Installation Instructions READ BEFORE INSTALLING UNIT OPP Window Mounting (5K~6.5K BTU)

Installation Instructions READ BEFORE INSTALLING UNIT OPP Window Mounting (5K~6.5K BTU)
Installation Instructions
READ BEFORE INSTALLING UNIT
OPP Window Mounting (5K~6.5K BTU)
7RDYRLGULVNRISHUVRQDOLQMXU\SURSHUW\GDPDJHRUSURGXFWGDPDJHGXHWRWKHZHLJKWRIWKLVGHYLFHDQGVKDUS
edges that may be exposed:
$LUFRQGLWLRQHUVFRYHUHGLQWKLVPDQXDOSRVHDQH[FHVVLYHZHLJKWKD]DUG7ZRRUPRUHSHRSOHDUHQHHGHGWR
PRYHDQGLQVWDOOWKHXQLW7RSUHYHQWLQMXU\RUVWUDLQXVHSURSHUOLIWLQJDQGFDUU\LQJWHFKQLTXHVZKHQPRYLQJXQLW
&DUHIXOO\LQVSHFWORFDWLRQZKHUHDLUFRQGLWLRQHUZLOOEHLQVtalled. Be sure it will support the weight of the unit over
an extended period of time.
+DQGOHDLUFRQGLWLRQHUZLWKFDUH:HDUSURWHFWLYHJORYHVZKHQHYHUOLIWLQJRUFDUU\LQJWKHXQLW$92,'WKHVKDUS
PHWDOILQVRQIURQWDQGUHDUFRLOV
0DNHVXUHDLUFRQGLWLRQHUGRHVQRWIDOOGXULQJLQVWDOODWLRQ
NOTE:
Mounting Hardware
6$9(&$5721DQGWKHVH,167$//$7,21
,16758&7,216IRUIXWXUHUHIHUHQFH7KHFDUWRQLV
the best way to store unit during winter, or when not
in use.
'212786($1<6&5(:627+(57+$1
7+26(63(&,),('+(5(
Qty.
ƎVFUHZV
7
ORFNIUDPH
2
(For Wooden windows)
ORFNIUDPH
2
)RU9LQ\O&ODGZLQGRZs)
)256$)(7<5($62167+(7235$,/0867%(
6(&85(/<)$67(1(':,7+$//)285
6&5(:6
VDVKORFN
1
weather seals
5
Ǝ;Ǝ;Ǝ
window sash seal foam
6RPHDVVHPEO\LVUHTXLUHG3OHDVHUHDGWKHVHLQVWUXFWLRQV
FDUHIXOO\
Qty.
Top Rail Hardware
1
722/61(('('
Ǝ6FUHZ
4
3KLOLSV6FUHZGULYHU
Top Rail
1
'ULOO,ISLORWKROHVDUHQHHGHG
Before installing, the top rail must be assembled on the unit.
$5HPRYHWKHDLUFRQGLWLRQHUIURPWKHFDUWRQDQGSODFHRQDIODWVXUIDFH
%5HPRYHWRSUDLOIURPWKHUHDURIWKHSDFNDJLQJPDWHULDODVVKRZQLQ)LJ$
C. Align the hole in the top rail with those on the top of the unit as shown in Fig. B
'6HFXUHWKHWRSUDLOWRWKHXQLWZLWKWKHƎ6FUHZVDVVKRZQLQ)LJ&
Top Rail
Fig. A
Fig. B
Fig. C
3DFNDJLQJ
2020211A0669
1
How to Install
Installation
LEFT + RIGHT FILLER PANEL ASSEMBLY
NOTE: Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear of (5/16”).
This is necessary for proper condensed water utilization and drainage. If you are not using the Side Panels
for any reason, this pitch to the rear must be maintained!
Place unit on floor, a bench or a table. There is a Left and Right side Filler Panels - be sure to use the proper
panel for each side. When installed, the flange for securing the panel in place to the window sill will be facing
into the room.
A. Hold the side Panel in one hand and gently pull back the center to free the open end. See FIG. 1.
B. Slide the free end “T” section of the panel directly into the cabinet as shown in FIG. 2. Slide the panel down. Be
sure to leave enough space to slip the top and bottom of the frame into the rails on the cabinet.
C. Once the panel has been installed on the side of the cabinet, make sure it sits securely inside the frame channel by
making slight adjustments. Slide the top and bottom ends of the frame into the top and bottom rails of the cabinet. See
FIG. 3.
D. Slide the panel all the way in and repeat on the other side.
FIG. 1
FIG. 2 “T” section
FIG. 3 Top Rail
Bottom Rail
Your air conditioner is designed to install in standard double hung windows with opening widths of 23 to 36 inches
(584 mm to 914 mm) (FIG. 4A , FIG. 4B).
Lower sash must open sufficiently to allow a clear vertical opening of 13 inches (330 mm ). Side louvers and the rear of
the air conditioner must have clear air space to allow enough airflow through the condenser, for heat removal. The rear
of the unit must be outdoors, not inside a building or garage.
Fig. 4B
Fig. 4A
INNER
WINDOW SILL
ƎPLQ
330 mm
ƎPLQ
330 mm
INNER
WINDOW SILL
INTERIOR
WALL
Vinyl-Clad Windows
Wooden Windows
Storm Window:
SASH
If the air conditoner is blocked by Storm Window, add wood as
shown in FIG. 5, or remove storm window before air conditioner
is installed.
If Storm Window Frame must remain, be sure the drain holes or
slots are not caulked or painted shut. Accumulated Rain Water
or Condensation must be allowed to drain out.
2
Storm window
frame or other
obstruction.
1-1/2” min
(38 mm)
FIG. 5
Board
thickness as
required, for
proper pitch to
rear, along
entire sill.
Fasten with
nails or screws.
How to Install
Installation
Keep a firm grip on the air conditioner, carefully place the unit into the window opening so the bottom of the air
conditioner frame is against the window sill (FIG. 6A & FIG. 6B). Carefully close the window behind the top rail
of the unit.
FIG. 6B
FIG. 6A
INSIDE
OUTSIDE
INSIDE
OUTSIDE
Wooden Windows
Vinyl-Clad Windows
Extend the side panels out against the window frame (FIG. 7A for wooden windows), (FIG. 7B for Vinyl-Clad
windows).
FIG. 7A
FIG. 7B
window
frame
Place the frame lock between the frame extensions and the window sill as shown (FIG. 8A for wooden
windows), (FIG. 8B for Vinyl-Clad windows).
FIG. 8A
wooden windows:
FIG. 8B
Vinyl-Clad windows:
Drive locking screws:
A: For wooden windows:
'ULYHƎPPORFNLQJVFUHZVWKURXJKWKHIUDPHORFNDQGLQWRWKHVLOO),*$NOTE:To prevent
ZLQGRZVLOOIURPVSOLWWLQJGULOOƎPPSLORWKROHVEHIRUHGULYLQJVFUHZV'ULYHƎPPORFNLQJVFUHZV
WKURXJKIUDPHKROHVLQWRZLQGRZVDVK),*%
B: For Vinyl-Clad windows:
'ULYHƎPPORFNLQJVFUHZVWKURXJKWKHIUDPHORFNDQGLQWRWKHZLQGRZVDVK),*%NOTE:Before
driving the screws, use a drill to drill 5 holes through the holes in the frame lock and frame extensions into the
ZLQGRZVVDVKDVVKRZQ),*%
),*$
),*%
3
Installation
7RVHFXUHORZHUVDVKLQSODFHDWWDFKULJKWDQJOHVDVKORFNZLWKƎPPVFUHZDVVKRZQ),*
NOTE: It is difficult to lock the windows with the sash lock for Vinyl-Clad windows, so you can use lock by
window itself.
Cut foam window seal and insert it into the space between the upper and lower sashes (FIG. 11).
FIG. 10
FIG. 11
FOAM SEAL
After the completion of the installation, please check the machine’s lean as shown (FIG. 12A & FIG. 12B). It’s
necessary for proper condensed water utilization and drainage.
FIG. 12A
FIG. 12B
H
H
INSIDE
OUTSIDE
INSIDE
OUTSIDE
H=H1-H2 DERXWƎaƎ
Bottom Rail
H
about
ƎaƎ
H1
Wooden Window
Trim the weather seal Ǝ;Ǝ;Ǝ with a proper length,
peel off the protective backing and plug any gaps if needed
DVVKRZQ),*
Removing the air conditioner From Window
Turn the air conditioner off, and disconnect power cord.
Remove sash seal from between windows, and unscrew sash lock.
Remove screws installed through frame and framelock.
Close (slide) side panels into frame.
Keeping a firm grip on air conditioner, raise sash and
carefully remove.
Be careful not to spill any condensate water while lifting
unit from window. Store parts WITH air conditioner.
4
Bottom Rail
H2
Vinyl-Clad Window
),*
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising