Crestron WMKT-1000L Manual

Crestron WMKT-1000L Manual
Crestron TMK-1000L & WMKT-1000L
Trim Ring Mount Kits
Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2008 Crestron Electronics, Inc.
Crestron TMK-1000L & WMKT-1000L
Trim Ring Mount Kits
Contents
Trim Ring Mount Kits: TMK-1000L & WMKT-1000L
1
Description................................................................................................................................. 1
Setup .......................................................................................................................................... 2
Supplied Hardware ...................................................................................................... 2
Installation ................................................................................................................... 4
Resources................................................................................................................................. 10
Industry Compliance ................................................................................................. 10
Reference Documents................................................................................................ 10
Further Inquiries ........................................................................................................ 10
Future Updates .......................................................................................................... 10
Return and Warranty Policies .................................................................................................. 11
Merchandise Returns / Repair Service ...................................................................... 11
CRESTRON Limited Warranty................................................................................. 11
Installation Guide – DOC. 6063A
Contents • i
Crestron TMK-1000L & WMKT-1000L
Trim Ring Mount Kits
Trim Ring Mount Kits:
TMK-1000L & WMKT-1000L
Description
Trim Ring Mount Kits are the preferred method of mounting the Crestron® APAD
LCD controller when a finished appearance within a neatly trimmed cutout is
required. This application is perfect for wallpapering.
NOTE: If mounting into a material other than drywall (for example, wood lectern,
concrete, or rock) use the cutout template, available in the post-construction kit
WMKT-1000L. For concrete and rock mounting material, allow for proper
ventilation before mounting the controller.
There are two Trim Ring Mount Kits. The TMK-1000L is a pre-construction
accessory. Pre-construction refers to framed walls prior to hanging drywall. This
accessory must be used with either the Pre-Construction Mount Kit (PMK-1000L) or
Back Box (BB-1000L).
The WMKT-1000L is a post-construction kit. Post-construction refers to framed
walls with drywall hung. This accessory is designed with a mounting plate so that it
can be placed anywhere on a wall without the support of a stud. The mounting plate
is also ideal for installing the controller in a lectern.
NOTE: If necessary, consult the latest revision of the APAD Installation and
Operations Guide (Doc. 6455) for a complete list of mounting options. The
document is available from the Crestron website (http://www.crestron.com/manuals).
Installation Guide – DOC. 6063A
Trim Ring Mount Kits: TMK-1000L & WMKT-1000L • 1
Trim Ring Mount Kits
Crestron TMK-1000L & WMKT-1000L
Setup
Supplied Hardware
The TMK-1000L consists of a metal trim ring that attaches to the BB-1000L or
PMK-1000L. The WMKT-1000L consists of the trim ring found in the TMK-1000L
as well as a mounting plate.
The mounting plate provides the necessary support for post-construction
applications. Two overlay cutout templates (2005028) are supplied. One is in the
shape of the required opening; the other is similar to a frame, with the inner area of
the frame the shape of the required opening. (Refer to the illustrations on pages 3 and
4.) Use the template that is most convenient.
Supplied Hardware for the TMK-1000L and WMKT-1000L
DESCRIPTION
PART NUMBER
QUANTITY
Metal, Plate, Trim Ring
2004809
1
Metal, Plate, Mounting
(WMKT-1000L only)
2004807
1
Screw, #04-40 x 2”, Pan, Phil
(WMKT-1000L only)
2018793
4
Overlay, Template, Wall Cutout
(WMKT-1000L Only)
2005028
1
The dimensions of the TMK-1000L/WMKT-1000L are shown below and on the next
page.
Dimensional Drawing – Trim Ring
4.71 in
(11.96 cm)
0.50 in
(1.27 cm)
4.70 in
(11.95 cm)
2.23 in
(5.66 cm)
2 • Trim Ring Mount Kits: TMK-1000L & WMKT-1000L
Installation Guide – DOC. 6063A
Crestron TMK-1000L & WMKT-1000L
Trim Ring Mount Kits
Dimensional Drawing – Mounting Plate
5.91 in
(15.00 cm)
0.06 in
(0.16 cm)
5.77 in
(14.66 cm)
Drywall Cutout Template and Dimensions (supplied with WMKT-1000L only), 1 of 2
4 1/2 in
(115 mm)
4 1/2 in
(115 mm)
Installation Guide – DOC. 6063A
Trim Ring Mount Kits: TMK-1000L & WMKT-1000L • 3
Trim Ring Mount Kits
Crestron TMK-1000L & WMKT-1000L
Drywall Cutout Template and Dimensions (supplied with WMKT-1000L only), 2 of 2
6 in
(152 mm)
3/4 in
(19 mm)
4 1/2 in
(115 mm)
11/16 in
(18 mm)
5 7/8 in
(150 mm)
4 1/2 in
(115 mm)
Installation
This section provides an installation procedure for each Trim Ring Mount Kit. The
“TMK-1000L Procedure” starts below and the “WMKT-1000L Procedure” starts on
page 6. Be sure to review each procedure before starting.
TMK-1000L Procedure
This section provides the necessary steps for the assembly of the TMK-1000L with
either the BB-1000L or PMK-1000L. It is assumed that the BB-1000L or
PMK-1000L has been secured to the stud according to the instructions in the latest
revisions of their Installation Guides (Doc. 6060 and Doc. 6061 respectively). It is
also assumed that drywall is in place and a rectangular cutout for the controller is
made in the drywall.
Complete the steps in the order provided. The only tool required and not supplied is
a level.
CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity
above and below the controller for heat dissipation.
NOTE: When installing into the PMK-1000L, verify that the 18 AWG bus wire
securing the cables for the controller remains attached.
1.
Verify that the rectangular cutout in the drywall is as level as possible.
2.
Insert the symmetrical trim ring into the opening, as shown in the
illustration on the following page.
4 • Trim Ring Mount Kits: TMK-1000L & WMKT-1000L
Installation Guide – DOC. 6063A
Crestron TMK-1000L & WMKT-1000L
Trim Ring Mount Kits
Insert Trim Ring into Opening
IMPORTANT
MAKE DRYWALL CUTOUT AS LEVEL
AND CLEAN AS POSSIBLE.
THE TRIM RING ONLY ALLOWS MINOR
ADJUSTMENTS OF THE CONTROLLER.
TRIM RING
(2004809)
NOTE: The required PMK-1000L or BB-1000L is not shown.
3.
Installation Guide – DOC. 6063A
When the trim ring is in position, bend the top two flanges of the ring
upward and the bottom two flanges downward.
•
If mounting into the PMK-1000L, bend the flanges approximately 90
degrees.
•
If mounting into the BB-1000L, bend the flanges back as far as they
can go.
4.
Run the necessary cables for the controller and secure them behind the
drywall.
5.
The controller can be installed using the four tapped holes in the
PMK-1000L or BB-1000L. Refer to the latest revision of the APAD
Installation and Operations Guide (Doc. 6455) for details. Refer also to the
comprehensive illustration on the following page.
Trim Ring Mount Kits: TMK-1000L & WMKT-1000L • 5
Trim Ring Mount Kits
Crestron TMK-1000L & WMKT-1000L
Controller Mounting Using TMK-1000L – Exploded View
PMK-1000L
DRYWALL
TRIM RING
(2004809)
APAD
APAD
MOUNTING SCREWS
(4) #04-40 X 2"
(2018793)
WMKT-1000L Procedure
This section provides the necessary steps for the assembly and installation of the
WMKT-1000L into a wall. Review the procedure and complete the steps in the order
provided. The only tools or materials required and not supplied are a drywall saw or
equivalent and a level.
CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity
above and below the controller for heat dissipation.
1.
Locate an area on the wall that is free of miscellaneous wiring and studs.
2.
Make a small hole near the middle of the designated site; verify that the
location is suitable.
NOTE: Make the cutout as level and smooth as possible. The mounting plate allows
for only minor leveling adjustments. If a larger cutout is made accidentally, consider
purchasing the Crestron Mud Mount Kit, MMK-1000L. Together with the mounting
plate supplied with the WMKT-1000L, it provide a cost-effective means of
correction. Essentially, the combination of these two kits makes up the Crestron Mud
Mount Kit for the wall, WMKM-1000L. Simply follow the “WMKM-1000L
Procedure” in the latest revision of the Mud Mount Kits Installation Guide (Doc.
6062).
3.
Use the drywall saw or equivalent to produce a level, rectangular cutout in
the drywall as shown on page 3 or 4.
4.
Insert the trim ring into the opening, as shown in the illustration on the
following page.
6 • Trim Ring Mount Kits: TMK-1000L & WMKT-1000L
Installation Guide – DOC. 6063A
Crestron TMK-1000L & WMKT-1000L
Trim Ring Mount Kits
Insert Trim Ring into Opening
IMPORTANT
MAKE DRYWALL CUTOUT AS LEVEL
AND CLEAN AS POSSIBLE.
THE TRIM RING ONLY ALLOWS MINOR
ADJUSTMENTS OF THE CONTROLLER.
MOUNTING PLATE
(2004807)
TRIM RING
(2004809)
5.
Carefully pass the mounting plate through the opening and hold it against
the interior surface of the drywall.
6.
When the mounting plate is in position, bend the top two flanges of the trim
ring upward (approximately 90 degrees) and the bottom two flanges
downward (approximately 90 degrees). Refer to the illustration on the
following page.
NOTE: The mounting plate will have a slight play; this is normal. It allows for
minor adjustments to the controller during installation.
Installation Guide – DOC. 6063A
Trim Ring Mount Kits: TMK-1000L & WMKT-1000L • 7
Trim Ring Mount Kits
Crestron TMK-1000L & WMKT-1000L
Bend Flanges
7.
Run the necessary cables for the controller and secure them behind the
drywall.
8.
The controller can be installed using the four tapped holes in the mounting
plate. Refer to the latest revision of the APAD Installation and Operations
Guide (Doc. 6455) for details. Refer also to the comprehensive illustration
on the following page.
8 • Trim Ring Mount Kits: TMK-1000L & WMKT-1000L
Installation Guide – DOC. 6063A
Crestron TMK-1000L & WMKT-1000L
Trim Ring Mount Kits
Controller Mounting Using WMKT-1000L – Exploded View
MOUNTING PLATE
(2004807)
DRYWALL
TRIM RING
(2004809)
APAD
APAD
MOUNTING SCREWS
(4) #04-40 X 2"
(2018793)
Installation Guide – DOC. 6063A
Trim Ring Mount Kits: TMK-1000L & WMKT-1000L • 9
Trim Ring Mount Kits
Crestron TMK-1000L & WMKT-1000L
Resources
Industry Compliance
As of the date of manufacture, the TMK-1000L and WMKT-1000L have been tested
and found to comply with specifications for CE marking.
Reference Documents
The latest version of all documents mentioned within the guide can be obtained from
the Crestron website (www.crestron.com/manuals). This link will provide a list of
product manuals arranged in alphabetical order by model number.
List of Related Reference Documents
DOCUMENT TITLE
APAD Wall Mount LCD Controller
BB-1000L Back Box
MMK-1000L and WMKM-1000L Mud Mount Kits
PMK-1000L Pre-Construction Mounting Kit
Further Inquiries
If you cannot locate specific information or have questions after reviewing this
guide, please take advantage of Crestron's award winning customer service team by
calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876].
For assistance in your local time zone, refer to the Crestron website
(www.crestron.com/offices) for a listing of Crestron worldwide offices.
You can also log onto the online help section of the Crestron website
(www.crestron.com/onlinehelp) to ask questions about Crestron products. First-time
users will need to establish a user account to fully benefit from all available features.
Future Updates
As Crestron adds improvements to the TMK-1000L and WMKT-1000L, additional
information may be made available as manual updates. These updates are solely
electronic and serve as intermediary supplements prior to the release of a complete
technical documentation revision.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
10 • Trim Ring Mount Kits: TMK-1000L & WMKT-1000L
Installation Guide – DOC. 6063A
Crestron TMK-1000L & WMKT-1000L
Trim Ring Mount Kits
Return and Warranty Policies
Merchandise Returns / Repair Service
1.
No merchandise may be returned for credit, exchange or service without prior authorization
from CRESTRON. To obtain warranty service for CRESTRON products, contact an
authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory
and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying
the nature of the problem, name and phone number of contact person, RMA number and
return address.
2.
Products may be returned for credit, exchange or service with a CRESTRON Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped freight
prepaid to CRESTRON, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with
RMA number clearly marked on the outside of all cartons. Shipments arriving freight collect
or without an RMA number shall be subject to refusal. CRESTRON reserves the right in its
sole and absolute discretion to charge a 15% restocking fee plus shipping costs on any
products returned with an RMA.
3.
Return freight charges following repair of items under warranty shall be paid by CRESTRON,
shipping by standard ground carrier. In the event repairs are found to be non-warranty, return
freight costs shall be paid by the purchaser.
CRESTRON Limited Warranty
CRESTRON ELECTRONICS, Inc. warrants its products to be free from manufacturing defects in materials
and workmanship under normal use for a period of three (3) years from the date of purchase from
CRESTRON, with the following exceptions: disk drives and any other moving or rotating mechanical
parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touchscreen display and
overlay components are covered for 90 days; batteries and incandescent lamps are not covered.
This warranty extends to products purchased directly from CRESTRON or an authorized CRESTRON
dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's warranty, if
any.
CRESTRON shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended or if it has been subjected to misuse, accidental
damage, modification or improper installation procedures. Furthermore, this warranty does not cover any
product that has had the serial number altered, defaced or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
CRESTRON be liable for incidental or consequential damages of any kind (property or economic damages
inclusive) arising from the sale or use of this equipment. CRESTRON is not liable for any claim made by a
third party or made by the purchaser for a third party.
CRESTRON shall, at its option, repair or replace any product found defective, without charge for parts or
labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered only by the
unexpired portion of the warranty.
Except as expressly set forth in this warranty, CRESTRON makes no other warranties, expressed or
implied, nor authorizes any other party to offer any warranty, including any implied warranties of
merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by law are
limited to the terms of this limited warranty. This warranty statement supersedes all previous warranties.
Trademark Information
All brand names, product names and trademarks are the sole property of their respective owners. Windows is a registered trademark
of Microsoft Corporation. Windows95/98/Me/XP/Vista and WindowsNT/2000 are trademarks of Microsoft Corporation.
Installation Guide – DOC. 6063A
Trim Ring Mount Kits: TMK-1000L & WMKT-1000L • 11
Crestron Electronics, Inc.
15 Volvo Drive Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Installation Guide – DOC. 6063A
(2002107)
01.08
Specifications subject to
change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement