Extron electronics TP T 15HD 45 User`s manual

Extron electronics TP T 15HD 45 User`s manual
im Vertrieb von
CAMBOARD Electronics
User’s Manual
TP T 15HD 45 and TP T A 45
www.extron.com
Extron Electronics, USA
Extron Electronics, Europe
Extron Electronics, Asia
Extron Electronics, Japan
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
www.camboard.de
© 2005 Extron Electronics. All rights reserved.
Tel. 07131 911201
Fax 07131 911203
Twisted Pair Video and Audio Transmitters
68-924-01 Rev. C
05 05
[email protected]
im Vertrieb von
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions
in the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product's enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation
et la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de
pouvoir les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et
consignes marqués sur le matériel ou présentés dans la documentation
utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni
d’outils non recommandés par le fabricant du matériel car cela
risquerait de poser certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau
durchlesen und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario sobre
instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de
operación y seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad
para futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones
marcadas en el equipo o en la documentación del usuario, deben ser
obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
www.camboard.de
CAMBOARD Electronics
FCC Class B Notice
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main
power system with a grounded (neutral) conductor. The third (grounding) pin is
a safety feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all
power cords from the rear of the equipment, or the desktop power module (if
detachable), or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to
be stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly replaced.
Replace it only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer's
instructions.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that the interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation
principale comportant un fil de terre (neutre). Le troisième contact (de mise à la
terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la
désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du
module d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient
pas écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne
doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le
retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices,
ceux-ci servent à empêcher les composants internes sensibles de surchauffer. Ces
ouvertures ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d'explosion s'll y a remplacment incorrect de la
batterie. Remplacer uniquement avec une batterie du meme type ou d'un ype
equivalent recommande par le constructeur. Mettre au reut les batteries usagees
conformement aux instructions du fabricant.
• Consult the dealer or an experienced radio/TV technician for help.
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be
used with the unit to ensure compliance.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a
period of three years from the date of purchase. In the event of malfunction during the
warranty period attributable directly to faulty workmanship and/or materials, Extron
Electronics will, at its option, repair or replace said products or components, to whatever
extent it shall deem necessary to restore said product to proper operating condition,
provided that it is returned within the warranty period, with proof of purchase and
description of malfunction to:
USA, Canada, South America,
and Central America:
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit
einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der
dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar.
Diese sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen,
sollten Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen
Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht
im Weg liegen und niemand darauf treten kann oder Objekte darauf- oder
unmittelbar dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem
Servicepersonal durchgeführt werden. Die internen Komponenten des Gerätes
sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks versuchen Sie in
keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die
Gefahr eines elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse
aufweist, dienen diese zur Vermeidung einer Überhitzung der empfindlichen
Teile im Inneren. Diese Öffnungen dürfen niemals von anderen Objekten
blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird.
Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen
Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor
neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no
puentearia ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la
acometida de alimentación eléctrica al equipo, desenchufar todos los cables de
alimentación en el panel trasero del equipo, o desenchufar el módulo de
alimentación (si fuera independiente), o desenchufar el cable del receptáculo de
la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se
deben instalar en lugares donde no sean pisados ni apretados por objetos que se
puedan apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para
evitar riesgo de electrocución, no intentar personalmente la reparación/
mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar
expuesto a voltajes peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Extron Electronics
1001 East Ball Road
Anaheim, CA 92805, USA
Asia:
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Europe, Africa, and the Middle East:
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Japan:
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or non-Extron
authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400 (Asia),
or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This will begin
the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect to
the product and its quality, performance, merchantability, or fitness for any particular use.
In no event will Extron Electronics be liable for direct, indirect, or consequential damages
resulting from any defect in this product even if Extron Electronics has been advised of such
damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Tel. 07131 911201
Fax 07131 911203
[email protected]
im Vertrieb von
CAMBOARD Electronics
Quick Start Guide — TP T 15HD 45 / A 45
CAUTION
Installation and service must be performed by authorized
personnel only. These units must be installed in
accordance with national and local electrical codes.
Step 1
Power off all devices and disconnect them from the power source.
Step 2
Connect the UTP cable from the receiver to the 8-pin connector on
the TP T 15HD 45. To wire the connector, see Rear Panel Connectors
in chapter 2 for the pinout table.
CAUTION
Do not connect the TP T 15HD 45 to a computer data or
telecommunications network.
Step 3
Connect the external power supply to the transmitter.
Step 4
Using the 15-pin front panel HD connector, attach a computer input
to the transmitter and a display output to the receiver. See the
example application diagram below.
Projector
Mounting
Bracket
Mounting
Bolt
AV INPUT
Extron
TP R 15HD A
OUTPUT
RGB
Twisted Pair
Receiver
L
AUDIO
R
C
SYNC
SOG
C
VIDEO
N/C
POWER
15V
.34A MAX
CAT 5/6 or
Extron
Skew-Free TM
UTP Cable
Up to 500 feet
Ceiling
Projector-mountable
Extron
TP T A 45
TP T 15HD 45
IO
AUD
T
INPU
ER
PUT
COM
T
INPU
Twisted Pair
Transmitters
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
[email protected]
TP T 15HD 45 and
TP T A 45 • Quick Start Guide
QS-1
imStart
Vertrieb
von— TP T 15HD/A 45, cont’d
Quick
Guide
CAMBOARD Electronics
Table of Contents
Chapter 1 • Introduction .......................................................... 1-1
Step 5
If the TP T A 45 is being installed, connect the TP T A 45 to the
TP T 15HD 45. See Rear Panel Connectors in chapter 2.
Features ...................................................................................... 1-2
Chapter 2 • Installation ............................................................. 2-1
The TP T 15HD 45 may be used as a stand-alone, video-only
module without the TP T A 45.
The TP T A 45 derives its power from the TP T 15HD 45.
Rear Panel Connectors ........................................................ 2-2
Front Panel Connectors and Indicators ...................... 2-5
Cabling and Setup ................................................................. 2-5
Step 6
Connect and power up all input and output devices, then apply
power to the TP T 15HD 45 power supply and test for the display
and/or audio outputs. If a problem is encountered, check all
connections before proceeding further.
Compatibility with other Extron products ............................ 2-6
Cable testing .......................................................................... 2-7
Skew delay problems ............................................................. 2-7
Mounting ................................................................................ 2-8
Step 7
Appendix • Reference Information .................................. A-1
If the previous display and/or audio test was successful, power off
and disconnect all equipment, detach cables, and install the TP T
15HD 45 and TP T A 45 (if installed) modules. See Mounting in
chapter 2.
Specifications ......................................................................... A-2
Parts Lists ................................................................................. A-5
Included parts ........................................................................ A-5
Optional accessories ............................................................. A-5
If the transmitter is to be wall-mounted and the power supply
will be inaccessible, power must be applied to the
transmitter’s power supply before final mounting.
Step 8
All trademarks mentioned in this manual are the properties of their respective
owners.
Connect all device and power cables. Power up all input and output
devices, apply power to the transmitter and receiver, and test for the
display and/or audio.
68-924-01 Rev. C
05 05
QS-2
TPwww.camboard.de
T 15HD 45 and TP T A 45 • Quick Start Guide
Tel. 07131 911201
Fax 07131 911203
[email protected]
TP T 15HD 45 and
TP T A 45 • Table of Contents
i
imContents,
Vertrieb von
Table of
cont’d
CAMBOARD Electronics
TP T 15HD 45 and TP T A 45
1
Chapter One
Introduction
Features
ii
www.camboard.de
TP T
15HD 45 and TP T A 45 • Table of Contents
Tel. 07131 911201
Fax 07131 911203
[email protected]
im Vertrieb
von
Introduction,
cont’d
Introduction
CAMBOARD Electronics
The Extron TP T 15HD 45 twisted pair transmitter and the
matching TP T A 45 audio input module provide a system for
sending RGBHV, RGBS, RGsB, component, composite, or
S-video and stereo audio signals over Extron Skew-Free™ A/V
UTP cable or CAT 5/5e/6 UTP cable to a compatible TP or VTR
receiver. An external 12 VDC power supply provides power to
both the TP T 15HD 45 and the TP T A 45.
The TP T A 45 inputs unbalanced audio through a 3.5 mm stereo
phono jack and outputs digital audio to the TP T 15HD 45
transmitter.
The following table specifies the maximum recommended
transmission distances between the TP T 15HD 45 transmitter
and compatible Extron receivers at 60 Hz.
Video
format/
resolution
Recommended maximum Recommended maximum
range to VTR series
range to all other
and TP R 15HD A
Extron receivers
Composite*
800 feet
1000 feet
S-video*
800 feet
1000 feet
Component*
800 feet
1000 feet
640 x 480
500 feet
1000 feet
800 x 600
400 feet
800 feet
1024 x 768
300 feet
600 feet
1280 x 1024
200 feet
400 feet
1600 x 1200
150 feet
300 feet
TP T 15HD 45 and TP T A 45
2
Chapter Two
* VTR001 is not compatible with component, composite, or S-video.
Installation
It is possible to exceed the recommended distances,
however, image quality may be reduced.
Rear Panel Connectors
Features
• 45 mm opening compatibility — The TP T 15HD 45 and
TP T A 45 are designed to fit into a 45 mm mounting
frame that is popular throughout Europe. The plate may
be wall-mounted or floor box-mounted.
Front Panel Connectors and Indicators
Cabling and Setup
• Extron TP product compatibility — The TP T 15HD 45 and
TP T A 45 are compatible with several Extron TP receivers
and matrix switchers including the TP R 15HD A, TP R
BNC A, TP R BNC AV, TPX 88, TPX 88A, and the VTR
series (RGBHV and RGBS only).
1-2
TPwww.camboard.de
T 15HD 45 and TP T A 45 • Introduction
Tel. 07131 911201
Fax 07131 911203
[email protected]
im Vertrieb
von
Installation,
cont’d
Installation
CAMBOARD Electronics
AUDIO
AUDIO
1b
OUTPUT
1 2 3 4 5 6 7 8
12 VDC
.5A MAX.
4
2
AUDIO
AUDIO
The wire gauge should be 14 -22 AWG and the
maximum distance between the modules should not
exceed 25 feet.
12 VDC
.5A MAX.
3
2
Pin
A
+
+
Power Supply
Output Cord
Captive Screw
Direct Insertion Connector
The two power supply leads must be kept separated
while the power supply is plugged into an electrical
outlet. Remove power before wiring.
CAUTION
Power supply voltage polarity is critical. Incorrect
voltage polarity can damage the power supply and
the transmitter. Identify the power cord negative
lead by the ridges on the side of the cord.
When stripping the wire ends, please note that
stripped wire ends that are too short may pull out
from the captive screw connector and stripped wire
ends that are too long could possibly touch and
short together.
Signal
TIA/EIA T-568-A TIA/EIA T-568-B
Wire Color
Wire Color
1
red / vertical sync +
white-green
2
red / vertical sync -
green
orange
3
digital audio +
white-orange
white-green
4
green +
blue
blue
5
green -
white-blue
white-blue
6
digital audio -
orange
green
7
blue / horizontal sync +
white-brown
white-brown
8
blue / horizontal sync -
brown
brown
12 VDC
.5A MAX.
SECTION A–A
Video and audio output 8-pin spring force connector — Attach
a UTP cable from a TP receiver to the 8-pin spring force
connector. Wire this connector according to the following pin
assignment table.
Twisted Pair Pin Assignments
Power input captive screw connector — Connect the included
12 VDC external power supply to the 2-pole female direct
insertion captive screw connector.
A
2-2
-
Remove power before wiring.
The TP T 15HD 45 and the TP T A 45 share a single
power supply. Neither one can be remotely powered by
the attached receiver.
1b
AUDIO
Digital Audio Input Captive Screw
Direct Insertion Connector
Figure 2-1 — Rear panel views
1a
-
TP T A 45
TP T 15HD 45
1a
AUDIO
+
TP T A 45
TP T 15HD 45
+
Rear Panel Connectors
white-orange
T-568-A is recommended when using Extron UTP23SF
cable.
CAUTION
Do not connect the transmitter to a computer data
or telecommunications network.
Using the included tweeker tool and observing the correct
wiring colors in the previous table, insert the stripped wire ends
(see note below) of the twisted pairs into the spring force
connector, as shown in the following diagram.
Strip approximately 0.43" (1.1 cm) of insulation from
each individual wire on one end of a TP cable.
Captive screw digital audio input connector — Connect the
digital audio input cables from the TP T A 45 (if installed) to the
2-pole female direct insertion captive screw connector.
TP www.camboard.de
T 15HD 45 and TP T A 45 • Installation
Tel. 07131 911201
Fax 07131 911203
[email protected]
TP T 15HD
45 and TP T A 45 • Installation
2-3
im Vertrieb
von
Installation,
cont’d
CAMBOARD Electronics
Front Panel Connectors and Indicators
12345678
TP T 15HD 45
TP T A 45
1
1
COMPUTER
1&2
7&8
3
2
3&6 4&5
Twisted Wire Pairs
AUDIO
INPUT
INPUT
3
Power input captive screw connector — Connect power input
cables to the 2-pole female direct insertion captive screw
connector.
Figure 2-2 — Front panel views
1
Power LED indicator — The LED lights green whenever power
is applied.
2
15-pin HD video input connector — Connect
computer video input.
+
12 VDC
.5A MAX.
-
Power Input Captive Screw
Direct Insertion Connector
10
5
15
Digital audio output captive screw connector — Connect the
digital audio output cables to the 2-pole female direct insertion
captive screw connector.
+
-
6
11
Input only sync signals, no video
Female
signals, on the sync pins, 13 and 14.
For component video, use the R (R-Y) and R return pins
(pins 1 and 6), G (Y) and G return pins (pins 2 and 7),
and B (B-Y) and B return pins (pins 3 and 8).
For S-video, use the R, R return (C-chroma), G, and G
return (Y-luma) pins.
For composite video, use the G pin and the associated
return pin. For additional genlocked video signals, use
the R, B, and associated return pins.
The TP T 15HD 45 and TP T A 45 are only compatible
with the RGBHV and RGBS VTR series of receivers.
Remove power before wiring.
4
1
AUDIO
AUDIO
Digital Audio Output
Captive Screw Direct Insertion Connector
Remove power before wiring.
3
3.5 mm stereo mini jack input —
Connect unbalanced audio to this
stereo jack. Wire the male plug as
shown on the right.
Tip (L)
Ring (R)
Sleeve ( )
Input only analog and line level audio signals on this
connector.
Cabling and Setup
To install the TP T 15HD 45 and TP T A 45 models, follow these
steps:
2-4
TP www.camboard.de
T 15HD 45 and TP T A 45 • Installation
Tel. 07131 911201
Fax 07131 911203
[email protected]
TP T 15HD
45 and TP T A 45 • Installation
2-5
im Vertrieb
von
Installation,
cont’d
CAMBOARD Electronics
1
Turn all of the equipment off and, if applicable, disconnect
it from the power source.
As a stand-alone transmitter, the TP T 15HD 45 is compatible
with:
2
Connect the TP T 15HD 45 and its receiver to either end of
the UTP cable. See Cable testing and Skew delay problems in
this chapter.
• VTR001, VTR001 AAP, and VTR001 MAAP (RGBHV/RGBS
only)
For best results, use Extron UTP23SF cable available in
bulk or in various preterminated lengths. If necessary,
regular CAT 5, CAT 5e, and CAT 6 cable may be used.
3
Connect the external power supply to the TP T 15HD 45
and TP T A 45 (if installed). See Rear Panel Connectors in
this chapter.
4
If the TP T A 45 is being installed, connect the TP T A 45 to
the transmitter. See Rear Panel Connectors in this chapter.
5
Connect an output display device to the output connector
of the receiver.
6
Connect a computer to the 15-pin video input connector
of the transmitter.
7
Connect and power up all input and output devices, then
apply power to the TP T 15HD 45 power supply and test
for the display and/or audio outputs. If a problem is
encountered, check all connections before proceeding
further.
8
If the previous display and/or audio test was successful,
power off and disconnect all equipment, detach cables,
and install the TP T 15HD 45 and/or TP T A 45 modules.
See Mounting in this chapter.
Connect all device and power cables. Power up all input
and output devices, apply power to the transmitter and
receiver, and test for the display and/or audio.
There are two varieties of cable runs: simple runs, in which a
single cable is terminated only at the transmitter and receiver,
and complex runs, which can include patch bays and multiple
terminations and lengths of cable. In either case, the entire
cabling system should be tested.
Skew delay problems
As a pair, the TP T 15HD 45 and TP T A 45 are compatible with
the following Extron receivers and matrix switchers:
CAT 5 TP cable can lead to registration errors between the red,
green, and blue video signals. Pair skew can be measured with
test equipment or identified by viewing a crosshatch test pattern
with a critical eye to determine if either the red, green, or blue
video image leads (appears to the left of) the other two video
images. These images can be minimized or eliminated by one
of the following methods:
• TP R 15HD A
• TP R BNC A, TP R BNC AV
• TPX 88A
TP www.camboard.de
T 15HD 45 and TP T A 45 • Installation
To ensure proper cable termination, each transmission cable
system that uses CAT 5e or CAT 6 cable should be tested
(Extron UTP23SF cable does not need to be tested). Testing the
cable from the transmitter and receiver gives the most accurate
indications of cable problems.
The Microtest OMNI SCANNER 2 performs comprehensive
certification testing to the proposed CAT 6 standards. Other
manufacturers also make testing equipment. The tests include
advanced diagnostics for troubleshooting the cause and location
of many cable and termination problems. For simple
installation testing, the Microtest MICRO SCANNER PRO tests
wire map and cable length, including individual cable pair
length.
Compatibilty with other Extron products
2-6
Cable testing
A complete test measures cable length and tests the wire map,
attenuation, NEXT, PSNEXT, ELFEXT, PSELFEXT, return loss,
ACR and PSACR. All of these tests are critical for digital data
transfer. While all of these tests are important indicators of the
quality of the cable termination, the most critical testing
parameters for video transfer are wire map (T-568-A or T-568-B
termination) and pair length measurements. The largest
concern is equalization of skew between cable pairs. Cable
systems of 300 feet or less should exhibit no transmission
problems if they pass at least CAT 5e or preferably CAT 6-D5
channel certification testing.
If the transmitter or receiver is to be wall-mounted and
the power supply will be inaccessible, power must be
applied to the power supply before final mounting.
9
• TPX 88
Tel. 07131 911201
Fax 07131 911203
[email protected]
TP T 15HD
45 and TP T A 45 • Installation
2-7
im Vertrieb
von
Installation,
cont’d
CAMBOARD Electronics
•
Switch to Extron’s UTP23SF cable.
•
Add a skew compensation cable equal to the length of
pair skew to the receiver’s output.
•
Install an SEQ 100 15HD Skew Equalizer on the receiver’s
video output and adjust the skew for the leading video
image.
TP T 15HD 45 and TP T A 45
A
Mounting
The TP T 15HD 45 and TP T A 45 are designed to fit into a wallmountable or floor box-mountable 45 mm mounting frame.
COMPUTER
AUDIO
INPUT
INPUT
Appendix
The following application diagram illustrates one example of
installing these devices.
Projector
Mounting
Bracket
Mounting
Bolt
AV INPUT
Extron
TP R 15HD A
OUTPUT
RGB
Twisted Pair
Receiver
L
AUDIO
R
C
SYNC
SOG
C
VIDEO
N/C
POWER
15V
.34A MAX
CAT 5/6 or
Extron
Reference Information
Skew-Free TM
UTP Cable
Up to 500 feet
Ceiling
Specifications
Projector-mountable
Extron
TP T A 45
TP T 15HD 45
Parts Lists
IO
AUD
T
INPU
ER
PUT
COM
T
INPU
Twisted Pair
Transmitters
2-8
TP www.camboard.de
T 15HD 45 and TP T A 45 • Installation
Tel. 07131 911201
Fax 07131 911203
[email protected]
im Vertrieb
von cont’d
Reference
Information,
Reference
Information
CAMBOARD Electronics
Specifications
S/N ................................................
Crosstalk .......................................
Stereo channel separation ..........
CMRR ............................................
Video — video models
Number/signal type ................... 1 set of proprietary analog signals
Connectors
TP T 15HD 45 .................... (1) 8-pin spring force captive wire
connector
Audio input — audio models
Number/signal type
TP T A 45 ........................... 1 stereo, unbalanced
Connectors
TP T A 45 ........................... (1) 3.5 mm mini jack
Impedance
TP T A 45 ........................... >10k ohms, unbalanced, DC coupled
Nominal level ............................... -10 dBV (316mV)
Maximum level ............................ +5.5 dBu, (unbalanced) at 1%THD+N
Video input — video models
Number/signal type
TP T 15HD 45 .................... 1 analog RGBHV, RGBS, RGsB, component
video, or S-video; or
1 S-video and 1 NTSC/PAL/SECAM
composite video from a single source; or
3 NTSC/PAL composite video from a
single source
Connectors
TP T 15HD 45 .................... (1) 15-pin HD female (Mac and Sun/SGI to
VGA adapters are available)
Nominal level ............................... 1 V p-p for Y of component video and
S-video, and for composite video
0.7 V p-p for RGB
0.3 V p-p for R-Y and B-Y of component
video, and for C of S-video
Minimum/maximum levels ....... 0.3 V to 1.45 V p-p with no offset at unity
gain
Impedance .................................... 75 ohms
Horizontal frequency .................. 15 kHz to 130 kHz
Vertical frequency ....................... 30 Hz to 150 Hz
Return loss .................................... <-30 dB @ 5 MHz
DC offset (max. allowable) ......... 100 mV
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV
General
Audio — audio models
Number/signal type ................... 1 set of analog proprietary signals
Connectors
TP T A 45 ........................... (1) 2-pin direct insertion captive screw
connector
Frequency response .................... 20 Hz to 20 kHz, ±0.05 dB
THD + Noise ................................. 0.03% @ 1 kHz, 0.3% @ 20 kHz at nominal
level
TPwww.camboard.de
T 15HD 45 and TP T A 45 • Reference Information
2 dBu.
Audio output — refer to the TP Receivers Family
User’s Manual, part #68-547-02
Video output — refer to the TP Receivers Family
User’s Manual, part #68-547-02
A-2
>63 dB at maximum output (unweighted)
<-80 dB @ 1 kHz, fully loaded
>80 dB @ 1 kHz
>33 dB @ 20 Hz to 20 kHz
Tel. 07131 911201
Fax 07131 911203
Power
TP T 15HD 45 .................... 12 VDC, 1.0 A, external
TP T A 45 ........................... Shared with the TP T 15HD 45 transmitter
Temperature/humidity .............. Storage: -40 to +158°F (-40 to +70°C) /
10% to 90%, noncondensing
Operating: +32 to +122°F (0 to +50°C) /
10% to 90%, noncondensing
Rack mount .................................. No, but mountable in a 45 mm x 45 mm
opening
Enclosure type .............................. Metal
Enclosure dimensions
TP T 15HD 45, TP T A 45
Faceplate ................... 1.8" H x 1.7" W x 0.8" D (45 mm H x 45 mm
W x 20 mm D)
Device ........................ 1.1" H x 1.6" W x 1.2" D (29 mm H x 41 mm
W x 30 mm D)
(Depth excludes connectors.)
Product weight
All models ......................... 1.0 lbs (0.5 kg)
Shipping weight
All models ......................... 3 lbs (2 kg)
TP T 15HD 45 and [email protected]
T A 45 • Reference Information
A-3
im Vertrieb
von cont’d
Reference
Information,
Vibration ....................................... ISTA 1A in carton (International Safe
Transit Association)
Compliances ................................. CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF ............................................. 30,000 hours
Warranty ....................................... 3 years parts and labor
CAMBOARD Electronics
Parts Lists
Included parts
Description
All nominal levels are at ±10%.
Power supply: universal
12 VDC, 1.0 A
Specifications are subject to change without notice.
Part number
28-071-01 (TP T 15HD 45 only)
Tweeker (small screw driver)
TP T 15HD 45/TP T A 45
User’s Manual
Power supply - ships with
IEC power cord
70-055-01
Optional accessories
Description
A-4
TPwww.camboard.de
T 15HD 45 and TP T A 45 • Reference Information
Tel. 07131 911201A-5
Fax 07131 911203
Part number
VGA cable, 6', male-to-male
26-238-01
VGA with audio cable, 6', male-to-male
26-490-02
Enhanced Skew-Free™ A/V UTP cables
(assorted lengths)
26-569-xx
Plenum Enhanced Skew-Free™ A/V UTP
cables
26-570-xx
Enhanced Skew-Free™ A/V UTP bulk
cable, 1000'
22-141-03
Plenum Enhanced Skew-Free™ A/V UTP
bulk cable, 1000'
22-142-03
Plenum Enhanced Skew-Free™ A/V UTP
bulk cable, 1000 meters
22-141-04
TP T 15HD 45 and [email protected]
T A 45 • Reference Information
im Vertrieb
von cont’d
Reference
Information,
TPwww.camboard.de
T 15HD 45 and TP T A 45 • Reference Information
CAMBOARD Electronics
Tel. 07131 911201
Fax 07131 911203
[email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement