Daewoo | KOR-1A7G9T(AKM3180S) | Service manual | Daewoo KOR-1A7G9T(AKM3180S) Service manual

Daewoo KOR-1A7G9T(AKM3180S) Service manual
S/M No. : R1A7G 9T001
Service Manual
Microwave Oven
Model : KOR-1A7G
• Caution:
In this Manual, some parts can be changed for improving,
their performance without notice in the parts list. So, if you
need the latest parts information, please refer to PPL(Parts
Price List) in Service Information Center (http://svc.dwe.co.kr).
April 2006
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary: (1) Interlock operation, (2) Proper door closing, (3) Seal and
sealing surfaces (arcing, wear, and other damage), (4) Damage to or loosening of hinges and latches, (5)
Evidence of dropping or abuse.
(c) Before turning on power to the microwave oven for any service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation
and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual
before the oven is released to the owner.
(e) A microwave leakage check to verify compliance with the federal performance standard should be performed on each oven prior to release to the owner.
TABLE OF CONTENTS
SAFETY AND PRECAUTIONS ...........................................................................................................................................2
1. FOR SAFE OPERATION ..................................................................................................................................2
2. FOR SAFE SERVICE PROCEDURES .............................................................................................................2
SPECIFICATIONS ...............................................................................................................................................................3
EXTERNAL VIEW................................................................................................................................................................4
1. OUTER DIMENSION.........................................................................................................................................4
2. FEATURE DIAGRAM ........................................................................................................................................5
3. CONTROL PANEL ............................................................................................................................................6
INSTALLATION ...................................................................................................................................................................7
OPERATIONS AND FUNCTIONS.......................................................................................................................................8
DISASSEMBLY AND ASSEMBLY......................................................................................................................................9
INTERLOCK MECHANISM AND ADJUSTMENT.............................................................................................................16
TROUBLESHOOTING GUIDE ..........................................................................................................................................17
MEASUREMENT AND TEST ............................................................................................................................................21
1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT ........................................................................21
2. MICROWAVE RADIATION TEST ...................................................................................................................22
3. COMPONENT TEST PROCEDURE ...............................................................................................................23
WIRING DIAGRAM............................................................................................................................................................24
PRINTED CIRCUIT BOARD..............................................................................................................................................25
1. CIRCUIT CHECK PROCEDURE ....................................................................................................................25
2. PCB CIRCUIT DIAGRAM................................................................................................................................28
3. P.C.B. LOCATION NO ....................................................................................................................................29
EXPLODED VIEW AND PARTS LIST...............................................................................................................................30
1. DOOR ASSEMBLY .........................................................................................................................................30
2. CONTROL PANEL ASSEMBLY......................................................................................................................30
3. TOTAL ASSEMBLY.........................................................................................................................................30
1
SAFETY AND PRECAUTIONS
CAUTION
This device is to be Serviced only by Properly Qualified Service Personel. Consult the Service Manual for Proper
Service Procedures to Assure Continued Safety Operation and for Precautions to be Taken to Avoid Possible
Exposure to Excessive Microwave Energy.
1. FOR SAFE OPERATION
Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and may
cause serious bodily injury to the operator.
IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE.
(Only a competent service personnel should make repairs.)
(1) A broken door hinge.
(2) A broken door viewing screen.
(3) A broken front panel, oven cavity.
(4) A loosened door lock.
(5) A broken door lock.
The door gasket plate and oven cavity surface should be kept clean.
No grease, soil or spatter should be allowed to build up on these surfaces or inside the oven.
DO NOT ATTEMPT TO OPERATE THIS APPLIANCE WITH THE DOOR OPEN.
The microwave oven has concealed switches to make sure the power is turned off when the door is opened.
Do not attempt to defeat them.
DO NOT ATTEMPT TO SERVICE THIS APPLIANCE UNTIL YOU HAVE READ THIS SERVICE MANUAL.
2. FOR SAFE SERVICE PROCEDURES
1. If the oven is operative prior to servicing, a microwave emission check should be performed prior to servicing the
oven.
2. If any certified oven unit is found to have excessive emission level 5mw/cm2, the service person should:
(a) inform the manufacturer, importer or assembler,
(b) repair the unit at no cost to the owner,
(c) attempt to ascertain the cause of the excessive leakage,
(d) tell the owner of the unit not to use the unit until the oven has been brought into compliance.
3. If the oven operates with the door open, the service person should tell the user not to operate the oven and contact
the manufacturer and CDRH immediately.
CAUTION
MICROWAVE RADIATION
PERSONNEL SHOULD NOT BE EXPOSED TO THE MICROWAVE ENERGY WHICH MAY RADIATE FROM
THE MAGNETRON OR OTHER MICROWAVE GENERATING DEVICE IF IT IS IMPROPERLY USED OR
CONNECTED. ALL INPUT AND OUTPUT MICROWAVE CONNECTIONS. WAVEGUIDE FLANGES AND
GASKETS MUST BE SECURE. NEVER OPERATE THE DEVICE WITHOUT A MICROWAVE ENERGY
ABSORBING LOAD ATTACHED. NEVER LOOK INTO AN OPEN SAVEGUIDE OR ANTENNA WHILE THE
DEVICE IS ENERGIZED.
2
SPECIFICATIONS
MODEL
KOR-1A7G9T (AKM3180S)
POWER SUPPLY
110V-60Hz, SINGLE PHASE WITH EARTHING
MICROWAVE
POWER CONSUMPTION
1400W
GRILL
COMBINATION
MICROWAVE ENERGY OUTPUT
1000W
MICROWAVE FREQUENCY
OUTSIDE DIMENSIONS (W X H X D)
CAVITY DIMENSIONS (W X H X D)
2450MHz
539 x 300 x 431mm (21.2 x 11.8 x 16.1 in)
354 x 228 x 373 mm (13.9 x 9 x 14.7 in)
NET WEIGHT
APPROX. 15.8 kg (34.9 Ibs.)
TIMER
99 min. 99 sec.
FUNCTION SELECTIONS
MICROWAVE
POWER SELECTIONS
CAVITY VOLUME
* SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
EXTERNAL VIEW
1. OUTER DIMENSION
10 LEVELS
31 L
DIAGRAMA DE CARACTERISTICAS
1 2
9
3
8 7
1. Ganchos del seguro de la puerta - Este
horno funciona solamente cuando la puerta
está cerrada totalmente. Si se abre la puerta,
el horno deja de funcionar y de producir
microondas, hasta que la puerta se vuelve a
cerrar.
4
5
6
6. Plato de cristal - Fabricado con cristal
especial, resistente al calor. El plato siempre
debe colocarse en su eje antes del
funcionamiento. No cocine los alimentos
directamente sobre el plato.
7. Eje - En este eje debe ajustar el plato de cristal
para que pueda girar durante la cocción.
2. Sello de la puerta - Este sello mantiene a las
microondas dentro de la cavidad y asimismo
previene la fuga de éstas.
8. Anillo - Sostiene al plato de cristal para que
este pueda girar.
3. Cavidad del horno
9. Ventanilla de puerta - permite observar los
alimentos. Esta ventanilla ha sido diseñada
para permitir la vista al interior de la cavidad y
al mismo tiempo impedir la salida de las
microondas.
4. Cubierta protectora - Evita que la salida de
las microondas se salpique cuando los
alimentos se cocinan.
5. Sistema de sujeción con seguro - Previene
que el horno funcione mientras la puerta se
encuentra abierta.
5
DIAGRAMA DE CARACTERISTICAS (CONTINUACIÓN)
0
q
w
e
r
y
t
i
u
o
p
a
16. Power (Potencia) - Usado para ajustar el
nivel de potencia.
10. Display (Pantalla) - Muestra el tiempo de
cocción, indicador de nivel de potencia y
tiempo actual.
17. Kitchen Timer (Tiempo de cocinado) Usado en minutos y puede retrasar el tiempo
programado después de cocinar.
11. One touche (Un toque) - Usado para
calentar o recalentar cantidades específicas
de comida.
18. Defrost (Descong) - Usado para
descongelar comida.
12. More (Mas) - Usado para agregar tiempo de
cocción.
19. Clock (Reloj) - Usado para ajustar el reloj.
13. Less (Menos) - Usado para quitar el tiempo
de cocción.
20. Stop/Clear (Paro/Limpiar) - Usado para
detener la operación del horno o borrar datos
de cocción.
14. Auto Defrost (A: Descong) - Usado para
descongelar comida (por peso).
21. Start/Speedy cook (Inicio/Cocción rápida Usado para iniciar el horno y puede utilizarlo
para ajustar el tiempo de de recalentado.
15. Time set pad (Botones de ajuste de
tiempo) - Usado para ajustar el tiempo de
cocción y el tiempo actual.
6
INSTALLATION
1. Steady, flat location.
This microwave oven should be set on a steady, flat surface.
2. Leave space behind and side.
All air vents should be kept a clearance. If all vents are covered during operation, the oven may be overheated
and, eventually, cause oven failure.
3. Away from radio, and TV sets
Poor television reception and radio interference may result if the oven is located close to a TV, radio, antenna, or
feeder and so on.
4. Away from heating appliances and water taps
Keep the oven away from hot air, steam or splash when choosing a place to position it, or the insulation might be
adversely affected and breakdowns occur.
5. Power supply
• Check your local power source.
This microwave oven requires a current of approximately 20 amperes, 110Volts, 60Hz grounded outlet.
• Power supply cord is about 1.0 meters long.
1. A short power-supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over
a longer cord.
2. Longer cord sets or extension cords are available and may be used if care is exercised in their use.
3. If a long cord or extension cord is used:
1) The marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance.
2) The extension cord must be a grounding type 3-wire cord.
3) The longer cord should be arranged so that it will not drape over the counter top or tabletop where it can be
pulled on by children or tripped over unintentionally.
6. Examine the oven after unpacking for any damage such as:
A misaligned door, broken door or a dent in cavity.
If any of the above are visible, DO NOT INSTALL, and notify dealer immediately.
7
OPERATIONS AND FUNCTIONS
1. Connect the mains lead to an electrical outlet.
2. After placing the food in a suitable container, open the oven door and put it on the glass tray. The glass tray must always
be in place during cooking.
3. Close the door securely.
4. When the oven door is opened, the light turns on.
5. The oven door can be opened at any time during operation by pushing the door release button on the control panel.
The oven will automatically shut off. To restart the oven, close the door and then touch START pad.
6. Each time a pad is touched. a BEEP will sound to acknowledge the touch.
7. The oven automatically cook on full power unless set to a lower power level.
8. The display will show : 0 when the oven is plugged in.
9. Time clock returns to the present time when the cooking time ends.
10. When the STOP/CLEAR pad is touched during the oven operation, the oven stops cooking and all information retained.
To erase all information (except the present time), touch the STOP/CLEAR pad once more. If the oven door is opened
during the oven operation, all information is retained.
11. If the START pad is touched and the oven does not operate, check the area between the door and door is closed
securely. The oven will not start cooking under the door is completely closed or the program has been reset.
Make sure the oven is properly installed and plugged into the electrical.
Wattage output chart
The power level is set by touching the POWER pad. The chart shows the display, the power level and the percentage
of power.
Touch POWER Pad
Power Level(Display)
Approximate Percentage of Power
Once
P-HI
100%
Twice
P-90
90%
3 times
P-80
80%
4 times
P-70
70%
5 times
P-60
60%
6 times
P-50
50%
7 times
P-40
40%
8 times
P-30
30%
9 times
P-20
20%
10 times
P-10
10%
11 times
P-00
00%
8
DISASSEMBLY AND ASSEMBLY
Cautions to be observed when troubleshooting.
Unlike many other appliances, the microwave oven is high-voltage, high-current equipment.
It is completely safe during normal operation.
However, carelessness in servicing the oven can result in an electric shock or possible danger from a short circuit.
You are asked to observe the following precautions carefully.
1. Always remove the power plug from the outlet before servicing.
2. Use an insulated screwdriver and ware rubber gloves when servicing the high voltage side.
3. Discharge the high voltage capacitor before touching any oven components or wiring.
(1) Check the grounding.
Do not operate on a two-wire extension cord.
The microwave oven is designed to be used while earthed.
It is imperative, therefore, to make sure it is earthed
properly before beginning repair work.
(2) Warning about the electric charge in the high voltage capacitor.
For about 30 seconds after the operation stopped and electric
charge remains in the high voltage capacitor.
When replacing or checking parts, short between oven chassis and
the negative high terminal of the high voltage capacitor by using a
properly insulated screwdriver to discharge.
4. When the 20A fuse is blown out due to the operation of the monitor
switch; replace primary interlock switch, secondary interlock switch and
interlock monitor switch.
5. After repair or replacement of parts, make sure that the screws are
properly tightened, and all electrical connections are tightened.
6. Do not operate without cabinet.
SHORT
CAUTION : Service personnel should remove their watches whenever working close to or replacing the magnetron.
WARNING : When servicing the appliance, need a care of touching or replacing high potential parts because of
electrical shock or exposing microwave. These parts are as follows - HV Transformer, Magnetron,
HV Capacitor, HV Diode, HV fuse.
9
1. To remove cabinet
1) Remove three screws on cabinet back.
2) Pull the cabinet backward.
2. To remove door assembly
1) Remove two screw which secure the stopper hinge top.
2) Remove the door assembly from top plate of cavity.
3) Reverse the above for reassembly.
NOTE : After replacing the door assembly, perform a check of correct alignment with the hinge and cavity front plate.
10
3. To remove door parts.
REF NO.
PART CODE
PART NAME
DESCRIPTION
A01
3511604730
DECORATOR DOOR *U
SUS430 T0.5 H/L
1
A02
3511604720
DECORATOR DOOR *T
SUS430 T0.5 H/L
1
A03
3511609510
DECORATOR DOOR *L
SUS430 T0.5 H/L
1
A04
3512204370
FRAME DOOR
ABS XR-401 SR-0320G
1
A05
3517005930
BARRIER-SCREEN *O
TEMP GLASS T3.2, NO PRINT
1
A06
3515202900
STOPPER HINGE *T AS
KOR-121M0A
1
A07
3511711300
DOOR PAINTING AS
KOR-1A1G0A
1
A08
3517005800
BARRIER-SCREEN *I
PETP T0.1
1
A09
3512301900
GASKET DOOR
PP 5113MF6
1
A10
3513100730
HOOK
POM BLACK
1
A11
3515101900
SPRING HOOK
PW-1
1
A12
7122401211
SCREW TAPPING
T2S TRS 4X12 MFZN
1
A13
3511609310
DECORATOR DOOR *R
SUS430 T0.5 H/L
1
A14
3512602700
HANDLE DOOR *U
ABS XR-401 H-2938
1
A15
3512602600
HANDLE DOOR *T
SUS304 T0.6 HAIR LINE
1
(1) Remove the gasket door from door painting as.
(2) Remove the barrier screen inner from door painting as.
(3) Remove the frame door from door painting as.
(4) Remove the stopper hinge top form door painting as.
(5) Remove the spring and the hook door painting as.
(7) Remove two screws holding the handle.
(8) Remove the handle from frame door.
(9) Reverse the above steps for reassembly.
11
Q’TY
REMARK
5. To remove control panel parts.
REF NO.
PART CODE
PART NAME
DESCRIPTION
Q’TY
B01
3511604850
DECORATOR C-PANEL
SUS430 T0.5 H/L
1
B02
3518571900
SWITCH MEMBRANE
KOR-1A7G9T
1
B03
3516727510
CONTROL-PANEL
ABS SG-175 SG-0760D
1
B04
PKMPMSFK40
PCB MAIN MANUAL AS
1A(1000W,T,9,99)
1
B05
7122401211
SCREW TAPPING
T2S TRS 4X12 MFZN
4
REMARK
(1) Remove a screw which secure the control panel, push up two snap fits and draw forward the control panel assembly.
(2) Remove four screws which secure the PCB assembly to control panel.
(3) Disconnect membrane tail from the connector of the PCB assembly.
(4) Detach membrane from the control panel.
(5) Reverse the above steps for reassembly.
13
4. Method to reduce the gap between the door seal and the oven front surface.
(1) To reduce gap located on part ‘A’
• Loosen two screws on stopper hinge top, and then
push the door to contact the door seal to oven front
surface.
• Tighten two screws.
(2) To reduce gap located on part ‘B’
• Loosen two screws on stopper hinge under, and then
push the door to contact the door seal to oven front
surface.
• Tighten two screws.
(3) To reduce gap located on part ‘C’
• Loosen a screw on interlock switch assembly located
top of oven body.
• Draw the interlock switch assembly inward as possible
to engage with hook on the door bottom.
• Tighten a screw.
(4) To reduce gap located on part ‘D’
• Loosen a screw on interlock switch assembly located bottom of oven body.
and (4) are same as step (3).
NOTE : A small gap may be acceptable if the microwave leakage does not exceed 4mW/cm2.
12
6. To remove high voltage capacitor.
1) Remove a screw which secure the grounding ring
terminal of the H.V. diode and the capacitor holder.
2) Remove the H.V. diode from the capacitor holder.
3) Reverse the above steps for reassembly.
◆ High voltage circuit wiring
7. To remove magnetron.
1) Remove a screw which secure the magnetron.
2) Remove the magnetron.
3) Reverse the above steps for reassembly.
NOTE : Never install the magnetron without the metallic gasket plate which is packed with each magnetron to prevent microwave leakage. Whenever repair work is carried out on magnetron, check the microwave leakage. It shall
not exceed 4mW/cm2 for a fully assembled oven with door normally closed.
Magnetron antenna
Metallic
gasket
plate
Cooling fin
Filament
terminal
<MAGNETRON>
14
8. To remove wind guide assembly.
1) Remove a screw for earthing.
2) Remove the noise filter from the wind guide.
3) Remove a screw which secure the wind guide assembly.
4) Draw forward the wind guide assembly.
5) Pull the fan from the motor shaft.
6) Remove two screws which secure the motor shaded pole.
7) Remove the motor shaded pole.
8) Reverse the above steps for reassembly.
9. To remove H.V.transformer.
1) Remove four screws holding the H.V.transformer.
2) Remove the H.V.transformer.
3) Reverse the above steps for reassembly.
15
INTERLOCK MECHANISM AND ADJUSTMENT
The door lock mechanism is a device which has been specially designed to completely eliminate microwave radiation when
the door is opened during operation, and thus to perfectly prevent the danger resulting from the leakage of microwave.
(1) Primary interlock switch
When the door is closed, the hook locks the oven door. If the door is not closed properly, the oven will not operate.
When the door is closed, the hook pushes the button of the microswitch. Then the button of the primary interlock switch
bring it under NO condition.
(2) Secondary interlock switch and interlock monitor switch
When the door is closed, the hook pushes the lock lever downward. The lock lever presses the button of the interlock
monitor switch to bring it under NO condition and presses the button of the secondary interlock switch to bring it under
NO condition.
ADJUSTMENT :
Interlock monitor switch
When the door is closed, the interlock monitor switch should be changed (NO condition) before other switches are closed.
When the door is opened, the interlock monitor switch should be changed (NC condition) after other switches are opened.
(3) Adjustment steps
a) Loosen the mounting screw.
b) Adjust interlock switch assembly position.
c) Make sure that lock lever moves smoothly after adjustment is completed.
d) Tighten completely a mounting screw.
NOTE :
Microwave emission test should be performed after adjusting interlock mechanism. If the microwave emission exceed
4mW/cm2, readjust interlock mechanism.
16
TROUBLESHOOTING GUIDE
Following the procedure below to check if the oven is defective or not.
1. Check grounding before trouble checking.
2. Be careful of the high voltage circuit.
3. Discharge the high voltage capacitor.
4. When checking the continuity of the switches, fuse or high voltage transformer, disconnect one lead wire from these parts
and check continuity with the AC plug removed. To do otherwise may result in a false reading or damage to your meter.
NOTE : When electric parts are checked, be sure the power cord is not inserted the wall outlet.
Check wire harness, wiring and connected of the terminals and power cord before check the parts listed
below.
(TROUBLE 1) Oven does not operate at all ; any inputs can not be accepted.
CONDITION
CHECK
RESULT
Check continuity of interlock
monitor switch with door closed
Continuity
Fuse blows.
CAUSE
Malfunction of
interlock monitor switch
REMEDY
Replace
No Continuity
Replace fuse
Check continuity of of primary
interlock switch contact with door
partially open until interlock monitor switch contact close
Continuity
Shorted contacts of primary
interlock switch.
Replace
No Continuity
Check continuity of primary
winding of low voltage transformer
0Ω or infinite
Approx.
150~310
(normal)
Normal
Disconnect one side of the lead
wire connected form high voltage transformer to the high voltage capacitor and operate the
unit
Fuse again
blows
17
Defective low
voltage transformer
Defective high
voltage capacitor
Defective high
voltage transformer
Replace
Replace
Replace
CONDITION
Outlet has
proper voltage Fuse
does not
blow.
CHECK
RESULT
CAUSE
REMEDY
No
Continuity
Defective magnetron
Replace
Check continuity of magnetron
Check continuity of
power supply cord
No
Continuity
Open power supply cord
Replace
Normal
Defective touch
control circuit
Replace
Malfunction of secondary interlock
switch
Replace
Display do not shown
countdown
NOTE
All these switches must be replaced at the same time, please refer to “Interlock Mechanism And Adjustment”.
(TROUBLE 2) Display shows all figures selected, but oven does not start cooking, even though desired program and
time are set and start button is tapped.
CONDITION
CHECK
RESULT
CAUSE
REMEDY
Turn table
motor and
oven lamp
do not turn
on
Check continuity of primary interlock switch
No
Continuity
Malfunction of primary interlock
switch
Adjust or
replace
Check continuity of secondary
interlock switch
No
Continuity
Check D.C. voltage being supplied to RELAY (RY2) coil
0V
Defective touch
control circuit
Approx.
15 VDC
Faulty contacts of
RELAY (RY2) or
open relay coil
18
Malfunction of secondary interlock
switch
Adjust or
replace
Replace
Replace
(TROUBLE 3)
CONDITION
No
microwave
oscillation
No microwave oscillation even though fan motor rotates.
CHECK
RESULT
CAUSE
REMEDY
Check continuity of high
voltage capacitor terminals
with wires removed
Continuity
Defective high
voltage transformer
Replace
Check continuity of high voltage
rectifier in forward and backward
direction with DC megger
Continuity in
backward
direction
Defective high
voltage rectifier
Replace
Connect megger leads to magnetron terminal and magnetron
body
Continuity
Defective magnetron
Replace
Defective high
voltage transformer
Replace
0 Ω or ∞
Check resistance of primary and
secondary coil of high voltage
transformer
No
Continuity
Check continuity of magnetron
with wires removed
No
Continuity
Check continuity of filament terminal of high voltage transformer
Defective magnetron
Defective high
voltage transformer
0V
Check D.C. voltage being supplied to RELAY (RY1) coil
Defective touch
control circuit
Approx
15 VDC
19
Faulty
contacts or
RELAY (RY1)
or open
relay coil
Replace
Replace
Replace
Replace
(TROUBLE 4)
The following visual conditions indicate a probable defective touch control circuit or membrane switch
assembly.
1. Incomplete segments
(1) Segments missing
(2) Partical segments missing
(3) Digit flickering other than normal display slight flickering
(4) “ :0” does not display when power is on.
2. A distinct change in the display is not on when they numbers in the
display.
3. One or more digits in the display are not on when they should be.
4. Display indicates a number different from one touched.
5. Specific numbers (for example 2 or 3) will not display when the panel is touched.
6. Display does not count down or up with time cooking or clock operation.
7. Oven is programable and cooks normally but no display shows.
8. Display obviously jumps in time while counting down.
9. Display counts down noticeably too fast while cooking.
10. Display does not show the time of day when the STOP/CLEAR pad is touched.
11. Oven lamp and turntable motor do not stop although cooking is finished. Check if the RELAY 2 contacts close if they are
close, replace touch control circuit.
CONDITION
CHECK
Display does
not show
programming
at all, even if
keyboard is
touched.
Check each pad for
continuity of the membrane
keyboard for the following keyboard check procedure
RESULT
CAUSE
Normal
Malfunction
of control circuit
board
Abnormal
Malfunction
of the membrane
keyboard
REMEDY
Replace
control circuit
board
Replace the
membrane
keyboard
NOTE
Before following the particular steps listed above in the troubleshooting guide for the membrane keyboard's, failure, please check for the continuity of each wire-harness between the membrane keyboard
and P.C.B. assembly.
20
MEASUREMENT AND TEST
1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT
Microwave output power can be checked by indirectly measuring the temperature rise of a certain amount of water
exposed to the microwave as directed below.
PROCEDURE
1. Microwave power output measurement is made with the microwave oven
supplied at rated voltage and operated at its maximum microwave power
setting with a load of 1000±5cc of potable water.
2. The water is contained in a cylindrical borosilicate glass vessel having a
maximum material thickness of 3 mm and an outside diameter of approximately 190 mm.
3. The oven and the empty vessel are at ambient temperature prior to the
start of the test.
The initial temperature of the water is 10±2˚C (50±3.6˚F)
It is measured immediately before the water is added to the vessel.
After addition of the water to the vessel, the load is immediately placed on
the center of the shelf, which is in the lowest normal position.
4. Microwave power is switched on.
5. Heating time should be exactly A seconds. (Refer to table as following)
Heating time is measured while the microwave generator is operating at full power.
The filament heat-up time for magnetron is not included.
6. The initial and final temperature of water is selected so that the maximum difference between the ambient and final
water temperature is 5K.
7. The microwave power output P in watts is calculated from the following formula :
P=4187 X ▲T/t
• ▲T is difference between initial and ending temperature.
• t is the heating time.
The power measured should be B (Refer to SPECIFICATIONS)W±10.0%.
CAUTION :
1. Water load should be measured exactly to 1 liter.
2. Input power voltage should be exactly specified voltage(Refer to SPECIFICATIONS).
3. Ambient temperature should be 20±2˚C(68±3.6˚F)
Heating time for power output:
A(second)
70
64
60
56
52
49
47
44
42
40
38
B(W)
600
650
700
750
800
850
900
950
1000
1050
1100
21
2. MICROWAVE RADIATION TEST
CAUTION :
1. Make sure to check the microwave leakage before and after repair of adjustment.
2. Always start measuring of an unknown field to assure safety for operating personnel from microwave energy.
3. Do not place your hands into any suspected microwave radiation field unless the safe density level is known.
4. Care should be taken not to place the eyes in direct line with the source of microwave energy.
5. Slowly approach the unit under test until the radiometer reads an appreciable microwave leakage from the unit
under the test.
PROCEDURES
1. Prepare Microwave Energy Survey Meter, 600cc glass
beaker, and glass thermometer 100˚C(212˚F).
2. Pour 275cc±15cc of tap water initially at 20±5˚C(68±9˚F) in
the 600cc glass beaker with an inside diameter of approx.
95mm(3.5in.).
3. Place it at the center of the tray and set it in a cavity.
4. Close the door and operate the oven.
5. Measure the leakage by using Microwave Energy Survey
Meter with dual ranges, set to 2450MHz.
1) Measured radiation leakage must not exceed the value
prescribed below. Leakage for a fully assembled oven with
door normally closed must be less than 4mW/cm2.
2) When measuring the leakage, always use the 5cm(2in.)
space cone with probe. Hold the probe perpendicular to
the cabinet and door. Place the space cone of the probe
on the door, cabinet, door seem, door viewing screen, the
exhaust air vents and the suction air vents.
3) Measuring should be in a counter-clockwise direction at a
rate of 1 in./sec. If the leakage of the cabinet door is
unknown, move the probe more slowly.
4) When measuring near a corner of the door, keep the probe
perpendicular to the areas making sure the probe end at
the base of the cone does not get closer than 2 in. from
any metal. If it does not, erroneous reading may result.
22
3. COMPONENT TEST PROCEDURE
• High voltage is present at the high voltage terminal of the high voltage transformer during any cooking cycle.
• It is neither necessary nor advisable to attempt measurement of the high voltage.
• Before touching any oven components or wiring, always unplug the oven from its power source and discharge the
capacitor.
1. High voltage transformer
(1) Remove connections from the transformer terminals and check continuity.
(2) Normal readings should be as follows:
Secondary winding
Approx. 140Ω±10%
Filament winding
Approx. 0Ω
Primary winding
Approx. 1Ω
2. High voltage capacitor
(1) Check continuity of capacitor with meter on the highest OHM scale.
(2) A normal capacitor will show continuity for a short time, and then indicate 10MΩ once the capacitor is charged.
(3) A shorted capacitor will show continuous continuity.
(4) An open capacitor will show constant 10MΩ.
(5) Resistance between each terminal and chassis should be infinite.
3. High voltage diode
(1) Isolate the diode from the circuit by disconnecting the leads.
(2) With the ohmmeter set on the highest resistance scale measure the resistance across the diode terminals.
Reverse the meter leads and again observe the resistance reading.
Meter with 6V, 9V or higher voltage batteries should be used to check the front-back resistance of the diode,
otherwise an infinite resistance may be read A normal diode’s resistance will be infinite in one direction and
several hundred KΩ in the other direction.
4. Magnetron
For complete magnetron diagnosis, refer to “Measurement of the Microwave Power Output”.
Continuity checks can only indicate and open filament or a shorted magnetron.
To diagnose for an open filament or a shorted magnetron.
(1) Isolate magnetron from the circuit by disconnecting the leads.
(2) A continuity check across magnetron filament terminals should indicate 0.1Ω or less.
(3) A continuity check between each filament terminal and magnetron case should read open.
5. Fuse
If the fuse in the primary and monitor switch circuit is blown when the door is opened, check the primary and monitor
switch before replacing the blown fuse.
In case the fuse is blown by an improper switch operation, replace the defective switch and fuse at the same time.
Replace just the fuse if the switches operate normally.
6. Interlock switches
(1) You can test continuity of safety interlock and monitor switch by using ohmmeter.
(2) The switch peration is checked by zero/unlimited.
The meter should indicate zero resistance.
(3) The sequence of check is interlock monitor switch, primary and secondary interlock switches check.
23
WIRING DIAGRAM
24
PRINTED CIRCUIT BOARD
1. CIRCUIT CHECK PROCEDURE
1. Low Voltage Transformer check
The low voltage transformer is located on the P.C.B.
Measuring condition: input voltage : 110V/Frequency : 60Hz
Terminal Voltage
5-6-7
LOAD
AC 12.6 V
NO LOAD
AC 14.7 V
NOTE :
1. Refer to Circuit Diagram (point 4).
2. Secondary side voltage of the low voltage transformer changes in proportion to fluctuation of power source voltage.
3. The allowable tolerance of the secondary voltage is within 5% of nominal voltage.
2. Voltage check
Key check point
NO
CHECK POINT
1
IC 1 PIN 5
2
IC 1 PIN 8
REMARK
5 VDC
T:16.67ms(60Hz)
3
IC 1 PIN 35 OR PIN 36
T:250ns(4MHz)
Check method
NO
MEASURE POINT
1
MP1
2
MP2
WAVE FORM
REMEDY
REMARK
DC 5V 0.25V
Replace VL1, EC1
NO LOAD
DC 12V 2.0V
Replace EC2, D11, D13, D14
NO LOAD
NOTE :
Each measure point must be measured with GND point.
25
3. When there is no microwave oscillation
1) When touching START pad, oven lamp does not turn on.
Fan motor does not rotate, but cook indicator in display comes on.
B
A
RY2
42
D10
(TRAY
LAMP)
Q10
RY2
- Check method
POINT
A
B
RELAY 2 ON
5VDC
GND
RELAY 2 OFF
GND
12VDC
STATE
2) When touching START pad, oven lamp turns on.
Fan motor and turntable rotate and cook indicator in display comes on.
B
A
RY1
41
D8
(M/W)
Q9
RY1
- Check method
POINT
A
B
RELAY 1 ON
5VDC
GND
RELAY 1 OFF
GND
12VDC
STATE
4. When the door is opened during operation, the count down timer does not stop.
A
B
R1
CN1
1
2
27
R10
C1
R9
D.O.M SW
C2
+5V
-Check method
POINT
A
B
1) DOOR OPEN
OPEN
5VDC
2) DOOR CLOSED
CLOSE
GND
STATE
CHECK NO
1
METHOD
REMEDY
Check the stage (ON, OFF) of the door open monitor switch by
resistance measurement.
5. When the digital clock does not operate properly.
Refer to Circuit Diagram.
POINT
WAVE FORM
IC 1 PIN 8
T:16.67ms(60Hz)
* If clock does not keep exact time, you must check resistor R20 and zener diode ZD2.
27
Replace door open monitor
switch.
2. PCB CIRCUIT DIAGRAM
28
3. PCB LOCATION NO.
NO
NAME
SYMBOL
SPECIFICATION
PART CODE
Q’TY
1
BUZZER
BZ1
BM-20K
3515600100
1
2
C ARRAY
CA1
7P(6) 1000PF M 50V
CN6XB-102M
1
3
CAPACITOR ELEC
EC1
50V RS 10UF
CEXE1H100A
1
4
CAPACITOR ELEC
EC2
25V RSS 1000MF
CEXF1E102V
1
5
CONNECTOR WAFER
CN1
YW396-02V
3519150520
1
6
CONNECTOR WAFER
CN2
FCZ 254-11
441M367160
1
7
CONNECTOR WAFER
CN3
YW396-05AV
3519150510
1
8
DIODE RECTIFY
D1~5, D8~D12
1N4148
DZN4148---
10
9
DIODE RECTIFY
D13,14
KN4004A
DZN4004A--
2
10
DIODE ZENER
ZD1
UZ- 3.3BSB 1/2W
DZUZ3R3BSB
1
11
DIODE ZENER
ZD2
UZ- 5.1BSB 1/2W
DZUZ5R1BSB
1
12
LED DISPLAY
DP1
ELF-496GWB
DDDG631H--
1
13
PCB MAIN
M158-1
81.5X139.9
3514315411
1
14
R ARRAY
RA2
8P(7) 1/8 100K OHM J
RA-88X104J
1
15
R ARRAY
RA1
7P(6) 1/8 100K OHM J
RA-87X104J
1
16
RESISTOR
R2~8
1/6W 330 5%
RD-AZ331J-
7
17
RESISTOR
R1,10,12,17,18,22
1/6W 1K 5%
RD-AZ102J-
6
18
RESISTOR
R9
1/6W 100K 5%
RD-AZ104J-
1
19
RESISTOR
R11
1/6W 200 5%
RD-AZ201J-
1
20
RESISTOR
R13,R19,R20
1/6W 10K 5%
RD-AZ103J-
3
21
RESISTOR
R14
1/6W 1M 5%
RD-AZ105J-
1
22
RESISTOR
R21
1/4W 51 5%
RD-4Z510J-
1
23
RESONATOR CERA
CR1
CRT 4.00MS
5P4R00MTS-
1
24
IC REGULATOR
VL1
MC7805C
1CPMC7805C
1
25
TRANSISTOR
Q1~5
KRA106M
TZRA106M--
5
26
TRANSISTOR
Q9~11
KRC106M
TZRC106M--
3
27
TRANSISTOR
Q6
KTA-1266Y
TZTA1266Y-
1
28
CAPACITOR CERA
C5
102 50V Z AXIAL
CCZB1H102K
1
29
CAPACITOR CERA
C1~4,C6~7
104 50V Z AXIAL
CCZF1H104Z
6
30
TRANS POWER
LVT1
DMR-631FS
5EPU035302
1
31
WIRE COPPER
J1~J10,J13,J14
1/0.52 TIN COATING
85801052GY
12
32
WIRE COPPER
J11,J12
1/0.52 TIN COATING
85801053GY
2
33
SW RELAY
RY2
CS11-12SH 1C 1P
5SC0101128
1
34
IC MICOM
IC1
HMS81C1708B-HN017
150SR6N6Q-
1
35
WIRE COPPER
SJ1,SJ3,SJ7
1/0.52 TIN COATING
85801052GY
1
36
SW RELAY
RY1
G5G-1A DC12V
5SC0101121
1
29
EXPLODED VIEW AND PARTS LIST
1. DOOR ASSEMBLY
Refer to Disassembly and assembly.
2. CONTROL PANEL ASSEMBLY
Refer to Disassembly and assembly.
3. TOTAL ASSEMBLY
30
✔ Caution : In this Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you
need the latest parts information, please refer to PPL(Parts Price List) in Service Information Center .
NO
A00
B00
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F29
F30
F31
F32
F33
F34
F35
F36
F37
F38
F39
F40
F41
F42
F43
F44
F45
F46
F47
F48
PART CODE
3511711270
PKCPSWA820
3510805500
7112401011
3516110400
7122401211
7122401211
7272400811
35113PANOA
7112401011
7121300611
3518902600
7272400811
3518606600
7121402511
3963822730
3512517000
3511800300
3518002900
3516004000
7122400811
3513003200
3518302201
3518400900
5F1C020315
3518113840
3516003700
3510312400
7112401011
3512100900
7272400811
3515202800
3512718080
4415A17352
4415A66910
3518571000
3513702610
3513811710
4415A66910
3513601500
7121400611
3966820200
3518905400
3513003410
7272400811
3511406200
3517400620
3514701501
3512519300
441X335A10
PART NAME
DOOR AS
CONTROL-PANEL AS
CABINET AS
SCREW TAPPING
CAVITY AS
SCREW TAPPING
SCREW TAPPING
SCREW TAPTITE
CORD POWER AS
SCREW TAPPING
SCREW TAPPING
THERMOSTAT
SCREW TAPTITE
NOISE-FILTER
SCREW TAPPING
MOTOR SHADED POLE
GUIDE WIND
FAN
MAGNETRON
SPECIAL SCREW
SCREW TAPPING
HOLDER HV CAPACITOR
CAPACITOR HV
DIODE HV
FUSE
TRANS HV
SPECIAL SCREW
BASE
SCREW TAPPING
FOOT
SCREW TAPTITE
STOPPER HINGE *U AS
HARNESS MAIN
SW MICRO
SW MICRO
SWITCH PUSH
LEVER LOCK
LOCK
SW MICRO
LAMP
SCREW TAPPING
MOTOR SYNCRO
THERMOSTAT
HOLDER THERMOSTAT
SCREW TAPTITE
COVER WAVE GUIDE
COUPLER
ROLLER
GUIDE ROLLER
TRAY
DESCRIPTION
KOR-1A7G9S
KOR-1A7G9T
KOR-1A1G0A LOUVER
T1 TRS 4 X10 MFZN
KOR-1A1G0A
T2S TRS 4X12 MFZN
T2S TRS 4X12 MFZN
TT3 TRS 4X8 MFZN
3X2.0 120X120 120-RTML
T1 TRS 4 X10 MFZN
T2S PAN 3X6 MFZN
OFF:90 ON:60 H #187
TT3 TRS 4X8 MFZN
DWLF-M17
T2S PAN 4X25 MFZN
110V 60HZ MW10KA-M01
PP
PP+30%GLASS
2M218J(F)P 6CF
T2 BOLT FLANGE 5X12 DACRO
T2S TRS 4*8 MFZN
SECC T0.6
2100VAC 0.98UF #187 75MM
HVR-1X-3AB 12KV #187
65TS 125V 20A
DW-R11AT-1BT
TT3 HEX 4X8 FLG MFZN
SBHG T0.7
T1 TRS 4 X10 MFZN
PP DASF-130
TT3 TRS 4X8 MFZN
KOR-121M0A
KOR-1A7G9T
VP-533A-OF SPNO #187 200G
VP-531A-OF/SZM-V16-FA-61
MP101C
POM
POM BLACK
VP-531A-OF/SZM-V16-FA-61
BL 125V 25W T25 C5A H187
T2S PAN 4X6 MFZN
120V 2W GM-16-12F17
OFF:90 ON:60 H #187 NB
PP(BK)
TT3 TRS 4X8 MFZN
HEATPROOF PP
XAREC
TEFLON D:14.5
PP 5113MF6 A353B
BORO-S1 GLASS(NEG)
31
Q'TY
1
1
1
3
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
4
1
5
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
DAEWOO ELECTRONICS CORP.
686, AHYEON-DONG MAPO-GU SEOUL, KOREA
C.P.O. BOX 8003 SEOUL, KOREA
TELEX: DWELEC K28177-8
CABLE: “DAEWOOELEC”
S/M NO. :R1A7G 9T001
PRINTED DATE: April. 2005
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising