ULN2803AP,ULN2803AFW,ULN2804AP,ULN2804AFW (Manufactured by Toshiba Malaysia) ULN2803,04AP/AFW 8CH DARLINGTON SINK DRIVER

ULN2803AP,ULN2803AFW,ULN2804AP,ULN2804AFW (Manufactured by Toshiba Malaysia) ULN2803,04AP/AFW 8CH DARLINGTON SINK DRIVER
ULN2803,04AP/AFW
TOSHIBA BIPOLAR DIGITAL INTEGRATED CIRCUIT SILICON MONOLITHIC
ULN2803AP,ULN2803AFW,ULN2804AP,ULN2804AFW
(Manufactured by Toshiba Malaysia)
8CH DARLINGTON SINK DRIVER
The ULN2803AP / AFW Series are high−voltage, high−current
darlington drivers comprised of eight NPN darlington pairs.
All units feature integral clamp diodes for switching inductive
loads.
Applications include relay, hammer, lamp and display (LED)
drivers.
FEATURES
Output current (single output)
500 mA (Max.)
High sustaining voltage output
50 V (Min.)
Output clamp diodes
Inputs compatible with various types of logic.
Package Type−AP
: DIP−18pin
Package Type−AFW
: SOL−18pin
Weight
DIP18−P−300−2.54F: 1.478 g (Typ.)
SOL18−P−300−1.27 : 0.48 g (Typ.)
PIN CONNECTION (TOP VIEW)
INPUT BASE
RESISTOR
DESIGNATION
ULN2803AP / AFW
2.7 kΩ
TTL, 5 V CMOS
ULN2804AP / AFW
10.5 kΩ
6~15 V PMOS, CMOS
TYPE
1
2001-07-05
ULN2803,04AP/AFW
SCHEMATICS (EACH DRIVER)
ULN2803AP / AFW
Note:
ULN2804AP / AFW
The input and output parasitic diodes cannot be used as clamp diodes.
MAXIMUM RATINGS (Ta = 25°C)
CHARACTERISTIC
Output Sustaining Voltage
SYMBOL
RATING
UNIT
VCE (SUS)
−0.5~50
V
Output Current
IOUT
500
mA / ch
Input Voltage
VIN
−0.5~30
V
Clamp Diode Reverse Voltage
VR
50
V
Clamp Diode Forward Current
IF
500
mA
Power Dissipation
AP
AFW
PD
1.47
0.92 / 1.31 (Note)
W
Operating Temperature
Topr
−40~85
°C
Storage Temperature
Tstg
−55~150
°C
Note:
On Glass Epoxy PCB (75 × 114 × 1.6 mm Cu 20%)
2
2001-07-05
ULN2803,04AP/AFW
RECOMMENDED OPERATING CONDITIONS (Ta = −40~85°C)
CHARACTERISTIC
Output Sustaining Voltage
SYMBOL
IOUT
AFW
Input Voltage
Input Voltage
(Output On)
MIN
TYP.
MAX
UNIT
0
―
50
V
Tpw = 25 ms, Duty = 10%,
8 Circuits
0
―
347
Tpw = 25 ms, Duty = 50%,
8 Circuits
0
―
123
Tpw = 25 ms, Duty = 10%,
8 Circuits
0
―
268
Tpw = 25 ms, Duty = 50%,
8 Circuits
0
―
90
0
―
30
3.5
―
30
VCE (SUS)
AP
Output Current
TEST CONDITION
VIN
ULN2803AP
/ AFW
ULN2804AP
/ AFW
VIN (ON)
mA /
ch
V
V
8
―
30
Clamp Diode Reverse Voltage
VR
―
―
50
V
Clamp Diode Forward Current
IF
―
―
400
mA
―
―
0.76
―
―
0.48
Power Dissipation
Note:
AP
AFW
PD
Ta = 85°C
Ta = 85°C
(Note)
W
On Glass Epoxy PCB (75 × 114 × 1.6 mm Cu 20%)
3
2001-07-05
ULN2803,04AP/AFW
ELECTRICAL CHARACTERISTICS (Ta = 25°C)
CHARACTERISTIC
Output Leakage Current
SYMBOL
TEST
CIR−
CUIT
ICEX
1
ULN2804AP / AFW
Collector−Emitter Saturation Voltage
VCE (sat)
2
ULN2803AP / AFW
Input Current
ULN2804AP / AFW
IIN (ON)
IIN (OFF)
2
4
ULN2803AP / AFW
Input Voltage
(Output On)
VIN (ON)
5
ULN2804AP / AFW
DC Current Transfer Ratio
hFE
2
Clamp Diode Reverse Current
IR
6
Clamp Diode Forward Voltage
VF
7
Input Capacitance
CIN
―
Turn−On Delay
tON
Turn−Off Delay
tOFF
Note:
8
TEST CONDITION
MIN
TYP.
MAX
VCE = 50 V
Ta = 25°C
―
―
50
VCE = 50 V
Ta = 85°C
―
―
100
VCE = 50 V
VIN = 1 V
―
―
500
IOUT = 350 mA, IIN = 500 µA
―
1.3
1.6
IOUT = 200 mA, IIN = 350 µA
―
1.1
1.3
IOUT = 100 mA, IIN = 250 µA
―
0.9
1.1
VIN = 3.85 V
―
0.93
1.35
VIN = 5 V
―
0.35
0.5
VIN = 12 V
―
1.0
1.45
IOUT = 500 µA, Ta = 85°C
50
65
―
VCE = 2 V, IOUT = 200 mA
―
―
2.4
VCE = 2 V, IOUT = 250 mA
―
―
2.7
VCE = 2 V, IOUT = 300 mA
―
―
3.0
VCE = 2 V, IOUT = 125 mA
―
―
5.0
VCE = 2 V, IOUT = 200 mA
―
―
6.0
VCE = 2 V, IOUT = 275 mA
―
―
7.0
VCE = 2 V, IOUT = 350 mA
―
―
8.0
VCE = 2 V, IOUT = 350 mA
1000
―
―
UNIT
µA
V
mA
µA
V
Ta = 25°C
(Note)
―
―
50
Ta = 85°C
(Note)
―
―
100
―
―
2.0
V
―
15
―
pF
RL = 125 Ω, VOUT = 50 V
―
0.1
―
RL = 125 Ω, VOUT = 50 V
―
0.2
―
IF = 350 mA
µA
µs
VR = VR MAX.
4
2001-07-05
ULN2803,04AP/AFW
TEST CIRCUIT
1.
ICEX
2.
VCE (sat), hFE
3.
IIN (ON)
4.
IIN (OFF)
5.
VIN (ON)
6.
IR
7.
VF
5
2001-07-05
ULN2803,04AP/AFW
8.
tON, tOFF
Note 1: Pulse Width 50 µs, Duty Cycle 10%
Output Impedance 50 Ω, tr ≤ 5 ns, tf ≤ 10 ns
Note 2: See below.
INPUT CONDITION
TYPE NUMBER
R1
VIH
ULN2803AP / AFW
0Ω
3V
ULN2804AP / AFW
0Ω
8V
Note 3: CL includes probe and jig capacitance
PRECAUTIONS for USING
This IC does not integrate protection circuits such as overcurrent and overvoltage protectors.
Thus, if excess current or voltage is applied to the IC, the IC may be damaged. Please design the IC so that
excess current or voltage will not be applied to the IC.
Utmost care is necessary in the design of the output line, COMMON and GND line since IC may be destroyed
due to short−circuit between outputs, air contamination fault, or fault by improper grounding.
6
2001-07-05
ULN2803,04AP/AFW
7
2001-07-05
ULN2803,04AP/AFW
8
2001-07-05
ULN2803,04AP/AFW
PACKAGE DIMENSIONS
DIP18−P−300−2.54F
Unit: mm
Weight: 1.478 g (Typ.)
9
2001-07-05
ULN2803,04AP/AFW
PACKAGE DIMENSIONS
SOL18−P−300−1.27
Unit: mm
Weight: 0.48 g (Typ.)
10
2001-07-05
ULN2803,04AP/AFW
RESTRICTIONS ON PRODUCT USE
000707EBA
• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc..
• The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this
document shall be made at the customer’s own risk.
• The products described in this document are subject to the foreign exchange and foreign trade laws.
• The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other
rights of the third parties which may result from its use. No license is granted by implication or otherwise under
any intellectual property or other rights of TOSHIBA CORPORATION or others.
• The information contained herein is subject to change without notice.
11
2001-07-05
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising