Bissell 3596 User`s guide
CleanView / Power Trak
®
B A G L E S S
®
R E V O L U T I O N ™
USER’S GUIDE
6591/3595/3596/43B0/53F8/62N7 SERIES
3
Safety Instructions
4
Product View
5-6 Assembly Instructions
7-9 Operation / Special Tools
10-13 Maintenance
13
14
15
16
Consumer Services
Troubleshooting
Replacement Parts
Warranty
1.
Thanks For Buying A BISSELL Vacuum
We’re glad you purchased a BISSELL Vacuum. Everything we know about floor
care went into the design and construction of this complete, high-tech home
vacuuming system.
Your BISSELL Vacuum is well made, and we back it with a limited
comprehensive one-year warranty. We also stand behind it with a
knowledgeable, dedicated Consumer Services Department, so, should you ever
have a problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a
global leader in the design, manufacture, and service of high quality homecare
products like your BISSELL Vacuum.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
President and Chief Executive Officer
1.
2
Important Safety Instructions
When using an electrical appliance, basic
precautions should be observed, including
the following:
Read all instructions
before using your
upright VACUUM.
Always connect to a polarized outlet (left slot is
wider than right). Unplug from outlet when not in
use and before conducting maintenance.
WARNING: To reduce
the risk of fire, electric shock,
or injury:
■ Do not modify the polarized plug to fit a
non-polarized outlet or extension cord.
■ Do not leave vacuum cleaner unattended
when it is plugged in.
■ Unplug from outlet when not in use and
before servicing.
■ Unplug before attaching TurboBrush.
■ Do not use outdoors or on wet surfaces.
■Do not allow children to operate vacuum
cleaner or use as a toy.
■ Close attention is necessary when used by or
near children.
■ Do not use for any purpose other than described
in this User’s Guide.
■ Use only manufacturer’s recommended
■
■
■
■
■
■
attachments.
Do not use with damaged cord or plug.
If appliance is not working as it should,
has been dropped, damaged, left outdoors,
or dropped into water, have it repaired at an
authorized service center.
Do not pull or carry by cord, use cord as a
handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run
appliance over cord. Keep cord away from
heated surfaces.
Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
Do not handle vacuum cleaner or plug with
wet hands.
Do not put any object into openings.
Do not use with any opening blocked; keep
openings free of dust, lint, hair, and anything
that may reduce air flow.
■ Keep hair, loose clothing, fingers, and all parts
of body away from openings and moving parts.
■ Turn off all controls before plugging or
unplugging vacuum cleaner.
■ Use extra care when cleaning stairs.
■ Do not pick up flammable materials (lighter
fluid, gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapors.
■ Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, etc.).
■ Do not use vacuum cleaner in an enclosed
space filled with vapors given off by oil base
paint, paint thinner, some moth proofing
substances, flammable dust, or other
explosive or toxic vapors.
■ Do not pick up hard or sharp objects such as
glass, nails, screws, coins, etc.
■ Do not pick up anything that is burning
or smoking, such as cigarettes, matches, or
hot ashes.
■ Do not use without filters in place.
■ Use only on dry, indoor surfaces.
■ Keep appliance on a level surface.
■ Do not carry the vacuum cleaner while it
is running.
WARNING: The Power Cord on this product
contains lead, a chemical known to the State of
California to cause birth defects or other
reproductive harm. WASH HANDS
AFTER HANDLING.
SAVE THESE
INSTRUCTIONS FOR
FUTURE USE
THIS APPLIANCE HAS
A POLARIZED PLUG.
To reduce the risk of electric shock, this appliance has
a polarized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician
to install a proper outlet. Do not change the plug in
any way.
This model is for household use only.
1.
3
Handle
Cord Clip
Hose Clip
Stretch Hose
Carrying
Handle
Quick Release™
Cord Wrap
Crevice Tool
Power Cord
Twist 'n
Snap™ Hose
Quick Reach®
Handle
Upper Tank Knob
Extension Wand
Hose Wand
Hose
Wand Base
Dusting Brush/
Upholstery Tool
TurboBrush®
(Select Models Only)
Clean Carpet Sensor
(Select Models Only)
Power Switch
Clean Filter Indicator
(Select Models Only)
Louvers
Upper Tank
Frame and Filter
(Inside Louvers)
Upper Tank
Handle Release
Pedal
Dirt Container
Dust Chambers
with Screens
Pre-Motor Filter
Headlight
Post-Motor
Filter
Lock ’n Seal®
Lever
Height
Adjustment
Knob
Wide Window
Foot
Window
Wide Cleaning
Path Foot
1.
4
Furniture
Protection
Guard
Furniture Protection
Guard
caution:
Do not plug in your vacuum
cleaner until you are familiar
with all instructions and
operating procedures.
How To Use This Guide
This User’s Guide has been designed to help you
get the most satisfaction from your BISSELL vacuum.
You’ll find assembly and operating instructions,
safety precautions, as well as maintenance and
troubleshooting instructions. Please read this Guide
thoroughly before assembling your vacuum cleaner.
Pay particular attention to the product diagram,
assembly instructions, and part names. Locate and
organize all parts before assembly. Familiarize
yourself with the parts and where they fit. Following
this User’s Guide will greatly enhance your ability
to get the most performance from your BISSELL
vacuum for many years.
W
arning:
Plastic film can
be dangerous. To avoid
danger of suffocation,
keep away from babies
and children.
How To Put It Together
The only tool you’ll need to assemble your vacuum
cleaner is a screwdriver.
Attach Handle To Vacuum
1. Locate the vacuum Handle and remove the screw
packet taped to the base of the Handle.
2. Stand the vacuum upright and slide the base of
the Handle firmly into the grooves at the top of the
vacuum body.
3. Check to be sure the Handle is fitted to the vacuum
body. If there is a gap in front, continue to push firmly
until the Handle is flush.
4. Insert the screw provided from the screw packet into
the existing hole. Tighten securely with a screwdriver.
1.
5
Attach Vacuum Hose and Tools
1. Line up the tabs on the base of the Twist ‘n Snap
Hose with the corresponding notches on the hose
collar as shown.
2. Turn the Twist ‘n Snap Hose to the right to lock the
hose into place.
3. Grasping the Quick Reach Handle, slide the end of
the Hose Wand onto the Hose Wand Base. Snap the
Hose into the Hose Clip.
NOTE: The Powerfoot will not operate
effectively unless the Hose Wand is
firmly attached.
4. Slide the Extension Wand and the Crevice Tool
together into the storage clip as shown.
5. Slide the Dusting Brush/Upholstery Tool into the storage clip
as shown.
6. Attach the TurboBrush by aligning the small holes near
the brush roll with the tabs at the bottom of TurboBrush
housing. Snap TurboBrush into place as shown.
Select Models Only
NOTICE:
The Floor Brush will continue to rotate
while you use your vacuum for above
floor cleaning. To prevent carpet
damage, do not lean on the vacuum or
let the Powerfoot tilt forward.
caution
:
Before using your vacuum,
make sure that the Dirt
Container and Upper Tank are
in locked position and that all
filters (UpperTank, Pre-Motor
and Post-Motor) are in place.
Do not operate your vacuum
without these filters.
1.
6
How To Use Your Vacuum
Handle Positions
1
Press the Handle Release Pedal with your foot to place
your vacuum into one of three cleaning positions.
2
1. Upright- For storage and above floor cleaning with tools.
2. Normal Cleaning- Press Handle Release Pedal once. Use
for most household floor cleaning tasks.
3
3. Low Cleaning- With the vacuum in normal cleaning
position, press Handle Release Pedal again. Use for
reaching under low furniture such as tables, chairs
or beds.
Height Adjustment
T he Powerfoot/Rotating Floor Brush on your vacuum
can be adjusted to clean several floor surfaces.
NOTE: For optimal cleaning performance,
adjust to the lowest practical setting. If your
cleaner is difficult to push, adjust to the
next higher setting.
1. Place Handle in Upright Position.
2. Turn Height Adjustment knob to desired setting.
Lowest Setting
Medium Settings
Highest Setting
For bare floors.
For short and medium
pile carpets.
For plush pile carpet.
Tip:
Tip:
Before cleaning under
low furniture, check
area first for objects
that might harm the
unit or block the
Vacuum Hose.
Your vacuum features
a Quick-Release
Cord Wrap. To
remove the Power
Cord quickly and
easily, rotate the
Upper Cord Wrap
towards floor, and
slip Power Cord from
Upper and Lower
Cord Wraps.
3. Place the Handle in the normal cleaning position and the
Powerfoot will adjust to the setting chosen.
NOTE: You may also adjust the setting while
in the normal cleaning position.
Transporting Cleaner
1. To move your cleaner from room to room, put the
Handle in the upright position, tilt the cleaner back on
its rear wheels and push forward.
Carrying
Handle
2. The cleaner can also be moved by using the
Carrying Handle.
1.
7
Clean Carpet Sensor
Select Models Only
The Clean Carpet Sensor detects dirt being picked up
while the vacuum is in use. When the vacuum is picking
up dirt, the red light will come on. Occasionally, the lights
may alternate quickly back and forth if the area is only
lightly soiled or the dirt is spread out. For the best
cleaning, continue to vacuum until the green light
remains constantly illuminated.
Clean Filter Indicator
Select Models Only
The Clean Filter Indicator tells you when airflow in
the vacuum is reduced due to dirty filters or a clog
in the hose. The Clean Filter Indicator will remain
green until the airflow is reduced. At that time, it
begins to change to red. When it is fully red, the
airflow is significantly reduced or blocked. Follow
the steps on page 11 to clean your filters. All filters
in the vacuum should be cleaned or replaced when
the Clean Filter Indicator turns red.
If the indicator remains red after all filters have been
cleaned, follow the steps on page 13 to check for
and clear clogs.
1.
8
NOTICE:
While vacuuming, certain carpets
and low humidity conditions may
generate small static discharges.
The discharges are entirely
harmless and are not associated
in any way with the main
power supply.
Special On-Board Tools
Your vacuum is not only a powerful carpet and rug
vacuum cleaner, it’s also a versatile above floor vacuum cleaner when you select one of the special tools.
1. Raise Handle to Upright Position.
2. Grasp the Quick Reach Handle and lift Hose Wand to
separate from suction intake opening.
3. Attach tools by firmly pushing onto Vacuum Hose or
Extension Wand.
Dusting Brush/Upholstery Tool: Two types of cleaning
tools in one attachment.
•Use the Dusting Brush to dust furniture, blinds, books,
lamps, shelves and baseboards.
•Slide the brush off to use the Upholstery Tool on
cushions, draperies and fabrics.
Crevice Tool: Use in tight narrow spaces.
Extension Wand: Use with desired attachment for a
longer reach.
TurboBrush (Select Models): Use rotating brush action
for small areas such as stairs and upholstery.
Note: Press gently when using the
TurboBrush to gain maximum cleaning. Too
much pressure will cause the brush to
stop rotating.
Stair Cleaning Tool (Select Models): Use for stairs, area
rugs, and other small carpeted areas. This tool can also be
used for bare floors.
All items may not be included with your model. More
tools are available; to order please refer to page 15.
Power Cord Storage
When you are done using your vacuum, return it to
the Upright position and store the Power Cord.
1. Turn vacuum cleaner off.
2. Unplug Power Cord by grasping the polarized plug (NOT
the cord) and disconnect from outlet.
3. Loop Power Cord around Cord Wraps on side of
vacuum cleaner.
4. Clip molded plug to Power Cord to secure.
Tip:
Hair, string and small objects can block
the Vacuum Hose or Tools. Check them
occasionally for obstructions.
NOTICE:
The Floor Brush will continue
to rotate while you use your
vacuum for above floor cleaning.
To prevent carpet damage, do
not lean on the vacuum or let the
Powerfoot tilt forward.
CAUTION:
The Rotating Floor Brush
continues to rotate while tools
are in use. To reduce the risk
of injury from moving parts,
always move the cleaner with
the Carrying Handle at the
back of the cleaner. Always
place vacuum cleaner on floor
with Handle in Upright position
when using tools. Never place
your fingers under the cleaner
when it is running. Never place
Powerfoot on furniture or
uneven surfaces. Do not place
vacuum cleaner close enough
to objects to pull them into
rotating brush.
1.
9
How To Maintain Your Vacuum
W
ARNING:
To reduce the risk of
To maximize your cleaning performance and extend the
life of your vacuum, it is very important that you empty
your dirt container and check and clean your filters
frequently. Perform the following maintenance steps:
electric shock, turn
Power Switch OFF and
disconnect polarized
plug from electrical outlet
before performing
maintenance or
troubleshooting checks.
1. Empty the Dirt Container when the dirt reaches the
“Full” line.
2. Check the Upper Tank and Pre-Motor Filters at least once a
month and clean or replace as needed.
Tip:
3. Clean or replace the Post-Motor Filter every three to six months.
Note: More frequent filter cleaning may be
necessary if you are vacuuming new carpet,
fine dust, or have allergy concerns. Follow the
instructions on the following pages to perform
these simple maintenance steps.
For maximum cleaning
performance, check
and clean or replace all
filters as suggested.
Empty Dirt Container
The Dirt Container needs to be emptied when the dirt
reaches the “Full” line on the Container.
1. Unplug cleaner from electrical outlet.
2. Slide the Lock ‘n Seal Lever to the "Unlock" position.
Full Line
Lock Position
Unlock
Position
3. Grasp handle and pull the Dirt Container straight out to
remove from vacuum.
4. Empty dirt into garbage container. The Screens may also be
removed from the side Dust Chambers when you empty or
clean the Dirt Container. The Screens are made to fit each
Dust Chamber. If they do not slide down completely, try in
the opposite Dust Chamber. The Screens will also not fit if
there is debris in the track.
5. Put the Dirt Container back in the vacuum and slide the
lever to the "Lock" position.
Note: The Dirt Container and Screens may be
washed in warm water with a mild detergent.
Make sure it is completely dry before using again.
Clean Carpet Sensor
To maintain the effectiveness of the Clean Carpet
Sensor, a quarterly cleaning of the internal sensor
lens is recommended. To clean the sensor lens,
detach the Twist ‘n Snap Hose and gently wipe the
clear lens area using a lightly dampened soft cloth.
Allow enough time for the lens to dry thoroughly
before reattaching the Twist ‘n Snap Hose and using
the vacuum.
10
1.
Screen
Cleaning The Upper Tank & Filter
1. Unplug the cleaner from electrical outlet.
2. The Upper Tank Filter can be reached by removing the Dirt
Container, reaching underneath the Upper Tank and turning
the rim of the Filter Frame to unlock. Pull straight down to
remove. Brush the dirt off the Louvers and Upper Tank Filter.
3. The foam Upper Tank Filter may be removed and hand
washed in cold water with mild detergent. Rinse well then
air dry thoroughly before replacing.
4. The Upper Tank and Louvers may also be wiped clean with
a damp cloth.
Note: For easier access, the entire Upper Tank
may be removed by turning the knob on the
back of the cleaner to unlock and pulling the
entire tank straight out.
W
ARNING:
Do Not operate cleaner
Cleaning The Pre-Motor and Post-Motor Filter
1. Unplug the cleaner from electrical outlet.
with damp or wet
filters or without all
filters in place.
2. The Pre-Motor Filter protects the motor from dirt particles.
It is located in the slide out tray underneath the Dirt
Container. If the filter becomes dirty, pull out the tray, lift
out the filter and clean.
3. The Post-Motor Filter assists in the filtration process to
return clean air to the room. It is located behind the door on
the side of the cleaner. If the filter becomes dirty, open the
door, remove the filter and clean.
Note: Select models come with a white,
pleated post-motor filter that is not washable
and must be replaced.
Pre-Motor
Filter
4. The standard filters may be hand washed in cold water
with mild detergent. Rinse well and air dry thoroughly
before replacing.
Check Rotating Floor Brush and Drive Belt
You should check your vacuum cleaner’s Rotating
Floor Brush and Drive Belt regularly for wear or
damage. You should also clean the brush and brush
ends of strings, hair, and carpet fibers. These can
wrap around the brush and hamper its ability to
effectively clean your carpet. Also remove any debris
that has accumulated under the brush cover.
1. Unplug cleaner from electrical outlet.
Post-Motor
Filter
W
ARNING:
To reduce the risk of injury
from moving parts, turn
off vacuum cleaner and
disconnect Power Plug
from electrical outlet.
4
2. Place handle in Low position and turn vacuum cleaner over
so bottom side is up.
3. Lift Tab 1 and release the three latches in order 2-4
marked. Lift the Brush Cover off.
11
1.
Check Rotating Floor Brush and Drive Belt Continued
4. Grasp Rotating Floor Brush at both ends and lift.
5. Clean strings, hair and other debris from Rotating Floor
Brush, paying particular attention to brush ends.
Motor Pulley
6. Clean strings, hair and other debris from Motor Pulley and
Drive Belt areas.
7. Check Drive Belt carefully for wear, cuts or stressed areas.
8. Check Air Passageway for obstructions. Remove debris
from this area.
Replace Drive Belt
1. Unplug cleaner from electrical outlet.
2. With Rotating Floor Brush removed from vacuum cleaner
(Steps 1-4 of check Rotating Floor Brush and Drive Belt),
grasp old Drive Belt and remove from Motor Pulley.
Discard old Drive Belt.
3. Place new Drive Belt over Motor Pulley and stretch other end
over Rotating Floor Brush in the space between the bristles.
4. Place ends of Rotating Floor Brush down into slots on
sides as shown.
5. Turn Rotating Floor Brush by hand several times in the
direction of Motor Pulley. If properly installed, Drive Belt
will center itself on Rotating Brush crown.
6. Reposition Brush Cover and screw or snap back into place.
Check to be sure all screws or latches are secure.
Replace Lightbulb
1. Unplug cleaner from electrical outlet.
2. Using a screwdriver, remove the two screws as shown
and lift off the lens.
3. Remove the bulb from the socket by grasping bulb and
pulling straight out. Install the new bulb by pushing it
gently into the socket until the bulb snaps into place.
4. Reposition lens and secure with the two screws.
Maintaining TurboBrush
Select Models Only
The TurboBrush should be checked regularly for clogs
or debris wrapping around the brush roll.
1. Unplug vacuum from electrical outlet.
2. If a clog is present or debris is visible, unscrew the two
screws on the back of the TurboBrush to remove the
faceplate and clear any obstructions.
3. To clean debris from the brush roll, remove the screw
12
1.
located by the brush roll with a Phillips head screwdriver.
Lift the belt cover. Remove the brush roll from the drive
belt and clean debris.
Air Passageway
Maintaining TurboBrush Continued
4. Reposition the drive belt on the brush roll. Place ends
of brush roll in slots on sides as shown. Reposition belt
cover and secure with one screw. Reposition faceplate
and secure with two screws.
Clearing Clogs
Low suction or poor pickup may be due to a clog in
the vacuum cleaner. If you notice a change in the
sound of the motor or a reduction in the spinning
action, check for clogs.
1. Unplug cleaner from electrical outlet.
2. Empty Dirt Container.
3. Check Upper Tank for build up or clogs.
4. Remove the Upper Tank and check the suction inlet for a clog.
Suction
Inlet
5. Grasp the Quick Reach Handle and lift Hose Wand to separate
from the suction opening. Check for a clog in the Base, the
Wand or the Hose.
6. Release the Twist 'n Snap Hose from the vacuum by turning
to the left. Straighten the hose and unclog with a long,
narrow object.
Hose Wand
Base
7. If the clog persists, follow the instructions for Checking
the Rotating Floor Brush on pages 11-12 and inspect the
Air Passageway for obstructions.
Air Passageway
BISSELL Consumer Services
For information about repairs or replacement parts, or questions about your
warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
8 a.m. — 10 p.m. ET
Saturday
9 a.m. — 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It is your warranty.
13
1.
Troubleshooting
W
ARNING:
To reduce the risk of injury from moving
Vacuum cleaner won’t run
Possible Causes
parts and/ or electrical shock, turn Power
Switch OFF and disconnect polarized plug
from electrical outlet before performing
troubleshooting checks.
Remedies
1 Power cord not plugged in1 Check electrical plug
2 Blown fuse/tripped breaker2 Check/Replace fuse or reset breaker
Vacuum cleaner or Tools won’t pick up dirt
Possible Causes
Remedies
1 Incorrect Height Adjustment1
2 Hose not attached to suction opening2
3 Twist ‘n Snap Hose not securely attached3
4 Crack or hole in Hose4
5 Broken or worn Drive Belt5
6 Rotating Floor Brush bristles worn6
7 Rotating Floor Brush jammed7
8 Clog in vacuum8
9 Dirt Container full9
10 Dirt Container or Upper Tank not installed properly10
11 Filters are dirty11
12 TurboBrush is clogged or debris is wrapped 12
around the Brush Roll
Vacuum cleaner is difficult to push
Possible Causes
Adjust Powerfoot to correct height
Firmly push Hose Wand into the suction opening
Make sure Twist ‘n Snap Hose is snapped into
locked position
Check Hose and replace if needed
Replace Drive Belt, see page 12
Replace brush
Remove brush and clean debris from brush ends
Clear clog, see page 13
Empty Dirt Container
Position correctly and lock in place
Check and clean Upper Tank,
Pre-Motor and Post-Motor Filters
Maintaining TurboBrush, see pages 12-13
Remedies
1 Incorrect Height Adjustment1 Adjust Powerfoot to correct height setting
Visible dirt escaping from cleaner
Possible Causes
Remedies
1 Dirt Container full 1
2 Filters missing or installed incorrectly 2
3 Dirt Container installed incorrectly3
Empty Dirt Container
Check Upper Tank, Pre-Motor and Post-Motor
Filters for correct installation
Pull out and re-insert Dirt Container correctly
Clean Carpet Sensor not functioning properly
Possible Causes
Remedies
1 Clean Carpet Sensor Lens is Dirty 1 Clean Internal Sensor Lens, see page 10
Clog in Suction Intake Area 2 Clear clog, see page 13
14
1. 2
Replacement Parts – BISSELL Vacuum
You may purchase replacement parts from your retailer, by calling BISSELL Consumer
Services or by visiting our website. To locate a retailer near you, or to place an order using
VISA, MasterCard, Discover or American Express, call:
BISSELL Consumer Services
1-800-237-7691
Or visit our Website - www.bissell.com
Item Part No.
Part Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32074
Style 7/9/10 Drive Belt (2-Pack)
203-1297
Standard Headlight Bulb
203-1063Crevice Tool
203-1228Dusting Brush/Upholstery Tool
203-6732TurboBrush (Select Models Only)- Lime
203-6730
TurboBrush (Select Models Only)- Sonic Yellow
203-6624
Stair Cleaning Tool (Select Models Only)
203-1084Extension Wand
203-2035
Wire Reinforced Twist ‘n Snap Vacuum Hose Clear
203-6726Wide Window Foot Brush Roll - Lime
203-6729Wide Window Foot Brush Roll - Sonic Yellow
203-6756Wide Window Foot Brush Roll - Taupe
203-1195
Wide Cleaning Path Foot Brush Roll
3093
Style 7/8 Upper Tank Filter and Pre-Motor Filter Set
3099
Style 7 Washable Post-Motor Filter Set (2 pack)
32076
Style 7 Post-Motor Filter
1
2
3
7
8
9
15
16
4
10/11/12/13
5/6
14
15
1.
Warranty
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to
state. If you need additional instruction regarding this warranty or have questions regarding what it may cover,
please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare,
Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of
charge from the date of purchase by the original purchaser, for one year any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not
apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused
by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is
not covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your
warranty, contact BISSELL Consumer Services.
Website or E-mail:
www.bissell.com
Use the “Customer Services” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER
ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION
OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION
FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you.
16
1.
©2013 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in Korea
Part Number 110-4034
Rev 09/13
Visit our website at:
www.bissell.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement