115-1

115-1
ARMSTRONG PUMPS_______________________
ASTRO SERIES CIRCULATORS
The ASTRO line of circulators. Astros are available with self-lubricated bearing, vent plug for initial purging, and dynamically balanced stainless steel rotor assembly.
No need for mechanical seal; no coupler alignment failure. Pumps will accept flange sizes 3/4", 1", 1-1/4" & 1-1/2" (specify CI or BRZ). Same flange to flange
dimension as competitive small circulators. All Astros: 120 VOLT/60Htz
Order No.
Model No.
Description
CIRCULATORS
3-SPEED
110123307
ASTRO50CI
ASTRO 50 CI CIRC L/FLGS
110123308
ASTRO50BR
ASTRO 50 BRZ CIRC L/FLGS
ASTRO / "S" SERIES CIRC. PUMP ACCESSORIES
816013111
816013111
CI COMPANION FLANGE KIT, 3/4"
816012111
816012111
CI COMPANION FLANGE KIT, 1"
816011111
816011111
CI COMPANION FLANGE KIT, 1-1/4"
816009111
816009111
CI COMPANION FLANGE KIT, 1-1/2"
816013141
816013141
BRZ COMPANION FLANGE KIT, 3/4"
816012141
816012141
BRZ COMPANION FLANGE KIT, 1"
816011141
816011141
BRZ COMPANION FLANGE KIT, 1-1/4"
816009141
816009141
BRZ COMPANION FLANGE KIT, 1-1/2"
3
REPLACES
TACO 007F, 008F, 0010F
TACO 007BF, 008BF, 0010BF
Approx. GPM @ Listed Head (ft.)
2.5
5
10
15
18
18
17
17
13
13
7
7
CIRCULATOR SERIES "CIF" ISOLATION FLANGES
SPECIAL ORDER
SPECIAL ORDER
CI ISOLATION FLANGE, 1/2" NPT
CIF-075T
CIF-075T
CI ISOLATION FLANGE, 3/4" NPT
CIF-100T
CIF-100T
CI ISOLATION FLANGE, 1" NPT
CIF-125T
CIF-125T
CI ISOLATION FLANGE, 1 1/4" NPT
CIF-150T
CIF-150T
CI ISOLATION FLANGE, 1 1/2" NPT
SPECIAL ORDER
SPECIAL ORDER
SWT ISOLATION FLANGE, 1/2" SWEAT
SPECIAL ORDER
SPECIAL ORDER
SWT ISOLATION FLANGE, 3/4" SWEAT
SPECIAL ORDER
SPECIAL ORDER
SWT ISOLATION FLANGE, 1" SWEAT
SPECIAL ORDER
SPECIAL ORDER
SWT ISOLATION FLANGE, 1 1/4" SWEAT
SPECIAL ORDER
SPECIAL ORDER
SWT ISOLATION FLANGE, 1 1/2" SWEAT
NOTE: The "CIF" Series Flanges have slotted holes for universal Armstrong Pump applications.
Flanges will fit the "Astro", "E", "H" and "S" series pumps.
E SERIES CIRCULATORS
The ARMFlo line of circulators offers a competitive, compact, high efficiency, quiet, circulator with repairable
compontent design. The air cooled motor designed for this series is up to 74% more efficient than some wet
rotor pumps of similar power. Pumps will accept flange sizes 3/4", 1", 1-1/4" & 1-1/2" (specify CI or BRZ).
Same flange to flange dimension as competitive circulators.
Order No.
Model No.
CIRCULATORS
Special Order
ARMFLO E7
E9
ARMFLO E9
E9B
ARMFLO E9B
E11
ARMFLO E11
E11B
ARMFLO E11B
ARMFLO ACCESSORIES
810120204
810120204
Description
Voltage
ARMFLO CI CIRC 1/12 HP L/FLGS
ARMFLO CI CIRC 1/6 HP L/FLGS
ARMFLO BRZ CIRC 1/6 HP L/FLGS
ARMFLO CI CIRC 1/6 HP L/FLGS
ARMFLO BRZ CIRC 1/6 HP L/FLANGS
120/60
120/60
120/60
120/60
120/60
HARDWARE KIT FOR E11/E11B
E SERIES CIRCULATORS
The ARMFlo line of circulators offers a competitive, compact, high efficiency, quiet, circulator with repairable
compontent design. The air cooled motor designed for this series is up to 74% more efficient than some wet
rotor pumps of similar power. Pumps will accept flange sizes 3/4", 1", 1-1/4" & 1-1/2" (specify CI or BRZ).
Same flange to flange dimension as competitive circulators.
Order No.
Model No.
CIRCULATORS
Special Order
ARMFLO E7
E9
ARMFLO E9
E9B
ARMFLO E9B
E11
ARMFLO E11
E11B
ARMFLO E11B
ARMFLO ACCESSORIES
810120204
810120204
62
Description
ARMFLO CI CIRC 1/12 HP L/FLGS
ARMFLO CI CIRC 1/6 HP L/FLGS
ARMFLO BRZ CIRC 1/6 HP L/FLGS
ARMFLO CI CIRC 1/6 HP L/FLGS
ARMFLO BRZ CIRC 1/6 HP L/FLANGS
ARMSTRONG ASTRO SERIES
Voltage
120/60
120/60
120/60
120/60
120/60
HARDWARE KIT FOR E11/E11B
www.federalcorp.com
7/30/2008
_______________________ ARMSTRONG PUMPS
S & H SERIES CIRCULATORS
Both S and H Series circulators feature unique Armstrong shaft and bearing module for ease of serviceability and maximum
interchangeability. Features include oversized shafts of alloy steel and impellers constructed from non-ferrous material designed for
optimal water delivery. Every circulator operated before shipment. Available in bronze fitted or all bronze. 1750 RPM motors.
Order No.
CI BODY, BF
S25BF
S35BF
H32BF
H51BF1PH
ALL BRONZE
S25AB
H32AB
H41AB
Model No.
Flange Sizes (NPT)
S-25 BF
S-35 BF
H-32 BF
H-51 BF
CI
CI
CI
CI
3/4", 1", 1-1/4", 1-1/2"
2"
1", 1-1/4", 1-1/2"
1"
S-25 AB
H-32 AB
H-41 AB
BRZ 3/4", 1", 1-1/4", 1-1/2"
BRZ 1", 1-1/4", 1-1/2"
BRZ 1"
HP
V/Ph.
Flg-Flg Dimension
1/12
1/6
1/6
1/4
115/1
115/1
115/1
115/1
6-1/2"
8-1/2"
8-1/2"
11-1/2"
1/12
1/6
1/6
115/1
115/1
115/1
6-1/2"
8-1/2"
8-1/2"
Replacement for:
B&G
Taco
Ser. 100
110
2"
120
HV
111
60-11
1600
Ser.100AB
HV-AB
1" PR
110B
111B
113B
3
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
• (918) 249-1918
(800) ARMSTRONG
955-1918S & H•SERIESFAX: (918) 249-9014
63
6/17/2008
ARMSTRONG PUMPS_______________________
1050/1060 SERIES CIRCULATORS
These custom circulators feature the classic horizontal in-line design, engineered for durability and smooth operation.
Designed for large flow applications. Custom sized impellers and motors are fine-tuned to meet the exact system
requirements. 1050 Series has unique Armstrong shaft and bearing module for ease of serviceability. 1060 Series has extra
long brz sleeve bearings to keep shaft in perfect alignment and quiet operation. Available in all-bronze and bronze-fitted
construction.
Max. Op. Temp. 225oF; Max. Working Pres. 175 psi
3
Order No.
Model No.
1050 SERIES CI BODY, BRZ FITTED
1050BF1PH.3B1.5
1050-1.5B
1050BF1PH.5B1.5
1050-1.5B
1050BF3PH.5B1.5
1050-1.5B
1050BF1PH.5B2
1050-2B
1050BF1PH.75B2
1050-2B
1050BF1PH1B2
1050-2B
1050 SERIES ALL BRONZE
1050AB1PH.5B1.5
1050-1.5B
1050AB1PH.5B2
1050-2B
1050AB1PH.75B2
1050-2B
1060 SERIES CI BODY, BRZ FITTED
1060BF1PH1D1.5
1060-1.5D
1060BF3PH1D1.5
1060-1.5D
1060BF1PH1D2
1060-2D
1060BF3PH1D2
1060-2D
1060BF3PH1.5D2
1060-2D
1060BF3PH2D2
1060-2D
Flg Size
(NPT)
HP
V/Ph.
Flg-Flg Dimension
Imp. Trim
(in.D)
1/3
1/2
1/2
1/2
3/4
115/230/1
115/230/1
230/460/3
115/230/1
115/230/1
115/230/1
11-1/2"
11-1/2"
11-1/2"
11-1/2"
11-1/2"
11-1/2"
4.75"
5.15"
5.15"
4.5"
5.O"
5.25"
1-1/2"
2"
2"
1/2
1/2
3/4
115/230/1
115/230/1
115/230/1
11-1/2"
11-1/2"
11-1/2"
5.15"
4.5"
5.O"
1-1/2"
1-1/2"
2"
2"
2"
2"
1
1
1
1
1-1/2
2
115/230/1
230/460/3
115/230/1
208-230/460/3
208-230/460/3
208-230/460/3
13-1/2"
13-1/2"
14"
14"
14"
14"
6.5"
6.5"
5.85"
5.85"
6.55"
7.0"
1-1/2"
1-1/2"
1-1/2"
2"
2"
2"
1
Please see pages 330 through 337 for useful information on
pumps, including sizing and selecton tips.
64
www.federalcorp.com
ARMSTRONG 1050-1060 SERIES
_______________________ARMSTRONG PUMPS
UNIVERSAL SEAL/BEARING ASSEMBLY
FOR MOST STANDARD ARMSTRONG AND BELL & GOSSETT IN-LINE CIRCULATING PUMPS
Here is a new concept in replacement parts standardization with significant advantages for stocking wholesalers, pump
maintenance firms, institutions and large commercial and industrial users of circulating pumps.
It is based on a new Universal seal bearing assembly design which incorporates an interchangeable pump shaft bearing module.
With as few as five types of seal bearing assemblies on hand, more than 100 different Armstrong and B&G pump models can be
converted to this new module program during routine maintenance. Once the conversion is made, future maintenance will normally
require replacement of the pump shaft bearing module only. Since all seal bearing assemblies accept the same module, and
elaborate and costly parts inventories are not required.
3
The Armstrong Universal Seal/Bearing Conversion Assembly is available in one construction replacing standard, bronze-fitted or all
bronze construction. It features a positive mechanical seal in the well-known "ARMSEAIN' construction... a tried and proven method
of preventing water leakage. Made of long-lasting, hard-wearing materials, it ensures many years of noise-free, trouble-free, service.
A dependable, quiet-operating, oil-lubricated sleeve bearing with a new superior oiling design offers long-life operation.
The shaft module has an alloy steel shaft with copper sleeve and positive oil O-ring seals.
Materials: Pump shaft bearing module
Shaft: Alloy Steel
Seal: "ARMSEAL" positive mechanical
Bearing: copper sleeve oil lubricated
**
**
**
**
**
**
** Can also be used on 1050 Series circulators
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
65
ARMSTRONG PUMPS_______________________
CIRCULATOR AND STOCK PUMP PARTS AND ACCESSORIES
3
Order No.
IMPELLERS
812961111
816322111
816305328
816301325
816302319
816302047
816304047
116304317-4.5
116302317-4.5
116303317-5.15
11604047-5.0
116304317-5.0
MOTORS
410191062
805316010
817025001
817025007
816141001
831009062
831011083
Model No.
Description
For Use With Model(s)
812961-111
816322111
816305-328
816301-325
816302-319
816302-047
816304-047
116304317
116302317
116303317
11604047
116304317
IMPELLER NFI (2.75")
IMPELLER NFI (3.375")
IMPELLER 3.875"
IMPELLER PLASTIC (4.25")
IMPELLER NFI (5.0")
IMPELLER BRZ FULL TRIM (5.25")
IMPELLER BRZ FULL TRIM (5.25")
IMPELLER PLASTIC 4.50" TRIM
IMPELLER PLASTIC 4.50" TRIM
IMPELLER PLASTIC 5.15" TRIM
IMPELLER BRZ 5.0" TRIM
IMPELLER PLASTIC 5.00" TRIM
S-25
S-35, H-32
S-45
H-41
H51/1050-1B
H-52
H-54
H-54/1050-2B
1050-1.25B
1050-1.5B
1050-2-B
1050-2B, 1060-2D
410191-062
805316-010
817025-001
817025-007
816141-001
831009-062
831011-083
1/2 HP 115/230/1 MOTOR 3450 RPM
1/12 HP 115/1 1800 RPM
1/6 HP 115/1 1725 RPM
1/4 HP 115/60/1 1800 RPM
1/4 HP 115/1 1800 RPM
1/2 HP 115/230/1 1800 RPM
1/2 HP 208-230/460/3 1800 RPM
702S PUMP
S-25
S-35, H-32
S-45
H-51
H-53, 1050, 1060
H-53, 1050, 1060
831010062
831012083
831010-062
831012-083
3/4 HP 115/230/1 1800 RPM
3/4 HP 208-230/460/3 1800 RPM
1050, 1060
H-54, 1050, 1060
816676069
816676-069
1 HP 208-230/460/3 1800 RPM
S-69, 1050, 1060
FLANGES 1
106074011
804301111
804300111
804300141
804301141
806073111
806073141
816009211
816009241
816011211
816011241
816012211
816013211
816013241
816009111
816009141
816011111
816011141
816012111
816012141
816013111
816013141
GASKETS
104442000
106049000
106050000
106158000
106074-011
804301-111
804300-111
804300-141
804301-141
806073-111
806073-141
816009-211
816009-241
816011-211
816011-241
816012-211
816013-211
816013-241
816009-111
816009-141
816011-111
816011-141
816012-111
816012-141
816013-111
816013-141
2 BRZ FLG (PER EA)
1-1/2 FLG KIT CI (2 FLGS)
1-1/4 FLG KIT CI (2 FLGS)
1-1/4 FLG KIT BRZ (2 FLGS)
1-1/2 FLG KIT BRZ (2 FLGS)
1 FLG KIT CI (2 FLGS)
1 FLG KIT BRZ (2 FLGS)
1-1/2 FLG KIT CI (2 FLGS)
1-1/2 FLG KIT BRZ (2 FLGS)
1-1/4 FLG KIT CI (2 FLGS)
1-1/4 FLG KIT BRZ (2 FLGS)
1 FLG KIT CI (2 FLGS)
3/4 FLG KIT CI (2 FLGS)
3/4 FLG KIT BRZ (2 FLG)
1-1/2 FLG KIT CI (2 FLGS)
1-1/2 FLG KIT BRZ 2 FLGS)
1-1/4 FLG KIT CI (2 FLGS)
1-1/4 FLG KIT BRZ (2 FLGS)
1 FLG KIT CI (2 FLGS)
1 FLG KIT BRZ (2 FLGS)
3/4 FLG KIT CI (2 FLGS)
3/4 FLG KIT BR (2 FLGS)
4360, H54
E10/E11/E13
E10/E11/E13
E10/E11/E13B
E10/E11/E13B
E10/E11/E13
E10/E11/E13B
E8/E9
E8B/E9B
E8/E9
E8B/E9B
E8/E9
E8/E9
E8B/E9B
ASTRO, S25
ASTRO, S25
ASTRO, S25
ASTRO, S25
ASTRO, S25
ASTRO, S25
ASTRO, S25
ASTRO, S25
104442-000
106049-000
106050-000
106158-000
BODY GASKET
BODY GASKET
BODY GASKET
BODY GASKET
106592000
106592-000
BODY GASKET
804034000
804034-000
FLANGE GASKET (PER SET)
S-25
S-35, H-32
S-45, S-46, H-41
1050 SERIES, S-55,
S57,H51, to H-54
1060 Series, S-69,
H-63 to H-68
H-32, 1-1/2D
Replaces B&G #
118840, 189132,
118666, 118435
186360
186359
118626
111034
111036, 111031
111040
169035
111046 2
3
111049 2 3
169089, 169090,
111051 3
P04080
P04890
P05800
P57410
P57700
118373
ARMSTRONG CIRC PARTS & ACCESSORIES
66
www.federalcorp.com
7/28/2008
_______________________ARMSTRONG PUMPS
CIRCULATOR AND STOCK PUMP PARTS AND ACCESSORIES
Order No.
Model No.
IMPELLERS
GASKETS con't
812961111
812961-111
805176000
805176-000
816322111
816322111
816305328
816305-328
105176001
105176-001
816301325
816301-325
816302319
816302-319
816302047
816302-047
805209000
805209-000
816304047
816304-047
810120202
810120-202
116304317-4.5
116304317
810120204
810120-204
116302317-4.5
116302317
810120212
810120-212
116303317-5.15 116303317
810120218
810120-218
11604047-5.0
11604047
116304317-5.0
116304317
816117000
816117-000
MOTORS
410191062
410191-062
816653000
816653-000
805316010
805316-010
880200071
880200-071
817025001
817025-001
AS1170-363
AS1170-363
817025007
817025-007
MECHANICAL SEALS
816141001
816141-001
816706021
816706-021
831009062
831009-062
831011083
831011-083
816706023
816706-023
831010062
831010-062
816707001
816707-001
831012083
831012-083
825458001
825458-001
816676069
816676-069
975000991
975000-991
975000993
975000-993
1
FLANGES
633
633
106074011
106074-011
804301111
804301-111
BEARING ASSEMBLIES
804300111
804300-111
810119001
810119001
804300141
804300-141
816549091
816549-091
804301141
804301-141
806073111
806073-111
816027002
816027-002
806073141
806073-141
816032000
816032-000
816009211
816009-211
816009241
816009-241
816366041
816366-041
816011211
816011-211
816999041
816999-041
816011241
816011-241
COUPLER ASSEMBLIES
816012211
816012-211
806026001
806026-001
816013211
816013-211
816013241
816013-241
806137000
806137-000
816009111
816009-111
816009141
816009-141
816011111
816011-111
806168001
806168-001
816011141
816011-141
807436000
807436-000
816012111
816012-111
816012141
816012-141
810120003
810120-003
816013111
816013-111
810120006
810120-006
816013141
816013-141
816665000
816665-000
GASKETS
MISCELLANEOUS
104442000
104442-000
410133181
410133-181
106049000
106049-000
810120050
810120-050
106050000
106050-000
106158000
106158-000
874055000
874055-000
Description
For Use With Model(s)
IMPELLER
NFI (2.75")
FLANGE GASKET
(PER SET)
IMPELLER NFI (3.375")
IMPELLER
3.875"
FLANGE GASKET
IMPELLER PLASTIC (4.25")
IMPELLER NFI (5.0")
IMPELLER BRZ FULL TRIM (5.25")
FLANGE GASKET (PER SET)
IMPELLER BRZ FULL TRIM (5.25")
FLG GSKT, BOLT & NUT KIT
IMPELLER PLASTIC 4.50" TRIM
FLG GSK, BOLT & NUT KIT
IMPELLER PLASTIC 4.50" TRIM
FLG GSKT, BOLT & NUT KIT
IMPELLER PLASTIC 5.15" TRIM
FLG GSKT, BOLT & NUT KIT
IMPELLER BRZ 5.0" TRIM
IMPELLER PLASTIC 5.00" TRIM
FLANGE GASKET KIT
1/2 HP 115/230/1 MOTOR 3450 RPM
FLG GASKET
SET1800
(2) RPM
1/12
HP 115/1
BODY
E10/E10B/E11/ELLB
1/6
HPGSKT
115/1
1725 RPM
GASKET
CASING O'RING
1/4
HP 115/60/1
1800 RPM
1/4 HP 115/1 1800 RPM
SEALHP
KIT115/230/1
SMALL CIRCS
1/2
1800 RPM
1/2 HP 208-230/460/3 1800 RPM
SEAL KIT VITON HI-TEMP SEAL
3/4 HP 115/230/1 1800 RPM
SEAL KIT 3/4"D LARGE CIRCS
3/4 HP 208-230/460/3 1800 RPM
SEAL KIT 1.25" TYPE 21 BP-1C1
1 HP 208-230/460/3 1800 RPM
SEAL KIT 1.25" EDPM TYPE 21
SEAL KIT 1.625" EDPM TYPE 21
SEAL 5/8" TYPE 21
2 BRZ FLG (PER EA)
1-1/2 FLG KIT CI (2 FLGS)
1-1/4
FLG KIT
(2 FLGS)
UNIV SEAL
BRGCIASSY
#2
1-1/4
FLG KIT
(2 #3
FLGS)
UNIV SEAL
BRGBRZ
ASSY
1-1/2 FLG KIT BRZ (2 FLGS)
1
FLGSEAL
KIT CIBRG
(2 FLGS)
UNIV
ASSY #4
1
FLGSEAL
KIT BRZ
FLGS)
UNIV
BRG(2ASSY
#5
1-1/2 FLG KIT CI (2 FLGS)
1-1/2
FLG
KIT
BRZ
(2
FLGS)
UNIV SEAL BRG ASSY #6
1-1/4
KIT CI (2MODULE
FLGS)
SHAFTFLG
& BEARING
1-1/4 FLG KIT BRZ (2 FLGS)
1
FLG KIT 1/2
CI (2XFLGS)
COUPLER
1/2 CCWR
3/4 FLG KIT CI (2 FLGS)
3/4
FLG KIT BRZ
(25/8
FLG)(flex spacer style)
3J COUPLER
1/2 X
1-1/2 FLG KIT CI (2 FLGS)
1-1/2 FLG KIT BRZ 2 FLGS)
1-1/4
FLG1/2
KIT XCI1/2
(2 FLGS)
COUPLER
CCWR
1-1/4
FLG KIT1/2
BRZ
(2 FLGS)
3J COUPLER
X 1/2
CWR (flex spacer style)
1 FLG KIT CI (2 FLGS)
1
FLG
KIT
BRZ
(2
FLGS)
COUPLER 1/2 X 1/2 CWR
3/4
FLG KIT
CIX(25/8
FLGS)
COUPLER
1/2
CWR
3/4
FLG KIT BR
4J COUPLER
5/8(2X FLGS)
5/8 CWR
H-51
S-25 to
57,H-32
to 54,
H-53,
1050,
1060
1050 1050,
SERIES1060
H-53,
LAARS BOILERS
1050, 1060
1060 SERIES
H-54, 1050, 1060
BODY
WATERGASKET
SLINGER 410133-181
BODY
GASKET
MOTOR
MOUNT KIT FOR 48 FRAME MARATHON
BODY GASKET
BODY
GASKET
MOTOR
MOUNT KIT FOR 56 FRAME MARATHON
S-25
S-35, H-32
S-45, S-46, H-41
1050 SERIES, S-55,
S57,H51, to H-54
1060 Series, S-69,
H-63 to H-68
H-32, 1-1/2D
106592000
106592-000
BODY
GASKET BODY 3D 4360/1060
816646011
816646-011
CASING/PUMP
974507100
974507-100
IMPELLER KEY (WOODRUFF #2)
804034-000
FLANGE GASKET (PER SET)
1804034000
"Kit" consists of flanges, gasket & hardware.
2
3
OKLAHOMA CITY
(800) 289-3331
•
•
S-25
H-41,51,52,53,
S-35,
H-32
1050-1,
1-1/4, 1-1/2
S-45
H32, H51, 1050-1B,
H-41
H52, 1050-1-1/4B, H53,
H51/1050-1B
1050-1-1/2B
H-52
S-35
H-54
S-25, ASTRO
H-54/1050-2B
E11
1050-1.25B
1050-2B, 1060-2D
1050-1.5B
H-41,51,52,53,
1050-2-B
1050-1, 1-1/4, 1-1/2
1050-2B, 1060-2D
H-54,66,67,68,
1050-2B, 1060-2D
702S PUMP
S-25
S-25
E10/E10B/E11/E11B
S-35,
H-32
4270 SERIES
S-45
S-69, 1050, 1060
4270 SERIES (SAME AS
4360,
H54
810134-000)
E10/E11/E13
E10/E11/E13
S-25
E10/E11/E13B
S-34, S-35, H-32
E10/E11/E13B
E10/E11/E13
S-45, S-46, H-41
E10/E11/E13B
H-51 to 54, 1050
E8/E9
E8B/E9B
1-1/2D & 2D 1060
E8/E9
FITS BRG ASSY #2-5
E8B/E9B
E8/E9
S-25, S-35, H-32, H-41
E8/E9
E8B/E9B
H-51&H-52 (3PH), 1050
ASTRO,
S25HP 3PH, 1/2
1/4 & 1/3
ASTRO,
S25
& 3/4 HP
1 & 3 PH
ASTRO,
S25
S45, S46
ASTRO,
S25 (1PH), 1050
H-51 & H-52
ASTRO,
S25HP
1/4 & 1/3
ASTRO,
S25
H-51, H-52
ASTRO,
S25
H-53, H-54
ASTRO,
S25 2D
1060 1-1/2D,
Replaces B&G #
118840,
118368 189132,
118666, 118435
186360
186359
118065
118626
118378
118368
111034
111036, 111031
111040
169035
118681
111046 2
3
111049 2 3
186860
169089, 169090,
111051 3
3
118844, 189034
189100, 189101,
189102, 189103
189105, 189106,
186863, 186864,
186865
118705, 189110,
118712, 118709,
118709
118723
118473
118709
118476, P77265
P04080
P04890
P05800
P57410
P57700
118373
When replacing B & G motor, also replace coupler with 806137-000.
Rigid mount ball bearing motor can replace resilient mount motor.
(405) 239-7301
FAX: (405) 232-5438
ARMSTRONG CIRC PARTS & ACCESSORIES
7/28/2008
ARMSTRONG CIRC PARTS & ACCESSORIES
7/28/2008
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
67
ARMSTRONG PUMPS_______________________
HYDRONIC SPECIALTIES
Armstrong's quality specialty items are ideal for commercial hydronic systems to control air, water pressure, and to
attach the system to a conventional expansion tank.
Order No.
RD11U
RD40-SPECIAL ORDER
Model No.
216944-300
207937-343
C11U
TMA24
216945-300
213991-307
Description
PRES REDUCING VALVE, BRZ BODY, 12 PSI
PRES REDUCING VALVE, BRZ BODY, 12 PSI
(REPLACED BY #A41-12 CASH ACME)
DUAL CONTROL, PRES RED 12# & RELIEF 30#
EXPANSION TANK FITTING
ART446
572017-004
AIR REMOVAL TRAP (AIR SCOOP)
Size
1/2"
3/4"
1/2"
1/2" TANK 3/4"
SYSTEM
2"
3
4270 SERIES CENTRIFUGAL STOCK
PUMPS
Series 4270 end-suction motor mounted pumps are your
competitive choice for cooling towers, HVAC and general purpose
pumping applications. Construction from iron body, high strength
engineered resin (ULTEM) impellers, SS shaft, SS faceplate, with
3600 RPM ODP motors make this a quality multi-use pump.
Popular sizes are stocked in both single and three phase motors.
Order
No.
702S
703S
703T
704S
704T
708S
708T
709T
68
Replacing STA-RITE
Model
JBMC
JBMD
JBMD3
JBME
JBME
JBMF
JBMF3
JBMG
HP
1/2
3/4
3/4
1
1
1-1/2
1-1/2
2
Ph./V
1/115/230
1/115/230
3/230/460
1/115/230
3/230/460
1/115/230
3/230/460
3/230/460
Size
1 x 1.25
1 x 1.25
1 x 1.25
1 x 1.25
1 x 1.25
1.5 x 2
1.5 x 2
1.5 x 2
www.federalcorp.com
ARMSTRONG HYDRONIC SPEC
7
_______________________ARMSTRONG PUMPS
-
4360 & 4380 VERTICAL IN-LINE MOTOR MOUNTED PUMPS
Armstrong's line of quality vertical inline pumps is the broadest in the industry. The advantages of space saving, ease of installation, and
maintenance superiority make this the pump of choice. All sizes are listed below in composite curves. Federal has the ability to assemble
from a kit, 11 of the most popular sizes. Using factory computer software, a pump size, motor and exact impeller trim can be selected.
The components can quickly be assembled into a complete pump to meet your exact requirements. Contact a salesperson to help you
with your custom pump needs.
4360 Series
Order No.
MODEL 4360
PK4360-2D
MODEL 4380
PK4380-1.5X8-14
PK4380-1.5X8-21
PK4380-2X6-143
PK4380-2X6-213
PK4380-3X6-143
PK4380-3X6-213
PK4380-4X6-143
PK4380-2X8-143
Model Size
Motor Fr. Size
2" ,MODEL 2D
143-184JM
1.5 X 1.5 X 8
1.5 X 1.5 X 8
2X2X6
2X2X6
3X3X6
3X3X6
4X4X6
2X2X8
143-184 JM
213-215 JP
143-184 JM
213-215 JM
143-184 JM
213-215 JM
143-184 JM
143-184 JM
Order No.
MODEL 4380 con't
PK4380-3X8-143
PK4380-3X8-213
PK4380-4X8-143
PK4380-4X8-213
PK4380-2X10-143
PK4380-2X10-213
PK4380-3X10-143
PK4380-3X10-213
PK4380-4X10-213
PK4380-4X10-254
Model Size
Motor Fr. Size
3X3X8
3X3X8
4X4X8
4X4X8
2 X 2 X 10
2 X 2 X 10
3 X 3 X 10
3 X 3 X 10
4 X 4 X 10
4 X 4 X 10
143-184 JM
213-215JP
143-184 JM
213-215 JP
143-184 JM
213-215 JP
143-184 JM
213-215 JP
213-215 JP
254-256 JM
3
4360 Series
4360 & 4380 VERTICAL IN-LINE MOTOR MOUNTED PUMPS (cont.)
4360 Series
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
69
ARMSTRONG PUMPS_______________________
4360 & 4380 VERTICAL IN-LINE MOTOR MOUNTED PUMPS (cont.)
4380 Series ( and 4300 Series)
3
ARMSTRONG 4360 4380 PUMP KITS
70
www.federalcorp.com
_______________________ARMSTRONG PUMPS
Federal assembles pumps!
Good news! Federal
has been authorized
by Armstrong to assemble pumps. Over
20 different sizes
and styles of pumps
are on the shelf
ready to be assembled to either 1750
or 3500 RPM motors. 2 to 20 HP pumps
can be assembled in one hour to two days,
depending on availability of motor and impeller. Software makes selection a breeze.
3
Your pump headaches are a thing of the past. Ask us for cross-references, literature and
a CD containing Armstrong’s powerful software.
Let us help you with all of your pump, hydronic
specialty, heat exchanger and engineered products
requirements.
Please read Tech Tip #26 on page 331 for proper
pump sizing and selection tips.
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
71
ARMSTRONG PUMPS_______________________
3
Armstrong is known for pioneering the vertical in-line pumps in
HVAC applications. The 4300
Series is the ultimate industry for
both features and sizes available.
See the 4380 Composite
Curves to view most of the
similar 4300 sizes.
72
www.federalcorp.com
_______________________ARMSTRONG PUMPS
3
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
73
ARMSTRONG PUMPS_______________________
3
74
www.federalcorp.com
_______________________ARMSTRONG PUMPS
4280 END SUCTION MOTOR MOUNTED PUMPS
Armstrong's broad line of quality end suction pumps can be ordered from the factory, or Federal has the ability to assemble from a kit,
11 of the most popular sizes highlighted on the composite list below. Using factory computer software, a pump size, motor and exact
impeller trim can be selected to meet your exact conditions. The components can quickly be assembled into a complete pump. Contact
a salesperson to help you with your custom pump needs.
Order No.
PK4280-2X6-143
PK4280-2X6-213
PK4280-2.5X6-14
PK4280-2.5X6-21
PK4280-1X8-143
PK4280-1.5X8-14
PK4280-2X8-143
PK4280-2.5X8-14
PK4280-3X8-143
PK4280-3X8-213
Pump Size
3X2X6
3X2X6
3 X 2.5 X 6
3 X 2.5 X 6
1.5 X 1 X 8
3 X 1.5 X 8
3X2X8
3 X 2.5 X 8
4X3X8
4X3X8
Motor Fr. Size
143-184 JM
213-215 JM
143-184 JM
213-215 JM
143-184 JM
143-184JM
143-184 JM
143-184 JM
143-184 JM
213-215 JP
Order No.
PK4280-4X8-213
PK4280-2X10-143
PK4280-2X10-213
PK4280-2.5X10-1
PK4280-2.5X10-2
PK4280-3X10-213
PK4280-3X10-254
PK4280-4X10-254
Pump Size
5 X 4 X 8W
3 X 2 X 10
3 X 2 X 10
3 X 2.5 X 10
3 X 2.5 X 10
4 X 3 X 10
4 X 3 X 10
5 X 4 X 10
3
ps!
Pum re
t
n
a
Inst arked a it
m
in k
ps
Pum d in OKC e aske
nb
stoc and ca iately!
d
form imme
d
e
bl
sem
OKLAHOMA CITY
(800) 289-3331
Motor Fr. Size
213-215 JP
143-184JM
213-215 JP
143-184 JM
213-215 JP
213-215 JP
254-256 JM
254-256 JM
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
ARMSTRONG 4280 PUMP KITS
75
ARMSTRONG PUMPS_______________________
4030 SERIES HORIZONTAL PUMPS
A comprehensive range of single stage, end suction, radially-split centrifugal pumps designed for a wide variety of
applications. Features self-venting casing to prevent air binding, heavy duty bearings that are sealed and lubricated
for life, back pull-out bearing frame for easy removal, and self-lubricating mechanical seal to prevent liquid
seepage. Available in bronze-fitted, all bronze and all iron construction. Sizes up to 8 X 6 X 13 with heads to 600
feet and flows to 2000 GPM. See the 4280 Curves to view most of the similar 4030 Sizes.
4600 SERIES HORIZONTAL SPLIT CASE PUMPS
The 4600 Series of pumps capitalize on the "Tilted Parting" concept to minimize turbulence at the eye of the impeller by its
straight laminar approach, thus maximazing efficiency. This also results in the lowest profile and minimum floor space of any
HSC pump on the market today. They are designed with commonality of parts, low installation cost, and ease of maintenance
objectives. Twelve sizes up to 12 X 10 X 15 provide a range of flows to 5000 GPM and heads of up to 600 feet.
NOTE: THESE ARE SPECIAL ORDER ONLY.
3
76
www.federalcorp.com
ARMSTRONG 4030 SERIES
_______________________ARMSTRONG PUMPS
FLO-TREX VALVES
Flo-Trex combination valves combine the features of a check valve, throttling valve, and a shut-off valve, and are designed for
installation on the discharge side of centrifugal pumps. Multi-turn valve allows precise adjustment instead of more crude
quarter turn adjustment. The convertible body design permits the valve to be changed on site from the straight to the angle
configuration. Available in 2 1/2" to 12" sizes. Standard construction: CI valve body, SS and bronze trim, with class 125
flanges. Also available with ductile iron body for higher pressures, and grooved end connections.
FSA
Order No.
FSA015
FSA2
FSA2.5
FSA3
FTV2.5FS
FTV3FS
FTV4FS
Special Order
FTV6FS
Special Order
Special Order
Special Order
Straight Model No.
FSA-1-1/2
FSA-2
FSA-2-1/2
FSA-3
FTV-2.5FS
FTV-3FS
FTV-4FS
FTV-5FS
FTV-6FS
FTV-8SFS
FTV-10FS
FTV-12FS
Angle Model No.
FSA-1-1/2
FSA-2
FSA-2-1/2
FSA-3
FTV-2.5FA
FTV-3FA
FTV-4FA
FTV-5FA
FTV-6FA
FTV-8FA
FTV-10FA
FTV-12FA
Flg Size
1-1/2
2
2-1/2
3
2-1/2"
3"
4"
5"
6"
8"
10"
12"
3
SUCTION GUIDES
Armstrong's Model SG suction guides are designed for direct mounting to the suction side of horizontal or vertical
pumps. Guide vanes provide proper flow conditions by reducing water turbulence to minimize stress on pump
parts. Space savings are achieved through elimination of long radius elbow, suction entrance pipe, and
conventional 'Y' strainer. Available in sizes 2" to 14" Flg. connections and supplied with fine mesh brass start up
strainer and permanent strainer. Body and cover made from cast iron; strainer is SS. Max. working
pressure/temperature, 175 psi/300oF.
Order No.
Special Order
Special Order
Special Order
SG32
Special Order
SG33
SG43
SG44
Special Order
SG64
Special Order
SG65
SG86
Special Order
Special Order
Special Order
Special Order
Special Order
Special Order
Special Order
Special Order
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
SG-215
Model No.
Size
2 X 2-1/2
SG-2515
SG-252
SG-32
SG-2525
SG-33
SG-43
SG-44
SG-54
SG-64
SG-55
SG-65
SG-86
SG-88
SG-108
SG-1010
SG-1210
SG-1212
SG-1412
SG-1414
SG-1614
2.5 x 1.5
2.5 x 2
3x2
2.5 x 2.5
3x3
4x3
4x4
5x4
6x4
5x5
6x5
8x6
8x8
10 x 8
10 x 10
12 x 10
12 x 12
14 x 12
14 x 14
16 x 14
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
ARMSTRONG FLO-TREX
77
ARMSTRONG PUMPS_______________________
CIRCUIT BALANCING VALVES
CBV's feature multi-turn adjustment for detailed control, hidden memory stop to set balance point, and soft seats for positive
shutoff. CBV's offer much greater accuracy in adjustment compared to quarter turn valves. All Armstrong CBV models
feature precision flow measurement, pump throttling, and temperature measurement capabilities. Models from 2-1/2" to
12" feature flange or groove connections which can either be set in straight or 90 degree elbow configurations.
3
Order No.
THREADED ENDS
CBV-8T
CBV-12T
CBV010T
CBV012T
CBV015T
CBV020T
SOLDER ENDS
CBV-8S
CBV-8S-LF (LOW FLOW)
CBV-12S
CBV-12S-LF (LOW FLOW)
CBV010S
CBV012S
CBV015S
CBV020S
FLANGED ENDS
CBV025F
CBV030F
CBV040F
CBV060F
Model No.
Model No.
Size
CBV-1/2T
CBV-3/4T
CBV-1T
CBV-1-1/4T
CBV-1-1/2T
CBV-2T
1/2"
3/4"
1"
1-1/4"
1-1/2"
2"
CBV-1/2S
CBV-1/2S-LF
CBV-3/4S
CBV-3/4S-LF
CBV-1S
CBV-1-1/4S
CBV-1-1/2S
CBV-2S
1/2"
1/2"
3/4"
3/4"
1"
1-1/4"
1-1/2"
2"
CBV-2-1/2FS
CBV-3FS
CBV-4FS
CBV-6FS
2-1/2"
3"
4"
6"
Order No.
CBV ACCESSORIES
SPECIAL ORDER
CBVRULE
Description
CBDM-200
570109-203
CBV METER, 0-200", WITH HOSES AND CARRYING CASE
CBV CIRCULAR SLIDE RULE
CBVRULEV
570109-204
CBV CIRCULAR SLIDE RULE FOR USE WITH V
www.federalcorp.com
78
cbv's
ARMSTRONG CBV SERIES
9
_______________________ARMSTRONG PUMPS
VA/VAS VORTEX AIR SEPARATORS
Air in hydronic systems can hinder flow, inhibit heat transfer, and cause corrosion in piping systems. The circulation of
water into the VA seperator causes a vortex, or whirlpool action forcing the air to the center of the tank where it is
returned to the expansion tank or vented to atmosphere. Tanks are constructed to ASME standards. Sizes 2"-3" CI
body, thrd conn. Sizes 4"-24" fab steel body, flg conn.
Max pres/temp
Suggested Flow (GPM)
Order No. (less
strainer)
Special Order
Special Order
VA030T
VA040F
Special Order
VA060F
Special Order
Special Order
Special Order
Special Order
Special Order
Special Order
Special Order
Special Order
Special Order
Model (less
strainer)
VA 2
VA 2.5
VA 3
VA 4
VA 5
VA 6
VA 8
VA 10
VA 12
VA 14
VA 16
VA 18
VA 20
VA 22
VA 24
Model (w/
strainer)
VAS 2
VAS 2.5
VAS 3
VAS 4
VAS 5
VAS 6
VAS 8
VAS 10
VAS 12
VAS 14
VAS 16
VAS 18
VAS 20
VAS 22
VAS 24
Size
2
2-1/2"
3"
4"
5"
6"
8"
10"
12"
14"
16"
18"
20"
22"
24"
VA
70
180
250
300
550
910
1,850
3,550
4,700
6,000
8,000
10,000
12,000
14,000
17,000
psi/oF
VAS
70
160
220
300
500
425
1250
2000
2800
3350
3500
5200
7000
7750
8800
160/350
160/350
160/350
165/375
165/375
165/375
165/375
165/375
165/375
125/350
125/350
125/350
125/350
125/350
125/350
3
Normal piping layout for Vortex Air Separator in a
hot water boiler installation
ARMSTRONG VA VORTEX AIR SEPERATORS
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
79
ARMSTRONG PUMPS_______________________
FILE NO:
DATE:
SUPERSEDES:
DATE:
37.13
Mar. 20, 2005
New
New
Series DAS Dirt & Air Separator
Armstrong's line of Dirt & Air Separators (DAS) are designed to eliminate
entrained air and suspended dirt particles associated with the start-up
and maintenance of hydronic systems. The units incorporate a robust
stainless steel coalescing medium which directs dirt particles of all sizes
to the collection chamber at the bottom, and allows the air to be released
through an air vent at the top.
For applications with high pipe velocity and flow, Armstrong's DASH
(High Velocity) unit allows increased flow capacity for the same
connection size.
3
The DAS Series is available with either a welded or removable head,
both of which conform to ASME Section VIII, Div. 1. The welded head
design is also available, for a price reduction, as a non-ASME rated unit.
All models are available with NPT connections up to 4".
System Advantages
� Air and dirt removed with one unit
� Decreased corrosion, pump cavitation and wear of system
components
� Bypass/isolation valves, filters and other flow reducing components
eliminated
� Less maintenance
� Greater owner satisfaction
Unit Advantages
�
�
�
�
�
�
�
�
Robust stainless steel coalescing medium
ASME rated units as standard
High pressure units and larger than 12" connection sizes available upon request
Dirt particles can be flush and air vent cleaned/replaced during system operation
Minimal pressure drop with no fluctuations
Quiet operation
Faster air removal than vortex separators
Velocity independent air removal
Installation Schematics
Armstrong Dirt & Air Separators should be installed at the highest temperature and the lowest pressure points in the
system. Where this is not possible, the best location is at the point of highest temperature. Ideally, a separator should
be located on the outlet side of the boiler, and the suction side of the pump.
For Boiler Applications
80
For Chiller Applications
www.federalcorp.com
_______________________ARMSTRONG PUMPS
EXPANSION TANKS - STANDARD ASME PAINTED STEEL
Armstrong's tanks are constructed to the ASME Code for Unfired Pressure Vessels, Sec.
VIII. Tanks are furnished with gauge glass tappings.
Order No.
Special Order
AET12x51
AET14x48
AET14x63
AET16x72
AET20x62
Special Order
Special Order
Special Order
Model No. (including
tank size)
Size (gal.)
AET 12x33
AET 12x51
AET 14x48
AET 14x63
AET 16x72
AET 20x62
AET 20x78
AET 24x65
AET 24x72
15
24
30
40
60
80
100
120
135
3
EXPANSION TANKS - AX SERIES, PRECHARGED ASME
Armstrong's ASME precharged diaphragm and bladder type tanks separate the air and water within the tank, thus allowing
use of smaller tank, eliminating air from system rather than trying to control it, and improving system performance. Tanks
constructed to ASME code for 125 psi, max temp 240oF. Heavy duty butyl diaphragm inside of steel shell insure long life.
Other bladder and diaphram tanks are available from Armstrong. Please ask a salesperson for help.
VERTICAL MODELS
Order No.
Special Order
Special Order
Special Order
AX60V
AX80V
Special Order
Special Order
Model
AX-15V
AX-20V
AX-40V
AX-60V
AX-80V
AX-100V
AX-120V
Volume (USGal)
Tank
Acceptance
7.8
10.9
21.7
33.6
44.4
55.7
67.0
2.5
2.5
5.0
11.1
22.2
22.2
34.0
Order No.
Special Order
Special Order
Special Order
Special Order
Special Order
Special Order
Model
AX-144V
AX-180V
AX-200V
AX-240V
AX-260V
AX-280V
Volume (USGal)
Tank
Acceptance
77.0
90.7
110.7
131.7
159.0
211.0
34.0
34.0
34.0
44.4
56.0
84.0
HORIZONTAL MODELS
Order No.
Special Order
AX20
AX40
Special Order
Special Order
Special Order
Special Order
OKLAHOMA CITY
(800) 289-3331
•
•
Model
Volume (USGal)
Tank
Acceptance
AX-15
AX-20
AX-40
AX-60
AX-80
AX-100
AX-120
7.8
10.9
21.7
33.6
44.4
55.7
68.0
(405) 239-7301
FAX: (405) 232-5438
2.5
2.5
11.3
11.3
22.6
22.6
34.0
TULSA
(800) 955-1918
Order No.
Special Order
Special Order
Special Order
Special Order
Special Order
Special Order
•
•
Model
Volume (USGal)
Tank
Acceptance
AX-144
AX-180
AX-200
AX-240
AX-260
AX-280
77.0
90.0
110.0
132.0
159.0
211.0
(918) 249-1918
ARMSTRONG EXPANSION TANKS
FAX: (918) 249-9014
34.0
34.0
34.0
46.0
56.0
84.0
81
ARMSTRONG PUMPS_______________________
HEAT EXCHANGERS -- SHELL & TUBE
The Armstrong Shell and Tube heat exchanger is made in numerous configurations, from steam-to-water, water-to-water, and
tube bundle in tank. Applications include heating water in hydronic systems, heating or cooling various fluids from swimming
pools to industrial processes. Steel sheels, U-bend tube bundles from copper and other alloys, and various tube sheets are
available. Two and four pass construction from 4" to 36" shells are built to ASME Sec. VIII standards. Series WS Steam-towater heat exchangers stocked by Federal are illustrated here, but additional information can be obtained on all series. Stock
units have steel sheel, 3/4" OD copper tubes, & steel tube sheet.
Order No.
WS442
Model No.
WS-44-2
Description
2 Pass WS steam-to-water, 150
psi @ 375oF
Size (D x L) in.
4X48
Shell (steam) conn.
2" x 1" Thrd.
Tube (water) conn.
1-1/4" x 1-1/4" Thrd.
WS662
WS-66-2
2 Pass WS steam-to-water, 150
psi @ 375oF
6X72
3" x 1" Thrd.
2" x 2" Thrd.
WS872
WS-87-2
2 Pass WS steam-to-water, 150
psi @ 375oF
8X84
4" Flg x 1-1/4" Thrd.
3" x 3" Thrd.
3
Plate & Frame Heat Exchangers
The Armstrong plate and frame heat exchanger consists of a number of
specially corrugated metal plates assembled in a frame and bolted between
two pressure plates, one fixed and one adjustable. Turbulence is created in
the liquid flow channels, which creates very high heat transfer coefficients
and provides efficient heat transfer in a compact design. Armstrong plate and
frame heat exchangers are normally supplied with stainless steel plates. Titanium plates are available as an option.
Armstrong plate designs have been optimized for water-to-water heat transfer to provide enhanced performance in HVAC
applications.
Units are designed for 100 psi, 150 psi and 300 psi (690
kPa, 1034 kPa and 2068 kPa) designs. Applications requiring
higher working pressures can also be accommodated.
ABX Brazed Plate Heat Exchangers*
Armstrong offers brazed plate heat exchangers for refrigeration,
hydronic heating, and process temperature control applications.
The heat exchanger plates and connections are made from 316
stainless steel, to provide improved corrosion resistance. Standard
designs include copper brazed plates. Nickel brazing is available
as an option.
82
www.federalcorp.com
ARMSTRONG HEAT EXCHANG Shell & Tube
_______________________ARMSTRONG PUMPS
5000 COLUMN SUMP & SEWAGE PUMP SYSTEMS
Armstrong offers a complete range of high performance, easily maintained column type sump & sewage pumps. Built from the highest
quality engineered components, pumps can be supplied as replacement pumps or as part of a new installation. Armstrong systems are
available vertical motors (ODP, TEFC, or X-Proof), with control panel, level controls, and sump pit cover plate. View series from composite
curves, then ask Federal for a quote on your specific system requirements.
Sump Series 5200 & 5240 -- both light-duty and heavy-duty series are used in applications as varied as elevator pits, electrical tunnels,
loading docks, drain tiles, laundry facilities, floor drains and condensate returns. Simplex or duplex units are available. Multiple column
sections can be bolted together to accommodate custom sump depths. Both grease lubricated and water lubricated bearings are
available.
Sewage Series 5400 -- for building, municipal and industrial applications requiring top-quality long lasting product. Similar to
Series 5240, but with cast iron 2-vane open-type non-clog impeller.
NOTE: THESE ARE SPECIAL ORDER ONLY.
3
ARMSTRONG 5000 SERIES
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
83
ARMSTRONG PUMPS_______________________
3
The IVS Sensorless pump is designed
to meet the need for energy-efficient
pumping systems in today’s buildings.
Traditional smaller pumping systems,
up to and including 10 hp, incorporating fixed-speed pumps waste energy
through crude throttling valve flow
control. Lifetime Cost Analysis shows
that the capital cost of a fixed-speed
pump is typically only 5% of its lifetime cost.
Y Variable speed technology allows the speed of the pump to be tuned to suit sys-
tem demand.
YTechnological advancements make variable speed pumps attractive in terms of
both capital and lifetime cost.
YPressure transducers/sensors are no longer required, further reducing capital and installation cost.
YThe IVS Sensorless pump is a new generation pump, completely integrated into a
compact package.
YApplications for this technology include variable volume heating and chilled water
applications.
YGoes beyond ASHRAE 90.1 standards by adding value through varying pump
speed with 10 hp and lower motor sizes.
84
www.federalcorp.com
_______________________ARMSTRONG PUMPS
6000 SERIES HYDROPAK BOOSTER SYSTEMS
Quality booster systems at competitive prices, the Series 6000 Hydropak units perfectly fulfill requirements
of commercial, high rise, or industrial applications. Units are equipped with state of the art control systems
that provide uninterrupted, unattended pump operation in the most energy efficient way. Hydropak fully
factory assembled, tested and UL labeled units offer single source responsibility. Compact design minimizes
floor space, allowing up to 500 gpm models to fit through 34" doorways. Piping and headers are available in
various metals, with connections either flanged or grooved. Standard equipment includes isolation valves,
pilot operated pressure reducing valves, thermal bleed circuits, inlet and outlet pressure gauges, calibration
and testing, and factory mounting and painting of pumps, valves, piping and control panel on base. Custom
packages can include pressure tanks and custom pump controls. Contact Federal for a computer analysis
and proposal for your unique needs.
3
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
ARMSTRONG 6000 SERIES
85
ARMSTRONG PUMPS_______________________
SERIES 6800 VMSPak BOOSTER SYSTEMS
The ARMSTRONG VMSPak is available in three standard
arrangements with four different pump sizes to cover a broad
range of applications. When used with ARMSTRONG’S variable
speed controller, the VMSPak provides energy-efficient, automated pumping and allows the user to adjust pressure and
alarm settings with the touch of a button.
·
Available in standard configurations with up to 4 pumps
·
Available with jockey pumps or redundant (standby)
pumps
3
The new VMSPak Booster System is the latest addition to
the ARMSTRONG family of Pressure Booster Systems. Designed
to provide a reliable supply of domestic water, the ARMSTRONG
VMSPak is compact, energy-efficient and easy to install. Contractors and Building Owners will appreciate the small footprint.
Design Engineers will appreciate the versatility and range provided by the 12 available standard configurations. In addition to
the small footprint and energy-efficient design, the ARMSTRONG
VMSPak includes the following important features:

potable
86
Selection range charts for 2 to 4 pump systems
with equal pumps
Stainless Steel construction, suitable for
water applications

Available with constant speed control or variable
speed with microprocessor control

ASME or BS4814 rated hydro-accumulator

Compact “Knock-down” design

Efficient multistage pumps

Single-source responsibility for the complete packaged system

Pumps and complete package manufactured to
ARMSTRONG’S industry leading quality standards

Available with flanged or threaded system connections

Optional CSA, UL or CE rated controls

Factory performance tested and certified
www.federalcorp.com
_______________________ARMSTRONG PUMPS
6900 SERIES DualPak BOOSTER SYSTEM
Armstrong's DualPak offers the highest GPM per square foot of floorspace of
any duplex domestic water booster system available today! Ideal for hotels,
motels, resorts, condominiums, apartments, schools, office buildings,
retirement homes and hospitals. DualPak fits through 30" doorways, and takes
less than half the footprint of conventional systems. Units are lightweight,
allowing for ceiling suspension if desired. Using Armstrong's unique dualArm
pump (two pumps in one casing), DualPak systems cover flow ranges from 100 350 gpm, and pressure ranges between 20 and 100 psi. Available in 3 different
configurations to meet your requirements. All systems are factory tested at
simulated jobsite conditions prior to shipment from the factory, avoiding any
potential on-site problems. Request your proposal from Federal.
3
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
87
ARMSTRONG 6900 SERIES
ARMSTRONG PUMPS_______________________
SERIES 8100 ARMkool PACKAGED SYSTEMS
3
88
www.federalcorp.com
_______________________ARMSTRONG PUMPS
INTEGRATED PLANT PACKAGE-CHILLED WATER SYSTEM
3
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
89
ARMSTRONG PUMPS_______________________
9000 SERIES INTEGRATED PUMPING SYSTEMS
Armstrong's Integrated Pumping System (IPS) automatically ensures delivery of required pumping capacity to match
key building loads, while maintaining pumping energy costs at a minimum. With the use of system load detectors
(differential pressure sensors or temperature sensors), IPS automatically and continuously provides just the required
flow for the current needs in HVAC systems. The heart of the system is the PSM-9000 controller which can control as
many as 6 pumps in parallel, with up to 18 remote system load sensors in a closed loop system. Armstrong's DDC
precision control maintains the speed of all operating pumps to within +/- 5 rpm, maximizing energy cost reductions.
Dedicated or shared Variable Frequency Drives (VFDs) may be used, with or without power bypass systems. Pumps
may be operated as 100% standby or in a multiple pump staged parallel sequence. Armstrong offers the most
advanced IPS available, with the flexibility to meet the most demanding pumping applications. Request information
from your Federal sales person.
3
90
www.federalcorp.com
ARMSTRONG 9000 SERIES
_______________________ARMSTRONG PUMPS
HTP SERIES HEAT TRANSFER PACKAGES
A heat exchanger, utilizing steam or hot water as a heat
source, provides hot water or hot glycol for comfort or
process heating. The pumps circulate the heated water
throughout the hydronic system. An integral air separator
and expansion tank remove air and control system water
volume. The package is completely factory piped, assembled and tested.
Benefits




Single Source Responsibility
Simplified Selection
Compact Design
Ready to Install
HTP Features
Heat Exchanger (Shell and Tube or Plate and

Frame)






Pumps (Vertical or Horizontal style)
Expansion Tank
Air Separation
Flow Control
Piping and Valves
Assembly and Testing
Standard HTP Options






Armstrong Heat Transfer Packages are designed
for the Hydronic Heating of Schools, Hospitals, Office
Buildings, Apartments, Industrial Plants, Airport Terminals and Sports Centers. Other applications include
industrial process systems.
3
Electrical Controls
Variable Frequency Drives
Motors
Steam Trap
Steam Control Valve
Glycol Fill Connection
Custom HTP Options
Condensate Pumps

Custom HTP
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
91
BURKS PUMPS____________________________
3
92
www.federalcorp.com
____________________________BURKS PUMPS
3
As a master distributor, Federal stocks a broad line of Burks turbine pumps.
We can arrange quick factory shipments for all Burks pumps. Call for assistance.
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
93
BURKS PUMPS____________________________
3
CS SERIES CLOSE COUPLED TURBINE PUMPS
Regenerative type turbine pumps are designed to handle clear water and many other non-abrasive, lower viscosity liquids on high pressure, low capacity
applications with the greatest possible efficiency. The only turbine pump with Life-Lok ® External Impeller Adjustment feature that allows readjustment of
impeller without disturbing piping. The Standard Materials of Construction include: bronze fitted-cast iron frame and case; bronze (monel blades) impeller;
bronze raceway; #303 stainless steel shaft; carbon-ceramic stainless steel-Buna N shaft sleeve for temperatures to 225oF.
Capacity in GPM @ Total Head (PSI/Ft.)
Order No. Model No.
Description
HP
15CS6M 15CS6M PUMP TURB 11 1/2
1/2HP
Special
20CS6M PUMP BF TURB 2HP
2
Order
1/115/208/230
330CS7M 330CS7M PUMP TURB 3HP
3
3/60/208/230/46
RPM Phase
3450 SINGLE1
8.6/ 17.2/ 26/ 43.3/ 54.1/ 64.9/ 75.8/ 86.6 97.4/ 108.3/ 119.1 130/ 140.1/ 151.6
20 40 60 100 125 150 175 /200 225 250
/275 300 325 /350
16 15.2 15 13.5 12.8 12.4 12 11.5 11
10.7
-
3450 SINGLE1
16
15.2
15
13.5
12.8 12.4
3450 THREE2
21
19.6
20
17.3
16.5
16
12
11.5
11
15.3 14.7 14.2
10.7 10.5
10
9.7
9.5
13.7 13.3
13
12.5
12
Tappings: 1" discharge x 1 1/4" suction
1
115/205-230/1/60
2
208-230/460/3/60
REPAIR KITS 1
Order No.
B205225
B205226
B205227
B205229
1
Model No.
20522-5
20522-6
20522-7
20522-9
REPAIR PARTS
Description
KIT REP F/CS5M, ES5M
KIT REP F/CS6M/ES6M
KIT REP F/CS7M/ES7M
KIT REP F/CS9M/ES9M
Order No.
8991
9791
Model No.
8991
9791
Description
3/4" MECHANICAL SEAL
BUNA N O-RING
Kit includes impeller, raceway, shaft seal, "O" ring, suction sleeve,
impeller locknut, raceway screws, shaft key and instructions.
94
www.federalcorp.com
____________________________BURKS PUMPS
CT SERIES CLOSE COUPLED TURBINE PUMPS
Designed for pumping clear water and many other non-abrasive, lower viscosity liquids. Available in bronze fitted as standard.
Recommended for many applications requiring higher pressures and lower capacities. The standard 1-phase motors are 3450 RPM,
ODP construction. The Standard Bronze Fitted Materials of Construction include: cast iron frame and case; bronze (monel blades)
impeller; bronze raceway; #316 stainless steel shaft; carbon-ceramic shaft seal.
Capacity in GPM @ Total Head
Order No.
Model No.
Description
HP Voltage
Phase
8.6/20 43.3/100 86.6/200 130/300
Special Order 3CT5M
PUMP TURB 1/3HP 1/115/208/230 1/2 115/230V 1 PHASE 4.2 GPM 3.4 GPM 2.8 GPM 5CT6M
5CT6M
PUMP TURB 1/2HP 1/115/208/230 1/2 115/230V 1 PHASE 6.0 GPM 4.8 GPM 4.2 GPM 3.7 GPM
7CT7M
7CT7M
PUMP TURB 3/4HP 1/115/208/230 3/4 115/230V 1 PHASE 8.3 GPM 6.8 GPM 5.8 GPM 5.2 GPM
Tappings: 1" discharge x 1" suction
REPAIR KITS 1
Order No.
Special Order
B201586
B201587
1
Model No.
20158-5
20158-6
20158-7
REPAIR PARTS
Order No.
Model No.
8514
8514
9530
9530
8105
8105
Description
KIT REP CT5M/ET5M
KIT REP CT6M/ET6M
KIT REP CT7M/ET7M
Description
5/8" MECHANICAL SEAL
BUNA N O-RING
SLINGER WASHER
Kit includes impeller, raceway, shaft seal, "O" ring, impeller
EC & ED SERIES BASE MOUNTED TURBINE PUMPS
Designed for pumping any clean, non-corrosive, non-abrasive, lower viscosity liquids on low flow, high head applications.
They may be used for boiler feed, condensate return, heat transfer, jockey pump, hydraulic oil circulation, high pressure
spray, brine circulation and pressure boost. The adjusting screw in the power frame provides a means for external
adjustment of the clearance between the impeller and raceway to compensate for any possible wear between these parts.
Readjustment can be made without disassembling the pump or disturbing the piping. 1750 RPM. The Standard Materials
of Construction include: cast iron casing; cast iron (brass screen) strainer; bronze (monel blades) impeller; bronze raceway;
#303 stainless steel shaft; carbon-ceramic stainless steel-Buna N shaft sleeve for temperatures to 225oF.
Order No.
Model No.
Special EC7M GPM
BHP
Order
Special EC9M GPM
Order
BHP
EC10M
EC10M GPM
BHP
ED10M
ED10M GPM
BHP
ED12M
ED12M GPM
BHP
ED14M
ED14M GPM
BHP
Description
PUMP TURB BF
LESS BASE
PUMP TURB BF
LESS BASE
PUMP TURB BF
LESS BASE
PUMP TURB BF
LESS BASE
PUMP TURB BF
LESS BASE
PUMP TURB BF
LESS BASE
3
Capacity in GPM @ Total Head (PSI/Ft.)
8.6/20 17.2/40 26/60 43.3/100 54.1/125 64.9/150 75.8/175 86.6/200 97.4/225 108.3/250 119.1/275 130/300 140.1/325 151.6/350
20.9
19.9
19.1
17.7
16.8
16.0
15.3
14.5
13.8
13.1
12.4
11.8
11.2
10.7
0.65
0.75
0.85
1.1
1.2
1.4
1.6
1.7
1.9
2.1
2.2
2.4
2.6
2.7
29.2
27.7
26.3
24.0
22.5
21.3
20.0
18.8
17.7
16.5
15.3
14.3
13.3
12.2
0.73
0.86
1.0
1.4
1.6
1.9
2.1
2.4
2.6
2.9
3.2
3.4
3.7
4.0
35.3
33.1
31.3
28.3
26.5
25.0
23.5
22.1
20.7
19.4
18.0
16.7
15.5
14.3
1.0
1.2
1.4
1.9
2.2
2.5
2.7
3.0
3.3
3.6
3.9
4.2
4.6
4.9
52.5
48.6
46.2
43.0
41.2
39.4
37.5
36.7
34.0
32.1
30.0
28.5
26.7
24.8
2.0
2.3
2.5
2.9
3.2
3.6
3.9
4.3
4.6
5.0
5.3
5.7
6.1
6.4
73.2
69.4
66.0
61.0
58.6
56.4
54.1
52.2
50.3
48.5
46.7
45.0
43.4
41.7
2.5
2.8
3.3
4.1
4.5
5.0
5.6
6.0
6.5
7.0
7.3
7.8
8.3
8.7
91
85.8
81.5
75.0
71.3
68.0
65.0
62.0
59.2
56.3
53.5
51.0
48.5
46.0
4.1
4.4
4.8
5.8
6.4
7.1
7.7
8.3
9.0
9.6
10.3
11.0
11.7
12.3
The standard bronze fitted materials of construction consists of cast iron casing, cast iron (brass screen) strainer, bronze (monel blades) impeller, bronze
raceway, #303 stainless steel shaft, carbon-ceramic-S.S. - Buna N shaft seal for temperaures to 225 oF.
IMPELLER & RACEWAY REPAIR KITS 1
MECHANICAL SHAFT SEAL REPAIR KITS 2
Order No.
2170710
2171010
2171012
2171014
Order No.
21708
21711
Model No.
21707-10
21710-10
21710-12
21710-14
For
E22/E22M/EC10/EC10M
E25/E25M/ED10/ED10M
E27/E27M/ED12/ED12M
E29/E29M/ED14/ED14M
1
For E,EC, & ED Series Pumps. Kit includes impeller, raceway and
instructions.
REPLACEMENT PARTS FOR EC & ED SERIES
Description
Order No.
Special Order
IMPELLER/LOCKNUT
21332
SCREEN STRAINER FOR EC
SUCTION SLEEVE, BUNA N
SCREEN STRAINER FOR ED
SEAL MECH 3/4
SHAFT
BEARING SPRING
GASKET
2
For ECM & EDM Series Pumps. Kit includes impeller locknut,
shaft key, raceway screws, suction sleeve, shaft seal, case
gasket, housing gasket and instructions.
Replaced by EC (smaller) and ED (larger) series.
Description
OIL SEAL
GASKET
GASKET
BEARING
O-RING, BUNA N, FOR
STRAINER
21748A KEY-1/8"X5/8" SQ. ROD
21942 SEAL MECH 1-1/8
21333
21337
21473
21732
pumps
Order No. Model No.
4654A
4654A
5258
5258
5619
5619
5811
5811
7003
7003
8797
8797
pumps
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
Description
WASHER STUFF BOX
SCREW ADJUSTABLE REAR
GASKET
WASHER STUFF BOX
BOLT GLAND BRS (Large E Series)
MECH. SEAL 7/8" ((Small E Series)
MISCELLANEOUS PUMP AND TANK PARTS
Order No.
7323
7492A
9917
21271
22083
22063C
burks ec & ed series
pumps
For
ECM PUMPS
EDM PUMPS
PARTS FOR DISCONTINUED "E SERIES" PUMPS
Order No.
1407
4231
4646
8991
20921
21322
21328
Model No.
21708
21711
EC
Desi
They
spra
adju
Read
of Co
#30
TULSA
(800) 955-1918
•
•
Description
FLOAT SWITCH, DOUBLE POLE, NO OVERLOAD PROTECTION,
for use with horizontal receiver tanks.
WRENCH SPANNER 5/32 PIN
SEAL MECH 1-1/4
SEAL
MECH
burks
ct series
GASKET
burks ec & ed series
SLEEVE SHAFT BRZ
(918) 249-1918
FAX: (918) 249-9014
95
BARNES PUMPS___________________________
3
The Barnes family of pump products
provides versatility, high performance
and unequaled value. For more than
a century, design and specifying engineers, plumbing contractors and endusers including homeowners have
relied on Barnes Pumps for reliability
and durability. From mundane but essential applications like sewage and
wastewater to decorative fountain
pumps found in the town square,
Barnes Pumps delivers innovative,
cost-effective solutions with speed
and accuracy.
SERIES SE EFFLUENT PUMP
Submersible, non-clog sewage pump designed for typical raw sewage applications. Able to pump 2" solids. 2"
NPT, Female, Vertical. Wide-Angle, PVC, Mechanical level control. 15' Cord w/piggy-back plug.
Capacity: 100 gpm @ 8' TDH
50 gpm @ 17' TDH
25 gpm @ 23' TDH
Shut off head 25'
Order No.
SE411A
Model No.
SE411A
HP
0.4
VOLT/PH
115/1
Hz
60
RPM
1750
FULL
LOAD
AMPS
LOCKED
ROTOR
AMPS
CORD
SIZE
12.0
19.0
14/3
For more information go to www.cranepumps.com
96
www.federalcorp.com
______________________________LITTLE GIANT
AUTOMATIC CONDENSATE PUMPS
Vertical type pump unit, stainless steel shaft. Ideal for small flows as in HVAC evaporator condensate.
Gallons Per Hour @ Height
Power
Model
No.
Description
Volts
HP
Amp/Watt 1'
Order No.
3'
5' 7' 9' Shut off PSI Cord
"IN PAN"
1ABS
2ABS
1ABS
550520
PUMP,LESS PAN W/1/4" MPT CONN
551020 PUMP W/1/2 GAL PAN, 1/4" MPT CONN
115V
115V
1/150HP 1.1A/70W 205 180 145 1/40HP 1.7A/100W 300 255 205 160 105
10'
11.8'
4.3
5.1
6'
6'
ACCESSORIES
SPECIAL 599122 OVERFLOW SAFETY SWITCH, INSTALLS ON CONDENSATE PAN
ORDER
DUAL PURPOSE PUMP
May be used either totally submerged or in an open air closed line system
Gallons Per Hour @ Height
Order No.
Model No.
L2E38N 2E-38N 502203
Volts
HP Amp/Watt
115/1 1/40 1.7/100
1'
300
3'
255
5'
205
10'
70
Shut off
11.8'
Power
Cord
6'
PSI
5.1
3
WATER WIZARD® UTILITY PUMPS
This little workhorse includes garden hose adapter. Pumps down to 1/8" from surface. Epoxy coated cast aluminum housing, nylon
volute, SS shaft. Manual operation without RS5.
Gallons Per Hour @ Height
Power
Order
Model
No.
No.
Description
Volts HP Amp/Watt 1'
3'
5'
10' 15' 20' 22' Shut off PSI Cord
LITTLE GIANT WATER WIZARD® - SUBMERSIBLE
5MSP 505000 UTILITY PUMP LITTLE
115/11/6 HP 5A/380W 1200 1170 1100 1000 840 520 350 26.3' 11
10'
GIANT
599008 REMOTE LIQUID LEVEL 115/1 10
10'
RS51
SWITCH
5MSP
POTENT® PUMP SETS - NON-SUBMERSIBLE
Special PPS1
115/1 1/10 1.65/171 275
Order
-
-
225
-
165
-
-
-
6'
1
Converts a manual pump, up through 1/2 HP, to automatic operation. Attaches easily to the back of the Water Wizard. "ON" level 7 3/8" (+/- 3/8"). "OFF"
level 3/4" (+/- 3/8")
PPS1
BIG JOHN® SUMP PUMPS
For extended or continuous use in moving large volumes of water. Includes automatic liquid level switch.
LITTLE GIANT AUTO COND PUMP
8/1/2008
SPECIFICATIONS
Construction: Cast iron housing with protective epoxy coating, polypropylene base, polycarbonate cover, thermal overload
protection, screened intake, non-clog pumping head and impeller. For intermittent use, max temp of liquid 140 OF.
Order Model
No.
No.
Description
AUTOMATIC PUMPS1
6C1A 506158 AUTO SUMP PUMP, 1-1/2" DISC.
8C1A 508157 AUTO SUMP PUMP, 1-1/2" DISC.
1
Gallons Per Minute @ Height
Volts
HP
115/1 1/4
115/1 4/10
5'
10'
15'
20'
Shut off
PSI
Power
Cord
46
54
30
40
15
25
8
18'
22'
7.8
9.5
8'
10'
Pressure actuated On"-"Off" switch engages 7-10" water, and disengages in 1-3" of water.
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
• (918) 249-1918
(800)
955-1918
• FAX:
LITTLE
GIANT
DUAL PURPOSE
PUMP(918) 249-9014
6/17/2008
97
SKIDMORE PUMPS________________________
3
NOTE: Pump capacity 30 gpm at 20
psi discharge 3/4 hp. All boiler feed systems
simplex and duplex with make-up valve and
sight glass.
98
www.federalcorp.com
________________________SKIDMORE PUMPS
3
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
99
SKIDMORE PUMPS________________________
3
100
www.federalcorp.com
_________________________SKIDMORE PUMPS
PROTECTOR SERIES CONDENSATE RETURN/BOILER FEED UNITS
Packaged and completely assembled, wired and tested at the factory. Designed to provide maximum efficiency and easy
maintenance in a compact, space-saving configuration. Units have 1/3 HP ODP motors (115/230/1), 3500 RPM, capable of
pumping 18 GPM @ 20 PSI discharge.
Order No.
Model No.
CONDENSATE RETURN PUMPS
PC6N
PC6N 57412
PC15N
PC15N 57509
PC15DN
PC15DN 5751
PS10N
PS10N 5754
PS20DN
PS20DN 5756
BOILER FEED PUMPS
PSB71N
PSB71N 5760
PC6N
Condensate Return
Description
COND PUMP 1/3 SIMPLEX 115/230
COND PUMP 1/3 SIMPLEX 115/230
COND PUMP 1/3 DUPLEX 115/230
COND PUMP 1/3 SIMPLEX 115/230
COND PUMP 1/3 DUPLEX 115/230
Receiver
Size
Receiver
Material
Controls Std.
No. of
Pumps
6 gal.
15 gal.
15 gal.
10 gal.
20 gal.
C.I.
C.I.
C.I.
Steel
Steel
Float Switch
Float Switch
Mech. Alter.
Float Switch
Mech. Alter.
1
1
2
1
2
BOILER FEED PUMP 1/3 115/230
PARTS USED WITH PROTECTOR SERIES
Order No.
Model No.
Description
S504781
50478-1
VOLUTE GASKET PROTECTOR SERIES
51290
51290
GASKET, SEAL PLATE
53399
53399
BLANK OFF SUCTION PLATE
54049
54049
5/8 SEAL KIT PROTECTOR/10MX/VJSS/HJS
54766NS
54766-NS
PUMP/MTR ASSY 1/3 115/230 NO VOLUTE
56885
56885
IMPELLER (N) PROTECTOR
56887
56887
FLOAT SWITCH SIDE MTG (6 GAL AFTER 1991)
569481S
56948-1S
VOLUTE FLANGED
PSB Series
Boiler Feed
3
COMMON SKIDMORE PARTS
Order No.
FOR 10M SERIES
Special Order
Special Order
Model No.
50640
51724-1
52069
52069
54052
54052
Special Order
50205-1
Special Order
50206-1
MISCELLANEOUS SKIDMORE PARTS
Special Order
52068
10M Series
(Discontinued but
parts still available)
54055
Special Order
Special Order
54055
54058
57151
Description
PUMP & MTR ASSY 1/3 1/115/230
1/2 HP, 115/230V, 1 PH., 3,500 RPM MOTOR (ONLY). FOR CCVS & 10M
SERIES.
GSK KIT FOR 10M/CCVS
5/8S SEAL KT 10M/CCVS/VCSS/HCPS
MOTOR BRACKET W/GASKET FOR 10M/CCVS
PUMP HOUSING W/GASKET FOR 10M/CVS
SCREW STUDS AND NUTS KIT INCLUDES ITEMS 14, 24, 34 & 35 (PART
#14-A.)
7/8 SEAL KT VCSS/HP/HCPS/HSS/VES
1-1/8S TYPE SL KT VCSS/HCPS/HSS
CHECK VALVE DISC WITH GASKET (3 1/2" X 3/8" X 3/8"). FOR SIZES H & I
VACUUM PUMP (ITEM #59).
FLOAT SWITCHES
Mechanical switches and alternators designed to operate pumps in tanks or sumps.
Order No.
54500
9037EG9
9038AG1
9038DG8
9049EF-1
9049ER-3
Type AG1
Mechanical
Alternator,
Float Operated
OKLAHOMA CITY
(800) 289-3331
•
•
Model No.
54500
9037EG-9
9038 AG-1
9038DG-8
9049EF-1
9049ER-3
(405) 239-7301
FAX: (405) 232-5438
Description
FLOAT SWITCH ASSY (9037EG-9) W/FLOAT & ROD
FLOAT SWITCH LESS FLOAT & ROD
MECHANICAL ALTERNATOR, LESS FLOAT & ROD
MECHANICAL ALTERNATOR, LESS FLOAT & ROD
304 SS FLOAT
416 STAINLESS STEEL ROD
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
skidmore protector series pumps
101
VANTON PUMPS___________________________
3
102
www.federalcorp.com
___________________________VANTON PUMPS
3
OKLAHOMA CITY
(800) 289-3331
•
•
(405) 239-7301
FAX: (405) 232-5438
TULSA
(800) 955-1918
•
•
(918) 249-1918
FAX: (918) 249-9014
103
CONERY__________________________________
MERCURY SWITCHES
Designed for operating sump or sewage pumps to control liquid level in sumps. Can also be used
to operate alarms to indicate high or low water conditions in sumps or tanks. 2900 series wide
angle, internally weighted, (13 amp) 1/2 hp 120/240 VAC.
Order No.
2900WP10
2900WP20
2901WP20
Model No.
2900-B1S4P1-10
2900-B1S4P1-20
2901-B1S4P1-20
Description
10' CORD, Normally open switch
20' CORD, Normally open switch
20' CORD, Normally closed switch
NPS______________________________________
MECHANICAL SEALS/SEAL KITS
Order No.
3
104
FOR PACO PUMPS
K1001
K1051
K1061
14007083
Description
seal kit
seal kit
seal kit
seal
Order No.
MISC. SEALS
1012
185
185V
501
508
633
Description
seal
seal
seal
seal
seal
seal
www.federalcorp.com
conery mercury switches
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising