Advantech | PPC-L128T | User manual | Advantech PPC-L128T User manual

User Manual
PPC-L128T
Intel® AtomTM N270 Processorbased Fanless Panel PC with
12.1" TFT-LCD
Copyright
The documentation and the software included with this product are copyrighted
2009by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the
right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech
Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any
infringements of the rights of third parties, which may result from its use.
Acknowledgements
Award is a trademark of Award Software International, Inc. Intel and Celeron are
trademarks of Intel Corporation.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft Corp. RTL is a trademark of
Realtek Semiconductor Co., Ltd.
All other product names or trademarks are properties of their respective owners.
For more information on this and other Advantech products, please visit our websites
at:
http://www.advantech.com
http://www.advantech.com/ppc
For technical support and service, please visit our support website at:
http://support.advantech.com
This manual is for the PPC-L128T.
PPC-L128T User Manual
Part No. 200K128T10
Edition 1
Printed in China
November 2009
ii
Declaration of Conformity
FCC Class B
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning! Any changes or modifications made to the equipment which are not
expressly approved by the relevant standards authority could void your
authority to operate the equipment.
iii
PPC-L128T User Manual
Packing List
Before you begin installing your card, please make sure that the following materials
have been shipped:
PPC-L128T series panel PC
User manual
Accessories for PPC-L128T
– Y-shaped adapter for PS/2 mouse and keyboard
– Warranty card
– DC plug-in housing (female) is connected on the AC/DC power adapter
– Driver DVD-RW disc
– Mounting kits and packet of screws
If any of these items are missing or damaged, contact your distributor or sales representative immediately.
Additional Information and Assistance
1.
2.
Visit the Advantech web site at www.advantech.com where you can find the latest information about the product.
Contact your distributor, sales representative, or Advantech's cus- tomer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
Product name and serial number
Description of your peripheral attachments
Description of your software (operating system, version, application software, etc.)
A complete description of the problem
The exact wording of any error messages
Caution! Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equiv- alent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
Warning! 1.
2.
3.
4.
5.
PPC-L128T User Manual
Input voltage rated 12 ~ 24 V, 5 A ~ 3.75 A
Use a 3 V @ 195 mA lithium battery
Packing: please carry the unit with both hands, handle with care
Maintenance: to properly maintain and clean the surfaces, use only
approved products or clean with a dry applicator
CompactFlash: Turn off power before insert- ing or removing CompactFlash storage card.
Contact information:
Our European representative: Advantech Europe GmbH Kolberger
Strafle 7
D-40599 Dsseldorf, Germany
Tel: 49-211-97477350
Fax: 49-211-97477300
iv
Safety Instructions
1.
2.
3.
Read these safety instructions carefully.
Keep this User Manual for later reference.
Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.
v
PPC-L128T User Manual
PPC-L128T User Manual
vi
Contents
Chapter
1
General Information ............................1
1.1
1.2
Introduction ............................................................................................... 2
General Specifications .............................................................................. 2
1.2.1 General ......................................................................................... 2
1.2.2 Standard PC functions .................................................................. 2
1.2.3 VGA/LCD Interface ....................................................................... 3
1.2.4 Audio function ............................................................................... 3
1.2.5 PCIe bus Ethernet interface.......................................................... 3
1.2.6 Touchscreen (Optional) ................................................................ 3
1.2.7 Optional modules .......................................................................... 4
1.2.8 Environment.................................................................................. 4
LCD Specifications.................................................................................... 4
Dimensions ............................................................................................... 5
Figure 1.1 Dimensions of PPC-L128T ......................................... 5
1.3
1.4
Chapter
2
System Setup .......................................7
2.1
A Quick Tour of the Panel PC ................................................................... 8
Figure 2.1 Front view of PPC-L128T panel PC ........................... 8
Figure 2.2 Rear view of Panel PC ............................................... 8
Figure 2.3 Side view of the panel PC .......................................... 9
Figure 2.4 Bottom view of the panel PC ...................................... 9
Installation Procedures.............................................................................. 9
2.2.1 Connecting the power cord ........................................................... 9
2.2.2 Connecting the keyboard or mouse .............................................. 9
2.2.3 Switching on the power............................................................... 10
Figure 2.5 Connect the power cord to the DC inlet.................... 10
Running the BIOS Setup Program .......................................................... 10
Installing System Software...................................................................... 11
2.4.1 Method 1: Use the Ethernet ........................................................ 11
2.4.2 Method 2: Use the COM ............................................................. 11
2.4.3 Method 3: Use a DVD-RW.......................................................... 11
Installing the Drivers................................................................................ 11
2.2
2.3
2.4
2.5
Chapter
3
Hardware Installation and Upgrading ..
13
3.1
3.2
Introduction ............................................................................................. 14
Installing the 2.5" Hard Disk Drive (HDD) ............................................... 14
Figure 3.1 Installing primary 2.5" HDD ...................................... 14
Installing the battery pack ....................................................................... 15
Figure 3.2 Installing the battery pack......................................... 15
3.3
Chapter
4
Jumper Settings and Connectors ....17
4.1
Jumpers and Connectors ........................................................................ 18
4.1.1 Setting jumpers ........................................................................... 18
4.1.2 Jumpers and connectors............................................................. 19
Table 4.1: Jumpers and Connector functions............................ 19
4.1.3 Locating jumpers and connectors ............................................... 20
Figure 4.1 Jumpers and Connectors on the PPC-L128T mothervii
PPC-L128T User Manual
4.2
4.3
board ........................................................................ 20
CMOS Clear for External RTC (CN13(2-3))............................................ 20
Table 4.2: CMOS clear (CN13) ................................................. 20
4.2.1 COM1/COM2/COM3 pin 9 output setting (CN20&CN21) ........... 21
Table 4.3: COM1/ COM2 pin 9 output setting (CN20).............. 21
Table 4.4: COM3 pin 9 output setting (CN21) .......................... 21
VGA Interface ......................................................................................... 21
4.3.1 LCD panel power setting ............................................................ 21
Appendix A
I/O Pin Assignments ......................... 23
A.1
Keyboard and PS/2 Mouse Connector (CN27)....................................... 24
Table A.1: Keyboard and mouse connector (CN27).................. 24
USB port (CN19)..................................................................................... 24
Table A.2: USB port (CN19) ...................................................... 24
COM1 RS-232 serial port (CN37) ........................................................... 24
Table A.3: COM1 RS-232 serial port (CN37) ............................ 24
COM2 (CN28) ......................................................................................... 25
Table A.4: COM2 (CN28) ......................................................... 25
COM3 RS-232 serial port (CN38) ........................................................... 25
Table A.5: COM3 RS-232 serial port (CN38) ............................ 25
GPIO port (CN29) ................................................................................... 26
Table A.6: GPIO port (CN29)..................................................... 26
VGA Connector (CN39) .......................................................................... 26
Table A.7: VGA connector (CN39) ............................................ 26
PCI Bus connector (CN18) ..................................................................... 27
Figure A.1 PCI connector........................................................... 27
Table A.8: PCI pin assignments ................................................ 28
PCI Express Bus connector (CN16) ....................................................... 29
Table A.9: PCIExpress pin assignments ................................... 29
How to setup Teaming function on PPC-L128/L157............................... 30
A.10.1 Team together ............................................................................ 30
A.10.2 Dismiss! ...................................................................................... 35
A.10.3 TESTING .................................................................................... 37
A.2
A.3
A.4
A.5
A.6
A.7
A.8
A.9
A.10
PPC-L128T User Manual
viii
Chapter
1
1
General Information
This chapter gives background
information on the PPC-L128T
panel PC.
Sections include:
Introduction
General Specifications
LCD Specifications
Dimensions
1.1 Introduction
The PPC-L128T panel PC is an Intel low-power Intel® AtomTM N270 processor computer that is designed to serve as a human machine interface (HMI) and as a multimedia computer. It is a PC-based system with 12.1" color TFT LCD display, on-board
PCIe Ethernet controller, multi-COM port interfaces and an audio controller. With a
built in internal IDE connector (for CF card), One SATA connector for HDD and one
for ODD,and an PCI/PCIe expansion socket, the PPC-L128T is as compact and user
friendly as a multifunction computer. In addition, its “fit anywhere” design makes it
very flexible and able to be used in many different kinds of installations. It can be wall
mounted, panel mounted or stood upright on a desktop.
For system integrators, this simple, complete, compact and highly integrated multimedia system lets you easily build a panel PC into your applications. Common industrial applications include factory automation systems, precision machinery, and
production process control. It is also suitable for many nonindustrial applications,
including interactive kiosk systems, entertainment management, and car park automation. Our panel PC is a reliable, cost-effective solution to your application's processing requirements.
1.2 General Specifications
1.2.1 General
Dimensions (W x H x D): 340.5 x 269.3 x 70.5 mm
Weight: 3.63 kg
– Power supply: ATX type
– Input Voltage: +12 ~ 24 VDC, 5 A ~ 3.75 A
– Power adaptor: AC/DC (Optional PS-DC19-L157E ) Input voltage: 100 ~ 240
VAC
– Output voltage: 19 V @ 4.74 A
Disk drive housing: Space for one 2.5" SATA HDD, one slim type DVD-RW
Front panel: IP65/NEMA4 compliant
1.2.2 Standard PC functions
CPU: On board Intel® AtomTM N270, 1.6 GHz with 512 L2 cache
BIOS: Award 8 Mbit flash BIOS, ACPI 2.0 Compliant
System Chipset: Intel® 945GSE + Intel ICH7M
Front side bus: 533 MHz
2nd level cache: 512 KB
System Memory: One 200-pin SO-DIMM socket, accepting up to 2 GB DDR2
400/ 533
PCI bus interface: PCI 33MHz/32Bit Supports one connectors.
Keyboard/mouse connector: Supports PS/2 Keyboard and Mouse
GPIO port: One GPIO port supports controller and surveillance function.
Serial ports: Three serial ports with two RS-232 ports (COM 1 and 3), one RS232/422/485 port (COM2). All ports are compatible with 16C550 UARTs, +5 V
(0.5 A) / +12 V (0.5 A) power supply selectable
Universal serial bus (USB) port: Support Up to 6 USB V2.0 ( 4 x external, 2 x
internal.
PCIe bus expansion slot: Accepts one PCIe card
PPC-L128T User Manual
2
Chipset: Integrated in Intel 945GSE
Frame buffer: Supports 128MB frame buffer with system memory
Interface: VGA/ LCD interface, support for 18-bit TFT
Display mode: CRT Modes: 2048 x 1536 @ 32bpp (60Hz);
LCD/Simultaneous Modes: 1024 x768 @ 16bpp (60 Hz)
1.2.4 Audio function
Chipset: Intel ICH7M South Bridge
Audio controller: ALC888 HD Audio Ver 2.0 compliant interface, Multi- stream
Direct sound and Direct Sound 3D acceleration
Stereo sound: 24-bit full-duplex codec
Audio interface: Microphone in, Line in, Line out, Speaker L, Speaker R
1.2.5 PCIe bus Ethernet interface
Chipset: Marvell 88E8053-A3-NNC1C000 PCIe local bus Ethernet controller
Ethernet interface: Full compliance with IEEE 802.3, 1000Base-T 100Base-T
and 10 Base-T specifications.Support 802.1p, 802.1q. Includes software drivers
and boot ROM
1000/100/10Base-T auto-sensing capability
Wake-on-LAN: Supports Wake-on-LAN function with ATX power control
Teaming Function: Support Teaming Function(refer to A.10)
1.2.6 Touchscreen (Optional)
Type
Analog Resistive
Resolution
Continuous
Light Transmission
80%
Controller
USB interface
Power Consumption
<5 V @ 60 mA
Software Driver
Supports Windows 2000/XP
Durability
(touches in a lifetime)
35 million
3
PPC-L128T User Manual
General Information
1.2.3 VGA/LCD Interface
Chapter 1
Mini PCIe bus expansion slot: Accepts one mini PCIe bus card(Wire less LAN
card)
Solid State Disk: Supports one 50-pin socket for CompactFlash type I/II (True
IDE mode)
Watchdog timer: 255-level timer intervals, from 15 sec to 14835 sec, setup by
software, jumperless selection, generates system reset
Battery: 3.0 V @ 195 mA lithium battery
Power management: Supports power saving modes including S0:Normal/
S1:Standby/S3:Suspend modes. APM 1.2 compliant
1.2.7 Optional modules
Memory: One 200-pin SO-DIMM socket, accepting up to 2 GB DDR2 400/533
DVD-RW Module: Slim type DVD-RW Module 989KL128T00E
Combo Module: Slim type Combo Module 989KL128T01E
Wireless LAN module: 989KL128T02E (Build in IEEE 802.11b/g AzureWave
AW-NE768 Mi MINI PCIe card)
Adaptor: PS-DC19-L157E
HDD: 2.5" SATA HDD
Operating System: Windows XP,Vista
Touchscreen: Analog resistive(PPC-L128T-R80-XE)
Battery pack: Rechargable Li-ion 3S2P 11.1 V 4400 mAh(1760000837)
1.2.8 Environment
Operating Temperature: 0 ~ 45° C (32 ~ 113° F)
Operating Temperature with battery: 0 ~ 35° C (32 ~ 95° F)
Storage Temperature: -20 ~ 60° C
Relative humidity: 10 ~ 95% @ 40° C (non-condensing)
Shock: 10 G peak acceleration (11 ms duration)
Certification: EMC: CE, FCC, BSMI, VCCI. Safety: UL 60950, CB, CCC, BSMI
Vibration: 5 ~ 500 Hz 1 G RMS Random vibration
1.3 LCD Specifications
Display type: 12.1" TFT LCD
Max. resolution: 1024 x 768
Colors: 262 K
Dot size (mm): 0.24 x 0.24
Viewing angle: 80° (left), 80° (right), 80° (up), 80° (down)
Luminance: 450 cd/m2
Temperature: -30 ~ 70° C
*VR control: Brightness could be modified through BIOS
Backlight lifetime: 50,000 hours
* The VR control is defined by hot key in DOS or BIOS mode as below: Ctrl-AltF3, Ctrl-Alt-F4.
Note!
The color LCD display installed in the panel PC is high-quality and reliable. However, it may contain a few defective pixels which do not
always illuminate. With current technology, it is impossible to completely
eliminate defective pixels. Advantech is actively working to improve this
technology.
PPC-L128T User Manual
4
Chapter 1
1.4 Dimensions
General Information
Unit: mm [inch]
Figure 1.1 Dimensions of PPC-L128T
5
PPC-L128T User Manual
PPC-L128T User Manual
6
Chapter
2
2
System Setup
This chapter details system setup
on the PPC-L128T panel PC.
Sections include:
A Quick Tour of the Panel PC
Installation procedures
Running the BIOS Setup Program
Installing System Software
Installing the Drivers
2.1 A Quick Tour of the Panel PC
Before you start to set up the panel PC, take a moment to become familiar with the
locations and purposes of the controls, drives, connectors and ports, which are illustrated in the figures below.
When you place the panel PC upright on the desktop, its front panel appears as
shown in Figure 2.1.
Figure 2.1 Front view of PPC-L128T panel PC
When you turn the panel PC around and look at its rear cover, you will find the I/O
section as shown in Fig. 2.2. (The I/O section includes vari- ous I/O ports, including
serial ports, the Ethernet port, USB ports, the Line-in/Line-out jack, and so on.) The
battery door cover is at the bottom of the panel PC, as shown in Fig. 2.4.
PCI/PCIe expansion
slot cover
PS2 mouse
and keyboard
GPIO port
DC inlet
Ethernet jack
USB 2.0 x 3
Main power switch
Line-in jack
Line-out jack
Mic-in jack
Serial ports
USB 2.0
Ethernet jack
VGA port
Figure 2.2 Rear view of Panel PC
PPC-L128T User Manual
8
CompactFlash socket
CFC eject button
Chapter 2
Compact DVD-RW drive
DVD-RW activity light
DVD-RW eject button
Figure 2.3 Side view of the panel PC
Door Cover
Battery
Figure 2.4 Bottom view of the panel PC
2.2 Installation Procedures
2.2.1 Connecting the power cord
The panel PC can be powered by a DC electrical outlet or the battery. Be sure to
always handle the power cords by holding the plug ends only. Please follow the Figure 2-5 to connect the male plug of the power cord to the DC inlet of the panel PC.
2.2.2 Connecting the keyboard or mouse
Before you start the computer, please connect the Y-shaped adaptor to the PS/2
mouse and keyboard port on the I/O section of the panel PC, then connect the necessary mouse or keyboard to the Y-shaped adapter or
serial ports.
9
PPC-L128T User Manual
System Setup
Speaker
2.2.3 Switching on the power
When you look at the rear side of the panel PC, you will see the power switch as
shown in Figure 2.2.
Power cord
AC/DC Power adapter
DC inlet
Figure 2.5 Connect the power cord to the DC inlet
2.3 Running the BIOS Setup Program
Your panel PC is likely to have been properly set up and configured by your dealer
prior to delivery. You may still find it necessary to use the panel PC's BIOS (Basic
Input-Output System) setup program to change system configuration information,
such as the current date and time or
your type of hard drive. The setup program is stored in read-only memory (ROM). It
can be accessed either when you turn on or reset the panel PC, by pressing the ‘Del’
key on your keyboard immediately after powering on the computer.
The settings you specify with the setup program are recorded in a special area of
memory called CMOS RAM. This memory is backed up by a battery so that it will not
be erased when you turn off or reset the system. Whenever you turn on the power,
the system reads the settings stored in CMOS RAM and compares them to the
equipment check conducted during the power on self-test (POST). If an error occurs,
an error message will be displayed on screen, and you will be prompted to run the
setup program.
If you want to change the setup of BIOS, refer to Chapter 9 for more detailed information.
PPC-L128T User Manual
10
Recent releases of operating systems from major vendors include setup programs
which load automatically and guide you through hard disk preparation and operating
system installation. The guidelines below will help you determine the steps necessary
to install your operating system on the panel PC hard drive.
Note!
Some distributors and system integrators may have already preinstalled system software prior to shipment of your panel PC.
2.4.1 Method 1: Use the Ethernet
You can use the Ethernet port to download software to the HDD.
2.4.2 Method 2: Use the COM
You can use Lap Link 6 or similar transmission software. Connect
another PC to the PPC-L128T with an appropriate cable and transmit the software to
the PPC-L128T.
2.4.3 Method 3: Use a DVD-RW
If required, insert your operating system's installation or setup diskette into the diskette drive until the release button pops out.
The BIOS of the panel PC supports system boot-up directly from the DVD-RW drive.
You may also insert your system installation DVD-RW into the DVD-RW drive.
Power on your panel PC or reset the system by pressing the ‘Ctrl+Alt+Del’ keys
simultaneously. The panel PC will automatically load the operating system from the
diskette or DVD-RW.
If you are presented with the opening screen of a setup or installation pro- gram, follow the instructions on screen. The setup program will guide you through preparation
of your hard drive, and installation of the operaing system. If you are presented with
an operating system command prompt, such as A:\>, then you must partition and format your hard drive, and manually copy the operating system files to it. Refer to your
operat- ing system user manual for instructions on partitioning and formatting a hard
drive.
2.5 Installing the Drivers
After installing your system software, you will be able to set up the Ether- net, SVGA,
audio, and touchscreen functions. All drivers are stored in a DVD-RW disc entitled
“Drivers and Utilities” which can be found in your accessory box.
The various drivers and utilities in the DVD-RW disc have their own text files which
help users install the drivers and understand their functions. These files are a very
useful supplement to the information in this manual.
Note!
The drivers and utilities used for the PPC-L128T panel PCs are subject
to change without notice. If in doubt, check Advantech's website or contact our application engineers for the latest informa- tion regarding drivers and utilities.
11
PPC-L128T User Manual
System Setup
Installing software requires an installed HDD. Software can be loaded in the PPCL128T using any of four methods:
Chapter 2
2.4 Installing System Software
PPC-L128T User Manual
12
Chapter
3
3
Hardware Installation
and Upgrading
This chapter details installing the
PPC- L128T panel PC hardware.
Sections include:
Overview of Hardware Installation and Upgrading
Installing the 2.5" Hard Disk
Drive (HDD)
Installing the battery pack
3.1 Introduction
The panel PC consists of a PC-based computer that is housed in a plastic rear panel
and a metal shielding case. You can install a HDD, DRAM, and battery pack by
removing the rear panel and shielding case. Any maintenance or hardware upgrades
can be easily completed after remov- ing the rear panel and shielding case.
If you are a systems integrator and need to know how to completely dis- assemble
the panel PC, you can find more useful information in Appendix C.
Warning! Do not remove the plastic rear cover until you have verified that no
power is flowing within the panel PC. Power must be switched off and
the power cord must be unplugged. Every time you service the panel
PC, you should be aware of this.
3.2 Installing the 2.5" Hard Disk Drive (HDD)
You can attach one Serial Advanced Technology Attachment (SATA) hard disk drive
to the panel PC's internal controller. The SATA controller supports faster data transfer
and allows the SATA hard drive to exceed 150 MB. The following are instructions for
installation:
1. Detach and remove the plastic rear cover.
2. There is a metal brace which holds the HDD to the upper left-hand side of the
metal shielding case. (See Fig. 3.1.)
3. Place the HDD in the metal brace, and tighten the screws.
4. The HDD cable (SATA 7P+1*5P-2.5/SATA(15+7)P) is next to the metal brace.
Connect the HDD cable to the PC board (CN5&CN6). Plug the other end of the
cable into the SATA hard drive.
5. Put the plastic rear cover on and tighten the screws.
Plastic rear cover
Figure 3.1 Installing primary 2.5" HDD
PPC-L128T User Manual
14
1.
2.
3.
Pull up the battery door cover on the right bottom of PPC-L128T.
Put the battery pack in, and then connect the battery cable to battery connector
in the PPC-L128T. Make sure the red wire corresponds to Pin 1 on the connector.
Close the battery door cover.
Red color (pin1)
Battery pack
Battery cable
Figure 3.2 Installing the battery pack
15
PPC-L128T User Manual
Hardware Installation and Upgrading
Battery door cover
Chapter 3
3.3 Installing the battery pack
PPC-L128T User Manual
16
Chapter
4
4
Jumper Settings and
Connectors
This chapter tells how to set up
the panel PC hardware, including
instructions on setting jumpers
and connecting peripherals,
switches and indicators. Be sure
to read all the safety precautions
before you begin the installation
procedures.
Sections include:
Jumpers and Connectors
CMOS Clear for External RTC
(J5)
COM Port Interface
VGA Interface
Watchdog Timer Configuration
4.1 Jumpers and Connectors
4.1.1 Setting jumpers
You can configure your panel PC to match the needs of your application by setting
jumpers. A jumper is the simplest kind of electrical switch. It consists of two metal
pins and a small metal clip (often protected by a plastic cover) that slides over the
pins to connect them. To “close” a jumper, you connect the pins with the clip. To
“open” a jumper you remove the clip. Sometimes a jumper will have three pins,
labeled 1, 2 and 3. In this case, you would connect either pins 1 and 2 or pins 2 and
3.
open
closed
closed 2-3
The jumper settings are schematically depicted in this manual as follows:.
1
open
closed
2
3
closed 2-3
A pair of needle-nose pliers may be helpful when working with jumpers.
If you have any doubts about the best hardware configuration for your application,
contact your local distributor or sales representative before you make any changes.
PPC-L128T User Manual
18
The motherboard of the PPC-L128T has a number of jumpers and connectors that
allow you to configure your system to suit your applications. The table below lists the
function of each of the board’s jumpers.
Table 4.1: Jumpers and Connector functions
LVDS connector
CN3
Inverter power connector
CN4
CF Slot ,TYPEII
CN5
SATA HDD signal connector (2.5" HDD)
CN6
SATA HDD power connector (2.5" HDD)
CN7
DDR2 SO-DIMM
CN8
MINI PCIe slot
CN9
5 Wires T/S connector
CN11
SATA ODD signal connector
CN12
SATA ODD power connector
CN16
PCIe (x1) slot
CN18
PCI bus expansion slot
CN19
Internal USB connector
CN23
Internal Speaker connector
CN33
Internal power connector
CN40
LCD light sensor connector
CN41
Front panel connector
PCN1
Battery connector
CN13
Clear CMOS connector
CN14
AT/ATX selection connector
CN20
COM1/2 Pin9 function selection
CN21
COM3 Pin9 function selection
19
Jumper Settings and Connectors
CN1
Chapter 4
4.1.2 Jumpers and connectors
PPC-L128T User Manual
4.1.3 Locating jumpers and connectors
Figure 4.1 Jumpers and Connectors on the PPC-L128T motherboard
4.2 CMOS Clear for External RTC (CN13(2-3))
Warning! To avoid damaging the computer, always turn off the power supply
before setting "Clear CMOS". Set the jumper back to "Normal operation"
before turning on the power supply.
This jumper is used to erase CMOS data and reset system BIOS informa- tion.
The procedure for clearing CMOS is:
1. Turn off system.
2. Short pin 2 and pin 3.
3. Return jumper to pins 1 and 2.
4. Turn on the system. The BIOS is now reset to its default setting.
Table 4.2: CMOS clear (CN13)
* Normal operation
Clear CMOS
* Default normal operation setting
PPC-L128T User Manual
20
Chapter 4
4.2.1 COM1/COM2/COM3 pin 9 output setting (CN20&CN21)
Table 4.3: COM1/ COM2 pin 9 output setting (CN20)
CN20
Default Ring function
3
5
7
9
2
4
6
8
10
1
3
5
7
9
2
4
6
8
10
Jumper Settings and Connectors
1
* +5V output
* +12V output
Note!
1
3
5
7
9
2
4
6
8
10
Pins 1, 3, 5, 7 and 9 are dedicated to COM1.
Pins 2, 4, 6, 8 and 10 are dedicated to COM2.
Table 4.4: COM3 pin 9 output setting (CN21)
CN21
Default Ring function
Ring function (1-2)
1
5
Output 5 V(3-4)
1
5
Output 12 V(4-5)
1
5
4.3 VGA Interface
4.3.1 LCD panel power setting
The panel PC's AGP SVGA interface supports 12V LCD displays. The LCD cable
already has a built-in default setting. You do not need to adjust any jumper or switch
to select the panel power.
21
PPC-L128T User Manual
PPC-L128T User Manual
22
Appendix
A
A
I/O Pin Assignments
A.1 Keyboard and PS/2 Mouse Connector (CN27)
Table A.1: Keyboard and mouse connector (CN27)
Pin
Signal
1
KB_DATA
2
MS-DATA
3
GND
4
+5 V
5
KB_CLK
6
MS-CLK
A.2 USB port (CN19)
Table A.2: USB port (CN19)
Pin
Signal
1
+V5_USB
3
DATA-
5
DATA+
7
GND
9
GND
2
+V5_USB
4
DATA-
6
DATA+
8
GND
10
GND
A.3 COM1 RS-232 serial port (CN37)
Table A.3: COM1 RS-232 serial port (CN37)
Pin
Signal
Pin
Signal
1
DCD#
2
RX
3
TX
4
DTR#
5
GND
6
DSR#
7
RTS#
8
CTS#
9
RI#
PPC-L128T User Manual
24
Table A.4: COM2 (CN28)
Pin
Signal RS-232
RS-422
RS-485
1
DCD
TX-
DATA-
2
RX
TX+
DATA+
3
TX
RX+
4
DTR
RX-
5
GND
GND
6
DSR
7
RTS
8
CTS
9
RI
A.5 COM3 RS-232 serial port (CN38)
Table A.5: COM3 RS-232 serial port (CN38)
Pin
Signal
Pin
Signal
1
DCD#
2
RX
3
TX
4
DTR#
5
GND
6
DSR#
7
RTS#
8
CTS#
9
RI#
25
PPC-L128T User Manual
Appendix A I/O Pin Assignments
A.4 COM2 (CN28)
A.6 GPIO port (CN29)
Table A.6: GPIO port (CN29)
1
GPIO0
2
GPIO1
3
GPIO2
4
GPIO3
5
GND
6
GPIO4
7
GPIO5
8
GPIO6
9
GPIO7
A.7 VGA Connector (CN39)
Table A.7: VGA connector (CN39)
Pin
Signal
1
RED
2
GREEN
3
BLUE
4
N/A
5
GND
6
GND
7
GND
8
GND
9
N/A
10
GND
11
N/A
12
SPDAT
13
HSYNC
14
VSYNC
15
SPCLK
PPC-L128T User Manual
26
Appendix A I/O Pin Assignments
A.8 PCI Bus connector (CN18)
Figure A.1 PCI connector
27
PPC-L128T User Manual
Table A.8: PCI pin assignments
Pin
Signal
Pin
Signal
A1
IOCHK
B1
GND
A2
SD7
B2
RST
A3
SD6
B3
VCC
A4
SD5
B4
IRQ9
A5
SD4
B5
-5 V
A6
SD3
B6
DRQ2
A7
SD2
B7
-12 V
A8
SD1
B8
OWS
A9
SD0
B9
+12 V
A10
IORDY
B10
GND
A11
AEN
B11
SMW
A12
SA19
B12
SMR
A13
SA18
B13
IOW
A14
SA17
B14
IOR
A15
SA16
B15
DACK3
A16
SA15
B16
DRQ3
A17
SA14
B17
DACk1
A18
SA13
B18
DRQ1
A19
SA12
B19
RFSH
A20
SA11
B20
SCLk
A21
SA10
B21
IRQ7
A22
SA9
B22
IRQ6
A23
SA8
B23
IRQ5
A24
SA7
B24
IRQ4
A25
SA6
B25
IRQ3
A26
SA5
B26
DACk2
A27
SA4
B27
TC
A28
SA3
B28
ALE
A29
SA2
B29
VCC
A30
SA1
B30
OSC
A31
SA0
B31
GND
PPC-L128T User Manual
28
Appendix A I/O Pin Assignments
A.9 PCI Express Bus connector (CN16)
Table A.9: PCIExpress pin assignments
Signal
Pin
Pin
Signal
GND
A1
B1
+V12
+V12
A2
B2
+V12
+V12
A3
B3
+V12
GND
A4
B4
GND
NC
A5
B5
SMB_CLK
NC
A6
B6
SMB_DATA
NC
A7
B7
GND
NC
A8
B8
+V3.3
+V3.3
A9
B9
NC
+V3.3
A10
B10
+V3.3SB
PLTRST#
A11
B11
PCIE_WAKE#
GND
A12
B12
NC
CLK_PCIE+
A13
B13
GND
CLK_PCIE-
A14
B14
PCIE_TX+
GND
A15
B15
PCIE_TX-
PCIE_RX+
A16
B16
GND
PCIE_RX-
A17
B17
PRSNT#
GND
A18
B18
GND
29
PPC-L128T User Manual
A.10 How to setup Teaming function on PPC-L128/
L157
A.10.1Team together
Step 1. PPC-L128/L157 supports dual LAN function with each 1Gbps speed.
PPC-L128T User Manual
30
Step 3. Turn to Team page. Here you can create a new team or add to team. Click
Create New Team.
31
PPC-L128T User Manual
Appendix A I/O Pin Assignments
Step 2. First, choose 1 LAN and open the properties panel. Then click on the Configure button.
Step 4. Name your team, and select the mode “Basic”.
Step 5. Continue anyway.
Step 6. The team has been created.
PPC-L128T User Manual
32
33
PPC-L128T User Manual
Appendix A I/O Pin Assignments
Step 7. Open the properties of another LAN, click “Add to Team” button.
Step 8. Choose the team this LAN should join in.
Step 9. Now two LAN become one team with 2Gbps.
PPC-L128T User Manual
34
Appendix A I/O Pin Assignments
A.10.2Dismiss!
Step 1. Open the configure page of teaming LAN. Two team members will show
inside.
35
PPC-L128T User Manual
Step 2. Choose the team member you want to kick out. Then click Remove Adapter
button.
Step 3. If you want to dismiss whole team. Click the Remove Team button and the
team will be not available anymore.
PPC-L128T User Manual
36
Appendix A I/O Pin Assignments
A.10.3TESTING
Step 1. Copy a big file to your disk through teaming LAN.
Step 2. Unplug one cable. And the transmission of file still alive. Teaming function
works!!
37
PPC-L128T User Manual
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2009
Download PDF