Manual 12691654

Manual 12691654
DMS-20PC-1-LM
www.murata-ps.com
Self-Powered 3 Digit, LED Display
AC Line Voltage Monitors
FEATURES
■
Plugs directly into USA-style wall outlets
■
Screw terminals for panel mounting
■
Small 1.38" x 0.88" x 1.0" packages
■
Large, easy-to-read, red, blue or green LED displays
■
Fully encapsulated for harsh environments
■
Half-wave averaging, rms calibrated
■
UL, CSA and IEC1010-1 certified
■
Very low cost!
Functional Specifications
Input
Voltage Range ➀
Overvoltage Protection
Frequency Range ➀
Current Consumption
Performance
Sampling Rate
Measurement Type
85-264Vrms
300Vrms
(Overvoltage category II)
47-63Hz
50mArms (max.)
2.5 readings/second
Half-wave average, rms
calibrated for sinusoidal input
±1V (typ.), ±2V (max.)
Accuracy @ +25°C
Temperature Drift
(–25 to +60°C)
±0.15 Volts/°C (max.)
Mechanical
Dimensions
Display Type
Weight
Case Material
6-32 screw torque
1.38" x 0.88" x 1.00"
3 digit, red LED, 0.37"/9.4mm
1 ounce (28 grams)
Polycarbonate
6-8 in-lb (0.7 – 0.9N-m)
Murata Power Solution's DMS-20PC-1-LM is a component-size, self-contained, low-cost
ac voltmeter for true line measurements. It requires no additional components or auxiliary
power. Simply plug it into any wall outlet and instantly read voltages from 85 to 264Vac
(47-63Hz). The large (0.37"/9.4mm), bright red, blue or green LED display makes the
DMS-20PC-1-LM easily readable under any lighting conditions.
DMS-20PC-1-LM employs half-wave
sinusoidal averaging (rms calibrated) and has
DMS-20PC-1-LM-F
a display resolution of 1Vac over its full input
(Blade Terminals)
range. Packaged in a red-filter case with builtin bezel, the meter is fully encapsulated for
ruggedness. All units are overvoltage protected
DMS-20PC-1-LM
(Panel Mount)
to 300Vac.
This low-cost meter is ideal for industrial,
laboratory, office and field-service applications. Its miniature size is perfect for design
into high-end consumer electronics, laboratory
instrumentation and other products requiring
accurate ac line monitoring.
Suggested wiring (user supplied)
Ordering Information
DMS-20PC-1-LM-C
DMS-20PC-1-LM-B-C
DMS-20PC-1-LM-G-C
DMS-20PC-1-LM-F-C
DMS-20PC-1-LM-BF-C
DMS-20PC-1-LM-GF-C
DMS-20-CP
DMS-BZL3-C
DMS-BZL4-C
Red LED with threaded standoffs ➁
Blue LED with threaded standoffs ➁
Green LED with threaded standoffs ➁
Red LED with blade terminals
Blue LED with blade terminals
Green LED with blade terminals
Optional panel cutout punch
Optional panel mount bezel
Optional panel mount bezel with sealing gasket
➁ Brass screws (6-32 thread) and a panel-mount retaining clip are supplied with meter.
Environmental
Operating Temperature
–25 to +60°C
Storage Temperature
–40 to +75°C
Humidity (Non-condensing)
0 to 95%
➀ Operation and accuracy at inputs above or below these ranges are not specified.
FUSED
AC POWER
SUPPLY
For full details go to
www.murata-ps.com/rohs
C
®
Typical Connection Diagram
US E156931
www.murata-ps.com/support
MPM_DMS-20PC-1-LM.C07 Page 1 of 2
DMS-20PC-1-LM
Self-Powered 3 Digit, LED Display
AC Line Voltage Monitors
Power Supply Polarity, Fusing, Wiring, and Grounding: DMS-20PC-1-LM’s
two ac-supply terminals are not polarity sensitive, that is, they have no “AC LO”
or “AC HI” designations. These units do not include nor require a connection to
earth/chassis ground.
All ac-supply wiring must be rated for the voltages and currents they will
conduct and comply with any code or application-mandated requirements
pertaining to the user’s specific installation. 300V UL rated wire suitable for the
intended application is required.
DMS-20PC-1-LM ac voltmeters are not internally fused. The rear threaded
standoff input-terminals are to be used only for powering the voltmeter’s
internal circuitry; they must not be used to supply power to external loads.
Except for plug-in models with blade terminals, which must be protected by an
external system circuit breaker or fuse, the supply wires feeding these voltmeters must be fused with a 0.25A/250V time delay/time lag fuse, in accordance
with applicable regulatory codes.
The recommended wire size is 16AWG to 20AWG (1.31mm2 to 0.52mm2)
stranded copper wire. Wires must be properly stripped and attached to the
threaded standoffs such that their insulation is not pinched by the supplied
6-32 screws. Rated tightening torque for the 6-32 screws is 7 to 8 poundinches (0.8 to 0.9N-m).
1.30
(33.0)
DMS-20PC-1-LM
®
®
0.04
(1.016)
0.04
(1.016)
#6-32
UNC THD
0.44
(11.2)
0.75
(19.1)
0.80
(20.3)
0.32
(8.1)
0.88
(22.4)
0.10
(2.5)
C
®
1.38
(35.1)
0.37
(9.4)
1.00
(25.4)
#2-56 INSERT
0.156 (3.96) DEEP
1.07
(27.2)
0.04
(1.016)
DMS-BZL3-C
Optional Bezel
1.63 (41.4)
1.83 (46.5)
0.19
(4.8)
1.28
(32.5)
0.10
(2.5)
Dimensions in inches (millimeters)
Tolerances: 2 PL Dec ±0.02 (±0.51)
3 PL Dec ±0.010 (±0.254)
Recommended panel cutout dimensions:
1.336 (33.93)W × 0.838 (21.29)H
Internal corner radii 0.032 (0.81) Max.
US E156931
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
ISO 9001 and 14001 REGISTERED
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
notice.
© 2012 Murata Power Solutions, Inc.
www.murata-ps.com/support
MPM_DMS-20PC-1-LM.C07 Page 2 of 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising