ps-45-15
31506-PS
45W Single Output Switching Power Supply
PS-45-15
¡½ Features :
¡EUniversal AC input/Full range
¡ Low leakage current<0.75mA
E
¡ Protections: Short circuit / Overload / Over voltage
E
¡ Cooling by free air convection
E
¡ 100% full load burn-in test
E
¡ Fixed switching frequency at 65KHz
E
¡ 2 years warranty
E
..
SPECIFICATION
MODEL
OUTPUT
PS-45-15
DC VOLTAGE
15V
RATED CURRENT
3A
CURRENT RANGE
0 ~ 3.5A
RATED POWER
45W
OUTPUT POWER (max.)
Rated output power for convection; 52W (+3.3V : 35W) with 18 CFM min.
RIPPLE & NOISE (max.) Note.2 100mVp-p
14.25 ~ 16.5V
VOLTAGE ADJ. RANGE
VOLTAGE TOLERANCE Note.3 ¡Ó2.0%
LINE REGULATION
INPUT
¡Ó2.0%
SETUP, RISE TIME
800ms, 30ms at full load
HOLD UP TIME (Typ.)
60ms at full load
VOLTAGE RANGE
90 ~ 264VAC
FREQUENCY RANGE
47 ~ 440Hz
EFFICIENCY(Typ.)
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVERLOAD
PROTECTION
OVER VOLTAGE
WORKING TEMP.
WORKING HUMIDITY
ENVIRONMENT STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
SAFETY STANDARDS
SAFETY & WITHSTAND VOLTAGE
EMC
(Note 4)
OTHERS
127 ~370VDC
77%
0.8A/115VAC
0.56A/230VAC
COLD START 15A/115VAC
<0.75mA / 240VAC
30A/230VAC
53 ~ 75W(3.3V : 36 ~ 55W) rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed.
17.25 ~ 20.25V
Protection type : Hiccup mode, recovers automatically after fault condition is removed.
-10 ~ +60¢J (Refer to "Derating Curve")
20 ~ 90% RH non-condensing
-20 ~ +85¢J, 10 ~ 95% RH
¡Ó0.05%/¢J (0 ~ 50¢J)
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
UL60950-1, TUV EN60950-1 approved
I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
ISOLATION RESISTANCE
EMC EMISSION
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25¢J/ 70% RH
Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3
EMC IMMUNITY
MTBF
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A
300.7K hrs min. MIL-HDBK-217F (25¢J)
127*76*28mm (L*W*H)
0.19Kg; 72pcs/15.6Kg/1.35CUFT
DIMENSION
PACKING
NOTE
¡Ó1.0%
LOAD REGULATION
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25¢J of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”
(as available on http://www.meanwell.com)
5. Mounting holes M1 and M2 should be grounded for EMI purposes.
6. Heat Sink HS1,HS2 can not be shorted.
File Name:PS-45-S15
2013-02-23
31506-PS
PS-45-15
45W Outputs Switching Power Supply
Mechanical Specification
Unit:mm
127
5.6
5.6
115.8
FG
HS1
M1
M2
CN1
64.8
76
1
CN2
1
2
3
4
5
6
2
FS1
AC FUSE
F4A/250V
HS2
3.
8
28
4£r
AC Input Connector (CN1) : Molex 5277-02 or equivalent
Pin No.
1
2
Assignment
AC/N
AC/L
Mating Housing
Terminal
Molex 5195
or equivalent
Molex 5194
or equivalent
DC Output Connector (CN2) : Molex 5273-06 or equivalent
Pin No.
1,2,3
4,5,6
Assignment
+V
-V
Mating Housing
Molex 5195
or equivalent
Terminal
Molex 5194
or equivalent
HS1,HS2 can not be shorted
Block Diagram
fosc : 65KHz
RECTIFIERS
&
FILTER
EMI
FILTER
I/P
FG
16
OUTPUT VOLTAGE (V)
60
3.3V,5V
40
20
10
20
30
40
50
AMBIENT TEMPERATURE (¢J)
60
(HORIZONTAL)
300
14
250
+12V
12
200
10
150
8
+12V
100
6
50
4
25
60
80
100
120
140
160
180
200
220
240
OUTPUT RIPPLE (mVp-p)
OTHERS
80
LOAD (%)
O.V.P.
Static Characteristics (12V)
100
0
+V
-V
DETECTION
CIRCUIT
PWM
CONTROL
O.L.P.
Derating Curve
-10
RECTIFIERS
&
FILTER
POWER
SWITCHING
264
INPUT VOLTAGE (V) 60Hz
File Name:PS-45-S15
2013-02-23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising