IE-MediaChassis/2 (AC) Operation Manual
IE-MediaChassis/2 (AC)
Operation Manual
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the
Class B limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department
of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de
classe B prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.
Warranty
Limited Lifetime Warranty
Effective for products of B&B Electronics shipped on or after May 1, 2013, B&B
Electronics warrants that each such product shall be free from defects in material
and workmanship for its lifetime. This limited lifetime warranty is applicable solely
to the original user and is not transferable.
This warranty is expressly conditioned upon proper storage, installation,
connection, operation and maintenance of products in accordance with their
written specifications.
Pursuant to the warranty, within the warranty period, B&B Electronics, at its
option will:
1. Replace the product with a functional equivalent;
2. Repair the product; or
3. Provide a partial refund of purchase price based on a depreciated value.
Products of other manufacturers sold by B&B Electronics are not subject to any
warranty or indemnity offered by B&B Electronics, but may be subject to the
warranties of the other manufacturers.
Notwithstanding the foregoing, under no circumstances shall B&B Electronics
have any warranty obligations or any other liability for: (i) any defects resulting
from wear and tear, accident, improper use by the buyer or use by any third party
except in accordance with the written instructions or advice of the B&B
Electronics or the manufacturer of the products, including without limitation surge
and overvoltage conditions that exceed specified ratings, (ii) any products which
have been adjusted, modified or repaired by any party other than B&B
Electronics or (iii) any descriptions, illustrations, figures as to performance,
drawings and particulars of weights and dimensions contained in the B&B
Electronics’ catalogs, price lists, marketing materials or elsewhere since they are
merely intended to represent a general idea of the products and do not form part
of this price quote and do not constitute a warranty of any kind, whether express
or implied, as to any of the B&B Electronics’ products.
THE REPAIR OR REPLACEMENT OF THE DEFECTIVE ITEMS IN
ACCORDANCE WITH THE EXPRESS WARRANTY SET FORTH ABOVE IS
ii
B&B ELECTRONIC’ SOLE OBLIGATION UNDER THIS WARRANTY. THE
WARRANTY CONTAINED IN THIS SECTION SHALL EXTEND TO THE
ORIGINAL USER ONLY, IS IN LIEU OF ANY AND ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, AND ALL SUCH WARRANTIES AND INDEMNITIES
ARE EXPRESSLY DISCLAIMED, INCLUDING WITHOUT LIMITATION (I) THE
IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND
OF MERCHANTABILITY AND (II) ANY WARRANTY THAT THE PRODUCTS
ARE DO NOT INFRINGE OR VIOLATE THE INTELLECTUAL PROPERTY
RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL B&B ELECTRONICS
BE LIABLE FOR LOSS OF BUSINESS, LOSS OF USE OR OF DATA
INTERRUPTION OF BUSINESS, LOST PROFITS OR GOODWILL OR OTHER
SPECIAL, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES.
B&B ELECTRONIC SHALL DISREGARD AND NOT BE BOUND BY ANY
REPRESENTATIONS, WARRANTIES OR INDEMNITIES MADE BY ANY
OTHER PERSON, INCLUDING WITHOUT LIMITATION EMPLOYEES,
DISTRIBUTORS, RESELLERS OR DEALERS OF B&B ELECTRONIC WHICH
ARE INCONSISTENT WITH THE WARRANTY, SET FORTH ABOVE.
iii
Table of Contents
FCC Radio Frequency Interference Statement .................................................. ii
Warranty ............................................................................................................. ii
About the IE-MediaChassis/2 (AC) .................................................................... 0
Installing the IE-MediaChassis/2 (AC) ............................................................... 0
Configuring and Installing Modules.................................................................... 2
Rack Mount Precautions ................................................................................... 2
B&B Electronics Technical Support ................................................................... 3
Specifications .................................................................................................... 3
Electrostatic Discharge Precautions .................................................................. 5
Safety Certifications........................................................................................... 6
iv
About the IE-MediaChassis/2 (AC)
The IE-MediaChassis/2 (AC) is a stand-alone chassis for use with iMcV modules.
As an unmanaged chassis, the IE-MediaChassis/2 (AC) supports two single-wide
or one dual-wide iMcV module. All iMcV modules, with the exception of the
SNMP management card, will function properly in this chassis.
The IE-MediaChassis/2 (AC) contains an internal AC power supply. It supports
an extended temperature of -20° to +70°C
The IE-iMediaChassis/2 (AC) includes a temperature triggered fan. When the
internal temperature of the chassis reaches 86° F (30° C) the fan is activated. As
the temperature increases the fan drive duty cycle adjusts to increase the fan
speed. You can test the fan operation by depressing the fan test switch on the
back of the chassis.
Installing the IE-MediaChassis/2 (AC)
Use the IE-MediaChassis/2 (AC) as a table-top chassis, mount in a rack mount
shelf, or mount it to a wall surface (brackets are not required).
1.
Install the IE-MediaChassis/2 (AC) by placing it on a flat surface.
2.
If mounting on a Rackmount shelf, align screw holes and secure with
screws.
The rack-mount shelf is sold separately. To purchase the rack-mount shelf (part
number 895-39949); visit the B&B Electronics’ Product Accessories page:
Rackmounting requires a rackmount shelf for mounting up to three units side
by side.
3.
If mounting the chassis on a wall, place two #10 panhead screws (not
supplied) on the wall the distance of the holes on the chassis, and then
hang the unit on the screws.
4.
Attach the cables between the chassis and the device that will be
interconnected, and then plug the unit into a reliable, filtered power
source.
Configuring and Installing Modules
B&B Electronics recommends turning the chassis power off before proceeding.
1.
To install an iMcV module, slide the module into the chassis until the
module is firmly seated in the backplane.
2.
Secure the module to the chassis by tightening the captive thumb screw
on the iMcV module.
3.
Attach the network cables between the iMcV module and other devices
that will be interconnected.
4.
Plug the chassis into the AC power source.
Rack Mount Precautions
1.
Elevated Operating Ambient - If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment
may be greater than room ambient. Therefore, consideration should be
given to installing the equipment in an environment compatible with the
maximum ambient temperature (Tma) specified by the manufacturer.
2.
Reduced Air Flow - Installation of the equipment in a rack should be
such that the amount of air flow required for safe operation of the
equipment is not compromised.
3.
Mechanical Loading - Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven
mechanical loading.
4.
Circuit Overloading - Consideration should be given to the connection
of the equipment to the supply circuit and the effect that overloading of
the circuits might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be
used when addressing this concern.
5.
Reliable Earthing - Reliable earthing of rack-mounted equipment
should be maintained. Particular attention should be given to supply
connections other than direct connections to the branch circuit (e.g.
use of power strips).
B&B Electronics Technical Support
International Headquarters
B&B Electronics Mfg. Co. Inc.
707 Dayton Road
Ottawa, IL 61350 USA
Phone (815) 433-5100 -- General Fax (815) 433-5105
Website: www.bb-elec.com
European Headquarters
B&B Electronics
Westlink Commercial Park
Oranmore, Co. Galway, Ireland
Phone +353 91-792444 -- Fax +353 91-792445
Website: www.bb-europe.com
Specifications
Environmental:
Operating Temperature: -4° F to 158° F (-20° C 70° C)
Storage Temperature: -40° F to 185° F (-40° C to 85° C)
Humidity: 5 to 95% (non-condensing)
AC Power Supply:
AC Input: 100-240 V AC ±10%, 50/60 Hz, 1-0.5A
Dimensions:
2.23”H x 4.75”W x 7.30”D (5.7 cm H x 12.1 cm W x 18.6 cm D)
Heat Generation:
51 BTU/hr. maximum
Fan turns on if the internal temperature exceeds 86° F (30° C)
Electrostatic Discharge Precautions
Electrostatic discharge (ESD) can cause damage to your add-in modules.
Always observe the following precautions when installing or handling an add-in
module or any board assembly.
1.
Do not remove unit from its protective packaging until you’re ready to install
it.
2.
Wear an ESD wrist grounding strap before handling any module or
component. If you do not have a wrist strap, maintain grounded contact with
the system unit throughout any procedure requiring ESD protection.
3.
Hold boards by the edges only; do not touch the electronic components or
gold connectors.
4.
After removal, always place the boards on a grounded, static-free surface,
ESD pad or in a proper ESD bag. Do not slide the board over any surface.
WARNING! Integrated circuits and fiber optic components are
extremely susceptible to electrostatic discharge damage. Do
not handle these components directly unless you are a qualified
service technician and use tools and techniques that conform to
accepted industry practices.
Safety Certifications
UL/CUL: Listed to Safety of Information Technology Equipment, including
Electrical Business Equipment.
CE: The products described herein comply with the Council Directive on
Electromagnetic Compatibility (89/336/EEC) and the Council
Directive on Electrical Equipment Designed for use within Certain
Voltage Limits (73/23/EEC). Certified to Safety of Information
Technology Equipment, Including Electrical Business Equipment.
For further details, contact B&B Electronics.
European Directive 2002/96/EC (WEEE) requires that any equipment that bears
this symbol on product or packaging must not be disposed of with unsorted
municipal waste. This symbol indicates that the equipment should be disposed
of separately from regular household waste. It is the consumer’s responsibility to
dispose of this and all equipment so marked through designated collection
facilities appointed by government or local authorities. Following these steps
through proper disposal and recycling will help prevent potential negative
consequences to the environment and human health. For more detailed
information about proper disposal, please contact local authorities, waste
disposal services, or the point of purchase for this equipment.
© 2013 B&B Electronics. All rights reserved.
The information in this document is subject to change without notice. B&B Electronics assumes no responsibility for
any errors that may appear in this document. IE-MediaChassis/2 is a trademark of B&B Electronics. Other brands
or product names may be trademarks and are the property of their respective companies.
Document IE-MediaChassis 2AC
May 2014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement