8203-33

8203-33
AMERICAN SPECIALTIES, INC.
441 Saw Mill River Road, Yonkers, NY 10701
(914) 476.9000 • (914) 476.0688
www.americanspecialties.com
MODEL №: 8203-33
ISSUED:
07/2014
REVISED:
7 July 2014
RECTANGULAR PHENOLIC FOLD-UP SHOWER SEAT (pg 1 of 2)
SPECIFICATION
Phenolic Fold –Up Shower Seat shall have all metal parts fabricated from alloy 18-8 stainless steel, type 304; seat
frame and support legs shall be 1" diameter (Ø25) and 1-1/4" (32) square x 18 gauge (1.2) with 3/16" (4.8) mounting
flanges and 16 gauge (1.5) guide bracket/arm support. All exposed surfaces shall have satin finish. Seat shall be
5/16" (8) thick phenolic with white color top and bottom surfaces and shall have black edges. Structural assembly shall
be of welded construction and all exposed edges and corners shall be radiused and/or deburred. Support arm shall fold
up when in retracted position to provide low profile against wall. No extra fittings shall be required to retain seat in
storage position. Guide bracket shall control seat lowering into operating position. Unit shall satisfy 2010 Accessibility
Standards when mounted properly.
Phenolic Fold-up Shower Seat shall be Model No 8203-33 as manufactured by American Specialties, Inc., 441
Saw Mill River Road, Yonkers, NY 10701-4913
INSTALLATION
This unit is surface mounted. Installer/construction contractor must provide concealed anchor plate or blocking as
specified in construction documents or as required by local building codes prior to wall finishing. Fasten unit flanges
and guide bracket to concealed anchor or blocking plate with appropriate hardware. See "STRENGTH" section below.
Note that concealed mounting plates or anchors and hardware are not supplied with this product and must be specified
separately. Ensure that mounting configuration complies with local building codes.
THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE
AMERICAN SPECIALTIES, INC.
441 Saw Mill River Road, Yonkers, NY 10701
(914) 476.9000 • (914) 476.0688
www.americanspecialties.com
MODEL №: 8203-33
ISSUED:
07/2014
REVISED:
7 July 2014
RECTANGULAR PHENOLIC FOLD-UP SHOWER SEAT (pg 2 of 2)
STRENGTH
ASI Shower Seats are designed to meet and exceed 2010 ADA Accessibility Standards and ANSI A117.1 that
fabricated product shall be of adequate strength to support a load of 250 pounds (113.4 kg) and unit shall conform to
size and edge clearances as diagrammed. Mounting to the wall is a critical part of the system to meet this requirement.
To withstand the shear, tension or pullout, and torsion loads generated by the maximum loading, the fastener system
must be adequately sized. Unit will carry a load of 500 lbs if properly installed. The supporting wall must be adequately reinforced to carry the rated load for the products lifetime.
MATERIALS
Tube:
18 gauge (.048" <1.22> thick) type 304 stainless steel, 1" (Ø25) dia. and 1-1/4" (32) square. Unitized all
welded construction. Exposed surfaces are satin finish. Edges and corners are radiused and burr free.
Flange:
3/16" (4.8) type 304 stainless steel. Exposed surfaces have satin finish. Edges and corners are radiused
and burr free.
Bracket: 16 gauge (.06" <1.52> thick) type 304 stainless steel. Exposed surfaces are satin finish. Edges and corners
are radiused and burr free.
Seat:
Solid Phenolic 5/16" x 33" x 14-1/2" (8 x 838 x 368). Exposed surfaces have semi-gloss laminate white
colored top and bottom surfaces and shall have black edges. Corners are radiused and burr free. Seat top
shall have seven (7) total slots 1/4" (6) wide with three (3) slots 11-3/4" (30) long and four (4) slots 43/4" (121) long for water drainage and user slip resistance. Mounting hardware is stainless steel dome head
carriage bolts with acorn nuts on bottom.
Spring: Stainless steel wire type 304 OD 27/32" (Ø21,6) coils x 2-1/4" body length (57,2) x .085" (Ø2,2) wire diameter.
OPERATION
Fold-up Shower Seat requires only one hand operation to manually lower to horizontal position for use or raise for
departure and arrival. Guide bracket with spring detent prevents seat from dropping and provides positive support
in usage position as well as spring locked storage position.
THIS MANUFACTURER RESERVES THE RIGHT TO MAKE CHANGES IN DESIGN OR DIMENSIONS WITHOUT FORMAL NOTICE
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising