AdapTec-X is a basic accessory suggested for FingerTec

AdapTec-X is a basic accessory suggested for FingerTec
AdapTec-X is a basic accessory suggested for FingerTec
access control systems. It enhances access control
functionalities as well as eases the installation process
with its encrypted communication and secure I/O
expansion features and all theses features are
compressed into a sleek casing to deliver a cost
effective solution.
Enhanced Security with
Encrypted Signals*
Power Up Terminals & Door
Lock Systems
It supports FingerTec encrypted
26-bit Wiegand communication
output; providing enhanced security
level for extra protection.
A single AdapTec-X can support a
maximum of 2 units of FingerTec
terminals and 2 sets of door lock
accessories such as the EM Lock and
drop bolt in one single system
installation.
Prolonged Life Span of
Hardware
Control IN/OUT Terminals At
An Entrance
With data encryption, the life span of
the terminals can be prolonged
without the risk of short circuiting
when using AdapTec-X.
AdapTec-X is a perfect choice for an
IN/OUT installation, where a door is
controlled both at the entrance and
the exit.
Power Supply and Battery
AdapTec-X connects to a 12VDC
switching power supply as power
input to operate, and a 12VDC
rechargeable backup battery to
provide power to ensure protection
of access during any events of power
failure.
Seamless Integration with
FingerTec Terminals
Mix and match the FingerTec
terminals via AdapTec-X for a cost
effective access control system
suitable for small and medium sized
offices.
Alert Emergency with Siren
Compatible with an NC siren type
with a maximum of 0.5A load for
emergency event. E.g. if the
terminal
is
being
illegally
dismantled.
DIY Metal Casing for Cleaner
Installation
Store AdapTec-X, with its power
supply and a backup battery in an
exclusive FingerTec DIY metal
casing, providing a cleaner
installation.
LAYOUT PLAN
WEB LINK
Installation Guide
http://info.fingertec.com/adaptec-x-1
Installation Diagram
Power cable and door unlock signals
for illustration only
CAT5 / TCP/IP cable for data transfer
Door lock system
Video Guide
http://info.fingertec.com/adaptec-x-2
AC110/240V
Power Input
Switching
power supply
12VDC
DC12V Rechargeable
battery
ABOVE CEILING
CEILING
Override
Key Switch
Hub/Switch
EM Lock
w
1
2
3
4
5
6
7
8
9
0
MENU
Emergency
Break
Glass
ESC
OK
R2
FingerTec
Terminal
Push Button
PC
OUTDOOR
INDOOR
NETWORKING
*How AdapTec-X Enhances Security
To provide you enhanced security, AdapTec-X will only recognize encrypted Wiegand signals from FingerTec terminals in order to unlock its doors.
The code of the encrypted signals is written into the firmware of FingerTec terminals, which cannot be duplicated into other devices. This prevents
hackers from bypassing this by simply providing the relay signal to AdapTec-X. Furthermore, separate power outputs for the door lock system and
FingerTec terminals will keep the door locked even during any failures (i.e.: vandalism to terminals, etc.). For added security, a siren output port is
ready to be linked up to alarms or sirens to produce alert sounds in case of forced door openings.
SPECIFICATIONS
PHYSICAL APPEARANCE
Surface finishing
Acrylonitrile Butadiene Styrene (ABS)
Dimension, mm
85 x 96 x 33
Weight, kg
0.1
CPU
High Performance RISC CPU
POWER SUPPLY
Power input
12VDC 3A
Power output
12VDC 3A
Backup Power system
UPS or 12VDC Rechargeable battery
INPUT – OUTPUT SIGNAL
Input signal
26-bit FingerTec encrypted Weigand signal
Output signal
12VDC 0.5A Siren
12VDC 3A EM output (NO/NC Type door locks)
ALERTS & NOTIFICATIONS
Over input voltage
Yes, 3 long beeps
Door release
Yes, 2 short beeps
Door forced open
Yes, continuous beeps (May opt to output external siren system)
Illegal dismantling of FingerTec terminals
Yes, continuous beeps (May opt to output external siren system)
Door unlock timer
VR type, LED blinks to indicate unlock time in Seconds
On Board LED indicators
EM LED lit up – Door lock output is working
Status LED lit up – CPU is working
Battery low LED lit up – Battery is low and cut-off
ON-BOARD PROTECTION
Over voltage alarm
> 15 VDC
Packaging
Fuses
PTC type
Dimension (mm) : 173 (L) x 60 (W) x 135 (H)
Weight
: 0.3 kg
Battery cut-off
8.5 ~ 9.5 VDC
NOTE: Specifications are subject to change. Check http://product.fingertec.com for latest product information.
Authorized Reseller:
www.fingertec.com
© 2000-2014 FingerTec Worldwide Limited. All rights reserved.
062014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising