02_RSX_IntTrimKit

02_RSX_IntTrimKit
INSTALLATION
INSTRUCTIONS
Accessory
Application
INTERIOR TRIM KIT
P/N 08Z03-S6M-200
2002 RSX
Publications No.
BII 22651-23024
Issue Date
NOV 2001
Revised November 30, 2001
PARTS LIST
INSTALLATION
Left door handle trim
NOTE:
• Be careful not to damage the interior trim and the
body paint finish.
Right door handle trim
•
Right front console trim "A"
This interior trim kit should be installed only if the
ambient air temperature is 60°F (15°C) or above.
1.
Using isopropyl alcohol on a shop towel,
thoroughly clean the areas where the interior
trims will attach.
2.
Attach a piece of masking tape to the end of
each adhesive backing, and remove 5 to 6
inches of the adhesive backing from that end.
Fold the ends up, and attach them to the front
with masking tape. Remove the two small
adhesive backings from the front ends (the right
and left rear console trims only).
3.
Position the left door handle trim on the door
handle, and carefully remove the adhesive
backings from the trim while holding light
pressure on the trim. After installing, hold the
trim firmly against the door handle with the palm
of your hand, particularly at the edges.
Left front console trim "A"
Right front console trim "B"
Left front console trim "B"
Door Handle Trim:
Right rear console trim
Left rear console trim
DOOR HANDLE
ADHESIVE BACKINGS
(Attach a piece of masking tape to
the ends, and remove 5 to 6 inches
of adhesive backings. Fold the
ends up, and attach them to the
front with masking tape.)
Outlet trim "A"
(marked "C" on the back)
Outlet trim "B"
(marked "D" on the back)
SUPPLIES REQUIRED
Isopropyl alcohol
Shop towel
Masking tape
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
DOOR HANDLE
TRIM
4.
BII 22651-23024
E2334E2 (0111)
Install the right door handle trim using the same
method.
08Z03-S6M-2001-91
1 of 2
5.
Outlet Trim "A" and "B":
Remove the adhesive backings from the other trim
panels, and install them in order shown by using
the same method as for the door handle trims.
OUTLET TRIM A OUTLET
(Before attaching,
make sure that the
trim is marked "C"
on the back.)
Front Console Trims "A" and "B":
Align with
this line.
ADHESIVE BACKINGS
(Attach a piece of masking
tape to the ends, and remove
2 to 3 inches of adhesive
backings. Fold the ends up,
and attach them to the front
with masking tape.)
INSTALL LEFT
FRONT
CONSOLE TRIM
"A" FIRST
OUTLET
FRONT
CONSOLE
OUTLET TRIM B
(Before attaching, make
sure that the trim is
marked "D" on the back.)
ADHESIVE BACKINGS
(Attach a piece of masking
tape to the ends, and remove
5 to 6 inches of adhesive
backings. Fold the ends up,
and attach them to the front
with masking tape.)
OUTLET TRIM A/B
LEFT FRONT
CONSOLE TRIM "B"
MARKED "C" OR "D"
(Align with the bottom center.)
USE AND CARE
Rear Console Trim:
ADHESIVE BACKINGS
(Attach a piece of masking
tape to the ends, and
remove 5 to 6 inches of
adhesive backings. Fold the
ends up, and attach them to
the front with masking
tape.)
ADHESIVE BACKING
(Remove.)
Use a soft cloth or sponge dampened with a mild
detergent and water solution to clean the trim. Do not
use polishing waxes containing compounds or
degreasing agents to clean the trim.
Align with
this line.
PROJECTION
LEFT
REAR
CONSOLE
TRIM
REAR
CONSOLE
2 of 2
Align the ends of the
right and left rear
console trims with the
center of the projection
on the rear console.
RIGHT REAR
CONSOLE
TRIM
BII 22651-23024 (0111)
© 2001 American Honda Motor Co., Inc - All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising