390 HP-Agilent 6063B 01

390 HP-Agilent 6063B 01
Agilent 6060B and 6063B Single-Input
250 to 300 W Electronic Loads, GPIB
Data Sheet
Maximize throughput with real-life loading conditions
• Cost-effective for single input applications
• Convenient optional front panel input connection
The 6060B and 6063B each provides
one load input. This is more convenient
for single input applications than a
mainframe product.
These electronic loads are particularly
suited for the lab bench. Entering
commands manually using the front
panel keypad is simpler because the
channel does not need to be specified,
as in a mainframe configuration. The
keypad entry is further simplified
because these products do not have
the downloadable LIST feature of the
N3300A Series, which helps to
maximize production throughput.
Extensive protection is included to
help protect your valuable prototypes
under test. This includes overvoltage,
overcurrent, overtemperature, overpower, and reverse polarity.
These loads are suitable for manufacturing test systems where maximizing
speed is not critical. They use industry
standard SCPI instructions, and also
have VXIplug&play drivers to simplify
system design. For the greatest speed
and accuracy in programming and
measurement, see the N3300A series
of DC electronic loads.
Specifications
Specifications
(at 25 °C ± 5 °C unless otherwise specified)
6060B
6063B
DC Input ratings
Current
0 to 60 A
0 to 10 A
Voltage
3 to 60 V
3 to 240 V
Maximum power (at 40° C)
300 W
250 W
Ranges
0 to 6 A, 0 to 60 A
0 to 1 A, 0 to 10 A
Accuracy
0.1% ± 75 mA
0.15% ± 10 mA
Regulation
10 mA
8 mA
Accuracy
0.1% ± 50 mV
0.12% ± 120 mV
Regulation (w/remote sense)
10 mV
10 mV
Constant current mode
Constant voltage mode
Constant resistance mode
Ranges
Accuracy
0.033 to 1.0 Ω
0.20 to 24.0 Ω
1 to 1,000 Ω
24 to 10,000 Ω
10 to 10,000 Ω
240 to 50,000 Ω
1 Ω: 0.8% ± 8 mΩ (with ≥ 6 A at input)
24 Ω: 0.8% ± 200 mΩ (with ≥ 1 A at input)
1 KΩ: 0.3% ± 8 mΩ (with ≥ 6 V at input)
10 KΩ: 0.3% ± 0.3 mΩ (with ≥ 24 V at input)
10 KΩ: 0.3% ± 8 mΩ (with ≥ 6 V at input) 50 KΩ: 0.3% ± 0.3 mΩ (with ≥ 24 V at input)
Transient generator
Frequency range
0.25 Hz to 10 kHz
0.25 Hz to 10 kHz
Accuracy
3%
3%
Duty cycle range
3 to 97% (0.25 Hz to 1 kHz)
3 to 97% (0.25 Hz to 1 kHz)
6 to 94% (1 to 10 kHz)
6 to 94% (1 to 10 kHz)
Accuracy
6% of setting ± 2%
6% of setting ± 2%
Current level high range
0 to 60 A
0 to 10 A
Accuracy
0.1% ± 350 mA
0.18% ± 50 mA
Current level low range
0 to 6 A
0 to 1 A
Accuracy
0.1% ± 80 mA
0.18% ± 13 mA
Voltage level
0 to 60 V
0 to 240 V
Voltage level accuracy
0.1% ± 300 mV
0.15% ± 1.1 V
Current
0.05% ± 65 mA
0.12% ±10 mA
Voltage
± (0.05% + 45 mV)
± (0.1% + 150 mV)
Readback accuracy
Ripple and noise (20 Hz to 10 MHz noise)
Current
Voltage
2
4 mA rms
1 mA rms
40 mA peak-to-peak
10 mA peak-to-peak
6 mV rms
6 mV rms
Specifications, continued
Supplemental characteristics
(Non-warranted characteristics determined
by design and useful in applying the product)
Constant current mode
Resolution
Temperature coefficient
Constant voltage mode
Resolution
Temperature coefficient
Constant resistance mode
Resolution
Temperature coefficient
Transient generator
Frequency range
Resolution
Duty cycle range
Resolution
Current level high range
Resolution
Current level low range
Resolution
Current temperature coefficient
Voltage level resolution
Voltage temperature coefficient
Programmable slew rate
Rise/fall time
Analog programming bandwidth
Analog programming accuracy
Current (low range)
Current (high range)
Temperature coefficient
Voltage
Temperature coefficient
Analog programming voltage
Readback specifications
Current readback resolution
Temperature coefficient
Voltage readback resolution
Temperature coefficient
6060B
6063B
60 A range: 16 mA
6 A range: 1.6 mA
100 ppm/°C ± 5 mA/°C
10 A range: 2.6 mA
1 A range: 0.26 mA
150 ppm/°C ± 1 mA/°C
16 mV
100 ppm/°C ± 5 mV/°C
64 mV
120 ppm/°C ± 10 mV/°C
1 Ω : 0.27 mΩ
1 KΩ: 0.27 ms
10 KΩ: 0.027 ms
1 Ω: 800 ppm/°C ± 0.4 mΩ/°C
1 KΩ: 300 ppm/°C ± 0.6 ms/°C
10 KΩ: 300 ppm/°C ± 0.6 ms/°C
24 Ω: 6 mΩ
10 KΩ: 0.011 ms
50 KΩ: 0.001 ms
24 Ω: 800 ppm/°C ± 10 mΩ/°C
10 KΩ: 300 ppm/°C ± 0.03 ms/°C
50 KΩ: 300 ppm/°C ± 0.03 ms/°C
0.25 Hz to 10 kHz
4% or less
3 to 97% (0.25 Hz to 1 kHz)
6 to 94% (1 to 10 kHz)
4%
60 A range:
260 mA
6 A range:
26 mA
100 ppm/°C ± 7 mA/°C
260 mV
150 ppm/°C ± 5 mV/°C
60 A range: 1 A/ms to 5 A/μs
6 A range: 0.1 A/ms to 0.5 A/μs
12 μs to 8 ms
10 kHz (–3 dB frequency)
0.25 Hz to 10 kHz
4% or less
3 to 97% (0.25 Hz to 1 kHz)
6 to 94% (1 to 10 kHz)
4%
10 A range:
43 mA
1 A range:
4 mA
180 ppm/°C ± 1.2 mA/°C
1V
120 ppm/°C ± 10 mV/°C
10 A range: 0.17 A/ms to 0.83 A/μs
1 A range: 17 A/ms to 83 A/ms
16 μs to 8 ms
10 kHz (–3 dB frequency)
4.5% ± 75 mA
4.5% ± 250 mA
100 ppm/°C ±6 mA/°C
0.8% ± 200 mV
100 ppm/°C ± 1 mV/°C
0 to 10 V
3% ± 8 mA
3% ± 20 mA
150 ppm/°C ± 1 mA/°C
0.5% ± 150 mV
120 ppm/°C ± 10 mV/°C
0 to 10 V
17 mA (via GPIB)
20 mA (front panel)
50 ppm/°C ± 5 mA/°C
17 mV (via GPIB)
20 mV (front panel)
50 ppm/°C ± 1.2 mV/°C
2.7 mA (via GPIB)
10 mA (front panel)
100 ppm/°C ± 1 mA/°C
67 mV (via GPIB)
100 mV (front panel)
100 ppm/°C ± 8 mV/°C
Notes:
1. Operating temperature range is 0° to 55 °C. All specifications apply for 25 °C ± 5 °C, except as noted.
2. Maximum continuous power available is derated linearly from 40 °C to 75% of maximum at 55 °C.
3. DC current accuracy specifications apply 30 seconds after input is applied.
3
Specifications, continued
Supplemental characteristics
(Non-warranted characteristics determined
by design and useful in applying the product)
6060B
6063B
Analog monitor accuracy
Current monitor (0 to 10 Vout)
4% ± 85 mA
3% ± 10 mA
Temperature coefficient
50 ppm/°C ± 6 mA/°C
100 ppm/°C ± 1 mA/°C
Voltage monitor (0 to 10 Vout)
0.25% ± 40 mV
0.4% ± 240 mV
Temperature coefficient
50 ppm/°C ± 0.2 mV/°C
70 ppm/°C ± 1.2 mV/°C
Remote sensing
5-VDC maximum between sense and
load input
5-VDC maximum between sense and
load input
Minimum operating voltage
(at full rated current)
2 V (1.2 V typical)
2 V (1.2 V typical)
Programmable short
0.033 Ω (0.020 Ω typical)
0.20 Ω (0.10 Ω typical)
Programmable open (typical)
20 kΩ
80 kΩ
Current
0.03% ± 10 mA
0.03% ± 15 mA
Voltage
0.01% ± 10 mV
0.01% ± 20 mV
DC isolation voltage
± 240 VDC, between any input and
chassis ground
± 240 VDC, between any input and
chassis ground
Digital inputs
VIL = 0.9 Vmax at IIL =
–1 mA / VIH = 3.15 Vmin
(pull-up resistor on input)
VIL = 0.9 Vmax at IIL =
–1 mA / VIH = 3.15 Vmin
(pull-up resistor on input)
Digital outputs
VOL = 0.72 Vmax at IOL =
1 mA / VOH = 4.4 Vmin
at IOH = –20 μA
VOL = 0.72 Vmax at IOL =
1 mA / VOH = 4.4 Vmin
at IOH = –20 μA
Drift (over 8-hour interval)
Notes:
1. Operating temperature range is 0° to 55 °C. All specifications apply for 25 °C ± 5 °C, except as noted.
2. Maximum continuous power available is derated linearly from 40 °C to 75% of maximum at 55 °C.
3. DC current accuracy specifications apply 30 seconds after input is applied.
4
Supplemental characteristics
for all model numbers
Software driver: VXIplug&play
Size:
425.5 mm W x 88.1 mm H x 396 mm D
(16.75 in x 3.5 in x 13.7 in )
Weight: 6.12 kg (13.5 lb) net; 8.16 kg
(18 lb) shipping
Warranty: One year
Agilent models: 6060B, 6063B
28.6 mm
1.1"
Top
396 mm
13.7"
34.9 mm
1.4"
425.5 mm
16.75"
41.3 mm
1.7"
88.1 mm
3.5"
101.6 mm
16.75"
Side
Rear
12.7 mm
0.5"
50.8 mm
2.0"
5
www.agilent.com
www.agilent.com/find/6060
Ordering information
The 6060B and 6063B come with
full documentation on CD-ROM. The
CD-ROM includes operating manual,
programming guide, service manual,
and application notes.
Opt 020 Front panel DC input
connectors
Opt 100 87 to 106 VAC, 47 to 66 Hz
input (for Japan only)
Opt 120 104-127 VAC, 47 to 66 Hz
Opt 220 191 to 233 VAC, 47 to 66 Hz
input
Opt 240 209 to 250 VAC, 47 to 66 Hz
input
For more information on Agilent
Technologies’ products, applications or
services, please contact your local Agilent
office. The complete list is available at:
www.agilent.com/find/contactus
Agilent Advantage Services is committed
to your success throughout your equipment’s lifetime. To keep you competitive,
we continually invest in tools and
processes that speed up calibration and
repair and reduce your cost of ownership.
You can also use Infoline Web Services
to manage equipment and services more
effectively. By sharing our measurement
and service expertise, we help you create
the products that change our world.
www.agilent.com/find/advantageservices
Opt 0L1 Printed operating manual
and programming guide
Opt 0B3 Printed service manual
Agilent Electronic Measurement Group
DEKRA Certified
ISO 9001:2008
Quality Management Sys
System
Accessories
1CM002A* Rack mount flange kit
88.1 mm H (2U) – two flange brackets;
1.75 Inch hole spacing
1CP001A* Rack mount flange and
handle kit 88.1 mm H (2U) – two
brackets and front handles
E3663AC Support rails for Agilent
rack cabinets
www.agilent.com/quality
Agilent Email Updates
www.agilent.com/find/emailupdates
Get the latest information on the
products and applications you select.
Agilent Channel Partners
Application notes
Agilent AN 372-1 Power Supply
Testing, 5952-4190
Agilent AN 372-2 Battery Testing,
5952-4191
www.agilent.com/find/channelpartners
Get the best of both worlds: Agilent’s
measurement expertise and product
breadth, combined with channel
partner convenience.
Americas
Canada
Brazil
Mexico
United States
(877) 894 4414
(11) 4197 3600
01800 5064 800
(800) 829 4444
Asia Pacific
Australia
China
Hong Kong
India
Japan
Korea
Malaysia
Singapore
Taiwan
Other AP Countries
1 800 629 485
800 810 0189
800 938 693
1 800 112 929
0120 (421) 345
080 769 0800
1 800 888 848
1 800 375 8100
0800 047 866
(65) 375 8100
Europe & Middle East
Belgium
32 (0) 2 404 93 40
Denmark
45 45 80 12 15
Finland
358 (0) 10 855 2100
France
0825 010 700*
*0.125 €/minute
Germany
Ireland
Israel
Italy
Netherlands
Spain
Sweden
United Kingdom
49 (0) 7031 464 6333
1890 924 204
972-3-9288-504/544
39 02 92 60 8484
31 (0) 20 547 2111
34 (91) 631 3300
0200-88 22 55
44 (0) 118 927 6201
For other unlisted countries:
www.agilent.com/find/contactus
Revised: January 6, 2012
Pulsed Characterization of Power
Semiconductors Using Electronic
Loads (AN 1246) 5091-7636E
Product specifications and descriptions
in this document subject to change
without notice.
* Support rails required
© Agilent Technologies, Inc. 2012
Published in USA, March 23, 2012
5990-9308EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising