d avmb2
ACCESSORIES
Models D-AVMB2 and DS-AVMB2
Audio and Video Monitor BNC Panels
•
•
•
•
•
•
•
•
Stereo Audio Input to Stereo Audio Output
Stereo Input on Mini-Jack
Unbalanced Audio Output on Detachable Terminal Block
Video Monitor Input on Standard Video Connector
Rear-Panel Video Outputs (R,G,B,H,V) on BNC Jacks
BNC Jacks are Isolated from Chassis Ground
Available in RDL White/Gray (D-AVMB2)
Available in Stainless Steel (DS-AVMB2)
DS-AVMB2
D-AVMB2
The D-AVMB2 and DS-AVMB2 are Decora®-compatible audio input accessories from Radio Design Labs. All metal enclosures are attractively
finished in white or brushed stainless steel to complement the decor encountered in commercial environments. Custom labeling is available at
www.rdlnet.com.
The D/S-AVMB2 is the ideal choice in installations requiring a wall-mounted audio and video monitor input or output
plate for computers, monitors and projectors. The panel is typically installed as an audio/video input plate, but may
equally be used as an output jack panel.
The front panel features a standard HD-15 video monitor connector. Video components, video sync and their
respective ground returns are separated to feed five BNC jacks on the rear panel. The BNC jacks are isolated from
the module chassis ground so the appropriate signal grounds pass through without adding a video ground loop at the
panel.
The front panel features a single 3.5 mm stereo mini-jack, intended for stereo consumer line-level audio sources.
The left and right signal inputs are fed to a rear-panel detachable terminal block. The audio signals are unbalanced
and are intended for short wiring runs where balanced lines are not required.
The D/S-AVMB2 is the ideal choice for providing convenient end-user computer inputs to feed monitors or projectors
in small facilities such as boardrooms or classrooms. Use it individually or in conjunction with other RDL products as
part of a complete audio/video system.
RDL • 659 N. 6th St. • Prescott, AZ., USA 86301 • (928) 443-9391 • FAX (928) 443-9392 • www.rdlnet.com
Installation/Operation
ACCESSORIES
EN55103-1 E1-E5; EN55103-2 E1-E4
Typical Performance reflects product at publication time
exclusive of EMC data, if any, supplied with product.
Specifications are subject to change without notice.
Models D-AVMB2 and DS-AVMB2
Audio and Video Monitor BNC Panels
USER INPUT CONNECTIONS
Consumer Audio
Source on RCA
Jacks
Video Source From
Computer
VIDEO
OR
Consumer Audio
Source on Mini- Jack
AUDIO
INSTALLER CONNECTIONS
G
B
B
G
R
V
V
Video Signal to
Monitor or Projector
R
H
L
R
H
D/DS-AVMB2
UNBALANCED
AUDIO OUT
Left
Note: BNC video jacks are insolated from the
chassis ground to prevent video ground loops.
The BNC connectors used to connect the
monitor or projector should not be allowed to
contact the metal mounting box, if used.
Right
Unbalanced Connections to
Amplifier, Monitor or Other
Equipment Input
TYPICAL PERFORMANCE
Audio input connector:
Video input connector:
Audio output connector:
Video output connectors (5):
Dimensions:
Mounting Box Minimum Dimensions:
891-5375
Mini-jack 3.5 mm (Stereo)
Female HD-15
Detachable terminal block (Left and Right unbalanced audio)
BNC (R: Red; G: Green; B: Blue; H: Horizontal Sync; V: Vertical Sync)
Height:
4.13 in.
10.49 cm
Width:
1.7 in.
4.32 cm
Depth:
1.4 in.
3.56 cm
Width:
1.80 in.
4.57 cm
Depth:
0.15 in. (0.38 cm) plus the depth of the installer-provided BNC connectors
Radio Design Labs Technical Support Centers
U.S.A. (800) 933-1780, (928) 778-3554; Fax: (928) 778-3506
Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising