18659rg

18659rg
PT6300 Series
3 Amp Adjustable Positive Step-down
Integrated Switching Regulators
SLTS031B
(Revised 9/30/2000)
•
•
•
•
•
•
•
90% Efficiency
Adjustable Output Voltage
Internal Short Circuit Protection
Over-Temperature Protection
On/Off Control (Ground Off)
Small SIP Footprint
Wide Input Range
The PT6300 Series is a line of
High-Performance 3 Amp, 12-Pin SIP
(Single In-line Package) Integrated
Pin-Out Information
Pin
1
Standard Application
VOADJ
12
VIN
2,3,4
PT6300
VOUT
9,10,11
1
5,6,7,8
C1
C2
INH
+
Q1
COM
COM
C1 = Optional 1µF ceramic
C2 = Required 100µF electrolytic
Q1 = NFET
(1)
Specifications
Function
Inhibit
(30V max)
2
3
Vin
Vin
4
5
Vin
GND
6
7
GND
GND
8
9
GND
Vout
10
11
Vout
Vout
12
Vout Adj (5)
Switching Regulators (ISRs) designed
to meet the on-board power conversion
needs of battery powered or other
equipment requiring high efficiency and
small size. This high performance ISR
family offers a unique combination of
features combining 90% typical efficiency with open-collector on/off
control and adjustable output voltage.
Quiescent current in the shutdown
mode is typically less than 100µA.
Ordering Information
PT Series Suffix (PT1234X)
PT6302¨
PT6303¨
PT6304¨
PT6314¨
Case/Pin
Configuration
= +5 Volts
= +3.3 Volts
= +12 Volts
= +1.5Volts
N
A
C
Vertical Through-Hole
Horizontal Through-Hole
Horizontal Surface Mount
Pkg Style 200
PT6300 SERIES
Characteristics
(Ta=25°C unless noted)
Symbols
Output Current
Short Circuit Current
Conditions
Min
Io
Isc
Over Vin range
Vin = Vo + 5V
0.1
—
Typ
Max
Units
—
5.0
3.0
—
A
Apk
Input Voltage Range
(Note: inhibit function cannot
be used above 30V.)
Vin
0.1 ≤ Io ≤ 3.0 A
16
9
9
9.0
—
—
—
—
30/38 (3)
30/38 (3)
26
17
V
Output Voltage Tolerance
∆Vo
Over Vin Range, Io = 3.0 A
Ta = 0°C to +60°C
—
±1.0
±2.0
%Vo
Line Regulation
Load Regulation
Regline
Regload
Over Vin range
0.1 ≤ Io ≤ 3.0 A
—
—
±0.25
±0.25
±0.5
±0.5
%Vo
%Vo
Vo Ripple/Noise
Transient Response
with Co = 100µF
Efficiency
Vn
ttr
Vos
η
—
—
—
—
—
—
—
600
400
350
±2
100
5.0
91
89
84
72
750
500
450
—
200
—
—
—
—
—
900
600
550
%Vo
µSec
%Vo
Vo = 12V
Vo = 5.0V
Vo = 3.3V
Vo = 1.5V
(2)
Switching Frequency
ƒo
Vin = Vin min, Io = 3.0 A
50% load change
Vo over/undershoot
Vin=16V, Io = 0.5 A,
Vin=9V, Io = 0.5 A,
Vin=9V, Io = 0.5 A,
Vin=9V, Io =0.5A,
Over Vin and Io ranges,
Shutdown Current
Quiescent Current
Isc
Inl
Vin = 15V
Io = 0A, Vin =10V
—
—
100
10
—
—
µA
mA
Absolute Maximum
Operating Temperature Range
Ta
Over Vin range
-40
—
+85 (4)
°C
Thermal Resistance
θja
Free Air Convection (40-60LFM)
—
30
—
°C/W
Storage Temperature
Ts
—
-40
—
+125
°C
Mechanical Shock
Per Mil-STD-883D, Method 2002.3, 1 msec,
Half Sine, mounted to a fixture
—
500
—
G’s
Mechanical Vibration
Per Mil-STD-883D, Method 2007.2,
20-2000 Hz,Soldered in a PC board
—
—
10
—
G’s
—
6.5
—
grams
Weight
Notes: (1)
(2)
(3)
(4)
(5)
—
Vo = 12V
Vo = 5.0V
Vo = 3.3V
Vo = 1.5V
Vo = 12V
Vo = 3.3V/5V
Vo = 1.5V
The PT6300 Series requires a 100µF electrolytic or tantalum output capacitor for proper operation in all applications.
The ISR will operate to no load with reduced specifications.
Input voltage cannot exceed 30V when the inhibit function is used.
See Thermal Derating charts.
Consult the related application note for guidance on adjusting the output voltage.
For technical support and more information, see inside back cover or visit www.ti.com/powertrends
%
kHz
Typical Characteristics
PT6300 Series
3 Amp Adjustable Positive Step-down
Integrated Switching Regulators
PT6302, 5.0 VDC
(See Note A)
Efficiency vs Output Current
Efficiency vs Output Current
100
Vin
80
9.0V
12.0V
15.0V
20.0V
26.0V
70
60
Efficiency - %
90
Efficiency - %
PT6304, 12.0 VDC
(See Note A)
(See Note A)
Efficiency vs Output Current
100
100
90
90
Vin
80
9.0V
12.0V
15.0V
24.0V
30.0V
38.0V
70
60
Efficiency - %
PT6303, 3.3 VDC
Vin
80
16.0V
20.0V
70
24.0V
30.0V
38.0V
60
50
50
50
40
0
0.5
1
1.5
2
2.5
3
40
40
0
0.5
1
Iout-(Amps)
2
2.5
0
3
180
140
160
100
26.0V
20.0V
15.0V
12.0V
9.0V
80
60
Ripple-(mV)
Vin
80
20
1.5
2
2.5
38.0V
30.0V
24.0V
20.0V
150
16.0V
100
0
0
1
Vin
200
50
0
0
0.5
1
1.5
2
2.5
3
0
0.5
1
1.5
2
2.5
3
3
Iout-(Amps)
Iout-(Amps)
Thermal Derating (Ta)
3
250
60
20
2.5
300
38.0V
30.0V
24.0V
15.0V
12.0V
9.0V
100
40
2
Vin
120
40
1.5
350
140
V
120
0.5
1
Ripple vs Output Current
Ripple vs Output Current
160
0
0.5
Iout-(Amps)
Ripple-(mV)
Ripple vs Output Current
Ripple-(mV)
1.5
Iout-(Amps)
Thermal Derating (Ta)
(See Note B)
60°C
3
Iout-(Amps)
Thermal Derating (Ta)
(See Note B)
3
(See Note B)
3
50°C
70°C
40°C
60°C
2.5
2.5
2.5
50°C
1.5
1
2
Iout-(Amps)
85°C
Iout-(Amps)
Iout-(Amps)
60°C
70°C
2
2
85°C
1.5
1
70°C
1.5
1
0.5
0.5
0.5
0
0
0
9
9
11
13
15
17
19
21
23
25
13
17
21
Vin-(Volts)
29
33
16
37
19
22
25
Vin-(Volts)
Power Dissipation vs Output Current
3
1
37
4
3.5
38.0V
30.0V
24.0V
15.0V
12.0V
9.0V
2
1.5
PD-(Watts)
Vin
2.5
PD-(Watts)
26.0V
20.0V
15.0V
12.0V
9.0V
1.5
34
4.5
3
Vin
2
31
Power Dissipation vs Output Current
3.5
2.5
28
Vin-(Volts)
Power Dissipation vs Output Current
3.5
PD-(Watts)
25
27
Vin
3
38.0V
30.0V
24.0V
20.0V
16.0V
2.5
2
1.5
1
1
0.5
0.5
0.5
0
0
0
0.5
1
1.5
2
2.5
3
0
0.5
1
1.5
2
2.5
3
0
0
Iout-(Amps)
Iout-(Amps)
0.5
1
1.5
2
2.5
3
Iout-(Amps)
Note A: Characteristic data listed in the above graphs has been developed from actual products tested at 25°C. This data is considered typical data for the ISR
Note B: Thermal derating graphs are developed in free air convection cooling of 40-60 LFM. (See Thermal Application note.)
For technical support and more information, see inside back cover or visit www.ti.com/powertrends
Application Notes
PT6100/6210/6300 Series
Adjusting the Output Voltage of Power Trends’
Wide Input Range Bus ISRs
The output voltage of the Power Trends’ Wide Input
Range Series ISRs may be adjusted higher or lower than
the factory trimmed pre-set voltage with the addition of a
single external resistor. Table 1 accordingly gives the
allowable adjustment range for each model for either
series as Va (min) and Va (max).
Adjust Up:
An increase in the output voltage is obtained by
adding a resistor R2, between pin 12 (Vo adjust) and pins 5-8
(GND).
Adjust Down: Add a resistor (R1), between pin 12 (Vo adjust)
and pins 9-11(Vout).
Notes:
1. Use only a single 1% resistor in either the (R1) or R2
location. Place the resistor as close to the ISR as possible.
2. Never connect capacitors from Vo adjust to either GND
or Vout. Any capacitance added to the Vo adjust pin will
affect the stability of the ISR.
3. Adjustments to the output voltage may place additional
limits on the maximum and minimum input voltage for
the part. The revised maximum and minimum input
voltage limits must comply with the following
requirements. The limits are model dependant.
PT6216/PT6314:
Vin (max) = (10 x Va)V or 17V, whichever is less.
Vin (min) = 9.0V
Figure 1
All other models:
2,3,4
Vin
PT6100/6200/6300
Vin
Vo
GND
9,10,11
Vo
5,6,7,8
12
(R1)
Adj Down
C1
1µF Ceramic
(Optional)
Vin (max) = (8 x Va)V or as specified.
Vin (min) = (Va + 4)V or 9V, whichever is greater.
Vo(adj)
C2
100µF
(Req'd)
+
R2
Adjust
Up
COM
COM
The values of (R1) [adjust down], and R2 [adjust up], can
also be calculated using the following formulas. Refer to
Figure 1 and Table 2 for both the placement and value of the
required resistor; either (R1) or R2 as appropriate.
(R1)
=
Ro (Va – 1.25)
Vo – Va
kΩ
R2
=
1.25 Ro
Va – Vo
kΩ
Where: Vo = Original output voltage
Va = Adjusted output voltage
Ro = The resistance value fromTable 1
Table 1
ISR ADJUSTMENT RANGE AND FORMULA PARAMETERS
1Adc Rated
2Adc Rated
3Adc Rated
PT6216
PT6314
PT6102
PT6213
PT6303
PT6101
PT6212
PT6302
PT6103
PT6214
PT6304
12.0
Vo (nom)
Va (min)
1.5
3.3
5.0
5.0
1.3
1.8
1.88
2.18
2.43
Va (max)
Ω)
Ro (kΩ
1.9
6.07
11.25
8.5
22.12
8.25
66.5
150.0
90.9
243.0
For technical support and more information, see inside back cover or visit www.ti.com/powertrends
Application Notes continued
PT6100/6210/6300 Series
Table 2
ISR ADJUSTMENT RESISTOR VALUES
1Adc Rated
2Adc Rated
3Adc Rated
Vo (nom)
Va (req.d)
PT6216
PT6314
1.5
PT6102
PT6213
PT6303
3.3
ISR ADJUSTMENT RESISTOR VALUES (Cont)
PT6101
5.0
PT6212
PT6302
5.0
PT6103
PT6214
PT6304
12.0
1Adc Rated
2Adc Rated
3Adc Rated
Vo (nom)
Va (req.d)
PT6101
5.0
PT6212
PT6302
5.0
PT6103
PT6214
PT6304
12.0
1.3
(2.1kΩ)
6.2
156.0kΩ
94.7kΩ
(207.0)kΩ
1.4
(12.4kΩ)
6.4
134.0kΩ
81.2kΩ
(223.0)kΩ
6.6
117.0kΩ
71.0kΩ
(241.0)kΩ
1.5
1.6
103.0kΩ
6.8
104.0kΩ
63.1kΩ
(259.0)kΩ
1.7
51.6kΩ
7.0
93.8kΩ
56.8kΩ
(279.0)kΩ
1.8
34.4kΩ
(24.4)kΩ
7.2
85.2kΩ
51.6kΩ
(301.0)kΩ
1.9
25.8kΩ
(30.9)kΩ
(31.5)kΩ
7.4
78.1kΩ
47.3kΩ
(325.0)kΩ
2.0
(38.4)kΩ
(37.5)kΩ
7.6
72.1kΩ
43.7kΩ
(351.0)kΩ
2.1
(47.1)kΩ
(44.0)kΩ
7.8
67.0kΩ
40.6kΩ
(379.0)kΩ
2.2
(57.4)kΩ
(50.9)kΩ
(30.8)kΩ
8.0
62.5kΩ
37.9kΩ
(410.0)kΩ
2.3
(69.8)kΩ
(58.3)kΩ
(35.4)kΩ
8.2
58.6kΩ
35.5kΩ
(444.0)kΩ
2.4
(85.0)kΩ
(66.3)kΩ
(40.2)kΩ
8.4
55.1kΩ
33.4kΩ
(483.0)kΩ
2.5
(104.0)kΩ
(75.0)kΩ
(45.5)kΩ
(32.0)kΩ
8.6
52.1kΩ
(525.0)kΩ
2.6
(128.0)kΩ
(84.4)kΩ
(51.1)kΩ
(34.9)kΩ
8.8
49.3kΩ
(573.0)kΩ
2.7
(161.0)kΩ
(94.6)kΩ
(57.3)kΩ
(37.9)kΩ
9.0
46.9kΩ
(628.0)kΩ
2.8
(206.0)kΩ
(106.0)kΩ
(64.0)kΩ
(40.9)kΩ
9.5
41.7kΩ
(802.0)kΩ
2.9
(274.0kΩ
(118.0)kΩ
(71.4)kΩ
(44.1)kΩ
10.0
37.5kΩ
(1060.0)kΩ
3.0
(388.0)kΩ
(131.0)kΩ
(79.5)kΩ
(47.3)kΩ
10.5
34.1kΩ
(1500.0)kΩ
3.1
(615.0)kΩ
(146.0)kΩ
(88.5)kΩ
(50.5)kΩ
11.0
31.3kΩ
3.2
(1300.0)kΩ
(163.0)kΩ
(98.5)kΩ
(53.8)kΩ
11.5
3.3
(181.0)kΩ
(110.0)kΩ
(57.3)kΩ
3.4
831.0kΩ
(202.0)kΩ
(122.0)kΩ
(60.8)kΩ
12.5
608.0kΩ
3.5
416.0kΩ
(225.0)kΩ
(136.0)kΩ
(64.3)kΩ
13.0
304.0kΩ
3.6
227.0kΩ
(252.0)kΩ
(153.0)kΩ
(68.0)kΩ
13.5
203.0kΩ
3.7
208.0kΩ
(283.0)kΩ
(171.0)kΩ
(71.7)kΩ
14.0
152.0kΩ
3.8
166.0kΩ
(319.0)kΩ
(193.0)kΩ
(75.6)kΩ
14.5
122.0kΩ
3.9
139.0kΩ
(361.0)kΩ
(219.0)kΩ
(79.5)kΩ
15.0
101.0kΩ
4.0
119.0kΩ
(413.0)kΩ
(250.0)kΩ
(83.5)kΩ
15.5
86.8kΩ
4.1
104.0kΩ
(475.0)kΩ
(288.0)kΩ
(87.7)kΩ
16.0
75.9kΩ
4.2
92.4kΩ
(533.0)kΩ
(335.0)kΩ
(91.9)kΩ
16.5
67.5kΩ
4.3
83.1kΩ
(654.0)kΩ
(396.0)kΩ
(96.3)kΩ
17.0
60.8kΩ
4.4
75.6kΩ
(788.0)kΩ
(477.0)kΩ
(101.0)kΩ
17.5
55.2kΩ
4.5
69.3kΩ
(975.0)kΩ
(591.0)kΩ
(105.0)kΩ
18.0
50.6kΩ
4.6
63.9kΩ
(1260.0)kΩ
(761.0)kΩ
(110.0)kΩ
18.5
46.7kΩ
4.7
59.4kΩ
(1730.0)kΩ
(1050.0)kΩ
(115.0)kΩ
19.0
43.4kΩ
4.8
55.4kΩ
(1610.0)kΩ
(120.0)kΩ
19.5
40.5kΩ
4.9
52.0kΩ
(125.0)kΩ
20.0
38.0kΩ
5.0
48.9kΩ
(130.0)kΩ
20.5
35.7kΩ
5.1
46.2kΩ
1880.0kΩ
1140.0kΩ
(136.0)kΩ
21.5
33.8kΩ
5.2
43.8kΩ
937.0kΩ
568.0kΩ
(141.0)kΩ
21.5
32.0kΩ
5.3
41.6kΩ
625.0kΩ
379.0kΩ
(147.0)kΩ
22.0
30.4kΩ
5.4
39.6kΩ
469.0kΩ
284.0kΩ
(153.0)kΩ
5.5
37.8kΩ
375.0kΩ
227.0kΩ
(159.0)kΩ
5.6
36.1kΩ
313.0kΩ
189.0kΩ
(165.0)kΩ
5.7
34.6kΩ
268.0kΩ
162.0kΩ
(172.0)kΩ
5.8
33.3kΩ
234.0kΩ
142.0kΩ
(178.0)kΩ
5.9
32.0kΩ
208.0kΩ
126.0kΩ
(185.0)kΩ
6.0
30.8kΩ
188.0kΩ
114.0kΩ
(192.0)kΩ
R1 = (Blue)
12.0
R2 = Black
For technical support and more information, see inside back cover or visit www.ti.com/powertrends
Application Notes
PT6100/6210/6300 Series
Using the Inhibit Function on Power Trends’
Wide Input Range Bus ISRs
For applications requiring output voltage On/Off control,
the 12pin ISR products incorporate an inhibit function.
The function has uses in areas such as battery conservation,
power-up sequencing, or any other application where the
regulated output from the module is required to be
switched off. The On/Off function is provided by the
Pin 1 (Inhibit) control.
Figure 1
The ISR functions normally with Pin 1 open-circuit,
providing a regulated output whenever a valid source
voltage is applied to Vin, (pins 2, 3, & 4). When a lowlevel2 ground signal is applied to Pin 1, the regulator
output will be disabled.
Inh
Figure 1 shows an application schematic, which details
the typical use of the Inhibit function. Note the discrete
transistor (Q1). The Inhibit control has its own internal
pull-up with a maximum open-circuit voltage of 8.3VDC.
Only devices with a true open-collector or open-drain
output can be used to control this pin. A discrete bipolar
transistor or MOSFET is recommended.
Equation 1 may be used to determine the approximate
current drawn by Q1 when the inhibit is active.
Equation 1
= Vin ÷ 155kΩ
PT6100/6210/6300
Vin
Vo
Inh*
1
C1, 1µF
(Optional)
GND
9,10,11
V out
Vo(adj)
5,6,7,8
12
C2
100µF
Q1
BSS138
+
COM
COM
Turn-On Time: The output of the ISR is enabled automatically
when external power is applied to the input. The Inhibit control
pin is pulled high by its internal pull-up resistor. The ISR
produces a fully regulated output voltage within 1-msec of
either the release of the Inhibit control pin, or the application
of power. The actual turn-on time will vary with the input
voltage, output load, and the total amount of capacitance connected to the output Using the circuit of Figure 1, Figure 2
shows the typical rise in output voltage for the PT6101
following the turn-off of Q1 at time t =0. The waveform was
measured with a 9Vdc input voltage, and 5-Ohm resistive load.
± 20%
Notes:
1. The Inhibit control logic is similar for all Power Trends’
modules, but the flexibility and threshold tolerances will be
different. For specific information on the inhibit function
of other ISR models, consult the applicable application
note.
2. Use only a true open-collector device (preferably a discrete
transistor) for the Inhibit input. Do Not use a pull-up
resistor, or drive the input directly from the output of a
TTL or other logic gate. To disable the output voltage,
the control pin should be pulled low to less than +1.5VDC.
3. When the Inhibit control pin is active, i.e. pulled low, the
maximum allowed input voltage is limited to +30Vdc.
Figure 2
6
5
4
Vo (Vdc)
Istby
2,3,4
V in
3
2
1
0
-0.2
4. Do not control the Inhibit input with an external DC
voltage. This will lead to erratic operation of the ISR and
may over-stress the regulator.
5. Avoid capacitance greater than 500pF at the Inhibit control
pin. Excessive capacitance at this pin will cause the ISR to
produce a pulse on the output voltage bus at turn-on.
6. Keep the On/Off transition to less than 10µs. This
prevents erratic operation of the ISR, which can cause a
momentary high output voltage.
For technical support and more information, see inside back cover or visit www.ti.com/powertrends
0
0.2
0.4
t (milli-secs)
0.6
0.8
1
PACKAGE OPTION ADDENDUM
www.ti.com
3-Jul-2009
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
PT6302A
NRND
SIP MOD
ULE
EBA
12
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
PT6302B
NRND
SIP MOD
ULE
EBK
12
12
Pb-Free
(RoHS)
Call TI
Level-1-215C-UNLIM
PT6302BT
NRND
SIP MOD
ULE
EBK
12
200
Pb-Free
(RoHS)
Call TI
Level-1-215C-UNLIM
PT6302C
NRND
SIP MOD
ULE
EBC
12
12
Pb-Free
(RoHS)
Call TI
Level-1-215C-UNLIM
PT6302CT
NRND
SIP MOD
ULE
EBC
12
200
Pb-Free
(RoHS)
Call TI
Level-1-215C-UNLIM
PT6302G
NRND
SIP MOD
ULE
EBG
12
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
PT6302H
OBSOLETE SIP MOD
ULE
EBH
12
TBD
Call TI
Call TI
PT6302J
OBSOLETE SIP MOD
ULE
EBJ
12
TBD
Call TI
Call TI
Lead/Ball Finish
MSL Peak Temp (3)
PT6302N
NRND
SIP MOD
ULE
EBD
12
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
PT6302R
NRND
SIP MOD
ULE
EBE
12
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
PT6302S
NRND
SIP MOD
ULE
EBF
12
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
PT6303A
NRND
SIP MOD
ULE
EBA
12
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
PT6303C
NRND
SIP MOD
ULE
EBC
12
12
Pb-Free
(RoHS)
Call TI
Level-1-215C-UNLIM
PT6303CT
NRND
SIP MOD
ULE
EBC
12
200
Pb-Free
(RoHS)
Call TI
Level-1-215C-UNLIM
PT6303G
NRND
SIP MOD
ULE
EBG
12
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
PT6303N
NRND
SIP MOD
ULE
EBD
12
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
PT6303R
NRND
SIP MOD
ULE
EBE
12
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
OBSOLETE SIP MOD
ULE
EBF
12
TBD
Call TI
Call TI
PT6303S
PT6304A
NRND
SIP MOD
ULE
EBA
12
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
PT6304B
NRND
SIP MOD
ULE
EBK
12
12
Pb-Free
(RoHS)
Call TI
Level-1-215C-UNLIM
PT6304C
NRND
SIP MOD
ULE
EBC
12
12
Pb-Free
(RoHS)
Call TI
Level-1-215C-UNLIM
PT6304G
NRND
SIP MOD
ULE
EBG
12
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
PT6304H
OBSOLETE SIP MOD
ULE
EBH
12
TBD
Call TI
Call TI
PT6304J
OBSOLETE SIP MOD
ULE
EBJ
12
TBD
Call TI
Call TI
EBD
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
PT6304N
NRND
SIP MOD
ULE
12
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
3-Jul-2009
Orderable Device
Status (1)
Package
Type
Package
Drawing
PT6304R
NRND
SIP MOD
ULE
EBE
12
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
PT6314A
NRND
SIP MOD
ULE
EBA
12
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
OBSOLETE SIP MOD
ULE
EBD
12
Pb-Free
(RoHS)
Call TI
N / A for Pkg Type
PT6314N
Pins Package Eco Plan (2)
Qty
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising