OPERATOR AND PARTS MANUAL Fertilizer Applicator Model 1860 and 2460

OPERATOR AND PARTS MANUAL Fertilizer Applicator Model 1860 and 2460
OPERATOR AND PARTS MANUAL
Fertilizer Applicator
Model 1860 and 2460
092013
6990633 (1-13)
88665046
Printed in U.S.A.
© Bobcat Company 2013
062013 | Rev 1 | 88664296
Table of Contents - 1860 and 2460 Fertilizer Applicator
TABLE OF CONTENTS
Manufacturer’s Statement: For technical reasons, Buhler Industries Inc. reserves the right to modify machinery design
and specifications provided herein without any preliminary notice. Information provided herein is of descriptive nature.
Performance quality may depend on soil fertility, applied agricultural techniques, weather conditions and other factors.
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
PARTS IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
ALPHABETICAL INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
1
Table of Contents - 1860 and 2460 Fertilizer Applicator
2
Warranty Registration - 1860 and 2460 Fertilizer Applicator
WARRANTY REGISTRATION FORM
This form must be filled out by the dealer and signed by both the dealer and the customer at the time of delivery.
Customer Name:
Dealer Name:
Customer Address:
Dealer Address:
City:
Prov / State:
City:
Prov / State:
Postal / Zip Code:
Phone:
Postal / Zip Code:
Phone:
Fertilizer Applicator Model:
Serial Number:
Delivery Date:
I have thoroughly instructed the buyer on the above described equipment which review included the Operator and Parts
Manual content, equipment care, adjustments, safe operation and applicable warranty policy.
Dealer Inspection Report
Safety
Toolbar Moves Up / Down Freely
All Lights And Reflectors Installed
Inner And Outer Wings Fold / Extend Freely
All Lights And Reflectors Cleaned And Working
Wheel Bolts Are Tight
Safety Chain On Hitch
Monitors Function Correctly
All Decals Installed
Hydraulic & Application Hoses And Fittings Tight
Guards And Shields Installed And Secure
All Fasteners Are Tight
Review Operating And Safety Instructions
Lubricate Machine
Check For Hydraulic Leaks
Check Tire Pressure
Date:
Dealer Rep. Signature:
The above equipment and Operator And Parts Manual have been received by me and I have been thoroughly
instructed as to care, adjustments, safe operation and applicable warranty policy.
Date:
Customer / Owner’s Signature:
Remove this Warranty Registration Form from the Operator And Parts Manual. Make two copies of the form. Send
original Warranty Registration Form to Farm King. Give one copy to the customer and the dealer will keep one copy.
3
Warranty Registration - 1860 and 2460 Fertilizer Applicator
4
Introduction - 1860 and 2460 Fertilizer Applicator
INTRODUCTION
This Operator’s and Parts Manual was written to give the owner / operator instructions on the safe operation, maintenance
and part identification of the Farm King equipment. READ AND UNDERSTAND THIS OPERATOR’S AND PARTS
MANUAL BEFORE OPERATING YOUR FARM KING EQUIPMENT. If you have any questions, see your Farm King
dealer. This manual may illustrate options and accessories not installed on your Farm King equipment.
OWNER’S INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Serial Number Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Manual Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
EQUIPMENT IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Component Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5
Introduction - 1860 and 2460 Fertilizer Applicator
6
Introduction - 1860 and 2460 Fertilizer Applicator
OWNER’S INFORMATION
Serial Number Location
Thank you for your decision to purchase a Farm King
1860 / 2460 Fertilizer Applicator. To ensure maximum
performance of your equipment, it is mandatory that you
thoroughly study the Operator and Parts Manual and
follow the recommendations. Proper operation and
maintenance are essential to maximize equipment life
and prevent personal injury.
Please enter the model and serial number in the space
provided for easy reference.
Figure 1
1
Operate and maintain this equipment in a safe manner
and in accordance with all applicable local, state, and
federal codes, regulations and / or laws. Follow all onproduct labeling and instructions.
Make sure that all personnel have read this Operator and
Parts Manual and thoroughly understand safe and
correct operating, installation and maintenance
procedures.
Farm King is continually working to improve its products.
Farm King reserves the right to make any improvements
or changes as deemed practical and possible without
incurring any responsibility or obligation to make any
changes or additions to equipment sold previously.
Although great care has been taken to ensure the
accuracy of this publication, Farm King, makes no
warranty or guarantee of any kind, written or expressed,
implied or otherwise with regard to the information
contained within this manual. Farm King assumes no
responsibility for any errors that may appear in this
manual and shall not be liable under any circumstances
for incidental, consequential or punitive damages in
connection with, or arising from the use of this manual.
Keep this manual available for frequent reference. All new
operators or owners must review the manual before using
the equipment and annually thereafter. Contact your
Farm King Dealer if you need assistance, information, or
additional copies of the manual. Visit our website at
www.farm-king.com for a complete list of dealers in
your area.
B-0123
Model Number:
Serial Number:
The serial number plate (Item 1) [Figure 1] is located on
the front right lower hitch frame, across from the jack.
Always use your serial number when requesting
information or when ordering parts.
Manual Storage
Figure 2
1
The directions left, right, front and rear, as mentioned
throughout this manual, are as viewed from the rear of
the equipment.
B-0124
The operator and parts manual and other documents can
be stored in the canister (Item 1) [Figure 2] located
behind the hitch on the front of the fertilizer applicator.
7
Introduction - 1860 and 2460 Fertilizer Applicator
EQUIPMENT IDENTIFICATION
Component Location
TOOLBAR
FLOW
MONITOR
FRONT
SIGHT
GAUGE
SPRAY
TANK
FLOW
MONITOR
HITCH / SAFETY CHAIN
LIGHT BAR
FLOW
MONITOR
INNER WING
WING LOAD VALVE
GAUGE
WHEEL
OUTER WING
COULTER
B-0125
8
Introduction - 1860 and 2460 Fertilizer Applicator
Component Location
AMBER LIGHT
REAR
SIGHT
GAUGE
TANK VENT
RED LIGHT
FRESH WATER
TANK
RED LIGHT
AMBER LIGHT
SPRAY PUMP
FILL VALVE
B-0189
9
Introduction - 1860 and 2460 Fertilizer Applicator
10
Safety - 1860 and 2460 Fertilizer Applicator
SAFETY
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Safe Operation Is The Operator’s Responsibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Safe Operation Needs A Qualified Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Use Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Transport Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Safety Rules For Power Take-Off (PTO) Driven Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Machine Requirements And Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
FIRE PREVENTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Hydraulic System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Spark Arrester Exhaust System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Welding And Grinding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Fire Extinguishers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Rules For Safe Use Of Chemicals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SAFETY SIGNS (DECALS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
EQUIPMENT DECALS AND SIGNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SAFETY SIGN-OFF FORM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
11
Safety - 1860 and 2460 Fertilizer Applicator
12
Safety - 1860 and 2460 Fertilizer Applicator
SAFETY INSTRUCTIONS
Safe Operation Needs A Qualified Operator
Safe Operation Is The Operator’s Responsibility
Safety Alert Symbol
This symbol with a warning statement means:
“Warning, be alert! Your safety is involved!”
Carefully read the message that follows.
Operators must have instructions before operating
the machine. Untrained operators can cause injury
or death.
For an operator to be qualified, he or she must not use
drugs or alcohol which impair alertness or coordination
while working. An operator who is taking prescription
drugs must get medical advice to determine if he or she
can safely operate a machine and the equipment.
The signal word CAUTION on the machine and in the
manuals indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against
unsafe practices.
A Qualified Operator Must Do The Following:
Understand
Regulations
the
Written
Instructions,
Rules
and
•
The written instructions from Farm King include the
Warranty Registration, Dealer Inspection Report,
Operator’s and Parts Manual and machine signs
(decals).
•
Check the rules and regulations at your location. The
rules may include an employer’s work safety
requirements. Regulations may apply to local driving
requirements or use of a Slow Moving Vehicle (SMV)
emblem. Regulations may identify a hazard such as a
utility line.
The signal word DANGER on the machine and in the
manuals indicates a hazardous situation which, if
not avoided, will result in death or serious injury.
Have Training with Actual Operation
The signal word WARNING on the machine and in
the manuals indicates a potentially hazardous
situation which, if not avoided, could result in death
or serious injury.
•
Operator training must consist of a demonstration and
verbal instruction. This training is given by the
machine owner prior to operation.
•
The new operator must start in an area without
bystanders and use all the controls until he or she can
operate the machine safely under all conditions of the
work area. Always fasten seat belt before operating.
Know the Work Conditions
•
Clear working area of all bystanders, especially small
children and all obstacles that might be hooked or
snagged, causing injury or damage.
•
Know the location of any overhead or underground
power lines. Call local utilities and have all
underground power lines marked prior to operation.
•
Wear tight fitting clothing. Always wear safety glasses
when doing maintenance or service.
This notice identifies procedures which must be
followed to avoid damage to the machine.
13
Safety - 1860 and 2460 Fertilizer Applicator
Use Safety Rules
•
Read and follow instructions in this manual and the
tractor’s Operators Manual before operating.
•
Read Chemical manufacturers Warnings, Instructions
and Procedures before starting and follow them
exactly.
•
Under no circumstances should young children be
allowed to work with this equipment.
•
This equipment is dangerous to children and persons
unfamiliar with its operation.
•
If the elderly are assisting with work, their physical
limitations
need
to
be
recognized
and
accommodated.
•
Check for overhead and / or underground lines before
operating equipment (if applicable).
•
In addition to the design and configuration of
equipment, hazard control and accident prevention
are dependent upon the awareness, concern,
prudence and proper training of personnel involved in
the operation, transport, maintenance and storage of
equipment.
•
Check that the equipment is securely fastened to the
tractor / towing vehicle.
•
Make sure all the machine controls are in the
NEUTRAL position before starting the machine.
•
Operate the equipment only from the operator’s
position.
•
Operate the equipment according to the Operator’s
and Parts Manual.
•
When learning to operate the equipment, do it at a
slow rate in an area clear of bystanders, especially
small children.
•
DO NOT permit personnel to be in the work area
when operating the equipment.
14
•
The equipment must be used ONLY on approved
tractors / transport vehicles.
•
DO NOT modify the equipment in any way.
Unauthorized modification may impair the function
and / or safety and could affect the life of the
equipment.
•
Stop tractor engine, place all controls in neutral, set
park brake, remove ignition key and wait for all
moving parts to stop before servicing, adjusting,
repairing, unplugging or filling.
•
DO NOT make any adjustments or repairs on the
equipment while the machine is running.
•
Keep shields and guards in place. Replace if
damaged.
•
Keep hands, feet, hair and clothing away from all
moving parts.
Safety - 1860 and 2460 Fertilizer Applicator
Transport Safety
•
Do not exceed 20 mph (32 kph). Reduce speed on
rough roads and surfaces.
•
Comply with state and local laws governing highway
safety and movement of machinery on public roads.
•
The use of flashing amber lights is acceptable in most
localities. However, some localities prohibit their use.
Local laws should be checked for all highway lighting
and marking requirements.
Safety Rules For Power Take-Off (PTO) Driven
Equipment
•
Keep PTO shields and all guards in place. Replace
damaged or missing shields and guards before
operating.
•
Follow warnings and instructions on machine signs
(decals). Replace damaged or missing decals.
•
Do not wear loose or bulky clothing around the PTO
or other moving parts.
•
Do not transport with fluid in the tank.
•
Keep bystanders away from PTO driven equipment,
and never allow children near machines.
•
Close lock valves in wing extend hydraulic circuits
before transporting.
•
Read and understand the manuals for the PTO driven
equipment and be aware of safe operating
procedures and hazards that may not be readily
apparent.
•
Always walk around equipment to avoid coming near
a turning PTO driveline. Stepping over, leaning
across or crawling under a turning PTO driveling can
cause entanglement.
•
Position the machine and equipment hitch correctly to
prevent driveline stress and separation.
•
Use caution when turning. Turning too sharp can
cause driveline damage.
•
Use caution when raising PTO driven attachment.
Excessive driveline angle can cause driveline
damage. Use stops if needed.
•
Always install transport locks, pins or brackets before
transporting.
•
Always yield to oncoming traffic in all situations and
move to the side of the road so any following traffic
may pass.
•
Always enter curves or drive up or down hills at a low
speed and at a gradual steering angle.
•
Never allow riders on either tractor or equipment.
•
Keep tractor / towing vehicle in a lower gear at all
times when traveling down steep grades.
•
Maintain proper brake settings at all times (if
equipped).
15
Safety - 1860 and 2460 Fertilizer Applicator
Machine Requirements And Capabilities
FIRE PREVENTION
•
Fasten seat belt securely. If equipped with a foldable
Roll-Over Protective Structure (ROPS), only fasten
seat belt when ROPS is up and locked. DO NOT wear
seat belt if ROPS is down.
•
Machine’s three-point hitch must be equipped with
sway bars or chains.
Maintenance
•
Stop the machine and engage the parking brake.
Install blocks in front of and behind the rear tires of the
machine. Install blocks underneath and support the
equipment securely before working under raised
equipment.
The machine and some equipment have components
that are at high temperatures under normal operating
conditions. The primary source of high temperatures is
the engine and exhaust system. The electrical system, if
damaged or incorrectly maintained, can be a source of
arcs or sparks.
•
Keep bystanders clear of moving parts and the work
area. Keep children away.
•
Use increased caution on slopes and near banks and
ditches to prevent overturn.
•
Make certain that the Slow Moving Vehicle (SMV)
emblem is installed so that it is visible and legible.
When transporting the equipment, use the flashing
warning lights (if equipped) and follow all local
regulations.
•
Operate this equipment with a machine equipped with
an approved Roll-Over Protective Structure (ROPS).
Always wear seat belt when the ROPS is up. Serious
injury or death could result from falling off the
machine.
Flammable debris (leaves, straw, etc.) must be removed
regularly. If flammable debris is allowed to accumulate, it
can cause a fire hazard. Clean often to avoid this
accumulation. Flammable debris in the engine
compartment is a potential fire hazard.
The operator’s area, engine compartment and engine
cooling system must be inspected every day and cleaned
if necessary to prevent fire hazards and overheating.
All fuels, most lubricants and some coolant mixtures are
flammable. Flammable fluids that are leaking or spilled
onto hot surfaces or onto electrical components can
cause a fire.
Operation
•
Before leaving the operator’s position:
The Farm King machine must be in good operating
condition before use.
1.
2.
3.
4.
5.
Always park on a flat level surface.
Place all controls in neutral.
Engage the parking brake.
Stop engine.
Wait for all moving parts to stop.
Check all of the items listed on the service schedule
under the 8 hour column. (See “SERVICE SCHEDULE”
on page 60.)
•
Carry passengers only in designated seating areas.
Never allow riders on the machine or equipment.
Falling off can result in serious injury or death.
•
Start the equipment only when properly seated in the
operator’s seat. Starting a machine in gear can result
in serious injury or death.
•
Operate the machine and equipment from the
operator's position only.
•
16
The parking brake must be engaged before leaving
the operator’s seat. Rollaway can occur because the
transmission may not prevent machine movement.
Do not use the machine where exhaust, arcs, sparks or
hot components can contact flammable material,
explosive dust or gases.
Starting
Do not use ether or starting fluids on any engine that has
glow plugs. These starting aids can cause explosion and
injure you or bystanders.
Use the procedure in the tractor’s operator’s manual for
connecting the battery and for jump starting.
Safety - 1860 and 2460 Fertilizer Applicator
Electrical
Welding And Grinding
Always clean the machine and equipment, disconnect
the battery, and disconnect the wiring from the machine
controls before welding. Cover rubber hoses, battery and
all other flammable parts. Keep a fire extinguisher near
the machine when welding.
Check all electrical wiring and connections for damage.
Keep the battery terminals clean and tight. Repair or
replace any damaged part or wires that are loose or
frayed.
Battery gas can explode and cause serious injury. Do not
jump start or charge a frozen or damaged battery. Keep
any open flames or sparks away from batteries. Do not
smoke in battery charging area.
Have good ventilation when grinding or welding painted
parts. Wear dust mask when grinding painted parts.
Toxic dust or gas can be produced.
Dust generated from repairing nonmetallic parts such as
hoods, fenders or covers can be flammable or explosive.
Repair such components in a well ventilated area away
from open flames or sparks.
Fire Extinguishers
Hydraulic System
Check hydraulic tubes, hoses and fittings for damage
and leakage. Never use open flame or bare skin to check
for leaks. Hydraulic tubes and hoses must be properly
routed and have adequate support and secure clamps.
Tighten or replace any parts that show leakage.
Always clean fluid spills. Do not use gasoline or diesel
fuel for cleaning parts. Use commercial nonflammable
solvents.
Fueling
Know where fire extinguishers and first aid kits are
located and how to use them. Inspect the fire
extinguisher and service the fire extinguisher regularly.
Obey the recommendations on the instructions plate.
Stop the engine and let it cool before adding fuel. No
smoking! Do not refuel a machine near open flames or
sparks. Fill the fuel tank outdoors.
Spark Arrester Exhaust System
The spark arrester exhaust system is designed to control
the emission of hot particles from the engine and exhaust
system, but the muffler and the exhaust gases are still
hot.
Check the spark arrester exhaust system regularly to
make sure it is maintained and working properly. Use the
procedure in the machine’s Operator’s Manual for
cleaning the spark arrester muffler (if equipped).
17
Safety - 1860 and 2460 Fertilizer Applicator
•
Do not spill chemicals on skin or clothing. If chemicals
are
spilled,
remove
contaminated
clothing
immediately and wash skin (and clothing) thoroughly
with soap and water. Wash hands and face with soap
and water and change clothing after spraying. Wash
clothing each day before reuse.
•
The spray tank and system should be emptied of
chemical mixture and flushed with clean water before
servicing the spray system or spray components.
Clean machine of all chemical residue before
servicing.
•
Keep all chemical lines, fittings and couplers tight and
free of leaks before starting and operating.
•
Do not allow chemical or solution to touch skin.
Some chemicals can be absorbed through the
skin.
Rinse the applicator off before leaving the fertilized
field. Never contaminate the farmyard or drainage
system with applicator rinse.
•
Wear rubber gloves and protective gear at all
times.
Avoid inhaling chemicals. When directed on the label,
wear protective clothing, face shield or goggles.
•
Never smoke while spraying or handling chemicals.
•
Cover food and water containers when spraying
around livestock or pet areas.
•
If symptoms of illness occurs during or shortly after
spraying, call a physician or go to a hospital
immediately.
•
Follow label directions and advise to keep residues on
edible portions of plants within the limits permitted by
law.
•
Keep chemicals out of the reach of children, pets and
unauthorized personnel. Store them outside of the
home, away from food and feed and lock them in a
secure area.
•
Keep bystanders away from spray drift.
•
Always store chemicals in original containers and
keep them tightly closed. Never keep them in
anything but the original container. Read labels for
hazards about chemical reaction with certain types of
metals.
•
Always dispose of empty containers according to
manufacturer’s directions.
Rules For Safe Use Of Chemicals
CHEMICAL HAZARD
To prevent serious injury or death:
WEAR PERSONAL PROTECTIVE EQUIPMENT
•
•
DON’T BREATH VAPOR
•
Avoid chemical splash and vapor. Keep others
away.
•
Do not breathe vapor.
•
Wear proper respirator when working with
chemicals.
•
Chemicals can be toxic.
DON’T INGEST CHEMICAL
•
If in eyes or mouth, read manufacturer’s
instructions and follow them exactly.
•
Seek immediate medical attention.
•
A poison control number is usually inside the
front cover of your telephone book.
•
Always read the label before using chemicals. Follow
instructions from chemical manufacturer on how to
select, use and handle each chemical. Note
protection information each time before opening the
container.
•
Verbal warnings must be given if written warnings
cannot be understood by workers.
18
Safety - 1860 and 2460 Fertilizer Applicator
SAFETY SIGNS (DECALS)
Follow the instructions on all the Signs (Decals) that are on the equipment. Replace any damaged signs (decals)
and be sure they are in the correct locations. Equipment signs are available from your Farm King equipment dealer.
Front Left Side Of Hitch
Rear Of Chassis Frame (Rear Of Machine)
3
2
5
2
1
3
4
1
4
B-0156
B-0147
1
2
p/n 88665017
p/n 88664875
3
4
2
1
p/n 88665016
3
p/n 88664875
4
p/n SX008553
p/n 88664935
5
p/n 88665018
p/n 88664936
p/n 88664962
19
Safety - 1860 and 2460 Fertilizer Applicator
Pivot Points On Wings (Front and Back)
1
B-0135
1
p/n 002439
20
Safety - 1860 and 2460 Fertilizer Applicator
EQUIPMENT DECALS AND SIGNS
NOTE: All safety related decals are shown in the
Safety Signs Section. (See “SAFETY SIGNS
(DECALS)” on page 19.)
Part Number 88665331
Part Number 88665330
Check and replace any worn, torn, hard to read or
missing decals on your equipment.
Part Number 88664871 (Left Side)
Part Number 88664872 (Right Side)
Part Number 88664873 (Left Side)
Part Number 88664874 (Right Side)
Part Number SX17 - 5910B (Amber)
Part Number SX17 - 5915B (Red)
Part Number SX17 - 5920B (Day Orange)
Part Number JD5403
21
Safety - 1860 and 2460 Fertilizer Applicator
SAFETY SIGN-OFF FORM
Instructions are necessary before operating or servicing equipment. Read and understand the
Operator’s and Parts Manual and safety signs (decals) on equipment. Follow warnings and
instructions in the manuals when making repairs, adjustments or servicing. Check for correct
function after adjustments, repairs or service. Untrained operators and failure to follow instructions
can cause injury or death.
Farm King follows the general Safety Standards specified by the American Society of Agricultural and Biological
Engineers (ASABE) and the Occupational Safety and Health Administration (OSHA). Anyone who will be operating and /
or maintaining the 1860 and 2460 fertilizer applicator must read and clearly understand ALL Safety, Operating and
Maintenance information presented in this manual.
Annually review this information before the season start-up and make these periodic reviews of SAFETY and
OPERATION a standard practice for all of your equipment. An untrained operator is unqualified to operate this machine.
The following sign-off sheet is provided for your record and to show that all personnel who will be working with the
equipment have read and understand the information in this Operator’s and Parts Manual and have been instructed in the
operation of the equipment.
SIGN-OFF SHEET
Date
22
Employee’s Signature
Employer’s Signature
Assembly - 1860 and 2460 Fertilizer Applicator
ASSEMBLY
COMPONENT INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Preparing For Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Coulter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Setting Coulter Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Gauge Wheel Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Supply Hose Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Coulter Injector Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Coulter Knife Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Orifice Installation (Coulters / Knives) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Orifice Installation (Coulters / Injectors) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Extending The Rear Light Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Slow Moving Vehicle Sign Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Spray Controller Console Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
23
Assembly - 1860 and 2460 Fertilizer Applicator
24
Assembly - 1860 and 2460 Fertilizer Applicator
COMPONENT INSTALLATION
Preparing For Assembly
AVOID INJURY OR DEATH
1860 and 2460 fertilizer applicators are shipped
without some components installed due to
transporting height and width restrictions.
•
•
Using the packing list, locate and count the
individual components and verify that you have
received the correct number of each component.
Check all the components for damage. If any
components are damaged or missing, contact
your Farm King dealer.
Before you leave the operator’s position:
• Always park on a flat level surface.
• Place all controls in NEUTRAL.
• Engage the park brake.
• Stop the engine and remove the key.
• Wait for all moving parts to stop.
Park the tractor / equipment on a flat level surface.
Place all controls in neutral, engage the park brake, stop
the engine and wait for all moving parts to stop. Leave
the operator’s position.
AVOID INJURY OR DEATH
Wear safety glasses to prevent eye injury when any
of the following conditions exist:
AVOID INJURY OR DEATH
•
When fluids are under pressure.
•
Flying debris or loose material is present.
•
Engine is running.
•
Tools are being used.
Before moving the tractor, look in all directions and
make sure no bystanders, especially small children
are in the work area. Do not allow anyone between
the tractor and the equipment when backing up to
the equipment for connecting.
Connect the fertilizer applicator to the tractor. (See
“Connecting The Fertilizer Applicator To The Tractor” on
page 40.)
Move the tractor, fertilizer applicator and crates to an
area large enough that will allow the toolbar and wings to
be fully extended and sufficient clearance for forklift
access.
25
Assembly - 1860 and 2460 Fertilizer Applicator
Figure 3
2
1
HIGH PRESSURE FLUID HAZARD
B-0148
To prevent serious injury or death from high
pressure fluid:
Connect the Blue (field mode) and Red (transport mode)
marked hydraulic hoses (Items 1 & 2) [Figure 3].
•
NOTE: Do not connect the hydraulic hoses with
White (pump) markings.
•
•
Relieve pressure on system before repairing or
adjusting.
Wear proper hand and eye protection when
searching for leaks. Use wood or cardboard
instead of hands.
Keep all components in good repair.
Figure 4
1
•
•
Contain and dispose of any oil leakage in an
environmentally safe manner.
Thoroughly clean the quick couplers before
making connections. Dirt can quickly damage
the system.
NOTE: Make sure the quick couplers are fully
engaged. If the quick couplers do not fully
engage, check to see that the couplers are the
same size and type.
NOTE: Hydraulic hoses marked with two colored
markers (tape) is the pressure line. Hydraulic
hoses marked with single colored marker
(tape) is the return line.
B-0129
Open the toolbar transport lock valve (Item 1) [Figure 4]
on the left side of the hitch. Rotate the lever 1/4 turn
counterclockwise.
Move to the operator’s seat and start the engine. (See
“Entering And Leaving The Operator’s Position” on
page 39.)
Engage the tractor hydraulics. (See the tractor’s
operator’s manual for the correct procedure.)
Unfold the wings with “Fold / Unfold Circuit” (hydraulic
hoses with the “Red” markers). (See “Fold And Unfold
Wings” on page 44.)
Stop the engine, wait for all moving parts to stop and
leave the operator’s position.
26
Assembly - 1860 and 2460 Fertilizer Applicator
Figure 7
Figure 5
CLOSED
CLOSED
OPEN
1
1
B-0138
B-0138
B-0137
With wing transport lock valves (Item 1) [Figure 5]
closed, lower the toolbar with the “Raise / Lower Circuit”
(hydraulic hoses with the “Blue” markers), until the center
coulters are close to but not contacting the ground.
Slowly rotate the wing transport lock valve lever (Item 1)
[Figure 7] 1/4 turn counterclockwise to open the valve
and allow the wing to settle onto the stand (Item 1)
[Figure 6].
Place all controls in neutral, engage the park brake, stop
the engine and wait for all moving parts to stop. Leave the
operator’s position. (See “Entering And Leaving The
Operator’s Position” on page 39.)
NOTE: As the wing transport valve is being opened,
oil will be transferred back to the main lift
cylinders. The tractor may need to be started
and the toolbar lowered a few times to lower
and level the toolbar onto the stands.
Figure 6
Slowly rotate the opposite wing transport lock valve lever
1/4 turn counterclockwise to open the valve and allow the
opposite wing to settle onto the second stand.
Move to the operator’s seat and start the engine. (See
“Entering And Leaving The Operator’s Position” on
page 39.)
Engage the tractor hydraulics. (See the tractor’s
operator’s manual for the correct procedure.)
1
B-0168
Place stands (Item 1) [Figure 6] under the wing(s) frame
to support the wing(s) during assembly (both sides).
NOTE: Always use jack stands that are in good
condition and of adequate size to support the
fertilizer applicator wing(s).
NOTE: Verify that the stands are adjusted high
enough to support the wing(s) and keep the
installed coulters above the ground to prevent
coulter damage.
27
Assembly - 1860 and 2460 Fertilizer Applicator
Figure 9
Figure 8
CENTER OF TOOLBAR
1
3
2
B-0173
Locate the center of the toolbar. Measure out from the
center of the toolbar and place a mark at the desired
spacing (30”, 22”, 20”) [Figure 8].
B-0167
Install two u-bolts (Item 1) over the toolbar at each
marked location (30”, 22”, 20”). Align coulter mount (Item
2) with the u-bolts. Install lock nuts (Item 3) [Figure 9]
onto the u-bolts. Do not tighten lock nuts at this time.
Figure 10
When installing the coulters and gauge wheels, the
toolbar and wings must be level and supported.
1
2
Coulter Installation
3
Coulter installation may require two people.
B-0169
Remove cotter pin (Item 1). Loosen the two clamp set
screws (Item 2), then slide the shaft (Item 3) [Figure 10]
of the coulter assembly up, into the clamps.
28
Assembly - 1860 and 2460 Fertilizer Applicator
Figure 11
2
3
1
B-0170
Raise the coulter assembly and rotate 180° [Figure 11]
to the rear.
Adjust the coulter mount (Item 1) and u-bolts (Item 2)
[Figure 11] left / right and center the assembly on the
marked location to maintain the required spacing.
Tighten the four lock nuts (Item 3) [Figure 11] to securely
fasten the coulter mount to the toolbar.
NOTE: Do not overtighten the lock nuts / u-bolts.
Overtightening may cause structural damage
to the wing frame.
Continue installing the remaining coulters at each
marked location on the wings.
29
Assembly - 1860 and 2460 Fertilizer Applicator
Install mounting bracket (Item 2) into the top hole (Item 3)
and slot (Item 4) [Figure 13] on the gauge wheel mount
(from the back side of the toolbar / wing).
Setting Coulter Height
Figure 12
Install lock nuts on the two mounting bracket studs. Verify
the 8 in. (203 mm) spacing. Tighten the two lock nuts to
secure the gauge wheel mount to the toolbar / wing.
3 in. (76 mm)
Mount with the tires on the outside of mounting frame.
Figure 14
1
2
1
1
B-0176
Loosen the set screws (Item 1) [Figure 12], lower the
coulter shaft until the top of the shaft is 3” (76 mm) down
from the mounting bracket. Align the coulter front to back
and tighten the set screws.
B-0172
Gauge Wheel Installation
NOTE: Install the gauge wheels on the inward side of
the second to the last coulter assemblies on
the inner and outer wings (both sides).
Maintain 8 in. (203 mm) from the centers of the
gauge wheel mount and coulter mounting
frame.
Figure 13
3
1
4
2
B-0177
B-0171
Place the gauge wheel mount (Item 1) [Figure 13] on the
front of the toolbar / wing.
30
Adjust gauge wheel assembly until the wheel is on the
left side (in front of coulter assembly to the left). Slide the
gauge wheel (Item 1) into the gauge wheel mount to the
desired height and install hitch pin (Item 2) [Figure 14]
and retaining pin.
Continue installing the remaining gauge wheels at each
designated location on the toolbar / wings.
Assembly - 1860 and 2460 Fertilizer Applicator
Coulter Injector Alignment
Supply Hose Installation
Figure 16
1
Review the supply line routing on the installed
coulters or main toolbar before attaching lines to
inner wing coulters.
Figure 15
B-0155
1
2
B-0154
Loosen bolt (Item 1) [Figure 16] and align the injector
with coulter blade. Tighten bolt.
B-0153
Route the supply hose (Item 1) [Figure 15] behind the
coulter assembly, down to the knife / injector. Fasten in
place with cable ties.
Apply petroleum jelly to fittings and install hose onto the
adapter (Item 2) [Figure 15] and secure in place with
hose clamp.
31
Assembly - 1860 and 2460 Fertilizer Applicator
Coulter Knife Alignment
Orifice Installation (Coulters / Knives)
Loosen bolt (Item 1) [Figure 16] and align the knife with
coulter blade. Tighten bolt.
Figure 19
Figure 17
CORRECT
1
B-0179
B-0174
Loosen fitting (Item 1) [Figure 19] and disconnect.
WRONG
Install orifice for the desired application rate and travel
speed.
Connect and tighten fitting.
Orifice Installation (Coulters / Injectors)
Figure 20
B-0175
Knives should rub slightly on blade at bottom of knife
(CORRECT) [Figure 17].
Figure 18
1
1
B-0180
Install spray tip, I.E. TeeJet StreamJet tip into female
threads located at the bottom of the assembly (Item 1)
[Figure 20].
B-0179
Loosen the two bolts (Item 1) [Figure 18] and adjust
knife to rub slightly on blade. Tighten bolts.
32
Assembly - 1860 and 2460 Fertilizer Applicator
Extending The Rear Light Bar
Slow Moving Vehicle Sign Installation
Figure 21
Figure 22
1
1
2
1
2
1
B-0158
B-0158
Loosen the inner bolt (Item 1) [Figure 21] (both light
bars).
Fully swing the light bar out. The inner bolt (Item 1) will
align with a slot (Item 2) [Figure 21] on the outer end of
the rear tank support (both ends).
Tighten bolts, securing the light bars in the operation /
transporting position.
Remove the two bolts (Item 1) [Figure 22] and slow
moving vehicle sign.
Rotate the slow moving vehicle sign 180°, align mounting
holes and install bolts to secure the slow moving vehicle
sign in the operation position.
Spray Controller Console Installation
Install the spray controller console in the cab of the
tractor according to the manufacturers specifications.
(See the spray controller Installation and Operator’s
manual for the correct procedure.)
Review the spray controller operator’s manual provided
with fertilizer applicator for calibration and operating
instructions before operating the fertilizer applicator.
Mount speed device to unit. Connect input to controller
and calibrate.
Calibrate the system for the speed and rate desired. (See
the spray controller Operator’s manual for the correct
procedure.)
(See “NOZZLE SELECTION” on page 146.) and (See
“NOZZLE SPECIFICATIONS” on page 147.) for
additional information.
33
Assembly - 1860 and 2460 Fertilizer Applicator
34
Operation - 1860 and 2460 Fertilizer Applicator
OPERATION
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Pre - Operation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Break - In Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Tractor Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Entering And Leaving The Operator’s Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
INITIAL SET-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Connecting The Fertilizer Applicator To The Tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Spray Tank Vent Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Connecting Hydraulic Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Connecting Electrical Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
FERTILIZER APPLICATOR OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Leveling The Fertilizer Applicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Lower And Raise The Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Fold And Unfold Wings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Adjusting Toolbar Lower / Raise Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Wing Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Adjusting Wing Down-Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Adjusting Coulter Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Filling The Spray Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Filling Fresh Water Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
FIELD OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Pre-Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Spray System Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Operating The Fertilizer Applicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Operating Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
TRANSPORTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Transporting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
35
Operation - 1860 and 2460 Fertilizer Applicator
36
Operation - 1860 and 2460 Fertilizer Applicator
GENERAL INFORMATION
Pre - Operation Checklist
Before operating the fertilizer applicator for the first time
and each time thereafter, check the following items:
AVOID INJURY OR DEATH
Wear safety glasses to prevent eye injury when any
of the following conditions exist:
•
When fluids are under pressure.
•
Flying debris or loose material is present.
•
Engine is running.
•
Tools are being used.
Leaking fluids under pressure can enter the skin
and cause serious injury or death. Immediate
medical attention is required. Wear goggles. Use
cardboard to check for leaks.
6. Check condition of all hydraulic components for leaks.
Repair as required.
NOTE: Do not operate with hydraulic leaks.
1. Lubricate the equipment per the schedule outline in
the Maintenance Section. (See “SERVICE
SCHEDULE” on page 60.)
2. Check the fertilizer applicator hitch for damaged,
loose or missing parts. Repair as needed before
operation.
7. Check that all electrical connections are tight.
8. Check and tighten all wheel bolts to 420 ft.-lb. torque.
9. Check tire pressure. Inflate per manufacturer’s
specification.
3. Check the coulters and gauge wheels. Remove any
twine, wire or other material that has become
entangled.
4. Check condition of all chemical / fertilizer components
for pinching, crimps or leaks. Re-align as required.
Tighten fittings to correct leaks or replace
components. Straighten lines to eliminate pinching or
crimps.
NOTE: Do not operate with leaks.
5. Make sure that all guards and shields are in place,
secured and functioning as designed.
37
Operation - 1860 and 2460 Fertilizer Applicator
Break - In Checklist
Check and tighten all wheel bolts to their specified torque
after transporting for five (5) miles (11km).
Check the following mechanical items after 1 hour of
operation and again after 10 hours of operation:
1. Check that all electrical connections are tight.
Figure 23
4. Check condition of all chemical / fertilizer components
for pinching, crimps or leaks. Re-align as required.
Tighten fittings to correct leaks or replace
components. Straighten lines to eliminate pinching or
crimps.
5. Check for loose fasteners and hardware. Tighten as
required.
6. Check wheel bolts for tightness. Tighten to 420 ft.-lb.
torque.
7. Clean screen in line strainer.
8. Check the coulters and gauge wheels. Remove any
twine, wire or other material that has become
entangled.
9. Check condition of all hydraulic components for leaks.
Tighten fittings to correct leaks or replace
components. Do not operate with hydraulic leaks.
10. Check tire pressure. Inflate per manufacturer’s
specification.
B-0124
2. Check the fertilizer applicator hitch for damaged,
loose or missing parts [Figure 23]. Repair as needed
before operation.
3. Check condition of all hydraulic components for leaks.
Repair as required.
38
Operation - 1860 and 2460 Fertilizer Applicator
Tractor Requirements
Entering And Leaving The Operator’s Position
The 1860 and 2460 fertilizer applicators will require a
MFWD (Mechanical Front Wheel Drive) tractor (minimum
250 hp), three auxiliary hydraulic functions, Category IV
rated drawbar and a 7-Pin electrical connection.
Operate only on a pressure compensated, load
sensing or flow compensated closed center pump
system. Use of an open center tractor hydraulic
system will result in the hydraulic flow continuously
bypassing the relief valve resulting in an increase in
engine horse power requirement to turn the pump at
the relief valve pressure. This will overheat the oil
and the tractor very quickly.
Follow the instructions in your tractor’s operation
manual for the correct procedure.
Entering The Operator’s Position
Move to the operator’s position, start the engine and
release the parking brake.
Leaving The Operator’s Position
Some older model tractors may have a detented
valve that will kick out when system pressure is
achieved. This valve must be over-ridden. The valve
must remain in detented position during field
operations. Maintaining pressure will allow the
system to keep the applicator functioning as
desired.
AVOID INJURY OR DEATH
Before you leave the operator’s position:
• Always park on a flat level surface.
• Place all controls in NEUTRAL.
• Engage the park brake.
• Stop the engine and remove the key.
• Wait for all moving parts to stop.
Park the tractor / equipment on a flat level surface.
Place all controls in neutral, engage the park brake, stop
the engine and wait for all moving parts to stop. Leave the
operator’s position.
39
Operation - 1860 and 2460 Fertilizer Applicator
INITIAL SET-UP
Figure 24
Connecting The Fertilizer Applicator To The Tractor
Always inspect the tractor’s drawbar and fertilizer
applicator hitch before connecting. See the tractor’s
owner’s manual.
1
Enter the operator’s position. (See “Entering The
Operator’s Position” on page 39.)
Move the tractor into position in front of the fertilizer
applicator.
B-0181
Turn the jack handle (Item 1) [Figure 24] clockwise to
raise the hitch or counterclockwise to lower the hitch.
Lower or raise the fertilizer applicator hitch until aligned
with the tractor’s drawbar.
Move to the operator’s seat, start the engine and release
the parking brake.
AVOID INJURY OR DEATH
Before moving the tractor, look in all directions and
make sure no bystanders, especially small children
are in the work area. Do not allow anyone between
the tractor and the equipment when backing up to
the equipment for connecting.
Move the tractor backwards, aligning the drawbar hitch
pin hole with the fertilizer applicator hitch pin hole(s).
Stop the tractor and leave operator’s position.
Move the tractor backwards, aligning the drawbar with the
fertilizer applicator hitch.
NOTE: The jack may need to be lowered or raised for
proper alignment of the drawbar and hitch.
If the fertilizer applicator hitch needs to be adjusted, stop
the tractor when drawbar is just in front of the fertilizer
applicator hitch.
Leave the operator’s position. (See “Leaving The
Operator’s Position” on page 39.)
AVOID INJURY OR DEATH
Keep fingers and hands out of pinch points when
connecting and disconnecting equipment.
NOTE: Always use a hitch pin of adequate size and
strength and a retaining pin with a locking
device.
40
Operation - 1860 and 2460 Fertilizer Applicator
Figure 25
1
2
B-0134
Install the hitch pin (Item 1) [Figure 25] and retaining pin
to securely fasten the fertilizer applicator hitch to the
tractor drawbar.
Attach the safety chain (Item 2) [Figure 25] around the
drawbar.
Spray Tank Vent Length
Figure 26
1
2
B-0162
Remove cable tie (Item 1), pull the 2” vent hose (Item 2)
[Figure 26] towards the ground. Cut the hose, just above
ground level.
41
Operation - 1860 and 2460 Fertilizer Applicator
Connecting Hydraulic Hoses
To Connect:
Figure 27
1
2
4
HIGH PRESSURE FLUID HAZARD
To prevent serious injury or death from high
pressure fluid:
•
•
•
Relieve pressure on system before repairing or
adjusting.
Wear proper hand and eye protection when
searching for leaks. Use wood or cardboard
instead of hands.
Keep all components in good repair.
3
B-0145
Pull back on the collar of the female coupler, push
couplers together, release the collar when the couplers
are fully engaged and locked [Figure 27].
1. First Circuit (Red Tape): Wing Fold / Unfold.
2. Second Circuit (Blue Tape): Toolbar Raise / Lower.
3. Third Circuit (White Tape): Liquid Pump.
To Disconnect:
•
•
Contain and dispose of any oil leakage in an
environmentally safe manner.
Thoroughly clean the quick couplers before
making connections. Dirt can quickly damage
the system.
AVOID BURNS
NOTE: Make sure the quick couplers are fully
engaged. If the quick couplers do not fully
engage, check to see that the couplers are the
same size and type.
NOTE: Hydraulic hoses marked with a single colored
marker (tape) is the pressure line. Hydraulic
hoses marked with two colored markers
(tape) is the return line.
Hydraulic fluid, tubes, fittings and quick couplers
can get hot when running equipment. Be careful
when connecting and disconnecting quick couplers.
Pull back on the collar and pull the male coupler out to
disconnect.
Connecting Electrical Harness
Connect the fertilizer applicator’s electrical harness (Item
4) [Figure 27] to the tractor’s electrical system.
The tractor’s hydraulic flow to the pump circuit
(hydraulic hoses marked with White tape) will need
to be reduced to approximately 6 gpm (22.7 l) to
prevent exceeding system specifications.
42
Lower jack until weight of equipment is resting on tractor
drawbar. Pull lock pin on jack and rotate to storage
position and secure with lock pin.
NOTE: Store jack in fully raised position to avoid
contact with center coulter.
Operation - 1860 and 2460 Fertilizer Applicator
Figure 29
FERTILIZER APPLICATOR OPERATION
Leveling The Fertilizer Applicator
1
The fertilizer applicator frame must be adjusted
down or up until the fertilizer applicator is parallel
with the ground prior to operation.
2
Lower the toolbar. (See “Lower And Raise The Toolbar”
on page 44.)
B-0152
NOTE: The wings and toolbar should be in the
operating position before leveling the
fertilizer applicator frame.
Loosen the three clevis mounting bolts (Item 1) [Figure
29].
Figure 28
Figure 30
1
B-0152
With the fertilizer applicator attached to the tractor, lower
the jack from the transport position. Raise the jack until
the weight of the fertilizer applicator is on the jack. This
will allow the clevis mounting bolts to be loosened and
moved for leveling [Figure 28] (if required).
2
B-0182
Measure the distance (Items 1 & 2) [Figure 30] from the
ground to the bottom of the fertilizer applicator frame in
the two locations shown.
NOTE: The
two
measurements
should
be
approximately the same when the frame is
level.
Raise or lower the jack until the fertilizer applicator frame
is parallel with the ground. Raise or lower the clevis (Item
2) [Figure 28] and align the closest clevis mounting
holes with frame. Install the six bolts.
Tighten the three clevis mounting bolts to the correct
torque and raise the jack into the storage position.
43
Operation - 1860 and 2460 Fertilizer Applicator
Lower And Raise The Toolbar
Fold And Unfold Wings
AVOID INJURY OR DEATH
Before operating the fertilizer applicator, look in all
directions and make sure no bystanders, especially
small children, are in the work area.
ELECTROCUTION HAZARD
To prevent serious
electrocution:
Always have the tractor / fertilizer applicator moving
forward at a minimum of 3 mph when lowering the
toolbar to minimize the side load on the coulters
when they contact the ground.
•
•
•
injury
or
death
from
Be aware of overhead powerlines.
Keep away from powerlines when transporting
or folding or unfolding wings.
Electrocution can occur without direct contact.
Lower the toolbar with the “Raise / Lower Circuit”
(hydraulic hoses with the “Blue” markers), until the center
coulters are close to, but not contacting the ground.
Never attempt to fold the wings unless the toolbar is
in the FULLY RAISED FIELD position. Failure to
comply may result in severe equipment damage.
To avoid serious injury or death, keep everyone
clear of machine when folding or extending wings.
AVOID INJURY OR DEATH
Before operating the fertilizer applicator, look in all
directions and make sure no bystanders, especially
small children are in the work area.
44
Operation - 1860 and 2460 Fertilizer Applicator
Adjusting Toolbar Lower / Raise Speed
Figure 31
CLOSED
OPEN
Adjustments to the toolbar's rate of drop needs to
made in field conditions, at field speeds.
Adjustments need to be made to all four (4) flow
control valves located at each of the short stroke
cylinders (one on each inner wing, one on each
outer wing). Flow control valve in Figure 32 may not
require adjustment, the other four will.
1
B-0130
B-0129
Open the toolbar transport lock valve (Item 1) [Figure 31]
on the left side of the hitch. Rotate the lever 1/4 turn
counterclockwise to open the valve.
Flow control, valve is set from the factory 1 1/2 turn
open from “finger tight”. FR12-23A-12T-N; 20 gpm; 5
turns clockwise to close.
Figure 33
Figure 32
CLOSED
OPEN
1
B-0127
1
B-0138
B-0137
NOTE: Adjust speed in 1/4 turn increments.
Rotate the wing transport lock valve levers (Item 1)
[Figure 32] (on the left and right inner wings) 1/4 turn
counterclockwise to open the valve.
Move to the operator’s seat and start the engine. (See
“Entering And Leaving The Operator’s Position” on
page 39.)
Adjust the tractor's hydraulic flow to the “Fold / Unfold”
and “Raise / Lower” circuits to 6 - 15 gpm flow. Engage
the tractor hydraulics. (See the tractor’s operator’s
manual for the correct procedure.)
Unfold the wings with the “Fold / Unfold Circuit” (hydraulic
hoses with the “Red” markers), until the wings are fully
extended.
Decreasing Speed
Loosen jam nut and turn the adjustment screw (Item 1)
[Figure 33] (clockwise) to decrease flow and speed.
Tighten jam nut.
Increasing Speed
Loosen jam nut and turn the adjustment screw (Item 1)
[Figure 33] (counterclockwise) to increase flow and
speed.
Tighten jam nut.
45
Operation - 1860 and 2460 Fertilizer Applicator
Wing Loading
Place all controls in neutral, engage the park brake, stop
the engine and wait for all moving parts to stop. Leave
the operator’s position.
Verify that the coulters are at the desired depth and that
the correct amount of down-load has been applied.
Check the soil conditions to determine the amount
of down force or load required on each wing to keep
the coulters at a consistent depth.
Enter the operator’s position, start the engine and
release the parking brake.
Move the tractor and fertilizer applicator to a level area in
the field.
Unfold the wings with the “Fold / Unfold Circuit”, until the
wings are fully extended.
Move the tractor and fertilizer applicator forward and
using the “Raise / Lower Circuit”, fully lower the toolbar.
Press and hold the “Raise / Lower Circuit” control to
place the circuit into the detent position to extend the
short section of the wing cylinders and apply down-load
on each wing section.
AVOID INJURY OR DEATH
Before you leave the operator’s position:
• Always park on a flat level surface.
• Place all controls in NEUTRAL.
• Engage the park brake.
• Stop the engine and remove the key.
• Wait for all moving parts to stop.
46
NOTE: If the down-load pressure needs to be
increased or decreased, use the pressure
relief valves on the center of the toolbar to
adjust the pressure. (See “Adjusting Wing
Down-Load” on page 47.)
Operation - 1860 and 2460 Fertilizer Applicator
Adjusting Wing Down-Load
NOTE: Use the relief valves and gauges to set wing
down-load to provide consistent application
depth of 2” to 3” (50 - 75 mm).
Figure 34
3
4
2
1
B-0127
NOTE: Adjust down-load
increments.
pressure
in
1/4
turn
NOTE: Adjust down-load pressure with “Raise /
Lower” circuit in the “detent” position.
Inner Wings
Loosen jam nut and turn the adjustment screw (Item 1)
[Figure 34] clockwise to increase pressure and download. Turn counterclockwise to decrease pressure and
down-load.
Monitor the inner wing gauge (Item 2) [Figure 34] while
adjusting down-load pressure.
Tighten jam nut.
Outer Wings
Loosen jam nut and turn the adjustment screw (Item 3)
[Figure 34] clockwise to increase pressure and download. Turn counterclockwise to decrease pressure and
down-load.
Monitor the outer wing gauge (Item 4) [Figure 34] while
adjusting pressure and down-load.
Tighten jam nut.
47
Operation - 1860 and 2460 Fertilizer Applicator
Coulter Adjustment
Adjusting Coulter Depth
Figure 35
It is recommended that the coulters are set so the
injectors or knives place the fertilizer 2” to 3” (50 75 mm) below the soil surface.
1
Enter the operator’s position, start the engine and
release the parking brake.
1
Move the tractor and fertilizer applicator to a level area in
the field.
Engage the tractor hydraulics. (See the tractor’s
operator’s manual for the correct procedure.)
Unfold and fully extend the wings. (See “Fold And Unfold
Wings” on page 44.)
B-0176
Loosen set screws (Item 1) [Figure 35] and move the
coulter assembly up or down to the desired depth.
Tighten the set screws.
Adjust individual coulters as needed to obtain the desired
depth.
Gauge Wheel Adjustment
Always have the tractor moving forward at a
minimum of 3 mph or more when lowering the
toolbar to prevent damage to the coulters.
Figure 36
1
Move the tractor and fertilizer applicator forward and fully
lower the toolbar. (See “Lower And Raise The Toolbar” on
page 44.)
2
Place all controls in neutral, engage the park brake, stop
the engine and wait for all moving parts to stop. Leave
the operator’s position.
Verify that the coulters, injectors or knives
approximately 2” to 3” below the soil surface.
are
B-0172
NOTE: If the coulter assemblies need to be adjusted,
the toolbar will need to be raised to relieve the
pressure to allow for adjustment up or down.
Remove pin (Item 1) and move the gauge wheel
assembly (Item 2) [Figure 36] up or down to the desired
height. Install the pin.
Enter the operator’s position, start the engine, engage
the tractor hydraulics and raise the toolbar (if required).
Adjust individual gauge wheels as needed to obtain the
desired height.
Leave the operator’s position (if required).
NOTE: Adjust all gauge wheel assemblies to the
same setting.
48
Operation - 1860 and 2460 Fertilizer Applicator
Filling The Spray Tank
Do not spill chemicals on skin or clothing. If
chemicals are spilled, remove contaminated
clothing immediately and wash skin (and clothing)
thoroughly with soap and water. Wash hands and
face with soap and water and change clothing after
spraying.
CHEMICAL HAZARD
To prevent serious injury or death:
WEAR PERSONAL PROTECTIVE EQUIPMENT
•
Do not allow chemical or solution to touch skin.
Some chemicals can be absorbed through the
skin.
•
Wear rubber gloves and protective gear at all
times.
Always read the label before using chemicals.
Follow the instructions from the chemical
manufacturer on how to select, use and handle each
chemical. Note protection information each time
before opening the container.
Park the tractor / equipment on a flat level surface.
DON’T BREATH VAPOR
•
Avoid chemical splash and vapor. Keep others
away.
•
Do not breathe vapor.
•
Wear proper respirator when working with
chemicals.
•
Chemicals can be toxic.
Place all controls in neutral, engage the park brake, stop
the engine and wait for all moving parts to stop. Leave
the operator’s position. (See “Entering And Leaving The
Operator’s Position” on page 39.)
DON’T INGEST CHEMICAL
•
If in eyes or mouth, read manufacturer’s
instructions and follow them exactly.
•
Seek immediate medical attention.
•
A poison control number is usually inside the
front cover of your telephone book.
Add chemical solution to the spray tank according
to the manufacturer’s recommendations.
49
Operation - 1860 and 2460 Fertilizer Applicator
Figure 39
Figure 37
1
1
B-0183
Remove fill cap (Item 1) [Figure 37].
Figure 38
2
B-0161
1
Open tank valve (Item 1) [Figure 39].
Fill the spray tank to the desired level.
Monitor the rear sight gauge while filling the spray tank.
Do not over-fill.
Install the fill hose (Item 1) [Figure 38].
Once the spray tank has been filled to the desired level,
close the tank valve and the fill valve and disconnect the
fill hose.
Open fill valve (Item 2) [Figure 38].
Install fill cap (Item 1) [Figure 37].
B-0160
50
Operation - 1860 and 2460 Fertilizer Applicator
FIELD OPERATION
Filling Fresh Water Tank
Pre-Operation
Move the tractor and fertilizer applicator to a level area in
the field. (See “TRANSPORTING” on page 55.)
Always use clean, fresh water when filling the fresh
water tank.
Engage the tractor hydraulics. (See the tractor’s
operator’s manual for the correct procedure.)
Figure 40
Unfold and fully extend the wings. (See “Fold And Unfold
Wings” on page 44.)
1
Always have the tractor moving forward at a
minimum of 3 mph or more when lowering the
toolbar to prevent damage to the coulters.
B-0184
Remove fill cap (Item 1) [Figure 40].
Fill fresh water tank with clean fresh water whenever
rinse water has been used (Do not allow tank to run low
on fresh water). Install fill cap.
NOTE: Use water from fresh water tank to clean,
rinse or wash anything that has become
contaminated.
Move the tractor and fertilizer applicator forward and fully
lower the toolbar. (See “Lower And Raise The Toolbar” on
page 44.)
Place all controls in neutral, engage the park brake, stop
the engine and wait for all moving parts to stop. Leave
the operator’s position.
Verify that the coulters, injectors or knives
approximately 2” to 3” below the soil surface.
are
Adjust coulters as needed to obtain the desired depth.
(See “Adjusting Coulter Depth” on page 48.)
Adjust wing down-load as needed to maintain the desired
depth. (See “Adjusting Wing Down-Load” on page 47.)
Adjust toolbar speed (if required). (See “Adjusting
Toolbar Lower / Raise Speed” on page 45.)
51
Operation - 1860 and 2460 Fertilizer Applicator
Wet Test
Spray System Test
Add approximately 300 gallons of clean water to the
spray tank. (See “Filling The Spray Tank” on page 49.)
Inspect the system for leaks. Repair as needed before
operating fertilizer applicator.
Review the spray controller operator’s manual and
be familiar with spray controller calibration and
operation before starting.
Verify that there is liquid in the pump vent line.
NOTE: Testing the spray system will require a
minimum of two people.
The pump must be filled with liquid during operation
to cool the seals. Without liquid to cool the seals,
pump failure will occur immediately.
Dry Test
Figure 41
NOTE: Maximum hydraulic flow for the pump is 11
gpm. Start with 5 gpm hydraulic flow and
increase / decrease as needed.
Enter the operator’s position, start the engine and
release the parking brake.
Engage the tractor hydraulics. (See the tractor’s
operator’s manual for the correct procedure.)
Turn the spray controller “ON”.
Place the spray controller in “TEST” mode.
Turn all five wing section switches “ON”.
Verify that the pump is flooded and vent line is filled with
fluid.
1
B-0195
One person will need to enter the operator’s position and
turn the tractor ignition switch to the “ON” position (Do
Not start engine.)
Turn the spray controller “ON”.
Engage spray pump hydraulic circuit (White markers) and
place into “detent” position. (See the tractor’s operator’s
manual for the correct procedure.)
Operate the spray pump for one minute to flush debris
from supply lines (If required). Turn off the pump by
moving the hydraulic control to the “float” position.
Determine targeted GPM flow rate.
Press wing section switches on the controller, one at a
time and operate each of the five manifold valves (Item 1)
[Figure 41].
Select and install properly sized orifices / tips. Perform a
“catch test” to verify application rate.
Second person will need to verify that each manifold
valve fully opens and closes. Also verify that the correct
switch on the controller is operating the correct section
manifold valve.
Drain system and clean the line strainer screen.
52
Inspect spray system components for leaks, loose fittings
and possible pinch points. Tighten loose fittings.
Operation - 1860 and 2460 Fertilizer Applicator
Operating The Fertilizer Applicator
Adjust toolbar lower / raise speed (If required). (See
“Adjusting Toolbar Lower / Raise Speed” on page 45.)
Always have the tractor moving forward at a
minimum of 3 mph or more when lowering the
toolbar to prevent damage to the coulters.
IDEAL OPERATION - Use the tractor's hydraulics to
lower and raise the toolbar. To lower, simply move
the tractor's hydraulic control to the detent position.
To raise, hold the control until the toolbar is fully
raised.
Enter the operator’s position, start the engine and
release the parking brake.
Engage the tractor hydraulics. (See the tractor’s
operator’s manual for the correct procedure.)
Figure 42
Drive the tractor and fertilizer applicator forward, towards
the starting point.
As the front tires of the tractor make contact with the field
/ rows (starting point), fully lower the toolbar by placing
the “Raise / Lower Circuit” switch directly into detent.
NOTE: Placing the “Raise / Lower Circuit” switch into
detent will maintain constant down pressure
during the application process.
Engage the spray pump and turn on the sectional control
valves using the spray controller to start application
process.
As the tractor approaches the end of the field / rows, turn
the sectional control valves “Off” and fully raise the
toolbar.
PREVENT COULTER DAMAGE
B-0188
Fully raise the toolbar [Figure 42].
Always fully raise the toolbar before turning the
tractor and fertilizer applicator and when moving the
tractor and fertilizer applicator to starting point in
the field.
Move the tractor and fertilizer applicator to the starting
area in the field.
Align the tractor and fertilizer applicator with field / rows.
Align the tractor and fertilizer applicator with next
application area.
As the front tires of the tractor make contact with the field
/ rows (next application area), fully lower the toolbar and
place the “Raise / Lower Circuit” switch into detent.
53
Operation - 1860 and 2460 Fertilizer Applicator
Continue the application process until the desired area /
field is complete.
Always flush spray tank and system with fresh water
before leaving the application area / field.
Stop the tractor and fertilizer applicator on a level surface
in the field.
Figure 43
B-0191
If boom profile looks like outer wings are riding high,
increase down-load pressure [Figure 43]. (See
“Adjusting Wing Down-Load” on page 47.)
Figure 44
Place all controls in neutral, engage the park brake, stop
the engine and wait for all moving parts to stop. Leave
the operator’s position.
Clean the spray tank. (See “Cleaning The Spray Tank” on
page 63.)
Place the toolbar and wings in the transport position.
(See “TRANSPORTING” on page 55.)
Operating Guidelines
•
Toolbar level, across all sections when engaged on
level ground.
•
Gauge wheels on wings should carry the weight of
wing.
B-0192
If boom profile looks like outer wings are riding low,
decrease down-load pressure [Figure 44]. (See
“Adjusting Wing Down-Load” on page 47.)
Figure 45
Increase down pressure if wheel appears to be
floating.
Decrease down pressure if wheel appears to be
pushing.
•
•
Changes in air temperature, hydraulic oil temperature
and field conditions (soil type, moisture, crop, etc.)
may affect operating performance of hydraulic
functions and require adjustments.
B-0193
If boom profile looks like inner wings are riding high,
increase down-load pressure [Figure 45]. (See
“Adjusting Wing Down-Load” on page 47.)
Figure 46
Boom adjustments.
Adjust outer wing down-load pressure first.
B-0194
If boom profile looks like inner wings are riding low,
decrease down-load pressure [Figure 46]. (See
“Adjusting Wing Down-Load” on page 47.)
54
Operation - 1860 and 2460 Fertilizer Applicator
TRANSPORTING
Figure 47
Requirements
Always comply with federal, state, local and provincial
laws regarding the transport of farm equipment on pubic
roadways.
Never exceed 20 mph (32 kph).
B-0204
Fully raise the toolbar into the field position [Figure 47].
(See “Lower And Raise The Toolbar” on page 44.)
Use of an unapproved hitch or tractor / tow vehicle
can result in loss of control, leading to serious
injury or death.
Tractor / tow vehicle and hitch must have the rated
capacity to tow equipment.
Verify that the tractor / tow vehicle is approved for
transporting the equipment and that the equipment is
securely attached to the tractor / tow vehicle.
Never attempt to fold the wings unless the toolbar is
in the FULLY RAISED FIELD position. Failure to
comply may result in severe equipment damage.
Fold wings. (See “Fold And Unfold Wings” on page 44.)
Verify safety chain is installed and properly connected
before transporting equipment.
Verify that the SMV (Slow Moving Vehicle) emblem, all
lights and reflectors are clean and visible.
LOCK
UNLOCK
Enter the operator’s position, start the engine and
release the parking brake.
Engage the tractor hydraulics. (See the tractor’s
operator’s manual for the correct procedure.)
PREVENT SERIOUS INJURY OR DEATH
Close (Lock) all transport lock valves before
transporting fertilizer applicator.
55
Operation - 1860 and 2460 Fertilizer Applicator
Transporting Guidelines
Figure 48
OPEN
CLOSED
AVOID SERIOUS INJURY OR DEATH
DO NOT transport a loaded fertilizer applicator on
public roadways. Excess weight will greatly
increase tractor stopping distance and may cause
the operator to lose control of the tractor or tow
1
B-0129
B-0130
Close the toolbar transport lock valve (Item 1) [Figure
48].
Figure 49
OPEN
1
B-0138
Close the wing transport lock valves (Item 1) [Figure 49].
Do not move or transport the fertilizer applicator
unless toolbar and wing lock valves are in the
closed (locked) position.
56
TRAVEL SPEED - Acceptable travel speed.
WEIGHT RATIO - Weight of fully equipped or loaded
implement(s) relative to weight of tractor / tow vehicle.
CLOSED
B-0137
The ratio of the tractor / tow vehicle weight to the loaded
equipment weight plays an important role in defining
acceptable travel speed.
TRAVEL SPEED
WEIGHT RATIO
Up to 20 mph (32 kph)
1 to 1 (or less)
Up to 10 mph (16 kph)
2 to 1 (or less)
DO NOT TOW
More than 2 to 1
Maintenance - 1860 and 2460 Fertilizer Applicator
MAINTENANCE
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
SERVICE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Maintenance Intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
LUBRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Cleaning The Spray Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Cleaning The Line Strainer Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Cleaning The Fertilizer Applicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
SAFETY SIGN (DECAL) INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
STORAGE AND RETURN TO SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Return To Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
57
Maintenance - 1860 and 2460 Fertilizer Applicator
58
Maintenance - 1860 and 2460 Fertilizer Applicator
TROUBLESHOOTING
Chart
Instructions are necessary before operating or servicing equipment. Read and understand the
Operator’s and Parts Manual and safety signs (decals) on equipment. Follow warnings and
instructions in the manuals when making repairs, adjustments or servicing. Check for correct
function after adjustments, repairs or service. Untrained operators and failure to follow instructions
can cause injury or death.
NOTE: If a problem is encountered that is difficult to solve, even after having read through this troubleshooting
section, please call your local distributor, dealer or factory. Before you call, please have this Operator’s
And Parts Manual and the serial number of your machine at hand.
PROBLEM
CAUSE
CORRECTION
Wings will not extend.
Lock valve is closed.
Open lock valve.
Applicator will not turn on.
No power.
Connect power line to 12 volt power
source in tractor cab.
Line valve is closed.
Open line valve.
Filter screen is plugged.
Remove filter and clean screen.
Orifice / tip plugged.
Remove and clean or replace orifice.
Check valve plugged.
Remove and clean or replace check
valve.
Filter screen is plugged.
Remove filter and clean screen.
Spray line loose or disconnected.
Check spray line connections.
Spray line cut or damaged.
Repair or replace spray line.
Down-load pressure too low.
Increase down-load pressure to the
inner or outer wing as needed.
Gauge wheel is set too low.
Raise gauge wheel(s) as needed.
Down-load pressure too high.
Decrease down-load pressure to the
inner or outer wing as needed.
Gauge wheel is set too high.
Lower gauge wheel(s) as needed.
Flow monitor ball gauges not even.
Coulter does not penetrate the
ground.
Coulter penetrates too far into the
ground.
59
Maintenance - 1860 and 2460 Fertilizer Applicator
SERVICE SCHEDULE
Maintenance Intervals
Maintenance work must be done at regular intervals. Failure to do so will result in excessive wear and early failures.
The service schedule is a guide for correct maintenance of the Fertilizer Applicator.
Instructions are necessary before operating or servicing equipment. Read and understand the
Operator and Parts Manual and safety signs (decals) on equipment. Follow warnings and instructions
in the manuals when making repairs, adjustments or servicing. Check for correct function after
adjustments, repairs or service. Untrained operators and failure to follow instructions can cause
injury or death.
SERVICE PROCEDURES
#
DESCRIPTION
Winterize
Clean
Lube
Change
Cover
Drain
Daily Maintenance (or every 8 hours)
1
Fresh Water Tank
•
2
Coulter Lower Parallel Arm
•
3
Coulter Pivots
•
•
Weekly (or every 50 hours)
4
Line Strainer Screen
5
Outer Wing Ball Joints
•
•
Every 250 hours
6
Wheel Bearings (Running gear and
gauge wheels)
•
7
Coulter Hub Bearings
•
Annually (or every 500 hours)
60
8
Spray Tank
•
9
Machine
•
•
10
Spray Monitor
•
•
•
Locations
Maintenance - 1860 and 2460 Fertilizer Applicator
LUBRICATION
Locations
Recommendations
Always use a good quality multi-purpose / lithium base
grease when lubricating the equipment.
Do not over-grease bearings. Greasing too often can
damage seals and lead to premature bearing failure.
Fluid such as engine oil, hydraulic fluid, coolants,
grease, etc. must be disposed of in an
environmentally safe manner. Some regulations
require that certain spills and leaks on the ground
must be cleaned in a specific manner. See local,
state and federal regulations for the correct
disposal.
Lubricate the following grease locations EVERY 8
HOURS:
Figure 50
Only sealed bushings are used on the applicator. Do
not over-grease.
•
Always use a hand-held grease gun.
•
Clean fitting before greasing, to avoid injecting dirt
and grit.
•
Replace and repair broken fittings immediately.
•
If fittings will not take grease, remove and clean
thoroughly. Replace fitting if necessary.
2
1
B-0166
Apply two pumps of grease to the coulter lower parallel
arm (Item 1) [Figure 50].
Figure 51
2
1
B-0165
Apply two pumps of grease to the coulter pivots (Item 1)
[Figure 51].
61
Maintenance - 1860 and 2460 Fertilizer Applicator
Lubricate the following grease locations EVERY 50
HOURS:
Figure 54
2-3
Figure 52
2-3
1
1
B-0163
1
B-0144
Apply two - three pumps of grease to the wing fold
bushings (Item 1) [Figure 52] on the PTO driveline.
Lubricate the following grease locations EVERY 250
HOURS:
Figure 53
2
1
B-0185
Apply two pumps of grease to the gauge wheel hubs
(Item 1) [Figure 53].
62
Apply two - three pumps of grease to the wheel bearings
(Item 1) [Figure 54].
Maintenance - 1860 and 2460 Fertilizer Applicator
CLEANING
The tank and system must be emptied of chemical
mixture and flushed with clean water before
servicing
the
spray
system
or
spraying
components.
CHEMICAL HAZARD
To prevent serious injury or death:
WEAR PERSONAL PROTECTIVE EQUIPMENT
•
Do not allow chemical or solution to touch skin.
Some chemicals can be absorbed through the
skin.
•
Wear rubber gloves and protective gear at all
times.
Do not spill chemicals on skin or clothing. If
chemicals are spilled, remove contaminated
clothing immediately and wash skin (and clothing)
thoroughly with soap and water. Wash hands and
face with soap and water and change clothing after
spraying.
DON’T BREATH VAPOR
•
Avoid chemical splash and vapor. Keep others
away.
•
Do not breathe vapor.
•
Wear proper respirator when working with
chemicals.
•
Chemicals can be toxic.
DON’T INGEST CHEMICAL
•
If in eyes or mouth, read manufacturer’s
instructions and follow them exactly.
•
Seek immediate medical attention.
•
A poison control number is usually inside the
front cover of your telephone book.
Rinse and clean any exterior surfaces and
components immediately if any liquid fertilizer spills
or leaks occur.
Cleaning The Spray Tank
Fill spray tank approximately half full, with clean water.
(See “Filling The Spray Tank” on page 49.)
Engage spray pump and flush out through the nozzles.
Add a proper cleaning agent and fill spray tank
approximately half full one more time.
Engage spray pump and flush out through the nozzles.
Fill spray tank approximately half full, with clean water,
engage spray pump and flush out through the nozzles for
the final rinse.
63
Maintenance - 1860 and 2460 Fertilizer Applicator
Cleaning The Line Strainer Screen
SAFETY SIGN (DECAL) INSTALLATION
Clean the line strainer screen every 50 hours of
operation.
Procedure
When replacing safety signs (decals),
temperature must be above 10° C (50° F).
the
The tank and system must be emptied of chemical
mixture and flushed with clean water before
servicing
the
spray
system
or
spraying
components.
•
Remove all portions of the damaged safety sign
(decal).
Figure 55
•
Thoroughly clean the area with glass cleaner.
Removing all adhesive residue.
•
Allow the area to dry completely before installing the
new safety sign (decal).
•
Position the safety sign (decal) in the correct location.
Remove a small portion of the backing paper on the
safety sign (decal).
•
Press on the safety sign (decal) where the backing
paper has been removed.
•
Slowly remove the remaining backing paper, pressing
on the safety sign (decal) as the backing paper is
removed.
•
Using the backing paper, pressing firmly, move the
backing paper over the entire safety sign (decal) area.
2
1
B-0186
Loosen and remove the line strainer canister (Item 1)
[Figure 55] by hand (do not use a wrench).
Remove screen (Item 2) [Figure 55] and clean from the
inside with clean water.
Inspect the screen for holes or tears. If the screen is
damaged, replace the screen.
Install screen and line strainer canister. Hand tighten the
line strainer canister (do not use a wrench).
Cleaning The Fertilizer Applicator
Clean and rinse all exterior surfaces and components
with clean water and cleaning agent to prevent corrosion.
64
NOTE: Small air pockets can be pierced with a pin
and smoothed out using the piece of the
backing paper.
Maintenance - 1860 and 2460 Fertilizer Applicator
STORAGE AND RETURN TO SERVICE
Storage
Sometimes it may be necessary to store your Farm King
fertilizer applicator for an extended period of time. Below
is a list of items to perform before storage.
•
Touch up all paint nicks and scratches to prevent
rusting.
•
Place the equipment in a dry protected shelter.
NOTE: If a dry protected shelter is not available,
cover with a waterproof tarp and tie down
securely.
•
Place the equipment flat on the ground.
•
Support the jack / frame with planks if required.
Return To Service
DO NOT permit children to play on or around the
stored machine.
•
Add 20 gal (75 liters) of clean water to the fertilizer
tank and flush out toolbar / wings. Repeat three times.
•
Thoroughly wash the machine with a pressure washer
or water hose to remove all dirt, mud, debris or
residue.
•
Remove knives, injectors and orifices from the coulter
assembly. Wash thoroughly. Apply a thin layer of
grease to coulter blades/knives and exposed cylinder
shafts to prevent rust.
•
Winterize with RV antifreeze.
•
Lubricate all bushings to remove any water residue
from washing.
•
Remove any material that has become entangled
around any moving part.
•
Cover the flow monitors with an opaque material
(lawn/leaf garbage bag) to prevent UV damage.
•
Raise and fold the toolbar and wings into their fully up
and retracted configuration.
•
Close the three valves in the wing lock hydraulic
circuits.
•
Clean, flush, drain and cover spray monitors to
protect from UV exposure.
•
Place hydraulic hoses and 7-pin connector in the
storage brackets.
•
Inspect the hitch and all welds on the equipment for
wear and damage.
•
Check for loose hardware, missing guards, or
damaged parts.
•
Check for damaged or missing safety signs (decals).
Replace if necessary.
•
Replace worn or damaged parts.
After the Farm King fertilizer applicator has been in
storage, it is necessary to follow a list of items to return
the equipment to service.
•
Be sure all shields and guards are in place.
•
Lubricate the equipment.
•
Connect to a tractor and operate equipment, verify all
functions operate correctly.
•
Check for leaks. Repair as needed.
65
Maintenance - 1860 and 2460 Fertilizer Applicator
66
Parts Identification - 1860 and 2460 Fertilizer Applicator
PARTS IDENTIFICATION
GENERAL PARTS INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
AXLE GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
FRAME GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
1860 & 2460 Green Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
1860 & 2460 Red Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
TANK SUPPORT GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
1860 & 2460 Green Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
1860 & 2460 Red Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
TANK SUPPORT FRONT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
1860 & 2460 Green Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
1860 & 2460 Red Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
TANK SUPPORT REAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
1860 & 2460 Green Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
1860 & 2460 Red Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
TANK ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
1860 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
TANK BAFFLE GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
1860 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
HAND / EYE WASH GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
1860 & 2460 Green Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
1860 & 2460 Red Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
TOOLBAR GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
1860 & 2460 Green Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
1860 & 2460 Red Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
FOLD LINKAGE GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
1860 & 2460 Green Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
1860 & 2460 Red Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
PRODUCT PLUMBING GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
67
Parts Identification - 1860 and 2460 Fertilizer Applicator
PRODUCT PUMP GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
PRODUCT PUMP ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
FORWARD PRODUCT PUMP GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
QUICK FILL GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
TOOLBAR PLUMBING GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Spray Monitors (1860 & 2460 Models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Spray Monitor Mount Assembly (Green Models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Spray Monitor Mount Assembly (Red Models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Spray Monitor Mount Assembly (Green Models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Spray Monitor Mount Assembly (Red Models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Injector & Knife Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
COULTER BRACKET GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
36 Row - 20” Spacing (60 Ft) 37 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
36 Row - 20” Spacing (60 Ft) 35 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
32 Row - 22” Spacing (60 Ft) 33 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
32 Row - 22” Spacing (60 Ft) 31 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
24 Row - 30” Spacing (60 Ft) 25 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
24 Row - 30” Spacing (60 Ft) 23 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
COULTER W / KNIFE GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
36 Row - 20” Spacing (60 Ft) 37 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
36 Row - 20” Spacing (60 Ft) 35 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
32 Row - 22” Spacing (60 Ft) 33 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
32 Row - 22” Spacing (60 Ft) 31 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
24 Row - 30” Spacing (60 Ft) 25 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
24 Row - 30” Spacing (60 Ft) 23 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
COULTER W / INJECT GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
36 Row - 20” Spacing (60 Ft) 37 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
36 Row - 20” Spacing (60 Ft) 35 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
32 Row - 22” Spacing (60 Ft) 33 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
32 Row - 22” Spacing (60 Ft) 31 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
24 Row - 30” Spacing (60 Ft) 25 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
24 Row - 30” Spacing (60 Ft) 23 Coulters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
68
Parts Identification - 1860 and 2460 Fertilizer Applicator
COULTER ASSEMBLY (STRAIGHT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
RH W / Knife . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
RH W / Injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
COULTER ARM ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
RH W / Injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
COULTER MOUNTING ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
RH W / Injector & RH W / Knife . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
GAUGE WHEEL GROUP LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
GAUGE WHEEL GROUP RH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
GAUGE WHEEL HUB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
TIRE / WHEEL SINGLE 380 / 90 R54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Cream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
TIRE / WHEEL SINGLE 380 / 90 R54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Yellow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
TIRE / WHEEL STRADDLE DUAL 320 / 90 R54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
20” Spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
TIRE / WHEEL STRADDLE DUAL 320 / 90 R54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
20” Spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
HUB ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
RAVEN 450 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
LIGHTING MARKING GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
HITCH GROUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
OUTER WING CYLINDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
69
Parts Identification - 1860 and 2460 Fertilizer Applicator
INNER FOLD CYLINDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
MAIN LIFT CYLINDER (LH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
MAIN LIFT CYLINDER (RH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
CONTROL VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
1860 & 2460 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
70
Parts - 1860 and 2460 Fertilizer Applicator
GENERAL PARTS INFORMATION
The parts identification section list descriptions, part numbers and quantities for all North America Base Model 1860
and 2460 fertilizer applicators. Contact your Farm King dealer for additional fertilizer applicator parts information.
AXLE GROUP
1860 & 2460 Models
3
4
1
2
5
4, 6, 7
NOTE:
Apply anti-seize to inside of tube before installing spindle.
88663737 R -
ITEM
1
2
3
4
5
6
7
PART NUMBER
88663910
88663909
88664705
88664704
09706701
SXFW-075-SAE-YZ
88663904
88664694
88660492
DESCRIPTION
AXLE WELDMENT, GREEN
AXLE WELDMENT, RED
HUB & SPINDLE ASSEMBLY 25K GREEN
HUB & SPINDLE ASSEMBLY 25K RED
CSHH G5 P 0.75” x 2.50”
FLATWASHER, 3/4 YLLW ZINC
NUT FLG, TP LCK, 3/4-10 GR5YZ
CSHH G8P 0.75” x 7.50”
LOCKNUT, 3/4” NI GR5 YZ
QTY
1
1
2
2
16
18
16
2
2
71
Parts - 1860 and 2460 Fertilizer Applicator
FRAME GROUP
1860 & 2460 Green Models
NOTE:
Apply anti-seize to inside of tube before installing pin (6).
1
22, 9
10
18
15
4
3, 11
7
8
16
17
6
13
14
12
3, 12
2
5
19
21
25
24
20
7
13
23
16
5
14
6
17
88663894 R C
72
Parts - 1860 and 2460 Fertilizer Applicator
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
PART NUMBER
88663880
88663882
SXLN-050-NI-YZ
88663884
88663886
88663670
88663890
88663702
88663897
88663612
88663898
00087997
88663764
88663763
88663762
88663760
88663765
88663730
88663779
88663793
88663794
SXNTFTL050138Y
SXFW-050-YZ
SXLN-038-NIYZ
88665281
DESCRIPTION
FRAME WELDMENT
BRACKET, HOSE GUARD,
LOCKNUT, 1/2” NYLON INSERT
REAR LIFT ARM GREEN, WELDMENT
FRONT LIFT ARM GREEN, WELDMENT
PIN, LIFT ARM FRONT TOP
FRONT LIFT ARM COLLAR
PLATE, SPACER PUMP
CSHH G5P 0.50” x 3.00”
PIN, HINGE INNER WING
CSHH G5P 0.50” x 3.50”
CSHH G5 P 0.50” x 5.00” 86505344
BUSHING, FRONT LIFT ARM FRONT
BUSHING, FRONT LIFT ARM REAR
BUSHING, TOOLBAR
BUSHING, CYLINDER CLEVIS
WASHER, THRUST LIFT ARM
WASHER, THRUST TOOLBAR
MOUNT, HYD VALVE ASSY
TOOLBAR STOP
SCREW, FH CS P 0.375” x 0.75”
NU, FLG TP LCK 1/2”-13 GR8-YZ
FLATWASHER, 1/2” YZ
LOCKNUT, 3/8” NYLON INSERT
BRACKET, RETAINER HOSE
QTY
1
2
12
2
2
2
2
1
2
2
4
8
2
2
4
4
4
4
1
2
8
2
4
2
2
73
Parts - 1860 and 2460 Fertilizer Applicator
FRAME GROUP (CONT’D)
1860 & 2460 Red Models
NOTE:
Apply anti-seize to inside of tube before installing pin (6).
1
22, 9
10
18
15
4
3, 11
7
8
16
17
6
13
14
12
3, 12
2
5
19
21
25
24
20
7
13
23
16
5
14
6
17
88663892 R
74
Parts - 1860 and 2460 Fertilizer Applicator
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
PART NUMBER
88663879
88663881
SXLN-050-NI-YZ
88663883
88663885
88663670
88663889
88663702
88663897
88663612
88663898
00087997
88663764
88663763
88663762
88663760
88663765
88663730
88663779
88663793
88663794
SXNTFTL050138Y
SXFW-050-YZ
SXLN-038-NIYZ
88665281
DESCRIPTION
FRAME WELDMENT
BRACKET, HOSE GUARD,
LOCKNUT, 1/2” NYLON INSERT
REAR LIFT ARM RED, WELDMENT
FRONT LIFT ARM RED, WELDMENT
PIN, LIFT ARM FRONT TOP
FRONT LIFT ARM COLLAR
PLATE, SPACER PUMP
CSHH G5P 0.50” x 3.00”
PIN, HINGE INNER WING
CSHH G5P 0.50” x 3.50”
CSHH G5 P 0.50” x 5.00” 86505344
BUSHING, FRONT LIFT ARM FRONT
BUSHING, FRONT LIFT ARM REAR
BUSHING, TOOLBAR
BUSHING, CYLINDER CLEVIS
WASHER, THRUST LIFT ARM
WASHER, THRUST TOOLBAR
MOUNT, HYD VALVE ASSY
TOOLBAR STOP
SCREW, FH CS P 0.375” x 0.75”
NU, FLG TP LCK 1/2”-13 GR8-YZ
FLATWASHER, 1/2” YZ
LOCKNUT, 3/8” NYLON INSERT
BRACKET, RETAINER HOSE
QTY
1
2
12
2
2
2
2
1
2
2
4
8
2
2
4
4
4
4
1
2
8
2
4
2
2
75
Parts - 1860 and 2460 Fertilizer Applicator
TANK SUPPORT GROUP
1860 & 2460 Green Models
5
3
6
8
1
4
2
7
88664849 R -
ITEM
1
2
3
4
5
6
7
8
76
PART NUMBER
88663942
88664832
88664857
88664858
SX12J
SX3EL34HB
SXHB-075
SXHB-075-90
DESCRIPTION
TANK SUPPORT ASSEMBLY FRONT, GREEN
TANK SUPPORT ASSEMBLY REAR, GREEN
HOSE SIGHT 3/4”
HOSE SIGHT 3/4”
CLAMP, 3/4” HOSE WORM SCREW
HOSE FITTING, 5/8” ELHB x 5/8” HB
HOSE BARB, 3/4” MPT x 3/4” HB POLY
HOSE BARB, 3/4” MPT x 3/4” HB
QTY
1
1
2
2
8
2
2
2
Parts - 1860 and 2460 Fertilizer Applicator
TANK SUPPORT GROUP (CONT’D)
1860 & 2460 Red Models
5
3
6
8
1
4
2
7
88664848 R -
ITEM
1
2
3
4
5
6
7
8
PART NUMBER
88663941
88663738
88664857
88664858
SX12J
SX3EL34HB
SXHB-075
SXHB-075-90
DESCRIPTION
TANK SUPPORT ASSEMBLY FRONT, RED
TANK SUPPORT ASSEMBLY REAR, RED
HOSE SIGHT 3/4”
HOSE SIGHT 3/4”
CLAMP, 3/4” HOSE WORM SCREW
HOSE FITTING, 5/8” ELHB x 5/8” HB
HOSE BARB, 3/4” MPT x 3/4” HB POLY
HOSE BARB, 3/4” MPT x 3/4” HB
QTY
1
1
2
2
8
2
2
2
77
Parts - 1860 and 2460 Fertilizer Applicator
TANK SUPPORT FRONT
1860 & 2460 Green Models
2
3
4
1
5
7
6
88663942 R A
ITEM
1
2
3
4
5
6
7
78
PART NUMBER
88663622
88663940
88664854
SXNTFTL062118Y
SXBUR031350500
SXLN-031-NIYZ
SXNUT-031YZ
DESCRIPTION
U-BOLT, 0.63 x 5.13 x 8.63 LG
TANK SUPPORT FRONT, GREEN WELDMENT
SIGHT GAUGE ASSEMBLY
NUT FLG, TP LCK, 5/8” GR8 YZ
U-BOLT, 5/16” x 3.50” x 5.0” ROUND GR2
LOCKNUT, 5/16” NYLON INSERT YZ
NUT, 5/16” NUT YZ
QTY
4
1
1
8
2
4
4
Parts - 1860 and 2460 Fertilizer Applicator
TANK SUPPORT FRONT (CONT’D)
1860 & 2460 Red Models
2
3
4
1
5
7
6
88663941 R A
ITEM
1
2
3
4
5
6
7
PART NUMBER
88663622
88663939
88664854
SXNTFTL062118Y
SXBUR031350500
SXLN-031-NIYZ
SXNUT-031YZ
DESCRIPTION
U-BOLT, 0.63 x 5.13 x 8.63 LG
TANK SUPPORT FRONT, RED WELDMENT
SIGHT GAUGE ASSEMBLY
NUT FLG, TP LCK, 5/8” GR8 YZ
U-BOLT, 5/16” x 3.50” x 5.0” ROUND GR2
LOCKNUT, 5/16” NYLON INSERT YZ
NUT, 5/16” NUT YZ
QTY
4
1
1
8
2
4
4
79
Parts - 1860 and 2460 Fertilizer Applicator
TANK SUPPORT REAR
1860 & 2460 Green Models
3
5
7
1
4
2
88664832 R A
ITEM
1
2
3
4
5
6
7
8
9
80
PART NUMBER
86505938
88663622
88663906
88664831
88664854
SX21294
SXBH0381005YZ
SXNTFTL038168YZ
SXNTFTL062118Y
DESCRIPTION
WASHER P, 0.406ID, 1.375OD, 0.083
U-BOLT, 0.63 x 5.13 x 8.63 LG
TANK SUPPORT REAR - GREEN WELDMENT
BRACKET, LIGHT BAR, RED
SIGHT GAUGE ASSEMBLY
MOUNT, CABLE TIE HEAVY DUTY
BOLT, 3/8” x 1” YZ
NUT FLG, TP LCK, 3/8” GR8 YZ
NUT FLG, TP LCK, 5/8” GR8 YZ
QTY
8
4
1
2
1
8
8
8
8
Parts - 1860 and 2460 Fertilizer Applicator
TANK SUPPORT REAR (CONT’D)
1860 & 2460 Red Models
3
5
7
1
4
2
88663738 R A
ITEM
1
2
3
4
5
6
7
8
9
PART NUMBER
86505938
88663622
88663905
88664831
88664854
SX21294
SXBH0381005YZ
SXNTFTL038168YZ
SXNTFTL062118Y
DESCRIPTION
WASHER P, 0.406ID, 1.375OD, 0.083
U-BOLT, 0.63 x 5.13 x 8.63 LG
TANK SUPPORT REAR - RED WELDMENT
BRACKET, LIGHT BAR, RED
SIGHT GAUGE ASSEMBLY
MOUNT, CABLE TIE HEAVY DUTY
BOLT, 3/8” x 1” YZ
NUT FLG, TP LCK, 3/8” GR8 YZ
NUT FLG, TP LCK, 5/8” GR8 YZ
QTY
8
4
1
2
1
8
8
8
8
81
Parts - 1860 and 2460 Fertilizer Applicator
TANK ASSEMBLY
1860 Models
1
6
2, 3, 4
7
5
88664667 R -
ITEM
1
2
3
4
5
6
7
82
PART NUMBER
88663783
88664553
88664555
88664554
SXMBF300BD
SXMBF220
88663650
88663651
DESCRIPTION
TANK BAFFLE ASSEMBLY 1800
LID TANK 16” POLY
STSTPH#10-24 x 0.625 86505618
GASKET LID TANK 16” POLY
BULKHEAD, 3”, BOLT, FLANGED, BD
MANIFOLD, 2” FP FLG, 2” FPT
TANK - 1800 GAL CREAM
TANK - 1800 GAL YELLOW
QTY
2
1
8
1
1
1
1
1
Parts - 1860 and 2460 Fertilizer Applicator
TANK ASSEMBLY (CONT’D)
2460 Models
1
5
2, 3, 4
7
6
88664668 R -
ITEM
1
2
3
4
5
6
7
PART NUMBER
88663782
88664553
88664554
88664555
SXMBF220
SXMBF300BD
88663652
88663653
DESCRIPTION
TANK BAFFLE ASSEMBLY 2400
LID TANK 16” POLY
GASKET LID TANK 16” POLY
STSTPH#10-24 x 0.625 86505618
MANIFOLD, 2” FP FLG, 2” FPT
BULKHEAD, 3”, BOLT, FLANGED, BD
TANK - 2400 GAL CREAM
TANK - 2400 GAL YELLOW
QTY
2
1
1
8
1
1
1
1
83
Parts - 1860 and 2460 Fertilizer Applicator
TANK BAFFLE GROUP
1860 Models
7
6
8
4
5
2
9
2
5
3
1
4
1
3
88663782 R -
ITEM
1
2
3
4
5
6
7
8
9
84
PART NUMBER
88663784
88663787
88663788
88663790
88663802
88663809
88663812
88663813
88663814
DESCRIPTION
BRACKET, BAFFLE LOWER SECT
BAFFLE CHANNEL LH WELDMENT
BAFFLE CHANNEL RH WELDMENT
BRACKET, UPPER BAFFLE 2400
RIB ADJUSTMENT WELDMENT
TANK RIB WELDMENT
BOLT, 3/8” x 1.50” UNC SS
WASHER, FENDER 3/8” STAINLESS
LOCKNUT, 3/8” NYLON INSERT SS
QTY
2
2
2
2
2
1
30
60
30
Parts - 1860 and 2460 Fertilizer Applicator
TANK BAFFLE GROUP (CONT’D)
2460 Models
6
9
5
8
6
4
2
7
2
4
3
1
1
3
88663783 R -
ITEM
1
2
3
4
5
6
7
8
9
PART NUMBER
88663784
88663787
88663788
88663802
88663809
88663789
88663814
88663813
88663812
DESCRIPTION
BRACKET, BAFFLE LOWER SECT
BAFFLE CHANNEL LH WELDMENT
BAFFLE CHANNEL RH WELDMENT
RIB ADJUSTMENT WELDMENT
TANK RIB WELDMENT
BRACKET, UPPER BAFFLE 1800
LOCKNUT, 3/8” NYLON INSERT SS
WASHER, FENDER 3/8” STAINLESS
BOLT, 3/8” x 1.50” UNC SS
QTY
2
2
2
2
1
2
28
56
28
85
Parts - 1860 and 2460 Fertilizer Applicator
HAND / EYE WASH GROUP
1860 & 2460 Green Models
7
1
10
2
4
5
3
6, 8, 9
88664968 R -
ITEM
1
2
3
4
5
6
7
8
9
10
86
PART NUMBER
88664963
88664964
88664965
88665009
SX014666
SXBH-031-075-5
SXBHF0381008YZ
SXFW-031-YZ
SXLW-031
SXNTFTL038168YZ
DESCRIPTION
PLATE, MOUNT HAND TANK
PLATE, BRACKET HAND TANK
SHEET MNT DECAL
TANK HAND EYE RINSE ASSEMBLY, YELLOW
BRACKET WELDMENT 9 GAL. TANK
BOLT, 5/16” x 0.750” GR5
BOLT, FLG, 3/8” x 1.00” GR8 YZ
WASHER, FLAT, 5/16” YZ
WASHER, LOCK, 5/16
NUT FLG, TP LCK, 3/8-16 UNC G8YZ
QTY
1
1
1
1
2
6
8
6
6
8
Parts - 1860 and 2460 Fertilizer Applicator
HAND / EYE WASH GROUP (CONT’D)
1860 & 2460 Red Models
7
1
10
2
4
5
3
6, 8, 9
88664988 R -
ITEM
1
2
3
4
5
6
7
8
9
10
PART NUMBER
88664963
88664964
88664965
88665010
SX014666
SXBH-031-075-5
SXBHF0381008YZ
SXFW-031-YZ
SXLW-031
SXNTFTL038168YZ
DESCRIPTION
PLATE, MOUNT HAND TANK
PLATE, BRACKET HAND TANK
SHEET MNT DECAL
TANK HAND EYE RINSE ASSEMBLY, CREAM
BRACKET WELDMENT 9 GAL. TANK
BOLT, 5/16” x 0.750” GR5
BOLT, FLG, 3/8” x 1.00” GR8 YZ
WASHER, FLAT, 5/16” YZ
WASHER, LOCK, 5/16
NUT FLG, TP LCK, 3/8-16 UNC G8YZ
QTY
1
1
1
1
2
6
8
6
6
8
87
Parts - 1860 and 2460 Fertilizer Applicator
TOOLBAR GROUP
1860 & 2460 Green Models
5
3
9
12,13
16
8
18
12,13
20
1
2
12,13
7
16
6
8
10
14,15
17
4 11
19
8
12,13
88663947 R B
88
Parts - 1860 and 2460 Fertilizer Applicator
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PART NUMBER
88663908
88663914
88663916
88663918
88663920
88663610
88663930
88663612
88663666
88663730
88663932
88663898
SXLN-050-NI-YZ
88663895
SXLN-038-NI-YZ
88663760
88663762
88663707
88663774
88663961
DESCRIPTION
TOOLBAR CENTER GREEN, WELDMENT
INNER WING LH, WELDMENT
INNER WING RH, WELDMENT
OUTER WING LH GREEN, WELDMENT
OUTER WING RH GREEN, WELDMENT
PIN, LINKAGE OUTER WING
FOLD LINKAGE GREEN, ASSEMBLY
PIN, HINGE INNER WING
PIN, LIFT ARM FRONT BOTTOM
WASHER, THRUST TOOLBAR
GREEN BALL MOUNT, ASSEMBLY
CSHH G5P 0.50” x 3.50”
LOCKNUT, 1/2” NYLON INSERT
CSHH G5P 0.38” x 3.00”
LOCKNUT, 3/8” NYLON INSERT
BUSHING, CYLINDER CLEVIS
BUSHING, TOOLBAR
GAUGE WHEEL RH, ASSEMBLY
GAUGE WHEEL LH, ASSEMBLY
CENTER GREEN BALL MNT, ASSEMBLY
QTY
1
1
1
1
1
2
2
10
2
12
4
24
24
4
4
6
4
2
2
1
89
Parts - 1860 and 2460 Fertilizer Applicator
TOOLBAR GROUP (CONT’D)
1860 & 2460 Red Models
5
3
9
12,13
16
8
18
12,13
20
1
2
12,13
7
16
6
8
10
14,15
17
4 11
19
8
12,13
88663946 R B
90
Parts - 1860 and 2460 Fertilizer Applicator
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PART NUMBER
88663907
88663913
88663915
88663917
88663919
88663610
88663696
88663612
88663666
88663730
88663729
88663898
SXLN-050-NI-YZ
88663895
SXLN-038-NI-YZ
88663760
88663762
88663707
88663774
88663960
DESCRIPTION
TOOLBAR CENTER RED, WELDMENT
INNER WING LH, WELDMENT
INNER WING RH, WELDMENT
OUTER WING LH RED, WELDMENT
OUTER WING RH RED, WELDMENT
PIN, LINKAGE OUTER WING
FOLD LINKAGE RED, ASSEMBLY
PIN, HINGE INNER WING
PIN, LIFT ARM FRONT BOTTOM
WASHER, THRUST TOOLBAR
RED BALL MOUNT, ASSEMBLY
CSHH G5P 0.50” x 3.50”
LOCKNUT, 1/2” NYLON INSERT
CSHH G5P 0.38” x 3.00”
LOCKNUT, 3/8” NYLON INSERT
BUSHING, CYLINDER CLEVIS
BUSHING, TOOLBAR
GAUGE WHEEL RH, ASSEMBLY
GAUGE WHEEL LH, ASSEMBLY
CENTER RED BALL MNT, ASSEMBLY
QTY
1
1
1
1
1
2
2
10
2
12
4
24
24
4
4
6
4
2
2
1
91
Parts - 1860 and 2460 Fertilizer Applicator
FOLD LINKAGE GROUP
1860 & 2460 Green Models
15
6
7
10
3
11
7
5
14
13
12
9
4
2
13
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
92
12
PART NUMBER
88663921
88663923
88663679
88663927
88663681
88663901
88663902
SXLN-038-NI-YZ
SXBH-038-275-5
88663669
88663680
88663761
88663760
SXBH0381005YZ
88663501
8
88663930 R -
DESCRIPTION
BRACKET, LINK DRIVER GREEN
BRACKET, LINK COUPLER GREEN
FLAG AND PIN LINKAGE WELDMENT
COLLAR, LINKAGE GREEN
BUSHING, FLAG LINKAGE
CSHH G5P 0.38” x 1.50”
WASHER, FENDER, 3/8”
LOCKNUT, 3/8” NYLON INSERT
BOLT HEX, 0.375” x 2.75” GR5 YZ
FLAG AND PIN WELDMENT
BUSHING, FLAG
BUSHING, FOLD LINKAGE
BUSHING, CYLINDER CLEVIS
BOLT, 3/8” x 1” YZ
OUTER WING LIFT CYLINDER
QTY
2
1
2
2
1
1
2
2
2
1
1
4
2
1
1
Parts - 1860 and 2460 Fertilizer Applicator
FOLD LINKAGE GROUP (CONT’D)
1860 & 2460 Red Models
15
6
7
10
3
11
7
5
14
13
12
9
4
2
13
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
12
PART NUMBER
88663911
88663922
88663679
88663926
88663681
88663901
88663902
SXLN-038-NI-YZ
SXBH-038-275-5
88663669
88663680
88663761
88663760
SXBH0381005YZ
88663501
8
88663696 R -
DESCRIPTION
BRACKET, LINK DRIVER RED
BRACKET, LINK COUPLER RED
FLAG AND PIN LINKAGE WELDMENT
COLLAR, LINKAGE RED
BUSHING, FLAG LINKAGE
CSHH G5P 0.38” x 1.50”
WASHER, FENDER, 3/8”
LOCKNUT, 3/8” NYLON INSERT
BOLT HEX, 0.375” x 2.75” GR5 YZ
FLAG AND PIN WELDMENT
BUSHING, FLAG
BUSHING, FOLD LINKAGE
BUSHING, CYLINDER CLEVIS
BOLT, 3/8” x 1” YZ
OUTER WING LIFT CYLINDER
QTY
2
1
2
2
1
1
2
2
2
1
1
4
2
1
1
93
Parts - 1860 and 2460 Fertilizer Applicator
PRODUCT PLUMBING GROUP
1860 & 2460 Models
19
11
7
13
8
6
3
20
18
5
16
2
4
12
1
3
6
18
19
17
8
15
7
11
1
10
9
14
15
88664755 R B
94
Parts - 1860 and 2460 Fertilizer Applicator
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PART NUMBER
88664761
88664778
88664779
88664780
88664781
88664782
SXFC100BJ
SXFC200BJ
SXM100BRB
SXM100BRB90
SXM100G
SXM200100BRB
SXM200100CPG
SXM200100TEE
SXM200BRB
SXM200BRB90
SXM200CR
SXTBC256
SXTBC256
SX150G
DESCRIPTION
CLAMP, T-BOLT 1.38” - 1.62”
HOSE 1”
HOSE 1”
HOSE 2”
HOSE 2”
HOSE 2”
CLAMP, 1”
CLAMP, 2” BANJO
HOSE BARB, 1” X 1” STRAIGHT
HOSE BARB, 1” FLANGE ELBOW
GASKET, FOR 1” FLANGED VALVE
HOSE BARB, 2” x 1” STRAIGHT
FLANGE, REDUCER 2” x 1”
TEE, 2” x 1” TEE
HOSE BARB, 2” FLG X 2” HB
HOSE BARB, 2” HB, 2” FLG, EL
CROSS, 2” STANDARD PORT FLG
CLAMP, T-BOLT 2 11/32 - 25/8
MANIFOLD 1-VALVE ASSY, 1” FLG
GASKET, FOR 2” FLANGED VALVE
QTY
6
1
2
1
1
2
7
10
2
3
7
1
2
2
6
2
1
8
5
10
95
Parts - 1860 and 2460 Fertilizer Applicator
PRODUCT PUMP GROUP
1860 & 2460 Models
41,42
42
43
18
17
25
33
32
1
10 2
42
7
5
5
2
4
7
5 7
3
12
2
5
9
39
21
2 4
37
5
7
11
7
6
40
4
3 4 2 38
13 14
16 15
13
15
29
7 5
6
4 8
5
7
9
18
17
18
17
7
5
34
7
5
29
27
7
5
28
33
19
20
35
26
88664673 R C
96
Parts - 1860 and 2460 Fertilizer Applicator
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
PART NUMBER
88663854
SX150G
SXM300200CPG
SXFC200BJ
SX300G
SXM300TEE
SXFC300BJ
SXM200100BRB
SX#20J
SXM200150MPT
SXM200100TEE
SXM200BRB
SX100G
88661393
SXFC100BJ
SXM100BRB
SXM300BRB
SXTBC350
88661663
88664681
SXMLST150H-50
SX600448
SX011612
88663840
88663702
SX200G
SXM220BRB90
SXFC220
SXTBC256
SX600333
SX600432
SX3A1814
SX4JM
SXMV300CF
SXHB025-90
SXK3150-025
88665312
SXM200MPT
SXM300CPG
SXM300CPG90
SXNTFTL038168YZ
00280260
SX21294
DESCRIPTION
PRODUCT PUMP, ASSEMBLY
GASKET, 2" FLANGED VALVE
MANIFOLD FITTING, 3” x 2” FULL
CLAMP, 2” BANJO
GASKET, 3” BANJO
TEE, 3” FLANGED
CLAMP, 3" BANJO
HOSE BARB, 2” x 1” STRAIGHT
CLAMP,1 1/4” x 1/2” STAINLESS
MANIFOLD, 2” x 1 1/2” MALE THREAD
TEE, 2” x 1” TEE
HOSE BARB, 2” FLG x 2” HB
GASKET, 1” COUPLING EPDM
VALVE, 1” 100# PRESS SPIKE
CLAMP, 1”
HOSE BARB, 1” x 1” STRAIGHT
HOSE BARB, 3” FLG x 3” HB, POLY
CLAMP, T-BOLT 3 1/2” - 3 - 13/16”
3” FLANGE x FLANGE SWEEP 90
MANIFOLD PRODUCT FWD, ASSEMBLY
STRAINER, FLANGED, 2” STD PORT
HOSE, 3” EPDM W/POLYHELIX FABR
HOSE, 1” 150# BLACK RUBBER
HOSE ASSY, 5/8” x 324”
PLATE, SPACER PUMP
GASKET, 2” COUPLING EPDM
MANIFOLD, 2” FLG x 2” HB
CLAMP, 2” SERIES WORM SCREW
CLAMP, T-BOLT 2 11/32 - 25/8
HOSE, 2” EPDM,150 PSI. AG HOSE
HOSE, 2” ENFORCER FERT SOL.
HOSEBARB, 1/8” x 1/4”, POLY
CLAMP, 1/4” x 5/16” STAINLESS
VALVE, 3” STD PORT MANIFOLD
HOSE BARB ELL, 1/4” MPT X 1/4” HB
HOSE, 1/4” VINYL REINFORCE CLEAR
ELBOW, 90 DEG, 1/8” STREET MALE & FEMALE
MANIFOLD, 2” FLG, 2” MPT
FLANGE, 3” MANIFOLD FI
MANIFOLD ELBOW, 3” x 3” FLANGE 90
NUT FLG, TP LCK, 3/8” GR8 YZ
CSHH G5P 0.38” x 3.00”
MOUNT, CABLE TIE HEAVY DUTY
QTY
1
5
2
5
10
2
10
1
2
1
1
1
2
1
2
1
3
6
1
1
1
3.5 FT
3 FT
2
1
1
1
1
2
7 FT
11.6 FT
1
2
1
1
11.5 FT
1
1
1
1
4
2
2
97
Parts - 1860 and 2460 Fertilizer Applicator
PRODUCT PUMP ASSEMBLY
1860 & 2460 Models
1
SEAL REPLACEMENT KIT
7
8
3
19
2
4
6
5
14
11
11
13
17
18
16
15
10
12
10
20
9
SXFMCSC200HYD R B
98
Parts - 1860 and 2460 Fertilizer Applicator
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PART NUMBER
DESCRIPTION
88663854
PRODUCT PUMP, ASSEMBLY
88661313
SEAL REPLACEMENT KIT
88661316
HYDRAULIC SEAL REPAIR KIT
88661314
VOLUTE, CAST IRON, 2”
88661315
VALOX IMPELLER 2”
THE FOLLOWING PARTS ARE FOR IDENTIFICATION PURPOSES ONLY
PIPE PLUG
PIPE PLUG, SS (OPTIONAL)
NUT, 3/8” NF
WASHER, 3/8” STAR, SS
MOUNTING FRAME
SCREW, 3/8” NC x 3/4”
SCREW, 3/8” NC x 3/4” SS (OPTIONAL)
SLINGER
SNAP RING, INTERNAL
BALL BEARNIG
SNAP RING, EXTERNAL
SPACER
KEY, 1/8” x 1/8” x 13/16”
SHAFT, EXTENDED KEYWAY, TANG, SS
SHAFT, 5/8” DIAMETER, KEYWAY, TANG SLOT, SS (OPTIONAL)
SEAL
COUPLING
MOTOR TO PUMP SCREW, 5/16” UNC x 3/4”
HYDRAULIC MOTOR
O-RING, SHAFT SEAL
QTY
1
1
1
1
1
4
1
1
1
4
1
2
2
2
1
1
1
1
1
4
1
1
99
Parts - 1860 and 2460 Fertilizer Applicator
FORWARD PRODUCT PUMP GROUP
1860 & 2460 Models
10
9
3
5
4
8
6
7
8
6
4
3
5
2
3
5
1
88664681 R A
ITEM
1
2
3
4
5
6
7
8
9
10
100
PART NUMBER
SXM200CPG45
SX063-0171-894
SXFC200BJ
SXM220200CPG
SX150G
SX200G
SX063-0171-066
SXTBC256
SXM200BRB
SXTBC256
DESCRIPTION
2” x 2” 45 FLG
VALVE, CONTROL, 1 1/2” POLY
CLAMP, 2” BANJO
COUPLER, 2” FP FLG, 2” FLG
GASKET, 2” FLANGED VALVE
GASKET, 2” COUPLING EPDM
RFM 100 FLOWMETER 2” IN & OUT
CLAMP, 2” SERIES WORM SCREW
HOSE BARB, 2” FLG x 2” HB
CLAMP, T-BOLT 2 11/32 - 25/8
QTY
1
1
3
2
3
2
1
2
1
1
Parts - 1860 and 2460 Fertilizer Applicator
QUICK FILL GROUP
1860 & 2460 Models
7
4
3
2
5
3
1
2
6
88664707 R -
ITEM
1
2
3
4
5
6
7
PART NUMBER
SX300CAP
SX300G
SXFC300BJ
SXM300BRB
SXM300CPG90
SXMVSF300
SXTBC350
DESCRIPTION
COUPLING, 3” CAM LEVER CAP
GASKET, 3” BANJO
CLAMP, 3” BANJO
HOSE BARB, 3” FLG x 3” HB, POLY
MANIFOLD ELBOW, 3” x 3” FLANGE 90
VALVE, 3” FLG x 3” M. ADAPT
CLAMP, T-BOLT 3 1/2 - 3 13/16”
QTY
1
2
2
1
1
1
2
101
Parts - 1860 and 2460 Fertilizer Applicator
TOOLBAR PLUMBING GROUP
Spray Monitors (1860 & 2460 Models)
3
2
1
5
4
9
6
7
8
B-0199
ITEM
1
2
3
4
5
6
7
8
9
102
PART NUMBER
88664836
88664835
88664838
88664834
88664837
SX6JM
SXLN-025-NIYZ
SXFW-025-YZ
SXBH0252005YZ
DESCRIPTION
ASSY, MONITOR, 4 COLUMN
ASSY, MONITOR, 5 COLUMN
ASSY, MONITOR, 6 COLUMN
ASSY, MONITOR, 7 COLUMN
ASSY, MONITOR, 8 COLUMN
CLAMP, 3/4” HOSE WORM SCREW
LOCKNUT, 1/4” NYLOCK INSERT
FLATWASHER, 1/4” ZINC PLATED
BOLT, 1/4” x 2” GR5
QTY
AS REQ.
AS REQ.
AS REQ.
AS REQ.
AS REQ.
AS REQ.
AS REQ.
AS REQ.
AS REQ.
Parts - 1860 and 2460 Fertilizer Applicator
TOOLBAR PLUMBING GROUP (CONT’D)
4
3
5
6
1
2
88663729
Spray Monitor Mount Assembly (Green Models)
ITEM
1
2
3
4
5
6
PART NUMBER
88663925
88663878
88665273
SXBH0311005YZ
88663733
SXNTFTL031188Y
DESCRIPTION
VALVE SECTION FRONT MOUNTING PLATE - GREEN
VALVE SECTION MOUNTING BRACKET - GREEN
BALL MOUNT GAUGE BRACKET - YELLOW
BOLT, 5/16” x 1” HEX BOLT
CSHH G5P 0.31” x 6.00”
NUT, FLG TP LCK 5/16-18 GR8 YZ
QTY
1
1
1
1
4
5
Spray Monitor Mount Assembly (Red Models)
ITEM
1
2
3
4
5
6
PART NUMBER
88663924
88663877
88665272
SXBH0311005YZ
88663733
SXNTFTL031188Y
DESCRIPTION
VALVE SECTION FRONT MOUNTING PLATE - RED
VALVE SECTION MOUNTING BRACKET - RED
BALL MOUNT GAUGE BRACKET - CREAM
BOLT, 5/16” x 1” HEX BOLT
CSHH G5P 0.31” x 6.00”
NUT, FLG TP LCK 5/16-18 GR8 YZ
QTY
1
1
1
1
4
5
103
Parts - 1860 and 2460 Fertilizer Applicator
TOOLBAR PLUMBING GROUP (CONT’D)
2
4
3
6
1
5
88663960
Spray Monitor Mount Assembly (Green Models)
ITEM
1
2
3
4
5
6
PART NUMBER
88665041
886633925
88663733
SXBH0311005YZ
88665273
SXNTFTL031188Y
DESCRIPTION
CENTER BALL VALVE MOUNT WELDMENT - GREEN
VALVE SECTION FRONT MOUNTING PLATE - GREEN
CSHH G5P 0.31” x 6.00”
NUT, FLG TP LCK 5/16-18 GR8 YZ
BALL MOUNT GAUGE BRACKET - YELLOW
BOLT, 5/16” x 1” HEX BOLT
QTY
1
1
1
1
4
5
Spray Monitor Mount Assembly (Red Models)
ITEM
1
2
3
4
5
6
104
PART NUMBER
88665040
88663924
88663733
SXNTFTL031188Y
88665272
SXBH0311005YZ
DESCRIPTION
CENTER BALL VALVE MOUNT WELDMENT - RED
VALVE SECTION FRONT MOUNTING PLATE - RED
CSHH G5P 0.31” x 6.00”
NUT, FLG TP LCK 5/16-18 GR8 YZ
BALL MOUNT GAUGE BRACKET - CREAM
BOLT, 5/16” x 1” HEX BOLT
QTY
1
1
1
1
4
5
Parts - 1860 and 2460 Fertilizer Applicator
TOOLBAR PLUMBING GROUP (CONT’D)
Injector & Knife Components
1
6
2
7
3
4
5
1
1
B-0198
ITEM
1
2
3
4
5
6
7
PART NUMBER
SX6JM
88665622
SXQJT8360-NYB
SX402910
SX3A1412G
88661128
88665767
DESCRIPTION
CLAMP, 3/4” HOSE WORM SCREW
HOSE BARB, 11/16” MPST x 1/2” HB 90
DIAPHRAGM, CHECK VALVE
CAP & GASKET, QT 1/4” THRD, BLK
HOSE FITTING, 1/4” MPT x 1/2” HB
HOSE BARB, 11/16” MPST x 1/2” HB
HOSE BARB, 1/2” HB x 1/2” HB
QTY
AS REQ.
AS REQ.
AS REQ.
AS REQ.
AS REQ.
AS REQ.
AS REQ.
105
Parts - 1860 and 2460 Fertilizer Applicator
COULTER BRACKET GROUP
1860 & 2460 Models
3
4
1
4
2
5
5
88665570 R
36 Row - 20” Spacing (60 Ft) 37 Coulters
ITEM
1
2
3
4
5
106
PART NUMBER
00012111
88663575
88663622
88665178
SXNTFTL062118Y
DESCRIPTION
CSHH G5P 0.62” x 2.00”
COULTER BRACKET, WELDMENT
U-BOLT, 0.63” x 5.13” x 8.63” LG
COULTER BRACKET, WELDMENT
NUT, 5/8-11 FLG, GR8
QTY
16
34
66
3
148
Parts - 1860 and 2460 Fertilizer Applicator
36 Row - 20” Spacing (60 Ft) 35 Coulters
ITEM
1
2
3
4
5
PART NUMBER
00012111
88663575
88663622
88665178
SXNTFTL062118Y
DESCRIPTION
CSHH G5P 0.62” x 2.00”
COULTER BRACKET, WELDMENT
U-BOLT, 0.63” x 5.13” x 8.63” LG
COULTER BRACKET, WELDMENT
NUT, 5/8-11 FLG, GR8
QTY
12
32
62
3
140
DESCRIPTION
CSHH G5P 0.62” x 2.00”
COULTER BRACKET, WELDMENT
U-BOLT, 0.63” x 5.13” x 8.63” LG
COULTER BRACKET, WELDMENT
NUT, 5/8-11 FLG, GR8
QTY
16
30
58
3
132
DESCRIPTION
CSHH G5P 0.62” x 2.00”
COULTER BRACKET, WELDMENT
U-BOLT, 0.63” x 5.13” x 8.63” LG
COULTER BRACKET, WELDMENT
NUT, 5/8-11 FLG, GR8
QTY
16
28
54
3
124
DESCRIPTION
CSHH G5P 0.62” x 2.00”
COULTER BRACKET, WELDMENT
U-BOLT, 0.63” x 5.13” x 8.63” LG
COULTER BRACKET, WELDMENT
NUT, 5/8-11 FLG, GR8
QTY
16
22
42
3
100
DESCRIPTION
CSHH G5P 0.62” x 2.00”
COULTER BRACKET, WELDMENT
U-BOLT, 0.63” x 5.13” x 8.63” LG
COULTER BRACKET, WELDMENT
NUT, 5/8-11 FLG, GR8
QTY
16
20
38
3
92
32 Row - 22” Spacing (60 Ft) 33 Coulters
ITEM
1
2
3
4
5
PART NUMBER
00012111
88663575
88663622
88665178
SXNTFTL062118Y
32 Row - 22” Spacing (60 Ft) 31 Coulters
ITEM
1
2
3
4
5
PART NUMBER
00012111
88663575
88663622
88665178
SXNTFTL062118Y
24 Row - 30” Spacing (60 Ft) 25 Coulters
ITEM
1
2
3
4
5
PART NUMBER
00012111
88663575
88663622
88665178
SXNTFTL062118Y
24 Row - 30” Spacing (60 Ft) 23 Coulters
ITEM
1
2
3
4
5
PART NUMBER
00012111
88663575
88663622
88665178
SXNTFTL062118Y
107
Parts - 1860 and 2460 Fertilizer Applicator
COULTER W / KNIFE GROUP
1860 & 2460 Models
4
3
6
1
2
5
88665558 R -
36 Row - 20” Spacing (60 Ft) 37 Coulters
ITEM
PART NUMBER
DESCRIPTION
QTY
1
2
3
4
5
6
00087972
88663897
88664852
88664853
88664856
SXNTFTL050138Y
CSHH G5 P 0.50” x 2.50” 86505344
CSHH G5P 0.50” x 3.00”
MOUNT, CABLE TIE HD 1/2”
LOCKNUT, 1/2” CENTERLOCK YZ
COULTER KNIFE MODIFIED, ASSEMBLY
NUT FLG, TP LCK, 1/2”-13
74
74
37
37
37
148
108
Parts - 1860 and 2460 Fertilizer Applicator
36 Row - 20” Spacing (60 Ft) 35 Coulters
ITEM
PART NUMBER
DESCRIPTION
QTY
1
2
3
4
5
6
00087972
88663897
88664852
88664853
88664856
SXNTFTL050138Y
CSHH G5 P 0.50” x 2.50” 86505344
CSHH G5P 0.50” x 3.00”
MOUNT, CABLE TIE HD 1/2”
LOCKNUT, 1/2” CENTERLOCK YZ
COULTER KNIFE MODIFIED, ASSEMBLY
NUT FLG, TP LCK, 1/2”-13
70
70
35
35
35
140
32 Row - 22” Spacing (60 Ft) 33 Coulters
ITEM
PART NUMBER
DESCRIPTION
QTY
1
2
3
4
5
6
00087972
88663897
88664852
88664853
88664856
SXNTFTL050138Y
CSHH G5 P 0.50” x 2.50” 86505344
CSHH G5P 0.50” x 3.00”
MOUNT, CABLE TIE HD 1/2”
LOCKNUT, 1/2” CENTERLOCK YZ
COULTER KNIFE MODIFIED, ASSEMBLY
NUT FLG, TP LCK, 1/2”-13
66
66
33
33
33
132
32 Row - 22” Spacing (60 Ft) 31 Coulters
ITEM
PART NUMBER
DESCRIPTION
QTY
1
2
3
4
5
6
00087972
88663897
88664852
88664853
88664856
SXNTFTL050138Y
CSHH G5 P 0.50” x 2.50” 86505344
CSHH G5P 0.50” x 3.00”
MOUNT, CABLE TIE HD 1/2”
LOCKNUT, 1/2” CENTERLOCK YZ
COULTER KNIFE MODIFIED, ASSEMBLY
NUT FLG, TP LCK, 1/2”-13
62
62
31
31
31
124
24 Row - 30” Spacing (60 Ft) 25 Coulters
ITEM
PART NUMBER
DESCRIPTION
QTY
1
2
3
4
5
6
00087972
88663897
88664852
88664853
88664856
SXNTFTL050138Y
CSHH G5 P 0.50” x 2.50” 86505344
CSHH G5P 0.50” x 3.00”
MOUNT, CABLE TIE HD 1/2”
LOCKNUT, 1/2” CENTERLOCK YZ
COULTER KNIFE MODIFIED, ASSEMBLY
NUT FLG, TP LCK, 1/2”-13
50
50
25
25
25
100
24 Row - 30” Spacing (60 Ft) 23 Coulters
ITEM
PART NUMBER
DESCRIPTION
QTY
1
2
3
4
5
6
00087972
88663897
88664852
88664853
88664856
SXNTFTL050138Y
CSHH G5 P 0.50” x 2.50” 86505344
CSHH G5P 0.50” x 3.00”
MOUNT, CABLE TIE HD 1/2”
LOCKNUT, 1/2” CENTERLOCK YZ
COULTER KNIFE MODIFIED, ASSEMBLY
NUT FLG, TP LCK, 1/2”-13
46
46
23
23
23
92
109
Parts - 1860 and 2460 Fertilizer Applicator
COULTER W / INJECT GROUP
1860 & 2460 Models
4
3
6
1
2
5
88665560 R -
36 Row - 20” Spacing (60 Ft) 37 Coulters
ITEM
1
2
3
4
5
6
110
PART NUMBER
00087972
88663897
88664852
88664853
88664855
SXNTFTL050138Y
DESCRIPTION
CSHH G5 P 0.50” x 2.50” 86505344
CSHH G5P 0.50” x 3.00”
MOUNT, CABLE TIE HD 1/2”
LOCKNUT, 1/2” CENTERLOCK YZ
COULTER INJECTOR MODIFIED, ASSEMBLY
NUT FLG, TP LCK, 1/2”-13
QTY
74
74
37
37
37
148
Parts - 1860 and 2460 Fertilizer Applicator
36 Row - 20” Spacing (60 Ft) 35 Coulters
ITEM
PART NUMBER
DESCRIPTION
QTY
1
2
3
4
5
6
00087972
88663897
88664852
88664853
88664855
SXNTFTL050138Y
CSHH G5 P 0.50” x 2.50” 86505344
CSHH G5P 0.50” x 3.00”
MOUNT, CABLE TIE HD 1/2”
LOCKNUT, 1/2” CENTERLOCK YZ
NUT, FLG TP LCK, 1/2”-13
70
70
35
35
35
140
COULTER INJECTOR MODIFIED, ASSEMBLY
32 Row - 22” Spacing (60 Ft) 33 Coulters
ITEM
PART NUMBER
DESCRIPTION
QTY
1
2
3
4
5
6
00087972
88663897
88664852
88664853
88664855
SXNTFTL050138Y
CSHH G5 P 0.50” x 2.50” 86505344
CSHH G5P 0.50” x 3.00”
MOUNT, CABLE TIE HD 1/2”
LOCKNUT, 1/2” CENTERLOCK YZ
NUT FLG, TP LCK, 1/2”-13
66
66
33
33
33
132
COULTER INJECTOR MODIFIED, ASSEMBLY
32 Row - 22” Spacing (60 Ft) 31 Coulters
ITEM
PART NUMBER
DESCRIPTION
QTY
1
2
3
4
5
6
00087972
88663897
88664852
88664853
88664855
SXNTFTL050138Y
CSHH G5 P 0.50” x 2.50” 86505344
CSHH G5P 0.50” x 3.00”
MOUNT, CABLE TIE HD 1/2”
LOCKNUT, 1/2” CENTERLOCK YZ
NUT FLG, TP LCK, 1/2”-13
62
62
31
31
31
124
COULTER INJECTOR MODIFIED, ASSEMBLY
24 Row - 30” Spacing (60 Ft) 25 Coulters
ITEM
PART NUMBER
DESCRIPTION
QTY
1
2
3
4
5
6
00087972
88663897
88664852
88664853
88664855
SXNTFTL050138Y
CSHH G5 P 0.50” x 2.50” 86505344
CSHH G5P 0.50” x 3.00”
MOUNT, CABLE TIE HD 1/2”
LOCKNUT, 1/2” CENTERLOCK YZ
NUT FLG, TP LCK, 1/2”-13
50
50
25
25
25
100
COULTER INJECTOR MODIFIED, ASSEMBLY
24 Row - 30” Spacing (60 Ft) 23 Coulters
ITEM
PART NUMBER
DESCRIPTION
QTY
1
2
3
4
5
6
00087972
88663897
88664852
88664853
88664855
SXNTFTL050138Y
CSHH G5 P 0.50” x 2.50” 86505344
CSHH G5P 0.50” x 3.00”
MOUNT, CABLE TIE HD 1/2”
LOCKNUT, 1/2” CENTERLOCK YZ
46
46
23
23
23
92
COULTER INJECTOR MODIFIED, ASSEMBLY
NUT FLG, TP LCK, 1/2”-13
111
Parts - 1860 and 2460 Fertilizer Applicator
COULTER ASSEMBLY (STRAIGHT)
RH W / Knife
47
48
46
1
45
7
2
44
3
42
9
5
4
43
41
40
8 10
6
39
38
13
11
14
12
22
15
36
37
24
35
16
26
33
17
21
18
19
34
23
20
31
28
15
25
30
27
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
112
PART NUMBER
SX2570-375
88664879
88664880
88664881
88664882
SX2571-076
88664883
SX2550-027
88664884
SX2550-029
88664885
88664886
88664887
32
DESCRIPTION
HUB CAP
1/8” x 1 1/4” COTTER PIN, BLACK
5/8”-18 SLOTTED HEX NUT BLK
1/2” MED LOCKWASHER ZP
1/2”-13 HEX NUT ZP
RIPPLE BLADE 20”
5/8” FLATWASHER, 1/4” +/- 0.010 THICK
CONE, LM67048
HUB PRESSED ASSY
CUP (PRE-ASSY W/9) LM67010
TRIPLE LIP SEAL, NTI #1812-4
1/2”-13 x 1 1/4” CAR BOLT GR5 ZP
1/2”-13 LOCK HEX NUT ZP
29
88661366 R B
QTY
1
1
4
4
4
1
1
2
1
2
1
4
1
Parts - 1860 and 2460 Fertilizer Applicator
ITEM
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
PART NUMBER
88664888
88664889
88664890
SXFW-075-SAE-YZ
88664891
88664892
SX2975-303
88664893
88664894
88664895
88664896
88664897
88664898
88664899
88664900
SX2995-110
88664901
88664902
88664903
SX2550-795
88664904
88664905
88664906
88664907
88664908
88664909
88664910
88664911
SX2996-205
88664912
88664913
88664914
SX2995-309
SX2996-200
88664915
88664916
88664920
88664918
88664919
88661373
88664917
DESCRIPTION
1/2” ID x 1 1/2” OD x 10 GA MA BU ZP
PIVOT SLEEVE
3/4”-10 LOCK HEX NUT ZP
3/4” STANDARD FLATWASHER ZP
PIVOT SLEEVE
5/8”-11 x 1” SQ. HCPSS GR5 ZP
LOCKING COLLAR, 2975
1/4”-28 ZERK STRAIGHT SELF-TAP
COULTER PIVOT, RH (SHOWN)
COULTER PIVOT, LH
UPPER COULTER ARM ASSY
1” ID x 1 1/4” OD x 1/2” BRNZ BUSH
1/2”-13 x 4” HSFHCS
5/8”-11 WHIZLOCK HEX NUT ZP
SPRING ROD, 13 1/2”
LOWER COULTER ARM ASSY
ARM BRNZ BUSHING, 2995
3/4”-10 x 6” HHCS G5 ZP
5/8” x 1 3/4” SLIC PIN YYD
SPRING, 0.562 WIRE x 11” LONG
SPRING BUSHING PAINTED, 2975
5/8”-11 x 2 1/2” HHCS GR5 ZP
21/32” ID x 2 1/4” OD x 1/4” MA BU
LOWER ARM PIVOT
5/8”-18 x 1 1/2” HHCS GR5 ZP
5/8” MED LOCKWASHER ZP
UPPER ARM PIVOT/WASHER ZP
1/2”-13 HEX NIF, LOCK NUT ZP
RH KNIFE ARM/SPINDLE WA, 2996
LH KNIFE ARM/SPINDLE WA, 2996
KNIFE SHIM 16 GA ZP
KNIFE SHIM, 1/8” ZP
SPACER BLOCK, 1.531”
LIQUID FERTILIZER KNIFE WA, 20”
1/2” FLAT WASHER, HARDENED PC
1/2”-13 x 3 1/2” HHCS GR8 ZDP
HUB CAP RETAINER
ROLL PIN FOR SHANK
COTTER PIN FOR SHANK
SHANK, 1 1/2” x 27-1/8
CRITICAL ADJUSTMENT DECAL (NOT SHOWN)
QTY
1
1
2
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
2
1
1
1
1
1
113
Parts - 1860 and 2460 Fertilizer Applicator
COULTER ASSEMBLY (STRAIGHT) (CONT’D)
RH W / Injector
8
15
9
12
13
5
13
12
2
7
14
10
4
6
13
1
16
11
18
19
3
21
22
23
20
17
12
13
88661368 R B-1
114
Parts - 1860 and 2460 Fertilizer Applicator
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
PART NUMBER
00012008
00012071
88664913
88664914
88664922
SX2995-320
SX2995-301
88664919
88664917
88664892
88664886
88664882
88664881
88664923
88661373
SX2975-303
88661371
SX2995-131
88664924
88664925
88664926
88664927
88664920
DESCRIPTION
1/2”-13 x 1 1/2” HHCS GR5 ZP
1/2”-13 x 1” HHCS GR5 ZP
KNIFE SHIM, 16 GA. ZP
KNIFE SHIM, 1/8” ZP
ADJUSTMENT PLATE, INJECTOR
SPACER, INJECTOR
INJECTOR MOUNT PLATE
5/16” x 2-1/2” COTTER PIN ZP
3/8” x 2-1/2” ROLL PIN ZP
5/8”-11 x 1” SQ HCPSS GR5 ZP
1/2”-13 x 1 1/4” CAR BOLT GR5
1/2”-13 HEX NUT ZP
1/2” MED LOCKWASHER ZP
GEN III COULTER ARM ASSY (W/INJECT)
SHANK, 1 1/2” x 27-1/8
2975 LOCKING COLLAR
.157” x 20" RIPPLE BLADE
SPRING INJECTOR ASSEMBLY
3" NIPPLE, 1/4 NPT SS
INJECTOR ROD W A 1/2”-13
1/2”-13 x 2” CAR BOLT GR5 ZP
1/2”-13 JAM HEX NUT ZP
HUB CAP RETAINER
QTY
2
2
1
2
2
1
1
1
1
1
4
8
9
1
1
1
1
1
1
1
2
1
1
115
Parts - 1860 and 2460 Fertilizer Applicator
COULTER ARM ASSEMBLY
RH W / Injector
1
2
3
5
8
4
7
12
6
10
11
13
17
14
9
13
15
12
16
88661368 R B-2
116
Parts - 1860 and 2460 Fertilizer Applicator
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PART NUMBER
88664927
88664904
SX2550-795
88664928
88664929
88664895
88664930
88664931
88664900
88664879
88664903
88664932
88664933
88664884
88664893
SX2550-029
88664934
SX2550-027
88664883
88664880
SX2570-375
88664885
DESCRIPTION
3/4”-10 NYLON INSERT LOCKNUT ZP
2975 SPRING BUSHING PAINTED
SPRING, 0.562” WIRE x 11” LONG
10” POLY HELPER SPRING
COULTER PIVOT, RH (SHOWN)
COULTER PIVOT, LH
1/4” x 1 3/4” COTTER PIN ZYD
1 17/64” ID x 1 7/8” OD x 14GA MB
SPRING ROD, 13-1/2”
1/8” x 1 1/4” COTTER PIN BLACK
5/8” x 1 3/4” SLIC PIN ZYD
GEN III W / KNIFE ARM WA RH (SHOWN)
GEN III W / KNIFE ARM WA LH
HUB PRESSED ASSEMBLY
1/4”-28 ZERK STRAIGHT SELF-TAP
CUP, LM67010
PLOW COULTER HUB CASTING
CONE, LM67048
5/8” FLATWASHER, 1/4” +/- 0.010 THICK
5/8”-18 SLOTTED HEX NUT, BLACK
HUB CAP, WILTON #909902
TRIPLE LIP SEAL, NTI #1812-4
QTY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
117
Parts - 1860 and 2460 Fertilizer Applicator
COULTER MOUNTING ASSEMBLY
RH W / Injector & RH W / Knife
2
5
2
3
4
1
88661368 R B-3
ITEM
1
2
3
4
5
118
PART NUMBER
88664921
SX2990-314
SX2990-360
88664892
88664887
DESCRIPTION
1/2”-13 x 7 HHCS GR5 ZP
CLAMP PLATE 4” SQ & 3” DIAMOND
CLAMP CASTING, DRILLED
5/8”-11 x 1” SQ. HCPSS GR5 ZP
1/2”-13 HEX LOCKNUT ZP
QTY
4
2
2
2
4
Parts - 1860 and 2460 Fertilizer Applicator
GAUGE WHEEL GROUP LH
1860 & 2460 Models
5
7
6
4
3
1
2
88663774 R -
ITEM
1
2
3
4
5
6
7
PART NUMBER
SX014123
SX011506B
SXPHI-100-525
88663950
88663771
88663952
SXFW-075-SAE-YZ
DESCRIPTION
TUBE, SPINDLE WELDMENT
TIRE & WHEEL ASSY, 7.6-15SL
PIN, HITCH, 1” x 5 1/4”
GAUGE WHEEL WELDMENT
GAUGE WHEEL SUBWELDMENT
NUT FLG, TP LCK, 3/4”-10 GR5YZ
FLATWASHER, 3/4” YZ
QTY
1
1
1
1
1
2
1
119
Parts - 1860 and 2460 Fertilizer Applicator
GAUGE WHEEL GROUP RH
1860 & 2460 Models
5
7
6
4
3
1
2
88663707 R -
ITEM
1
2
3
4
5
6
7
120
PART NUMBER
SX014123
SX011506B
SXPHI-100-525
88663950
88663771
88663952
SXFW-075-SAE-YZ
DESCRIPTION
TUBE, SPINDLE WELDMENT
TIRE & WHEEL ASSY, 7.6-15SL
PIN, HITCH, 1” x 5 1/4”
GAUGE WHEEL WELDMENT
GAUGE WHEEL SUBWELDMENT
NUT FLG, TP LCK, 3/4”-10 GR5YZ
FLATWASHER, 3/4” YZ
QTY
1
1
1
1
1
2
1
Parts - 1860 and 2460 Fertilizer Applicator
GAUGE WHEEL HUB
1860 & 2460 Models
6
1
9
8
3
5
2
7
4
SX011503 R
ITEM
1
2
3
4
5
6
7
8
9
PART NUMBER
88665707
88665708
88665709
88665710
88665711
88665712
88665713
88665714
88665715
DESCRIPTION
HUB W/CUPS
OUTER CUP
OUTER CONE
INNER CUP
INNER CONE
STUD
CAP, HUB
GREASE SEAL
NUT
QTY
1
1
1
1
1
6
1
1
6
121
Parts - 1860 and 2460 Fertilizer Applicator
TIRE / WHEEL SINGLE 380 / 90 R54
Cream
NOTE:
Tighten to 420 Foot Pounds of torque, Do Not Lubricate.
2
1
Direction of rotation.
5
3
4
88663710 R A
ITEM
1
2
3
4
5
122
PART NUMBER
88663740
88663739
88663734
88663735
88663863
DESCRIPTION
TIRE 380/90 R54 LHI RHO, ASSEMBLY
TIRE 380/90 R54 LHO RHI, ASSEMBLY
CSFL G8 P 0.75” x 2.50” NF YZ
NUT, FLG TP LCK 3/4”-16 GR8 YZ
HUB SPACER 30 INCH SINGLE, WELDMENT
QTY
1
1
24
24
2
Parts - 1860 and 2460 Fertilizer Applicator
TIRE / WHEEL SINGLE 380 / 90 R54
Yellow
NOTE:
Tighten to 420 Foot Pounds of torque, Do Not Lubricate.
1
2
5
3, 4
3, 4
88664636 R A
ITEM
1
2
3
4
5
PART NUMBER
88663870
88663869
88663734
88663735
88663864
DESCRIPTION
TIRE 380/90 R54 LHI RHO, ASSEMBLY
TIRE 380/90 R54 LHO RHI, ASSEMBLY
CSFL G8 P 0.75” x 2.50” NF YZ
NUT, FLG TP LCK 3/4”-16 GR8 YZ
HUB SPACER 30 INCH SINGLE, WELDMENT
QTY
1
1
24
24
2
123
Parts - 1860 and 2460 Fertilizer Applicator
TIRE / WHEEL STRADDLE DUAL 320 / 90 R54
20” Spacing
NOTE:
Tighten to 420 Foot Pounds of torque, Do Not Lubricate.
1
2
5
1
2
Direction of rotation.
3, 4
88663712 R A
ITEM
1
2
3
4
5
124
PART NUMBER
88663743
88663744
88663734
88663735
88663866
DESCRIPTION
TIRE 320/90 R54 LHO RHI, ASSEMBLY
TIRE 320/90 R54 LHI RHO, ASSEMBLY
CSFL G8 P 0.75” x 2.50” NF YZ
NUT, FLG TP LCK 3/4”-16 GR8 YZ
HUB SPACER 20 INCH, WELDMENT
QTY
2
2
48
48
2
Parts - 1860 and 2460 Fertilizer Applicator
TIRE / WHEEL STRADDLE DUAL 320 / 90 R54
20” Spacing
NOTE:
Tighten to 420 Foot Pounds of torque, Do Not Lubricate.
2
1
5
2
1
3, 4
3, 4
88664637 R A
ITEM
1
2
3
4
5
PART NUMBER
88663873
88663874
88663734
88663735
88663865
DESCRIPTION
TIRE 320/90 R54 LHO RHI, ASSEMBLY
TIRE 320/90 R54 LHI RHO, ASSEMBLY
CSFL G8 P 0.75” x 2.50” NF YZ
NUT, FLG TP LCK 3/4”-16 GR8 YZ
HUB SPACER 20 INCH, WELDMENT
QTY
2
2
48
48
2
125
Parts - 1860 and 2460 Fertilizer Applicator
HUB ASSEMBLY
1860 & 2460 Models
5
14
12
1
2
6
7
8
9
11
10
7
4
3
13
6
88660676B
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
126
PART NUMBER
88660662
88660661
88660663
88660664
88660665
88660666
88660667
88660668
88660669
88660670
88661532
88666341
88666342
88661542
DESCRIPTION
HUB, 10 BOLT, 13.19” BC
FITTING GREASE
BOLT, HUBCAP
SEAL, GREASE
STUD, WHEEL
WASHER
NUT, CASTLE
INNER CONE
GASKET
CAP, HUB
OUTER CONE
INNER CUP
OUTER CUP
SPINDLE, ASSEMBLY
QTY
1
1
4
1
10
1
1
1
1
1
1
1
1
1
Parts - 1860 and 2460 Fertilizer Applicator
RAVEN 450
1860 & 2460 Models
1
2
3
88664957 R -
ITEM
1
2
3
PART NUMBER
SX063-0171-220
SX115-0171-085
88664958
DESCRIPTION
CONSOLE ASSY, 450 W/SERIAL PORT
CABLE, RAVEN 450 CONTROL CABLE
CABLE, FLOW CONTROL 43 FT 6 SECT
QTY
1
1
1
127
Parts - 1860 and 2460 Fertilizer Applicator
LIGHTING MARKING GROUP
1860 & 2460 Models
2
7
3
4
11
9
8
1
6
10
11
5
5
5
5
5
5
88663796-2
128
Parts - 1860 and 2460 Fertilizer Applicator
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
PART NUMBER
88664979
SX004560
SX004561
SX013588
SX17-5910
SX17-5915
SX17-5920
SXBH0250758YZ
SXBH-025-100-5-YZ
SXFW-025-YZ
SXJD5403
SXLN-025-NIYZ
SXFW-050-YZ
DESCRIPTION
BRACKET SMV
LAMP, TURN/TAIL
LAMP, FLASH/WARN TAIL, AMBER
MOUNT, SMV
DECAL, REFLECT AMBER, 2” x 9”
DECAL, REFLECT RED, 2” x 9”
DECAL, DAY ORANGE, 2” x 9”
BOLT, 1/4” x 3/4” GR 8
BOLT, 1/4” x 1” GR 5
FLATWASHER, 1/4” ZINC PLATED
SIGN, SMV
LOCKNUT, 1/4” NYLOCK INSERT
FLATWASHER, 1/2”
QTY
1
2
2
1
8
2
2
4
2
2
1
6
2
129
Parts - 1860 and 2460 Fertilizer Applicator
HITCH GROUP
1860 & 2460 Models
11
14
13
17,18
15,16
17,18
10
19
12
7
3, 4
9
5
8
15,16
6
2
2, 3, 4
1
88663747 R A
130
Parts - 1860 and 2460 Fertilizer Applicator
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
PART NUMBER
88661392
09602223
SXLN-100-NI-YZ
SXFW-100-SAE-YZ
88660499
88663962
SX014115
SX014125
SXHPC210
88664972
88664974
SX006069
SX013049
88660521
SXBH0381005YZ
SXLN-038-NIYZ
SXBH-025-075-8YZ
SXLN-025-NIYZ
SX64J
DESCRIPTION
HITCH, PINTLE, CAT. 4-5 CROSSOVER
CSHH G5 P 1” x 7”
LOCKNUT, 1” NYLON INSERT
WASHER, 1” SAE FLAT, YZ
CHAIN, AG SAFETY, 41,000 LB
TUBE - SAFETY CHAIN
TOP HANDLE JACK, WELDMENT
PIN, JACK
PIN CLIP, 1/8” x 23/16”
CHANNEL FORMED
RACK, HYD HOSE
MOUNT, STRAINER FLANGED
MANUAL STORAGE TUBE
HOLDER, ELECTRICAL PLUG
BOLT, 3/8” x 1” YZ
LOCKNUT, 3/8” NYLON INSERT YZ
BOLT, 1/4” x 3/4” GR 8
LOCKNUT, 1/4” NYLOCK INSERT
CLAMP, HOSE, 4” WORM SCREW
QTY
1
4
4
8
1
1
1
1
1
1
1
1
1
1
4
4
4
4
2
131
Parts - 1860 and 2460 Fertilizer Applicator
OUTER WING CYLINDER
1860 & 2460 Models
6
5
3
4
4
2
2
1
88663773 R C
ITEM
1
2
3
4
5
6
132
PART NUMBER
88663501
09617891
88663800
88664827
88664828
SX6400-6-8
DESCRIPTION
OUTER WING LIFT CYLINDER
90° ELBOW, 37D - OR x 8-10 86512105
FLOW REGULATOR VALVE, P.C.
90° ADAPTER, 08 MJIC x 06 ORB
STRAIGHT ADAPTER, 08 FJX x 08 ORB
MALE ADAPTER, 3/8” JIC x 3/4” ORB
QTY
1
2
1
2
1
1
Parts - 1860 and 2460 Fertilizer Applicator
INNER FOLD CYLINDER
1860 & 2460 Models
4
2
6
8
7
3
5
9
1
2
8
3
2
88663757 R B
ITEM
1
2
3
4
5
6
7
8
9
PART NUMBER
88663500
88663680
SXBH0381005YZ
88663669
88664827
09617891
SX6801-6
SXFW-038YZ
164910
DESCRIPTION
INNER WING LIFT CYLINDER
FLAG BUSHING
BOLT, 3/8” x 1” YELLOW ZINC
FLAG AND PIN WELDMENT
90° ADAPTER, 08 MJIC x 06 ORB
90° ELBOW, 37D-OR 8-10 (86512105)
90° ADAPTER ELBOW, 06 MJIC x 06 ORB
FLATWASHER, 3/8” GRADE 5
90° ELBOW, 7/8” MJIC x 7/8” ORB
QTY
1
2
2
2
1
1
1
2
1
133
Parts - 1860 and 2460 Fertilizer Applicator
MAIN LIFT CYLINDER (LH)
1860 & 2460 Models
2
7
8
1
3
6
5
3
6
4
8
88663752 R A
ITEM
1
2
3
4
5
6
7
8
134
PART NUMBER
88663502
88663669
88663680
88663777
88664811
SXBH0381005YZ
86507102
SXFW-038YZ
DESCRIPTION
LH MAIN LIFT CYLINDER
FLAG AND PIN WELDMENT
FLAG BUSHING
MAIN LIFT FLAG AND PIN WELDMENT
90° ADAPTER, 10 MJIC x 12 ORB
BOLT, 3/8” x 1” YELLOW ZINC
STRAIGHT ADAPTER, 12 MORB x 10 MJIC
FLATWASHER, 3/8” GRADE 5
QTY
1
1
2
1
1
2
1
2
Parts - 1860 and 2460 Fertilizer Applicator
MAIN LIFT CYLINDER (RH)
1860 & 2460 Models
2
7
8
1
3
5
6
3
6
4
8
88663753 R A
ITEM
1
2
3
4
5
6
7
8
PART NUMBER
88663502
88663669
88663680
88663777
88664811
SXBH0381005YZ
86507102
SXFW-038YZ
DESCRIPTION
LH MAIN LIFT CYLINDER
FLAG AND PIN WELDMENT
FLAG BUSHING
MAIN LIFT FLAG AND PIN WELDMENT
90° ADAPTER, 10 MJIC x 12 ORB
BOLT, 3/8” x 1” YELLOW ZINC
STRAIGHT ADAPTER, 12 MORB x 10 MJIC
FLATWASHER, 3/8” GRADE 5
QTY
1
1
2
1
1
2
1
2
135
Parts - 1860 and 2460 Fertilizer Applicator
CONTROL VALVE
1860 & 2460 Models
16
11
5
17
9
3
7
11
13
8
6
9
10
2
18
12
4
14
15
1
2
13
3
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
136
PART NUMBER
88664769
88663807
88663808
88663951
88664758
88664759
88664760
88665156
88665157
88665158
88665155
SX6400-6-8
SX6400-8
SX016832
SX6602-8
88664767
88664766
88664768
88663768 R B
DESCRIPTION
TOOLBAR CONTROL VALVE BLOCK
ADAPTER, 10 MJIC x 8 MORB
ADAPTER, 10 MJIC x 10 MORB
TEE, 10 MJIC x 10 MJIC x 10 FJX
FLOW REGULATOR, W/BODY
STRAIGHT ADAPTER, 12 ORB x 10 FJIC
90° ELBOW ADAPTER, 12 ORB x 10 MJIC
TEE, 10 MJ x10 MJ x 10 FJ
FEMALE SWIVEL, 4 MORB x 1/4 NPT
90° ELBOW, 10 MORB x 10 MJIC
GAUGE, 3000 PSI, GLYCERINE FILLED
MALE ADAPTER, 3/8 JIC x 3/4 ORB
STRAIGHT ADAPTER, 08 MJIC x 08 ORB
STRAIGHT ADAPTER, 10 ORB x 08 MJIC
TEE ADAPTER, 08 MJIC x 08 FJX x 08 MJIC
PRESSURE REDUCER / RELIEF, #10
FLOW DIVIDER / COMBINER, #12
CHECK VALVE, SEQ W / REV CHCK
QTY
1
2
5
1
1
1
1
1
2
1
2
2
8
1
1
2
1
4
Specifications - 1860 and 2460 Fertilizer Applicator
SPECIFICATIONS
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
HYDRAULIC DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
HARDWARE TORQUE VALUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Metric Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Imperial Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
HYDRAULIC CONNECTION SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
O-Ring Fitting (Straight Thread) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
O-ring Face Seal Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Flare Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Port Seal (O-ring Boss) Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Tubelines And Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
NOZZLE SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Density Correction Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
NOZZLE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
137
Specifications - 1860 and 2460 Fertilizer Applicator
138
Specifications - 1860 and 2460 Fertilizer Applicator
SPECIFICATIONS
Dimensions
Overall Field Dimensions
A
B
B-0202
DESCRIPTION
1860
2460
Overall Field Height (A)
9 ft. 3 in.
9 ft. 3 in.
Overall Field Width (B)
60 ft. 9 in.
60 ft. 9 in.
Transport Width
18 ft. 6 in.
18 ft. 6 in.
Transport Height
13 ft. 6 in.
13 ft. 6 in.
Transport Length
24 ft. 3 in.
24 ft. 3 in.
185 in.
185 in.
Pin To Axle
NOTE: Dimensions are approximate measurements.
Performance
DESCRIPTION
Spray Tank
Fresh Water Safety Tank
Plumbing
1860
2460
1800 U.S. gal.
2400 U.S. gal.
9 U.S. gal.
9 U.S. gal.
Ace Hydraulic Driven Centrifugal Pump Kit • 5 Section Control Valves
Raven 450 or Envisio Pro Rate Controller
Toolbar
Available in 24/30 in. (25), 32/22 in. (33), 36/20 in. (37) widths
Coulters
20 in. Ripple, Spring - Cushioned (Knives or Injectors)
Gauge Wheels
Tires
Wheel Spacing
Ground Clearance
Electrical Harness
4
4
Dual Tire 380 / 90R54
Single Tire / Rim 380 / 90R54
Single Tire / Rim 480 / 80R42
Dual Tire 380 / 90R54
60 in. / 120 in., 80 in. / 120 in., 88 in. / 132 in. Duals
36 in. in field operation, 54 in. on turn rows
7 - Pin
7 - Pin
139
Specifications - 1860 and 2460 Fertilizer Applicator
HYDRAULIC DIAGRAM
24
5
38
ROD SIDE
BASE SIDE
10
11
PORT #1
PORT #2
29
25
7
11
18
27
PORT #1
25
12
PORT #2
26
6
B2
BASE SIDE
ROR
14
17
ROB
16
RIR
15
2
ROD SIDE
12
DPO
20
BASE SIDE
PORT #1
PORT #2
MLB
22
15
17
16
ROD SIDE
6
88664758
HYD FLOW
REGULATOR
DPI
GDPI
LIB
19
BASE SIDE
DPR
DPI
13
PRODUCT PUMP
MLR
21
21
1
8
RIB
GDPO
DPO
19
31
9
A2
3
ROD
SIDE
9
23
10
A1
28
31
9
B1
LIR
LOB
LOR
3
27
26
PORT #2
PORT #1
VALVE PORT
30
29
PORT #2
12
11
11
PORT #1
BASE SIDE
ROD SIDE
5
88664754
140
Specifications - 1860 and 2460 Fertilizer Applicator
ITEM
PART NUMBER
DESCRIPTION
QTY
1
88663752
LH MAIN LIFT CYLINDER
1
2
88663753
RH MAIN LIFT CYLINDER
1
3
88663757
INNER WING FOLD CYLINDER
2
4
88663768
HYDRAULIC VALVE (Not Shown)
1
5
88663773
OUTER WING FOLD CYLINDER
2
6
88664930
HYDRAULIC BALL VALVE, COATED - 06
2
7
88664931
HYDRAULIC BALL VALVE, COATED - 12
1
8
88663840
INCLUDED IN PUMP ASSEMBLY
-
9
88665182
HYDRAULIC HOSE - #10 x 180” LG EL
3
10
88665065
HYDRAULIC HOSE - #10 x 77” LG 45
1
11
88665072
HYDRAULIC HOSE - #8 x 231” LG
4
12
88665073
HYDRAULIC HOSE - #8 x 235” LG
2
13
88665074
HYDRAULIC HOSE - #8 x 140” LG
1
14
88665075
HYDRAULIC HOSE - #8 x 48” LG EL
2
15
88665076
HYDRAULIC HOSE - #8 x 140” LG EL
1
16
88665077
HYDRAULIC HOSE - #8 x 133” LG
2
17
88665078
HYDRAULIC HOSE - #6 x 137” LG
2
18
88665079
HYDRAULIC HOSE - #6 x 119” LG EL
2
19
88665080
HYDRAULIC HOSE - #10 x 151” LG
2
20
88665081
HYDRAULIC HOSE - #10 x 58” LG 45
1
21
88665082
HYDRAULIC HOSE - #10 x 43” LG EL
2
22
88665083
HYDRAULIC HOSE - #10 x 51” LG 45
1
23
88665084
HYDRAULIC HOSE - #10 x 103” LG EL
1
24
88663859
HYDRAULIC QUICK DISCONNECT - CNCTR
6
25
86507102
HYDRAULIC CONNECTOR - SHORT
2
26
88665147
HYDRAULIC ADAPTER, STRAIGHT - 6 MORB - 8 FJX
2
27
88665148
HYDRAULIC ADAPTER, TEE - 8 MORB - 8 MJ - 8 MJ
2
28
88665151
HYDRAULIC ADAPTER, 8 FJIC - 6 MJIC
2
29
88665160
HYDRAULIC ADAPTER, STRAIGHT - 8 MORB - 8 MJIC
2
30
88663800
FLOW VALVE, REG. P.C.
2
31
86509028
HYDRAULIC ADAPTER, REDUCER
2
32
SXBH0252005YZ
BOLT, 1/4” x 2” BOLT GRADE 5
4
33
SXBH0252505YZ
BOLT, 1/4” x 2 1/2” HEX GRADE 5
4
34
SXBH0253008YZ
BOLT, 1/4” x 3” GRADE 8, YELLOW ZINC
2
35
SXFW-025-YZ
FLATWASHER, 1/4” YELLOW ZINC
14
36
SXLN-025-NIYZ
LOCKNUT, 1/4” NYLON INSERT
10
37
88665271
SLEEVE, SUBURBAN SIDEWINDER SL4.0
2
38
88663808
HYDRAULIC ADAPTER, 10 MJIC - 10 MORB
3
141
Specifications - 1860 and 2460 Fertilizer Applicator
ELECTRICAL DIAGRAM
5
7
12
1
4
10
2
11
9
6
8
3
B-0190
ITEM
PART NUMBER
DESCRIPTION
QTY
1
SX006978
TURN SIGNAL MODULE, (PWI)
1
2
88665110
RED LIGHT HARNESS
1
3
88665111
AMBER LIGHT HARNESS
1
4
88665112
FRONT TO REAR HARNESS
1
5
SX014612
TRACTOR / IMPLEMENT HARNESS
1
6
SX21294
HEAVY DUTY CABLE TIE MOUNT
10
7
SX25510
INSULATED CLIP, 0.625” CLOSED, 0.281” HOLE
1
8
SX3NS12
STRAP, 11 1/4” BLA 21
11
9
SXBHF0381008YZ
BOLT, FLANGE, 3/8” x 1.00” GRADE 8 YELLOW ZINC
1
10
SXBM-10-24-125
BOLT, MACHINE 10-24 x 1.25”
2
11
SXLN-038-NIYZ
LOCKNUT, 3/8” NYLON INSERT NC YZ
4
12
SXLN-10-24-NI
LOCKNUT, 10/24 NYLON INSERT
2
142
Specifications - 1860 and 2460 Fertilizer Applicator
HARDWARE TORQUE VALUES
Metric Chart
NOTE: Do not use the values listed in the charts if a different torque value or tightening procedure is specified
in this manual for a specific application. Torque values listed are for general use only.
Use the following charts to determine the correct torque when checking, adjusting or replacing hardware. Torque
values are listed in newton-meters (inch* or foot pounds) for normal assembly applications.
Nominal
Size
Class 5.8
Class 8.8
Class 10.9
Lock nuts
Unplated
Plated
W / ZnCr
Unplated
Plated
W / ZnCr
Unplated
Plated
W / ZnCr
CL.8 w/
CL. 8.8 Bolt
M4
1.7 (15*)
2.2 (19*)
2.6 (23*)
3.4 (30*)
3.7 (33*)
4.8 (42*)
1.8 (16*)
M6
5.8 (51*)
7.6 (67*)
8.9 (79*)
12 (102*)
13 (115*)
17 (150*)
6.3 (56*)
M8
14 (124*)
18 (159*)
22 (195*)
28 (248*)
31 (274*)
40 (354*)
15 (133*)
M10
28 (21)
36 (27)
43 (32)
56 (41)
61 (45)
79 (58)
30 (22)
M12
49 (36)
63 (46)
75 (55)
97 (72)
107 (79)
138 (102)
53 (39)
M16
121 (89)
158 (117)
186 (137)
240 (177)
266 (196)
344 (254)
131 (97)
M20
237 (175)
307 (226)
375 (277)
485 (358)
519 (383)
671 (495)
265 (195)
M24
411 (303)
531 (392)
648 (478)
839 (619)
897 (662)
1160 (855)
458 (338)
NOTE: Torque values shown with * are inch pounds.
Identification of Hex Cap Screws and Carriage Bolts - Classes 5 and up
MANUFACTURER’S IDENTIFICATION
AB
CD
XYZ
8 8
8 8
PROPERTY CLASS
Identification of Hex Nuts and Lock Nuts - Classes 5 and up
MANUFACTURER’S IDENTIFICATION
AB
8
AB
8
AB
PROPERTY CLASS
143
Specifications - 1860 and 2460 Fertilizer Applicator
HARDWARE TORQUE VALUES (CONT’D)
Imperial Chart
NOTE: Do not use the values listed in the charts if a different torque value or tightening procedure is specified
in this manual for a specific application. Torque values listed are for general use only.
Use the following charts to determine the correct torque when checking, adjusting or replacing hardware. Torque
values are listed in newton-meters (inch* or foot pounds) for normal assembly applications.
Nominal
Size
SAE Grade 5
SAE Grade 8
Plated
W / ZnCr
LOCK NUTS
Unplated
or
Plated
Silver
Plated
W / ZnCr
Gold
Unplated
or
Plated
Silver
Grade
W / Gr. 5
Bolt
Grade
W / Gr. 8
Bolt
1/4
6.2 (55*)
8.1 (72*)
9.7 (86*)
6.9 (61*)
9.8 (86*)
5/16
13 (115*)
17 (149*)
20 (178*)
26 (229*)
28 (250*)
37 (324*)
14 (125*)
20 (176*)
3/8
23 (17)
30 (22)
35 (26)
46 (34)
50 (37)
65 (48)
26 (19)
35 (26)
7/16
37 (27)
47 (35)
57 (42)
73 (54)
80 (59)
104 (77)
41 (30)
57 (42)
1/2
57 (42)
73 (54)
87 (64)
113 (83)
123 (91)
159 (117)
61 (45)
88 (64)
9/16
81 (60)
104 (77)
125 (92)
163 (120)
176 (130)
229 (169)
88 (65)
125 (92)
5/8
112 (83)
145 (107)
174 (128)
224 (165)
244 (180)
316 (233)
122 (90)
172 (127)
3/4
198 (146)
256 (189)
306 (226)
397 (293)
432 (319)
560 (413)
217 (160)
306 (226)
7/8
193 (142)
248 (183)
495 (365)
641 (473)
698 (515)
904 (667)
350 (258)
494 (364)
1
289 (213)
373 (275)
742 (547)
960 (708)
1048 (773) 1356 (1000)
523 (386)
739 (545)
Gold
Unplated
or
Plated
Silver
Plated
W / ZnCr
Gold
12.6 (112*) 13.6 (121*) 17.7 (157*)
NOTE: Torque values shown with * are inch pounds.
Identification of Hex Cap Screws and Carriage Bolts
SAE GRADE
2 BOLTS
SAE GRADE
5 BOLTS
SAE GRADE
2 NUTS
SAE GRADE
8 BOLTS
SAE GRADE
2 NUTS
SAE GRADE
2 NUTS
Identification of Hex Nuts and Lock Nuts
B
Grade A - No Notches
Grade A - No Mark
Grade A - No Marks
Grade B - One Circumferential Notch
Grade B - Letter B
Grade B - Three Marks
Grade C - One Circumferential Notches
Grade C - Letter C
Grade C - Six Marks
(Marks not always located at corners)
144
Specifications - 1860 and 2460 Fertilizer Applicator
HYDRAULIC CONNECTION SPECIFICATIONS
O-Ring Fitting (Straight Thread)
Lubricate the O-ring before installing the fitting. Loosen
the jam nut and install the fitting. Tighten the jam nut until
the washer is tight against the surface.
Port Seal (O-ring Boss) Fitting
Figure 58
Port Seal And O-ring Boss Tightening Torque
Tubeline O.D.
Thread Size
N•m (ft-lb)
O-ring Face Seal Connection
1/4”
7/16” - 20
13 (18)
Figure 56
3/8”
9/16” - 18
22 (30)
1/2”
3/4” -1 6
40 (54)
5/8”
7/8” - 14
60 (81)
3/4”
1-1/16” - 12
84 (114)
7/8”
1-3/16” - 12
98 (133)
O-ring Face Seal Tightening Torque
Tubeline O.D.
Thread Size
N•m (ft-lb)
1/4”
9/16” - 18
13 (18)
3/8”
11/16” - 16
22 (30)
1/2”
13/16” - 16
40 (54)
5/8”
1” - 14
60 (81)
3/4”
1-3/16” - 12
84 (114)
7/8”
1-3/16” - 12
98 (133)
1”
1-7/16” - 12
118 (160)
1-11/16”
12
154
(209)
1-1/4”
2” - 12
1-1/2”
163 (221)
When the fitting is tightened, you can feel when the fitting
is tight to eliminate leakage caused by under or over
torqued fittings. Use petroleum jelly to hold the O-ring in
position until the fittings are assembled [Figure 56].
1”
1-5/16” - 12
118 (160)
1-1/8”
1-7/16” - 12
154 (209)
1-1/4”
1-5/8” - 12
163 (221)
NOTE: Port seal and nut, washer and O-ring (O-ring
Boss) fittings use the same tightening torque
valve chart [Figure 58].
If a torque wrench cannot be used, use the following
method.
Tighten the nut until it just makes metal to metal contact,
you can feel the resistance.
Flare Fitting
Tighten the nut with a wrench no more than one hex flat
maximum.
Figure 57
Do not over tighten the port seal fitting.
Flare Fitting Tightening Torque
Tubeline O.D.
Thread Size
N•m (ft-lb)
1/4”
7/16” - 20
13 (18)
5/16”
1/2” - 20
17 (23)
3/8”
9/16” - 18
22 (30)
1/2”
3/4” - 16
40 (54)
5/8”
7/8” - 14
60 (81)
3/4”
1-1/16” - 12
84 (114)
7/8”
1-3/16” - 12
98 (133)
1”
1-5/16” - 12
118 (160)
1-1/4”
1-5/8” - 12
154 (209)
1-1/2”
1-7/8” - 12
163 (221)
2”
2-1/2” - 12
252 (342)
Tighten until the nut makes contact with the seat. Use the
chart [Figure 57] to find the correct tightness needed.
NOTE: If a torque wrench cannot be used, use the
hex flat tightening method as an approximate
guideline.
NOTE: Port seal fittings are not recommended in all
applications. Use O-ring boss fittings in these
applications.
Tubelines And Hoses
Replace any tubelines that are bent or flattened. They will
restrict flow, which will slow hydraulic action and cause
heat.
Replace hoses which show signs of wear, damage or
weather cracked rubber.
Always use two wrenches when loosening and tightening
hose or tubeline fittings.
NOTE: If the fitting leaks, disconnect and inspect the
seat area for damage.
145
Specifications - 1860 and 2460 Fertilizer Applicator
NOZZLE SELECTION
Use the following formula to covert pounds per acre to gallons per minute (gpm):
Total lb. per acre = Target lb. per acre
Percent of nitrogen
of nitrogen
Total lb. per acre = GPA
Pound per gallon
EXAMPLE - The desired output is 100 lbs of nitrogen per acre. In order to get 100 lbs of nitrogen you need to apply
357 lbs of 28% nitrogen solution per acre. 357 lbs per acre of a solution that weighs 10.65 lbs per gallon equals
33.53 gallons per acre (GPA). Select a nozzle that will provide 33.53 GPA at your desired system pressure.
Total lb. per acre: 357 = 100
0.28
of nitrogen
357 = 33.53 GPA
10.65
Density Correction Chart
WEIGHT OF SOLUTION
PER GALLON
SPECIFIC GRAVITY
CONVERSION FACTOR
7.00 lb.
0.84
0.92
8.00 lb.
0.96
0.98
1.00
1.00
1.08
1.04
8.34 lb.
EXAMPLE
Water
9.00 lb.
10.00 lb.
1.20
1.10
10.65 lb.
28% Nitrogen
1.28
1.13
11.00 lb.
7 - 27 - 7 Fertilizer
1.32
1.15
11.06 lb.
32% Nitrogen
1.33
1.15
11.40 lb.
10 - 34 - 0 Fertilizer
1.37
1.17
11.50 lb.
12 - 0 - 0 - 26 Fertilizer
1.38
1.17
11.60 lb.
11 - 37 - 0 Fertilizer
1.43
1.20
12.00 lb.
1.44
1.20
14.00 lb.
1.68
1.30
Additional Useful Formula:
GPM = GPA x MPH x W
5940
(per nozzle)
MPH = Distance in feet x 60
Time in seconds x 88
GPA = GPM (per nozzle) x 5940
MPH x W
W = Nozzle spacing in inches
Spacing Correction Chart
NOZZLE SPACING
CONVERSION FACTOR
22 in.
36 in.
38 in.
1.36
0.83
0.79
GPA Target Conversion Factor
= Corrected GPA
NOTE: For nozzle spacing not shown, use this formula: Conversion Factor = Nozzle spacing in table
Your nozzle spacing
146
Specifications - 1860 and 2460 Fertilizer Applicator
NOZZLE SPECIFICATIONS
GPA AT 30” NOZZLE SPACING**
NOZZLE*
PSI
GPM
(Per Nozzle)
4 MPH
6 MPH
8 MPH
10 MPH
H1/4U - SS0004
10
20
30
40
10
20
30
40
10
20
30
40
10
20
30
40
10
20
30
40
10
20
30
40
10
20
30
40
10
20
30
40
10
20
30
40
10
20
30
40
0.20
0.28
0.35
0.40
0.30
0.42
0.52
0.60
0.40
0.57
0.69
0.80
0.50
0.71
0.87
1.00
0.75
1.06
1.30
1.50
1.00
1.41
1.73
2.00
1.50
2.12
2.60
3.00
2.50
3.54
4.53
5.00
3.00
4.24
5.20
6.00
3.00
4.24
5.20
6.00
9.9
13.9
17.3
19.8
14.9
20.8
25.7
29.7
19.8
28.2
34.2
39.6
24.8
35.1
43.1
49.5
37.1
52.5
64.4
74.3
49.5
69.8
85.6
99.0
74.3
104.9
128.7
148.5
123.8
175.2
224.2
247.5
148.5
209.9
257.4
297.0
148.5
209.9
257.4
297.0
6.6
9.2
11.6
13.2
9.9
13.9
17.2
19.8
13.2
18.8
22.8
26.4
16.5
23.4
28.7
33.0
24.8
35.0
42.9
49.5
33.0
46.5
57.1
66.0
49.5
70.0
85.8
99.0
82.5
116.8
149.5
165.0
99.0
139.9
171.6
198.0
99.0
139.9
171.6
198.0
5.0
6.9
8.7
9.9
7.4
10.4
12.9
14.9
9.9
14.1
17.1
19.8
12.4
17.6
21.5
24.8
18.6
26.2
32.2
37.1
24.8
34.9
42.8
49.5
37.1
52.5
64.4
74.3
61.9
87.6
112.1
123.8
74.3
104.9
128.7
148.9
74.3
104.9
128.7
148.9
4.0
5.5
6.9
7.9
5.9
8.3
10.3
11.9
7.9
11.3
13.7
15.8
9.9
14.1
17.2
19.8
14.9
21.0
25.7
29.7
19.8
27.9
34.3
39.6
29.7
42.0
51.5
59.4
49.5
70.1
89.7
99.0
59.4
84.0
103.0
84.0
59.4
84.0
103.0
84.0
H1/4U - SS0006
H1/4U - SS0008
H1/4U - SS0010
H1/4U - SS0015
H1/4U - SS0020
H1/4U - SS0030
H1/4U - SS0040
H1/4U - SS0050
H1/4U - SS0060
* Nozzle or tip (TP). Tip used with the standard TeeJet® cap. Nozzles are threaded with BSPT threads.
** Use the conversion factor for other nozzle spacings.
147
Specifications - 1860 and 2460 Fertilizer Applicator
148
Warranty - 1860 and 2460 Fertilizer Applicator
WARRANTY
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
149
Warranty - 1860 and 2460 Fertilizer Applicator
150
Warranty - 1860 and 2460 Fertilizer Applicator
WARRANTY
Limited Warranty
BASE LIMITED WARRANTY
Farm King provides this warranty only to original retail purchasers of its products. Farm King warrants to such
purchasers that all Farm King manufactured parts and components used and serviced as provided for in the
Operator’s Manual shall be free from defects in materials and workmanship for a period following delivery to
the original retail purchaser of one (1) year. This limited warranty applies only to those parts and components
manufactured by Farm King. Parts and components manufactured by others are subject to their
manufacturer’s warranties, if any.
Farm King will fulfill this limited warranty by, at its option, repairing or replacing any covered part that is
defective or is the result of improper workmanship, provided that the part is returned to Farm King within thirty
(30) days of the date that such defect or improper workmanship is, or should have been, discovered. Parts
must be returned through the selling representative and the buyer must prepay transportation charges.
Farm King will not be responsible for repairs or replacements that are necessitated, in whole or part, by the
use of parts not manufactured by or obtained from Farm King. Under no circumstances are component parts
warranted against normal wear and tear. There is no warranty on product pump seals, product pump bearings,
rubber product hoses, pressure gauges, or other components that require replacement as part of normal
maintenance.
REPAIR PARTS LIMITED WARRANTY
Farm King warrants genuine Farm King replacement parts purchased after the expiration of the Farm King
Limited Warranty, and used and serviced as provided for in the Operator’s Manual, to be free from defects in
materials or workmanship for a period of thirty (30) days from the invoice date for the parts. Farm King will
fulfill this limited warranty by, at its option, repairing or replacing any covered part that is defective or is the
result of improper workmanship, provided that the part is returned to Farm King within thirty (30) days of the
date that such defect or improper workmanship is, or should have been, discovered. Such parts must be
shipped to the Farm King factory at the purchaser’s expense.
WHAT IS NOT COVERED
Under no circumstances does this limited warranty cover any components or parts that have been subject to
the following: negligence; alteration or modification not approved by Farm King; misuse; improper storage;
lack of reasonable and proper maintenance, service, or repair; normal wear; damage from failure to follow
operating instructions; accident; and/or repairs that have been made with parts other than those
manufactured, supplied, and or authorized by Farm King.
AUTHORIZED DEALER AND LABOR COSTS
Repairs eligible for labor under this limited warranty must be made by Farm King or an authorized Farm King
dealer. Farm King retains the exclusive discretion to determine whether it will pay labor costs for warranty
repairs or replacements, and the amount of such costs that it will pay and the time in which the repairs will be
made. If Farm King determines that it will pay labor costs for warranty work, it will do so by issuing a credit to
the dealer’s or distributor’s account. Farm King will not approve or pay invoices sent for repairs that Farm King
has not previously approved. Warranty service does not extend the original term of this limited warranty.
151
Warranty - 1860 and 2460 Fertilizer Applicator
Limited Warranty
WARRANTY REQUIREMENTS
To be covered by warranty, each new product must be registered with Farm King within thirty (30) days of
delivery to original retail purchaser. If the customer decides to purchase replacement components before the
warranty disposition of such components is determined, Farm King will bill the customer for such
components and then credit the replacement invoice for those components later determined to be covered by
this limited warranty. Any such replacement components that are determined not be covered by this limited
warranty will be subject to the terms of the invoice and shall be paid for by the purchaser.
EXCLUSIVE EFFECT OF WARRANTY AND LIMITATION OF LIABILITY
TO THE EXTENT PERMITTED BY LAW, FARM KING DISCLAIMS ANY WARRANTIES, REPRESENTATIONS, OR
PROMISES, EXPRESS OR IMPLIED, AS TO THE QUALITY, PERFORMANCE, OR FREEDOM FROM DEFECT OF
THE COMPONENTS AND PARTS COVERED BY THIS WARRANTY AND NOT SPECIFICALLY PROVIDED FOR
HEREIN.
TO THE EXTENT PERMITTED BY LAW, FARM KING DISCLAIMS ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ON ITS PRODUCTS COVERED HEREIN,
AND DISCLAIMS ANY RELIANCE BY THE PURCHASER ON FARM KING’S SKILL OR JUDGMENT TO SELECT
OR FURNISH GOODS FOR ANY PARTICULAR PURPOSE. THE PURCHASER’S ONLY AND EXCLUSIVE
REMEDIES IN CONNECTION WITH THE BREACH OR PERFORMANCE OF ANY WARRANTY ON FARM KING’S
Product S ARE THOSE SET FORTH HEREIN. IN NO EVENT SHALL FARM KING BE LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES (INCLUDING, BY WAY OF EXAMPLE ONLY AND NOT LIMITATION, LOSS OF
CROPS, LOSS OF PROFITS OR REVENUE, OTHER COMMERCIAL LOSSES, INCONVENIENCE, OR COST OF
REPLACEMENT OF RENTAL EQUIPMENT). IN NO EVENT SHALL FARM KING’S CONTRACT OR WARRANTY
LIABILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT. (Note that some states do not allow limitations
on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages,
so the above limitations and exclusion may not apply to you.) This warranty gives you specific legal rights and
you may also have other rights, which vary from state to state.
Farm King neither assumes nor authorizes any person or entity, including its selling representatives, to
assume any other obligations or liability in connections with the sale of covered equipment, or to make any
other warranties, representations, or promises, express or implied, as to the quality, performance, or freedom
from defect of the components and parts covered herein. No one is authorized to alter, modify, or enlarge this
limited warranty, or its exclusions, limitations and reservations.
Corrections of defects and improper workmanship in the manner, and for the applicable time periods, provided
for herein shall constitute fulfillment of all responsibilities of Farm King to the purchaser, and Farm King shall
not be liable in negligence, contract, or on any other basis with respect to the subject equipment.
This limited warranty is subject to any existing conditions of supply which may directly affect Farm King’s
ability to obtain materials or manufacturer replacement parts.
Buhler Industries Inc. reserves the right to make improvements in design or changes in specifications to its
products at anytime, without incurring any obligation to owners of units previously sold.
152
Alphabetical Index - 1060 and 1360 Grain Cart
ALPHABETICAL INDEX
AXLE GROUP . . . . . . . . . . . . . . . . . . . . . . . 71
CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . 63
COMPONENT INSTALLATION . . . . . . . . . . 25
CONTROL VALVE . . . . . . . . . . . . . . . . . . . 136
COULTER ARM ASSEMBLY . . . . . . . . . . . 116
COULTER ASSEMBLY (STRAIGHT) . . . . . 112
COULTER BRACKET GROUP . . . . . . . . . . 106
COULTER MOUNTING ASSEMBLY . . . . . 118
COULTER W / INJECT GROUP . . . . . . . . 110
COULTER W / KNIFE GROUP . . . . . . . . . 108
ELECTRICAL DIAGRAM . . . . . . . . . . . . . . 142
EQUIPMENT DECALS AND SIGNS . . . . . . 21
EQUIPMENT IDENTIFICATION . . . . . . . . . . . 8
FERTILIZER APPLICATOR OPERATION . . 43
FIELD OPERATION . . . . . . . . . . . . . . . . . . . 51
FIRE PREVENTION . . . . . . . . . . . . . . . . . . . 16
FOLD LINKAGE GROUP . . . . . . . . . . . . . . . 92
FORWARD PRODUCT PUMP GROUP . . . 100
FRAME GROUP . . . . . . . . . . . . . . . . . . . . . . 72
GAUGE WHEEL GROUP LH . . . . . . . . . . . 119
GAUGE WHEEL GROUP RH . . . . . . . . . . 120
GAUGE WHEEL HUB . . . . . . . . . . . . . . . . 121
GENERAL INFORMATION . . . . . . . . . . . . . 37
GENERAL PARTS INFORMATION . . . . . . . 71
HAND / EYE WASH GROUP . . . . . . . . . . . . 86
HARDWARE TORQUE VALUES . . . . . . . . 143
HITCH GROUP . . . . . . . . . . . . . . . . . . . . . 130
HUB ASSEMBLY . . . . . . . . . . . . . . . . . . . . 126
HYDRAULIC CONNECTION
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . 145
HYDRAULIC DIAGRAM . . . . . . . . . . . . . . . 140
INITIAL SET-UP . . . . . . . . . . . . . . . . . . . . . . 40
INNER FOLD CYLINDER . . . . . . . . . . . . . 133
LIGHTING MARKING GROUP . . . . . . . . . 128
LUBRICATION . . . . . . . . . . . . . . . . . . . . . . . 61
MAIN LIFT CYLINDER (LH) . . . . . . . . . . . . 134
MAIN LIFT CYLINDER (RH) . . . . . . . . . . . 135
NOZZLE SELECTION . . . . . . . . . . . . . . . . 146
NOZZLE SPECIFICATIONS . . . . . . . . . . . . 147
OUTER WING CYLINDER . . . . . . . . . . . . . 132
OWNER’S INFORMATION . . . . . . . . . . . . . . . 7
PRODUCT PLUMBING GROUP . . . . . . . . . 94
PRODUCT PUMP ASSEMBLY . . . . . . . . . . . 98
PRODUCT PUMP GROUP . . . . . . . . . . . . . 96
QUICK FILL GROUP . . . . . . . . . . . . . . . . . 101
RAVEN 450 . . . . . . . . . . . . . . . . . . . . . . . . 127
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . 13
SAFETY SIGN (DECAL) INSTALLATION . . . 64
SAFETY SIGN-OFF FORM . . . . . . . . . . . . . 22
SAFETY SIGNS (DECALS) . . . . . . . . . . . . . 19
SERVICE SCHEDULE . . . . . . . . . . . . . . . . . 60
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . 139
STORAGE AND RETURN TO SERVICE . . . 65
TANK ASSEMBLY . . . . . . . . . . . . . . . . . . . . . 82
TANK BAFFLE GROUP . . . . . . . . . . . . . . . . 84
TANK SUPPORT FRONT . . . . . . . . . . . . . . . 78
TANK SUPPORT GROUP . . . . . . . . . . . . . . 76
TANK SUPPORT REAR . . . . . . . . . . . . . . . . 80
TIRE / WHEEL SINGLE 380 / 90 R54 . . . . 122
TIRE / WHEEL SINGLE 380 / 90 R54 . . . . 123
TIRE / WHEEL STRADDLE DUAL 320 / 90
R54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
TIRE / WHEEL STRADDLE DUAL 320 / 90
R54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
TOOLBAR GROUP . . . . . . . . . . . . . . . . . . . 88
TOOLBAR PLUMBING GROUP . . . . . . . . . 102
TRANSPORTING . . . . . . . . . . . . . . . . . . . . . 55
TROUBLESHOOTING . . . . . . . . . . . . . . . . . 59
WARRANTY REGISTRATION FORM . . . . . . 3
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . 151
153
Alphabetical Index - 1060 and 1360 Grain Cart
154
www.farm-king.com
2500 Airport Drive SW
Willmar, MN USA 56201
Toll Free: 1-888-FK-80001
E-mail: info@buhler.com
www.farm-king.com
Equipment shown is subject to change without notice.
©2012 Buhler Trading Inc. Printed in Canada TSX:BUI
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising