cool before servicing.
■ ALWAYS lift the machine vertically.
■ Fix damage to the machine immediately and always replace
broken parts.
■ Try not to lift machine to unnecessary heights.
■ NEVER lubricate components or attempt service on a
running machine.
■ Keep the machinery in proper running condition.
■ Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
■ DO NOT use food or plastic containers to dispose of
hazardous waste.
■ DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
Figure 1. Lifting the Compactor
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 9
MVH-306GH — OPERATION AND SAFETY DECALS
Figure 2 displays the operation and safety decals as they appear on the reversible plate compactor. Should any of these decals
become damaged or unreadable, contact the Multiquip Parts Department for a replacement set.
Figure 2. Operation and Safety Decals
PAGE 10 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH —SPECIFICATIONS
Table 1. MVH-306GH Reversible Plate
Compactor Specifications
Centrifugal Force
10,125 lb (4,602 kg)
Vibration Frequency
4,400 vpm (70 Hz)
Traveling Speed
0 to 75 ft/min (0 to 23 m/min)
Plate Size (L x W)
18 x 34 in (45.72 x 86.36 cm)
With External Plate Size (L x W)
24 x 34 in (60.96 x 86.36 cm)
Max. Area of Compaction (no extensions)
6,750 sq. ft. (2,057 sq. meters)
Overall Length
61.8 in (1570 mm)
Overall Width
18.0 in (457 mm)
Overall Height (with handle)
44.1 in (1120 mm)
Overall Height (without handle)
31.7 in (805 mm)
Operating Weight D/DS
673 lbs. ( 306 kg)
Operating Weight (with extension plates)
706 lbs. (321kg)
Table 2. Engine Specifications
Engine
Model
HONDA GX270K1SMX2
Type
4-Stroke, Single Cylinder,
OHV, Gasoline Engine
Bore X Stroke
3.0 in. X 2.3 in.
(77 mm x 58 mm.)
Displacement
16.5 cu-in (270 cm3)
Max Output
Fuel Tank Capacity
Fuel
Lube Oil Capacity
Speed Control Method
Star ting Method
Dimension
(L x W x H)
Dry Net Weight
9.0 H.P. (6.7 KW) @ 3600 R.P.M.
1.59 gallons (6.0 liters)
Unleaded Automobile Gasoline
1.16 quar ts (1.1 liters)
Centrifugal Fly-weight Type
Recoil Star t
14.0 x 16.9 X 16.1 in.
(355 X 430 X 410 mm.)
55.1 lbs (25 Kg.)
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 11
MVH-306GH — DIMENSIONS
Figure 3. MVH-306GH Reversible Plate Compactor Dimensions
Table 3. Dimensions
REF.
DIMENSIONS
A
53 in. (134.6 cm.)
B
18 in. (46 cm.)
C
34 in. (86 cm.)
D
63.8 in. (162 cm.)
E
31.7 (80.5 cm.)
PAGE 12 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH— FEATURES
Plate Compactor
Frequency/Speed
The Mikasa MVH-306GH is a walk behind, reversible plate
compactor designed for the compaction of sand, clay and
asphalt. This plate compactor is a powerful compacting tool
capable of applying a tremendous force in consecutive high
frequency vibrations to a soil surface. Its applications include
soil compacting for road, embankments and reservoirs as well
as backfilling for gas pipelines, water pipelines and cable
installation work.
The compactor's vibrating plate maximum frequency is 4400
vpm (vibrations per minute). The forward and reverse travel speed
of the compactor is approximately 75 ft./minute (23 meters/
minute).
Vibratory Plates
Controls
The vibratory plates of the MVH-306GH produce low amplitude
high frequency vibrations, designed to compact granular soils.
Before starting the MVH-306GH Plate Compactor, identify and
understand the function of the controls and components as
indicated in Figure 4.
The resulting vibrations cause forward motion. The engine and
handle are vibration isolated from the vibrating plate. The heavier
the plate, the more compaction force it generates.
Engine
The Mikasa MVH-306GH Plate Compactor is equipped with a
GX270K1-SMX2 (recoil start) gasoline engine.
Reversible Vibratory Plates
Reversible vibratory plates have two eccentric weights that allow
a smooth transition for forward and reverse travel, plus increased
compaction force as the result of dual weights.
Due to their weight and force, reversible plates are ideal for
semi-cohesive soils.
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 13
MVH-306GH— PLATE COMPACTOR COMPONENTS
Figure 4. MVH-306GH Reversible Plate
Compactor Components
Figure 4 illustrates the location of the major components for the
MVH-306GH Reversible Plate Compactor. The function of each
component is described below:
1.
Hand Grip – When operating the compactor use this hand
grip to maneuver the compactor.
2.
Forward & Reverse Lever – Push the lever forward, the
compactor will move in a forward direction, pull the lever
backwards, the compactor will move in backwards direction.
Placing the lever in the middle (midway) will cause the
compactor not to move (neutral).
3.
Handle Bar – When operating the compactor, this handle
is to be in the downward position. When the compactor is
to be stored, move the handle bar to the upright position.
4.
Guard Hook - Used to lift the machine with crane or other
lifting device.
5.
Stopper - Locks the handle in place in the upward position
for stowing.
6.
Engine – This plate compactor uses a GX270K1-SMX2
gasoline engine. Refer to the owner’s manual for engine
information and related topics.
7.
Belt Cover – Remove this cover to gain access to the Vbelts. NEVER run the compactor without the V-belt cover. If
the V-belt cover is not installed, the possibility exist that
your hand may get caught between the V-belt and clutch,
thus causing serious injury and bodily harm.
8.
Base Plate – Designed to compact sand, clay, and asphalt.
9.
Oil Reservoir – Fill with Shell Tellus Oil 46 or equivalent
grade hydraulic oil.
10. Vibration Case – Encloses the eccentric, gears and
counter weights.
11. Hydraulic Cylinder – Activated by moving the travel lever.
The cylinder controls the direction of movement by the plate
compactor.
12. Shock Absorber – Protects plate compactor from damage
by absorbing vibration during operation.
13. Throttle Lever – Controls speed of the plate compactor.
Place straight vertically to start, push fully counterclockwise
for full throttle and fully clockwise to stop plate compactor.
14. Rubber Cover – Lift this rubber cover to gain access to
the fuel tank.
PAGE 14 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH— ENGINE COMPONENTS
Figure 5. Honda GX270 Engine Components
INITIAL SERVICING
The engine (Figure 5) must be checked for proper lubrication and 6.
filled with fuel prior to operation. Refer to the manufacturers engine
manual for instructions & details of operation and servicing. The
engine shown above is a HONDA engine, operation for other 7.
types of engines may vary somewhat.
1.
Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
DANGER
Adding fuel to the tank should be done only when
the engine is stopped and has had an opportunity
to cool down. In the event of a fuel spill, DO NOT 8.
attempt to start the engine until the fuel residue has been completely
wiped up, and the area surrounding the engine is dry.
9.
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
3.
Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
4.
Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
5.
Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
Operating the engine without an air filter, with a
damaged air filter, or a filter in need of
replacement will allow dirt to enter the engine,
causing rapid engine wear.
Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
Muffler – Used to reduce noise and emissions.
WARNING
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operating. NEVER operate the engine with the muffler removed.
10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 15
MVH-306GH — PRE-INSPECTION
CAUTION
NEVER operate the compactor in a confined
area or enclosed area structure that does not
provide ample free flow of air.
4. If the oil level is low (Figure 7), fill to the edge of the oil filler
hole with the recommended oil type (Table 4). Maximum oil
capacity is 1.16 quarts (1.10 liters).
ALWAYS wear approved eye and hearing
protection before operating the compactor.
Before Starting
1.
2.
3.
Read safety instructions at the beginning
of manual.
Figure 7. Engine Oil Level
Familiarize yourself with the operating
and control elements of the machine
and the working environment. This includes obstacles in
the working area, bearing capacity of the ground and the
necessary safety provisions.
Table 4. Oil Type
Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
4.
Check fastening nuts and bolts for tightness. Loose threads
may cause damage to the machine when vibrating.
5.
Understand the geographical features and regulations of
the job site.
6.
Clean the compactor, removing dirt and dust. Particularly,
the bottom of the plate, engine cooling air inlet.
To check the engine oil level, place the compactor on secure
level ground with the engine stopped.
2.
Remove the dipstick from the engine oil filler hole (Figure 6)
and wipe it clean.
3.
Insert and remove the dipstick without screwing it into the
filler neck. Check the oil level shown on the dipstick.
Figure 6. Engine Oil Dipstick Removal
Temperature
Oil Type
Summer
25°C or Higher
SAE 10W-30
Spring/Fall
25°C~10°C
SAE 10W-30/20
Winter
0°C or Lower
SAE 10W-10
Checking the Hydraulic Oil Level
1.
To check the engine oil level, place the compactor on secure
level ground with the engine stopped.
2.
Remove the hydraulic oil breather cap located at the top of the
hydraulic oil tank (Figure 8).
3.
Using a 24 mm wrench, remove the hydraulic oil filler plug.
3.
Visually inspect to determine if hydraulic oil level is low. If oil
level is low add Shell Tellus 46 hydraulic oil or equivalent
through the hand pump oil filler port.
Checking Engine Oil Level
1.
Season
Figure 8. Hydraulic Oil Filler Plug Removal
PAGE 16 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — PRE-INSPECTION
CAUTION
DO NOT overfill hydraulic oil tank. This could cause oil leaks
and sluggish operation. Clean cap and surrounding area before
opening to prevent dirt from entering oil tank.
4.
When adding hydraulic oil, only fill to the specified oil level as
marked on the front of the hydraulic oil tank (Figure 9). DO
NOT overfill.
Explosive Fuel
DANGER
Diesel fuel is highly flammable and can be dangerous if
mishandled. DO NOT smoke while refueling. DO NOT attempt
to refuel the compactor if the engine is hot! or running.
Checking The Fuel
1. Remove the fuel cap located on top of fuel tank.
2. Visually inspect to see if fuel level is low. If fuel is low, replenish
with unleaded gasoline. (Figure 11).
3. When refueling, be sure to use a strainer for filtration. DO NOT
top-off fuel. Wipe up any spilled fuel.
Figure 9. Oil Tank (Front View)
Checking the Air Cleaner
1.
Loosen the wing nut and remove the air cleaner cover as
shown in Figure 10.
2. Remove the paper filter element and inspect it for signs of
wear or dirt. If paper filter element is dirty, clean or replace
element.
Figure 11. Refueling
DANGER
Fuel spillage on a hot engine can cause a fire or explosion.
If fuel spillage occurs, wipe up the spilled fuel completely to
prevent fire hazards. NEVER! smoke around or near the
compactor.
Figure 10. Air Cleaner Element
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 17
MVH-306GH — OPERATION
CAUTION
DO NOT attempt to operate the compactor
until the Safety, General Information and
Inspection sections of this manual have
thoroughly
been read and
understood.
This section is intended to assist the
operator with the initial start-up of the compactor. It is extremely
important that this section be read carefully before attempting to
use the compactor in the field.
Refer to Figure 4 for the location of controls and components.
Figure 13. Handle Adjustment
STARTING THE ENGINE
Releasing the Handle
Starting the Engine (HONDA engine)
1. Pull the handle release pin, (Figure 12) then push down on
the hand grip to release the handle.
1. Place the engine fuel valve lever (Figure 14) to the "ON"
position.
Figure 14. Engine Fuel Valve Lever (ON Position)
2.
Move the throttle lever to the START position (Figure 15).
Figure 12. Handle Release Pin
Adjusting Handle Height
The height of the handle is adjustable for your comfort .
1. Loosen the butterfly screw (Figure 13).
2. Turn the grip clockwise to raise the handle or counterclockwise to lower the handle.
3. When the handle is raised to the desired height, tighten the
butterfly screw.
Figure 15. Throttle Lever (Start Position)
PAGE 18 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — OPERATION
3. Place the choke lever (Figure 16) in the "OPEN " position
if starting a cold engine.
Figure 16. Engine Choke Lever (Open)
4. Place the choke lever (Figure 17) in the "CLOSED " position
if starting a warm engine or the temperature is warm.
Figure 19. Starter Grip
7. If the engine has started, slowly return the choke lever
(Figure 17) to the CLOSED position. If the engine has not
started repeat steps 1 through 6.
8. Before the compactor is placed into operation, run the engine
for several minutes. Check for fuel leaks, and noises that
would be associated with a loose component.
TRAVELING
CAUTION
Make sure to follow all safety rules referenced in the safety section
of this manual before operating compactor. Keep work area
clear of debris and other objects that could cause damage to the
compactor or bodily harm.
1. Grasp the compactor's hand grip (Figure 20), and move the
engine throttle lever (Figure 20) quickly to the fast position.
Figure 17. Engine Choke Lever (Closed)
2. With the throttle lever in the fast position, the engine speed
should be around 3,600 RPM, therefore engaging the centrifugal clutch.
5. Place the engine ON/OFF switch (Figure 18) in the "ON "
position.
Figure 20. Throttle Lever (Fast)
Figure 18. Engine ON/OFF Switch (ON Position)
6. Grasp the starter grip (Figure 19) and slowly pull it out. The
resistance becomes the hardest at a certain position, corresponding to the compression point. Pull the starter grip briskly
and smoothly for starting.
ALWAYS move the throttle lever quickly without
hesitation, because increasing the engine
speed slowly causes the clutch to slip.
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 19
MVH-306GH—OPERATION
3. To make the compactor move in the forward direction push
the travel lever ( Figure 21) forward.
Figure 23. Engine ON/OFF Switch (OFF)
Figure 21. Travel Lever
4. To make the compactor move in the reverse direction pull the
travel lever ( Figure 21) backwards.
5. Firmly gasp the compactor's hand grip, the compactor will
begin moving in the desired position when the direction lever
has been placed in the desired position.
6. Slowly walk behind the compactor and be on the lookout for
any large objects or foreign matter that might cause damage
to the compactor or bodily injury.
7. If travel lever is placed in the neutral position, the machine will
vibrate in place.
8. To move the compactor laterally, hold the hand grip firmly and
swing compactor. DO NOT swing compactor while gripping
the travel lever.
Normal Shutdown
1.
Return the throttle lever to the START position (Figure 15).
Allow the machine to cool down for 2 to 3 minutes.
2.
Place the travel lever in the NEUTRAL position.
3.
Place the throttle lever in the STOP position (Figure 22) to stop
the engine.
Figure 24. Fuel Valve Lever (OFF)
Emergency Shutdown
1. For a recoil start type engine, move the throttle lever quickly
to the STOP position.
STOWING THE HANDLE
1.
Push up the handle upward (Figure 25) until the handle locks
in place.
4. Turn the engine ON/OFF switch to the “OFF” position (Figure 23).
5. Place the fuel shut-off lever (Figure 24) in the OFF
position.
Figure 22. Throttle Lever (Stop)
Figure 25. Stowing the Handle
PAGE 20 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — MAINTENANCE
CAUTION
CAUTION
Inspection and other services should always be carried out on
hard and level ground with the engine shutdown.
Fuel piping and connections should be replaced every 2 years.
TABLE 6. MVH-306GH Engine Check
Inspection and Maintenance Service Tables.
1. To make sure your plate compactor is always in good
working condition before using, carry out the maintenance
inspection in accordance with Tables 5 through 7.
ITEM
HOURS OF OPERATION
Spark Plug Check
Every 40 hours (every week)
Oil or Fuel Leak
Every 8 hours (every day)
Tightness of Fastening
Threads
Every 8 hours (every day)
Engine Oil Check and
Replenishment
Every 8 hours (every day)
(Replenish to specified maximum
level)
Engine Oil Replacement
After first 25 hours then every 50 to
100 hours
Air Filter Cleaning
Every 100 hours
TABLE 5. MVH-306GH MACHINE INSPECTION
ITEM
HOURS OF
OPERATION
Loose or Missing
Screws
Every 8 hours
(every day)
Damaged Par ts
Every 8 hours
(every day)
REMARKS
Function of Controlling Every 8 hours
System Par t
(every day)
Hydraulic System Leak Every 100 hours
See separate engine manual for details on engine check.
See page 21
Daily Service
Vibrator Oil Check
Every 100 hours
See page 23
Vibrator Oil
Replacement
Every 300 hours
See page 23
Hydraulic Oil Check
Every 100 hours
See page 23
Hydraulic Oil
Replacement
First after 200
hours, then every See page 23
1,000 hours
Material 6mm 8mm 10mm 12mm
14mm
16mm
18mm
20mm
4T
70
150
300
500
750
1,100
1,400
2,000
V-belt (clutch) Check
Every 200 hours
See page 22
6-8T
100
250
500
800
1,300
2,000
2,700
3,800
11T
150
400
800
1,200
2,000
2,900
4,200
5,600
Battery Check
Every 100 hours
See page 24
*
100
300~ 650 ~
350 700
CAUTION
These inspection intervals are for operation under normal
conditions. Adjust your inspection intervals based on the number
hours plate compactor is in use, and particular working
conditions.
z Check for leakage of fuel or oil.
z Check for loose screws including tightness. See Table 7
below (tightening torque ), for retightening:
TABLE 7. TIGHTENING TORQUE
(in. kg/cm) Diameter
* (In case counter-par t is of aluminum)
(Threads in use with this machine are all right handed)
Material and quality of material is marked on each bolt, and screw.
z Remove soil and clean the bottom of compaction plate.
z Check hand pump, piping and hose for any leakage. A
loosened hydraulic hose can be a cause for leakage. Check
hydraulic hose connections with wrench applied for
tightness.
z Check engine oil.
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 21
MVH-306GH — MAINTENANCE
Spark Plug
Air Filter
1. Remove and clean the spark plug (Figure 26).
1. Remove the air cleaner cover and foam filter element as
shown in Figure 28.
2. Adjust the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm). This
unit has electronic ignition, which requires no adjustments.
2. Tap the paper filter element (Figure 28) several times on a
hard surface to remove dirt, or blow compressed air [not
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter
element from the air cleaner case side. NEVER brush off dirt.
Brushing will force dirt into the fibers. Replace the paper filter
element if it is excessively dirty.
3. Clean foam element in warm, soapy water or nonflammable
solvent. Rinse and dry thoroughly. Dip the element in clean
engine oil and completely squeeze out the excess oil from the
element before installing.
Figure 26. Spark Plug Gap
Engine Oil Replacement
1. Replace engine oil, first in 25 hours of operation and every
50 to 100 hours afterwards.
2. Drain the engine oil when the oil is warm as shown in
Figure 27.
3. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
4. Replace engine oil with recommended type oil as listed
in Table 4. Engine oil capacity is 1.16 quarts (1.1 liters).
DO NOT overfill.
5. Install drain bolt with sealing washer and tighten securely.
Figure 28. Engine Air Filter
CAUTION
NEVER attempt to check the V-belt with the engine running.
Severe injury can occur if your hand gets caught between the Vbelt and the clutch (Figure 29). Always use safety gloves.
CLUTCH
PULLEY
Figure 27. Engine Oil (Draining)
VIBRATOR
PULLEY
Figure 29. V-Belt Hazard
PAGE 22 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — MAINTENANCE
Checking and Replacing the V-Belt and Clutch
Vibrator Oil Level Check
1. After 200 hours of operation, remove the belt cover to check
CAUTION
the V-belt tension (Figure 30). Tension is proper if the belt
bends about 3/8”(10 mm) when depressed strongly with Always clean the area around the vibrator oil level check plug
finger between shafts. Loose or worn V-belts reduces power before removing oil check plug. This will prevent dirt and debris
transmission efficiency, causing weak compaction and from entering the system.
reduces the life of the belt itself.
1. In every 100 hours of operation, with the machine positioned
horizontally, use a 3/4” (19 mm) wrench and remove vibrator
oil level check plug (Figure 31). Visually inspect and see if
vibrator oil level is up to filler port. Be sure to clean area
around check hole to prevent dirt and dust from entering.
Figure 30. V-Belt Check
z Replacing the V-belt
Remove the belt cover. Engage an offset wrench 3/4”(19 mm) or
the like to vibrator pulley (lower) fastening bolt. Engage waste
cloth or the like at midway of V-belt on the left side and while
Figure 31. Vibrator Oil Drain and Check Plugs
pulling it back strongly, rotate the offset wrench clockwise so that
the V-belt will come off.
Draining Vibrator Oil
1. Replace vibrator oil after first 200 hours and in every 1,000
z Reinstalling the V-belt
hours of operation.
Engage V-belt to lower vibrator pulley and push the V-belt to left
side of upper clutch and, in the same manner as in removal, 2. Position handle bar vertically (storage position).
rotate offset wrench clockwise so that the V-belt goes back on. 3. Using a 14 mm wrench remove the vibrator oil drain plug
(Figure 31) from the vibrating plate assembly.
z Checking Clutch
Check the clutch simultaneously with V-belt checking. With belt
cover removed, check outer drum of the clutch for seizure and
"V" groove for wear or damage with your eyes. Clean the "V"
groove as necessary. Wear of lining or shoe should be checked
with running check. If the shoe is worn, power transmission
becomes deficient and slipping will result.
z Replacing Clutch
Remove V-belt. Remove bolt at engine power output by giving a
shock to an engaged wrench (tapping with hammer or the
like)and rotating bolt counterclockwise. Remove clutch with a
pulley extractor. To reinstall, reverse the procedure.
CAUTION
Whenever the compactor's vibration becomes weak or lost during
normal operation regardless of operation hours, check the V-belt
and clutch immediately.
For draining oil through level check hole, have
the machine inclined with a sleeper or the like
placed under the compaction plate on opposite
side.
4. After vibrator oil has been completely drained from machine,
fill with 10W-30 motor oil to the appropriate safe operating
level (Figure 31).
5. Reinstall drain plug into vibrating plate assembly. Apply seal
tape or Loctite #575 to thread portion of drain plug.
Draining Hydraulic Oil
1. Disconnect the hydraulic hose connected to the hydraulic
oil cylinder (Figure 32).
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 23
MVH-306GH—MAINTENANCE
CAUTION
Make sure hydraulic oil is at a normal safe operating level. DO
NOT over fill. Over filling (excessive oil) will cause excess oil to
blow out of breather plug.
Figure 32. Hydraulic Oil Cylinder
2. Push the travel lever back and forth to drain the hydraulic oil
from the hand pump (hydraulic oil reservoir).
3. Loosen bleeder plug located at top of hydraulic cylinder on
side of vibrator (Figure 35). Air remaining in the circuit will
be forced out of the bleeder plug. Once all air has been
purged from the hydraulic system, tighten bleeder plug
securely
4. Re-insert oil plug into hydraulic oil tank and tighten securely.
Re-install breather cap.
3. After draining hydraulic oil, reconnect hydraulic oil hose to
cylinder.
4. Place handle in upright position. Pull travel lever all the way
back (reverse), and using a rope, secure travel lever to hand
grip.
Adding Hydraulic Oil
1. Remove the breather cap and oil plug (Figure 33) from the
hydraulic oil tank using a 24mm hex socket.
Figure 35. Bleeder Plug
LONG TERM STORAGE
When storing your compactor for long periods do the following:
z Run the engine at idle speed for 3-5 minutes.
z Stop the engine. Drain the engine crankcase oil while the
engine is still warm. Fill engine crankcase with fresh oil.
z Wipe any oil or dirt that may have accumulated on the
compactor.
Figure 33. Hydraulic Oil Tank
2. Using a funnel, add Shell Tellus Oil #46 or equivalent to the z Store compactor in a cool dry place out of reach of children
hydraulic oil tank through the oil filler port (Figure 34). Oil
and unauthorized personnel..
tank capacity is 50.7 fl. oz (1500 cc)
Troubleshooting
See Tables 8 (engine) and 9 (plate compactor) on proceeding
pages for engine and plate compactor troubleshooting guide.
Figure 34. Hydraulic Oil Maintenance
PAGE 24 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH—TROUBLESHOOTING
Practically all breakdowns can be prevented by proper diagnosis based on the Engine Troubleshooting (Table 8)
handling and maintenance inspections, but in the event of a information shown below. If the problem cannot be remedied,
please leave the unit just as it is and consult our company's
breakdown, please take a remedial action following the
business office or service plant.
TABLE 8. ENGINE TROUBLESHOOTING
SYMPTOM
Difficult to star t, "fuel is available, but no
SPARK at spark plug".
POSSIBLE CAUSE
Spark plug bridging?
Check gap, insulation or
replace spark plug.
Carbon deposit on spark plug?
Clean or replace spark plug.
Shor t circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
Set to proper gap.
ON/OFF switch is shor ted?
Check switch wiring, replace
switch.
Ignition coil defective?
Replace ignition coil.
Difficult to star t, "fuel is available, and Improper spark gap, points dir try?
SPARK is present at the spark plug".
Difficult to star t, "fuel is available, spark
is present and compression is normal"
Difficult to star t, "fuel is available, spark
is present and compression is low"
No fuel present at carburetor.
SOLUTION
Set correct spark gap and
clean points.
Condenser insulation worn or shor t
circuiting?
Replace condenser.
Spark plug wire broken or shor t circuiting?
R e p l a c e d e fe c t i ve s p a r k p l u g
wiring.
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Water or dust in fuel system?
Flush fuel system.
Air cleaner dir ty?
Clean or replace air cleaner.
Suction/exhaust valve stuck or protruded?
Re-seat valves.
Piston ring and/or cylinder worn?
Replace piston rings and or
piston.
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and spar k plug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Fuel cock does not open properly?
Apply lubr icant to loosen fuel
cock lever, replace if necessary.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Clean or replace fuel tank cap.
Air in fuel line?
Bleed fuel line.
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 25
MVH-306GH—TROUBLESHOOTING
TABLE 8. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
"Weak in power" compression is proper
and does not misfire.
POSSIBLE CAUSE
SOLUTION
Air cleaner not clean?
Clean or replace air cleaner
Improper level in carburetor?
Check float adjustment, re-build
carbureator.
Defective Spark plug?
Clean or replace spark plug.
Defective Spark plug?
"Weak in power" compression is proper
but misfires.
Engine overheats.
Rotational speed fluctuates.
Recoil starter malfunction.
Water in fuel system?
Flush fuel system, and replace
with correct type of fuel.
Dirty spark plug?
Clean or replace spark plug.
Ignition coil defective?
Replace ignition coil.
Spark plug heat value improper?
Replace with correct type of
spark plug.
Correct type of fuel?
Replace with correct type of fuel
Cooling fins dirty?
Clean cooling fins.
Governor adjusted correctly?
Adjust governor.
Governor spring defective?
Replace governor spring.
Fuel flow restricted?
Check entire fuel system for leaks
or clogs.
R e c o i l me c h a n i s m c l o g g e d w i t h d u s t a n d
dirt?
Clean recoil assembly with soap
and water.
Sprial spring loose?
Replace sprial spring.
PAGE 26 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH—TROUBLESHOOTING
Practically all breakdowns can be prevented by proper diagnosis based on the Compactor Troubleshooting (Table 9)
handling and maintenance inspections, but in the event of a information shown below. If the problem cannot be remedied,
please leave the unit just as it is and consult our company's
breakdown, please take a remedial action following the
business office or service plant.
TABLE 9. TROUBLESHOOTING COMPACTOR
SYMPTOM
Travel speed low and vibration weak.
POSSIBLE CAUSE
Clutch slips?
Adjust or replace clutch.
V-belt slips?
Adjust or replace V-belt.
Excessive Oil in vibrator?
Fill to correct level..
Trouble in vibrator internals?
Check vibrator assembly for any worn or
defective par ts, replace any defective
par ts.
Aeration in hydraulic oil for for travel
reversing syste.?
Purge air in hydraulic oil. (Bleed plug)
Engine speed incorrect?
Set engine speed to correct RPM.
Travel reversing system inoperative.?
Check entire travel system.
Reversing lever installation correct?
Clean installation of reversing lever.
Broken or defective oil hose?
Replace oil hose.
Travels forward or backward but unable Aeration in hydraulic oil for for travel
reversing syste.?
to switch direction.
Does not travel in forward or reverse.
Reversing lever operating resistance
great.
SOLUTION
Purge air in hydraulic oil. (Bleed plug)
Excessive oil in reversing system?
Fill to correct level..
Selector valve clogged with trash?
Clean selector valve.
Cylinder piston bearing failure?
Check piston bearing in cylinder for
leakage at USH packing.
V-belt dis-engaged or slips?
Engage V-belt, adjust or replace.
Clutch slips?
Adjust clutch, replace if necessary.
Pump input shat key or adapter key-way
damaged?
Replace input shatkey or adapter key-way
Cylinder piston bearing failure?
Check piston bearing in cylinder for
leakage at USH packing.
Excessive hydraulic oil?
Fill to correct level.
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 27
MVH-306GH — EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and
remarks used in the Parts section of this manual. Use the help
numbers found on the back page of the manual if there are any
questions.
The contents and part numbers listed in the parts section are
subject to change without notice. Multiquip does not
guarantee the availibility of the parts listed.
*
*
Numbers Used - Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
REMARKS Column
Sample Parts List:
NO.
1
2
2
3
4
QTY. Column
PART NO. PART NAME
QTY. REMARKS
12345
BOLT ...................... 1 ......INCLUDES ITEMS W/
WASHER, 1/4 IN. ............. NOT SOLD SEPARATELY
12347
WASHER, 3/8 IN. ... 1 ......MQ-45T ONLY
12348
HOSE ................... A/R ....MAKE LOCALLY
12349
BEARING ............... 1 ......S/N 2345B AND ABOVE
*
NO. Column
Unique Symbols - All items with same unique symbol
( , #, +, %, or >) in the number column belong to the same
assembly or kit, which is indicated by a note in the “Remarks”
column.
*
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general
item, such as different size saw blade guards in use or a
part that has been updated on newer versions of the same
machine.
When ordering a part that has more than one
item number listed, check the remarks column for
help in determining the proper part to order.
PART NO. Column
Numbers Used - Part numbers can be indicated by a
number, a blank entry, or TBD.
TBD (To Be Determined) is generally used to show a part
that has not been assigned a formal part number at time of
publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
Assembly/Kit - All items on the parts list with the same
unique symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
Serial Number Break - Used to list an effective serial
number range where a particular part is used.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use - Indicates that the part is
used only with the specific model number or model number
variant listed. It can also be used to show a part is NOT
used on a specific model or model number variant.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
PAGE 28 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — SUGGESTED SPARE PARTS
MVH-306 W/HONDA GX270K1SMX2 ENGINE
1 to 3 Units
Qty. ... P/N ...................... Description
1 ....... 956100055 .......... THROTTLE WIRE
2 ....... 070200363 .......... V-BELT
3 ....... 9807955846 ......... SPARK PLUG
3 ....... 17210ZE2822 ...... ELEMENT, AIR CLEANER (DUAL)
1 ....... 17620Z0T814 ...... CAP, FUEL TANK
1 ....... 28462ZE2W11 ..... ROPE, RECOIL
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 29
MVH-306GH — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
PAGE 30 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
NO.
1
3
4
5
6
7
8
9
10
11
PART NO.
920201950
920110370
920209620
920207480
920204580
920203330
920211060
920201580
920211010
PART NAME
QTY.
REMARKS
DECAL: OIL SAE 10W-30 ........................... 1......... NPA-195
DECAL: MODEL LOGO
1
DECAL: CAUTION ...................................... 1......... NPA-962
DECAL: SHELL TELLUS OIL 46 ................ 1......... NPA-748
DECAL: FULL THROTTLE .......................... 1......... NPA-458
DECAL: EAR PROTECTION ...................... 1......... DCL333
DECAL: CAUTION (TRAVEL LEVER) ........ 1......... NPA-1106
DECAL: SERIAL NO. .................................. 1......... CONTACT MQ PARTS DEPT.
DECAL: MQ LOGO
1
DECAL: V-BELT HDPF-5370 ...................... 1......... NPA-537
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 31
MVH-306GH — VIBRATING PLATE ASSY.
VIBRATING PLATE ASSY.
PAGE 32 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — VIBRATING PLATE ASSY.
VIBRATING PLATE ASSY.
NO.
PART NO.
1
464117840
2
953405840
3
953402930
4
953400270
5
953405260
6
939010260
7
020316130
8
030216400
9
001221635
10
001221830
11
58407
12
030216400
15
939010010
16
020310080
17
031110160
18
030210250
19
464343730
20
011008015
21
030208200
31
52993
32
012218050
33
58407
PART NAME
VIBRATING PLATE
DRAIN PLUG MI8 (H)
COPPER PACKING 19X30X1
PLUG 1/4X14 10L
PACKING 1/4 (CU)
SHOCK ABSORBER 110X60H
NUT M16
WASHER, LOCK M16
BOLT 16X35 T
BOLT 18X30 T
WASHER, LOCK M18
WASHER, LOCK M16
SHOCK ABSORBER, STOPPER 45
NUT M10
WASHER, FLAT M10
WASHER, LOCK M10
COVER, VIBRATING PLATE
BOLT 8X15 T
WASHER, LOCK M8
EXTENSION PLATE
BOLT 18X50 T
WASHER, LOCK M18
QTY.
1
1
1
1
1
4
4
4
4
8
8
4
4
4
4
4
2
8
8
2
8
8
REMARKS
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 33
MVH-306GH — BASE AND ENGINE ASSY.
BASE AND ENGINE ASSY.
PAGE 34 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — BASE AND ENGINE ASSY.
BASE & ENGINE ASSY.
NO.
PART NO.
1
464117850
2
912227003
3
0105051045
4
030210250
5
031110160
6
464216580
7
001121025
8
030210250
9
031110160
10
464343670
11
464457360
12
456343340
13
951400110
14
952400690
15
001220830
16
030208200
17
464216640
18
092006010
19
464343660
20
464216590
21
001521050
26
464457430
35
464117920
36
456449950
37
011208030
38
030208200
39
031108160
40
022710809
PART NAME
BASE
ENGINE ASSY., GX270K1SMX2 (HONDA)
BOLT 10X45 T
WASHER, LOCK M10
WASHER, FLAT M10
BELT COVER (IN)
BOLT 8X25 T
WASHER, LOCK M10
WASHER, FLAT M10
DUST-PROOF SPONGE (IN)
SPACER
CLUTCH ASSY./CHM03/W.FAN
KEY 7X7X35
WASHER 9X35X4.5
BOLT 8X30 T
WASHER, LOCK M8
DUST-PROOF COVER
FLAT HEAD SCREW 6X10
DUST-PROOF SPONGE (OUT)
BELT COVER (OUT)
SOCKET HEAD BOLT 10X50 T
SPACER, ENGINE
RUBBER COVER (GUARD FRAME)
PLATE, COVER
BOLT 8X30 T
WASHER, LOCK M8
WASHER, FLAT M8
NYLON NUT M8
QTY.
1
1
4
4
4
1
4
4
4
1
1
1
1
1
1
1
1
3
1
1
4
2
1
1
1
3
3
3
REMARKS
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 35
MVH-306GH — BASE AND ENGINE ASSY. (CONTINUED)
BASE AND ENGINE ASSY. (CONTINUED)
PAGE 36 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — BASE AND ENGINE ASSY. (CONTINUED)
BASE AND ENGINE ASSY. (CONTINUED)
NO.
41
42
43
44
45
46
47
48
51
52
53
59
60
61
62
63
64
70
71
72
PART NO.
459010060
459010070
459010090
459010080
0401140030
464457380
014208020
030208200
464117900
012214030
030214350
90131ZE3790
9410912000
070200363
0830000010
151010680
58151
959407260
001221015
030210250
PART NAME
UNION TIP, DRAIN
DRAIN HOSE
HOSE BAND
GASKET(OIL DRAIN)
PLUG
DRAIN JOINT
BOLT 8X20 T
WASHER, LOCK M8
GUARD HOOK
BOLT 14X30 T
WASHER, LOCK M14
DRAIN JOINT
WASHER, DRAIN PLUG M12
V-BELT
COIL SPRING
CLAMP CP.
WASHER, FLAT M5
CLIP D6 (FOR M10)
BOLT 10X15 T
WASHER, LOCK M10
QTY.
1
1
2
2
1
1
1
1
1
4
4
1
1
1
1
1
1
1
1
1
REMARKS
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 37
MVH-306GH — VIBRATOR ASSY.
VIBRATOR ASSY.
PAGE 38 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — VIBRATOR ASSY.
VIBRATOR ASSY.
NO.
PART NO.
1#
464117880
2
001221470
3
001221450
4
030214350
5#
047920120
6#
457212410
8#
951405370
9#
456327150
10#
080200550
11#
060105030
12#
951404970
13#
464343700
14#
009120301
15#
456337670
16#
009120302
17#
456337380
18#
456010010
19#
464343720
20#
040006911
21#
953010030
25#
042506000
26#
080200100
27#
455435051
28#
455010070
29#
080100260
30#
456327130
31#
456210636
33#
050101050
34#
0012221025
35#
030210250
36#
011008015
37#
953404600
38#
455010020
39#
031110160
43#
952405470
46#
464343710
47#
464457370
48#
012212030
49#
030212300
51
464216600
52
001520852
53
464910020
PART NAME
QTY.
REMARKS
VIBRATING CASE
1
BOLT 14X150 T
6
BOLT 14X50 T
4
WASHER, LOCK M14
10
ROLLER BEARING NJ310EMC4
4
ROTARY SHAFT, DRIVE
1
KEY 15X10X39 RR
1
GEAR, DRIVE
1
STOP RING S-55
2
OIL SEAL SB-50729
1
KEY 12X8X30 R
1
ECCENTRIC ROTATOR
4
SOCKET HEAD BOLT 16X40 T
2
ROTARY SHAFT, DRIVEN
1
SOCKET HEAD BOLT 16X30 T
2
PISTON ROD
1
KNOCK PIN 10X70
1
GEAR (DRIVEN)
1
BEARING 6911
2
SEAL CAP/SC72-8N
1
BEARING 6000ZZSG
2
STOP RING S-10
1
PISTON, 22.4D
1
PACKING USH-22.4X30X5
1
STOP RING R-26
1
BEARING COVER
1
CYLINDER (L)/(AC)
1
O-RING G-105
2
BOLT 10X25 T
8
WASHER, LOCK M10
8
BOLT 8X12 T
1
COPPER PACKING 8X16X2
1
ELBOW 45 DEG. 15-0404
1
WASHER, FLAT M10
4
SHIM 90X110X0.5
2
PULLEY
1
WASHER
1
BOLT 12X30 T
1
WASHER, LOCK M12
1
BELT COVER (LOWER)
1
SOCKET HEAD BOLT 8X60 T
5
VIBRATOR ASSY ................................................1 ............. INCLUDES ITEMS W/#
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 39
MVH-306GH — CONTROL HANDLE ASSY.
CONTROL HANDLE ASSY.
PAGE 40 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — CONTROL HANDLE ASSY.
CONTROL HANDLE ASSY.
NO.
PART NO.
1
464343680
2
456336420
3
012212035
4
030212300
5
031112230
7
456336400
8
456449940
9
456449930
10
001221681
11
032124400
12
025306016
13
0401450160
14
020316130
15
020416100
18
455434950
19
455010030
20
939010060
21
020310080
22
020412070
23
022411635
25
954404230
26
011206020
27
030206150
28
952404470
29
020106050
34
501402870
35
501402880
36
959403460
37
020310080
38
456449980
39
953405260
40
031110160
43
464343690
44
0105050616
45
030206150
46
952404470
47
464457710
48
464457720
49
454010020
PART NAME
HANDLE BRACKET
HANDLE BRACKET (R)
BOLT 12X35 T
WASHER, LOCK M12
WASHER, FLAT M12
RUBBER COUPLING
SHOCK ABSORBER
RUBBER PLATE
BOLT 16X250 T
CONICAL SPRING WASHER M24
SPRING PIN 6X16
WASHER, FLAT M16
NUT M16
NUT M16, H=10
SPINDLE
KNOB
SHOCK ABSORBER
NUT M10, H=6
NUT M12, H=7
WING NUT M16
CLAMP SA120-18
BOLT 6X20 T
WASHER, LOCK M6
WASHER, FLAT M6
NUT M6
HANDLE STOPPER
SPRING/HANDLE (1.4X18X44)
BALL GRIP 32D-M10
NUT M10, H=6
RUBBER PACKING 9D-20D-5T
PACKING 1/4 (CU)
WASHER, FLAT M10
HANDLE COVER
BOLT 6X15 T
WASHER, LOCK M6
WASHER, FLAT M6
PACKING A, HANDLE COVER
PACKING B, HANDLE COVER
CLAMP TC-100
QTY.
1
1
4
4
4
2
2
2
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6
6
6
1
1
1
REMARKS
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 41
MVH-306GH — CONTROL HANDLE ASSY. (CONTINUED)
CONTROL HANDLE ASSY.
PAGE 42 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — CONTROL HANDLE ASSY. (CONTINUED)
CONTROL HANDLE ASSY.
NO.
PART NO.
61
464117890
64
464216630
65
464457400
66
012010030
67
030210250
68
464216620
69
030210250
70
031110160
71
020310080
72
011208025
73
030208200
80
464457340
81
959403840
82
464457420
83
464457350
84
001520820
85
031116260
86
458460660
87
033910080
88
464457440
89
464010010
90
001220625
91
020306050
93
464010020
94
001520520
95
031105080
96
20305040
99
954002270
101
956100055
103
454010020
104
959021815
104
959021810
PART NAME
HANDLE
TRAVEL LEVER
HANDLE BOSS
BOLT 10X30 T
WASHER, LOCK M10
GRIP
WASHER, LOCK M10
WASHER, FLAT M10
NUT M10
BOLT 8X25 T
WASHER, LOCK
THROTTLE LEVER
BAR GRIP I.D. 12 MM
COVER, THROTTLE
ARM, THROTTLE
SOCKET HEAD BOLT 8X20 T
WASHER, FLAT
WASHER 16.4-35-0.6
CONICAL SW 16.3 X 31.5 X 1.2
STEEL BALL D6 (SUJ)
DRY BUSHING/ LBF-1620
BOLT 6X25 T
NUT M6
ROD END M5
SOCKET HEAD BOLT 5X20 T
WASHER, FLAT M5
NUT M5
OIL HOSE W/SPRING 1/4 X 920
THROTTLE WIRE
CLAMP TC-100
SPRIAL TUBE 6D-330L
SPRIAL TUBE KEP6/ L=500
QTY.
1
1
1
2
2
1
2
2
2
2
2
1
1
1
1
1
1
2
3
1
1
2
2
1
1
1
1
1
1
1
1
1
REMARKS
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 43
MVH-306GH — HAND PUMP ASSY.
HAND PUMP ASSY.
PAGE 44 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
MVH-306GH — HAND PUMP ASSY.
HAND PUMP ASSY.
NO.
B
*
C
*
2
*
3
*
4
*
9
*
10
*
11
*
12
*
13
*
14
*
15
*
16#
*
17#
*
18#
*
19#
*
22
*
22
*
26#
*
27#
*
28#
*
50
*
51
*
52#
*
53#
*
81
*
82
*
83
*
84
PART NO.
4649-10040
464910080
464010040
464010050
464010060
464010070
099205005
464010080
464010090
464010100
458010080
001520620
050200200
050200220
050300380
050200180
464010110
464010111
050300400
050200150
050100400
464010120
458451630
069904010
069901010
984010030
984010040
984010050
464216721
PART NAME
QTY.
REMARKS
ACCUMLATOR
1
O-RING DUST,SEAL,SET ...................... 1 ............. INCLUDES ITEMS W/#
CONTROL SHAFT
1
BUSH
2
CAM
1
STOPPER
2
SOCKET HEAD SCREW 5X5 T
2
PLUG
1
PIN,STOPPER
2
PLUG
2
BREATHER
1
SOCKET HEAD BOLT 6X20 T
1
O-RING P-20
2
O-RING P-22
2
O-RING S-38
1
O-RING P-18
1
ACCUMULATOR CASE ..........................1 ............. S/N N2418 AND BELOW
ACCUMULATOR CASE ..........................1 ............. S/N N2419 AND ABOVE
O-RING S-40
1
O-RING P-15
1
O-RING G-40
1
SPRING PLUG
1
BREATHER CAP
1
DUST SEAL SER-40 .............................. 1 ............. S/N N2419 AND ABOVE
DUST SEAL SER-15 .............................. 1 ............. S/N N2419 AND ABOVE
SPRG.COMPRESSION TOOL
1
DISASSEMBLING TOOL A
1
DISASSEMBLING TOOL B
1
HAND PUMP ASSY ............................... 1 ............. INCLUDES ITEMS W/
*
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 45
GX270K1-SMX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 46 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
PART NO.
1
16271ZE2010
2
17210ZE2822
3
* 17218ZE2821
5
17231ZH9820
6
* 17232891000
17238ZE2310
7+
8+
17239ZE1000
9
17410ZE2020
12
90325044000
13
90009ZE2003
14
9405006000
15
17235ZE2820
PART NAME
QTY.
REMARKS
PACKING, ELBOW
1
ELEMENT,AIR CLEANER(DUAL) .............. 1 ...................... INCLUDES ITEM W/
*
FILTER, OUTER
1
COVER, AIR CLEANER
1
GROMET,AIR CLEANER
1
COLLAR,AIR CLEANER
2
COLLAR(B),AIR CLEANER
1
ELBOW COMP.,AIR CLEANER ................ 1 ...................... INCLUDES ITEM W/+
NUT
1
BOLT-WASHER 6X22
1
FLANGE NUT 6MM
2
NOSE, SILENCER
1
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 47
GX270K1-SMX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 48 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
PART NO.
1
14100ZE3020
2
14410ZE2013
3
14431ZE2010
4
14441ZE2000
5
14451ZE1013
6
14568ZE1000
*
7
14711ZE2000
8
14721ZE2000
9
14751ZE2003
10
14771ZE2000
11
14773ZE2000
12
14781ZE2000
13
14791ZE2010
14
90012ZE0010
15
90206ZE1000
16
12209ZE8003
PART NAME
QTY.
REMARKS
CAMSHAFT ASSY .................................... 1 ...................... INCLUDES ITEM W/
*
ROD,PUSH
2
ARM,VALVE ROCKER
2
LIFTER,VALVE
2
PIBOT,ROCKER ARM
2
SPRING,WEIGHT RETURN
1
VALVE, IN.
1
VALVE, EX.
1
SPRING,VALVE
2
RETAINER,IN.VALVE SPRING
1
RETAINER,EX.VALVE SPRING
1
ROTATOR,VALVE
1
PLATE,PUSH ROD GUIDE
1
PIBOT BOLT 8MM
2
NUT,PIBOT ADJUSTING
2
SEAL, VALVE STEM
1
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 49
GX270K1-SMX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 50 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
1 % 16010ZE2812
* 16011ZA0931
2
*
16013ZA0931
3
*
5
* 16015ZE8005
8
* 16028ZE0005
9
16044ZE2005
*
10
16100ZH9W21
11
16124ZE0005
* 16166ZH9W20
13
* 16173001004
14
* 16211ZE2000
15
16
16220ZA0702
17
16221ZA0800
18
16223ZA0800
19
16610ZE1000
20
16953ZE1812
21
16954ZE1812
* 16956ZE1811
23
* 16957ZE1812
24
* 16967ZE0811
25
* 93500030061H
26
* 9430520122
27+
28
* 99101ZH80800
29
* 99204ZE20400
30
16016ZH7W01
*
31 % 16024ZE1811
* 16172ZE3W10
32
*
PART NAME
QTY.
REMARKS
GASKET SET
1
VALVE SET,FLOAT
1
FLOAT SET
1
CHAMBER SET,FLOAT ............................. 1 ...................... INCLUDES ITEM W/%
SCREW SET
1
CHOKE SET
1
CARBURETOR ASSY. (BE75B) ................ 1 ...................... INCLUDES ITEM W/
*
SCREW, THROTTLE STOP
1
NOZZLE, MAINE
1
PACKING,CUP
1
INSULATOR, CARBURETOR
1
SPACER COMP.,CARBURETOR
1
PACKING, CARBURETOR
1
PACKING, INSULATOR
1
CHOKE LEVER COMP. ............................. 1 ...................... INCLUDES ITEM W/+
LEVER,COCK
1
PLATE,LEVER SETTING
1
SPRING,COCK LEVER
1
PACKING,FUEL COCK
1
CUP,FUEL STRAINER
1
SCREW 3X6
2
SPRING PIN 2X12
1
JET, MAIN, #80
1
JET SET,PILOT, #40
1
SCREW SET
1
DRAIN SCREW SET
1
COLLAR SET
1
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 51
GX270K1-SMX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
PAGE 52 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO.
PART NO.
1
16551ZE2000
2
16555ZE2000
3
16561ZE2000
4
16562ZE2000
6
16570ZE2W10
10
* 16571ZE2W00
16574ZE1000
11
*
12
* 16575ZE2W00
16576891000
13
*
15
* 16578ZE1000
16
* 16581ZE2W00
17
16584883300
*
19
* 16592883310
20
* 16594883010
24
90013883000
25
90015ZE5010
27
90114SA0000
* 90605230000
28
* 93500040060H
30
* 93500050280A
32
* 93500050160A
33
* 9405006000
35
PART NAME
QTY.
REMARKS
ARM, GOVERNOR
1
ROD, GOVERNOR
1
SPRING, GOVERNOR
1
SPRING, THROTTLE RETURN
1
CONTROL ASSY.(REMOTE) ..................... 1 ...................... INCLUDES ITEM W/
*
LEVER, CONTROL
1
LEVER SPRING
1
WASHER,CONTROL LEVER
1
HOLDER,CABLE
1
SPACER,CONTROL LEVER
1
BASE COMP.,CONTROL
1
ADJUSTING SPRING
1
SPRING,CABLE RETURN
1
HOLDER, WIRE
1
FLANGE BOLT 6X12
2
BOLT, GOVERNOR ARM
1
LOCK NUT 6MM
1
CIR CLIP
1
SCREW 4X6
1
SCREW, PAN 5X28
1
SCREW 5X16
1
FLANGE NUT 6MM
1
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 53
GX270K1-SMX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 54 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO.
PART NO.
2
11300ZH9S50
3
11381ZE2801
4
15600735003
6
15600ZG4003
8%
15625ZE1003
9
16510ZE2000
*
10 + 16511ZE2000
*
11 + 16512ZE2000
*
12 + 16513ZE2000
* 16531Z0A000
13
* 90602ZE1000
15
* 90701HC4000
16
17
* 91201890003
18
9410106800
*
19
957010803500
20
961006206000
*
PART NAME
QTY.
REMARKS
COVER ASSY., CRANKCASE .................. 1 ...................... INCULDES ITEM W/
*
PACKINNG,CASE COVER
1
CAP ASSY.,OIL FILLER ........................... 1 ...................... INCLUDES ITEM W/%
OIL PLUG .................................................. 1 ...................... INCLUDES ITEM W/%
PACKING, OIL FILLER CAP
2
GOVERNOR ASSY. ................................... 1 ...................... INCLUDES ITEM W/+
WEIGHT, GOVERNOR
2
HOLDER, GOVERNOR WEIGHT
1
PIN,GOVERNOR WEIGHT
2
SLIDER, GOVERNOR
1
CLIP, GOVERNOR HOLDER
1
PIN,DOWEL 8X12
2
OIL SEAL, 30X46X8
1
PLAIN WASHER 6MM
1
FLANGE BOLT 8X35
7
BALL BEARING 6206
1
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 55
GX270K1-SMX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 56 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
PART NO.
1
13310ZH9000
9
92101080250A
11
90534706010
12
951400110
13
91001ZH9003
*
PART NAME
QTY.
REMARKS
CRANK SHAFT COMP. ............................. 1 ...................... INCULDES ITEM W/
*
BOLT 8X25
1
WASHER,LOCK 8MM
1
KEY 7X7X35
1
BEARING, BALL (6206 SH)
1
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 57
GX270K1-SMX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 58 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
PART NO.
1
12000ZH9406
2
15510ZE2043
3
16541ZE2010
6
90131883000
7
90446KE1000
9
91201890003
*
10
91353671004
11
9405010000
12
9410912000
13
9425110000
14
957010601200
16
34150ZH7003
17
90013883000
19
90131ZE3790
20
9280012000
PART NAME
QTY.
REMARKS
BARREL ASSY.,CYLINDER ...................... 1 ...................... INCULDES ITEM W/
*
SWITCH ASSY,OIL LEVEL
1
SHAFT,GOVERNOR ARM
1
BOLT,DRAIN PLUG
2
WASHER 8.2X17X0.8
1
OIL SEAL, 30X46X8
1
O-RING 14MM
1
FLANGE NUT M10
1
WASHER,DRAIN PLUG M12
2
PIN,LOCK 10MM
1
FLANGE BOLT 6X12
2
ALERT UNIT, OIL
1
FLANGE BOLT 6X12
1
DRAIN JOINT
1
BOLT, DRAIN PLUG 12MM
1
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 59
GX270K1-SMX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 60 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
PART NO.
1
12200ZH9000
2
* 12204ZE2306
3
* 12205ZE2305
4
12216ZE2300
*
5
12251ZH9000
6
12310ZE2020
7
950051110030
8
12391ZE2020
9
14775ZE2010
11
90014ZE2000
12
90042ZE2000
13
92900080320E
14
90441ZE2010
15
9430112200
16
957251008000
17
9807955846
PART NAME
QTY.
REMARKS
HEAD COMP.,CYLINDER ......................... 1 ...................... INCULDES ITEM W/
*
GUIDE,IN.VALVE(OVERSIZE)
1
GUIDE,EX.VALVE(OVERSIZE)
1
CLIP,VALVE GUIDE
1
GASKET, CYLINDER HEAD
1
COVER COMP.,HEAD
1
TUBE,11X100
1
PACKING,HEAD COVER
1
SEAT,VALVE SPRING
1
BOLT,HEAD COVER
1
BOLT,STUD 8X123
2
BOLT,STUD 8X32
2
WASHER COMP.,HEAD COVER
1
PIN,DOWEL 12X20
2
BOLT,FLANGE 10X80
4
PLUG, SPARK (BPR5ES)
1
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 61
GX270K1-SMX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 62 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO.
PART NO.
3
16731ZE2003
5
19610ZE2010ZC
7
19631ZE2D00
11
36100ZH7003
17
90013883000
18
90013883000
22
90684ZA0601
PART NAME
CLIP,TUBE
COVER COMP.,FAN /BLACK
SHROUD
STOP SWITCH ASSY.
FLANGE BOLT 6X12
FLANGE BOLT 6X12
CLIP, HARNESS
QTY.
1
1
1
1
5
1
1
REMARKS
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 63
GX270K1-SMX2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 64 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
PART NO.
1
19511ZE2000
4
28451ZE2W01
5
31100ZE2010
8
90201ZE3V00
9
90741ZE2000
PART NAME
FAN, COOLING
PULLEY, STARTER
FLYWHEEL COMP.
NUT,SPECIAL 16MM
KEY,SPECIAL WOODRUFF25X18
QTY.
1
1
1
1
1
REMARKS
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 65
GX270K1-SMX2 ENGINE — FUEL TANK ASSY.
FUEL TANK ASSY.
PAGE 66 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — FUEL TANK ASSY.
FUEL TANK ASSY.
NO.
PART NO.
1
16854ZH8000
2
16955ZE1000
5
17510ZE2020ZD
7
17620Z0T814
9
17672ZE2W01
12
91353671004
14
9405008000
15
950014522240
16
9500202080
17
957010802500
22
17631Z0T812
*
PART NAME
QTY.
REMARKS
RUBBER,SUPPORT(107MM)
1
JOINT,FUEL TANK
1
TANK COMP., FUEL NH1
1
CAP COMP., FUEL FILLER ...................... 1 ...................... INCLUDES ITEM W/
*
FUEL FILTER
1
O-RING 14MM
1
FLANGE NUT M8
2
TUBE, FUEEL 4.5X222
1
CLIP, TUBE
2
FLANGE BOLT 8X25
2
PAKING, FUEL FILLER CAP
1
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 67
GX270K1-SMX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 68 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO.
PART NO.
1
30500-ZF6-W02
4
30700-ZE1-013
8
31512-ZE2-000
10
36101-ZE1-010
13
90015-883-000
PART NAME
COIL AY,IGNITION/GX390
CAP ASSY.
GROMMET,CORD
CORD,STOP SWITCH 370MM
FLANGE BOLT 6X28
QTY.
1
1
1
1
1
REMARKS
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 69
GX270K1-SMX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 70 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO.
PART NO.
2
18310ZE2W00
3
18320ZE2W01
4
18323ZE2W00
5
18330ZE2W00
7
18333ZE3800
8
18355ZE2010
9
18381ZE2W10
18
90013883000
19
90050ZE1000
26
9405008000
29
90050ZE1000
PART NAME
MUFFLER COMP.
PROTECTOR COMP.,MUFFLER
PROTECTOR, EXHAUST PIPE
PIPE,EXHAUST
GASKET
ARRESTER, SPARK
GASKET,MUFFLER(ARRESTER)
FLANGE BOLT 6X12
TAPPING SCREW 5X8
FLANGE NUT M8
TAPPING SCREW 5X8
QTY.
1
1
1
1
1
1
1
1
6
3
1
REMARKS
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 71
GX270K1-SMX2 ENGINE — PISTON ASSY.
PISTON ASSY.
PAGE 72 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — PISTON ASSY.
PISTON ASSY.
NO.
PART NO.
1
13010ZE8601
2
13101ZH9000
3
13111ZE2000
4
13200E2010
5
90001E8000
* 90551E1000
6
PART NAME
QTY.
REMARKS
RING SET, PISTON (STD)
1
PISTON (STD)
1
PIN ,PISTON
1
ROD ASSY., CONNECTING (STD) ........... 1 ...................... INCLUDES ITEM W/
*
BOLT, CONNECTING ROD
2
CLIP, PISTON PIN 18MM
2
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 73
GX270K1-SMX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 74 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
PART NO.
1
28400ZE2W01ZB
2
* 28410ZE2W01ZB
3
* 28421ZE2W01
4
* 28422ZE2W01
5
28441ZE2W01
*
6
* 28442ZE2W01
7
* 28443ZE2W01
28444ZE2W01
8
*
10
* 28461ZE2W02
11
* 28462ZE2W11
13
* 90004ZE2W01
14
90008ZE2003
PART NAME
QTY.
REMARKS
RECOIL STARTER AY/GX240,B ............... 1 .....................INCLUDES ITEM W/
*
CASE COMP.,RECOIL STARTER
1
PULLEY,RECOIL STARTER
1
RATCHET,STARTER
2
SPRING,FRICTION
1
SPRING,STARTER RETURN
1
SPRING,RATCHET
2
RETAINER,SPRING
1
GRIP,STARTER
1
ROPE, RECOIL STARTER
1
SCREW,CENTER
1
BOLT,FLANGE 6X10
3
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 75
GX270K1-SMX2 ENGINE — LABELS ASSY.
LABELS ASSY.
PAGE 76 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
GX270K1-SMX2 ENGINE — LABELS ASSY.
LABELS ASSY.
NO.
PART NO.
3
87521ZH9030
7
87522ZH9010
10
87528ZE2810
17
87532ZH8810
PART NAME
EMBLEM
RABEL /GX120K1
MARK,CHOKE(ORANGE)
LABEL
QTY.
1
1
1
1
REMARKS
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 77
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5.
Parts must be in new and resalable condition, in the original Multiquip package (if
any), and with Multiquip part numbers
clearly marked.
6.
The following items are not returnable:
Terms of payment for parts are net 30 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a signed
manifest has been obtained from the carrier,
and any claim for shortage or damage must be
settled between the consignee and the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being replaced by another item, it is obsolete.)
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were purchased more than six months prior to
the return date.
MINIMUM ORDER
Multiquip reserves the right to quote and sell
direct to Government agencies, and to Original
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the invoice
for special handling including bus shipments,
insured parcel post or in cases where Multiquip
must personally deliver the parts to the carrier.
LIMITATIONS OF SELLER’S LIABILITY
RETURNED GOODS POLICY
d. Special order items.
Return shipments will be accepted and credit
will be allowed, subject to the following provisions:
e. Electrical components.
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of the
item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental damages.
f. Paint, chemicals, and lubricants.
LIMITATION OF WARRANTIES
g. Decals and paper products.
1.
h. Items purchased in kits.
No warranties, express or implied, are made
in connection with the sale of parts or trade
accessories nor as to any engine not manufactured by Multiquip. Such warranties made in
connection with the sale of new, complete units
are made exclusively by a statement of warranty packaged with such units, and Multiquip
neither assumes nor authorizes any person to
assume for it any other obligation or liability
whatever in connection with the sale of its
products. Apart from such written statement of
warranty, there are no warranties, express,
implied or statutory, which extend beyond the
description of the products on the face hereof.
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
2.
A Returned Material Authorization must
be approved by Multiquip prior to shipment.
To obtain a Return Material Authorization,
a list must be provided to Multiquip Parts
Sales that defines item numbers, quantities, and descriptions of the items to be
returned.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
c. The list must state the reason(s) for
the return.
d. The list must reference the sales
order(s) or invoice(s) under which the
items were originally purchased.
e. The list must include the name and
phone number of the person requesting the RMA.
3.
A copy of the Return Material Authorization must accompany the return shipment.
4.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
c. Any line item with an extended dealer
net price of less than $5.00.
7.
The sender will be notified of any material
received that is not acceptable.
8.
Such material will be held for five working
days from notification, pending instructions. If a reply is not received within five
days, the material will be returned to the
sender at his expense.
9.
Credit on returned parts will be issued at
dealer net price at time of the original
purchase, less a 15% restocking charge.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
Effective: February 22, 2006
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a specific date and all orders received on or after that
date will be billed at the revised price. Rebates
for price declines and added charges for price
increases will not be made for stock on hand
at the time of any price change.
PAGE 78 — MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07)
NOTES
MVH-306GH PLATE COMPACTOR — OPERATION AND PARTS MANUAL — REV. #4 (08/15/07) — PAGE 79
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Tel. (800) 421-1244
Carson, CA 90746
Fax (800) 537-3927
Contact: [email protected]
Mayco Parts
800-306-2926
Fax: 800-672-7877
310-537-3700
Fax: 310-637-3284
Service Department
800-421-1244
Fax: 310-537-4259
310-537-3700
MQ Parts Department
800-427-1244
310-537-3700
MEXICO
UNITED KINGDOM
MQ Cipsa
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: [email protected]
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Fax: 800-672-7877
Fax: 310-637-3284
Warranty Department
800-421-1244, Ext. 279 Fax: 310-537-1173
310-537-3700, Ext. 279
Technial Assistance
800-478-1244
Fax: 310-631-5032
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Lancashire OL7 0TL
Contact: [email protected]
Tel: 0161 339 2223
Fax: 0161 339 3226
CANADA
BRAZIL
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Multiquip
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055
Barra de Tijuca - Rio de Janeiro
Fax: 011-55-21-3433-9055
Contact: [email protected], [email protected]
Tel: (450) 625-2244
Fax: (450) 625-8664
© COPYRIGHT 2007, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data
contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or
the information published in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is:
manufactured for Multiquip Inc.
by
MIKASA SANGYO CO., LTD. Tokyo, Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement