INSTALLATION LOCATION & REMOVAL
INSTALLATION
LOCATION & REMOVAL
Important note;
Power and CAN connections
Switch off car and remove key, wait 10 minutes before removing any factory connectors.
Power and CAN connections are made at the BLACK plug from
the screen master unit.
INSTALLATION
Next connect the shorter of the supplied grey cables to
the black socket marked INPUT TO HARNESS on the
interface (see below)
Next plug in the longer of the supplied grey cables to
the metal screen socket,
Installation is made at the front, below the monitor on
all models, you will need to remove all the trims
shown to access the screen master unit.
You will need to connect the supplied 10 way WHITE plug loom
shown below, on to;
CAR
connect to NAV-INBMW3
(GREEN) can-low
to PIN 10 (GREEN)
(ORANGE/GREEN) can-high
to PIN 5 (ORANGE)
(RED 12v+ perm)
to PIN 1 (RED)
(BROWN12v– GROUND)
to PIN 2 (BROWN)
See “Operating Instructions” for;
and to the black socket marked OUTPUT TO SCREEN
on the interface (see below)
INPUT
OUTPUT
SUPPLY
PIN 3 12v– out (WHITE)
Next unplug the silver 10 way plug and black 12 way
plug from the monitor and remove from the car.
You may choose to mount the interface behind the
glove box area, which is easily removed with screws
at the front and underside of the glove box itself.
Plug the WHITE plug in to the socket in the interface marked
SUPPLY, FINALLY AFTER ALL OTHER CONNECTIONS.
AND REMOVE POWER FIRST BEFORE REMOVING ANY
OTHER CONNECTIONS. FAILURE CAN CAUSE FAULTS
Video connections
Connect the shorter of the supplied GREY cables to the silver
male 10 way plug of the car harness (removed from the
screen)
Connect your added video sources / camera to the
composite or RGB inputs shown below
OPERATING INSTRUCTIONS
The interface allows both composite video signals and RGB
signals to be displayed onto the existing OEM factory screen.
Installation Profiles
Before installation the following points must be considered:
How many inputs will be utilised (Aux 1 / 2 / reverse or RGB)?
If only one input will be used then switches 7 & 8 should be in the
up (OFF) position.
Will there be a reverse camera?
If there is, switch 3 will need to be down (ON) enabling Reverse control via
CAN detection, also switch ( should be down (ON) to enable optional full
screen camera picture by pressing the MENU button.
The source signals (composite video 1/2/reverse and RGB ) are
multi format supported; currently PAL and NTSC.
OPERATING INSTRUCTIONS
DIP Switch control options
Switch down is ON
Switch UP is off
12345678910-
OFF
OFF
Reverse camera input
OFF Auto video sense / ON Manual video select
OFF
OFF 12v- OUT follows picture overlay / ON 12v- OUT ACC
Enable Aux 2
Enable RGB
OFF
ON
To switch to aux inputs and also to switch back to factory system
press and hold the iDrive controller for 3 seconds.
To toggle through the aux inputs (if aux 2, RGB or Reverse camera
is active) press down the iDrive controller.
To stretch picture to full screen on any aux in press MENU
Interface Features
12V– is Ground only, used to power a relay to convert to 12V+
NAV-INROL
VIDEO INPUT
ROLLS ROYCE
DROP HEAD / COUPE
The interface has various features which can be selected/customised (via DIP
switches) to suit the installers/end users requirements.
With / Without TV Tuner
The available features are as follows:
CAN input (option to control inputs via iDrive)
NAV TV (Europe) LTD
V-HUB activation (option to control inputs via the iDrive controller)
Reverse Input (option to have reverse camera input and switched via CAN )
12V- Output (option to have 12v- output to follow picture Overlay or ACC)
NAV TV (Europe) LTD
Auxiliary 1 / 2 (option to control inputs via iDrive or V-HUB
RGB control (option to control inputs via iDrive or V-HUB
Super wide/Wide (option to see the selected input on the full screen)
Auto Video Sense / Manual video select with iDrive controller
Distribution Centre
Unit 21B Vale Business Park
Llandow, Vale of Glamorgan
CF71 7PF
Telephone:
+ 44 (0)8445 783 783
Fax:
+ 44 (0)1446 77 22 47
technical@nav.tv
Disclaimer
NAV TV (Europe) Ltd is not liable for any incidental, consequential or indirect damages. In case of erratic behavior of the vehicle’s
electrical system please disconnect the NAV TV product and contact our technical support Team. NAV TV (Europe) Ltd does not assume
liability for any diagnostic fees.
e11*72/245*95/54*3583*00
RoHS 2002/95/EC—2002/96/EC
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising