HP Compaq Presario,Presario SG202 System information

HP Compaq Presario,Presario SG202 System information
Compaq Presario CQ41 Notebook PC
Maintenance and Service Guide
Document Part Number: 598099-001
December 2009
This guide is a troubleshooting reference used for maintaining and servicing the computer. It provides
comprehensive information on identifying computer features, components, and spare parts; troubleshooting
computer problems; and performing computer disassembly procedures.
© Copyright 2009 Hewlett-Packard Development Company, L.P.
ATI and ATI Mobility Radeon are trademarks of Advanced Micro Devices, Inc. Bluetooth is a trademark owned by its proprietor and
used by Hewlett-Packard Company under license. Intel, Arrandale, and Core are trademarks of Intel corporation in the U.S. and other
countries. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. SD Logo is a trademark of its proprietor.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in
the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an
additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
First Edition: December 2009
Document Part Number: 598099-001
Safety warning notice
Å
WARNING: To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly
on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface,
such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow
the AC adapter to contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the
AC adapter comply with the user-accessible surface temperature limits defined by the International Standard for Safety of
Information Technology Equipment (IEC 60950).
Contents
1 Product description
2 External component identification
Top components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
TouchPad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2
Buttons and speakers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5
Front components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6
Rear component . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7
Right-side components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8
Left-side components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9
Bottom components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10
Wireless antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–11
Additional hardware components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–12
3 Illustrated parts catalog
Service tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
Computer major components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
Display assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–7
Plastics Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–8
Mass storage devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–9
Miscellaneous parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–10
Sequential part number listing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–11
4 Removal and replacement procedures
Preliminary replacement requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Tools required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Service considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Plastic parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Grounding guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2
Component replacement procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Service tag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5
Computer feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–6
Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–7
Hard drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–8
Memory module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–10
RTC battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–12
WLAN module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–14
Optical drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–20
Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–21
Maintenance and Service Guide
iv
Contents
Keyboard cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speaker assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Webcam/microphone module (select models only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Microphone module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Top cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bluetooth module and cable (select models only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modem module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power connector and cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heat sink/fan assembly or heat sink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fan (for models with UMA graphics subsystems) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4–23
4–25
4–27
4–33
4–34
4–35
4–38
4–40
4–42
4–44
4–46
4–48
4–52
4–56
4–57
5 Setup Utility
Starting Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Setup Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the language of Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Navigating and selecting in Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying system information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restoring default settings in Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exiting Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup Utility menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Configuration menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostics menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5–1
5–1
5–1
5–2
5–2
5–2
5–3
5–3
5–3
5–3
5–4
5–4
6 Specifications
Computer specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–1
14.1-in display specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–2
Hard drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–3
Blu-ray ROM DVD±R/RW SuperMulti DL Drive with LightScribe specifications. . . . . . . . . . . . . . . . . . 6–4
DVD±RW SuperMulti DL Drive with LightScribe specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–5
System DMA specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–6
System interrupt specifications (for models with discrete graphics subsystems) . . . . . . . . . . . . . . . . . . . . 6–6
System interrupt specifications (for models with UMA graphics subsystems) . . . . . . . . . . . . . . . . . . . . . . 6–7
System I/O address specifications (for models with discrete graphics subsystems) . . . . . . . . . . . . . . . . . . 6–8
System I/O address specification (for models with UMA graphics subsystems) . . . . . . . . . . . . . . . . . . . 6–10
7 Backup and recovery
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Creating recovery discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Backing up your information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Windows Backup and Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using system restore points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performing a recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recovering from the recovery discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
v
7–1
7–2
7–3
7–4
7–4
7–5
7–6
Maintenance and Service Guide
Contents
Recovering from the dedicated recovery partition (select models only) . . . . . . . . . . . . . . . . . . . . . . . 7–6
8 Connector pin assignments
Audio-in (microphone). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio-out (headphone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RJ-11 (modem) (select models only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RJ-45 (network) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Universal Serial Bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8–1
8–1
8–2
8–3
8–4
8–5
8–6
9 Power cord set requirements
Requirements for all countries and regions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–1
Requirements for specific countries and regions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–2
10 Recycling
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–1
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–1
Index
Maintenance and Service Guide
vi
1
Product description
Discrete graphics
subsystem memory
UMA graphics
subsystem memory
Compaq Presario CQ41 Notebook PC


Intel Arrandale™ CPU-uPGA Socket Single-Core
i5-520M (2.4 GHz, 3 MB L3 cache, 1066 MHz SC
Turbo)


Intel Arrandale CPU-uPGA Socket Single-Core
i5-540M (2.53 GHz, 3 MB L3 cache, 1066 MHz SC
Turbo)


Chipset
Intel™ HM55


Graphics
ATI Discrete Mobility Radeon™ HD4350 with 512
MB dedicated video memory

Category
Description
Product Name
Processors
Panel
Mobile Intel GMA Media Accelerator HD unified
memory architecture (UMA, integrated) with shared
video memory:

■ Up to 285 MB of video memory on computer
models equipped with 1 GB of main system
memory.
■ Up to 797 MB of video memory on computer
models equipped with 2 GB of main system
memory.
■ Up to 1309 MB of video memory on computer
models equipped with 3 GB of main system
memory.
■ Up to 1295 MB of video memory on computer
models equipped with 4 GB of main system
memory (32-bit OS).
■ Up to 1695 MB of video memory on computer
models equipped with 4 GB of main system
memory (64-bit OS).

14.1-in WXGA BrightView (1280 × 800) display
panel
16:10 wide aspect ratio


(Continued)
Maintenance and Service Guide
1–1
Product description
Discrete graphics
subsystem memory
UMA graphics
subsystem memory
2 customer-accessible/upgradable memory module
slots
Supports dual-channel memory
Supports up to 4 GB of system RAM,
1600 MHz, DDR3
Supports the following configurations:
■ 4096 MB total system memory
(2048 × 2, dual-channel)
■ 3072 MB total system memory (2048 + 1024)
■ 2048 MB total system memory
(1024 × 2, dual-channel)
■ 2048 MB total system memory (2048 × 1)
■ 1024 MB total system memory (1024 × 1)


Hard drive
Supports a 9.50-mm, 6.35-cm (2.50 in) hard drive
Customer-accessible
Serial ATA
Supports the following hard drives:
500 GB, 7200 rpm
320 GB, 7200 rpm
250 GB, 7200 rpm
160 GB, 7200 rpm


Optical drive
12.7 mm tray load
Serial ATA (SATA)
Fixed (removal of 1 screw required)
Customer-accessible
Parallel ATA
Supports no-optical-drive option
Supports the following drives:
■ DVD±R/RW SuperMulti DL Drive with LightScribe
■ Blu-ray ROM DVD±R/RW SuperMulti DL Drive
with LightScribe


Microphone
Single analog microphone


Audio
High-definition audio
Supports Microsoft® premium requirements
Presario-branded Altec Lansing speakers


Modem (select
models only)
56K MDC V.92 data/fax modem (select models only)


Webcam (select
models only)
VGA webcam
Fixed (no tilt)
Activity LED
640 × 480, 24 frames per second


Ethernet
Integrated 10/100 network interface card (NIC)


Category
Description
Memory
(Continued)
1–2
Maintenance and Service Guide
Product description
Discrete graphics
subsystem memory
UMA graphics
subsystem memory
Integrated WLAN options by way of wireless module
2 wireless antennas built into display assembly
Supports no-WLAN option
Support for the following WLAN formats:
Broadcom BCM4312 802.11b/g WLAN module
Atheros AR5009 802.11a/b/g/n WLAN module
Atheros AR9285 802.11b/g/n WLAN module


External media
cards
Digital Media Slot supporting Memory Stick (MS),
Memory Stick Pro (MSP), MultiMediaCard (MMC),
Secure Digital (SD) Memory Card, and xD-Picture
Card (XD). Adapter (purchased separately) provides
support for mini versions of SD, MMC, and MS Duo


Ports
Audio-in (stereo microphone)
Audio-out (stereo headphone)
RJ-11 modem (select models only)
HDMI v. 1.3b supporting 1080p with HDCP key
HP Smart Adapter power
RJ-45 network (Ethernet, includes link and
activity lights)
USB 2.0
VGA (Dsub 15-pin) supports the following
resolutions:
1920 × 1200 external resolution at 60 GHz
1600 × 1200 external resolution at 75 GHz
Hot plug/unplug with auto-detect
Category
Description
Wireless





Keyboard/pointing
devices
14.1-in keyboard
TouchPad with twoTouchPad buttons
Supports two-way scroll
Taps enabled as default

Power requirements
90 W HP Smart Adapter with localized cable
plug support (three-wire plug with ground pin,
supports three-pin DC connector)


65 W HP Smart Adapter with localized cable
plug support (three-wire plug with ground pin,
supports three-pin DC connector)
Battery option:
6-cell, 2.20 Ah (47 Wh) Li-ion battery


(Continued)
Maintenance and Service Guide
1–3
Product description
1–4
Discrete graphics
subsystem memory
UMA graphics
subsystem memory
Kensington Security Lock


Operating system
Preinstalled:
Windows® 7 Professional (64-bit or 32-bit OS)
Windows 7 Premium (64-bit or 32-bit OS)
Windows 7 Basic (32-bit OS)
FreeDOS


Serviceability
End-user replaceable parts:
AC adapter
Battery (system)
Hard drive
Memory modules
MiniCard components
Optical drive
WLAN module


Category
Description
Security
Maintenance and Service Guide
2
External component identification
Top components
TouchPad
Item
Component
Description
1
TouchPad light
White—TouchPad is enabled.
Amber—TouchPad is disabled.
2
TouchPad*
Moves the pointer and selects or activates items on the screen.
3
Left TouchPad button*
Functions like the left button on an external mouse.
4
TouchPad on/off button
Enables/disables the TouchPad.
5
TouchPad scroll zone
Scrolls up or down.
6
Right TouchPad button*
Functions like the right button on an external mouse.
*This table describes factory settings.
To view or change the pointing device preferences:
1. Select Start > Devices and Printers.
2. Right-click the device representing your computer.
3. Select Mouse settings.
Maintenance and Service Guide
2–1
External component identification
Lights
Item
Component
Description
1
Caps lock light
On—Caps lock is on.
2
Power lights (2)*
On—The computer is on.
Flashing—The computer is in the Sleep.
Off—The computer is off or in Hibernation.
3
Wireless light
Blue—An integrated wireless device, such as a wireless local area network
(WLAN) device and/or a Bluetooth® device, is on.
Amber—No wireless devices are detected.
4
Num lock light
On—The num lock is on or the embedded numeric keypad is enabled.
5
Battery light
On—The battery is charging.
Flashing—The battery reaches a low battery level or a critical battery level.
Off—If the computer is connected to an external power source, the light is off
when all batteries in the computer are fully charged. If the computer is not
connected to an external power source, the light is off until the battery
reaches a low battery level.
6
Drive light
Flashing—The hard drive or optical drive is being accessed.
*The two power lights display the same information. The light on the power button is visible only when the computer is open.
The power light on the front of the computer is visible whether the computer is open or closed.
2–2
Maintenance and Service Guide
External component identification
Buttons and speakers
Item
Component
Description
1
Speakers (2)
Produce sound.
2
Power button*
When the computer is off, press the button to turn on the computer.
When the computer is on, press the button to initiate Sleep.
When the computer is in Sleep, press the button to exit Sleep.
When the computer is in Hibernation, press the button to exit Hibernation.
If the computer has stopped responding and Windows shutdown procedures
are ineffective, press and hold the Power button for at least five seconds to
shut down the computer.
To learn more about power settings, select Start > Control Panel > System
and Security > Power Options.
3
Wireless button
Turns the wireless feature on or off but does not create a wireless
connection.
wireless network must be set up in order to establish a wireless
✎ Aconnection.
*This table describes factory settings. For information about changing factory settings, see the user guides located in Help and
Support.
Maintenance and Service Guide
2–3
External component identification
Keys
2–4
Item
Component
Description
1
esc key
Displays system information when pressed in combination with the fn key.
2
fn key
Executes frequently used system functions when pressed at the same time as
a function key or the esc key.
3
Windows logo key
Displays the Windows Start menu.
4
Embedded numeric keypad keys
Used like the keys on an external numeric keypad.
5
Windows applications key
Displays a shortcut menu for items beneath the pointer.
6
Navigation keys (home, pg up,
pg down)
Execute volume mute, volume up, or volume down when pressed at the same
time as the fn key.
7
Function keys
Execute frequently used system functions when pressed at the same time as
the fn key.
Maintenance and Service Guide
External component identification
Display
Item
Component
Description
1
Internal display switch
Turns off the display if the display is closed while the computer is turned on.
2
Internal microphone
Records sound.
3
Webcam light 
(select models only)
On—The webcam is in use.
4
Webcam 
(select models only)
Records video and captures still photographs.
Maintenance and Service Guide
2–5
External component identification
Front components
2–6
Item
Component
Description
1
Power light
On—The computer is on.
Flashing—The computer is in Sleep.
Off—The computer is off or in Hibernation.
2
Battery light
On—The battery is charging.
Flashing—The battery reaches a low battery level or a critical battery level.
Off—If the computer is connected to an external power source, the light is off
when all batteries in the computer are fully charged. If the computer is not
connected to an external power source, the light is off until the battery
reaches a low battery level.
3
Drive light
Flashing—The hard drive or the optical drive is being accessed.
4
Audio-in (microphone) jack
Connects an optional computer headset microphone, stereo array
microphone, or monaural microphone.
5
Audio-out (headphone) jack
Produces sound when connected to optional powered stereo speakers,
headphones, ear buds, a headset, or television audio.
Maintenance and Service Guide
External component identification
Rear component
Component
Description
Vent
Enables airflow to cool internal components.
computer fan starts up automatically to cool internal components
✎ The
and prevent overheating. It is normal for the internal fan to cycle on and
off during routine operation.
Maintenance and Service Guide
2–7
External component identification
Right-side components
2–8
Item
Component
Description
1
Optical drive light
Flashing—The optical drive is being accessed.
2
Optical drive
Reads and writes to optical discs.
3
USB ports (2)
Connect optional USB devices.
4
RJ-11 (modem) jack 
(select models only)
Connects a modem cable.
5
Power connector
Connects an AC adapter.
Maintenance and Service Guide
External component identification
Left-side components
Item
Component
Description
1
Security cable slot
Attaches an optional security cable to the computer.
security cable is designed to act as a deterrent, but it might not
✎ The
prevent the computer from being mishandled or stolen.
2
External monitor port
Connects an external VGA monitor or projector.
3
RJ-45 (network) jack
Connects a network cable.
4
HDMI port
Connects an optional video or audio device, such as a high-definition
television, or any compatible digital or audio component.
5
USB port
Connects an optional USB device.
6
Digital Media Slot light
On—Accessing a digital card.
7
Digital Media Slot
Supports the following optional digital card formats:
Memory Stick (MS)
Memory Stick Pro (MSP)
MultiMediaCard (MMC)
Secure Digital (SD) Memory Card
xD-Picture Card (XD)
Maintenance and Service Guide
2–9
External component identification
Bottom components
Item
Component
Description
1
Hard Drive bay
Holds the hard drive and, on select models, the wireless LAN (WLAN) device.
Ä
To prevent an unresponsive system, replace the wireless module only
with a wireless module authorized for use in the computer by the
governmental agency that regulates wireless devices in your country or
region. If you replace the module and then receive a warning message,
remove the module to restore computer functionality, and then contact
technical support through Help and Support.
2
Memory Module compartment
Contains the two memory module slots.
3
Mini Card compartment
Holds the real-time clock (RTC) battery and, on select models, the WLAN
device.
Ä
To prevent an unresponsive system, replace the wireless module only
with a wireless module authorized for use in the computer by the
governmental agency that regulates wireless devices in your country or
region. If you replace the module and then receive a warning message,
remove the module to restore computer functionality, and then contact
technical support through Help and Support.
4
Battery Release latch
Releases the battery from the battery bay.
5
Battery bay
Holds the battery.
6
Vents (3)
Enable airflow to cool internal components.
computer fan starts up automatically to cool internal components
✎ The
and prevent overheating. It is normal for the internal fan to cycle on and
off during routine operation.
2–10
Maintenance and Service Guide
External component identification
Wireless antennas
Two antennas send and receive signals from one or more wireless devices. These antennas are not visible from the
outside of the computer.
✎ For optimal transmission, keep the areas immediately around the antennas free from obstructions.
To see wireless regulatory notices, see the section of Regulatory, Safety and Environmental Notices that applies to
your country or region. These notices are located in Help and Support.
Maintenance and Service Guide
2–11
External component identification
Additional hardware components
Item
Component
Description
1
Power cord*
Connects an AC adapter to an AC outlet.
2
AC adapter
Converts AC power to DC power.
3
Battery*
Powers the computer when the computer is not plugged into external power.
*Batteries and power cords vary in appearance by country or region.
2–12
Maintenance and Service Guide
3
Illustrated parts catalog
Service tag
When ordering parts or requesting information, provide the computer serial number and model number provided on
the service tag.
Item
Component
Description
1
Product name
The name affixed to the front of the computer.
2
Serial number (s/n)
An alphanumeric identifier that is unique to each product.
3
Part number/Product number (p/n)
This number provides specific information about the product’s
hardware components. The part number helps a service
technician to determine which components and parts are needed.
4
Model description
An alphanumeric identifier used to locate documents, drivers, and
support for the computer.
5
Warranty period
The duration of the warranty period for the computer.
Maintenance and Service Guide
3–1
Illustrated parts catalog
Computer major components
3–2
Maintenance and Service Guide
Illustrated parts catalog
Item
Description
1
Display assembly (See “Display assembly,” for more display assembly internal component spare part information.)
2
3
Spare Part Number
14.1-in WXGA BrightView display with a microphone for models with discrete and UMA
graphics subsystems
487280-001
14.1-in WXGA BrightView display with a webcam/microphone for models with discrete and
UMA graphics subsystems
487281-001
Keyboard cover
487299-001
Power button board (includes cable)
492249-001
Keyboard (includes keyboard cable) for use with computer models in:
Brazil
486904-201
Latin America
486904-161
South Korea
486904-AD1
Taiwan
486904-AB1
Thailand
486904-281
the United States
486904-001
Top cover
487300-001
TouchPad (includes cable)
494960-001
TouchPad bracket
494962-001
TouchPad button board (includes cable)
494965-001
5
Heat sink assembly with UMA graphics subsystems (includes thermal material)
591957-001
6
Speaker assembly (includes speaker cable)
4
7
All countries and regions except India
486865-001
India
486865-D61
System board (includes replacement thermal material):
Discrete graphics subsystems
590329-001
UMA graphics subsystems
590330-001
8
Fan for models with UMA graphics subsystems
486844-001
9
Heat sink/fan with discrete graphics subsystems (includes thermal material)
591956-001
10
Modem module (select models only)
For use in all countries and regions except Australia and New Zealand
461749-001
For use in Australia and New Zealand
461749-011
Modem module cable (includes RJ-11 connector)
494981-001
Plastics Kit (see “Plastics Kit” on page 3-8 for Plastics Kit spare part information)
486862-001
11a
Hard drive cover
11b
Memory module compartment cover
11c
Mini Card compartment cover
12
USB board
486842-001
USB board cable
486843-001
13
WLAN module
(Continued)
Maintenance and Service Guide
3–3
Illustrated parts catalog
Item
Description
Spare Part Number
Atheros AR5009 802.11a/b/g/n for use in Afghanistan, Albania, Algeria, Andorra, Angola,
Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the
Bahamas, Bahrain, Barbados, Belgium, Belize, Benin, Bermuda, Bhutan, Bosnia and
Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso,
Burundi, Cambodia, Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic,
Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El
Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French
Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada,
Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong,
Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Japan,
Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia,
the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru,
Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria,
Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, the People's Republic of
China, Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Rwanda,
Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the
Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,
South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and
the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan,
Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan,
Tuvalu, Uganda, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan,
Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
518437-002
Broadcom BCM4312 802.11b/g for use in Afghanistan, Albania, Algeria, Andorra, Angola,
Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the
Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda,
Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands,
Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, the Central
African Republic, Chad, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the
Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor,
Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland,
France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece,
Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras,
Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia,
Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar,
Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania,
Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua,
Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay,
the People's Republic of China, Peru, the Philippines, Poland, Portugal, Qatar, the Republic
of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe,
Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia,
Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St.
Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and
Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab
Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,
Yemen, Zaire, Zambia, and Zimbabwe
504593-004
(Continued)
3–4
Maintenance and Service Guide
Illustrated parts catalog
Item
14
Description
Spare Part Number
Atheros AR9285 802.11b/g/n for use in Afghanistan, Albania, Algeria, Andorra, Angola,
Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the
Bahamas, Bahrain, Barbados, Belgium, Belize, Benin, Bermuda, Bhutan, Bosnia and
Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso,
Burundi, Cambodia, Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic,
Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El
Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French
Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada,
Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong,
Hungary, Iceland, India, Indonesia, Ireland, Italy, the Ivory Coast, Jamaica, Japan, Jordan,
Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia,
Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the
Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru,
Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria,
Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, the People's Republic of
China, Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Rwanda,
Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the
Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,
South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and
the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan,
Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan,
Tuvalu, Uganda, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan,
Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
518436-002
Mini Card bracket (not illustrated)
577509-001
Power connector and cable
486864-001
(Continued)
Maintenance and Service Guide
3–5
Illustrated parts catalog
Item
Description
15
Base enclosure
Computer models with a modem module
492248-001
Computer models without a modem module
487359-001
Rubber Feet Kit (not illustrated, includes six rubber feet)
486863-001
16
RTC battery (includes cable and double-sided tape)
486835-001
17
Audio board
487344-001
Audio board cable
486841-001
18
19
20
21
22
23
3–6
Spare Part Number
Hard drive (includes hard drive bracket):
500 GB, 7200 rpm
575569-001
320 GB, 7200 rpm
575568-001
250 GB, 7200 rpm
575567-001
160 GB, 7200 rpm
580846-001
Hard Drive Hardware Kit (contains screws and hard drive bracket; not illustrated)
482158-001
Optical drive (includes bezel and bracket):
DVD±R/RW SuperMulti DL Drive with LightScribe
482178-003
Blu-ray ROM DVD±R/RW SuperMulti DL Drive with LightScribe
578406-001
Memory module (PC3 1333, 1066 MHz, DDR3):
1024 MB
590351-001
2048 MB
590352-001
Processor (includes replacement thermal material):
Intel Arrandale CPU-uPGA Socket Single-Core i5-520M (2.4 GHz, 3 MB L3 cache, 1066
MHz SC Turbo)
594187-001
Intel Arrandale CPU-uPGA Socket Single-Core i5-540M (2.53 GHz, 3 MB L3 cache, 1066
MHz SC Turbo)
594188-001
Bluetooth module (select models only)
537921-001
Bluetooth module cable for discrete models
488130-001
Bluetooth module cable for UMA models
486868-001
Battery
6-cell Li-Ion (2.2 Ah, 47 Wh)
484170-001
Maintenance and Service Guide
Illustrated parts catalog
Display assembly
Item
Description
1
Display bezel
Spare part number
Models with a microphone module
487285-001
Models with a webcam/microphone module
487286-001
Display Hinge Kit
486737-001
2a
Left hinge and bracket
2b
Right hinge and bracket
3
Webcam/microphone module (select models only)
487287-001
4
14.1-in WXGA TFT BrightView display panel (includes display panel cable)
487279-001
5
Display inverter
486736-001
6
Microphone module and cable
517629-001
7
Wireless antenna transceivers and cable
8
Discrete graphics subsystems
502979-001
UMA graphics subsystems
489066-001
Display enclosure
487284-001
Display cable*
486735-001
Display Screw Kit*
486730-001
Display Rubber Kit* (includes rubber screw covers and LCD rubber pads)
487283-001
Internal display switch*
489862-001
* not illustrated
Maintenance and Service Guide
3–7
Illustrated parts catalog
Plastics Kit
Item
3–8
Description
Spare part number
Plastics Kit:
486862-001
1
Hard Drive cover (includes two captive screws)
2
Memory Module compartment cover
3
Mini Card compartment cover
Maintenance and Service Guide
Illustrated parts catalog
Mass storage devices
Item
Description
1
Hard drive (includes hard drive bracket)
2
Spare part number
500 GB, 7200 rpm
575569-001
320 GB, 7200 rpm
575568-001
250 GB, 7200 rpm
575567-001
160 GB, 7200 rpm
580846-001
Hard Drive Hardware Kit* (contains screws and hard drive bracket)
482158-001
Optical drive (includes bezel and bracket):
DVD±R/RW SuperMulti DL Drive with LightScribe
482178-003
Blu-ray ROM DVD±R/RW SuperMulti DL Drive with LightScribe
578406-001
* not illustrated
Maintenance and Service Guide
3–9
Illustrated parts catalog
Miscellaneous parts
Description
Spare part number
AC adapters
90-W PFC AC Adapter
463955-001
65-W PFC AC Adapter
463958-001
Power cords
3–10
Argentina
490371-D01
Australia
490371-011
Brazil
490371-202
India
490371-D61
Italy
490371-061
People’s Republic of China
490371-AA1
South Korea
490371-AD1
Taiwan
490371-AB1
United Kingdom and Singapore
490371-031
the United States
490371-001
Screw Kit
Phillips PM3.0 × 3.0 screws
Phillips PM2.5 × 18.0 screws
Phillips PM2.5 × 10.0 screws
Phillips PM2.5 × 7.0 captive screws
Phillips PM2.5 × 6.0 screws
Phillips PM2.5 × 5.0 captive screws
Phillips PM2.5 × 5.0 screws
Phillips PM2.5 × 4.0 screws
Phillips PM2.5 × 3.0 screws
Phillips PM2.0 × 10.0 captive screws
Phillips PM2.0 × 4.0 screws
Phillips PM2.0 × 3.0 screws
Phillips PM2.0 × 2.0 screws
487298-001
Maintenance and Service Guide
Illustrated parts catalog
Sequential part number listing
Spare part
number
Description
461749-001
Modem module for use in all countries and regions except Australia and New Zealand
461749-011
Modem module for use in Australia and New Zealand
463955-001
90-W PFC AC Adapter
463958-001
65-W PFC AC Adapter
482158-001
Hard Drive Hardware Kit (contains screws and hard drive bracket)
482178-003
DVD±R/RW SuperMulti DL Drive with LightScribe
484170-001
6-cell Li-Ion battery (2.2 Ah, 47 Wh)
486730-001
Display Screw Kit
486735-001
Display cable
486736-001
Display inverter
486737-001
Display Hinge Kit
486835-001
RTC battery (includes cable and double-sided tape)
486841-001
Audio board cable
486842-001
USB board
486843-001
USB board cable
486844-001
Fan for models with UMA graphics subsystems
486862-001
Plastics kit
486863-001
Rubber kit (includes six rubber computer feet)
486864-001
Power connector and cable
486865-001
Speaker assembly for use in all countries and regions except India
486865-D61
Speaker assembly for use in India
486868-001
Bluetooth module cable for UMA models
486904-001
Keyboard for use in the United States
486904-161
Keyboard for use in Latin America
486904-201
Keyboard for use in Brazil
486904-281
Keyboard for use in Thailand
486904-AB1
Keyboard for use in Taiwan
486904-AD1
Keyboard for use in South Korea
487279-001
14.1-in WXGA TFT BrightView display panel (includes display panel cable)
487280-001
14.1-in WXGA BrightView display with a microphone for models with discrete and UMA graphics
subsystems
487281-001
14.1-in WXGA BrightView display with a webcam/microphone for models with discrete and UMA graphics
subsystems
487283-001
Display Rubber Kit (includes rubber screw covers and LCD rubber pads)
487284-001
Display enclosure
487285-001
Display bezel for models with a microphone module
(Continued)
Maintenance and Service Guide
3–11
Illustrated parts catalog
Spare part
number
Description
487286-001
Display bezel for models with a webcam/microphone module
487287-001
Webcam/microphone module (select models only)
487298-001
Screw Kit
487299-001
Keyboard cover (includes power button board and cable)
487300-001
Top cover (includes TouchPad and cable)
487344-001
Audio board
487359-001
Base enclosure for use in computer models without a modem module
488130-001
Bluetooth module cable for discrete models
489862-001
Internal display switch
490371-001
Power cord for use in the United States
490371-011
Power cord for use in Australia
490371-031
Power cord for use in the United Kingdom and Singapore
490371-061
Power cord for use in Italy
490371-202
Power cord for use in Brazil
490371-AA1
Power cord for use in the People’s Republic of China
490371-AB1
Power cord for use in Taiwan
490371-AD1
Power cord for use in South Korea
490371-D01
Power cord for use in Argentina
490371-D61
Power cord for use in India
492248-001
Base enclosure for models with a modem module (select models only)
492249-001
Power button board (includes cable)
494960-001
TouchPad (includes cable)
494962-001
TouchPad bracket
494965-001
TouchPad button board (includes cable)
494981-001
Modem module cable (includes RJ-11 connector)
(Continued)
3–12
Maintenance and Service Guide
Illustrated parts catalog
Spare part
number
Description
504593-004
Broadcom BCM4312 802.11b/g for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and
Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina,
Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia,
Cameroon, Cape Verde, the Central African Republic, Chad, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor,
Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French
Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe,
Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India,
Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati,
Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg,
Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique,
Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria,
Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, the People's Republic of China,
Peru, the Philippines, Poland, Portugal, Qatar, the Republic of Moldova, Romania, Russia, Rwanda,
Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra
Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain,
Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia,
Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
517629-001
Microphone module and cable
518436-002
Atheros AR9285 802.11b/g/n for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and
Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Barbados,
Belgium, Belize, Benin, Bermuda, Bhutan, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin
Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, the Central African
Republic, Chad, Chile, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic,
Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador,
Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia,
Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Italy,
the Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia,
Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether
Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Palau, Panama, Papua
New Guinea, Paraguay, the People's Republic of China, Peru, the Philippines, Poland, Portugal, the
Republic of Moldova, Romania, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia,
Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands,
Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the
Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand,
Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, the United Arab
Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire,
Zambia, and Zimbabwe
(Continued)
Maintenance and Service Guide
3–13
Illustrated parts catalog
Spare part
number
3–14
Description
518437-002
Atheros AR5009 802.11a/b/g/n for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and
Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Barbados,
Belgium, Belize, Benin, Bermuda, Bhutan, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin
Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, the Central African
Republic, Chad, Chile, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic,
Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador,
Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia,
Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel,
Italy, the Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos,
Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar,
Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius,
Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the
Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Palau,
Panama, Papua New Guinea, Paraguay, the People's Republic of China, Peru, the Philippines, Poland,
Portugal, the Republic of Moldova, Romania, Rwanda, Samoa, San Marino, Sao Tome and Principe,
Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon
Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent
and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania,
Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, the United
Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire,
Zambia, and Zimbabwe
537921-001
Bluetooth module (select models only)
575567-001
250 GB, 7200 rpm hard drive (includes bracket)
575568-001
320 GB, 7200 rpm hard drive (includes bracket)
575569-001
500 GB, 7200 rpm hard drive (includes bracket)
577509-001
Mini Card bracket
578406-001
Blu-ray ROM DVD±R/RW SuperMulti DL Drive with LightScribe
580846-001
160 GB, 7200 rpm hard drive (includes bracket)
590329-001
System board for models equipped with discrete graphics subsystems
590330-001
System board for models equipped with UMA graphics subsystems
590351-001
1024 MB memory module (PC3-1333, 1066 MHz, DDR3)
590352-001
2048 MB memory module (PC3-1333, 1066 MHz, DDR3)
591956-001
Heat sink/fan for models with discrete graphics subsystems (includes thermal material)
591957-001
Heat sink assembly for models with UMA graphics subsystems (includes thermal material)
594187-001
Intel Arrandale CPU-uPGA Socket Single-Core i5-520M (2.4 GHz, 3 MB L3 cache, 1066 MHz SC Turbo)
594188-001
Intel Arrandale CPU-uPGA Socket Single-Core i5-540M (2.53 GHz, 3 MB L3 cache, 1066 MHz SC Turbo)
Maintenance and Service Guide
4
Removal and replacement procedures
Preliminary replacement requirements
Tools required
The following tools are required to complete the removal and replacement procedures:
■
Flat-bladed screwdriver
■
Magnetic screwdriver
■
Phillips P0 and P1 screwdrivers
Service considerations
The following sections include some of the considerations that you must keep in mind during disassembly and
assembly procedures.
you remove each subassembly from the computer, place the subassembly (and all accompanying screws) away
✎ As
from the work area to prevent damage.
Plastic parts
Using excessive force during disassembly and reassembly damages plastic parts. Use care when
Ä CAUTION:
handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.
Cables and connectors
When servicing the computer, be sure that cables are placed in their proper locations during the
Ä CAUTION:
reassembly process. Improper cable placement damages the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the
cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid
bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be caught or
snagged by parts being removed or replaced. Handle flex cables with extreme care; these cables tear easily.
Maintenance and Service Guide
4–1
Removal and replacement procedures
Drive handling
Drives are fragile components that must be handled with care. To prevent damage to the computer,
Ä CAUTION:
damage to a drive, or loss of information:
■
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is off
or in Hibernation, turn the computer on, and then shut it down through the operating system.
■
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive, avoid
touching the connector.
■
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and be sure
that the optical drive tray is closed.
■
Handle drives on surfaces covered with at least one inch of shock-proof foam.
■
Avoid dropping drives from any height onto any surface.
■
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
■
Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
■
Avoid exposing a drive to temperature extremes or liquids.
■
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective packaging
and label the package “FRAGILE.”
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the
degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD
contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage might have occurred.
An electronic device exposed to ESD might not be affected at all and might work perfectly throughout a normal
cycle. Or the device might function normally for a while, and then degrade in the internal layers, reducing its life
expectancy.
To prevent damage to the computer when you are removing or installing internal components:
Ä CAUTION:
■ Keep components in their electrostatic-safe containers until you are ready to install them.
4–2
■
Use nonmagnetic tools.
■
Before touching an electronic component, discharge static electricity by using the guidelines described in
this section.
■
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
■
If you remove a component, place it in an electrostatic-safe container.
Maintenance and Service Guide
Removal and replacement procedures
The following table shows how humidity affects the electrostatic voltage levels generated by different activities.
Ä CAUTION: A product can be degraded by as little as 700 V.
Relative humidity
Event
10%
40%
55%
Walking across carpet
35,000 V
15,000 V
7,500 V
Walking across vinyl floor
12,000 V
5,000 V
3,000 V
Motions of bench worker
6,000 V
800 V
400 V
Removing DIPS from plastic tube
2,000 V
700 V
400 V
Removing DIPS from vinyl tray
11,500 V
4,000 V
2,000 V
Removing DIPS from Styrofoam
14,500 V
5,000 V
3,500 V
Removing bubble pack from PCB
26,500 V
20,000 V
7,000 V
Packing PCBs in foam-lined box
21,000 V
11,000 V
5,000 V
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
■
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
■
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
■
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
■
Place items on a grounded surface before removing items from their containers.
■
Always be properly grounded when touching a component or assembly.
■
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive foam.
■
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized equipment
used for moving materials is wired to ground and that proper materials are selected to avoid static charging.
When grounding is not possible, use an ionizer to dissipate electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
■
Cover the workstation with approved static-shielding material.
■
Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and
equipment.
■
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
■
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe materials.
■
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and Styrofoam.
■
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these items
only at static-free workstations.
■
Avoid contact with pins, leads, or circuitry.
■
Shut down power and input signals before inserting or removing connectors or test equipment.
Maintenance and Service Guide
4–3
Removal and replacement procedures
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
■
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a
minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly
against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a
wrist strap.
■
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can be used at
standing workstations and are compatible with most types of shoes or boots. On conductive floors or
dissipative floor mats, use foot straps on both feet with a minimum of one megohm resistance between the
operator and ground. To be effective, the conductive strips must be worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
■
Antistatic tape
■
Antistatic smocks, aprons, and sleeve protectors
■
Conductive bins and other assembly or soldering aids
■
Nonconductive foam
■
Conductive tabletop workstations with ground cords of one megohm resistance
■
Static-dissipative tables or floor mats with hard ties to the ground
■
Field service kits
■
Static awareness labels
■
Material-handling packages
■
Nonconductive plastic bags, tubes, or boxes
■
Metal tote boxes
■
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
4–4
Material
Use
Voltage protection level
Antistatic plastic
Bags
1,500 V
Carbon-loaded plastic
Floor mats
7,500 V
Metallized laminate
Floor mats
5,000 V
Maintenance and Service Guide
Removal and replacement procedures
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 90 screws, in 13 different sizes, that must be removed, replaced, or loosened when servicing
the computer. Make special note of each screw size and location during removal and replacement.
Service tag
When ordering parts or requesting information, provide the computer serial number and model number provided on
the service tag.
Item
Component
Description
1
Product name
The name affixed to the front of the computer.
2
Serial number (s/n)
An alphanumeric identifier that is unique to each product.
3
Part number/Product number (p/n)
This number provides specific information about the product’s
hardware components. The part number helps a service
technician to determine which components and parts are needed.
4
Model description
An alphanumeric identifier used to locate documents, drivers, and
support for your computer.
5
Warranty period
The duration of the warranty period for the computer.
Maintenance and Service Guide
4–5
Removal and replacement procedures
Computer feet
The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Kit, spare part number
486863-001. There are six rubber feet that attach to the base enclosure in the locations illustrated below.
4–6
Maintenance and Service Guide
Removal and replacement procedures
Battery
Description
Spare part number
6-cell Li-Ion battery (2.2 Ah, 47 Wh)
484170-001
Before disassembling the computer:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
Remove the battery:
1. Turn the computer upside down on a flat surface, with the battery bay toward you.
2. Slide the battery release latch 1 to release the battery.
3. Pivot the battery 2 upward and lift it out of the computer 3.
To insert the battery, insert the rear edge of the battery into the battery bay and pivot the front edge downward until
the battery is seated. The battery release latch automatically locks the battery into place
Maintenance and Service Guide
4–7
Removal and replacement procedures
Hard drive
Description
Spare part number
500 GB, 7200 rpm hard drive
575569-001
320 GB, 7200 rpm hard drive
575568-001
250 GB, 7200 rpm hard drive
575567-001
160 GB, 7200 rpm hard drive
580846-001
Hard Drive Hardware Kit (includes hard drive connector, hard drive bracket, and screws)
482158-001
Before removing the hard drive:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
Remove the hard drive:
1. Position the computer with the front toward you.
2. Remove the two Phillips PM2.5×5.0 captive screws 1 that secure the hard drive cover to the computer.
3. Lift the left side 2 of the hard drive cover, swing it to the right, and remove the cover 3. The hard drive cover
is included in the Plastics Kit, spare part number 486862-001.
4–8
Maintenance and Service Guide
Removal and replacement procedures
4. Remove the two Phillips PM2.0×4.0 screws 1 that secure the hard drive to the computer.
5. Use the Mylar tab 2 on the hard drive to slide the hard drive 3 to the left.
6. Remove the hard drive 4 from the hard drive bay.
7. If it is necessary to replace the hard drive bracket
a. Remove the two Phillips PM3.0×3.0 screws 1 from each side of the hard drive.
b. Lift the bracket 2 straight up to remove it from the hard drive.
Reverse this procedure to reassemble and install the hard drive.
Maintenance and Service Guide
4–9
Removal and replacement procedures
Memory module
Description
Spare part number
1024 MB (PC3-1333, 1066 MHz, DDR3)
590351-001
2048 MB (PC3-1333, 1066 MHz, DDR3)
590352-001
Before removing the memory module:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the hard drive cover (see “Hard drive” on page 4-8).
Remove the memory module:
✎ The top memory module slot is for expansion memory and the bottom slot is for primary memory.
1. Position the computer with the front toward you.
2. Remove the Phillips PM2.5×7.0 captive screw 1 that secures the memory module compartment cover to the
computer.
3. Lift the right side of the cover 2, swing it to the left, and lift the cover off the computer 3. The memory
module compartment cover is included in the Plastics Kit, spare part number 486862-001.
4–10
Maintenance and Service Guide
Removal and replacement procedures
4. Spread the retaining tabs 1 on each side of the memory module to release the memory module. (The edge of
the module opposite the slot rises away from the computer.)
5. Remove the memory module 2 by pulling the module away from the slot at an angle.
modules are designed with a notch 3 to prevent incorrect insertion into the memory
✎ Memory
module slot.
Reverse this procedure to install a memory module.
Maintenance and Service Guide
4–11
Removal and replacement procedures
RTC battery
Description
Spare part number
RTC battery (includes cable and double-sided tape)
486835-001
Before removing the RTC battery:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
Remove the RTC battery:
1. Remove the two Phillips PM2.5×5.0 captive screws 1 that secure the Mini Card compartment cover to the
computer.
2. Lift the right side of the Mini Card compartment cover 2, swing it to the left, and remove the cover 3. The
Mini Card compartment cover is included in the Plastics Kit, spare part number 486862-001.
4–12
Maintenance and Service Guide
Removal and replacement procedures
3. Disconnect the RTC battery cable 1 from the system board.
4. Release the two-sided tape 2 that holds the RTC battery.
5. Remove the RTC battery 3.
Reverse this procedure to install the RTC battery.
Maintenance and Service Guide
4–13
Removal and replacement procedures
WLAN module
Description
Spare part number
Atheros AR5009 802.11a/b/g/n for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua
and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Barbados, Belgium, Belize, Benin, Bermuda, Bhutan, Bosnia and Herzegovina, Botswana, Brazil,
the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape
Verde, the Central African Republic, Chad, Chile, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East
Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland,
France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada,
Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary,
Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Japan, Jordan,
Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia,
Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives,
Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco,
Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the
Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Palau, Panama, Papua New
Guinea, Paraguay, the People's Republic of China, Peru, the Philippines, Poland, Portugal, the
Republic of Moldova, Romania, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi
Arabia, Senegal, Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon
Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St.
Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan,
Tanzania, Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu,
Uganda, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela,
Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
518437-002
Broadcom BCM4312 802.11b/g for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua
and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and
Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi,
Cambodia, Cameroon, Cape Verde, the Central African Republic, Chad, Colombia, Comoros, the
Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the
Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana,
Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti,
Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast,
Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the
Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan,
Palau, Panama, Papua New Guinea, Paraguay, the People's Republic of China, Peru, the
Philippines, Poland, Portugal, Qatar, the Republic of Moldova, Romania, Russia, Rwanda, Samoa,
San Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia, the Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri
Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland,
Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga, Trinidad and
Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the
United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and
Zimbabwe
504593-004
(Continued)
4–14
Maintenance and Service Guide
Removal and replacement procedures
Description
Spare part number
Atheros AR9285 802.11b/g/n for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and
Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Barbados, Belgium, Belize, Benin, Bermuda, Bhutan, Bosnia and Herzegovina, Botswana, Brazil,
the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape
Verde, the Central African Republic, Chad, Chile, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East
Timor, Ecuador, Egypt, El Salvador, Equatorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland,
France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada,
Guadeloupe, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary,
Iceland, India, Indonesia, Ireland, Italy, the Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan,
Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein,
Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the
Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia,
Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands,
New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Palau, Panama, Papua New Guinea,
Paraguay, the People's Republic of China, Peru, the Philippines, Poland, Portugal, the Republic of
Moldova, Romania, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal,
Serbia, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,
South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the
Grenadines, Suriname, Swaziland, Sweden, Switzerland, Syria, Taiwan, Tajikistan, Tanzania,
Thailand, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, the
United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,
Yemen, Zaire, Zambia, and Zimbabwe
518436-002
Mini Card bracket
577509-001
Maintenance and Service Guide
4–15
Removal and replacement procedures
Before removing the WLAN module:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
Remove the WLAN module (for models with discrete graphics subsystems):
To prevent an unresponsive system, replace the wireless module only with a wireless module authorized
Ä CAUTION:
for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you
replace the module and then receive a warning message, remove the module to restore computer functionality, and
then contact technical support through Help and Support.
1. Remove the RTC battery (see “RTC battery” on page 4-12).
2. Position the computer with the front toward you.
3. Disconnect the WLAN antenna cables 1 from the terminals on the WLAN module.
black WLAN antenna cable is connected to the WLAN module “Main” terminal. The white WLAN
✎ The
antenna cable is connected to the WLAN module “Aux” terminal.
4. Remove the two Phillips PM2.0×4.0 screws 2 that secure the WLAN module to the computer. (The edge of the
module opposite the slot rises away from the computer.)
5. Remove the WLAN module 3 by pulling the module away from the slot at an angle.
WLAN modules are designed with a notch 4 to prevent incorrect insertion of the WLAN module into
✎ the
WLAN module slot.
4–16
Maintenance and Service Guide
Removal and replacement procedures
6. If it is necessary to replace the Mini Card bracket, remove the two Phillips PM2.5×4.0 screws 1?that secure it
to the base enclosure.
7. Lift the bracket 2 straight up to remove it.
Reverse this procedure to install the WLAN module.
Maintenance and Service Guide
4–17
Removal and replacement procedures
Remove the WLAN module (for models with UMA graphics subsystems):
To prevent an unresponsive system, replace the wireless module only with a wireless module authorized
Ä CAUTION:
for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you
replace the module and then receive a warning message, remove the module to restore computer functionality, and
then contact technical support through Help and Support.
1. Remove the hard drive cover (see “Hard drive” on page 4-8).
2. Position the computer with the front toward you.
3. Disconnect the WLAN antenna cables 1 from the terminals on the WLAN module.
black WLAN antenna cable is connected to the WLAN module “Main” terminal. The white WLAN
✎ The
antenna cable is connected to the WLAN module “Aux” terminal.
4. Remove the two Phillips PM2.0×4.0 screws 2 that secure the WLAN module to the computer. (The edge of the
module opposite the slot rises away from the computer.)
5. Remove the WLAN module 3 by pulling the module away from the slot at an angle.
WLAN modules are designed with a notch 4 to prevent incorrect insertion of the WLAN module into
✎ the
WLAN module slot.
4–18
Maintenance and Service Guide
Removal and replacement procedures
6. To replace the Mini Card bracket, remove the two Phillips PM2.5×4.0 screws 1?that secure it to the base
enclosure.
7. Lift the bracket 2 straight up to remove it.
Reverse this procedure to install the WLAN module.
Maintenance and Service Guide
4–19
Removal and replacement procedures
Optical drive
✎ The optical drive spare part kit includes an optical drive bezel and bracket.
Description
Spare part number
Blu-ray ROM DVD±R/RW SuperMulti DL Drive with LightScribe
578406-001
DVD±R/RW SuperMulti DL Drive with LightScribe
482178-001
Before removing the optical drive:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
Remove the optical drive:
1. Position the computer with the right side toward you.
2. Remove the Phillips PM2.5×5.0 screw 1 that secures the optical drive to the computer.
3. Insert a thin tool, such as a paper clip 2, into the release access and press to release the drive. (The optical drive
disc tray is partially ejected from the optical drive.)
4. Use the disc tray frame to slide the optical drive 3 out of the computer.
Reverse this procedure to reassemble and install an optical drive.
4–20
Maintenance and Service Guide
Removal and replacement procedures
Keyboard
Description
Spare part number
Brazil
486904-201
Latin America
486904-161
South Korea
486904-AD1
Taiwan
486904-AB1
Thailand
486904-281
the United States
486904-001
Before removing the keyboard:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the hard drive cover (see “Hard drive” on page 4-8).
6. Remove the Mini Card compartment cover (see “RTC battery” on page 4-12).
7. Remove the optical drive (see “Optical drive” on page 4-20).
Remove the keyboard:
1. Remove the three Phillips PM2.5×17.0 screws that secure the keyboard to the computer.
Maintenance and Service Guide
4–21
Removal and replacement procedures
2. Turn the computer display-side up with the front toward you.
3. Open the computer as far as possible.
4. Lift the rear edge 1 of the keyboard until it rests at an angle.
✎ The keyboard is held by two-sided tape.
5. Slide the keyboard 2 back until the tabs on the bottom of the keyboard are clear of the keyboard cover.
6. Release the zero insertion force (ZIF) connector 1 to which the keyboard cable is attached, and thendisconnect
the keyboard cable 2 from the system board.
7. Remove the keyboard.
Reverse this procedure to install the keyboard.
4–22
Maintenance and Service Guide
Removal and replacement procedures
Keyboard cover
Description
Spare part number
Keyboard cover (includes power button board and cable)
487299-001
Before removing the keyboard cover:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive cover (see “Hard drive” on page 4-8)
b. Mini Card compartment cover (see “RTC battery” on page 4-12)
c. Optical drive (see “Optical drive” on page 4-20)
d. Keyboard (see “Keyboard” on page 4-21)
Remove the keyboard cover:
1. Remove the Phillips PM2.0×3.0 broadhead screw 1 from the optical drive bay, the Phillips PM2.5×5.0
screw 2 from the hard drive bay, and four Phillips PM2.0×3.0 screws 3 from the battery bay.
2. From the base enclosure rear corners, remove the two Phillips PM2.5×10.0 screws 4 that secure the keyboard
cover to the computer.
Maintenance and Service Guide
4–23
Removal and replacement procedures
3. Turn the computer display-side up, with the front toward you.
4. Open the computer as far as possible.
5. Remove the Phillips PM2.5×6.0 screw 1 from the front left corner of the keyboard cover.
6. Release the ZIF connector to which the power button board cable 2 is connected and disconnect the cable from
the system board.
7. Lift and remove the keyboard cover 3 from the computer.
Reverse this procedure to install the keyboard cover.
4–24
Maintenance and Service Guide
Removal and replacement procedures
Speaker assembly
Description
Spare part number
All countries and regions except India
486865-001
India
486865-D61
Before removing the speaker assembly:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive cover (see “Hard drive” on page 4-8)
b. Mini Card compartment cover (see “RTC battery” on page 4-12)
c. Optical drive cover (see “Optical drive” on page 4-20)
d. Keyboard (see “Keyboard” on page 4-21)
e. Keyboard cover (see “Keyboard cover” on page 4-23)
Remove the speaker assembly:
1. Disconnect the speaker cable 1 from the system board.
2. Release the zero insertion force (ZIF) connector for the num lock cable 2 from the system board.
Maintenance and Service Guide
4–25
Removal and replacement procedures
3. Remove the two Phillips PM2.5×3.0 screws 1 that secure the speaker assembly to the computer.
4. Lift the speaker assembly 2 straight up to remove it from the computer.
Reverse this procedure to install the speaker assembly.
4–26
Maintenance and Service Guide
Removal and replacement procedures
Display assembly
display assembly spare part kit includes two WLAN antenna transceivers and cables, webcam (select models
✎ The
only), microphone, nameplate, and logo.
Description
Spare part number
14.1-in WXGA BrightView display with a microphone for models with discrete and UMA graphics
subsystems
580763-001
14.1-in WXGA BrightView display with a webcam/microphone for models with discrete and UMA
graphics subsystems
580766-001
Before removing the display assembly:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Disconnect the wireless antenna cables from the WLAN module (see “WLAN module” on page 4-14).
6. Remove the following components:
a. Hard drive cover (see “Hard drive” on page 4-8)
b. Mini Card compartment cover (see “RTC battery” on page 4-12)
c. Optical drive (see “Optical drive” on page 4-20
d. Keyboard (see “Keyboard” on page 4-21)
e. Keyboard cover (see “Keyboard cover” on page 4-23)
f. Speaker assembly (see “Speaker assembly” on page 4-25)
Maintenance and Service Guide
4–27
Removal and replacement procedures
Remove the display assembly:
1. Turn the computer display-side up, with the front toward you.
2. Open the computer as far as possible.
3. Remove the wireless antenna cable 1 from the hole in the system board and the routing channels and clips
built into the top cover.
models with UMA graphics subsystems, the antenna cable routes to the hard drive bay. For models with
✎ For
discrete graphics subsystems, the antenna cable routes to the Mini Card compartment.
4. Disconnect the display panel cable 2 from the system board.
5. Remove the microphone cable 1 from the hole in the system board and the routing channels and clips built into
the top cover.
6. Disconnect the microphone cable from the system board 2.
Support the display assembly when removing the following screws. Failure to support the display
Ä CAUTION:
assembly can result in damage to the display assembly and other computer components.
4–28
Maintenance and Service Guide
Removal and replacement procedures
7. Remove the four Phillips PM2.5×6.0 screws 1 that secure the display assembly to the computer.
8. Remove the display assembly 2.
9. To replace the display bezel or any of the display assembly internal components, remove the Mylar screw
covers 1 and the two Phillips PM2.5×5.0 screws 2 on the display bezel lower edge.The display rubber screw
covers are included in the Display Rubber Kit, spare part number 487283-001.
Maintenance and Service Guide
4–29
Removal and replacement procedures
10. Flex the inside edges of the top edge 1, the left and right sides 2, and the bottom edge of the display bezel
3 until the bezel disengages from the display enclosure.
11. Remove the display bezel 4. The display bezel without a webcam module is available using spare part number
487285-001. The display bezel with a webcam module is available using 487286-001.
12. To replace the display inverter, lift the inverter 1 from the clips in the display enclosure as far as the display
panel cable and the backlight cable will allow.
13. Disconnect the display panel cable 2 and the backlight cable 3 from the display inverter. The display inverter
is available using spare part number 486736-001.
4–30
Maintenance and Service Guide
Removal and replacement procedures
14. To replace the display panel, remove the six Phillips PM2.5×5.0 screws 1 that secure the display panel to the
display enclosure.
15. Remove the display panel 2. The display panel is available using the spare part number 487279-001.
16. To replace the display cable:
a. Peel back the plastic 1 that covers the cable.
b. Remove the tape 2 that secures the cable to the display.
c. Unplug the cable 3 from the display.
d. Remove the cable from the display 4. The display cable is available using spare part number 486735-001.
Maintenance and Service Guide
4–31
Removal and replacement procedures
17. To replace the display hinges, remove the four Phillips PM2.0×3.0 screws 1 that secure each hinge to the
display panel.
✎ Remove and install the screws in the sequence indicated on the display hinge bracket.
18. Remove the display hinges 2. The Display Hinge Kit is available using spare part number 486737-001.
19. To replace the wireless antenna transceivers and cables, remove the Phillips PM2.5×3.0 screw 1 that secures
each transceiver to the display enclosure.
20. Detach the wireless antenna transceivers 2 from the display enclosure. The transceivers are secured by a foil
wrapping.
21. Release the wireless antenna transceivers and cables from the clips 3 built into the display enclosure.
22. Remove the wireless antenna transceivers and cables 4 from the display enclosure. The wireless antenna
transceivers and cables are available using spare part number 502979-001 for models with discrete graphics
subsystems, and spare part number 489066-001 for models with UMA graphics subsystems.
Reverse this procedure to reassemble and install the display assembly.
4–32
Maintenance and Service Guide
Removal and replacement procedures
Webcam/microphone module (select models only)
Description
Spare part number
Webcam/microphone module
487287-001
Before removing the display assembly:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Disconnect the wireless antenna cables from the WLAN module (see “WLAN module” on page 4-14).
6. Remove the following components:
a. Hard drive cover (see “Hard drive” on page 4-8)
b. Mini Card compartment cover (see “RTC battery” on page 4-12)
c. Optical drive (see “Optical drive” on page 4-20
d. Keyboard (see “Keyboard” on page 4-21)
e. Keyboard cover (see “Keyboard cover” on page 4-23)
f. Speaker assembly (see “Speaker assembly” on page 4-25)
g. Display assembly (see “Display assembly” on page 4-27)
Remove the webcam/microphone module:
1. Lift the webcam/microphone module 1 as far from the display enclosure as the webcam/microphone module
cable allows.
2. Disconnect the webcam/microphone module cable 2 from the webcam/microphone module.
3. Remove the webcam/microphone module.
Reverse this procedure to install the webcam/microphone module.
Maintenance and Service Guide
4–33
Removal and replacement procedures
Microphone module
Description
Spare part number
Microphone module (includes cable)
517629-001
Before removing the display assembly:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Disconnect the wireless antenna cables from the WLAN module (see “WLAN module” on page 4-14).
6. Remove the following components:
a. Hard drive cover (see “Hard drive” on page 4-8)
b. Mini Card compartment cover (see “RTC battery” on page 4-12)
c. Optical drive (see “Optical drive” on page 4-20
d. Keyboard (see “Keyboard” on page 4-21)
e. Keyboard cover (see “Keyboard cover” on page 4-23)
f. Speaker assembly (see “Speaker assembly” on page 4-25)
g. Display assembly (see “Display assembly” on page 4-27)
Remove the microphone module:
1. Release the tabs 1 built into the display enclosure.
2. Release the microphone receiver 2 from the display enclosure. The microphone receiver is secured by
two-sided tape.
3. Remove the microphone cable 3 and receiver from the display enclosure.
Reverse this procedure to install the microphone module.
4–34
Maintenance and Service Guide
Removal and replacement procedures
Top cover
Description
Spare part number
Top cover
487300-001
TouchPad (includs cables)
494960-001
TouchPad bracket
494962-001
TouchPad button board (includes cables)
494965-001
Before removing the top cover:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Mini Card compartment cover (see “RTC battery” on page 4-12)
c. Mini Card bracket (see “WLAN module” on page 4-14
d. Optical drive (see “Optical drive” on page 4-20)
e. Keyboard (see “Keyboard” on page 4-21)
f. Switch cover (see “Keyboard cover” on page 4-23)
g. Speaker assembly (see “Speaker assembly” on page 4-25)
h. Display assembly (see “Display assembly” on page 4-27)
Maintenance and Service Guide
4–35
Removal and replacement procedures
Remove the top cover:
1. Turn the computer upside down with the front toward you.
2. Remove the following screws that secure the top cover to the base enclosure:
1 Three Phillips PM2.5×10.0 screws
2 Two Phillips PM2.5×5.0 screws
3 Two Phillips PM2.0×3.0 screws
3. Turn the computer right-side up, with the front toward you.
4. Disconnect the following cables from the system board:
1 TouchPad cable with zero insertion force (ZIF) connector
2 USB cable
5. Remove the two Phillips PM2.5×6.0 screws 1 that secure the top cover to the base enclosure.
6. Lift up the front edge of the top cover until it releases from the base 2.
7. Remove the top cover 3.
4–36
Maintenance and Service Guide
Removal and replacement procedures
Reverse this procedure to install the top cover.
Maintenance and Service Guide
4–37
Removal and replacement procedures
Bluetooth module and cable (select models only)
Description
Spare part number
Bluetooth module
537921-001
Bluetooth module cable for discrete models
488130-001
Bluetooth module cable for UMA models
486868-001
Before removing the Bluetooth module:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Mini Card compartment cover (see “RTC battery” on page 4-12)
c. Mini Card bracket (see “WLAN module” on page 4-14)
d. Optical drive (see “Optical drive” on page 4-20)
e. Keyboard (see “Keyboard” on page 4-21)
f. Keyboard cover (see “Keyboard cover” on page 4-23)
g. Speaker assembly (see “Speaker assembly” on page 4-25)
h. Display assembly (see “Display assembly” on page 4-27)
i. Top cover (see “Top cover” on page 4-35)
4–38
Maintenance and Service Guide
Removal and replacement procedures
Remove the Bluetooth module and cable:
1. Turn the top cover upside down with the front toward you.
2. Lift the Bluetooth module 1 away from computer.
3. Disconnect the Bluetooth module cable 2 from the system board and Bluetooth module.
4. Release the tape 3 that secures cable.
5. Remove Bluetooth module and cable 4.
Reverse this procedure to install the Bluetooth module and cable.
Maintenance and Service Guide
4–39
Removal and replacement procedures
Modem module
Description
Spare part number
All countries and regions except Australia and New Zealand
461749-001
Australia and New Zealand
461749-011
Before removing the modem module:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
6.
a. Hard drive (see “Hard drive” on page 4-8)
b. Mini Card compartment cover (see “RTC battery” on page 4-12)
c. Mini Card bracket (see “WLAN module” on page 4-14)
d. Optical drive (see “Optical drive” on page 4-20)
e. Keyboard (see “Keyboard” on page 4-21)
f. Keyboard cover (see “Keyboard cover” on page 4-23)
g. Speaker assembly (see “Speaker assembly” on page 4-25)
h. Display assembly (see “Display assembly” on page 4-27)
i. Top cover (see “Top cover” on page 4-35)
4–40
Maintenance and Service Guide
Removal and replacement procedures
Remove the modem module:
1. Turn the computer right-side up, with the front toward you.
2. Remove the two Phillips PM2.0×4.0 screws 1 that secure the modem module to the system board.
3. Disconnect the modem module cable 2 from the modem module.
4. Lift up on the front of the modem module 3 to disconnect it from the system board.
Reverse this procedure to install the modem module.
replacing the modem module, be sure that the connector on the bottom of the modem module connects
✎ When
firmly to the system board.
Maintenance and Service Guide
4–41
Removal and replacement procedures
Audio board
Description
Spare part number
Audio board
487344-001
Audio board cable
486841-001
Before removing the audio board:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Mini Card compartment cover (see “RTC battery” on page 4-12)
c. Mini Card bracket (see “WLAN module” on page 4-14)
d. Optical drive (see “Optical drive” on page 4-20)
e. Keyboard (see “Keyboard” on page 4-21)
f. Keyboard cover (see “Keyboard cover” on page 4-23)
g. Speaker assembly (see “Speaker assembly” on page 4-25)
h. Display assembly (see “Display assembly” on page 4-27)
i. Top cover (see “Top cover” on page 4-35)
4–42
Maintenance and Service Guide
Removal and replacement procedures
Remove the audio board and cable:
1. Disconnect the audio board cable 1 from the system board.
2. Remove the cable from between the components that secure it in the base 2.
3. Remove the two Phillips PM2.5×3.0 screws 3 that secures the audio board to the system board.
4. Lift the rear edge of the audio board 4 so that the audio connectors slide out of the openings in the base
enclosure and remove the audio board and cable.
Reverse this procedure to install the audio board.
Maintenance and Service Guide
4–43
Removal and replacement procedures
USB board
Description
Spare part number
USB board
486842-001
USB board cable
486843-001
Before removing the USB board:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Mini Card compartment cover (see “RTC battery” on page 4-12)
c. Mini Card bracket (see “WLAN module” on page 4-14)
d. Optical drive (see “Optical drive” on page 4-20)
e. Keyboard (see “Keyboard” on page 4-21)
f. Keyboard cover (see “Keyboard cover” on page 4-23)
g. Speaker assembly (see “Speaker assembly” on page 4-25)
h. Display assembly (see “Display assembly” on page 4-27)
i. Top cover (see “Top cover” on page 4-35)
4–44
Maintenance and Service Guide
Removal and replacement procedures
Remove the USB board and cable:
1. Turn the computer display-side up, with the right side toward you.
2. Disconnect the USB board cable 1 from the system board.
3. Remove the cable 2 from the base enclosure clips.
4. Remove the Phillips PM2.5×3.0 screw 3 that secures the USB board to the computer.
5. Lift the USB board 4 straight up to remove it from the computer.
Reverse this procedure to install the USB board.
Maintenance and Service Guide
4–45
Removal and replacement procedures
Power connector and cable
Description
Spare part number
Power connector and cable
486864-001
Before removing the power connector and cable:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Mini Card compartment cover (see “RTC battery” on page 4-12)
c. Mini Card bracket (see “WLAN module” on page 4-14)
d. Optical drive (see “Optical drive” on page 4-20)
e. Keyboard (see “Keyboard” on page 4-21)
f. Keyboard cover (see “Keyboard cover” on page 4-23)
g. Speaker assembly (see “Speaker assembly” on page 4-25)
h. Display assembly (see “Display assembly” on page 4-27)
i. Top cover (see “Top cover” on page 4-35)
4–46
Maintenance and Service Guide
Removal and replacement procedures
Remove the power connector and cable:
1. Turn the computer right-side up.
2. Position the computer with the right side toward you.
3. Disconnect the power connector cable 1 from the bottom of the system board.
4. Remove the power connector 2 from the clip built into the base enclosure. The power connector is secured by
two-sided tape.
Reverse this procedure to install the power connector and cable.
Maintenance and Service Guide
4–47
Removal and replacement procedures
System board
✎ The system board spare part kit includes replacement thermal material.
Description
Spare part number
Discrete graphics subsystems
590329-001
UMA graphics subsystems
590330-001
Before removing the system board:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. RTC battery (see “RTC battery” on page 4-12)
d. WLAN module (see “WLAN module” on page 4-14)
e. Optical drive (see “Optical drive” on page 4-20)
f. Keyboard (see “Keyboard” on page 4-21)
g. Keyboard cover (see “Keyboard cover” on page 4-23)
h. Speaker assembly (see “Speaker assembly” on page 4-25)
i. Display assembly (see “Display assembly” on page 4-27)
j. Top cover (see “Top cover” on page 4-35)
4–48
Maintenance and Service Guide
Removal and replacement procedures
When replacing the system board, be sure that the following additional components are removed from the defective
system board and installed on the replacement system board:
■
Fan/heat sink assembly (see “Heat sink/fan assembly or heat sink” on page 4-52)
■
Processor (see “Processor” on page 4-57)
Remove the system board:
1. Turn the computer display-side up.
2. Position the computer with the right side toward you.
3. Disconnect the following cables from the system board:
1 Modem cable
2 Audio board cable
3 USB board cable
4 Fan cable
Maintenance and Service Guide
4–49
Removal and replacement procedures
4. Disconnect the power connector cable.
5. Remove the two Phillips PM2.5×5.0 screws that secure the system board to the base enclosure.
4–50
Maintenance and Service Guide
Removal and replacement procedures
6. Lift the right side 1 of the system board until it rests at an angle 2.
7. Remove the system board by sliding it to the right at an angle 3 until the connectors on the left side of the
system board disengage from the base enclosure.
8. To replace the RJ-11 connector and cable, remove the RJ-11 connector 1 from the clip built into the base
enclosure.
9. Remove the cable 2 from the routing channel built into the base enclosure. The RJ-II connector and cable are
available using spare part number 494981-001.
Reverse this procedure to install the system board.
Maintenance and Service Guide
4–51
Removal and replacement procedures
Heat sink/fan assembly or heat sink
Description
Spare part number
Heat sink/fan assembly for models with discrete graphics subsystems (includes thermal material)
591956-001
Heat sink for models with UMA graphics subsystems (includes thermal material)
591957-001
properly ventilate the computer, allow at least a 7.6 cm (3 in) clearance on the left side of the computer. The
✎ Tocomputer
uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to
turn on automatically when high temperature conditions exist. These conditions are affected by high external
temperatures, system power consumption, power management/battery conservation configurations, battery fast
charging, and software requirements. Exhaust air is displaced through the ventilation grill located on the left side
of the computer.
Before removing the heat sink (for models with UMA graphics subsystems) or the heat sink/fan assembly (for
models with discrete graphics subsystems):
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. RTC battery (see “RTC battery” on page 4-12)
d. WLAN module (see “WLAN module” on page 4-14)
e. Optical drive (see “Optical drive” on page 4-20)
f. Keyboard (see “Keyboard” on page 4-21)
g. Keyboard cover (see “Keyboard cover” on page 4-23)
h. Speaker assembly (see “Speaker assembly” on page 4-25)
i. Display assembly (see “Display assembly” on page 4-27)
j. Top cover (see “Top cover” on page 4-35)
k. System board (see “System board” on page 4-48)
4–52
Maintenance and Service Guide
Removal and replacement procedures
Remove the fan/heat sink:
1. Turn the system board upside down, with the front toward you.
two through four apply to computer models equipped with graphics subsystems with discrete memory. Steps
✎ Steps
five and six apply to computer models equipped with graphics subsystems with UMA memory.
2. Disconnect the fan cable 1.
3. Loosen the four captive Phillips PM2.0×10.0 screws 2 that secure the fan/heat sink assembly to the
system board.
4. Remove the fan/heat sink assembly 3.
Due to the adhesive quality of the thermal material located between the fan/heat sink assembly and
✎ system
board components, it might be necessary to move the fan/heat sink assembly from side to side to
detach the assembly.
Maintenance and Service Guide
4–53
Removal and replacement procedures
thermal material must be thoroughly cleaned from the surface of the fan/heat sink assembly and the system
✎ The
board each time the heat sink assembly is removed. Thermal material is applied to the discrete fan/heat sink to
correspond with components on the system board as follows: the processor 1, the Northbridge chip 2, the ATI
video chip 3, and the capacitors 4. Replacement thermal material is included with all system board, fan/heat sink
assembly, and processor spare parts.
two through four apply to computer models equipped with graphics subsystems with discrete memory.
✎ Steps
Steps five and six apply to computer models equipped with graphics subsystems with UMA memory.
5. Loosen the four captive Phillips PM2.0×10.0 screws 1 that secure the heat sink assembly to the system board.
6. Remove the heat sink assembly 2.
Due to the adhesive quality of the thermal material located between the fan/heat sink assembly and
✎ system
board components, it might be necessary to move the fan/heat sink assembly from side to side to
detach the assembly.
4–54
Maintenance and Service Guide
Removal and replacement procedures
thermal material must be thoroughly cleaned from the surface of the heat sink assembly and the system board
✎ The
each time the heat sink assembly is removed. Thermal material is applied to the heat sink to correspond with
components on the system board as follows: the processor 1, the Northbridge chip 2, and the capacitors 3.
Replacement thermal material is included with all system board, fan/heat sink assembly, and processor spare parts.
Reverse this procedure to install the fan/heat sink assembly.
Maintenance and Service Guide
4–55
Removal and replacement procedures
Fan (for models with UMA graphics subsystems)
Description
Spare part number
Fan
486844-001
Before removing the fan:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. RTC battery (see “RTC battery” on page 4-12)
d. WLAN module (see “WLAN module” on page 4-14)
e. Optical drive (see “Optical drive” on page 4-20)
f. Keyboard (see “Keyboard” on page 4-21)
g. Keyboard cover (see “Keyboard cover” on page 4-23)
h. Speaker assembly (see “Speaker assembly” on page 4-25)
i. Display assembly (see “Display assembly” on page 4-27)
j. Top cover (see “Top cover” on page 4-35)
k. System board (see “System board” on page 4-48)
Remove the fan:
1. Position the base enclosure with the front toward you.
2. Remove the two black Phillips PM2.5×5.0 screws 1 that secure the fan to the computer.
3. Lift the fan from the base enclosure 2.
Reverse this procedure to install the fan.
4–56
Maintenance and Service Guide
Removal and replacement procedures
Processor
✎ The processor spare part kit includes replacement thermal material.
Description
Spare part number
Intel Arrandale CPU-uPGA Socket Single-Core i5-520M (2.4 GHz, 3 MB L3 cache, 1066 MHz SC
Turbo)
594187-001
Intel Arrandale CPU-uPGA Socket Single-Core i5-540M (2.53 GHz, 3 MB L3 cache, 1066 MHz SC
Turbo)
594188-001
Before removing the processor:
1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on,
and then shut it down through the operating system.
2. Disconnect all external devices connected to the computer.
3. Disconnect the power from the computer by first disconnecting the power cord from the AC outlet and then
disconnecting the AC adapter from the computer.
4. Remove the battery (see “Battery” on page 4-7).
5. Remove the following components:
a. Hard drive (see “Hard drive” on page 4-8)
b. Memory module (see “Memory module” on page 4-10)
c. RTC battery (see “RTC battery” on page 4-12)
d. WLAN module (see “WLAN module” on page 4-14)
e. Optical drive (see “Optical drive” on page 4-20)
f. Keyboard (see “Keyboard” on page 4-21)
g. Keyboard cover (see “Keyboard cover” on page 4-23)
h. Speaker assembly (see “Speaker assembly” on page 4-25)
i. Display assembly (see “Display assembly” on page 4-27)
j. Top cover (see “Top cover” on page 4-35)
k. System board (see “System board” on page 4-48)
l. Fan/heat sink assembly (see “Heat sink/fan assembly or heat sink” on page 4-52)
Maintenance and Service Guide
4–57
Removal and replacement procedures
Remove the processor:
1. Use a flat-bladed screwdriver to turn the processor locking screw 1 one half-turn counterclockwise until you
hear a click.
2. Lift the processor 2 straight up to remove it.
installing the processor, align the gold triangle 3 on the processor with the triangle 4 embossed
✎ When
on the processor socket.
Reverse this procedure to install the processor.
4–58
Maintenance and Service Guide
5
Setup Utility
Starting Setup Utility
Setup Utility is a ROM-based information and customization utility that can be used even when your Windows
operating system is not working.
The utility reports information about the computer and provides settings for startup, security, and other preferences.
To start Setup Utility:
»
Open Setup Utility by turning on or restarting the computer. When the Press the ESC key for Startup Menu
message appears in the lower left corner of the screen, press the f10 key.
– or –
1. Open Setup Utility by turning on or restarting the computer. When the Press the ESC key for Startup Menu
message appears in the lower left corner of the screen, press the esc key.
2. When the Startup Menu appears, press the f10 key.
Using Setup Utility
Changing the language of Setup Utility
The following procedure explains how to change the language of Setup Utility. If Setup Utility is not already
running, begin at step 1. If Setup Utility is already running, begin at step 2.
1. Open Setup Utility by turning on or restarting the computer. When the Press the ESC key for Startup Menu
message appears in the lower left corner of the screen, press the f10 key.
– or –
Open Setup Utility by turning on or restarting the computer. When the Press the ESC key for Startup Menu
message appears in the lower left corner of the screen, press the esc key. When the Startup Menu appears, press
the f10 key.
2. Use the arrow keys to select System Configuration > Language, and then press the enter key.
3. Use the arrow keys to select a language, and then press the enter key.
4. When a confirmation prompt with your language selected is displayed, press the enter key.
5. To save your change and exit Setup Utility, use the arrow keys to select Exit > Exit Saving Changes, and then
press the enter key.
Changes go into effect immediately.
Maintenance and Service Guide
5–1
Setup Utility
Navigating and selecting in Setup Utility
Because Setup Utility is not Windows based, it does not support the TouchPad. Navigation and selection are
by keystroke.
■ To choose a menu or a menu item, use the arrow keys.
■ To choose an item in a list or to toggle a field, for example an Enable/Disable field, use either the arrow keys or
press the f5 or f6 key.
■ To select an item, press the enter key.
■ To close a text box or return to the menu display, press the esc key.
■ To display additional navigation and selection information while Setup Utility is open, press the f1 key.
Displaying system information
Use Setup Utility to view such information as the system time and date and information that identifies the
computer. The following procedure explains how to do this. If Setup Utility is not open, begin at step 1. If Setup
Utility is open, begin at step 2.
1. Open Setup Utility by turning on or restarting the computer. When the Press the ESC key for Startup Menu
message appears in the lower left corner of the screen, press the f10 key.
– or –
Open Setup Utility by turning on or restarting the computer. When the Press the ESC key for Startup Menu
message appears in the lower left corner of the screen, press the esc key. When the Startup Menu is displayed,
press the f10 key.
2. Select the Main menu.
3. To exit Setup Utility without changing any settings, use the arrow keys to select Exit > Exit Discarding
Changes, and then press the enter key.
Restoring default settings in Setup Utility
The following procedure explains how to restore Setup Utility default settings. If Setup Utility is not already
running, begin at step 1. If Setup Utility is already running, begin at step 2.
1. Open Setup Utility by turning on or restarting the computer. When the Press the ESC key for Startup Menu
message appears in the lower left corner of the screen, press the f10 key.
– or –
Open Setup Utility by turning on or restarting the computer. When the Press the ESC key for Startup Menu
message appears in the lower left corner of the screen, press the esc key. When the Startup Menu appears, press
the f10 key.
2. Use the arrow keys to select Exit > Load Setup Defaults, and then press the enter key.
3. When the Setup Confirmation appears, press the enter key.
4. To save your change and exit Setup Utility, use the arrow keys to select Exit > Exit Saving Changes, and then
press the enter key.
Setup Utility default settings go into effect when the computer restarts.
✎ Your password, security, and language settings are not changed when you restore the factory default settings.
5–2
Maintenance and Service Guide
Setup Utility
Exiting Setup Utility
You can exit Setup Utility with or without saving changes.
■ To exit Setup Utility and save your changes from the current session:
If the Setup Utility menus are not visible, press the esc key to return to the menu display. Then use the arrow
keys to select Exit > Exit Saving Changes, and then press the enter key.
■ To exit Setup Utility without saving your changes from the current session:
If the Setup Utility menus are not visible, press the esc key to return to the menu display. Then use the arrow
keys to select Exit > Exit Discarding Changes, and then press the enter key.
After either choice, the computer restarts in Windows.
Setup Utility menus
The menu tables in this section provide an overview of Setup Utility options.
✎ Some of Setup Utility menu items listed in this chapter might not be supported by the computer.
Main menu
Select
To do this
System information
■ View and change the system time and date.
■ View identification information about the computer.
■ View specification information about the processor, memory size,
system BIOS, and keyboard controller version (select models only).
Security menu
Select
To do this
Administrator password
Enter, change, or delete an administrator password.
Power-On password
Enter, change, or delete a power-on password.
Maintenance and Service Guide
5–3
Setup Utility
System Configuration menu
Select
To do this
Language Support
Change Setup Utility language.
Button Sound (select models only)
Enable/disable the capacitative button tapping sound.
Virtualization Technology (select models
only)
Enable/disable the processor Virtualization Technology.
Processor C6 State (select models only)
Enable/disable the processor C6 sleep state.
LAN Power Saving (select models only)
Enable/disable LAN Power Saving. When enabled, saves power when the
computer is in DC mode.
Card Reader/1394 Power Saving (select
models only)
Enable/disable Card Reader/1394 Power Saving.
Fan Always On
Enable/disable Fan Always On. When enabled, the computer fan will
always be on.
Boot Options
Set the following boot options:
■ f10 and f12 Delay (seconds)—Set the delay for the f10 and f12 functions of
Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20).
■ CD-ROM boot—Enable/disable boot from CD-ROM.
■ Floppy boot—Enable/disable boot from diskette.
■ Internal Network Adapter boot—Enable/disable boot from Internal
Network Adapter.
■ Boot Order—Set the boot order for:
Notebook hard drive
Internal CD/DVD ROM drive
USB diskette on key/USB hard disk
USB CD/DVD ROM drive
USB floppy
Network adapter
Diagnostics menu
Select
To do this
Hard Disk Self Test
Run a comprehensive self-test on the hard drive.
models with two hard drives, this menu option is called the
✎ On
Primary Hard Disk Self Test.
5–4
Secondary Hard Disk Self Test
(select models only)
Run a comprehensive self-test on a secondary hard drive.
Memory Test
Run a diagnostic test on the system memory.
Maintenance and Service Guide
6
Specifications
Computer specifications
Metric
U.S.
Length
23.7 cm
9.33 in
Width
33.4 cm
13.15 in
Height (front to rear)
3.33 to 3.97 cm
1.31 to 1.56 in
Weight
2.36 kg
5.2 lbs
Dimensions
Input power
Operating voltage
18.5 V dc to 19.0 V dc
Operating current
3.5 A or 4.74 A
Temperature
Operating (not writing to optical disc)
0°C to 35°C
32°F to 95°F
Operating (writing to optical disc)
5°C to 35°C
41°F to 95°F
Nonoperating
-20°C to 60°C
-4°F to 140°F
Relative humidity
Operating
10% to 90%
Nonoperating
5% to 95%
Maximum altitude (unpressurized)
Operating
-15 m to 3,048 m
-50 ft to 10,000 ft
Nonoperating
-15 m to 12,192 m
-50 ft to 40,000 ft
Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this
✎ range
of temperatures.
Maintenance and Service Guide
6–1
Specifications
14.1-in display specifications
Metric
U.S.
Height
30.37 cm
11.96 in
Width
18.98 cm
7.47 in
Diagonal
35.82 cm
14.10 in
Number of colors
More than 262,144
Contrast ratio
More than 300:1
Brightness
200 nits (typical)
Dimensions
Pixel resolution
6–2
Pitch
0.2373 × 0.2373 mm
Format
1280 × 800
Configuration
RGB vertical stripe
Backlight
Edge lit
Character display
80 × 25
Total power consumption
5.2 W
Viewing angle
±40° horizontal, +15°/-35° vertical (typical)
Maintenance and Service Guide
Specifications
Hard drive specifications
500-GB*
320-GB*
250-GB*
160-GB*
Height
9.5 mm
9.5 mm
9.5 mm
9.5 mm
Width
70 mm
70 mm
70 mm
70 mm
Weight
7200-rpm
115 g
115 g
115 g
115 g
Interface type
SATA
SATA
SATA
SATA
Transfer rate
100 MB/s
100 MB/s
100 MB/s
100 MB/s
Security
ATA security
ATA security
ATA security
ATA security
Single track
7200-rpm
1.5 ms
1.5 ms
1.5 ms
1.5 ms
Average
7200-rpm
11.0 ms
11.0 ms
11.0 ms
11.0 ms
Maximum
7200-rpm
22.0 ms
22.0 ms
22.0 ms
22.0 ms
Logical blocks
976,773,168
625,142,448
488,397,168
312,581,808
Disc rotational speed
7200 rpm
7200 rpm
7200 rpm
7200 rpm
Operating temperature
0°C to 60°C (32°F to 140°F)
Dimensions
Seek times (typical read, including setting)
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive
specifications might differ slightly.
✎ Certain restrictions and exclusions apply. Contact technical support for details.
Maintenance and Service Guide
6–3
Specifications
Blu-ray ROM DVD±R/RW SuperMulti DL Drive with LightScribe specifications
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI,
CD-TEXT, CD-ROM, CD-ROM
XA, MIXED MODE CD, CD-I,
CD-I Bridge (Photo-CD, Video
CD), Multisession CD
(Photo-CD, CD-EXTRA,
Portfolio, CD-R, CD-RW),
CD-R, CD-RW, DVD-ROM
(DVD-5, DVD-9, DVD-10,
DVD-18), DVD-R, DVD-RW,
BD-ROM, BD-R, BD-RE
CD-R, CD-RW, DVD+R,
DVD+R(9), DVD+RW, DVD-R,
DVD-R(9), DVD-RW,
DVD-RAM, LightScribe
Interface
SATA
Access time
CD
DVD
BD
Random
< 190 ms
< 190 ms
< 230 ms
Max data transfer rate
6–4
24X CD-ROM
3,600 KB/sec
8X DVD-ROM
10,800 KB/sec
4X BD-ROM
18,000 KB/sec
16X - CD-R
1,200 KB/sec
10X - CD-RW
1,500 KB/sec
8X DVD+R
10,800 KB/sec
8X - DVD+RW
10,800 KB/sec
8X - DVD-R
10,800 KB/sec
6X - DVD-RW
8,100 KB/sec
4X - DVD+R Dual Layer
5,400 KB/sec
4X - DVD-R Dual Layer
5,400 KB/sec
5X DVD-RAM
6,750 KB/sec
Max media capacity (read)
50.0 GB
Max media capacity (write)
8.5 GB
Transport
Tray loading
Maintenance and Service Guide
Specifications
DVD±RW SuperMulti DL Drive with LightScribe specifications
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI,
CD-TEXT, CD-ROM, CD-ROM
XA, MIXED MODE CD, CD-I,
CD-I Bridge (Photo-CD, Video
CD), Multisession CD
(Photo-CD, CD-EXTRA,
Portfolio, CD-R, CD-RW),
CD-R, CD-RW, DVD-ROM
(DVD-5, DVD-9, DVD-10,
DVD-18), DVD-R, DVD-RW,
DVD+R, DVD+RW, DVD-RAM
CD-R, CD-RW, DVD+R,
DVD+RW, DVD-R, DVD-RW,
DVD-RAM, LightScribe
Interface
SATA
Access time
CD
DVD
Random
< 150 ms
< 160 ms
Max data transfer rate
24X CD-ROM
3,600 KB/sec
8X DVD-ROM
10,800 KB/sec
24X CD-R
3,600 KB/sec
16X CD-RW
2,400 KB/sec
8X DVD+R
10,800 KB/sec
8x DVD+RW
10,800 KB/sec
8X DVD-R
10,800 KB/sec
6X DVD-RW
8,100 KB/sec
4X DVD-R Dual Layer
5,400 KB/sec
4X DVD+R Dual Layer
5,400 KB/sec
5X DVD-RAM
6,750 KB/sec
Max media capacity (read)
8.5 GB
Max media capacity (write)
8.5 GB
Transport
Tray loading
Maintenance and Service Guide
6–5
Specifications
System DMA specifications
Hardware
DMA System function
DMA0
Reserve
DMA1
Reserve
DMA2
Reserve
DMA3
Reserve
DMA4
Direct memory access controller
DMA5
Reserve
DMA6
Reserve
DMA7
Reserve
System interrupt specifications (for models with discrete graphics subsystems)
6–6
Hardware IRQ
System function
IRQ1
Standard PS/2 Keyboard
IRQ12
PS/2 Compatible Mouse
IRQ13
Numeric data processor
IRQ16
High Definition Audio Controller
IRQ16
Standard OpenHCD USB Host Controller
IRQ16
Standard Opened USB Host Controller
IRQ17
PCI standard PCI-to-PCI bridge
IRQ17
Standard Enhanced PCI to USB Host Controller
IRQ18
Broadcom 802.11g Network Adapter
IRQ18
PCI standard PCI-to-PCI bridge
IRQ18
PCI standard PCI-to-PCI bridge
IRQ18
Standard OpenHCD USB Host Controller
IRQ18
Standard OpenHCD USB Host Controller
IRQ19
High Definition Audio Controller
IRQ19
PCI standard PCI-to-PCI bridge
IRQ19
Realtek RTL8102E/RTL8103E Family PCI-E Fast Ethernet NIC (NDIS 6.20)
IRQ19
Standard Enhanced PCI to USB Host Controller
IRQ22
Standard AHCI 1.0 Serial ATA Controller
IRQ(-2)
ATI Mobility Radeon HD 4330 Series
IRQ81-190
Microsoft ACPI-Compliant System
Maintenance and Service Guide
Specifications
System interrupt specifications (for models with UMA graphics subsystems)
Hardware IRQ
System function
IRQ1
Standard 101/102-key keyboard or Microsoft Natural PS/2 Keyboard with HP
IRQ12
PS/2 Compatible Mouse
IRQ13
Numeric data processor
IRQ16
High Definition Audio Controller
IRQ16
Standard OpenHCD USB Host Controller
IRQ16
Standard OpenHCD USB Host Controller
IRQ17
PCI standard PCI-to-PCI bridge
IRQ17
Standard Enhanced PCI to USB Host Controller
IRQ18
Atheros AR5009 802.11a/g/n WiFi Adapter
IRQ18
PCI standard PCI-to-PCI bridge
IRQ18
Standard OpenHCD USB Host Controller
IRQ18
Standard OpenHCD USB Host Controller
IRQ19
High Definition Audio Controller
IRQ19
PCI standard PCI-to-PCI bridge
IRQ19
Realtek PCIe FE Family Controller
IRQ19
Standard Enhanced PCI to USB Host Controller
IRQ22
Standard AHCI 1.0 Serial ATA Controller
IRQ81-190
Microsoft ACPI-Compliant System
Maintenance and Service Guide
6–7
Specifications
System I/O address specifications (for models with discrete graphics
subsystems)
I/O address (hex)
System function (shipping configuration)
000 - 00F
Direct memory access controller
010 - 01F
Motherboard resources
020 - 021
Programmable interrupt controller
02E - 02F
Motherboard resources
040 - 043
System timer
060 - 060
Standard PS/2 Keyboard
061 - 061
System speaker
062 - 062
Microsoft ACPI-Compliant Embedded controller
064 - 064
Standard PS/2 Keyboard
066 - 066
Microsoft ACPI-Compliant Embedded controller
068 - 068
Standard PS/2 Keyboard
06C - 06C
Standard PS/2 Keyboard
070 - 071
System CMOS/real time clock
072 - 073
Motherboard resources
080 - 080
Motherboard resources
081 - 08F
Direct memory access controller
092 - 092
Motherboard resources
0A0 - 0A1
Programmable interrupt controller
0B0 - 0B1
Motherboard resources
0C0 - 0DF
Direct memory access controller
0F0 - 0FE
Numeric data processor
3B0 - 3BB
ATI Mobility Radeon HD 4330 Series
3B0 - 3BB
PCI standard PCI-to-PCI bridge
3C0 - 3DF
ATI Mobility Radeon HD 4330 Series
3C0 - 3DF
PCI standard PCI-to-PCI bridge
400 - 4CF
Motherboard resources
4D0 - 4D1
Motherboard resources
4D6 - 4D6
Motherboard resources
680 - 6FF
Motherboard resources
77A - 77A
Motherboard resources
C00 - C01
Motherboard resources
C14 - C14
Motherboard resources
C50 - C52
Motherboard resources
C6C - C6C
Motherboard resources
(Continued)
6–8
Maintenance and Service Guide
Specifications
I/O address (hex)
System function (shipping configuration)
C6F - C6F
Motherboard resources
CD0 - CDB
Motherboard resources
2000 - 20FF
Realtek RTL8102E/RTL8103E Family PCI-E Fast Ethernet NIC (NDIS 6.20)
2000 - 2FFF
PCI standard PCI-to-PCI bridge
3000 - 30FF
ATI Mobility Radeon HD 4330 Series
3000 - 3FFF
PCI standard PCI-to-PCI bridge
4010 - 401F
Standard AHCI 1.0 Serial ATA Controller
4030 - 4037
Standard AHCI 1.0 Serial ATA Controller
4038 - 403F
Standard AHCI 1.0 Serial ATA Controller
4048 - 404B
Standard AHCI 1.0 Serial ATA Controller
404C - 404F
Standard AHCI 1.0 Serial ATA Controller
Maintenance and Service Guide
6–9
Specifications
System I/O address specification (for models with UMA graphics subsystems)
I/O address (hex)
System function (shipping configuration)
000 - 00F
Direct memory access controller
010 - 01F
Motherboard resources
020 - 021
Programmable interrupt controller
02E - 02F
Motherboard resources
040 - 043
System timer
060 - 060
Standard 101/102-key keyboard or Microsoft Natural PS/2 Keyboard with HP
061 - 061
System speaker
062 - 062
Microsoft ACPI-Compliant Embedded controller
064 - 064
Standard 101/102-key keyboard or Microsoft Natural PS/2 Keyboard with HP
066 - 066
Microsoft ACPI-Compliant Embedded controller
068 - 068
Standard 101/102-key keyboard or Microsoft Natural PS/2 Keyboard with HP
06C - 06C
Standard 101/102-key keyboard or Microsoft Natural PS/2 Keyboard with HP
070 - 071
System CMOS/real time clock
072 - 073
Motherboard resources
080 - 080
Motherboard resources
081 - 08F
Direct memory access controller
092 - 092
Motherboard resources
0A0 - 0A1
Programmable interrupt controller
0B0 - 0B1
Motherboard resources
0C0 - 0DF
Direct memory access controller
0F0 - 0FE
Numeric data processor
3B0 -3BB
PCI standard PCI-to-PCI bridge
3C0 - 3DF
PCI standard PCI-to-PCI bridge
400 - 4CF
Motherboard resources
4D0 - 4D1
Motherboard resources
4D6 - 4D6
Motherboard resources
680 - 6FF
Motherboard resources
77A - 77A
Motherboard resources
C00 - C01
Motherboard resources
C14 - C14
Motherboard resources
C50 - C52
Motherboard resources
C6C - C6C
Motherboard resources
C6F - C6F
Motherboard resources
CD0 - CDB
Motherboard resources
2000 - 20FF
Realtek PCIe Fe Family Controller
(Continued)
6–10
Maintenance and Service Guide
Specifications
I/O address (hex)
System function (shipping configuration)
2000 - 2FFF
PCI standard PCI-to-PCI bridge
3000 - 3FFF
PCI standard PCI-to-PCI bridge
4010 - 401F
Standard AHCI 1.0 Serial ATA Controller
4030 - 4037
Standard AHCI 1.0 Serial ATA Controller
4038 - 403F
Standard AHCI 1.0 Serial ATA Controller
4048 - 404B
Standard AHCI 1.0 Serial ATA Controller
404C - 404F
Standard AHCI 1.0 Serial ATA Controller
Maintenance and Service Guide
6–11
7
Backup and recovery
Overview
Recovery after a system failure is as complete as your most current backup. HP recommends creating recovery
discs immediately after software setup. As you add new software and data files, continue to back up your system on
a regular basis to maintain a reasonably current backup.
Tools provided by the operating system and HP Recovery Manager software are designed to help you with the
following tasks for safeguarding your information and restoring it in case of a system failure:
■
Creating a set of recovery discs (Recovery Manager software feature). Recovery discs are used to start up
(boot) the computer and restore the operating system and software programs to factory settings in case of
system failure or instability.
■
Backing up your information regularly to protect your important system files.
■
Creating system restore points (operating system feature). System restore points allow you to reverse
undesirable changes to the computer by restoring the computer to an earlier state.
■
Recovering a program or driver (Recovery Manager software feature). This feature helps you reinstall a
program or driver without performing a full system recovery.
■
Performing a full system recovery (Recovery Manager software feature). With Recovery Manager, you can
recover your full factory image if you experience system failure or instability. Recovery Manager works from a
dedicated recovery partition (select models only) on the hard drive or from recovery discs you create.
Computers with a solid-state drive (SSD) might not have a recovery partition. Recovery discs are included for
✎ computers
that do not have a partition. Use these discs to recover your operating system and software. To check
for the presence of a recovery partition, click Start, right-click Computer, click Manage, and then click Disk
Management. If the partition is present, an HP Recovery drive is listed in the window.
Maintenance and Service Guide
7–1
Backup and recovery
Creating recovery discs
HP recommends creating recovery discs to be sure that you can restore your system to its original factory state if
you experience serious system failure or instability. Create these discs after setting up the computer for the first
time.
Handle these discs carefully and keep them in a safe place. The software allows the creation of only one set of
recovery discs.
the computer does not include an internal optical drive, use an optional external optical drive (purchased
✎ Ifseparately)
to create recovery discs, or purchase recovery discs for the computer from the HP website.
Note the following guidelines before creating recovery discs:
■
Use high-quality DVD-R, DVD+R, BD-R (writable Blu-ray), or CD-R discs. All these discs are purchased
separately. DVDs and BDs have a much higher capacity than CDs. If using CDs, up to 20 discs might be
required, whereas only a few DVDs or BDs are required.
discs, such as CD-RW, DVD±RW, double-layer DVD±RW, and BD-RE (rewritable
✎ Read-write
Blu-ray) discs, are not compatible with the Recovery Manager software.
■
The computer must be connected to AC power during this process.
■
Only one set of recovery discs can be created per computer.
■
Number each disc before inserting it into the optical drive.
■
If necessary, exit the program before you have finished creating the recovery discs. The next time you open
Recovery Manager, are be prompted to continue the disc creation process.
To create a set of recovery discs:
1. Select Start > All Programs > Recovery Manager > Recovery Disc Creation.
2. Follow the on-screen instructions.
7–2
Maintenance and Service Guide
Backup and recovery
Backing up your information
As you add new software and data files, back up your system on a regular basis to maintain a reasonably current
backup. Back up your system at the following times:
■
At regularly scheduled times
✎ Set reminders to back up your information periodically.
■
Before the computer is repaired or restored
■
Before you add or modify hardware or software
When backing up:
■
Create system restore points using the Windows System Restore feature, and periodically copy them to disc.
■
Store personal files in the Documents library and back up this folder periodically.
■
Back up templates stored in their associated programs.
■
Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings. The screen
shot is a time-saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document:
1. Display the screen.
2. Copy the screen:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
3. Open a word-processing document, and then select Edit > Paste.
4. Save the document.
■
Back up your information to an optional external hard drive, a network drive, or discs.
■
When backing up to discs, use any of the following types of discs (purchased separately): CD-R, CD-RW,
DVD+R, DVD-R, or DVD±RW. The discs used will depend on the type of optical drive installed in the
computer.
store more information than CDs, so using them for backup reduces the number of recovery
✎ DVDs
discs required.
■
When backing up to discs, number each disc before inserting it into the optical drive of the computer.
Maintenance and Service Guide
7–3
Backup and recovery
Using Windows Backup and Restore
✎ Be sure that the computer is connected to AC power before starting the backup process.
✎ The backup process might take over an hour, depending on file size and the speed of the computer.
To create a backup using Windows Backup and Restore:
1. Select Start > All Programs > Maintenance > Backup and Restore.
2. Follow the on-screen instructions to set up and create a backup.
includes the User Account Control feature to improve the security of the computer. You might be
✎ Windows
prompted for your permission or password for tasks such as installing software, running utilities, or changing
Windows settings. See Help and Support.
Using system restore points
When backing up your system, you are creating a system restore point. A system restore point allows you to save
and name a snapshot of your hard drive at a specific point in time. You can then recover back to that point if you
want to reverse subsequent changes made to your system.
to an earlier restore point does not affect data files saved or e-mails created since the last
✎ Recovering
restore point.
Create additional restore points to provide increased protection for your system files and settings.
Create restore points
■
Before adding or extensively modifying software or hardware.
■
Periodically, whenever the system is performing optimally.
✎ If you revert to a restore point and then change your mind, you can reverse the restoration.
7–4
Maintenance and Service Guide
Backup and recovery
To Create a system restore point
To create a system restore point:
1. Select Start > Control Panel > System and Security > System.
2. In the left pane, click System Protection.
3. Click the System Protection tab.
4. Under Protection Settings, select the disk for which you want to create a restore point.
5. Click Create.
6. Follow the on-screen instructions.
Restore to a previous date and time
To revert to a restore point (created at a previous date and time), when the computer was functioning optimally:
1. Select Start > Control Panel > System and Security > System.
2. In the left pane, click System protection.
3. Click the System Protection tab.
4. Click System Restore.
5. Follow the on-screen instructions.
Performing a recovery
only files that you have previously backed up. HP recommends using HP Recovery Manager to create a
✎ Recover
set of recovery discs (entire drive backup) as soon as you set up the computer.
Recovery Manager software allows you to repair or restore the system if you experience system failure or
instability. Recovery Manager works from recovery discs or from a dedicated recovery partition (select models
only) on the hard drive. However, if the computer includes a solid-state drive (SSD), you might not have a recovery
partition. If that is the case, recovery discs are included with the computer. Use these discs to recover the operating
system and software.
has its own built-in repair features, such as System Restore. If you have not already tried these features,
✎ Windows
try them before using Recovery Manager.
Manager recovers only software that was preinstalled at the factory. Software not provided with this
✎ Recovery
computer must be downloaded from the manufacturer's website or reinstalled from the disc provided by the
manufacturer.
Maintenance and Service Guide
7–5
Backup and recovery
Recovering from the recovery discs
To restore the system from the recovery discs:
1. Back up all personal files.
2. Insert the first recovery disc into the optical drive and restart the computer.
3. Follow the on-screen instructions.
Recovering from the dedicated recovery partition (select models only)
with an SSD might not have a recovery partition. If the computer does not have a recovery partition,
✎ Computers
you are not able to recover using this procedure. Recovery discs are included for computers that do not have a
partition. Use these discs to recover your operating system and software.
On some models, a recovery can be performed from the partition on the hard drive, accessed by pressing either the
Start button or the f11 key. This restores the computer to its factory condition.
To restore the system from the partition:
1. Access Recovery Manager by either:
❏ Selecting Start > All Programs > Recovery Manager > Recovery Manager.
– or –
❏ Turning on or restarting the computer, and then pressing the esc key when the Press the ESC key for Startup
Menu message appears at the bottom of the screen. Then, press the f11 key when the Press <F11> for
recovery message appears on the screen.
2. Click System Recovery in the Recovery Manager window.
3. Follow the on-screen instructions.
7–6
Maintenance and Service Guide
8
Connector pin assignments
Audio-in (microphone)
Pin
Signal
1
Audio signal in
2
Audio signal in
3
Ground
Audio-out (headphone)
Pin
Signal
1
Audio out, left channel
2
Audio out, right channel
3
Ground
Maintenance and Service Guide
8–1
Connector pin assignments
External monitor
8–2
Pin
Signal
1
Red analog
2
Green analog
3
Blue analog
4
Not connected
5
Ground
6
Ground analog
7
Ground analog
8
Ground analog
9
+5 VDC
10
Ground
11
Monitor detect
12
DDC 2B data
13
Horizontal sync
14
Vertical sync
15
DDC 2B clock
Maintenance and Service Guide
Connector pin assignments
HDMI
Pin
Signal
1
Transition minimized differential signal (TDMS) data 2+
2
TDMS data 2 shield
3
TDMS data 2-
4
TDMS data 1+
5
TDMS data 1 shield
6
TDMS data 1 shield
7
TDMS data 0+
8
TDMS data 0 shield
9
TDMS data 0-
10
TDMS clock +
11
TDMS data clock shield
12
TDMS data clock-
13
Consumer electronics control
14
Not connected
15
Display data channel (DDC) clock
16
DDC data
17
Ground
18
+5V Power
19
Hot plug detect
Maintenance and Service Guide
8–3
Connector pin assignments
RJ-11 (modem) (select models only)
8–4
Pin
Signal
1
Unused
2
Tip
3
Ring
4
Unused
5
Unused
6
Unused
Maintenance and Service Guide
Connector pin assignments
RJ-45 (network)
Pin
Signal
1
Transmit +
2
Transmit -
3
Receive +
4
Unused
5
Unused
6
Receive -
7
Unused
8
Unused
Maintenance and Service Guide
8–5
Connector pin assignments
Universal Serial Bus
8–6
Pin
Signal
1
+5 VDC
2
Data
3
Data +
4
Ground
Maintenance and Service Guide
9
Power cord set requirements
The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC
or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the country or region
where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or region where
the computer is used.
Requirements for all countries and regions
The requirements listed below are applicable to all countries and regions:
■
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
■
All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the
country or region where the power cord set will be used.
■
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating of 125 or
250 V AC, as required by the power system of each country or region.
■
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard Sheet C13
connector for mating with the appliance inlet on the back of the computer.
Maintenance and Service Guide
9–1
Power cord set requirements
Requirements for specific countries and regions
Country/region
Accredited agency
Applicable note number
Australia
EANSW
1
Austria
OVE
1
Belgium
CEBC
1
Canada
CSA
2
Denmark
DEMKO
1
Finland
FIMKO
1
France
UTE
1
Germany
VDE
1
Italy
IMQ
1
Japan
METI
3
The Netherlands
KEMA
1
Norway
NEMKO
1
The People's Republic of China
CCC
5
South Korea
EK
4
Sweden
SEMKO
1
Switzerland
SEV
1
Taiwan
BSMI
4
The United Kingdom
BSI
1
The United States
UL
2
1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
2. The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type
with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3. The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the Japanese
Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall plug must be a
two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4. The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
5. The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
9–2
Maintenance and Service Guide
10
Recycling
Battery
When the battery has reached the end of its useful life, do not dispose of the battery in general household waste.
Follow the local laws and regulations in your area for computer battery disposal.
Display
Å
WARNING: The backlight contains mercury. Caution must be exercised when removing and handling the backlight to avoid
damaging this component and causing exposure to the mercury.
Ä
CAUTION: The procedures in this chapter can result in damage to display components. The only components intended for
recycling purposes are the liquid crystal display (LCD) panel and the backlight. When removing these components, handle them
carefully.
Materials Disposal. This HP product contains mercury in the backlight in the display assembly that might
✎ require
special handling at end-of-life. Disposal of mercury might be regulated because of environmental
considerations. For disposal or recycling information, contact your local authorities, or see the Electronic
Industries Alliance (EIA) website at http://www.eiae.org.
This section provides disassembly instructions for the display assembly. The display assembly must be
disassembled to gain access to the backlight 1 and the liquid crystal display (LCD) panel 2.
procedures provided in this chapter are general disassembly instructions. Specific details, such as screw
✎ The
sizes, quantities, and locations, and component shapes and sizes, can vary from one computer model to another.
Maintenance and Service Guide
10–1
Recycling
To disassemble the display assembly:
1. Remove all screw covers 1 and screws 2 that secure the display bezel to the display assembly.
2. Lift up and out on the left and right inside edges 1 and the top and bottom inside edges 2 of the display bezel
until the bezel disengages from the display assembly.
3. Remove the display bezel 3.
10–2
Maintenance and Service Guide
Recycling
4. Disconnect all display panel cables 1 from the display inverter and remove the inverter 2.
5. Remove all screws 1 that secure the display panel assembly to the display enclosure.
6. Remove the display panel assembly 2 from the display enclosure.
7. Turn the display panel assembly upside down.
8. Remove all screws that secure the display panel frame to the display panel.
Maintenance and Service Guide
10–3
Recycling
9. Use a sharp-edged tool to cut the tape 1 that secures the sides of the display panel to the display panel frame.
10. Remove the display panel frame 2 from the display panel.
11. Remove the screws 1 that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover 2 and swing it outward.
13. Remove the backlight cover.
14. Turn the display panel right-side up.
15. Remove the backlight cables 1 from the clip 2 in the display panel.
10–4
Maintenance and Service Guide
Recycling
16. Turn the display panel upside down.
Å
WARNING: The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging
this component and causing exposure to the mercury.
17. Remove the backlight frame from the display panel.
18. Remove the backlight from the backlight frame.
Maintenance and Service Guide
10–5
Recycling
19. Disconnect the display cable 1 from the LCD panel.
20. Remove the screws 2 that secure the LCD panel to the display rear panel.
21. Release the LCD panel 3 from the display rear panel.
22. Release the tape 4 that secures the LCD panel to the display rear panel.
23. Remove the LCD panel.
24. Recycle the LCD panel and backlight.
10–6
Maintenance and Service Guide
Index
A
AC adapter
location 2–12
spare part numbers 3–11, 3–12
administrator password 5–3
antenna
disconnecting 4–16, 4–18
removal 4–33
spare part numbers 3–8, 3–13, 4–33
audio board
removal 4–42
spare part numbers 3–7, 3–12, 4–42
audio board cable
removal 4–42
spare part numbers 3–7, 3–12, 4–42
audio product description 1–2
audio-in jack
connector pinout 8–1
location 2–6
audio-out jack
connector pinout 8–1
location 2–6
B
backing up
personal files 7–3
system information 7–1, 7–3
templates 7–3
window, toolbar, and menu bar settings 78–3
Backup and Restore (Windows) 7–4
base enclosure, spare part number 3–7
battery
location 2–12
removal 4–7
spare part numbers 3–7, 3–12, 4–7
battery bay 2–10
battery light 2–2, 2–6
battery release latch 2–10
Bluetooth module
removal 4–38
spare part numbers 3–7, 3–15, 4–38
Bluetooth module cable
removal 4–38
spare part numbers 3–7, 3–15, 4–38
Maintenance and Service Guide
Blu-ray ROM with LightScribe DVD±R/RW
SuperMulti Double-Layer Drive
precautions 4–2
removal 4–20
spare part numbers 3–15, 4–20
specifications 6–4
boot options 5–4
boot order 5–4
bottom components 2–10
button components 2–3
button sound 5–4
buttons
power 2–3
TouchPad 2–1
TouchPad on/off 2–1
wireless 2–3
C
cables, service considerations 4–1
caps lock light 2–2
Card Reader Power Saving 5–4
changing Setup Utility language 5–1
chipset product description 1–1
components
bottom 2–10
buttons 2–3
display 2–5
front 2–6
keys 2–4
left-side 2–9
lights 2–2
pointing device 2–1
rear 2–7
right-side 2–8
top 2–1
TouchPad 2–1
computer feet
locations 4–6
spare part number 4–6
computer specifications 6–1
connector pinout
audio-in jack 8–1
audio-out jack 8–1
external monitor port 8–2
Index–1
Index
HDMI port 8–3
headphone jack 8–1
microphone jack 8–1
modem jack 8–4
monitor port 8–2
network jack 8–5
RJ-11 jack 8–4
RJ-45 jack 8–5
USB port 8–6
connectors, service considerations 4–1
D
Diagnostics menu, Setup Utility 5–4
Digital Media slot light 2–9
Digital Media slot, location 2–9
display assembly
removal 4–27
spare part numbers 3–3, 3–15, 4–27
display assembly cable, spare part number 3–12
display bezel, spare part numbers 3–8, 3–16
display components, recycling 10–1
display enclosure
removal 4–30
spare part numbers 3–8, 3–12, 3–13
display hinge
removal 4–33
spare part numbers 3–8, 3–12, 4–33
display inverter, removal 10–3
display panel
product description 1–1
removal 4–32
spare part number 3–8, 3–12, 4–32
Display Rubber Kit, spare part number 3–12
Display Screw Kit, spare part number 3–12
display spare part numbers 2–5
displaying system information 5–2
drive light 2–2, 2–6
drives, boot order 5–4
DVD±RW and CD-RW SuperMulti Double-Layer
Combo Drive
spare part numbers 3–15
DVD±RW and CD-RW SuperMulti Double-Layer
Combo Drive with LightScribe
precautions 4–2
removal 4–20
spare part numbers 3–15, 4–20
specifications 6–5
E
electrostatic discharge 4–2
equipment guidelines 4–4
eSATA/USB port 2–9
esc key 2–4
Index–2
Ethernet product description 1–2
exiting Setup Utility 5–3
external media card product description 1–3
external monitor port
connector pinout 9–2
illustrated 2–9
F
f11 key 7–6
fan
removal 4–56
spare part numbers 3–3, 3–12, 4–56
fan always on 5–4
fan/heat sink assembly
removal 4–52
spare part numbers 4–52
feet
locations 4–6
spare part number 4–6
fn key 2–4
front components 2–6
function keys 2–4
G
graphics product description 1–1
grounding equipment and methods 4–2
H
hard drive
precautions 4–2
product description 1–2
removal 4–8
spare part numbers 3–7, 3–10, 3–12, 3–13, 3–15,
3–16, 4–8
specifications 6–3
hard drive bay 2–10
hard drive bracket, removal 4–9
hard drive cover, illustrated 3–9
Hard Drive Hardware Kit, spare part numbers 3–7,
3–10, 3–12, 4–8
hard drive self test 5–4
HDMI port
connector pinout 9–3
illustrated 2–9
headphone jack
connector pinout 8–1
location 2–6
heat sink
removal 4–52
spare part numbers 3–3, 3–15
hinge
removal 4–33
spare part numbers 3–8, 3–12
Maintenance and Service Guide
Index
I
internal display switch
illustrated 2–5
spare part number 3–13
inverter
removal 4–31
spare part number 3–8, 3–12, 4–31
J
jacks
audio-in 2–6
audio-out 2–6
headphone 2–6
microphone 2–6
K
key components 2–4
keyboard
product description 1–3
removal 4–21
spare part numbers 3–3, 3–12, 4–21
keyboard cover
removal 4–23
spare part numbers 3–3, 3–12, 4–23
keys
esc 2–4
f11 7–6
fn 2–4
function 2–4
numeric keypad 2–4
Windows applications 2–4
Windows logo 2–4
L
LAN Power Saving 5–4
language support, Setup Utility 5–4
left-side components 2–9
lights
battery 2–2, 2–6
caps lock 2–2
Digital Media slot 2–9
drive 2–2, 2–6
illustrated 2–2
num lock 2–2
optical drive 2–8
power 2–2, 2–6
TouchPad 2–1
webcam 2–5
wireless 2–2
M
Main menu, Setup Utility 5–3
major components, spare part numbers 3–2
mass storage devices, spare part numbers 3–10
Maintenance and Service Guide
memory module
removal 4–10
spare part numbers 3–7, 3–12, 3–13, 4–10
memory module compartment 2–10
memory module cover, illustrated 3–9
memory product description 1–2
memory test 5–4
microphone jack
connector pinout 8–1
location 2–6
microphone module
illustrated 2–5
product description 1–2
removal 4–34
spare part numbers 3–8, 3–14, 4–34
Mini Card bracket, spare part numbers 3–15
Mini Card compartment cover, illustrated 3–9
Mini Card compartment, illustrated 2–10
model name 3–1, 4–5
modem jack, connector pinout 8–4
modem module
product description 1–2
removal 4–40
spare part numbers 3–3, 3–13, 4–40
modem module cable
removal 4–51
spare part numbers 3–3, 3–13, 4–51
monitor port, connector pinout 8–2
N
navigating in Setup Utility 5–2
navigation keys 2–4
network jack,connector pinout 8–5
num lock light 2–2
numeric keypad keys 2–4
O
operating system product description 1–4
optical drive
location 2–8
precautions 4–2
product description 1–2
removal 4–20
spare part numbers 3–7, 3–10, 4–20
specifications 6–4, 6–5
optical drive light 2–8
P
packing guidelines 4–3
part number 3–1
passwords 5–3
plastic parts 4–1
Index–3
Index
Plastics Kit
contents 3–9
spare part numbers 3–3, 3–9
spare parts numbers 3–13
pointing device
components 2–1
illustrated 2–1
product description 1–3
ports
eSATA/USB 2–9
external monitor 2–9
HDMI 2–9
RJ-11 2–8
USB 2–8
ports product description 1–3
power button 2–3
power connector and cable
location 2–8
removal 4–46
spare part number 3–6, 4–46
power connector cable, spare part number 3–12
power cord
location 2–12
set requirements 9–1
spare part numbers 3–11, 3–13
power light 2–2, 2–6
power requirements product description 1–3
Power Saving 5–4
power-on password 5–3
processor
product description 1–1
removal 4–57
spare part numbers 3–7, 3–15, 3–16, 4–57
Processor C6 State 5–4
product description
audio 1–2
chipset 1–1
display panel 1–1
Ethernet 1–2
external media card 1–3
graphics 1–1
hard drive 1–2
keyboard 1–3
memory 1–2
microphone 1–2
modem 1–2
operating system 1–4
optical drive 1–2
pointing device 1–3
ports 1–3
power requirements 1–3
processor 1–1
Index–4
security 1–4
serviceability 1–4
webcam 1–2
wireless 1–3
product name 1–1, 3–1, 4–5
product number 3–1
R
rear components 2–7
recovery
full system 7–1, 7–5
programs or drivers 7–1
using the recovery discs 7–6
using the recovery partition 7–6
recovery discs
creating 7–2
defined 7–1
performing a recovery 7–6
Recovery Manager 7–1
recovery partition
defined 7–1
performing a recovery 7–6
recycling
battery 10–1
display components 10–1
removal/replacement
preliminaries 4–1
procedures 4–5
restore points 7–1, 7–3, 7–4
restoring default settings in Setup Utility 5–2
right-side components 2–8
RJ-11 (modem) jack
connector pinout 8–4
location 2–8
RJ-45 (network) jack
connector pinout 8–5
location 2–9
RTC battery
removal 4–12
spare part number 3–7, 3–12, 4–12
Rubber Feet Kit, spare part number 3–7, 4–6
Rubber Kit, spare part number 3–12
S
Screw Kit, spare part number 3–11, 3–12
screw listing 7–1
secondary hard drive self test 5–4
security cable slot 2–9
Security menu, Setup Utility 5–3
security product description 1–4
selecting in Setup Utility 5–2
serial number 3–1, 4–5
service considerations 4–1
Maintenance and Service Guide
Index
service tag 3–1, 4–5
serviceability product description 1–4
Setup Utility
changing the language 5–1
Diagnostics menu 5–4
displaying system information 5–3
exiting 5–3
Main menu 5–3
menus 5–3
navigating and selecting 5–2
restoring default settings 5–2
Security menu 5–3
starting 5–1
System Configuration menu 5–4
using 5–1
slots, security cable 2–9
solid-state drive (SSD) 7–1, 7–5, 7–6
speaker assembly
illustrated 2–3
removal 4–25
spare part number 3–3, 3–12, 4–25
specifications
Blu-ray ROM with LightScribe DVD±R/RW
SuperMulti Double-Layer Drive 6–4
computer 6–1
display assembly 6–2, 6–3
DVD±RW and CD-RW SuperMulti Double-Layer
Combo Drive with LightScribe 6–5
hard drive 6–3
optical drive 6–4, 6–5
system DMA 6–6
system I/O address 6–11, 6–13
system interrupt 6–9, 6–10
system board
removal 4–48
spare part numbers 3–3, 3–15, 4–48
System Configuration menu, Setup Utility 5–4
system DMA specifications 6–6
system I/O address specifications 6–11, 6–13
system information 5–3
system interrupt specifications 6–9, 6–10
system recovery 7–1
system restore points 7–1, 7–3, 7–4
TouchPad light 2–1
TouchPad on/off button 2–1
TouchPad scroll zone 2–1
U
Universal Serial Bus (USB) port
connector pinout 8–6
location 2–8
USB board
removal 4–44
spare part number 3–4, 3–12, 4–44
USB board cable
removal 4–44
spare part number 3–12, 4–44
V
vent 2–7, 2–10
Virtualization Technology 5–4
W
warranty period 3–1, 4–5
webcam
location 2–5
product description 1–2
webcam light 2–5
webcam module
removal 4–33
spare part numbers 3–8, 3–12, 4–33
webcam/microphone module, spare part number 3–8
Windows applications key 2–4
Windows Backup and Restore 7–4
Windows logo key 2–4
wireless antenna 2–11
disconnecting 4–16, 4–18
removal 4–33
spare part numbers 3–8, 3–13, 4–33
wireless button 2–3
wireless light 2–2
wireless module compartment cover, removal 4–16,
4–18
wireless product description 1–3
WLAN module
removal 4–14
spare part numbers 3–4, 3–13, 3–14, 3–15, 4–14
workstation guidelines 4–3
T
tools required 4–1
top components 2–1
top cover
removal 4–35
spare part numbers 3–3, 3–12, 4–35
TouchPad 2–1
TouchPad button 2–1
TouchPad components, illustrated 2–1
Maintenance and Service Guide
Index–5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement