EverFocus | EQH5102 | Specifications | EverFocus EQH5102 Specifications

EverFocus EQH5102 Specifications
 EQH5102 1080p Mini Box Camera User’s Manual ** Lens not included. Copyright © EverFocus Electronics Corp, Release Date: July, 2012 Cautions Please read this manual first to ensure correct installation and operation. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. 1. Do not install the camera near electric or magnetic fields. Install the camera away from TV / radio transmitters, magnets, electric motors, transformers and audio speakers, because the electromagnetic fields generated by these devices may distort the video image or otherwise interfere with camera functions. 2. Never disassemble the camera beyond the recommendations in this manual, nor apply materials to it other than those recommended herein. Improper disassembly or introduction of corrosive materials may result in equipment failure or other damage. 3. Try to avoid pointing the camera toward the sun. In some circumstances, direct sunlight may cause permanent damage to the sensor and / or internal circuits. It may also create unbalanced illumination that may be beyond the camera’s ability to compensate. 4. Keep the power cable away from water and other liquids. Never touch the power cable with wet hands. Touching a wet power cable with your hands or touching the power cable with wet hands may result in electric shock. 5. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may cause equipment failure, electric shock or, in extreme cases, fire. 6. Cleaning For cameras with interchangeable lenses, do not touch the surface of the sensor directly with your hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera body. Do not use complex solvents, or corrosive or abrasive agents to clean any part of the camera. 7. Do not operate the camera beyond the specified temperature, humidity and power source levels. This camera is suitable for indoor operation only. Use the camera at temperatures between 0°C ~ 45°C (32°F ~ 113°F) and humidity between 20 ~ 80%. The input power source should be 12VDC. The use of a properly fused or “Class 2 Limited Power Source” power supply is highly recommended. 8. Mounting Select a solid mounting surface that will support the weight of the camera and any additional loading from wind, snow, ice or other factors. Securely attach the camera to the mounting surface using screws and anchors that will properly support the camera. If necessary, (e.g. when mounting the camera to a drop ceiling, or unsupported ceiling) use a safety wire to provide additional support for the camera. i
Safety Notice Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -­‐ Reorient or relocate the receiving antenna. -­‐ Increase the separation between the equipment and receiver. -­‐ Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected. -­‐ Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ATTENTION! This is a class A product which may cause radio interference in a domestic environment; in this case, the user may be urged to take adequate measures. This Product is RoHS compliant. WEEE Your EverFocus product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-­‐of-­‐life, should be disposed of separately from your household waste. Please, dispose of this equipment at your local community waste collection/recycling centre. In the European Union there are separate collection systems for used electrical and electronic product. Please, help us to conserve the environment we live in!
ii
Contents 1. INTRODUCTION ........................................................................................ 1 1.1 PACKING LIST .............................................................................................................. 1 1.2 FEATURES .................................................................................................................. 1 2. OVERVIEW ............................................................................................... 2 3. INSTALLATION .......................................................................................... 2 3.1 LENS INSTALLATION AND ADJUSTMENT .............................................................................. 2 3.2 TOP / BOTTOM-­‐MOUNT ............................................................................................... 3 4. BASIC CONNECTION .................................................................................. 3 5. CONFIGURATION IN THE OSD MENU.......................................................... 3 5.1.1 EXPOSURE.............................................................................................................................. 4 6. SPECIFICATIONS .................................................................................... 10 7. APPENDIX ............................................................................................. 11 7.1 OSD MENU STRUCTURE ............................................................................................... 11 iii
EQH5102 1080p Mini Box Camera 1. Introduction The EQH5102 is an HDcctv indoor mini box camera. Based on a progressive scan CMOS sensor for HD 1080p resolution 100% digital images, it delivers vastly superior video quality compared to traditional CCTV images. This superior resolution not only captures more critical evidentiary information, but the inherent ability for megapixel video also extends the area of coverage, expedites completion of investigations, resolves complaints and reduces both capital and operational costs. No major upgrade to the IT network is required to deploy this powerful technology; HDcctv cameras communicate at digital speeds up to 1.5 Gb/s over existing or new coaxial cable (RG59 or other types for longer distances), using industry standard BNC connectors. The EQH5102 allows flexible choices of megapixel manual & DC iris control lenses with C / CS mount for outstanding coverage in a wide range of demanding surveillance environments while delivering stunning HD image quality. 1.1 Packing List
•
•
•
Camera body x 1 Power Pigtail Cable x 1 User Manual x 1
•
Lens Cover x1 •
C-­‐mount lens adapter x 1
1.2 Features •
•
•
•
•
•
•
•
•
Real time HDcctv 1080p HD video over coax for superlative image detail 1/3” 2.1 megapixel Color Progressive CMOS sensor CS/C mount, manual and DC iris control for flexible choice of HD Megapixel lenses Provides 3D DNR/ DSS to improve image clarity, particularly in low light scenes Electronic Lens Shading Compensation to offset diminished light transmission through lens periphery for uniform image illumination CTB [Contrast Boost] to deliver properly exposed images despite bright light sources, deep shadows and/or unbalanced lighting in the same scene Supports Digital Zoom/ BLC [Back Light Compensation]/ HSMASK [Highlight Suppression Mask]/ Privacy Zones (up to 32) DPC [Defect Pixel Correction] Dead pixel compensation for increased clarity and extended service life SD TV Out for aim and focus using a standard hand held test monitor 1
EQH5102 1080p Mini Box Camera
2. Overview No. Name Descriptions 1 HDcctv Output Connects to a HD device using a 75 Ohm BNC-­‐type coaxial cable. 2 OSD Menu Joystick Use the joystick to configure the settings in the OSD menu. 3 Screwless Terminal Strip Connects to a 12VDC power, RS-­‐485 and MD (Motion Detect) source. 4 Power LED Glows red then power is present. 5 Grounding Stud Ensuring a good grounding when used. 6 Test-­‐Out Connects to a SD CVBS monitor for setting image aim and focus. 3. Installation 3.1 Lens Installation and Adjustment You can install either a CS-­‐mount or a C-­‐mount lens into the camera. It is recommended to use a lens with aperture ratio of F/1.2 or lower. Please refer to the following reference steps. CS-­‐Mount Lens: 1.
Remove the cover cap from the camera body. 2.
Install the lens into the camera body. 3.
Adjust the lens using the Focus / Zoom Screws. 2
EQH5102 1080p Mini Box Camera
If you are using a DC Auto Iris lens: 1.
Remove the cover cap from the camera body. 2.
Install the lens into the camera body. 3.
Connect the DC cable to the DC Auto Iris Lens Connector. 4.
Lock the Focus Screw. C-­‐Mount Lens: 1.
Remove the cover cap from the camera body. 2.
Install the lens into the camera body using the supplied C-­‐mount lens adapter. 3.
Adjust the lens using the Focus / Zoom Screws. Warning: Installing a C-­‐mount lens without the C-­‐mount lens adapter may damage the camera sensor. 3.2 Top / Bottom-­‐Mount You can use a mounting bracket and screw it on the top of the camera body to suspend the camera, or on the bottom of the camera body to support the camera. 4. Basic Connection 1.
Connect the camera to an HD device, such as an HDcctv DVR, to display the image. 2.
Connect the camera to a 12VDC power source using the supplied Power Cable. You can optionally use the supplied Power Pigtail Cable or a power adapter to connect the Power Cable to the power source. The power LED will be lit in red. 3.
Connect the camera to a CVBS portable monitor for setting image aim and focus before mounting the camera. 5. Configuration in the OSD Menu You can use the Joystick on the rear panel of the camera to configure camera settings in the OSD menu. For details on the OSD menu structure, see OSD Menu Structure in Appendix. 3
EQH5102 1080p Mini Box Camera
5.1 OSD Menu Press the Enter / Confirm button on the Joystick. The Setup Menu in the OSD appears. 5.1.1 EXPOSURE Press the Enter / Confirm button to enter the submenu. BRIGHTNESS Use the  and  buttons to increase or decrease the screen brightness from 0 to 20. MODE Indoor Select this mode when the color temperature of the video image is similar to that found in indoor environments (around 5100 to 5300°K). Outdoor Select this mode when the color temperature of the video image is similar to that found in outdoor environments (around 3,000°K to 3,200°K) LENS You can select the type of the lens. Two types are available: Manual and DC. By default, the DC type lens is selected. 4
EQH5102 1080p Mini Box Camera
Shutter Use the  and  buttons to adjust the shutter speed. The options include: 1/25 ~ 1/60000, FLK, and AUTO. Any selection other than AUTO and 1/25 will disable the DSS function. DSS (Digital Slow Shutter) DSS is used to maintain a vivid screen image by automatically boosting low light levels. The value is between x2 ~ X4 and OFF. AGC (Auto Gain Control) The higher the AGC value, the brighter the screen, but the level of noise will also be increased. The options include: 0~10. 5.1.2 COLOR Press the Enter / Confirm button to enter the submenu. AWB (Auto White Balance) This mode can be used to view areas with a color temperature range. Use the  and  buttons to select the AWB options. The options include: AUTO, AUTO EXTN, PRESET, MANUAL COLOR TEMP, R-­‐GAIN and B-­‐GAIN. • AUTO – Around 2500 to 9500°K • AUTO EXTN (Extension) – Around 2300 to 10800°K • PRESET – Use a pure white background to preset the white balance value. • MANUAL COLOR TEMP – Use the  and  buttons to adjust the speed. The options include: LOW, MIDDLE and HIGH • R-­‐GAIN and B-­‐GAIN –The options include: 0~20. CHROMA Use the  and  buttons to increase or decrease the CHROMA from 0 to 20. R-­‐OFFSET/B-­‐OFFSET Use the  and  buttons to increase or decrease the Red and Blue offset from 0 to 20. 5
EQH5102 1080p Mini Box Camera
5.1.3 IMAGE Press the Enter / Confirm button to enter the submenu. SHARPNESS Use the  and  buttons to increase or decrease the SHARPNESS from 0 to 10. MIRROR/FLIP Turn it on to reverse/ flip the image. DZOOM Turn it on to set up the zoom level PRIVACY Enter the submenu to set up the privacy masks; up to 31 zones can be created: ON ZONE NO: Use the  and  buttons to select the zone from 0 to 31. X, Y-­‐POS, SIZ: Enter the submenu to set up the position or size of the privacy mask zone. COLOR: Press to select a color for the selected privacy mask zone. TRANS: Press to select the transparency of mask zone. SHADING Turn it on to offset diminished light transmission through lens periphery for uniform image 6
EQH5102 1080p Mini Box Camera
illumination. DAY&NIGHT The options include MODE, AGC THRS, DELAY. A submenu can be entered if you select MODE. • MODE – Use the  and  buttons to select AUTO, COLOR and B&W. Switches to a B&W feed in low light conditions and then switches back to a Color feed in the daytime. • AGC THRS –Use the  and  buttons to select the AGC Threshold from 0 to 20. • DELAY – Set up the delay time in 0,5,10 and 30 seconds for the camera to switch between Day and Night. HLMASK Turn it on to select the level and color of the masking effect. CTB (Contrast Boost) Turn it on to deliver properly exposed images despite bright light sources, deep shadows and/or unbalanced lighting in the same scene. GAMMA Use the  and  buttons to increase or decrease the GAMMA from 0.45 to 0.75. 5.1.4 BLC Press the Enter / Confirm button to enter the submenu. MODE 7
EQH5102 1080p Mini Box Camera
Use the  and  buttons to select OFF and BLC. BLC OSD, POS and SIZ Select OFF to disable the BLC function, or select ON to enable the BLC function and for further setup. After selecting an area block, enter the BLC POS / SIZ and X/ Y setup page, a “POSITION” sign displayed on the screen. Use the direction buttons to move the area to the desired position. Press the Enter / Confirm button to confirm the position, a “SIZE” sign displayed on the screen. Use the direction buttons to adjust the size for the area. 5.1.5 3D-­‐DNR Press the Enter / Confirm button to enter the submenu. Switch to HIGH, MIDDLE, LOW and OFF to enable or disable noise reduction on dynamic recordings. 5.1.6 MOTION Press the Enter / Confirm button to enter the submenu. 8
EQH5102 1080p Mini Box Camera
RESOLUTION Use the  and  buttons to increase or decrease the RESOLUTION level from 0 to 4. SENSITIVITY Press to set up the sensitivity for the motion detection function. WINDOW TRANS Press to select the transparency of motion detect zone. WINDOW USE, POS and SIZ Select OFF to disable this function, or select ON to enable and for further setup. After selecting an area block, enter the BLC POS / SIZ and X/ Y setup page, a “POSITION” sign displayed on the screen. Use the direction buttons to move the area to the desired position. Press the Enter / Confirm button to confirm the position, a “SIZE” sign displayed on the screen. Use the direction buttons to adjust the size for the area. 5.1.7 SYSTEM Press the Enter / Confirm button to enter the submenu. DEFECT DET Press to select the DPC (Defective Pixel Correction) level of defect detector. Please notice; do not use this function without cover the lens. The camera will automatically correct pixel defects. Misoperation will cause the abnormal image. 9
EQH5102 1080p Mini Box Camera
CAM TITLE Switch to On and then enter the submenu to set up a camera name displayed on the screen. RS-­‐485 Use the  and  buttons to select ID, BAUDRATE, PROTOCOL and ID DISPLAY. The default of protocol is EVF-­‐1 (EverFocus). Version Press to display the firmware version of the camera. DOUT There are 4 options including 1080p 30FPS NTSC, 1080p 25FPS PAL, 720p 60FPS NTSC and 720p 50FPS PAL Language Select a language for the OSD text. Options include English, French, German, Simplified Chinese, Korean and Japanese. 6. Specifications Camera Pickup Device 1/3” Panasonic 2.1 megapixel Color Progressive CMOS sensor Image Pixels 1920(H) x 1080(V) Resolution Digital:1080p(30/25), 720p(60/50) Sensitivity Color: 0.4 lux, BW: 0.1 lux, Color DSS: 0.1 lux, BW DSS: 0.025 lux Video Output Digital(HDcctv Output): BT.1120, HDcctv/HD-­‐SDI: BNC connector Analogue(Test Out): NTSC/PAL CVBS(w/o WDR): BNC connector S/N Ratio More than 50 dB (AGC OFF) Lens DC/Manual AGC 0-­‐20 steps Shutter Speed AUTO/MANUAL(1/25(30)~1/60,000sec) 10
EQH5102 1080p Mini Box Camera
Digital Slow Shutter(DSS) On/Off(x4) Brightness 0-­‐20 BLC On/Off Contrast Boost(CTB) On/Off Day&Night Auto/Color/B&W Auto White Balance Auto/Auto extn/Preset/Manual Digital Noise Reduction(DNR) Off/Low/Middle/High Mirror On/Off Flip On/Off Sharpness 0 -­‐ 10 steps Lens Shading Compensation On/Off Digital Zoom 0 -­‐ 96 steps Privacy Mask 32 Zones, Programmable Motion Detection On/Off(Swith Output, Screwless terminal connector) RS -­‐ 485 2400~115200> baud, ID 1~255, Protocols: Pelco-­‐D/P, EverFocus EVF-­‐1; Screwless terminal connector Language English/French/German/Simplified Chinese/Japanese Power Source 12VDC, Screwless terminal connector Power Comsumption 12VDC: 2W max. Operating Environment 0°C~45°C/32°F~113°F (20%~80% Humidity) Dimensions(L x W x H) 89 x 46 x 48mm /3.5” x1.8” x1.9” Weight 0.193kg/0.434lbs Certifications FCC / CE 7. Appendix 7.1 OSD Menu Structure The default value is marked with a star “*”. No
. Main Sub Menu Sub Menu / Function 1 EXPOSURE BRIGHTNESS 1~20 (default=6) MODE INDOOR*, OUTDOOR LENS MANUAL, DC* 11
EQH5102 1080p Mini Box Camera
AUTO* SHUTTER MANUAL 1/25~1/60000 FLK DSS OFF, X2, X3, X4* AGC 0~10 (default=10) AUTO* AUTO extn AWB 2 3 COLOR IMAGE PRESET MANUAL COLOR TEMP LOW, MIDDLE, HIGH R-­‐GAIN 0~20 B-­‐GAIN 0~20 CHROMA 0~20 (default=7) R-­‐OFFSET 0~20 (default=12) B-­‐OFFSET 0~20 (default=5) SHARPNESS 0~10 (default=6) MIRROR ON, OFF* FLIP ON, OFF* D-­‐ZOOM 0~96 (default=0) OFF* PRIVACY SHADING ON ZONE NO 0~31 ZONE UP ON, OFF X-­‐POS 0~60 Y-­‐POS 0~40 X-­‐SIZ 0~60 Y-­‐SIZ 0~40 COLOR TRANS 0~4 ON*, OFF AUTO* NODE DAY&NIGHT COLOR B&W AGC THRS 0~20 (default=10) MARGIN 0~20 (default=) DELAY 0, 5*, 10, 30 SEC OFF* HLMASK ON LEVEL 0~20 (default=10) COLOR BLK*/WHT/YEL/CYN/GRN/MAG/RED/BLU 12
EQH5102 1080p Mini Box Camera
4 5 BLC 3D-­‐DNR CTB ON, OFF* GAMMA 0.45*, 0.5, 0.55, 0.65, 0.75 MODE OFF*, BLC BLC OSD ON, OFF* BLC POS-­‐X 0~20 (default=7) BLC POS-­‐Y 0~20 (default=7) BLC SIZ-­‐X 0~20 (default=5) BLC SIZ-­‐Y 0~20 (default=5) HIGH, MIDDLE*, LOW, OFF OFF* 6 MOTION ON DEFECT DET RESOLUTION 0~4 (default=1) SENSITIVITY 0~20 (default=10) WINDOW TRANS 0~6 (default=3) WINDOW USE ON, OFF* X-­‐POS 0~60 (default=4) Y-­‐POS 0~40 (default=6) X-­‐SIZ 0~60 (default=15) Y-­‐SIZ 0~40 (default=20) DPC LEVEL 000~255 (default=26) OFF* CAM TITLE ON ID RS-­‐485 7 SYSTEM STRING SET POSITION 1~255 (default=1) BAUDRATE 2400, 4800, 9600*, 19200, 38400, 57600, 115200 PROTOCOL PELCO-­‐D, PELCO-­‐P, EVF-­‐1* ID DISPLAY ON, OFF DOUT SCALE FULL*, COMP DOUT FORMAT 720P, 1080P* DOUT FPS 50, 60 ,25*, 30 FREQ 50*, 60 HZ CVB PAL*, NTSC LANGUAGE English, Simplified Chinese, Japanese, Korean, French, German RESET PUSH, PUSHING 13
EverFocus Electronics Corp. EverFocus Taiwan: 12F, No.79, Sec. 1, Shin-­‐Tai Wu Road, Hsi-­‐Chih, Taipei, Taiwan TEL: +886 2 2698 2334 FAX: +886 2 2698 2380 www.everfocus.com.tw marketing@everfocus.com.tw EverFocus Europe -­‐ Germany: Albert-­‐Einstein-­‐Strasse 1, D-­‐46446 Emmerich, Germany TEL: +49 2822 93940 FAX: +49 2822 939495 www.everfocus.de info@everfocus.de EverFocus China -­‐ Beijing: Room 609, Technology Trade Building, Shangdi Information Industry Base, Haidian District, Beijing 100085, China TEL: +86 10 6297 3336~39 FAX: +86 10 6297 1423 www.everfocus.com.cn marketing@everfocus.com.cn EverFocus China -­‐ Shenzhen: 4F, No. 2, D4 Building, Wan Yelong Industrial Park, Tangtou Road, Shiyan, Baoan, Shenzhen, Guangdong 518101, China TEL: +86 755 2765 1313 FAX: +86 755 2765 0337 www.everfocus.com.cn marketing@everfocus.com.cn EverFocus USA -­‐ California: 1801 Highland Avenue, Unit A, Duarte, CA 91010, USA TEL: +1 626 844 8888 FAX: +1 626 844 8838 www.everfocus.com sales@everfocus.com EverFocus USA -­‐ New York: 415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA TEL: +1 631 436 5070 FAX: +1 631 436 5027 www.everfocus.com sales@everfocus.com EverFocus Japan: 5F, Kinshicho City Building, 2-­‐13-­‐4 Koto-­‐Bashi,Sumida-­‐Ku, Tokyo, 130-­‐0022, Japan TEL: +81 3 5625 8188 FAX: +81 3 5625 8189 www.everfocus.co.jp info@everfocus.co.jp EverFocus Europe -­‐ UK: Unit 12, Spitfire Business Park, Hawker Road, Croydon Surrey, CR0 4WD, UK TEL: +44 20 8649 9757 / +44 845 430 9999 FAX: +44 20 8649 9907 www.everfocusuk.co.uk salesuk@everfocus.com EverFocus India: Suite 803, Housefin Bhavan, C-­‐21, Bandra Kurla Complex, Bandra (East), Mumbai 400051, India TEL: +91 22 6128 8700 FAX: +91 22 6128 8705 www.everfocus.in sales@everfocus.in Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed of
separately from your household
waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte am
Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
N 
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising