H&R Pump Shotgun

H&R Pump Shotgun
Owner's Manual
New England Firearms
®
Pardner Pump
®
A
B
SAFE Position
FIRE Position
How to Operate the Safety
This manual contains operating, care and maintenance instructions. To assure safe operation, any user of this firearm must
read this manual carefully. Failure to follow the instructions and
warnings in this manual can cause accidents resulting in injury
or death. This manual should always accompany this firearm,
and be transferred with it upon change of ownership.
WARNING: KEEP THIS FIREARM OUT OF THE REACH OF
CHILDREN, UNAUTHORIZED INDIVIDUALS, AND OTHERS
UNFAMILIAR WITH THE SAFE HANDLING OF FIREARMS.
• WARNING: Before installing the barrel, become thoroughly familiar
with the operation of the safety.
The safety mechanism is a round button located behind the trigger. To
put your shotgun on SAFE, hold it in the normal shooting position,
pointed in a safe direction, and push the safety button from left to right
as far as it will go. The safety is now on SAFE (See A). To move your
safety to the FIRE position, push the safety button from right to left as
far as it will go. A red ring will appear on the left side of the safety button when it is in the FIRE position (See B). If the trigger is pulled with
the safety in this position, the gun will fire.
• WARNING: The safety has been correctly designed and tested. Any
mechanical device can fail, however, so never rely on the safety to
justify careless handling.
Before You Use This Firearm
How to Install the Barrel
It is very important that you read and understand this manual before
using this firearm. Warnings should be read and heeded carefully.
Look through the barrel to be sure it is free of grease, oil or any other
obstruction.
With the safety on SAFE, press the slide lock release lever (See C),
and open the action approximately half way.
IMPORTANT
• WARNING: It is a violation of federal law to alter or deface the
serial number of any firearm.
How Your Shotgun is Made
Your new shotgun has been made to H&R 1871, LLC’s strictest standards of safety and reliability. It has been tested using proof and service ammunition that meets Sporting Arms & Ammunition
Manufacturers Institute (SAAMI) & American National Standards
Institute (ANSI) performance standards.
Your New Pump Shotgun
• 12-gauge, 3" chamber. Designed to handle 23⁄4" and 3" shells
interchangeably.
• 12-gauge, 31⁄2" chamber. Designed to handle 23⁄4", 3" and 31⁄2"
shells interchangeably.
• 20-gauge, 3" chamber. Designed to handle 23⁄4" and 3" shells
interchangeably.
Your shotgun will function with factory-loaded ammunition of any
shot size, as well as rifled slugs and sabots.
The barrel is equipped with an internal modified choke tube. It can be
removed or tightened with a quarter-size coin. (Be sure it is tight
before firing.) Additional choke tubes (Winchester/Browning/
Mossberg-type) can be purchased from a gun shop.
• WARNING: Except for installation of the barrel, your gun was
shipped fully assembled. It should not be used or disassembled
without reading and understanding the instructions in this manual.
C
D
Press slide lock release
E
Installing barrel
Removing
magazine cap
• WARNING: Do not fully cycle the
action, as this can cause the ejector
F
to break.
Remove the magazine cap (See D).
BOLT
BARREL
Install the barrel (See E), being sure
to mate the aligning tab in the receiv- Aligning receiver and barrel
er with the corresponding cut in the
barrel (See F). Be sure the barrel is firmly seated in the receiver, and
replace the magazine cap while pushing rearward on the barrel.
How to Load
NOTE: Your shotgun was shipped with a 2-shot plug installed, which is
required when hunting migratory waterfowl. If you want to remove it, see
the section of this manual entitled “How to Remove the Magazine Plug.”
• WARNING: Before loading, always check the bore to be sure it is free
of grease, oil or any other obstruction, and the safety in on SAFE.
Loading the Magazine
Before loading, be sure that: 1) the gun is pointed in a safe direction, 2)
the safety is on SAFE, 3) the chamber is empty, and 4) the bolt is closed.
H
G
Loading the magazine
Shells must pass shell stop
Load up to two 23⁄4" or 3" shells (assuming the magazine plug is
installed), by pushing them (crimped end toward the muzzle) into the
magazine loading port (See G). Be sure each shell passes beyond the
shell stop (See H).
Loading the Chamber
Press the slide lock release lever (See C) and pump the action all the
way back and all the way forward one time. Load one more shell into the
magazine (See G).
Loading a Single Shell
With the action all the way open, place a single shell directly into the
chamber, and close the action.
• WARNING: When either of the above loading procedures is finished,
your shotgun is cocked and ready to fire as soon as the safety is pushed
to the FIRE position.
How to Fire
With the gun pointed at the target, push the safety to the FIRE position
and squeeze the trigger.
After firing, pull the forearm all the way back to eject the fired shell, and
push the forearm all the way forward to chamber the next shell.
If you do not fire all shells at the target, be sure to put the safety on SAFE
until you are ready to shoot again.
How to Unload
• WARNING: Before unloading, be sure the safety is on SAFE and your
gun is pointed in a safe direction.
Step #1. Push the slide lock release lever and open the action slowly
until the front of the shell is visible in the ejection port. Lift the front of
the shell outward and remove the shell from the ejection port.
Step #2. Continue to pull the forearm back until the next shell is
released from the magazine.
Step #3. Tip the gun sideways so that the shell drops from the ejection port.
Step #4. Push slide lock release and work the action in this manner until all
shells have been removed.
Step #5. Check action and magazine to make sure no shells remain.
What to do if Your Shotgun Fails to Fire
1. Underpowered Shot. A “squib” or underpowered shot should not
occur if the ammunition is clean, dry and factory-loaded. You can tell if a
shot is underpowered by the unusually low report it makes.
• WARNING: Because wads, shot protector or lead may still be in the
barrel, you must unload completely and, with the action open, and the
safety on SAFE, look through the barrel to see if there is any obstruction. If there is, it must be removed before shooting the gun again.
2. Misfire. If you squeeze the trigger and the shell does not fire, remain
in shooting position and count to 10. Then operate the action to eject
the misfired shell.
How to Remove the Magazine Plug
Step #1. With the gun empty, the safety on SAFE, and the gun pointed
in a safe direction, press the slide lock release lever and pull the forearm half way back.
Step #2. Remove the magazine cap (See D) and reverse step E.
Step #3. Insert your index finger into the slotted magazine spring retainer
(See I). Push the magazine spring retainer into the magazine about 11⁄2" .
Step #4. Turn the retainer 90° and slowly release it out the front of
the tube (See I).
• WARNING: Wear eye
protection and use caution when removing the
retainer as it is under
tension from the magazine spring.
Step #5. Remove the
retainer and plug, and
separate them (See J).
Step #6. Place the
retainer on the end of
the magazine spring,
line up the detents on
I
Magazine
Spring
Retainer
Magazine
Tube
Insert index finger into retainer and turn 90°
Magazine Spring
J
Magazine Tube
Magazine Spring Retainer
Magazine Plug
Remove retainer and plug
the retainer with the detents on the magazine, and
reverse the removal process (See K).
Step #7. Release the retainer slowly to be sure it
is securely seated.
Step #8. Replace the barrel and tighten the magazine cap (See D and E).
Your shotgun now has a magazine capacity of five.
How to Clean Your Shotgun
• WARNING: Your shotgun should be completely
K
unloaded and on SAFE while cleaning.
Remove the barrel as described previously. Clean
the bore from the breech end, using any standard Line up detents
12 gauge cleaning rod, brush, and patches with and replace retainer
powder solvent.
You do not need to clean the action under normal conditions, and
further disassembly is not recommended.
• WARNING: Never attempt to wipe down or clean a loaded gun.
Avoid the use of oil during below freezing conditions. A dry graphite used
sparingly is recommended for cold weather lubrication. Condensation
droplets may form soon after the gun is brought into a warm room, or it
may become wet during inclement weather. In any case, all moisture
should be removed. Exterior metal finishes may be wiped down with a
slightly oiled cloth. For long term storage, lightly oil the bore, barrel and
action with gun oil. Your gun should be completely unloaded and stored
in a dry area. Never store your gun in a carrying case.
• WARNING: We specifically disclaim responsibility for any damage or
injury occurring in connection with, or as the result of, the use, in any
H&R manufactured or distributed firearm, of faulty, non-standard,
“remanufactured”, or handloaded (reloaded) ammunition.
Guide to Firearm Safety
1. Read and understand the owner’s manual before using a firearm.
2. If you are unfamiliar with firearms, attend a firearms safety class taught
by a certified instructor.
3. Handle every firearm as if it were loaded and ready to fire.
4. Control the muzzle, and never point a firearm at anything you don’t
want to shoot.
5. Keep the safety on SAFE until you are ready to shoot.
6. Unless you are hunting, carry your firearm empty, with the action open.
7. Before shooting, be sure you have an adequate backstop. All ammunition
is dangerous beyond your line of sight.
8. Avoid ricochets by never shooting at water or any hard, flat surface.
9. Do not run, climb, or jump over an obstacle with a loaded firearm.
10. Do not climb into or out of a tree or tree stand with a loaded firearm.
Do not allow others to pass loaded firearms to you while in a tree stand.
11. Do not enter or ride in a motor vehicle with loaded firearms.
12. Do not lean a loaded firearm against anything.
13. Do not bump, drop or jar a loaded firearm.
14. Do not pull a firearm toward you by the muzzle.
15. Wear hearing protectors when shooting.
16. Wear impact-protective glasses when shooting, disassembling or
cleaning firearms.
17. Avoid alcoholic beverages and drugs before and during shooting.
18. Use only ammunition of the correct gauge, caliber, size and bullet shape
for your firearm.
19. Do not use damaged, dirty, modified, or improperly handloaded
ammunition.
20. Keep the barrel and mechanism of the firearm free of obstructions.
21. Do not use a firearm that fails to function properly. Do not try to force a
jammed action.
22. Be sure no one is in the path of ejecting shells or cartridges.
23. Do not interchange parts between firearms, and be sure disassembly
and reassembly are correct and complete.
24. Before cleaning, be sure the chamber, action and magazine are
completely unloaded.
25. Unload firearms before storing, transporting, or leaving unattended.
26. Store firearms and ammunition separately, locked and out of the
reach of children.
Failure to follow these rules, or other instructions in this manual, can result in
personal injury or death.
LIMITED WARRANTY
H&R 1871, LLC
TWO YEAR LIMITED WARRANTY AGAINST
DEFECTS IN MATERIAL & WORKMANSHIP
This firearm warranty is good only to the ORIGINAL OWNER who has registered his
ownership with H&R 1871, LLC at 60 Industrial Rowe, Gardner, MA.
WARRANTY and CERTIFICATE OF OWNERSHIP card must be completed and mailed
to H&R 1871 at the above address WITHIN TEN (10) DAYS of purchase to insure the
protection of the warranty. NOTICE of defect in materials and/or workmanship must
be received by the company WITHIN TWO (2) YEARS from the date of purchase.
®
Normal wear, or damage resulting from neglect, abuse, alteration, or repairs not
made or authorized by H&R 1871 or use of non-H&R parts are not covered by the warranty.
®
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
H&R 1871, LLC’S PERFORMANCE UNDER THE ABOVE WARRANTY
1. After notice of defect in material and/or workmanship is received by H&R 1871, LLC, H&R shall send instructions for shipment of the firearm; and repairs will be made and the firearm returned within a reasonable time
after the firearm is received. Cost of shipping, insurance charges, etc. involved in returning the firearm to the
company shall be prepaid by the original owner.
2. Cost of parts and labor performed shall be provided without charge by H&R 1871 .
3. If H&R 1871 , after receipt of the firearm, determines that the defects in material and/or workmanship were
the result of abuse and/or neglect, or otherwise not covered by the warranty set forth above, H&R shall notify
such owner to that effect and give an estimate for repair. In such cases, repair, return shipping and insurance
charges, etc. shall be paid by such owner.
4. In the event that H&R 1871 is unable to make warranty repairs to the firearm, it shall, within a reasonable
time after its receipt, notify the owner to that effect and give him the option either to receive a replacement of
the same model, if then available in its inventory, or to receive a refund, either of which, if feasible, will be
made through the store of purchase.
®
®
®
H&R 1871, LLC • 60 Industrial Rowe • Gardner, MA 01440 U.S.A. • www.hr1871.com
WARNING
Children are attracted to and can operate firearms
that can cause severe injuries or death.
Prevent child access by always keeping guns locked
away and unloaded when not in use. If you keep a loaded
firearm where a child obtains and improperly uses it, you
may be fined or sent to prison.
ADVERTENCIA
Health Warning: Discharging of firearms in poorly ventilated areas and
handling ammunition may cause exposure to lead and/or lead compounds. Exposure may cause cancer, birth defects or damage to the
kidney, nervous, blood forming and reproductive systems. Have adequate ventilation at all times, especially in confined areas. Wash hands
thoroughly after shooting, handling ammunition, or cleaning a firearm.
Do not eat or smoke during these activities.
Safety Warning: We strongly recommend that you take a hunter safety
course, taught by a certified instructor, before you use this firearm. Your
State Fish & Game Department or a local gun shop can suggest courses
in your area.
Safety Warning: Keep this firearm out of the reach of children, unauthorized individuals, and others unfamiliar with the safe handling of firearms.
A los niños los atraen las armas de fuego y las pueden
hacer funcionar. Ellos pueden causarses lesiones graves
y la muerte.
Evite que los niños tengan acceso a las armas de fuego
guardándolas siempre con llave y descargadas cuando no
las esté utilizando. Si usted tiene un arma de fuego cargada
en un lugar en que un niño tiene acceso a ella y la usa indebidamente, le pueden dar una multa o enviarlo a la carcel.
Manufactured for: H&R 1871, LLC
60 Industrial Rowe, Gardner, MA 01440 U.S.A.
www.hr1871.com
Part # S03105
7/06
Pardner® Pump Shotgun
12 Gauge • 20 Gauge
Youth • Slug • 3" Chamber
* Restricted availabilityPart sent to qualified
gunsmith only.
** Restricted availabilityParts installed at factory only.
*** Non-restricted availabilityPart may require some final
fitting sanding or filing.
ILL. NO.
**1
2
3
*4
5
6
7
8
*9
**10
11
12
13
14
15
**16
17
18
19
**20
21
**22
23
24
25
26
**27
28
29
30
31
32
PART NAME
. . . . . . . . . . . . . .BARREL ASSEMBLY
. . . . . . . . . . . . . .SIGHT-BEAD
. . . . . . . . . . . . . .CHOKE
. . . . . . . . . . . . . .RECEIVER & MAGAZINE TUBE ASS'Y.
. . . . . . . . . . . . . .LATCH-RIGHT SHELL
. . . . . . . . . . . . . .LATCH-LEFT SHELL
. . . . . . . . . . . . . .PIN-REAR TRIGGER GUARD
. . . . . . . . . . . . . .PIN-FRONT TRIGGER GUARD
. . . . . . . . . . . . . .SPRING-EJECTOR
. . . . . . . . . . . . . .CARRIER
. . . . . . . . . . . . . .MAGAZINE FOLLOWER
. . . . . . . . . . . . . .MAGAZINE SPRING
. . . . . . . . . . . . . .MAGAZINE PLUG
. . . . . . . . . . . . . .RETAINER-MAGAZINE SPRING
. . . . . . . . . . . . . .ACTION BAR ASSEMBLY
. . . . . . . . . . . . . .FOREND
. . . . . . . . . . . . . .NUT-FOREND TUBE
. . . . . . . . . . . . . .MAGAZINE CAP
. . . . . . . . . . . . . .BOLT-BREECH
. . . . . . . . . . . . . .LOCKING BLOCK
. . . . . . . . . . . . . .SLIDE ASSEMBLY
. . . . . . . . . . . . . .PIN-FIRING
. . . . . . . . . . . . . .SPRING-FIRING PIN RETRACTOR
. . . . . . . . . . . . . .PIN-FIRING PIN RETAINING
. . . . . . . . . . . . . .PLUNGER-EXTRACTOR
. . . . . . . . . . . . . .SPRING-EXTRACTOR
. . . . . . . . . . . . . .EXTRACTOR
. . . . . . . . . . . . . .TRIGGER PLATE PARTS ASSY. (SEE FIGURE #2)
. . . . . . . . . . . . . .STOCK BEARING PLATE
. . . . . . . . . . . . . .STOCK ASS'Y.
. . . . . . . . . . . . . .BOLT-STOCK
. . . . . . . . . . . . . .WASHER-STOCK BOLT
ILL. NO.
33
34
35
36
37
38
**39
40
**41
**42
43
**44
**45
**46
**47
**48
49
50
51
**52
**53
**54
**55
56
57
58
59
**60
**61
62
63
PART NAME
. . . . . . . . . . . . . .PAD-RECOIL
. . . . . . . . . . . . . .SCREW-RECOIL PAD
. . . . . . . . . . . . . .PLUG-RECOIL PAD SCREW
. . . . . . . . . . . . . .RECEIVER STUD
. . . . . . . . . . . . . .HAMMER PIVOT PIN WASHER
. . . . . . . . . . . . . .N/A
. . . . . . . . . . . . . .LOCK-ACTION BAR
. . . . . . . . . . . . . .SPRING-ACTION BAR LOCK
. . . . . . . . . . . . . .DOG-CARRIER
. . . . . . . . . . . . . .TRIGGER PLATE
. . . . . . . . . . . . . .TRIGGER ASSEMBLY
. . . . . . . . . . . . . .HAMMER
. . . . . . . . . . . . . .FOLLOWER-CARRIER DOG
. . . . . . . . . . . . . .SPRING-CARRIER DOG FOLLOWER
. . . . . . . . . . . . . .PIN-CARRIER DOG
. . . . . . . . . . . . . .TUBE-CARRIER PIVOT
. . . . . . . . . . . . . .PIN-HAMMER PIVOT
. . . . . . . . . . . . . .PLUNGER-HAMMER
. . . . . . . . . . . . . .SPRING-HAMMER
. . . . . . . . . . . . . .BUTTON-SAFETY
. . . . . . . . . . . . . .BALL-SAFETY DETENT
. . . . . . . . . . . . . .SPRING-SAFETY DETENT
. . . . . . . . . . . . . .SEAR
. . . . . . . . . . . . . .PIN-TRIGGER
. . . . . . . . . . . . . .BUSHING-REAR TRIGGER PLATE PIN
. . . . . . . . . . . . . .SPRING-FRT. TRIG. PLATE PIN DETENT
. . . . . . . . . . . . . .SPRING-REAR TRIG. PLATE PIN DETENT
. . . . . . . . . . . . . .CARRIER DOG WASHER
. . . . . . . . . . . . . .SAFETY SWITCH SPRING RETAINING PIN
. . . . . . . . . . . . . .SEAR PIN
. . . . . . . . . . . . . .SPRING-SEAR
2/07
S03897
BARREL ASSEMBLY
SIGHT-BEAD
CHOKE
RECEIVER & MAGAZINE TUBE ASS'Y.
LATCH-RIGHT SHELL
LATCH-LEFT SHELL
PIN-REAR TRIGGER GUARD
PIN-FRONT TRIGGER GUARD
SPRING-EJECTOR
CARRIER
MAGAZINE FOLLOWER
MAGAZINE SPRING
MAGAZINE PLUG
RETAINER-MAGAZINE SPRING
ACTION BAR ASSEMBLY
FOREND-CYL. PUMP-BLACK WALNUT
FOREND-PUMP SYN. BLACK
FOREND-PUMP SYN. MOSSY
NUT-FOREND TUBE
MAGAZINE CAP
MAGAZINE CAP (WITH STUD)
BOLT-BREECH
LOCKING BLOCK
SLIDE ASSEMBLY
PIN-FIRING
SPRING-FIRING PIN RETRACTOR
PIN-FIRING PIN RETAINING
PLUNGER-EXTRACTOR
SPRING-EXTRACTOR
EXTRACTOR
TRIGGER PLATE PARTS ASSY.
STOCK BEARING PLATE
STOCK ASS'Y.-BLACK WALNUT
STOCK-PUMP SYN. BLACK
STOCK-PS SYN. MOSSY
BOLT-STOCK
WASHER-STOCK BOLT
PAD-RECOIL
SCREW-RECOIL PAD
PLUG-RECOIL PAD SCREW
RECEIVER STUD
HAMMER PIVOT PIN WASHER
N/A
LOCK-ACTION BAR
SPRING-ACTION BAR LOCK
DOG-CARRIER
TRIGGER PLATE
TRIGGER ASSEMBLY
HAMMER
FOLLOWER-CARRIER DOG
SPRING-CARRIER DOG FOLLOWER
PIN-CARRIER DOG
TUBE-CARRIER PIVOT
PIN-HAMMER PIVOT
PLUNGER-HAMMER
SPRING-HAMMER
BUTTON-SAFETY
BALL-SAFETY DETENT
SPRING-SAFETY DETENT
SEAR
PIN-TRIGGER
BUSHING-REAR TRIGGER PLATE PIN
SPRING-FRT. TRIG. PLATE PIN DETENT
SPRING-REAR TRIG. PLATE PIN DETENT
CARRIER DOG WASHER
SAFETY SWITCH SPRING RETAINING PIN
SEAR PIN
SPRING-SEAR
**1
2
3
*4
5
6
7
8
*9
**10
11
12
13
14
15
**16
**16
**16
17
18
18
19
**20
21
**22
23
24
25
26
**27
28
29
30
30
30
31
32
**33
34
35
36
37
38
**39
40
**41
**42
43
**44
**45
**46
**47
**48
49
50
51
**52
**53
**54
**55
56
57
58
59
**60
**61
62
63
ILL. NO. PART NAME
S03114
S03408
H12MOD
S12IMD
S03890
S03389
S03388
S03400
S03399
S03412
S03382
S03392
S03891
S03892
S03405
S03375
S03386
S03319
S03320
S03393
S03486
S03487
S03377
S03391
S03409
S03396
S03414
S03397
S03403
S03413
S03385
----------S03901
S03154
S03317
S03318
S03378
S03423
S03394
S03902
S03881
S03882
S03893
N/A
S03390
S03410
S03384
S03422
S03421
S03387
S03402
S03411
S03395
S03380
S03398
S03404
S03416
S03381
S03376
S03418
S03407
S03401
S03379
S03415
S03417
S03903
S03904
S03905
S03419
WALNUT
PUMP
NP1-228
12 GAUGE
S03890
S03389
S03388
S03400
S03399
S03412
S03382
S03392
S03891
S03892
S03405
S03375
S03386
S03319
S03320
S03393
S03486
S03487
S03377
S03391
S03409
S03396
S03414
S03397
S03403
S03413
S03385
----------S03901
S03154
S03317
S03318
S03378
S03423
S03394
S03902
S03881
S03882
S03893
N/A
S03390
S03410
S03384
S03422
S03421
S03387
S03402
S03411
S03395
S03380
S03398
S03404
S03416
S03381
S03376
S03418
S03407
S03401
S03379
S03415
S03417
S03903
S03904
S03905
S03419
S03713
S03408
S20IMD
WALNUT
PUMP
NP1-206
20 GAUGE
S03473
S03408
H12MOD
S12IMD
S03890
S03389
S03388
S03400
S03399
S03412
S03382
S03392
S03891
S03892
S03405
S03375
S03386
S03319
S03320
S03393
S03486
S03487
S03377
S03391
S03409
S03396
S03414
S03397
S03403
S03413
S03901
SEE
S03901
N/A
S03317
S03318
S03378
S03423
S03394
S03902
S03881
S03882
S03893
N/A
S03390
S03410
S03384
S03422
S03421
S03387
S03402
S03411
S03395
S03380
S03398
S03404
S03416
S03381
S03376
S03418
S03407
S03401
S03379
S03415
S03417
S03903
S03904
S03905
S03419
SYNTHETIC
PUMP
NP1-2S8
12 GAUGE
S03890
S03389
S03388
S03400
S03399
S03412
S03382
S03392
S03891
S03892
S03405
S03375
S03386
S03319
S03320
S03393
S03486
S03487
S03377
S03391
S03409
S03396
S03414
S03397
S03403
S03413
S03385
FIGURE
S03901
N/A
S03317
S03318
S03378
S03423
S03394
S03902
S03881
S03882
S03893
N/A
S03390
S03410
S03384
S03422
S03421
S03387
S03402
S03411
S03395
S03380
S03398
S03404
S03416
S03381
S03376
S03418
S03407
S03401
S03379
S03415
S03417
S03903
S03904
S03905
S03419
S03714
S03408
S20IMD
SYNTHETIC
PUMP
NP1-2S6
20 GAUGE
S03890
S03389
S03388
S03400
S03399
S03412
S03382
S03392
S03891
S03892
S03405
S03375
S03386
S03319
S03320
S03393
S03486
S03487
S03377
S03391
S03409
S03396
S03414
S03397
S03403
S03413
S03385
#2
S03901
S03154
S03317
S03318
S03378
S03423
S03394
S03902
S03881
S03882
S03893
N/A
S03390
S03410
S03384
S03422
S03421
S03387
S03402
S03411
S03395
S03380
S03398
S03404
S03416
S03381
S03376
S03418
S03407
S03401
S03379
S03415
S03417
S03903
S03904
S03905
S03419
S03708
S03408
S12IMD
CHAMBER
PUMP
NP1-235
12 GAUGE
S03890
S03389
S03388
S03400
S03399
S03412
S03382
S03392
S03891
S03892
S03405
S03375
S03386
S03319
S03320
S03393
S03486
S03487
S03377
S03391
S03409
S03396
S03414
S03397
S03403
S03413
S03385
----------S03901
S03154
S03317
S03318
S03378
S03423
S03394
S03902
S03881
S03882
S03893
N/A
S03390
S03410
S03384
S03422
S03421
S03387
S03402
S03411
S03395
S03380
S03398
S03404
S03416
S03381
S03376
S03418
S03407
S03401
S03379
S03415
S03417
S03903
S03904
S03905
S03419
S03712
S03408
S20IMD
PUMP
WALNUT
NP1-201
20 GAUGE
S03890
S03389
S03388
S03400
S03399
S03412
S03382
S03392
S03891
S03892
S03405
S03375
S03386
S03319
S03320
S03393
S03486
S03487
S03377
S03391
S03409
S03396
S03414
S03397
S03403
S03413
S03385
----------S03901
N/A
S03317
S03318
S03378
S03423
S03394
S03902
S03881
S03882
S03893
N/A
S03390
S03410
S03384
S03422
S03421
S03387
S03402
S03411
S03395
S03380
S03398
S03404
S03416
S03381
S03376
S03418
S03407
S03401
S03379
S03415
S03417
S03903
S03904
S03905
S03419
S03711
S03408
S20IMD
PUMP
SYNTHETIC
NP1-2S1
20 GAUGE
59
54
53
61
58
52
57
48
41
42
62
43
47
63
56
39
49
Figure 2:
Trigger Plate Parts Assembly
45
55
60
46
40
10
37
50
12 Gauge • 20 Gauge
Youth • Slug • 3" Chamber
Pardner® Pump
Shotgun
44
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising