sls-manual-47-67sat
Instruction Manual
LS47SAT & LS67SAT speakers
Introduction
Thank you for purchasing SLS Speakers. When properly installed,
these speakers will provide you with years of outdoor entertainment
pleasure. To get the most out of your new speakers, please read this
manual thoroughly before you begin installation.
Box Contents
SLS Satellite box contains:
(1) Satellite speaker
(2) Silicone Filled Wire Nuts
Satellite Location Selection
The SLS is designed to deliver a seamless, evenly dispersed sound
field in an ‘open air’ environment. An array of multiple Satellite
speakers and Subwoofers should be strategically placed to minimize
‘hot spots’ and ‘nulls’ as you move around the outdoor entertainment
area. See Figure 1.
LS47SAT
Landscape Series Satellite Speaker
As a general guideline, (1) Satellite will cover about 250
square feet of listening area
Select locations for the satellites that are as close as possible to the
same distance from the main listening area. When possible use high
and low locations to centralize the acoustic stage. See figure 2
Amplifier Power Planning
The maximum number of satellites and subwoofers that can be
used in a system will depend on the quantity of amplifier power
available.
Before beginning an installation use the chart below to calculate
the amplifier power your installation will require. Multiple
amplifiers may be required in large installations.
Wattage Calculator
Model
qty. ch1 qty. ch2 x
watts
LS47SAT
x
25
LS67SAT
x
25
LS10SUB
x
100
LS12SUB
x
100
Figure 1
total ch1
total ch2
total
20%
head
room
TOTAL MINIMUM WATTAGE
Amplifier Selection
For systems up to 500w per channel use the CROWN CDI 1000
For systems up to 800w per channel use the CROWN CDI 2000
For systems up to 1000w per channel use the CROWN CDI 4000
Figure 2
1
Satellite Installation
1. Once Locations have been established, choose the appropriate
mounting accessories for the project. PLEASE NOTE: Always
use a #3 Phillips head screwdriver when fine tuning the height
adjustment screw.
4. Dig a 4” – 5” deep trench to run the speaker wires in.
5. Run the wire through the trench from your amplifier to the first
speaker location.
6. Connect the direct burial wire to each speaker wire, connections
should be made with either silicone filled wire connectors or
appropriate junction boxes. See figure 3.
• For applications on flat surfaces, such as the side of a building
or structure, use the SM1 Round Surface Mount. See Instruction
Manual included with accessory for precise instructions
Waterproof
Wire Nuts
• For placement directly into the ground, use the GS9 ABS inground stake for the LS47SAT, and/or the GP19 PVC Ground
Post for the LS67SAT. See Instruction Manual included with
accessory for precise instructions
Positive
Negative
+
-
Twist
Wires
Together
• For in-tree Mounting, use the TSMJB Tree / Surface Mounting
Junction Box. See Instruction Manual included with accessory
for precise instructions
From Speaker
To Amplifier
Figure 3
2. Once the accessories have been mounted at the desired
locations, mount the satellites by threading the mounting shaft
into the corresponding opening of the accessory,
IMPORTANT: Be sure not to let any stray ‘+’ and ‘–’
strands touch each other. Touching strands can cause a
short-circuit that could damage your amplifier.
Note: Attention must be paid to the electrical leads to
avoid nicks and cuts that might short the system.
3. Prepare individual leads to be connected to main leads.
Note: Confirm that you have connected speaker “+” to
amplifier “+” and speaker “–” to amplifier “–”.
Connecting to the Amplifier
70 volt audio systems allow for speakers to be daisy chained
together. In a typical system with one zone of audio you simply run a
stereo or 4 conductor wire from the amplifier to the closest speaker.
Once you have designated your first speaker as either left or right,
continue alternating the wires between the left and right channels
creating a daisy chain of stereo satellites. The Subwoofer can be
wired anywhere in the chain. See figure 4.
7. After all the speakers connections are completed, connect the
wires to your amplifier. See Figure 4 for reference.
8. Turn your amplifier on and test the system with your favorite
music. If the speakers are operating properly, refill the wire
trench and enjoy your new speakers.
Note: Sonance strongly recommends the use of 14
gauge or larger direct burial grade wire.
Caution: The amplifier should not be connected to AC
power until all connections are completed. High power
70 volt amplifiers present a serious shock hazard. Do
not connect speaker wires to the amplifier until all other
connections are completed.
SLS Wiring Diagram 70V
Crown CDi Series Amplifier
LS47SATs & LS10SUB or LS67SATs & LS12SUB
Note: The subwoofer can
be connected at any point
in the daisy chain.
Left
Right
Left
Configuration: 4 SATs to 1 SUB or up to 8 SATs to 1 SUB
Figure 4
2
Right
Expandable
Specifications
LS47SAT
LS67SAT
.75” (19mm) polycarbonate dome
Tweeter:
.75” (19mm) polycarbonate dome
Woofer:
3.5” (89mm) polypropylene cone with
a rubber surround
Woofer:
6” (152mm) polypropylene cone with
a rubber surround
Frequency Response: 80Hz - 20KHz ±3dB
Frequency Response: 60Hz - 20KHz ±3dB
Power Required:
25 watts
Power Required:
25 watts
Enclosure Material:
Non-corrosive sealed enclosure
Enclosure Material:
Non-corrosive sealed enclosure
Listening Area:
60˚ coverage, 10’ to 50’ recommended
Listening Area:
60˚ coverage, 10’ to 50’ recommended
Speaker Input: 70 volts
Speaker Input: 70 volts
Dimensions:
6.5”L x 4.125” Dia
(165mm x 105mm)
Dimensions:
10.25” L x 6.70” Dia
(260mm x 170mm)
Shipping Weight:
2.8 lbs (1.34 kg)
Shipping Weight:
6 lbs (2.7 kg)
(6.70")170.00 mm
(4.125") 105.00mm
(6.500") 165.00mm
10.250" (260.00mm)
(6.500") 165.00mm
(6.70")170.00 mm
SECTION B-B
SCALE 1 : 1.5
10.250" (260.00mm)
(4.125") 105.00mm
Tweeter:
3
LIMITED FIVE (5) YEAR WARRANTY
Sonance warrants to the first end-user purchaser that this Sonance-brand product (“Product”), when purchased from an authorized Sonance
Dealer/Distributor, will be free from defective workmanship and materials for the period stated below. Sonance will at its option and expense
during the warranty period, either repair the defect or replace the Product with a new or remanufactured Product or a reasonable equivalent.
EXCLUSIONS
TO THE EXTENT PERMITTED BY LAW, THE WARRANTY SET FORTH ABOVE IS IN LIEU OF, AND EXCLUSIVE OF, ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED BY SONANCE.
ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY,
IMPLIED WARRANTY OF FITNESS FOR USE, AND IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE
SPECIFICALLY EXCLUDED.
No one is authorized to make or modify any warranties on behalf of Sonance. The warranty stated above is the sole and exclusive remedy
and Sonance’s performance shall constitute full and final satisfaction of all obligations, liabilities and claims with respect to the Product.
IN ANY EVENT, SONANCE SHALL NOT BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL, ECONOMIC, PROPERTY,
BODILY INJURY, OR PERSONAL INJURY DAMAGES ARISING FROM THE PRODUCT, ANY BREACH OF THIS WARRANTY
OR OTHERWISE.
This warranty statement gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not
allow the exclusion of implied warranties or limitations of remedies, so the above exclusions and limitations may not apply. If your state does
not allow disclaimer of implied warranties, the duration of such implied warranties is limited to period of Sonance’s express warranty.
Your Product Model and Description: SLS LS47SAT or LS67SAT speakers.
Warranty Period for this Product: Five (5) years from the date on the original sales receipt or invoice or other satisfactory proof of purchase.
Additional Limitations and Exclusions from Warranty Coverage: The warranty described above is non-transferable, applies only to the initial
installation of the Product, does not include installation of any repaired or replaced Product, does not include damage to allied or associated
equipment which may result for any reason from use with this Product, and does not include labor or parts caused by accident, disaster,
negligence, improper installation, misuse (e.g. overdriving the amplifier or speaker, excessive heat or cold or humidity, outdoor installation),
or from service or repair which has not been authorized by Sonance. Obtaining Authorized Service: To qualify for the warranty, you must
contact your authorized Sonance Dealer/Installer or call Sonance Customer Service at (800) 582-0772 within the warranty period, must
obtain a return merchandise number (RMA), and must deliver the Product to Sonance shipping prepaid during the warranty period, together
with the original sales receipt, or invoice or other satisfactory proof of purchase.
©2012 Sonance. All rights reserved. Sonance is a registered trademarks of Dana Innovations. Patent pending.
Due to continuous product improvement, all features and specifications are subject to change without notice.
For the latest Sonance product specification information visit our website: www.sonance.com
SONANCE • 212 Avenida Fabricante • San Clemente, CA 92672-7531 USA
(800) 582-7777 or (949) 492-7777 • FAX: (949) 361-5151 • Technical Support: (800) 582-0772
www.sonance.com
33-5513
110712
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising