JVC EX-A10 User Guide Manual Operating Instruction Pdf

JVC EX-A10 User Guide Manual Operating Instruction Pdf
English
COMPACT COMPONENT SYSTEM
EX-A10
Consists of RX-EXA10, SP-EXA10 and XV-EXA10
INSTRUCTIONS
Downloaded From DvDPlayer-Manual.com JVC Manuals
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT1403-002B
[J, C, UJ]
Warnings, cautions and others
(For U.S.A.)
The lightning flash with arrowhead symbol, within
an equilateral triangle is intended to alert the
user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
(For U.S.A.)
(For U.S.A.)
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
(For U.S.A.)
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC which provides
guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
G-1
Downloaded From DvDPlayer-Manual.com JVC Manuals
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
CAUTION — F button!
Disconnect the mains plug to shut the power off completely (the
STANDBY lamp goes off).
The F button in any position does not disconnect the mains
line.
• When the system is on standby, the STANDBY lamp lights
red.
• When the system is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
ATTENTION - Touche F!
Déconnectez la fiche d’alimentation secteur pour couper l’alimentation complètement (le témoin STANDBY s’éteint).
La touche F, dans n’importe quelle position, ne déconnecte
pas le système du secteur.
• Quand le système est en attente, le témoin STANDBY est
allumé en rouge.
• Quand le système est sous tension, le témoin STANDBY
s’éteint.
L’alimentation ne peut pas être télécommandée.
CAUTION
• Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems must be
considered and local rules or laws governing the disposal of
these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping or
splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.
ATTENTION
• Ne bloquez pas les orifices ou les trous de ventilation.
(Si les orifices ou les trous de ventilation sont bloqués par un
journal un tissu, etc., la chaleur peut ne pas être évacuée
correctement de l’appareil.)
• Ne placez aucune source de flamme nue, telle qu’une bougie,
sur l’appareil.
• Lors de la mise au rebut des piles, veuillez prendre en
considération les problèmes de l’environnement et suivre
strictement les règles et les lois locales sur la mise au rebut
des piles.
• N’exposez pas cet appareil à la pluie, à l’humidité, à un
égouttement ou à des éclaboussures et ne placez pas des
objets remplis de liquide, tels qu’un vase, sur l’appareil.
Downloaded From DvDPlayer-Manual.com JVC Manuals
G-2
Warnings, cautions and others (continued)
(For U.S.A. or Canada models)
IMPORTANT FOR LASER PRODUCTS / IMPORTANT POUR PRODUITS LASER
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the
unit; leave all servicing to qualified service personnel.
3. CAUTION: VISIBLE AND / OR INVISIBLE CLASS 1M LASER RADIATION WHEN
OPEN. DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.
1. PRODUIT LASER CLASSE 1
2. ATTENTION: N'ouvrez pas le couvercle supérieur. Il n'y a aucune pièce réparable par
l'utilisateur à l'intérieur de l'appareil; confiez toute réparation à un personnel qualifié.
3. ATTENTION: RAYONNEMENT LASER VISIBLE ET / OU INVISIBLE DE CLASSE 1M
UNE FOIS OUVERT. NE PAS FIXER LE FAISCEAU NI REGARDER DIRECTEMENT
AVEC DES INSTRUMENTS OPTIQUES.
4. REPRODUCTION DE L'ÉTIQUETTE: ÉTIQUETTE DE PRÉCAUTION PLACÉE À
L'INTERIEUR DE L'APPAREIL.
(For models other than U.S.A. or Canada models)
IMPORTANT FOR LASER PRODUCTS / IMPORTANT POUR PRODUITS LASER
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the
unit; leave all servicing to qualified service personnel.
3. CAUTION: Visible and invisible laser radiation when open and interlock failed or
defeated. Avoid direct exposure to beam.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.
1. PRODUIT LASER CLASSE 1
2. ATTENTION: N'ouvrez pas le couvercle supérieur. Il n'y a aucune pièce réparable par
l'utilisateur à l'intérieur de l'appareil; confiez toute réparation à un personnel qualifié.
3. ATTENTION: Risque de radiations laser visible et invisible quand l'appareil est ouvert et
que le système de verrouillage ne fonctionne pas ou a été mis hors service. Évitez toute
exposition directe au rayon.
4. REPRODUCTION DE L'ÉTIQUETTE: ÉTIQUETTE DE PRÉCAUTION PLACÉE À
L'INTERIEUR DE L'APPAREIL.
G-3
Downloaded From DvDPlayer-Manual.com JVC Manuals
For Canada/pour le Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND.
For Canada/pour le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM
DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING EQUIPMENT STANDARD ENTITLED
“DIGITAL APPARATUS”, ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPLICABLES AUX
APPAREILS NUMIRIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR LE MATERIEL BROUILLEUR:
“APPAREILS NUMERIQUES”, NMB-003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS.
CAUTION — Proper Ventilation
To avoid risk of electric shock and fire and to protect from damage, locate the apparatus as follows:
Top/Front/Back/Sides: No obstructions should be placed in the areas shown by the dimensions below.
Bottom:
Place on the level surface. Maintain adequate air path for ventilation by placing on
a stand with a height of 10 cm (3 1516 ″) more.
In addition, maintain the best possible air circulation.
Attention: Ventilation correcte
Pour éviter tout risque d’électrocution et d’incendie, et pour ne pas endommager les appareils, placez-les
de la façon suivante:
Faces supérieure /avant / arrière / côtés : Aucune obstruction ne doit se trouver dans les zones
indiquées par les dimensions ci-dessous.
Bas :
Placez l’appareil sur une surface plane. Maintenez une entrée
d’air adéquate pour la ventilation en plaçant l’appareil sur un
support avec une hauteur d’au moins 10 cm (3 1516 ″).
De plus, maintenez la meilleure circulation d’air possible.
Front view
Vue avant
15 cm
(5 15 16 ″)
Side view
Vue de côté
1 cm
( 7 16 ″)
1 cm
( 7 16 ″)
15 cm
(5 15 16 ″)
15 cm
(515 16 ″)
15 cm (5 15 16 ″)
Front
Avant
Wall or
obstructions
Mur, ou
obstruction
10 cm
(3 15 16 ″)
[European Union only]
[Union européenne seulement]
Downloaded From DvDPlayer-Manual.com JVC Manuals
G-4
Table of contents
Introduction
Playing back DVDs/CDs
Supplied accessories ......................................2
Part description ...............................................3
Basic operations of the DVD player ..............20
DVD player ......................................................... 3
Receiver.............................................................. 4
Using the remote control .................................5
Inserting batteries into the remote control .......... 5
Operating the TV using the remote control......... 6
Preparation
Connections ....................................................7
Standard setup ................................................... 7
Connecting the antennas.................................... 7
Connecting the speakers .................................... 9
Connecting the receiver and the DVD player ... 10
Connecting other equipment............................. 11
Connecting a TV ............................................... 12
Connecting the power cords ............................. 13
Basic operations
Basic operations............................................14
Turning on/off the system ................................. 14
Setting the clock ............................................... 15
Dimmer ............................................................. 16
Adjusting the volume ........................................ 16
Turning off the sound temporarily (MUTING) ... 16
Adjusting the sound quality............................... 16
Adjusting the bass sound.................................. 17
Enhancing the playback sound
(CC CONVERTER) ........................................ 17
Listening to radio
Listening to radio broadcasts ........................18
Setting the AM tuner spacing (only for
models sold at post exchanges)..................... 18
Selecting a radio station ................................... 18
Tuning in to a preset radio station .................... 19
1
Downloaded From DvDPlayer-Manual.com JVC Manuals
Playing back a DVD/CD ....................................20
Changing the display in the display window ......23
Selecting a chapter/track using the number
buttons ............................................................23
Stopping playback .............................................23
Pausing playback ..............................................24
Advancing the picture frame by frame...............24
Fast reverse/fast forward search .......................24
Playing back from a position 10 seconds before
(One touch replay) ..........................................25
Slow motion playback........................................25
Skipping to the beginning of a chapter/
track/file...........................................................25
Skipping at about 5 minute intervals..................26
Resuming playback ...........................................26
Selecting a track from the menu screen ............27
Convenient functions of the DVD player .......28
Locking DVD/CD ejection ..................................28
Playing back a DVD/CD in the desired order
(Program playback).........................................28
Playing back a DVD/CD in a random order
(Random playback) .........................................30
Playing back a DVD/CD repeatedly
(Repeat playback) ...........................................30
Playing back a specified part repeatedly
(A-B repeat playback) .....................................31
Saving the playback settings for next time ........31
Selecting the subtitles........................................32
Selecting the audio language ............................32
Selecting the view angle....................................33
Magnifying the picture (ZOOM) .........................33
Adjusting the picture quality (VFP) ....................34
Playing back the bonus group ...........................34
Browsable still pictures (B.S.P.) ........................35
Creating realistic sound (3D PHONIC) ..............35
Using the status bar and the menu bar .............36
Changing the initial settings with the
preference screen .....................................38
Basic operations ................................................38
LANGUAGE.......................................................38
PICTURE...........................................................39
AUDIO ...............................................................39
OTHERS............................................................39
Listening to the sound of other
audio equipment
Listening to the sound of other audio
equipment ...................................................41
Timer
Timer .............................................................42
Using the sleep timer ........................................ 42
Using the playback timer .................................. 43
Reference
Using the AV COMPU LINK function ............45
Connection and setup....................................... 45
Operation .......................................................... 45
Special cautions ............................................46
Notes on handling............................................. 46
About DVDs/CDs...........................................47
Playable DVD/CD types.................................... 47
Disc structure.................................................... 49
Troubleshooting.............................................50
Language codes............................................51
Specifications ................................................52
Check to be sure you have all of the supplied
accessories.
The number in parentheses is the quantity of the
items supplied. If anything is missing, contact your
dealer immediately.
•
•
•
•
•
•
•
•
•
•
Remote control (1)
Batteries (2)
FM antenna (1)
AM loop antenna (1)
Speaker cords (4)
Audio cord (1)
Optical digital cord (1)
Synchronization cord (1)
Composite video cord (1)
AC plug adaptor* (2)
Introduction
Supplied accessories
Introduction
NOTE
* The AC plug adaptor is not supplied for U.S.A. and
Canada models.
CAUTION
• Do not fold the optical digital cord as this may
damage the inner wire.
How to read this manual
• This manual explains the operations assuming
that you will use the remote control. Some buttons
on the receiver or the DVD player are the same as
those on the remote control. You can use either
button in this case.
• Some diagrams in this manual are simplified or
exaggerated for the purpose of explanation.
• You can operate some functions differently from
the explanation given in this manual.
• The following marks refer to the usable discs for
the explained function.
• “DVD VR” means a DVD recorded in DVD Video
Recording (DVD VR) format.
• “VCD” stands for “Video Compact Disc”.
• “SVCD” stands for “Super Video Compact Disc”.
• An “ASF” disc means a disc recorded in
“Advanced Systems Format”.
Downloaded From DvDPlayer-Manual.com JVC Manuals
2
Part description
The numbers refer to the pages in which the parts are explained.
DVD player
Front panel
See “Display window” shown below.
5
23–26, 28
13, 14
14
20
20, 28 20, 24
Rear panel
45
10
10
47
12
12
10
12
13
Display window
The receiver and the DVD player use the same design for their display windows.
21, 22
34, 35
13
21, 22
21, 27
21, 22, 29
3
28 30
21, 22, 29
Downloaded From DvDPlayer-Manual.com JVC Manuals
30
31
31
Introduction
The numbers refer to the pages in which the parts are explained.
Receiver
Front panel
See “Display window” shown below.
18
5
13, 14
14, 18
16
*
17
18, 20, 41
* This terminal is for connecting a pair of headphones equipped with a stereo plug (not supplied). When the
headphones are connected, the speakers do not produce any sound.
Rear panel
12
10
10
9, 11
10
7
11
12
8
13
Display window
The receiver and the DVD player use the same design for their display windows.
15, 18
18
Downloaded From DvDPlayer-Manual.com JVC Manuals
43
42
4
Using the remote control
The numbers refer to the pages in which the parts
are explained.
14
16
23
Inserting batteries into
the remote control
6, 14
20
14
18
21, 25, 34
41
20
6
6
24, 25
24, 25
23
27
27, 32
17
6
6
16
16
24, 25
20
24, 25
24
27
15, 21,
27, 36
Batteries (2)
25
36
32
32
38
33
22
34
6, 15, 23
35
33
28, 30
30
15, 31, 43
15, 43
18
19
35
42
13
15, 29, 44
11
16
16
11, 17
If the effective distance between the remote control
and remote control sensor on the receiver or the
DVD player decreases, replace the batteries. Use
two R6P (SUM-3)/AA(15F) type dry-cell batteries.
CAUTION
• Do not use a used battery and a new battery
together.
• Do not use different types of batteries at the
same time.
• Take out the batteries if the remote control is not
to be used for a long time. Otherwise it may
cause a leakage.
Remote control operation
When operating the remote control, point it at the
front panel of the receiver or the DVD player. If the
remote control is operated from a direction that is
extremely oblique or when there is an obstacle in
the way, signals may not be transmitted.
If the remote control sensor is exposed to a strong
light such as direct sunlight, correct operation may
not be carried out.
5
Downloaded From DvDPlayer-Manual.com JVC Manuals
You can operate your TV using the remote control
of this system.
Remote control
mode selector
F TV
TV/VIDEO
TV
CHANNEL
TV
VOLUME
Manufacturer
Code
Manufacturer
Code
JVC
01
Samsung
12
Hitachi
10
Sanyo
13
Magnavox
02
Sharp
06
Mitsubishi
03
Sony
07
Panasonic
04, 11
Toshiba
08
Philips
14
Zenith
09
RCA
05
Introduction
Operating the TV using
the remote control
NOTE
• A manufacturer code is subject to change without
notice. You may not be able to operate the TV
produced by the manufacturer.
5
Release F TV.
Using the remote control for the TV operation
Operate the remote control by pointing it at the TV.
ENTER
Turns on/off the TV.
Changes the channels.
Number
buttons
Adjusts the volume.
~
Setting the manufacturer code
1
2
/
Slide the remote control
mode selector to TV.
*1
Hold down F TV.
Switches the
previously selected
channel and the
current channel.
Switches the TV and video input.
• Hold down F TV until you finish step 4.
3
4
Selects the channels.
/
Press ENTER and release.
*1 Make sure to slide the remote control mode
selector to TV in advance.
Press number buttons (1-9, 0).
NOTE
• Refer to “Using the number buttons”
(A page 15).
• After replacing the batteries of the remote control,
set the manufacturer code again.
• When the remote control mode selector is slid to TV,
some buttons may not work.
Examples:
For a Hitachi TV: Press 1, then 0.
For a Toshiba TV: Press 0, then 8.
When the manufacturer of your TV has two or
more codes, select the manufacturer codes in turn
and find the one that operates the TV and the
remote control properly.
Downloaded From DvDPlayer-Manual.com JVC Manuals
6
Preparation
Connections
Do not turn on the power until you complete the connection.
Standard setup
DVD player
Speaker
Receiver
Speaker
Connecting the antennas
Connecting the AM loop antenna (supplied)
1 Set up the AM loop antenna.
3 Turn the AM loop antenna to find the best
position for radio reception.
Place the AM loop antenna as far from the
receiver as possible.
• Do not place the AM loop antenna on a metallic
table or close to a TV, computer, or other electric
appliances. Doing so may affect radio reception.
7 When radio reception with the supplied AM
loop antenna is poor
Electric wire: 3 - 5 m (9 ′ 10″ - 16 ′ 5″) (not supplied)
2 Connect the antenna cord.
Twist
together
electric
wire and
the AM
Electric
loop
wire
antenna
cord.
Receiver
(rear panel)
White
Black
AM loop
antenna cord
Connect the ends of the
antenna cord as shown
above.
If insulation covers
the tips of the
antenna cord,
twist and pull off
the insulation.
Stretch out the electric
wire horizontally,
preferably in a high
place such as above a
window or outdoors.
Connect the AM loop
antenna cord to the
receiver together with
the electric wire.
Receiver
(rear panel)
When positioning the antennas, find the best
position for reception while listening to an actual
radio program (refer to “Listening to radio
broadcasts” (A page 18)).
7
Downloaded From DvDPlayer-Manual.com JVC Manuals
7 When radio reception with the supplied FM
antenna is poor, or when using a communal
antenna
FM antenna
Antenna cord
(not supplied)
or
Receiver
(rear panel)
Stretch out the FM antenna to the best position for
radio reception, and then fix the FM antenna with
adhesive tape.
Communal
antenna terminal
Receiver
(rear panel)
Converter (not
supplied: compatible
with 300 C/75 C)
Preparation
Connecting the FM antenna (supplied)
Outdoor FM
antenna
(not supplied)
Coaxial cord
(not supplied)
Depending on the radio reception
conditions, an FM feeder antenna
(not supplied: compatible with
300 C) can be used. In this case, a
converter (not supplied) is required.
When using an antenna other than those supplied
with this system, refer to the operation manuals for
the antenna and converter for details of connection.
Receiver
Downloaded From DvDPlayer-Manual.com JVC Manuals
When positioning the antennas, find the best
position for reception while listening to an actual
radio program (refer to “Listening to radio
broadcasts” (A page 18)).
8
Connections (continued)
Do not turn on the power until you complete the connection.
Connecting the speakers
There is no difference between the left and right speakers.
Speaker terminal
Before
connecting the
speaker cords,
twist and pull off
the insulation.
Speaker cord
Speaker terminal
Speaker cord
TWEETER
RIGHT
TWEETER
RIGHT
TWEETER
LEFT
TWEETER
LEFT
WOOFER
RIGHT
WOOFER
RIGHT
WOOFER
LEFT
WOOFER
LEFT
TWEETER
WOOFER
TWEETER
Speaker cords
(supplied)
WOOFER
Receiver (rear panel)
Right speaker
(rear panel)
Left speaker
(rear panel)
• An incorrect connection may damage the speakers.
• The supplied speakers are dedicated to the supplied receiver as parts of the EX-A10 system. Do not
connect the supplied speakers to equipment other than the supplied receiver. Doing so may damage the
speakers.
CAUTION
• Do not short-circuit the ª and · speaker
terminals. Doing so may damage the receiver.
• Do not connect other speakers together with the
supplied speakers. The change in impedance
may damage the receiver and the speakers.
• Improper speaker cord connection spoils the
stereo effect and sound quality.
• The supplied speakers are magnetically
shielded, but color irregularity may occur on the
TV depending on some conditions. To prevent
color irregularity, set up the speakers following
the instructions below.
1. Turn off the main power of the TV before
setting up the speakers.
2. Place the speakers enough distance from the
TV so that they do not cause color irregularity
on the TV.
3. Wait for about 30 minutes before turning on
the main power of the TV again.
9
Downloaded From DvDPlayer-Manual.com JVC Manuals
The speakers employ natural wood for the
diaphragm and the cabinet in order to
reproduce the original sound faithfully.
The appearance will therefore be different for
each system.
You can detach the speaker cover.
Speaker
cover
NOTE
• To allow the receiver and the DVD player to emit
generated heat, leave a space of at least 1 cm
( 716 ″ ) between the receiver or the DVD player and
the speakers or other objects.
Make sure to connect the three supplied cords.
Preparation
Connecting the receiver and the DVD player
DVD player (rear panel)
Synchronization
cord (supplied)
Optical digital
cord (supplied)
CAUTION
• Do not fold the optical digital cord as this may
damage the inner wire.
Audio cord
(supplied)
If protection caps cover the tips of the optical
digital cord, pull off the protection caps before
connecting.
Protection cap
Downloaded From DvDPlayer-Manual.com JVC Manuals
10
Connections (continued)
Do not turn on the power until you complete the connection.
Connecting other equipment
Connecting other speakers
Remote control
mode selector
To connect speakers other than the ones supplied,
follow the operations shown below.
1
2
7
2 /3 (cursor)/
ENTER
3
BASS
ADJUST
Connect the speakers to the
SPEAKERS WOOFER LEFT and
RIGHT terminals on the
receiver.
Hold down BASS ADJUST for 2
or more seconds.
SCAN MODE
• “Single Amp” is displayed in the display
window on the receiver, and no audio signal
is sent to the SPEAKERS TWEETER LEFT
and RIGHT terminals.
S. WFR OUT
Display on the receiver
Connecting the subwoofer
NOTE
When you connect this system with an amplifierbuilt-in subwoofer (not supplied), you can enjoy a
more dynamic bass sound. Refer to the manual of
the subwoofer for details.
Audio cord (not supplied)
(If an audio cord comes with the amplifier-built-in
subwoofer, you can use the audio cord.)
Amplifier-built-in subwoofer
(not supplied)
Receiver
(rear panel)
To produce sound from the subwoofer, press
S.WFR OUT on the remote control to display
“S. WOOFER ON” (Subwoofer on) in the display
window on the receiver. Each time you press
S.WFR OUT, the display toggles between
“S. WOOFER ON” and “S. WOOFER OFF”.
NOTE
• When “S. WOOFER ON” is selected, bass sound
from the left and right speakers will be automatically
turned down and the bass sound will be emitted
mainly from the subwoofer.
11
Slide the remote control
mode selector to
RECEIVER.
Downloaded From DvDPlayer-Manual.com JVC Manuals
• The impedance of speakers connected to this
system must be within the range 6 C to 16 C.
• When connecting the supplied speakers to the
receiver, hold down BASS ADJUST on the remote
control for 2 or more seconds once again to select
“Bi-Amp” in the display window on the receiver.
Connecting other audio equipment
Connecting a TV with the VIDEO terminal
TV
Output
Preparation
Connecting a TV
DVD player
(rear panel)
Other audio
equipment
To video terminal
Audio cord
(not supplied)
Composite video cord (supplied)
Connecting a TV with the S-VIDEO
terminal
TV
DVD player
(rear panel)
Input
Receiver (rear panel)
To S-video terminal
Connecting digital equipment with an
optical output terminal
Output
MD player or satellite
receiver
To an optical digital output
terminal
S-video cord (not supplied)
Connecting a TV with the COMPONENT
VIDEO OUT terminals
TV
Optical digital cord
(not supplied)
DVD player
(rear panel)
To component terminals
Input
Receiver (rear panel)
Component video cord (not supplied)
Downloaded From DvDPlayer-Manual.com JVC Manuals
12
Connections (continued)
Do not turn on the power until you
complete the connection.
After connecting the DVD player to the TV, select
the video signal type correctly according to the TV.
1
2
3
Slide the remote control
mode selector to DVD.
Make sure that playback stops.
(If a disc is being played back,
press 7 to stop playback.)
Press SCAN MODE.
For the locations of the remote
control buttons, refer to page 11.
CAUTION
• Do not connect an S-video cord and a
component video cord at the same time.
Otherwise pictures may not be played back
properly.
• Connect the DVD player directly to a TV (or a
monitor) without routing through a video
cassette recorder (VCR). Otherwise picture
distortion may occur during playback.
TV (or
monitor)
DVD player
• The current video signal type will flash.
4
Press 2, 3 (cursor) to select
the video signal type suitable
for the TV.
• You can select “INTERLACE” or
“PROGRESSIVE”. You can obtain better
picture quality in the “PROGRESSIVE”
mode than in the “INTERLACE” mode.
When you select “INTERLACE”, the image
is displayed alternating between half of the
scanned lines in the “PROGRESSIVE”
mode and the other half of the scanned
lines. The way of displaying the image is a
conventional video signal type.
• Select “INTERLACE” when a TV only
compatible with interlaced video signals is
connected to the DVD player.
• Select “PROGRESSIVE” when a TV
equipped with a component terminal and
compatible with progressive video signals is
connected to the DVD player. When you
select “PROGRESSIVE”, the image is
displayed with all scanned lines at the same
time. The image has a higher resolution
than that in the “INTERLACE” mode.
5
• Connecting the DVD player to a VCR-built-in-TV
may also cause picture distortion during
playback.
Connecting the power cords
Receiver
AC outlet
Receiver
(rear panel)
DVD player
AC outlet
DVD player
(rear panel)
Press ENTER.
• The selected video signal type is displayed
for a short time.
NOTE
• Although the picture may be distorted when you
press ENTER, this is not a malfunction of the
system.
• There are some progressive TVs and high-definition
TVs that are not fully compatible with this system,
resulting in an unnatural picture when playing back
a DVD VIDEO with progressive scanning. In this
case, change the scan mode to “INTERLACE”.
• To check the compatibility of your TV, contact your
local JVC customer service center.
• All JVC-manufactured progressive TVs and highdefinition TVs are fully compatible with this system.
• Even if the power cord of the DVD player is
disconnected from the AC outlet or the power is
interrupted, the video signal type setting is stored.
13
Direct connection
Downloaded From DvDPlayer-Manual.com JVC Manuals
• Connect the power cords after you complete the
other connections.
• The STANDBY lamps on the front panels of the
receiver and the DVD player will light up.
Basic operations
Basic operations
DIMMER
Remote control
mode selector
DISPLAY
F AUDIO
0 OPEN/
CLOSE
FM/AM
CC
CONVERTER
F DVD
AUX
MUTING
AUDIO
VOLUME +/ –
Turning on/off the system
Receiver
1
2
8
• The power of the receiver will turn on and
the STANDBY lamp on the receiver will turn
off.
• Press F AUDIO again to turn off the
power of the receiver.
• With the power off, pressing any of the
following buttons also turns on the receiver.
- DVD, FM/AM or AUX on the remote
control
- 3/8 on the DVD player
The function assigned to the button starts
working at the same time.
5///2/3
(cursor)/
ENTER
Number
buttons
CLOCK/
TIMER
SET
BASS +/ –
Slide the remote control
mode selector to
RECEIVER.
Press F AUDIO (or F on the
receiver).
CANCEL
BASS
ADJUST
Preparation/Basic operations
•
DVD player
TREBLE +/ –
1
2
Slide the remote control
mode selector to DVD.
Press F DVD (or F on the DVD
player).
• The power of the DVD player will turn on
and the STANDBY lamp on the DVD player
will turn off.
• Press F DVD again to turn off the power
of the DVD player.
• With the power off, pressing any of the
following buttons also turns on the DVD
player.
- DVD or 0 OPEN/CLOSE on the remote
control
- 0 or 3/8 on the DVD player
The function assigned to the button starts
working at the same time.
(When you press DVD on the remote
control or 3/8 on the DVD player, if a disc
has been loaded, playback starts
automatically.)
Downloaded From DvDPlayer-Manual.com JVC Manuals
14
Basic operations (continued)
Setting the clock
You can set the clock when the receiver is turned
either on or off.
Example:
To set the clock to 10:30 a.m. on Wednesday
1
2
Slide the remote control
mode selector to
RECEIVER.
Press CLOCK/TIMER.
Example:
Display on the receiver (for U.S.A. or Canada models)
8
Press SET.
• The clock starts from 0 seconds in the
minute you set.
NOTE
• While setting the clock, you can return to the
previous step by pressing CANCEL.
• For U.S.A. or Canada models, the time display on
the receiver is a 12-hour clock.
• For models sold at post exchanges, the time display
on the receiver is a 24-hour clock.
• The clock will gain or lose about 1 minute per month.
• If the power cord of the receiver is disconnected
from the AC outlet or the power is interrupted, the
clock setting is stored for about 1 minute.
• You cannot set the clock when “DISPLAY OFF” is
selected. (A page 16)
Adjusting the clock
3
Press 2 or 3 (cursor) to select
the hour.
• Hold down the button to incrementally
increase the hour setting.
• You can also use the number buttons to
specify the hour. Refer to “Using the
number buttons” shown on the right.
AM
4
Press SET.
Press CLOCK/TIMER twice to
display the clock, and then adjust
the clock starting from step 3.
Displaying the clock when using the
receiver
Press DISPLAY.
• Refer to “Changing the display in the display
window”. (A page 23)
AM
5
6
7
Press 2 or 3 (cursor) to select
the minute.
• Hold down the button to incrementally
increase the minute setting.
• You can also use the number buttons to
specify the minute.
Press SET.
Press 2 or 3 (cursor) to select
the day of the week.
• Hold down the button to change the setting
for the day of the week.
AM
• Abbreviations are used for the days of the week.
Sun. → Sunday
Mon.→ Monday
Tue. → Tuesday
Wed.→ Wednesday
Thu. → Thursday
Fri. → Friday
Sat. → Saturday
15
Downloaded From DvDPlayer-Manual.com JVC Manuals
Using the number buttons
Examples:
5:
15:
→
→
150:
→
→
→
→
Dimmer
Adjusting the volume
Changing the brightness of the display
windows on the receiver and the DVD
player
1
You can set the brightness of the display windows
on the receiver and the DVD player respectively.
2
2
Slide the remote control mode
selector to RECEIVER or DVD.
Press DIMMER repeatedly.
Turning off the sound
temporarily (MUTING)
1
• Each time you press DIMMER, the setting
changes on the receiver/DVD player.
DIMMER 1
DIMMER 2
DIMMER OFF
DIMMER AUTO
• For a disc containing video, when you
select “DIMMER AUTO”, “DIMMER 2” is
automatically selected during video
playback and is canceled when the
playback stops.
• For a disc containing no video, when you
select “DIMMER AUTO”, “DIMMER OFF” is
automatically selected during playback and
is canceled when the playback stops.
Turning off the display on the receiver
You can also turn off the display on the receiver
when the receiver is turned off.
7 When the receiver is turned off
1
2
Slide the remote control
mode selector to
RECEIVER.
Press AUDIO VOLUME +/–.
• The volume can also be adjusted by turning
the VOLUME control on the receiver.
7 When the receiver/DVD player is turned on
1
Slide the remote control
mode selector to
RECEIVER.
Basic operations
For the locations of the remote
control buttons, refer to page 14.
2
Slide the remote control
mode selector to
RECEIVER.
Press MUTING.
• No sound will come out from the speakers,
headphones and the subwoofer.
• Press MUTING again to restore the sound.
When the power is turned off once and
turned on again, the sound will also be
restored.
Adjusting the sound quality
1
2
Slide the remote control
mode selector to
RECEIVER.
Bass: Press BASS +/–.
Treble: Press TREBLE +/–.
Press DIMMER repeatedly.
• Each time you press DIMMER, the setting
changes on the receiver.
DISPLAY ON
DISPLAY OFF
Downloaded From DvDPlayer-Manual.com JVC Manuals
16
For the locations of the remote
control buttons, refer to page 14.
Basic operations (continued)
Adjusting the bass sound
1
2
Slide the remote control
mode selector to
RECEIVER.
Press BASS ADJUST.
Display on the receiver
3
While the selectable values are
flashing, press 2 or 3 (cursor)
to select the value of the bass
frequency.
• You can select “100 Hz”, “120 Hz” or
“140 Hz”.
• The initial setting is “100 Hz”. Select the
value for your desired bass sound.
4
While the selectable values are
flashing, press 5 or / (cursor)
to select the value of “Q” in the
display window.
• You can select “0.75”, “1” or “1.25”.
• The initial setting is “1”. Select the value for
your desired bass sound.
5
Press ENTER.
Enhancing the playback
sound (CC CONVERTER)
The CC CONVERTER function is designed to
provide natural sound by improving the playback
sound from low-bit-rate digital sources.
The function compensates for sound waves
dissipated during digital recording compression to
approximate the original analog sound. Sound is
reproduced with more bits (24 bit) and a wider
range of frequency (128 kHz, 176.4 kHz or
192 kHz).
1
2
Slide the remote control
mode selector to
RECEIVER.
Press CC CONVERTER.
• When the CC CONVERTER function is
activated, the CC CONVERTER lamp
(button) on the front panel of the receiver
lights up.
• Each time you press CC CONVERTER, the
display changes as follows.
- “CC CNVRTR 1”:
Plays back a digital source with noncompressed sound signals (linear PCM).
- “CC CNVRTR 2”:
Plays back a digital source with
compressed sound signals (Dolby digital,
DTS, MP3 or WMA).
- “CC CNVRTR OFF”:
Cancels the CC CONVERTER function.
• The selected values are displayed for a
short time.
CC CONVERTER lamp (button)
NOTE
• The adjustment of the bass sound does not change
the treble and bass sound level adjustments.
Receiver
NOTE
• The initial setting is “CC CNVRTR 1”.
• The CC CONVERTER function does not work when
analog sound is selected as the sound source or
when 3D PHONIC is activated (A page 35). In such
cases, pressing CC CONVERTER only displays
“ANALOG SOURCE ”.
• The original range of frequency is automatically
detected and extended to a specific range.
When the original range is 32 kHz, 44.1 kHz or
48 kHz, the range is extended to 128 kHz,
176.4 kHz or 192 kHz respectively.
17
Downloaded From DvDPlayer-Manual.com JVC Manuals
Listening to radio
Selecting a radio station
Remote control
mode selector
FM/AM
This receiver can receive FM and AM radio
broadcasts.
1
TUNING / /
PRESET / /
ENTER
2
MEMORY
Setting the AM tuner
spacing (only for models
sold at post exchanges)
Some countries space AM stations 9 kHz apart,
and other countries use 10 kHz spacing.
If you purchased the system at a post exchange,
select either spacing according to the country
where you will use the system. This function is not
designed for U.S.A. and Canada models.
On the receiver ONLY:
SEARCH –
SEARCH +
Receiver
7 When the receiver is turned off
To select 10 kHz spacing, while holding down
SEARCH + on the receiver, press F on the
receiver to turn on the power. “AM 10 kHz
STEP” appears in the display window.
To select 9 kHz spacing, while holding down
SEARCH – on the receiver, press F on the
receiver to turn on the power. “AM 9 kHz
STEP” appears in the display window.
Press FM/AM to select “FM” or
“AM”.
• Pressing FM/AM selects a radio broadcast
as the sound source.
• You can also use SOURCE SELECT on the
receiver to select a radio broadcast as the
sound source.
• Each time you press FM/AM, the band will
toggle between “FM” and “AM”.
Example:
Display on the receiver for U.S.A. or Canada
models
Number
buttons
FM MODE
Slide the remote control
mode selector to
RECEIVER.
Basic operations/Listening to radio
Listening to radio broadcasts
Frequency
3
Press TUNING or TUNING
repeatedly to select a radio
station (frequency).
• When the receiver has received an FM
stereo broadcast, “ST” (stereo) indicator
lights up.
• You can also select a radio station using the
automatic tuning.
Automatic tuning:
Hold down TUNING or TUNING until the
frequency starts changing, and then release
the button.
When the receiver has received a broadcast,
the frequency automatically stops changing.
To quit the function while searching for a
broadcast, press TUNING or TUNING .
NOTE
• Pressing SEARCH – or SEARCH + on the receiver
also enables you to select the radio station.
• If an FM stereo broadcast is difficult to hear because
of noise, you may be able to hear the broadcast
more easily by pressing FM MODE to switch the
sound to monaural reception. In this case, “MONO”
lights up. To return the sound to stereo reception,
press FM MODE again.
NOTE
• If the spacing is switched, the preset radio station
memory will be erased.
Downloaded From DvDPlayer-Manual.com JVC Manuals
18
For the locations of the remote
control buttons, refer to page 18.
Listening to radio broadcasts (continued)
Tuning in to a preset
radio station
Presetting radio stations in the receiver allows you
to easily tune in to a radio station.
Presetting radio stations
You can store up to 30 FM radio stations and up to
15 AM radio stations.
1
2
Select a radio station you want
to store (A “Selecting a radio
station” on page 18).
Press MEMORY.
• The preset number flashes in the display
window on the receiver for about 5
seconds.
3
While the preset number is
flashing, press PRESET or
PRESET to select the preset
number you want to use.
• You can also select the preset number by
using the number buttons. (Refer to “Using
the number buttons”. (A page 15))
4
Press MEMORY or ENTER while
the selected number is flashing.
• “STORED” will appear and the selected
radio station will be stored.
NOTE
• When you store a radio station to a preset number
to which another radio station has previously been
stored, the newly set radio station replaces the
previously stored radio station.
19
Downloaded From DvDPlayer-Manual.com JVC Manuals
Tuning in to a preset radio station
1
2
3
Slide the remote control
mode selector to
RECEIVER.
Press FM/AM repeatedly to
select “FM” or “AM”.
Press the number buttons to
select the preset number of the
radio station to which you want
to tune in.
• Refer to “Using the number buttons”
(A page 15).
Basic operations of the DVD player
Remote control
mode selector
0OPEN/CLOSE
DISPLAY
Playing back a DVD/CD
F AUDIO
F DVD
DVD
FM/AM
AUX
3 (play)
GROUP/TITLE
/
PREVIOUS 4
NEXT ¢
SLOW
SLOW /¡
8
MENU/PL
5///2/3
(cursor)/
ENTER
ONE
TOUCH
REPLAY
Number
buttons
/1
7
TOP
MENU/PG
RETURN
1
2
Slide the remote control
mode selector to DVD.
Press 0 OPEN/CLOSE.
3
Place a disc.
• The disc tray ejects.
Letter-printed surface
Disc tray
• To listen to an 8 cm (3 3 16″) disc, place it on
the inner hollow of the disc tray.
4
Listening to radio/Playing back DVDs/CDs
Playing back DVDs/CDs
Press 3 (play) or DVD.
NOTE
SOURCE SELECT
Receiver
• You can also use SOURCE SELECT on the
receiver to select a loaded disc as the sound source.
• A menu screen may be displayed after starting
playback of a DVD. In this case, select a desired
item to playback by using the following buttons on
the remote control.
- Select a desired item using 5///2/3(cursor)
and press ENTER.
- You can also select a desired item using the
number buttons. Refer to “Using the number
buttons” (A page 15).
• When a DVD AUDIO is played back, signals are
converted into analog signals. Beginning playback
of a DVD AUDIO displays “DVD-ANALOG” for a
short time. When you take the disc out of the disc
tray, the display returns to “DVD-DIGITAL”
automatically.
• When using a DVD player other than the supplied
XV-EXA10, select “DVD-DIGITAL” playback or
“DVD-ANALOG” playback according to your usage.
Each time you hold down DVD, the playback
changes among “DVD-DIGITAL”, “DVD-ANALOG”
and “DVD-AUTO”. Return to the initial setting
(“DVD-AUTO”) when using the XV-EXA10.
• Depending on the disc, the actual operation may be
different from the description.
• When you select a source other than a DVD during
playback, the loaded disc stops automatically, and
“DVD OFF” is displayed in the display window on
the DVD player.
Downloaded From DvDPlayer-Manual.com JVC Manuals
20
Basic operations of the DVD player (continued)
Slide-show playback
This part explains the operation with displays of an
MP3 disc as examples.
For a JPEG disc, read “track” as “file”.
NOTE
• When files of different types are recorded on a disc,
select the file type to be played back. (A “FILE
TYPE ” on page 39)
1
2
Slide the remote control
mode selector to DVD.
Load a disc.
Numbers of the
Numbers of the current track
current group
(file) and total
and total groups tracks (files)
recorded on the included in the
loaded disc
current group
Elapsed
playback time of
the current track
(MP3/WMA/ASF
disc only)
Playback
status
• In step 6, for a JPEG disc, when 3 (play) is
pressed, files will be continuously played
back from the selected file (slide-show
playback), and when ENTER is pressed, only
a selected file will be played back.
• Display time for a file in slide-show playback
is about 3 seconds.
Display window on the DVD player
■DVD VIDEO/DVD AUDIO/DVD VR
When a disc is played back
Title/group/ Chapter/
original track
program/play number
list number
Elapsed playback time
• When a DVD AUDIO is played back, “GR” and
“TR” are displayed instead of “TITLE” and
“CHAP”.
• When a DVD VR is played back, “VR” is
displayed and “PG” (original program) or “PL”
(play list) is displayed instead of “TITLE”.
• If “BONUS” or “B.S.P.” is displayed during DVD
AUDIO playback, refer to pages 34 and 35.
When a disc is stopped
Current
group
3
4
5
6
Tag
Current
Number of the
information track (file) total tracks (files)
(MP3/WMA
recorded on the
disc only)
loaded disc
Press 5// (cursor) to select a
group.
Press 3 (cursor) to move to the
track list.
• Press 2 (cursor) to go back to the group
list.
Press 5// (cursor) to select a
track.
Press 3 (play) or ENTER.
NOTE
• You can also use GROUP/TITLE
or
in step 3
and PREVIOUS 4 or NEXT ¢ in step 5. In this
case, you can skip step 4.
• The number buttons can also be used in step 5. In
this case, you can skip steps 4 and 6. (Refer to
“Using the number buttons”. (A page 15))
21
Downloaded From DvDPlayer-Manual.com JVC Manuals
Disc type Total number of titles
• When a DVD AUDIO is loaded; “DVDA” is
displayed instead of “DVDV”, and the total
numbers of groups and the tracks are displayed
instead of the total numbers of the titles.
• When a DVD VR is loaded; “VR” is displayed
instead of “DVDV”, the total number of original
programs or the play lists is displayed instead of
the total number of titles, and “DVD VR” is
displayed instead of “DVD”.
■VCD/SVCD
■MP3/WMA/ASF/DivX/MPEG1/MPEG2 disc
When a disc is played back
Track number
• PBC (Play Back Control) is a signal recorded in
a VCD (version 2.0) for controlling playback. You
can enjoy interactive software or software with a
search function using a menu screen recorded in
a PBC compatible VCD. To play back a disc
without the PBC function, follow the instructions
below.
• Specify the track number using the number
buttons when the disc is stopped. Refer to
“Using the number buttons” (A page 15).
• Specify the track number using PREVIOUS
4 or NEXT ¢ when the disc is stopped,
and then press 3 (play).
• Press RETURN to go back to the upper layer
during PBC playback of a VCD or SVCD.
When a disc is stopped
Total playback time
Disc type Total
number of
tracks
• When the PBC function is activated, the display
below appears after the display above is
displayed for a short time.
When a disc is played back
Group Track
number number
Elapsed playback time
• When a WMA disc is played back, “WMA” is
displayed instead of “MP3”.
• When an ASF/DivX/MPEG1/MPEG2 disc is
played back, no disc type indicator is displayed.
When a disc is stopped
Disc type Group number
Playing back DVDs/CDs
For the locations of the remote
control buttons, refer to page 20.
Track
number
• When a WMA disc is loaded, “WMA” is displayed
instead of “MP3” in the upper indicator and the
lower display.
• When an ASF disc is loaded; “MP3” disappears
in the upper indicator, and “ASF” is displayed
instead of “MP3” in the lower display.
• When a DivX disc is loaded; “MP3” disappears
in the upper indicator, and “DivX” is displayed
instead of “MP3” in the lower display.
■JPEG disc
When a disc is played back or stopped
Group number File number
■CD
When a disc is played back
Track number
Elapsed playback time
When a disc is stopped
Disc type Total
Total playback time
number of
tracks
Downloaded From DvDPlayer-Manual.com JVC Manuals
22
Basic operations of the DVD player (continued)
Changing the display in
the display window
■ASF/DivX/MPEG1/MPEG2 disc
Normal display (as shown on page 22)
File type/group number/track number
Receiver
1
2
Slide the remote control
mode selector to
RECEIVER.
Press DISPLAY repeatedly.
• Each time you press DISPLAY, the display
toggles between the current source (DVD,
FM, AM, AUX-DIGITAL or AUX) and the
clock.
DVD player
1
2
Selecting a chapter/track
using the number buttons
(PBC off)
7 When a disc is played back
1
2
Slide the remote control
mode selector to DVD.
Press DISPLAY repeatedly
during playback.
• Each time you press DISPLAY, the display
changes.
7 DVD VIDEO
Normal display (as shown on page 21)
Slide the remote control
mode selector to DVD.
Use the number buttons to
select the chapter number or
track number.
• Refer to “Using the number buttons”
(A page 15).
NOTE
• You cannot use this function for some discs.
Stopping playback
Disc type/title number/chapter number
7 DVD AUDIO
Normal display (as shown on page 21)
7 When a disc is played back
Disc type/group number/track number
1
7 DVD VR
Normal display (as shown on page 21)
Disc type/original program (play list) number/
chapter number
7 MP3/WMA disc
Normal display (as shown on page 22)
File type/group number/track number
Text*
* When text, such as a file name, has been recorded in
the loaded MP3/WMA disc, the text appears and scrolls
in the display window on the DVD player.
23
Downloaded From DvDPlayer-Manual.com JVC Manuals
2
Slide the remote control
mode selector to DVD.
Press 7.
Pausing playback
Fast reverse/fast forward
search
7 When a disc is played back
1
2
Slide the remote control
mode selector to DVD.
7 When a disc is played back
1
Press 8.
• To return to normal playback, press 3
(play).
Advancing the picture
frame by frame
Slide the remote control
mode selector to DVD.
Playing back DVDs/CDs
For the locations of the remote
control buttons, refer to page 20.
There are two methods in step 2.
2
Press 1 or ¡.
• Each time you press the button, the speed
increases. To restore the normal speed,
press 3 (play).
Hold down PREVIOUS 4 or
NEXT¢.
• Fast reverse/fast forward search can be used
only while the button is pressed.
(only for moving image)
7 When a disc is paused
NOTE
1
• For some discs, sound is intermittent or no sound will
be produced during fast reverse/fast forward search.
• The selectable speeds and displays vary by the disc
type.
2
Slide the remote control
mode selector to DVD.
Press 8 repeatedly.
Messages displayed on the TV when the power is turned on
The following messages appear depending on the status of the DVD player.
NOW READING
REGION CODE
ERROR!
NO DISC
OPEN
CLOSE
CANNOT PLAY THIS
DISC
Appears when the DVD player is reading the disc information. Wait for a while.
Appears when the Region Code of the DVD does not match the code the DVD
player supports. (A page 47)
Appears when no disc is loaded.
Appears when the disc tray is opening.
Appears when the disc tray is closing.
Appears when an unplayable disc is attempted to be played back.
Downloaded From DvDPlayer-Manual.com JVC Manuals
24
Basic operations of the DVD player (continued)
Playing back from a
position 10 seconds before
(One touch replay)
Skipping to the
beginning of a chapter/
track/file
7 When a disc is played back
1
2
(PBC off)
Slide the remote control
mode selector to DVD.
Press
7 When a disc is played back
ONE TOUCH REPLAY.
NOTE
• This operation may not be used for some discs.
• You cannot go back to the previous title.
Slow motion playback
(only for moving image)
7 When a disc is paused
1
2
Slide the remote control
mode selector to DVD.
Press SLOW
or SLOW
.
• Each time you press the button, the speed
increases.
• Press 8 to pause playback, and press 3
(play) to return to normal playback.
NOTE
• No sound will be produced.
• The picture motion in the reverse direction may not
be smooth.
• For a VCD, SVCD or DVD VR, slow motion
playback can be used in the forward direction only.
1
2
Slide the remote control
mode selector to DVD.
Press PREVIOUS 4 or NEXT
¢.
• Each time you press the button, the
playback position skips to the beginning of
the previous or next chapter/track/file.
• Press PREVIOUS 4 once to skip back to
the beginning of the chapter or track
currently being played back (except for a
JPEG disc).
• Press GROUP/TITLE or
to select the
title or group.
• During playback of an MP3/WMA/JPEG/
ASF/DivX disc, press NEXT ¢ or /
(cursor) to play back the next file, or press
PREVIOUS 4 or 5 (cursor) to play back
the previous file.
NOTE
• You can use this function while the disc is stopped
except for a DVD VIDEO. You can use 5 or /
(cursor) to skip to the beginning of a track while you
are viewing the TV screen.
• You cannot use this function for some discs.
Guide icons displayed on the TV screen (on-screen guide)
25
Play
Containing multi-view angles
(A page 33)
Pause
Containing multi-audio languages
(A page 32)
Fast reverse/fast forward search
Containing multi-subtitle languages
(A page 32)
Slow motion playback (reverse/
forward directions)
The disc cannot accept the operation you
have attempted.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Skipping at about 5
minute intervals
You can skip within a file at about 5 minute
intervals.
This is useful especially when you want to skip
within a long file.
7 When a disc is played back
1
2
Resuming playback
When playback is stopped in the middle, playback
can be started from the stopped position.
Temporarily stopping playback
7 When a disc is played back
Slide the remote control
mode selector to DVD.
1
Press 2 or 3 (cursor).
2
• Each time you press the button, the
playback position skips to the beginning of
the previous or next interval. Each interval
is about 5 minutes.
Playing back DVDs/CDs
For the locations of the remote
control buttons, refer to page 20.
Slide the remote control
mode selector to DVD.
Follow any of the operations
below.
Press 7 once.*1 *2
NOTE
Press F AUDIO to turn off the power of the
receiver.
• Intervals are automatically assigned from the
beginning of a file.
• You can use this function only within the same file.
• You cannot use this function for some discs.
Press F DVD to turn off the power of the DVD
player.
Change the source to FM/AM or AUX.*2
*1 “RESUME” will be displayed. If 7 is pressed
again at this time, “RESUME” will disappear and
the stored information will be cleared.
*2 After playback is stopped, even if the receiver
or the DVD player is turned off by pressing
F AUDIO or F DVD, the position where
playback has been stopped will be stored.
Starting playback from the stored position
1
2
Slide the remote control
mode selector to DVD.
Press 3 (play).
NOTE
• This function does not work in program playback or
random playback.
• The position where playback starts again may be a
little different from the stopped position.
• When the menu screen is displayed, the resume
playback function may not work.
• The audio language, the subtitle language and the
angle at that time are stored together with the
stopped position.
• The stored position will be cleared if the disc tray is
opened.
• The resume playback function is activated as the
initial setting. You can disable the resume playback
function. (A “RESUME” on page 39)
Downloaded From DvDPlayer-Manual.com JVC Manuals
26
For the locations of the remote
control buttons, refer to page 20.
Basic operations of the DVD player (continued)
Selecting a track from
the menu screen
■Original program
No
1
2
3
4
5
6
(PBC off)
Date
12/03/04
12/09/04
12/18/04
12/20/04
12/25/04
12/28/04
Ch
L 1
L 1
L 1
L 1
L 1
L 1
Time
12:15
23:05
08:17
07:47
19:38
14:20
Title
La fleur
The last struggle
free flyer
BOOM!
Mr. Lawrence
Satisfy U
7 When a disc is stopped or played back
1
2
Slide the remote control
mode selector to DVD.
Starting time for the title
recording
Channel information
Press MENU/PL or TOP MENU/
PG.
• The menu screen will be displayed.
• Only TOP MENU/PG can be used for DVD
AUDIOs.
3
Title name
Recording date
■Play list
Press 5///2/3 (cursor) (only
for a DVD VIDEO or DVD AUDIO)
or the number buttons to select
the desired track.
No
1
2
3
4
• Refer to “Using the number buttons”
(A page 15).
• When the menu screen has a couple of
pages, press PREVIOUS 4 or NEXT
¢ to change the page (only for a VCD
and SVCD).
4
• You cannot use this function for a disc without a
menu screen.
• Playback may start for some discs without pressing
ENTER.
7 When a disc is stopped or played back
1
2
27
Slide the remote control
mode selector to DVD.
Press TOP MENU/PG to display
the original program or press
MENU/PL to display the play
list.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Chap
2
4
13
17
Length
0:23:24
1:04:39
0:41:26
0:09:08
Title
Nebula G.
CDJ
Secret Garden
S. Walker
Recording Total playback time for
date
the title
Number of chapters
included in the title
• The play list will not appear when a play list
has not been recorded to the disc.
Press ENTER.
NOTE
Date
12/03/04
12/15/04
12/24/04
12/27/04
3
4
Press 5// (cursor) to select the
desired title.
Press ENTER.
• When you have selected the original
program by pressing TOP MENU/PG in
step 2, playback will start from the selected
title to the following titles.
• When you have selected the play list by
pressing MENU/PL in step 2, only the
selected title will be played back.
Remote control
mode selector
F DVD
Playing back a DVD/CD
in the desired order
(Program playback)
GROUP/
TITLE
/
PREVIOUS
3 (play)
4
You can program a maximum of 99 tracks or
chapters. The same track or chapter can be
programmed more than once.
7 When a disc is stopped
ON
SCREEN
AUDIO
VFP
PAGE
ZOOM
PLAY
MODE
REPEAT
5///2/3
(cursor)/
ENTER
1
SUBTITLE
ANGLE
2
Number
buttons
3D PHONIC
Playing back DVDs/CDs
Convenient functions of the DVD player
Slide the remote control
mode selector to DVD.
Press PLAY MODE repeatedly
to display “PROGRAM” in the
display window on the DVD
player.
Example:
Display on the DVD player for a DVD VIDEO
CLOCK/
TIMER
CANCEL
Example:
TV screen for a DVD VIDEO (Program screen)
DVD player
Locking DVD/CD ejection
You can lock the disc tray to prevent the disc from
being ejected.
Setting
Turn off the DVD player. And while
holding down 7 on the DVD player,
press 0 on the DVD player.
• “LOCKED” appears in the display window on the
DVD player.
Releasing
Follow the same instructions as
those for setting.
• “UNLOCKED” appears in the display window on
the DVD player.
(Continued on the next page)
Downloaded From DvDPlayer-Manual.com JVC Manuals
28
Convenient functions of the DVD player (continued)
3
• Before selecting a bonus group of a DVD
AUDIO, cancel the “BONUS” display as
explained in “Playing back the bonus group”
on page 34.
• When you try to enter more than 99
chapters or tracks, “MEMORY FULL”
appears.
• In the case of a VCD, SVCD or CD, when
the total playback time reaches 9 hours 59
minutes 59 seconds, “--:--” will be displayed
in the display window on the DVD player.
Press the number buttons to
program chapters/tracks.
• Refer to “Using the number buttons”
(A page 15).
■Display on the DVD player for DVD VIDEO
• Select a title number, and then a chapter
number.
Title indicator
Chapter indicator
NOTE
• Only for a DVD VIDEO, DVD AUDIO, MP3, WMA
disc, if you press ENTER instead of specifying a
track/chapter number, “ALL” is displayed and all of
the tracks/chapters included in the selected group/
title are programmed.
Title number Chapter number Program number
■Display on the DVD player for DVD AUDIO/
MP3/WMA disc
4
• Select a group number, and then a track
number.
.
Group
indicator
Track indicator
Group
Chapter
number number
Program number
■Display on the DVD player for VCD/SVCD/CD
• Select a track number.
• As you finish the track selection, the total
time for the program playback will be
displayed.
.
Track indicator
Track number Program number
Example:
TV screen for a DVD VIDEO (Program screen)
29
Downloaded From DvDPlayer-Manual.com JVC Manuals
Press 3 (play).
• To return to normal playback, press PLAY
MODE repeatedly to turn off “PRGM” (the
upper indicator) in the display window on
the DVD player while the disc is stopped.
The program content will not be erased.
• The following operations erase the program
content.
• Hold down CANCEL until “ALL CLEAR!”
appears in the display window while the
program screen is displayed on the TV
screen (if CANCEL is pressed and
released quickly, programs will be erased
one by one).
• Open the disc tray.
• Turn off the power.
(Only when the setting save function
(A page 31) is not being used)
Playing back a DVD/CD
in a random order
(Random playback)
Playing back a DVD/CD
repeatedly (Repeat
playback)
7 When a disc is stopped
1
2
3
Slide the remote control
mode selector to DVD.
Press PLAY MODE repeatedly
to display “RANDOM” in the
display window on the DVD
player.
• “RANDOM” will also be displayed on the TV
screen.
Press 3 (play).
• The same chapter or track will not be
played back twice.
• To return to normal playback, press PLAY
MODE repeatedly to turn off “RND” (the
upper indicator) in the display window on
the DVD player while the disc is stopped.
• The following operations also cancel
random playback.
• Open the disc tray.
• Turn off the power.
(Only when the setting save function
(A page 31) is not being used)
• The previous track will not be returned to
even if PREVIOUS 4 is pressed
repeatedly during random playback.
(Playback will be returned to the beginning
of the current chapter or track.)
NOTE
• You cannot use the random playback function for
some DVD VIDEOs.
(PBC off)
7 When a disc is played back
1
2
Slide the remote control
mode selector to DVD.
Playing back DVDs/CDs
For the locations of the remote
control buttons, refer to page 28.
Press REPEAT.
• Each time you press the button, the repeat
mode changes.
Display on the
TV screen
Display in the display
window on the DVD
player
Usage for the repeat
mode
TITLE
ALL
REPEAT TITLE
Repeats the current
title.
ALL
or REPEAT ALL
ALL
REPEAT ALL
Repeats the whole
disc*1.
GROUP*2
or REPEAT
GROUP
GR
REPEAT GROUP*2
Repeats the current
group*3.
REPEAT CHAP*4
Repeats the current
chapter.
TRACK*4
or REPEAT
TRACK
REPEAT TRACK*4
Repeats the current
track.
OFF
or no display
REPEAT OFF
CHAP*4
Repeat off
*1 Repeats the whole program during program playback.
*2 For a DVD VR, “PG” is displayed during original
program playback, and “PL” is displayed during play
list playback.
*3 Repeats the current original program or the current
play list for a DVD VR.
*4 “STEP” is displayed during program/random playback.
NOTE
• The repeat playback can also be set on the menu
bar. (A “Playing back a specified part repeatedly
(A-B repeat playback)” on page 31)
• For a DVD VIDEO, DVD AUDIO and DVD VR, if the
source is switched to FM/AM or AUX, the repeat
mode will be cancelled.
• The repeat mode will be automatically cancelled if
there is a file that cannot be played back
(A page 47).
Downloaded From DvDPlayer-Manual.com JVC Manuals
30
Convenient functions of the DVD player (continued)
Playing back a specified
part repeatedly
(A-B repeat playback)
(PBC off)
Slide the remote control
mode selector to DVD.
You can save the settings for program playback,
random playback or repeat playback so that the
settings are activated even after the DVD player is
turned off and then on again.
Combining this function with the playback timer
(A page 43), you can make a variety of playback
settings.
Press ON SCREEN twice.
1
You can play back the desired part repeatedly by
specifying a start point (A) and an end point (B).
7 When a disc is played back
1
2
• The menu bar (A page 36) will be
displayed.
3
4
5
2
Press 2/3 (cursor) to select
OFF .
Press ENTER.
Press ENTER at the start point
of the part to be repeated
(specifying point A).
• The icon on the menu bar will be
A-
.
Press ENTER at the end point of
the part to be repeated
(specifying point B).
A-B .
• The icon on the menu bar will be
will appear in the display window on the
DVD player and the part between points A
and B will be played back repeatedly.
• A-B repeat playback can be cancelled by
following the operations below.
• Press 7.
A-B and press ENTER twice.
• Select
OFF .)
(Select
NOTE
• You can use A-B repeat playback only within the
same title or track.
• You cannot use A-B repeat playback during program
playback, random playback or repeat playback.
• You cannot use the A-B repeat playback function for
some DVD VIDEOs.
31
Press CLOCK/TIMER.
Press 5// (cursor) to display
.
7
Slide the remote control
mode selector to DVD.
• The current settings for program/random/
repeat playback will be stored.
Display on the DVD player
• Other repeat modes can be selected in this
step. For other repeat modes, refer to
“Playing back a DVD/CD repeatedly
(Repeat playback)” (A page 30).
6
Saving the playback
settings for next time
Downloaded From DvDPlayer-Manual.com JVC Manuals
NOTE
• To cancel the setting save function, press CLOCK/
TIMER again.
• Opening the disc tray also cancels the setting save
function.
• Resume playback does not work when the settings
for program/random/repeat playback are saved. For
example, if the program playback settings are saved
and F DVD is pressed to turn off the DVD player
during playback, pressing F DVD to turn on the
DVD player again and pressing 3 (play) starts
playback of the first programmed track/chapter.
Conversely, if the program playback settings are not
saved and 3 (play) is pressed after the DVD player
is turned on, the resume playback function operates
and playback starts from the point where the disc
was stopped.
• For a JPEG/ASF/DivX/MPEG1/MPEG2 disc, you
can use the setting save function for repeat
playback only.
Selecting the subtitles
(only for moving image)
This part explains the operation with displays of a
DVD VIDEO as examples.
You can use discs of other types in almost the
same manner.
7 When a disc contains subtitles and is played
back
1
2
1
2
Press ENTER.
• The subtitle language setting will change
automatically in a few seconds even if
ENTER is not pressed.
NOTE
• You can use this function with the menu bar
(A page 36).
• For a language code such as “AA”, refer to
“Language codes” (A page 51).
Downloaded From DvDPlayer-Manual.com JVC Manuals
Press AUDIO.
TV screen
• Each time you press the button, the audio
language will be changed. Also, the audio
language can be changed by pressing 5//
(cursor).
TV screen
Press 5// (cursor) to select a
subtitle language.
Slide the remote control
mode selector to DVD.
Example:
Press SUBTITLE.
• Each time you press the button, the subtitle
will toggle between on and off.
4
7 When a disc contains multiple audio
languages and is played back
Slide the remote control
mode selector to DVD.
Example:
3
Selecting the audio
language
Playing back DVDs/CDs
For the locations of the remote
control buttons, refer to page 28.
3
Press ENTER.
• The audio language setting will change
automatically in a few seconds even if
ENTER is not pressed.
NOTE
• You can use this function with the menu bar
(A page 36).
• For a language code such as “AA”, refer to
“Language codes” (A page 51).
• “ST”, “L” and “R” displayed when playing back a
VCD, SVCD or DVD VR respectively represent
“Stereo”, “Left sound” and “Right sound”.
• For a DivX disc, only the number of the language is
displayed on the TV screen.
32
Convenient functions of the DVD player (continued)
Selecting the view angle
Magnifying the picture
(ZOOM)
(only for moving image)
7 When a scene containing multi-view angles is
played back
1
2
Slide the remote control
mode selector to DVD.
(only for moving image)
7 When a disc is played back or paused
1
Press ANGLE.
Example:
TV screen
2
Slide the remote control
mode selector to DVD.
Press ZOOM.
• Each time you press the button, the picture
magnification will be changed.
• Each time you press the button, the angle
will be changed. Also, the angle can be
changed by pressing 5// (cursor).
3
Press ENTER.
• The angle setting will change automatically
in a few seconds even if ENTER is not
pressed.
NOTE
• You can use this function with the menu bar
(A page 36).
33
Downloaded From DvDPlayer-Manual.com JVC Manuals
3
Select the portion you want to
magnify by using 5///2/3
(cursor).
• To return to normal playback, select “ZOOM
OFF” in step 2.
NOTE
• For a JPEG disc, you cannot change the picture
magnification during slide-show playback.
• During ASF playback, there may be a case where
5///2/3 (cursor) does not work in step 3.
Adjusting the picture
quality (VFP)
7 When a disc is played back or paused
1
2
NOTE
• If no operation is made for several seconds during
the procedure, the settings made so far will be
automatically stored.
• “VFP” stands for “Video Fine Processor”.
Playing back the bonus
group
Slide the remote control
mode selector to DVD.
Press VFP.
There are some DVD AUDIOs with a special
group, called “bonus group”, recorded.
• The current setting will appear on the TV
screen.
NOTE
Playing back DVDs/CDs
For the locations of the remote
control buttons, refer to page 28.
• You can use this function when “BONUS” lights up
in the display window on the DVD player.
7 When a disc is played back
1
2
• The “GAMMA” setting adjusts the
brightness of neutral tints while maintaining
the brightness of dark and bright portions.
• The “SHARPNESS” setting adjusts the
screen sharpness.
3
Press 2/3 (cursor) to select
VFP mode.
• Selecting “NORMAL” is suitable for normal
usage, and selecting “CINEMA” is suitable
for a dark room. When selecting “NORMAL”
or “CINEMA”, proceed to step 8.
• Selecting “USER1” or “USER2” enables
you to make detailed adjustment in step 4
and the later steps.
4
5
Press5// (cursor) to select an
item to be adjusted.
Slide the remote control
mode selector to DVD.
Press GROUP/TITLE
repeatedly to select a bonus
group.
• “KEY_ _ _ _” appears on the TV screen,
and in the display window on the DVD
player.
3
Press the number buttons to
enter the pin code (4 digits).
• The method of obtaining a pin code differs
depending on the disc.
4
Press ENTER.
• When the correct pin code is entered,
“BONUS” disappears and the playback of
the bonus group starts.
• If an incorrect pin code is entered, try
entering the correct pin code again.
Press ENTER.
Example:
TV screen
GAMMA
6
7
Press 5// (cursor) to change
the value.
Press ENTER.
• To adjust other items, go back to step 4.
8
Press VFP.
Downloaded From DvDPlayer-Manual.com JVC Manuals
34
Convenient functions of the DVD player (continued)
Browsable still pictures
(B.S.P.)
Some DVD AUDIOs may have pictures called
B.S.P. (Browsable Still Pictures). The pictures can
be viewed as if you are turning pages.
NOTE
• You can use this function when “B.S.P.” lights up in
the display window on the DVD player.
2
Slide the remote control
mode selector to DVD.
Press PAGE.
• Each time you press the button, the still
picture will be changed. You can also switch
the picture using 5// (cursor).
Example:
3
TV screen
Press ENTER.
• The picture setting will change
automatically in a few seconds even if
ENTER is not pressed.
NOTE
• You can use this function with the menu bar
(A page 36).
35
The two speakers produce an effect resembling
surround-sound.
7 When a disc is played back
1
2
7 When a disc is played back
1
Creating realistic sound
(3D PHONIC)
Downloaded From DvDPlayer-Manual.com JVC Manuals
Slide the remote control
mode selector to DVD.
Press 3D PHONIC repeatedly to
select the desired sound effect.
Example:
Display on the DVD player
This indicator lights up when 3D PHONIC is
activated.
• “ACTION” is suitable for action movies,
sport programs or other lively programs.
• Select “DRAMA” to enjoy a sound effect
with a relaxing, natural atmosphere.
• Select “THEATER” to enjoy a sound effect
as if you were watching the movie in a
theater.
• Select “3D PHONIC OFF” to cancel 3D
PHONIC. (initial setting)
NOTE
• 3D PHONIC is effective for both the speakers and
headphones.
• If noise is produced or sound is distorted, select “3D
PHONIC OFF ”.
• When 3D PHONIC is activated, analog playback is
selected automatically, and “DVD-ANALOG” is
displayed in the display window on the receiver.
Canceling 3D PHONIC returns to “DVD-DIGITAL”
automatically. When a DVD AUDIO is played back,
signals are converted into analog signals regardless
of whether 3D PHONIC is activated or canceled.
• You cannot use this function for some DVD
AUDIOs.
• When 3D PHONIC is activated, the CC
CONVERTER function will be cancelled
automatically. (A page 17)
• For an ASF/DivX/MPEG1/MPEG2 disc, 3D
PHONIC does not work and creates no sound effect
even when “ACTION”, “DRAMA” or “THEATER” is
displayed.
Using the status bar and
the menu bar
7 When a disc is played back
1
2
Slide the remote control
mode selector to DVD.
Press ON SCREEN twice.
• “ON SCREEN” will appear in the display
window on the DVD player. The status bar
and the menu bar will appear on the TV
screen.
Example:
When a DVD VIDEO is loaded
Information displayed on the status bar
DVD VIDEO/DVD AUDIO/DVD VR (the example
below is for a DVD VIDEO)
Sound
Time Playback
signal type
status
(DVD VIDEO/DVD VR)
(DVD VIDEO)
Current chapter number
Current title number
(DVD AUDIO)
(DVD AUDIO)
Current group number Current track number
(DVD VR)
Current original
program number (PG)/
current play list
number (PL)
Playing back DVDs/CDs
For the locations of the remote
control buttons, refer to page 28.
VCD/SVCD/CD/ASF/DivX/MPEG1/MPEG2 disc
(the example below is for a CD)
0:25:58
Playback mode status
Time Playback
status
(VCD/SVCD/CD)
Current track number
(ASF/DivX/MPEG1/MPEG2 disc)
Repeat mode status
Status bar
NOTE
Menu bar
3
4
• The playback status has the same meaning of the
mark on the on-screen guide (A page 25).
Press 2/3 (cursor) to select an
item to be operated.
Press ENTER.
• The selected function can be set. For the
setting content, refer to “Function list”.
(A page 37)
• The currently active function is shown in
blue.
• To turn off the menu bar, press ON
SCREEN.
Downloaded From DvDPlayer-Manual.com JVC Manuals
36
For the locations of the remote
control buttons, refer to page 28.
Convenient functions of the DVD player (continued)
Function list
Designating the time (Time search)
For functions with no description of the operation,
press 5// (cursor) to select and press ENTER to
determine the function.
7 When a disc is played back
Changes the time information in the
display window on the DVD player and
the status bar. Each time ENTER is
pressed, the display will be changed.
DVD VIDEO/DVD AUDIO (operating
during playback)
TOTAL: Elapsed playback time of the
current title/group.
T.REM: Remaining time of the current
title/group.
TIME : Elapsed playback time of the
current chapter/track.
REM : Remaining time of the current
chapter/track.
DVD VR (operating during playback)
TOTAL: Elapsed playback time of the
current title/group.
T.REM: Remaining time of the current
title/group.
CD (operating during playback)/VCD/
SVCD
TIME : Elapsed playback time of the
current track.
REM : Remaining time of the current
track.
TOTAL: Elapsed playback time of the
disc.
T.REM: Remaining time of the disc.
A page 30
TIME
Time display
selection
1
2
3
4
5
TRACK
Chapter search
(DVD VIDEO/DVD
VR)/Track search
(DVD AUDIO)
Examples:
5:
5
24:
2
4
A page 32
Audio language/
Audio (DVD VIDEO/
DVD AUDIO/VCD/
SVCD)
A page 32
Subtitle language
(DVD VIDEO/DVD
VR/SVCD)
1/ 3
A page 33
View angle (DVD
VIDEO/DVD AUDIO)
PAGE -/Page switch (DVD
AUDIO)
37
Switches the browsable still pictures
(B.S.P.) recorded on a DVD AUDIO.
(A page 35)
Downloaded From DvDPlayer-Manual.com JVC Manuals
Press ENTER.
Input the time using the number
buttons (1-9, 0).
2
3
4
5
.
• You can skip the minute and second
setting.
• If the incorrect value is input, press 2
(cursor) to delete the values and input
values again.
A on the right
Selects a chapter/track. Press the
number buttons to input the chapter/
track number and press ENTER.
Press 2/3 (cursor) to select
.
Example:
When you want to play back a DVD VIDEO
from the position of (0 hour) 23 minutes 45
seconds, press the buttons in the order:
Time search
/
Press ON SCREEN twice.
• The menu bar will appear (A page 36).
Repeat mode
CHAP.
Slide the remote control
mode selector to DVD.
6
Press ENTER.
• To turn off the menu bar, press ON
SCREEN.
NOTE
• This function does not work for a DVD VIDEO with
no time information recorded.
• This function does not work during program
playback or random playback.
• For a CD, you can use this function any time.
• For a VCD or SVCD, you can use this function
during playback without the PBC function.
• Time search for a DVD VIDEO is from the beginning
of the title. Time search for a DVD AUDIO is from
the beginning of the track being played back. Time
search for a VCD, an SVCD and a CD is as follows:
• When the disc is stopped, time search is from the
beginning of the disc.
• When the disc is being played back, time search
is within the track currently being played back.
Basic operations
Remote control
mode selector
7 When a disc is stopped or no disc is loaded
(“NO DISC” is displayed)
1
2
Slide the remote control
mode selector to DVD.
Press SET UP.
• The following screen will be displayed on
the TV.
Playing back DVDs/CDs
Changing the initial settings with the preference screen
5///2/3
(cursor)/
ENTER
SET UP
Number
buttons
• Proceed with operations by following the
description on the TV screen.
LANGUAGE
NOTE
The initial settings of the DVD player can be
changed with the preference screen according to
the environment where the DVD player is used.
NOTE
• The top and bottom of the preference screen may
not be displayed on a wide TV. Adjust the picture
size on the TV.
Downloaded From DvDPlayer-Manual.com JVC Manuals
• If the selected language is not recorded on the disc,
the optimum language set for the disc will be
displayed.
• For a language code such as “AA”, refer to the
“Language codes” (A page 51).
Items
Contents
MENU
LANGUAGE
Selects the language for the DVD VIDEO
menu screen.
AUDIO
LANGUAGE
Selects the audio language for the DVD
VIDEO.
SUBTITLE
Selects the subtitle language for the DVD
VIDEO.
ON SCREEN
LANGUAGE
Selects the language displayed on the
preference screens.
38
Changing the initial settings with the preference screen (continued)
PICTURE
PICTURE
AUDIO
Items
Contents (
MONITOR
TYPE
16 : 9:
For an ordinary wide TV.
: initial setting)
Items
Contents (
DIGITAL
AUDIO
OUTPUT*
Select the output signal type suitable to the
equipment connected to the DIGITAL OUT
terminal (a decoder-built-in amplifier or
other digital equipment with an optical
input terminal). Refer to “List of
relationships of DIGITAL AUDIO OUTPUT
preference items and output signal”
(A page 40).
4 : 3 LB (Letterbox) :
For a TV with conventional 4:3 aspect ratio.
When a wide screen picture is input, the black
bars appear on the top and bottom of the
screen.
: initial setting)
PCM ONLY :
Equipment corresponding only to linear PCM.
DOLBY DIGITAL/PCM:
Dolby digital decoder or equipment having the
same function.
STREAM/PCM:
DTS/Dolby digital decoder or equipment
having the same function.
4 : 3 PS (Pan Scan):
For a TV with conventional 4:3 aspect ratio.
When a wide screen picture is input, the left
and right edges of the picture will not be
shown on the screen. (If the disc is not
compatible with Pan Scan, the picture will be
displayed at the Letterbox ratio.)
DOWN MIX
Select the signal suitable to the equipment
connected to the DIGITAL OUT terminal.
Set “DOWN MIX” only when “DIGITAL
AUDIO OUTPUT” is set to “PCM ONLY”.
DOLBY SURROUND:
Dolby Pro Logic decoder-built-in equipment.
STEREO :
Ordinary audio equipment.
PICTURE
SOURCE
Select an item suitable to the video source.
AUTO :
The video source type (a video or film) is
automatically selected.
FILM:
To view a film or video recorded with the
progressive scan method.
VIDEO:
To view a normal video.
SCREEN
SAVER
Select the Screen Saver mode between ON /
OFF (Screen Saver activates when there is no
operation made for about 5 minutes since a
still picture was last displayed).
FILE TYPE
Select an item suitable to the file type.
AUDIO :
For MP3/WMA files.
STILL PICTURE:
For JPEG files.
VIDEO:
For ASF/DivX/MPEG1/MPEG2 files.
D (Dynamic).
To correct the difference between high
RANGE
volume and low volume when playing back
COMPRESSION with low volume (only for a DVD recorded
with Dolby digital).
AUTO :
The D. RANGE COMPRESSION function
automatically works.
ON:
The D. RANGE COMPRESSION function
always works.
* When using the supplied XV-EXA10, make sure that
“DIGITAL AUDIO OUTPUT” is set to “PCM ONLY”.
OTHERS
Items
Contents (
RESUME
Select ON /OFF. (A page 26)
: initial setting)
ON SCREEN
GUIDE
Select ON /OFF. (A page 25)
AV
COMPULINK
MODE
When you want to control the supplied DVD
player and the connected TV or other
equipment at the same time, select a
setting according to the type of terminal on
the equipment connected to the DVD
player. (Refer to “Using the AV COMPU
LINK function” (A page 45).)
DVD1 :
When the video 3 input terminal on the TV or
the DVD input terminal is connected.
DVD2:
When the video 1 input terminal on the TV is
connected.
DVD3:
When the video 2 input terminal on the TV is
connected.
DivX
The DVD player has its own registration
REGISTRATION code. You can confirm the registration
code, when necessary. Once you have
played back a disc in which the registration
code is recorded, the registration code of
the DVD player is overwritten for copyright
protection.
39
Downloaded From DvDPlayer-Manual.com JVC Manuals
List of relationships of DIGITAL AUDIO OUTPUT preference items and output signal
Playback disc
DIGITAL AUDIO OUTPUT preference
PCM ONLY
DOLBY DIGITAL/PCM
48 kHz, 16/20/24 bit
Linear PCM DVD VIDEO
96 kHz linear PCM DVD VIDEO
48 kHz, 16 bit stereo linear PCM
48/96/192 kHz,
16/20/24 bit linear PCM DVD AUDIO*
48 kHz, 16 bit stereo linear PCM
44.1/88.2/176.4 kHz,
16/20/24 bit linear PCM DVD AUDIO*
44.1 kHz, 16 bit stereo linear PCM
DTS DVD VIDEO/DVD AUDIO*
DOLBY DIGITAL DVD VIDEO/DVD
AUDIO*
48 kHz, 16 bit stereo linear PCM
48 kHz, 16 bit stereo linear
PCM
VCD/SVCD/CD
DTS CD
MP3/WMA/DivX disc
STREAM/PCM
DTS bit stream
Playing back DVDs/CDs
For the locations of the remote
control buttons, refer to page 38.
DOLBY DIGITAL bit stream
44.1 kHz, 16 bit stereo linear PCM/48 kHz, 16 bit linear PCM
44.1 kHz, 16 bit linear PCM
DTS bit stream
32/44.1/48 kHz, 16 bit linear PCM
NOTE
* Copyright-protected DVD AUDIOs do not output signals.
• Among DVD VIDEOs without copyright protection, there may be some DVD VIDEOs that output a 20 or 24 bit
signal through the digital audio output terminals.
• To produce the sound from the loaded disc in the DVD player, select “PCM ONLY”. Otherwise the receiver does
not detect the signal and no sound is produced. (The initial setting is “PCM ONLY”.)
Downloaded From DvDPlayer-Manual.com JVC Manuals
40
Listening to the sound of other audio equipment
Listening to the sound of other audio equipment
Adjust the sound input level of the audio
equipment
Remote control
mode selector
You can adjust the sound input level of audio
equipment connected to the AUX terminals.
AUX
1
3 (play)
2
Slide the remote control
mode selector to
RECEIVER.
Press AUX to select “AUX”.
• Each time you press AUX, the display on
the receiver toggles between
“AUX-DIGITAL” and “AUX”.
• The source changes to the signal from the
AUX terminals.
3
Hold down MEMORY until the
input level is displayed.
• Each time you hold down the button, the
input level switches as follows:
MEMORY
LEVEL1 STORED: For normal use.
(initial setting)
Connect the other audio equipment to this system
in advance (A page 12).
LEVEL2 STORED: To correct distorted
sound caused by an
extremely high input
level from other
equipment.
1
2
Slide the remote control
mode selector to
RECEIVER.
Press AUX to select
“AUX-DIGITAL” or “AUX”.
• Each time you press AUX, the display on
the receiver toggles between
“AUX-DIGITAL” and “AUX”.
• The source changes to the signal from the
AUX terminals.
• You can also use SOURCE SELECT on the
receiver to select the signal from the AUX
terminals as the sound source.
3
Begin playback on the other
audio equipment.
• For details on beginning playback, refer to
the manual of the connected equipment.
4
Adjust the volume and the
sound quality of the system
(A page 16).
NOTE
• When no equipment is connected to the DIGITAL IN
AUX terminal or the power of the connected
equipment is off, after “AUX-DIGITAL” is selected,
the display changes to “AUX-D UNLOCK”.
41
Downloaded From DvDPlayer-Manual.com JVC Manuals
Timer
Remote control
mode selector
F AUDIO
Using the sleep timer
When the time you specify elapses, the system will
be turned off automatically.
1
2
2/3
(cursor)
Slide the remote control
mode selector to
RECEIVER.
Press SLEEP.
• Each time you press the button, the time
indicated in the display window on the
receiver changes (in minutes).
Example:
Display on the receiver when the sleep timer is set
to 60 minutes
Number
buttons
SET
CLOCK/
TIMER
SLEEP
CANCEL
The sleep timer will be automatically set in a few
seconds, and the indication will disappear.
NOTE
When the sleep timer is set, the display window
darkens automatically.
Listening to the sound of other audio equipment/Timer
Timer
Changing the time
Select the time again by pressing
SLEEP repeatedly in step 2.
Confirming the time
Press SLEEP once in step 2 while
the sleep timer is set.
Canceling the sleep timer
Press SLEEP repeatedly in step 2
until “SLEEP OFF” appears.
NOTE
• The sleep timer will also be cancelled when the
power is turned off.
Downloaded From DvDPlayer-Manual.com JVC Manuals
42
Timer (continued)
5
Set the clock beforehand. (A page 15)
Press 2 or 3 (cursor) to select
“ONCE” or “WEEKLY”, and
then press SET.
1
ONCE
WEEKLY
Using the playback timer
2
Slide the remote control
mode selector to
RECEIVER.
6
Press CLOCK/TIMER.
Display on the receiver
The playback timer works once.
The playback timer works
weekly or every day.
Press 2 or 3 (cursor) to select
the desired day of the week, and
then press SET.
• Each time you press 2 or 3 (cursor), the
display changes as follows.
When “ONCE” is selected
When “WEEKLY” is selected
(The playback timer works every day.)
• If you accidentally pressed CLOCK/TIMER
twice or more, press CLOCK/TIMER
repeatedly until the display shown above is
displayed.
3
4
Press SET.
7
Set the starting time and ending
time with 2, 3 (cursor), and
then press SET.
Example:
Display on the receiver when setting the
starting time to 8:45 (for U.S.A. or Canada
models)
Display on the receiver when setting the
ending time to 9:45 (for U.S.A. or Canada
models)
• Press 2 or 3 (cursor) to select the value
and press SET to set the value.
• You can use the number buttons instead of
2 or 3 (cursor). Refer to “Using the
number buttons” (A page 15).
• For U.S.A. or Canada models, the time
display on the receiver is a 12-hour clock.
• For models sold at post exchanges, the
time display on the receiver is a 24-hour
clock.
43
(The playback timer
works Monday to
Saturday.)
Downloaded From DvDPlayer-Manual.com JVC Manuals
8
(The playback timer
works Monday to
Friday.)
Press 2 or 3 (cursor) to select
the desired sound source, and
then press SET.
• If you have selected “FM” or “AM” in this
step, press 2, 3 (cursor) or the number
buttons to select the preset number of the
radio station whose broadcast you want to
listen to (Refer to “Using the number
buttons” (A page 15)), and then press SET.
Press 2 or 3 (cursor) to adjust
the playback volume, and then
press SET.
• You can use the number buttons to specify
the volume.
• The settings will appear in the display
window on the receiver.
9
Press F AUDIO to turn off the
receiver.
• The playback timer is available only when
the receiver is off.
This indicator lights up when the playback
timer is activated.
Activating the playback timer again
After following steps 1 and 2 on
page 43, press ENTER. Then press
F AUDIO to turn off the receiver.
Timer
For the locations of the remote
control buttons, refer to page 42.
NOTE
NOTE
• Complete the playback timer setting at least 1
minute prior to the starting time you have selected in
step 4.
• While setting the playback timer, you can return to
the previous step by pressing CANCEL or you can
stop the setting by pressing CLOCK/TIMER.
• When the playback starts, the volume gradually
increases to the selected level.
• You can make a variety of playback settings by
combining the playback timer and saving the
settings for program playback, random playback or
repeat playback. (A page 31)
Canceling the playback timer
• When the power cord of the receiver is
disconnected from the AC outlet or the power is
interrupted, the clock and the playback timer
settings may be lost. If the settings are lost, set the
clock and playback timer again.
Confirming the playback timer settings
Press SET repeatedly after
following steps 1, 2 and 3 on
page 43.
• To return to the normal display while confirming
the settings, press CLOCK/TIMER.
Changing the playback timer settings
Set the playback timer again from
step 1 on page 43.
Press CANCEL after following
steps 1 and 2 on page 43.
NOTE
• Even after you canceled the playback timer, the
setting remains stored.
Downloaded From DvDPlayer-Manual.com JVC Manuals
44
Using the AV COMPU LINK function
When a JVC-manufactured TV with AV COMPU
LINK II or III terminals is connected to the DVD
player using these terminals, operating either the
TV or the DVD player controls the other equipment
at the same time.
Connection and setup
Operation
1
2
NOTE
• “AV COMPU LINK” is printed for terminals on some
JVC-manufactured TVs. These terminals are no
different from the “AV COMPU LINK I/II” or “AV
COMPU LINK” terminal.
• Refer to “OTHERS” (A page 39) for determining
the “AV COMPULINK MODE” setting.
• Also refer to the manual of the TV to be connected
to the DVD player.
AV
COMPU LINK
II or III
JVC-manufactured TV
DVD player (rear panel)
Connection cord
(not supplied)
MODE”
Input terminal on the TV “AV COMPULINK
setting
Video 1
DVD2
Video 2
DVD1
• Connect the video 3 (DVD) input terminal on the
TV.
• If the video 3 input terminal is used for the
playback of a digital video movie, this terminal
does not work with the AV COMPU LINK
function.
45
Downloaded From DvDPlayer-Manual.com JVC Manuals
3
Turn on the main power of the
TV.
Slide the remote control
mode selector to DVD.
Press 0 OPEN/CLOSE.
• The disc tray ejects.
4
5
Place a disc.
Press 3 (play) or DVD.
• The power of the TV is turned on.
• The input mode on the TV changes to either
the video 1 input or the video 3 (DVD) input.
Special cautions
Care of the cabinet
When cleaning the system, use a soft cloth and follow the
relevant instructions on the use of chemically-coated
cloths. Do not use benzene, thinner or other organic
solvents including disinfectants. These may cause
deformation or discoloring.
Notes on handling
7 Important cautions
Installation of the system
• Select a place which is level, dry and neither too hot
nor too cold; between 5°C and 35°C (between 41°F
and 95°F).
• Leave sufficient distance between the system and the
TV.
• Do not use the system in a place subject to vibration.
Power cord
• Do not handle the power cord with wet hands!
• A small amount of power is always consumed while
the power cord is connected to the wall outlet.
• When unplugging the power cord from the wall outlet,
always pull on the plug, not the power cord.
To prevent malfunctions of the system
• There are no user-serviceable parts inside. If anything
goes wrong, unplug the power cord and consult your
dealer.
• Do not insert any metallic object into the system.
• Do not use any non-standard shape disc (like a heart,
flower or credit card, etc.) available on the market,
because it may damage the system.
• Do not use a disc with tape, stickers, or paste on it,
because it may damage the system.
Care of the disc tray
When cleaning the disc tray, gently wipe the dirt off the
surface with a soft cloth dampened with a small amount
of a neutral detergent diluted with water, preventing the
discoloration and damage to its surface.
Reference
Reference
If water gets inside the system
Turn the system off and disconnect the power cord plug
from the wall outlet, then call the store where you made
your purchase. Using the system in this condition may
cause fire or electrical shock.
7 When condensation or water drops adhere to the lens
In any of the following cases, condensation or water
drops may adhere to the lens, preventing the system
from working properly:
• Immediately after room heating starts
• When the system is installed in a steamy or damp
space
• When the system is suddenly moved from a cold place
to a warm space
In any of these cases, leave the system turned on for 1 or
2 hours before use.
Label sticker
Sticker
Paste
Note about copyright laws
Check the copyright laws in your country before
recording from DVDs, VCDs, SVCDs and CDs.
Recording of copyrighted material may infringe copyright
laws.
Note about copy guard system
DVDs are protected by copy guard system. When you
connect the system to your VCR directly, the copy guard
system activates and the picture may not be played back
correctly.
7 Safety precautions
Avoid moisture, water and dust
Do not place the system in moist or dusty places.
Avoid high temperatures
Do not expose the system to direct sunlight and do not
place it near a heat source.
When you are away
When away on travel or for other reasons for an extended
period of time, disconnect the power cord plug from the
wall outlet.
• Manufactured under license from Dolby Laboratories. “Dolby”, “MLP Lossless”, and the double-D symbol are
trademarks of Dolby Laboratories.
• “DTS” and “DTS 2.0+DIGITAL OUT” are registered trademarks of Digital Theater Systems, Inc.
• This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents
and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this
copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
• “Official DivX CertifiedTM product”, “Plays DivX® 5, DivX® 4, DivX® 3, and DivX® VOD video content (in compliance
with DivX CertifiedTM technical requirements)”, “DivX, DivX Certified”, and associated logos are trademarks of
DivXNetworks, Inc. and are used under license.
Downloaded From DvDPlayer-Manual.com JVC Manuals
46
About DVDs/CDs
Region code of DVD VIDEO
Playable DVD/CD types
Audio CD format
VCD/SVCD
format
MP3/WMA/
JPEG format
DVD Video
format
DVD VR format
DivX format
ASF (Advanced
Systems
Format)
MPEG1/MPEG2
format
CD-R/
CD-RW
Playable
DVD-R1
DVD-RW
—
—
Playable
—
—
Playable
Playable4 Playable4
—
Playable
Playable
—
Playable
Playable2
Playable3
Playable
Playable
Playable
Playable
Playable
Playable
Playable
Playable
Examples:
If a DVD VIDEO with an improper Region Code
number is loaded, “REGION CODE ERROR!” appears
on the TV screen and playback cannot start.
• On some DVD VIDEOs, DVD AUDIOs, VCDs, SVCDs
or DivX discs, their actual operation may be
different from what is explained in this manual.
This is due to the disc programming and disc
structure, not a malfunction of this system.
Discs you can play back:
Disc Type
• Discs should be finalized before being played back.
1 A DVD-R recorded in multi-border format is also
playable (except for dual layer discs).
2 Only when a DVD-R is compatible with CPRM
(Content Protection for Recordable Media), DVD VR
format can be used.
3 A DivX formatted DVD-ROM is also playable.
4 Among MP3/WMA/JPEG discs, only discs formatted
with a combination of Universal Disc Format and ISO
9660 (known as UDF Bridge) are playable.
Some discs may not be played back because of their disc
characteristics, recording conditions, or damage or stains
on them.
It is possible to play back finalized +R/+RW (DVD Video
Format only) discs. “DVD” lights on the front display
panel when a +R/+RW disc is loaded.
Only sounds can be played back from the following discs:
MIX-MODE CD
CD-G
CD-EXTRA
CD TEXT
47
DVD VIDEO players and DVD VIDEO discs have their
own Region Code numbers. This system can play back
DVD VIDEO discs whose Region Code numbers include
the system’s Region Code, which is indicated on the rear
panel.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Mark (Logo)
DVD VIDEO
DVD AUDIO
AU D I O
VCD
SVCD
CD
CD-R
CD-RW
DivX
Notes on DivX discs and files
• The following discs cannot be played back:
DVD-ROM (except for MP3/WMA/JPEG/ASF/DivX/
MPEG1/MPEG2 format), DVD-RAM, CD-ROM, CD-I
(CD-I Ready), Photo CD, SACD, etc.
Playing back these discs will generate noise and
damage the speakers.
Damaged discs and discs in an extraordinary shape
(other than a disc of 12 cm or 8 cm (4 3 4 ″ or 33 16″) in
diameter) cannot be played back.
• The system supports DivX 5.x, 4.x and 3.11.
• The system supports DivX files with a resolution of
720 x 480 pixels or less (30 fps) and 720 x 576 pixels
or less (25 fps).
• Audio stream should conform to MPEG1 Audio Layer-2
or MPEG Audio Layer-3 (MP3).
• The system does not support GMC (Global Motion
Compression).
• Files encoded in the interlaced scanning mode may
not be played back correctly.
• Playing back a DivX disc may take a long time. The
elapsed time is not displayed until playback starts. The
elapsed time may also not be displayed correctly.
About MP3/WMA/JPEG/ASF/DivX/MPEG1/
MPEG2 discs
Playable MP3/WMA/JPEG/ASF/DivX/MPEG1/MPEG2
discs and files
• CDs recorded in the ISO 9660 format are playable
(except CDs recorded in the “packet write” format
(UDF format)).
• CDs recorded with multiple sessions are also playable.
• Files with an extension of “.mp3”, “.wma”, “.jpg”,
“.jpeg”, “.asf”, “.divx”, “.div”, “.avi”, “.mpg” or “.mpeg”
(extensions with uppercase and lowercase letters
mixed are also acceptable) are playable.
Notes on MP3/WMA/JPEG/ASF discs and files
• A disc may not be played back, or reading it may take a
long time depending on its recording conditions or
properties.
• The time needed for reading varies with the number of
groups or tracks (files) recorded on the disc.
• If a character other than single byte English characters
is used in the file name of an MP3/WMA/JPEG/ASF
file, the track/file name will not be displayed correctly.
• The order of tracks/groups displayed on the MP3/WMA
control screen, and the order of files/groups displayed
on the JPEG control screen may be different from that
of files/folders displayed on a computer monitor
screen.
• A commercially available MP3/WMA disc may be
played back in an order different from that indicated on
the label attached to the disc.
• Playing back an MP3/WMA/JPEG/ASF disc may take
a long time. The elapsed time is not displayed until
playback starts. The elapsed time may also not be
displayed correctly.
• For an MP3/WMA file, a disc with a sampling
frequency of 44.1 kHz and transmission rate of 128
kbps is recommended.
• This system can play back a baseline JPEG file,
excluding monochromatic JPEG files.
• This system can play back JPEG data taken with a
digital camera conforming to the DCF (Design Rule for
Camera File System) standard (when a function such
as the automatic image rotation function of a digital
camera is applied, the data no longer complies with
the DCF standard, so the image may not be
displayed).
• If data has been processed, edited and restored with
computer image editing software, the data may not be
displayed.
• This system cannot play back animations such as
MOTION JPEG, still images (TIFF etc.) other than
JPEG, or image data with sound.
• The resolution of 640 x 480 pixels is recommended for
JPEG files. If a file has been recorded at a resolution
of more than 640 x 480 pixels, display may take a long
time. An image with a resolution of more than 8 192 x
7 680 pixels cannot be displayed.
• The system supports ASF files recorded with the
maximum bit rate of 384 kbps and an audio coder
decoder of G.726.
• The maximum size of the playback picture is 352 x 288
pixels (CIF).
Downloaded From DvDPlayer-Manual.com JVC Manuals
Reference
Discs that cannot be played back
Notes on MPEG1/MPEG2 discs and files
• The stream structure of MPEG1/MPEG2 discs and
files should conform to MPEG system/program stream.
• 720 x 576 pixels (25 fps)/720 x 480 pixels (30 fps) is
recommended for the highest resolution.
• This system also supports the resolutions of 352 x
576/480 x 576/352 x 288 pixels (25 fps) and 352 x 480/
480 x 480/352 x 240 pixels (30 fps).
• The profile and level should be MP@ML (Main Profile
at Main Level)/SP@ML (Simple Profile at Main Level)/
MP@LL (Main Profile at Low Level).
• Audio streams should conform to MPEG1 Audio Layer2 or MPEG2 Audio Layer-2.
Caution for DualDisc playback:
The Non-DVD side of a “DualDisc” does not comply with
the “Compact Disc Digital Audio” standard. Therefore,
the use of Non-DVD side of a DualDisc on this product
may not be recommended.
48
About DVDs/CDs (continued)
Disc structure
DVD VIDEO/DVD VR
A DVD VIDEO consists of “titles” and each title
may be divided into “chapters”.
A DVD VR consists of “original programs” or “play
lists” and each original program/play list may be
divided into “chapters”.
.
Title 1/Original program 1/
Play list 1
Title 2/Original
program 2/Play list 2
Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2
DVD AUDIO
A DVD AUDIO consists of “groups” and each group
may be divided into “tracks”.
Some discs include a “bonus group” that requires a
password for playback (A page 34).
Group 1
Track 1
Track 2
Group 2
Track 3
Track 1
Track 2
VCD/SVCD/CD
VCD, SVCD and CD consist of “tracks”.
In general, each track has its own track number.
(On some discs, each track may also be further
divided by indexes.)
Track 1
Track 2
Track 3
Track 4
Track 5
MP3/WMA/JPEG/ASF/DivX/MPEG1/MPEG2
discs
On an MP3/WMA/JPEG/ASF/DivX/MPEG1/
MPEG2 disc, each still picture (material) is
recorded as a track/file. Tracks/files are usually
grouped into a folder. Folders can also include
other folders, creating hierarchical folder layers.
This system simplifies the hierarchical construction
of a disc and manages folders by “groups”.
Group 1
Track 1/
File 1
Track 2/
File 2
Group 2
Group 3
Group 4
Group 5
This system can recognize up to 4 000 tracks/files
in a disc. Also, the system can recognize up to 150
tracks/files per group and up to 99 groups in a disc.
Since the system ignores tracks/files with numbers
exceeding 150 and groups with numbers
exceeding 99, these cannot be played back.
• If there is any type of files other than MP3/WMA/
JPEG/ASF/DivX/MPEG1/MPEG2 files in a
folder, those files are also counted in the total file
number.
49
Downloaded From DvDPlayer-Manual.com JVC Manuals
When you encounter a problem that seems to be a
fault, check the following points before contacting
the JVC service center:
Power source
7 Power does not come on.
• The power cord of the receiver or the DVD
player is not connected to an AC outlet.
→ Connect the power cord correctly.
(A page 13)
Operation
7 You cannot operate any button.
• Some specific operations may be restricted
for some discs.
7 The remote control does not work.
• The batteries have run out.
→ Replace the batteries. (A page 5)
• The remote control mode selector is slid to
wrong position.
→ Most of the buttons on the remote control
are assigned to specific remote control
modes. Slide the remote control selector to
the proper position referring to the
explanation of each function.
7 A disc cannot be played back.
• In the case of DVD VIDEOs
→ Check the Region Code number of the
disc. (A page 47)
• “PLAYABLE Err” is displayed in the display
window.
The disc cannot be played back on this DVD
player.
→ Check the disc type. (A pages 47 and 48)
7 MP3, WMA, JPEG, ASF, DivX, MPEG1 or
MPEG2 files cannot be played back.
• The loaded disc may include files of different
types (MP3, WMA, JPEG, ASF, DivX,
MPEG1 or MPEG2). You can play back only
the files of the types selected with “FILE
TYPE”. (A page 39)
7 The picture is distorted.
• A video cassette recorder is connected
between the DVD player and the TV.
→ Connect the DVD player directly to the TV.
(A page 13)
Reference
Troubleshooting
7 The screen size is abnormal.
• The screen size is not set correctly.
→ Set “MONITOR TYPE” according to the TV
you are using. (A page 39)
7 The TV screen darkens.
• “SCREEN SAVER” is set to “ON”.
→ Press any button. (A page 39)
Sound
7 There is no sound.
• Speakers are not connected correctly.
→ A page 9
• The receiver and the DVD player are not
connected correctly.
→ A page 10
• The sound is muted.
→ A page 16
• “NO AUDIO” is displayed in the display
window.
The disc may have been produced through
illegal copying.
→ Check the disc at the store where you
bought the disc.
7 The sound is distorted.
• The volume is turned up too high.
→ Turn down the volume. (A page 16)
7 No sound comes out of the subwoofer.
• “S. WOOFER OFF” is selected.
→ Press S.WFR OUT repeatedly until
“S. WOOFER ON” appears. (A page 11)
Radio
7 The sound has a lot of static./You cannot
receive a radio broadcast.
• The antenna is not connected correctly.
→ Connect the antenna correctly.
(A pages 7 and 8)
Images
7 No picture appears.
• The composite video cord is not connected
correctly.
→ A page 12
• An S-video cord and a component video cord
are connected at the same time.
→ Connect either cord. (A page 13)
(Continued on the next page)
Downloaded From DvDPlayer-Manual.com JVC Manuals
50
Troubleshooting (continued)
Other
7 You cannot switch audio or subtitles between
languages.
• The disc does not contain multiple
languages.
→ If only a single language is recorded on the
disc, you cannot switch the current
language to another language.
(A page 32)
7 No subtitle is displayed.
• The disc does not contain any subtitles.
→ A DVD VIDEO without subtitles cannot
display any subtitles.
• The subtitle language is set to “OFF”.
→ Specify a language. (A page 38)
• Before or after point A or B in A-B repeat
playback, no subtitle may be displayed.
7 The disc cannot be ejected.
• DVD/CD ejection is locked.
→ A page 28
7 “LR ONLY” is displayed in the display window
(for a DVD AUDIO).
• This is not a malfunction. When a down mix
prohibited track is played back for multichannel sound, the left and right sounds are
output directly as they are.
7 The tweeters produce no sound.
• “Single Amp” is selected on the receiver.
→ Select “Bi-Amp”. (A page 11)
If the system does not work properly
despite correction measures
aforementioned
Many functions of this system are controlled by
microprocessors that can be reset by recycling the
power supply. If pressing any button does not
result in the normal action, disconnect the power
cord from the outlet, wait for a while, and connect
the power cord again.
51
Downloaded From DvDPlayer-Manual.com JVC Manuals
Language codes
Code
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GL
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
IW
JI
JW
KA
KK
KL
KM
KN
KO
KS
KU
KY
LA
LN
LO
LT
LV
MG
MI
Language
Afar
Abkhazian
Afrikaans
Ameharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean (KOR)
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Code
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NL
NO
OC
OM
OR
PA
PL
PS
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Language
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay (MAY)
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Wolof
Xhosa
Yoruba
Zulu
Receiver (RX-EXA10)
DVD player (XV-EXA10)
Tuner
U.S.A. and Canada models
FM frequency:
87.5 MHz - 108.0 MHz
AM frequency:
530 kHz - 1 710 kHz
Post exchange models
FM frequency:
87.50 MHz - 108.00 MHz
AM frequency:
531 kHz - 1 710 kHz
(9 kHz spacing)
530 kHz - 1 710 kHz
(10 kHz spacing)
Amplifier
Output power (Tweeter): 20 W + 20 W
at 6 C (10 kHz, THD 10 %)
Output power (Woofer): 30 W + 30 W
at 6 C (1 kHz, THD 10 %)
Playable DVDs/CDs
DVD VIDEO/DVD AUDIO
VCD/SVCD/CD
CD-R/RW (VCD/SVCD/CD/MP3/WMA/JPEG/DivX/
ASF/MPEG1/MPEG2 format)
DVD-R (MP3/WMA/JPEG/DVD VIDEO/DVD VR
[CPRM]/DivX/ASF/MPEG1/MPEG2 format)
DVD-RW (MP3/WMA/JPEG/DVD VIDEO/DVD VR
[CPRM]/DivX/ASF/MPEG1/MPEG2 format)
Terminal
• Synchronization terminal x 1 (for connecting XV-EXA10)
• Optical digital input terminal x 1 (for connecting XV-EXA10)
-21 dBm to -15 dBm
• Audio input terminals (2) x 1 (for connecting XV-EXA10)
500 mV/50 k C
• Audio output speaker terminals (2) x 4
Impedance: 6 C
• FM antenna terminal x 1
• AM antenna terminal x 1
• Audio output subwoofer terminal x 1
500 mVrms/10 k C
• Optical digital input terminal x 1 (for connecting other
equipment)
-21 dBm to -15 dBm
• Audio input terminals (2) x 1 (for connecting other
equipment)
Level 1: 500 mV/50 k C
Level 2: 250 mV/50 k C
• Audio output headphone terminal x 1
11 mW/32 C (Impedance :16 C to 1 k C)
General
U.S.A. and Canada models
Power source:
AC 120 V
, 60 Hz
Power consumption: 30 W (in operation)
0.8 W (on standby)
Post exchange models
Power source:
AC 110 - 240 V
, 50 Hz/60 Hz
Power consumption: 30 W (in operation)
0.9 W (on standby)
Dimensions (W x H x D): 245 mm x 80 mm x 297 mm
(911 16 ″ x 3 3 16 ″ x 11 3 4 ″)
Weight (1 unit):
2.7 kg (6.0 lbs)
Reference
Specifications
Terminal
• Synchronization terminal x 1 (for connecting RXEXA10)
• Optical digital output terminal x 1 (for connecting RXEXA10)
-21 dBm to -15 dBm
• Audio output terminals (2) x 1 (for connecting RXEXA10)
• Composite video output terminal x 1
1.0 Vp-p, sync negative, 75 C terminated
• S-video output terminal x 1
Y: 1.0 Vp-p, sync negative, 75 C terminated
C: 0.286 Vp-p, sync negative, 75 C terminated
• Component video output terminals (3)
Y: 1.0 Vp-p, sync negative, 75 C terminated
PB: 0.7 Vp-p, 75 C terminated
PR: 0.7 Vp-p, 75 C terminated
• AV COMPU LINK terminal x 1
General
U.S.A. and Canada models
Power source:
AC 120 V
, 60 Hz
Power consumption: 9 W (in operation)
0.5 W (on standby)
Post exchange models
Power source:
AC 110 - 240 V
, 50 Hz/60 Hz
Power consumption: 9 W (in operation)
0.9 W (on standby)
Dimensions (W x H x D): 245 mm x 80 mm x 270 mm
(91116 ″ x 3 3 16 ″ x 101116 ″)
Weight (1 unit):
2.2 kg (4.9 lbs)
Designs and specifications are subject to change
without notice.
Speakers (SP-EXA10)
Type:
2-way bass-reflex type
Magnetically shielded type
Tweeter:
2 cm (13 16 ″) wood dome
Woofer:
10.5 cm (4 3 16 ″) wood cone
Power handling capacity: 20 W
(Tweeter)
Power handling capacity: 30 W
(Woofer)
Impedance:
6C
Sound pressure level: 82 dB/W • m
Dimensions (W x H x D): 143 mm x 257 mm x 243 mm
(51116 ″ x 10 1 8 ″ x 9 5 8 ″)
Weight (1 unit):
3.5 kg (7.8 lbs)
Downloaded From DvDPlayer-Manual.com JVC Manuals
52
For U.S.A.
53
Downloaded From DvDPlayer-Manual.com JVC Manuals
For U.S.A.
Downloaded From DvDPlayer-Manual.com JVC Manuals
54
EX-A10
COMPACT
T COMPONENT SYSTEM
EN
c 2005 Victor Company of Japan, Limited
Downloaded From DvDPlayer-Manual.com JVC Manuals
1005SKMMODJEM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising