1W 3.3V Green Power LED 75lm Order code: 55-1869 Features:

1W 3.3V Green Power LED 75lm Order code: 55-1869 Features:
55-1869:Layout 1
16/6/14
14:46
Page 1
1W 3.3V Green
Power LED 75lm
Order code: 55-1869
Features:
•
•
•
•
•
Outline dimensions:
Highest luminous flux
Super energy efficiency
Long lifetime operation
Superior ESD resistance
Superior UV resistance
Applications:
Back view
Read lights (car, bus, aircraft)
Portable (flashlight, bicycle)
Bollards/security/garden
Traffic signaling/beacons
Indoor/outdoor commercial lights
Automotive ext
3.5
5.5
6.05
1.05
Absolute maximum rating
(Ta=25°C)
Item
14.5
Symbol
Value
Unit
DC Forward current
IF
400
mA
Pulse forward current*
IFP
500
mA
Reverse voltage
VR
5
V
PD
1600
mW
Operating temperature
Topr
–30 to +85
°C
Storage temperature
Tstg
–40 to +100
°C
Lead soldering temperature
Tsol
260°C/5 sec
–
Power dissipation
* Pulse width max. 10ms
ESD Protection Diode
Unit: mm
Tolerance: ±0.30mm
0.2
0.1
•
•
•
•
•
•
2.0
Directivity:
90°
90°
1
0.5
0
0.5
1
Duty ratio max 1/10
Electrical – Optical characteristics (Ta=25°C)
Item
Symbol
Condition
Min.
Typ.
Max.
Unit
DC Forward voltage
VF
IF = 350mA
3.0
3.3
4.0
V
DC Reverse current
IR
VR = 5V
–
–
10
µA
Forward operating current (DC):
400
λD
Luminous flux
ΦV
50% Power angle
2θ1/2
IF = 350mA
IF = 350mA
IF = 350mA
520
65
–
525
530
75
120
–
–
nm
lm
deg
300
If( Forward Current: mA)
Domi. wavelength
350
RJ-A=60°C/W
250
RJ-A=50°C/W
200
RJ-A=40°C/W
150
RJ-A=30°C/W
100
50
0
Note: Don’t drive at rated current more than 5s without heat sink
for Xeon 1 emitter series.
0
25
50
75
100
125
Ta (Ambient Temperature: °C)
Page 1 of 2
www.rapidonline.com
55-1869:Layout 1
16/6/14
14:46
Page 2
1W 3.3V Green
Power LED 75lm
Order code: 55-1869
Handling of silicone lens LEDs
Notes for handling of silicone lens LEDs
• Do not use a force of over 3kgf impact or pressure on the silicone lens, otherwise it will
cause a catastrophic failure
• The LEDs should only be picked up by making contact with the sides of the LED body
• Avoid touching the silicone lens especially with sharp tools such as tweezers
• Store the LEDs away from dusty areas or seal the product against dust
• When populating boards in SMT product, there are basically no restrictions regarding the
form of the pick and place nozzle, expect that mechanical pressure on the silicon lens must
be prevented
• Do not mould over the silicone lens with another resin . . . epoxy, urethane, etc.
Page 2 of 2
www.rapidonline.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising