Samsung | L7 | Instruction manual | Samsung L7 Instruction manual

MICRO COMPONENT
SYSTEM
CD-R/RW PLAYBACK
MM-L7
Instruction Manual
Downloaded From Disc-Player.com Samsung Manuals
Safety Warnings
GB
Use of controls, adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
CAUTION-INVISIBLE LASER RADIATION WHEN OPEN
AND INTERLOCKS DEFEATED, AVOID EXPOSURE TO
BEAM.
This symbol indicates that dangerous voltage
which can cause electric shock is present inside
this unit.
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE REAR COVER,
NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a
CLASS 1 LASER product.
This symbol alerts you to important operating
and maintenance instructions accompanying the
unit.
WARNING: To reduce the risk of fire or electric shock, do
not expose this appliance to rain or moisture.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
Wiring the Mains Power Supply Plug (UK only)
IMPORTANT NOTICE
The main lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin
face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used.
Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same
colour as the fuse fitted in the plug. Replacement covers are available from your dealer. If the fitted plug is not suitable for the power
points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension
lead or consult your dealer for assistance. However, if there is no alternative to cutting off the plug, remove the fuse and then safely
dispose of the plug. Do not connect the plug to a main socket as there is a risk of shock hazard from the bared flexible cord.
Never attempt to insert bare wires directly into a main socket. A plug and fuse must be used at all times.
IMPORTANT
The wires in the main lead are coloured in accordance with the following code:–
BLUE = NEUTRAL
BROWN = LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:–
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire
coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE LETTER E OR BY
THE EARTH SYMBOL
, OR COLOURED GREEN OR GREEN AND YELLOW.
2
Downloaded From Disc-Player.com Samsung Manuals
You have just purchased
a SAMSUNG micro component system.
Contents
Please take the time to read these
instructions, as they will enable you to set up
your player easily and take full advantage
of its features.
◆ INSTALLING YOUR MICRO COMPONENT SYSTEM
Safety Warnings ........................................................................................................................... 2
Front Panel View .......................................................................................................................... 4
Remote Control ............................................................................................................................ 5
Rear Panel View ........................................................................................................................... 6
Where to Install Your Micro-Component System ......................................................................... 7
Connecting Your System to the Power Supply ............................................................................ 7
Inserting Remote Control Batteries .............................................................................................. 7
Connecting to an External Source ............................................................................................... 8
CD Digital Out Jack ...................................................................................................................... 8
Connecting the Loudspeakers ...................................................................................................... 8
Connecting the AM (MW)/LW Aerial ............................................................................................. 9
Connecting the FM Aerial ............................................................................................................. 9
Setting the Clock ........................................................................................................................ 10
◆ CD PLAYER
Listening to a Compact Disc ...................................................................................................... 10
Selecting a Track ........................................................................................................................ 11
Searching for a Specific Music Passage on a CD ...................................................................... 11
Precautions When Using Compact Discs ................................................................................... 11
CD Repeat Function ................................................................................................................... 11
Programming the Order of Playback .......................................................................................... 11
Checking and Changing Programmed Tracks ........................................................................... 12
◆ TUNER
Searching for and Storing the Radio Stations ...................................................................... 12~13
Selecting a Stored Station .......................................................................................................... 13
Improving Radio Reception ........................................................................................................ 13
About RDS broadcasting ..............................................................................................................14
About RDS DISPLAY function ......................................................................................................14
PTY(Program Type) indication and PTY-SEARCH function.........................................................15
◆ TAPE DECK
Listening to a Cassette ...............................................................................................................
Selecting the Cassette Playback Mode ......................................................................................
Maintaining the Sound Quality ...................................................................................................
Recording a Radio Programme ..................................................................................................
Recording a CD with the CD Synchro Feature ..........................................................................
Repeat (A↔B) Function .............................................................................................................
Recommendations for Recording ...............................................................................................
16
16
16
17
17
17
17
◆ OTHER FEATURES
Timer Function ............................................................................................................................
Cancelling the Timer ...................................................................................................................
Setting the System to Switch Off Automatically .........................................................................
Mute Function .............................................................................................................................
Equalizer .....................................................................................................................................
Power Sound function ................................................................................................................
Connecting Headphones ............................................................................................................
◆ RECOMMENDATIONS
FOR
18
18
19
19
19
20
20
USE
Safety Precautions........................................................................................................................21
Before Contacting the After-Sales Service ...................................................................................21
Technical Specifications................................................................................................................22
Symbols
Press
Push
Important
Note
3
Downloaded From Disc-Player.com Samsung Manuals
GB
Front Panel View
GB
9
1
10
2
11
FUNC.
3
12
Volume
R
13
CD/TAPE/TUNING
4
5
6
7
8
Tuning Mode
Display
Repeat A B
CD Repeat
14
PTY
Band
Preset EQ
+10 (CD)
PROG./Set
CD Synchro
Start/Stop
Record
15
16
1.
2.
3.
4.
5.
6.
7.
8.
CD Door Open/Close( )
On / Standby
Multi-Function(CD/TAPE/TUNING)
CD Repeat
Tuning Mode(Stop)
Band
PROG./Set
CD Synchro
4
Downloaded From Disc-Player.com Samsung Manuals
9. Push Eject( )
10.Phones jack
11.Function
12.Volume control
13.Repeat (A↔B) / Display
14.+10(CD) / PTY
15.Preset EQ
16.Record Start/Stop
Remote Control
GB
9
On/Standby
Sleep
Mute
10
1
2
Power
Sound
Preset
EQ
Timer
on/off
Timer/
Clock
Tape
Mono/ST. Mode
Repeat
Program/
Set
12
3
4
11
5
6
14
CD/TAPE/MP3
Band
13
Function
15
7
VOL.
16
8
Tuning
Mode
VOL.
1.
2.
3.
4.
5.
6.
7.
8.
9.
On/Standby
Preset EQ
Power Sound
Mono / ST.
Tape Mode
Multi-Function (CD / TAPE)
Band
Volume Control
Sleep
17
10. Mute
11. Timer on / off
12. Timer / Clock
13. Program/Set
14. Repeat
15. Function
16. Radio station search
17. Tuning Mode
5
Downloaded From Disc-Player.com Samsung Manuals
Rear Panel View
GB
1
2
3
4
5
1.
2.
3.
4.
5.
FM AERIAL CONNECTOR TERMINAL
CD DIGITAL OUT JACK
AM(MW)/LW AERIAL CONNECTOR TERMINALS
AUX INPUT
LOUDSPEAKERS CONNECTOR TERMINALS
6
Downloaded From Disc-Player.com Samsung Manuals
Where to Install Your Micro-Component System
To take full advantage of your new MICRO component system,
follow these installation instructions before connecting the unit.
◆ Install the system on a flat, stable surface.
◆ Never place this unit on carpeting.
◆ Never locate this unit in an outdoor area.
◆ Maintain an open space of approximately 6 inches
(15 cm) on the sides and rear of the system, for
ventilation purposes.
◆ Make sure that you have enough room to open the
compact disc compartment easily.
◆ Place the loudspeakers at a reasonable distance on either
side of the system to ensure good stereo sound.
◆ Direct the loudspeakers towards the listening area.
◆ For optimum performance, make sure that both speakers
are placed at an equal distance above the floor.
Inserting Remote Control Batteries
Insert or replace remote control batteries when you:
Purchase the Micro component system
Find that the remote control is no longer operating
correctly
When replacing the batteries, use a new set of batteries
and never mix alkaline and manganese batteries.
1
2
Place your thumb on the position marked
on the battery
compartment cover (rear of the remote control) and push the
cover in the direction of the arrow.
Insert two AAA, LR03 or equivalent batteries, taking care to
respect the polarities:
+ on the battery against + on the remote control
– on the battery against – on the remote control
3
Replace the cover by sliding it back until it clicks into position.
FUNC.
Volume
R
CD/TAPE/TUNING
Tuning Mode
Display
Repeat A B
Repeat
PTY
Band
Preset EQ
+10 (CD)
PRO./Set
CD Synchro
Star/Stop
Record
Connecting Your System to the Power Supply
The main lead must be plugged into an appropriate socket.
Before plugging your system into a main socket, you must
check the voltage.
1
Plug the main lead (marked AC CORD on the rear of the
system) into an appropriate socket.
2
Press the On/Standby button to switch your Micro component
system on.
7
Downloaded From Disc-Player.com Samsung Manuals
GB
Connecting to an External Source
GB
The auxiliary input can be used to take advantage of the sound
quality of your MICRO component compact system when listening
to other sources.
Example:
A television
A video disc player
A Hi-Fi stereo video cassette recorder
To connect the external source, the source must have an
audio output. In addition, you need an RCA connection
cable.
1
2
Set the system to standby mode and disconnect it and the external
source from the main.
Connect the audio cable to the rear of the micro component
compact system.
Connect the...
To the connector marked...
Red jack
White jack
Connecting the Loudspeakers
The loudspeaker connector terminals are located on the rear of
the system.
There are four terminals on the system:
Two for the left speaker (marked L)
Two for the right speaker (marked R)
To achieve the correct sound quality, connect the:
Red wire to the + terminals
Black wire to the – terminals
1
2
3
4
To connect a wire to a terminal, push the tab as far as it will go:
To the right on the system
Insert the wire, up to the plastic sheathing, in the hole.
Push the tab back:
To the left on the system, until it clicks into place
To the top on the loudspeaker
Result: The wire is pinched and held firmly in place.
Repeat the operation for each wire.
R (right)
L (left)
For optimum sound quality, do not invert the right and left
channels.
3
Plug the system back into the main socket and press On/Standby
to switch it on.
4
Select the AUX function by pressing FUNC. button.
Result: AUX is displayed.
5
6
Switch the external source on.
(Right Speaker)
(Left Speaker)
Adjust the volume and balance as required:
Volume
Equalizer
CD Digital Out Jack
This unit can output CD digital sound signals through this jack.
Use an optical cable to connect digital audio equipment. (DAT
deck, MD recorder, etc.).
Remove the dust cap (1) from the CD DIGITAL OUT jack. Then,
connect an optical cable plug to the CD DIGITAL OUT jack.
Directions in Installing Speaker
◆ Installation in a place near heating apparatus, under direct lay
of light or with high humidity may cause performance
degradation of the speaker.
◆ Do not install on the wall or on a high place of pole or other
unstable place to prevent any safety accident caused by falling
of the speaker.
◆ Do not take the speaker apart from TV or computer monitor.
The speaker near the TV or computer monitor may influence
the quality of the screen display.
(1)
When the CD DIGITAL OUT jack is not being used
Attach the supplied dust cap.
8
Downloaded From Disc-Player.com Samsung Manuals
Connecting the AM (MW)/LW Aerial
The AM aerial (for long and medium waves) can be:
◆ Placed on a stable surface
◆ Fixed to the wall (you must first remove the base)
GB
The AM aerial connector terminals are located on the rear of the system and are marked AM.
To avoid noise interference, check that the loudspeaker wires do not run close to the aerial wires.
Always keep them at least 2 inches (5 cm) away.
Connecting the FM Aerial
How to connect a COAXIAL TYPE aerial.
◆ Connect a 75Ω antenna to the FM antenna terminal.
◆ Plug the connector on the FM aerial supplied into the coaxial socket (75Ω) marked FM on the rear of the system.
◆ Follow the instructions given on Page 12 to tune into a radio station, and determine the best position for the aerial.
◆ If reception is poor, you may need to install an outdoor aerial.
To do so, connect an outdoor FM aerial to the FM socket on the rear of the system using a 75Ω coaxial cable (not supplied).
9
Downloaded From Disc-Player.com Samsung Manuals
Setting the Clock
GB
Listening to a Compact Disc
Your system is equipped with a clock which allows you to turn
your system on and off automatically. You should set the clock:
When you purchase the Micro component system
After a power failure
After unplugging the unit
For each step, you have a few seconds to set the required
options. If you exceed this time, you must start again.
1
2
Switch the system on by pressing On/Standby.
Press Timer/Clock twice.
Result:
CLOCK is displayed.
This unit has been designed to playback the CDs: Audio CD, CD
Text, CD-R and CD-RW.
Continued use of irregular shape CDs (heart-shape, octagonal,
etc.) can damage the unit.
1
2
Select the CD function by pressing FUNC. button.
Press the Open/Close ( ) button on the front panel.
The compartment opens.
Result:
Place your disc in the compartment, with the label on the disc
facing upwards.
Close the compartment by pressing the Open/Close ( )
button again.
Result:
The display indicates the number of tracks
on the disc.
Press the PLAY/PAUSE (ˆ ¨) button.
Result:
The first track on the disc plays and the track
number is displayed.
To stop playback temporarily, press the PLAY/PAUSE (ˆ ¨)
button.
Press PLAY/PAUSE (ˆ ¨) again to continue playing
the disc.
Press the STOP (■) button when you have finished.
3
4
3
Press Program/Set.
Result:
The hour flashes.
4
To...
Press...
Increase the hours
Decrease the hours
ö
õ
5
5
When the correct hour is displayed, press Program/Set.
Result:
The minutes flash.
6
To...
Press...
Increase the minutes
Decrease the minutes
ö
õ
7
You can play 12 cm or 8 cm compact discs without an adapter.
6
7
When the correct time is displayed, press Program/Set.
Result:
The clock starts and is displayed, even when the
system is in standby mode.
2 4
You can display the time, even when you are using another
function, by pressing Timer/Clock once.
CD Door Open/Close
1
FUNC.
Volume
R
5 6
CD/TAPE/TUNING
Tuning Mode
Display
Repeat A B
CD Repeat
PTY
Band
7
Preset EQ
+10 (CD)
PROG./Set
CD Synchro
Start/Stop
Record
On/Standby
Sleep
Mute
Preset
EQ
Timer
on/off
Timer/
Clock
Tape
Mono/ST. Mode
Repeat
Program/
Set
1
Power
Sound
CD/TAPE/MP3
2
7
Band
5 6
Function
3 5 7
CD/TAPE/MP3
Band
When playing a CD-R or CD-RW
User-edited CD-Rs (Recordable) and CD-RWs (Rewritable)
can be played back only if they are already “finalized”.
Function
◆ You can play back your original CD-Rs or CD-RWs recorded
in music CD format. (However, they may not be played back
depending on their characteristics or recording conditions.)
VOL.
◆ Some CD-Rs or CD-RWs may not be played back on this unit
4 6
Tuning
Mode
VOL.
10
Downloaded From Disc-Player.com Samsung Manuals
4 6
because of their disc characteristics, damage or stain on them,
or if the player’s lens is dirty.
◆ CD-RWs may require a longer readout time. (This is caused
by the fact that the reflectance of CD-RWs is lower than for
regular CDs.)
Selecting a Track
CD Repeat Function
You can select the track you wish to listen to, either when the
compact disc player is stopped or when a disc is playing.
To start playback at the beginning of the...
You can repeat:
Press...
Next track ................................................. I once
Current track ............................................ I once
Previous track .......................................... I twice
Track of your choice ................................. I or I the appropriate
number of times.
FUNC.
1
2
Volume
R
CD/TAPE/TUNING
Tuning Mode
GB
A specific track on a compact disc
All tracks on the compact disc
Press the CD Repeat button.
To repeat the...
Press CD Repeat...
Current track indefinitely
Disc
Once (REPEAT 1 is displayed)
Twice (REPEAT ALL is displayed)
When you wish to cancel the Repeat function, press CD Repeat
a third time.
Result:
REPEAT is no longer displayed and the function is
cancelled.
Display
Repeat A B
CD Repeat
PTY
Band
Preset EQ
+10 (CD)
Power
Sound
Searching for a Specific Music Passage on a CD
Preset
EQ
Timer
on/off
Timer/
Clock
Tape
Mono/ST. Mode
Repeat
Program/
Set
1 2
When listening to a compact disc, you can quickly search for a
specific music passage on a track.
To search through the tracks...
CD/TAPE/MP3
Press and hold down...
Forwards .................................................. I for at least one second
Backwards ................................................ I for at least one second
It is recommended that you turn the volume down before using
this function.
Programming the Order of Playback
You can decide for yourself:
The order in which you listen to the tracks
The tracks to which you do not wish to listen
FUNC.
This feature can be combined with the Repeat function.
Volume
R
1
2
If necessary, stop the player by pressing STOP (■).
3
Select the required track by pressing the SKIP buttons:
I
to move backwards through the tracks
I to move forwards through the tracks
4
Press Program/Set.
Result:
P -- 0 2 is displayed.
To guarantee hours of enjoyable listening with your compact discs:
5
To select other tracks, repeat Steps 3 and 4.
Always hold them by the edges to avoid leaving
fingerprints on the shiny surface
6
When you have finished selecting the tracks, press CD (ˆ ¨)
to start listening to the selection, in the order in which the
tracks were programmed.
7
Press STOP (■) twice to cancel the selection when the disc is
playing.
CD/TAPE/TUNING
Tuning Mode
Display
Repeat A B
CD Repeat
PTY
Band
Preset EQ
+10 (CD)
Precautions When Using Compact Discs
You can programme up to 24 tracks.
Always replace them in their cases after listening to them
Do not fix paper or adhesive tape to the discs and do not
write on the label
Press Program/Set.
Result:
PROGRAM and P -- 0 1 are displayed.
Clean the player with a special cleaning disc
Tape
Mono/ST. Mode
Repeat
Program/
Set
1 7 CD/TAPE/MP36
3
Band
Function
2 4
3
11
Downloaded From Disc-Player.com Samsung Manuals
Checking and Changing Programmed Tracks
You can check and change your selection of tracks at any time.
GB
Searching for and Storing the Radio Stations
You can store up to:
15 FM stations
8 MW stations
7 LW stations
You must have selected at least one track.
1
Press STOP (■) once if you have started listening to the
selection.
2
Press Program/Set.
Each time you press Program/Set, the next selection
is displayed.
3
Press Program/Set one or more times until the track to be
changed is displayed.
4
5
Press SKIP I
or
1
2
Switch the system on by pressing On/Standby.
3
Select the required frequency band by pressing Band button.
Result:
The appropriate indication is displayed:
FM
Frequency Modulation
AM(MW)
Medium Wave
LW
Long Wave
4
To search for a
station...
Press Tuning Mode button
on the front panel....
Manually
One or more times until MANUAL is displayed.
One or more times until AUTO is displayed.
I to select the new track.
Press CD (ˆ ¨) to start listening to the selection.
Result:
The first track selected is played.
You can change one or more tracks in your initial selection.
Select the TUNER function by pressing FUNC. button.
Automatically
5
On/Standby
Sleep
Mute
Preset
EQ
Timer
on/off
Timer/
Clock
Tape
Mono/ST. Mode
Repeat
Program/
Set
Power
Sound
Select the station to be stored by:
Pressing Tuning õ or ö on the front panel
or
Pressing Tuning õ or ö on the remote control
To scroll through the frequencies faster when searching
manually, hold down the Tuning õ or ö buttons.
The automatic search procedure may stop on a frequency
that does not correspond to a radio station. If this happens,
use the manual search mode.
2 3
CD/TAPE/MP3
4
1
2
5
Band
Function
4
1
FUNC.
Volume
R
VOL.
5
CD/TAPE/TUNING
Tuning Mode
Tuning
Mode
3
Display
Repeat A B
CD Repeat
Band
Band
Preset EQ
PROG./Set
CD Synchro
4
PTY
+10 (CD)
Record
VOL.
12
Downloaded From Disc-Player.com Samsung Manuals
Start/Stop
5
Searching for and Storing the Radio Stations(continued)
6
Adjust the volume by:
Pressing Volume + or - on the front panel
or
Pressing the VOL. + or - buttons on the remote control
7
Select the stereo or mono mode by pressing Mono/ST.
Result:
The STEREO indicator is displayed when selected.
8
If you do not want to store the radio station found, revert to Step
4 and search for another station.
Otherwise:
a Press Program/Set.
Result: The program number and PROGRAM are displayed
for a few seconds.
b Press Tuning õ and ö to assign a program number
between 1 and 15.
c Press Program/Set to store the radio station.
Result: PROGRAM is no longer displayed and the station is
stored.
9
Selecting a Stored Station
You can listen to a stored radio station as follows:
GB
1
2
3
4
Switch the system on by pressing On/Standby.
Select the TUNER function by pressing FUNC. button.
Select the required frequency band by pressing Band button.
Select the radio station as follows.
To listen to ...
Press ...
A stored station
a Press the Tuning Mode button
until “PRESET” is displayed.
b Tuning õ and ö to select the
required program.
Tuning õ and ö until the
required frequency is displayed.
Another station
Press Tuning Mode again to exit the Preset Mode.
To store any other radio frequencies required, repeat Steps 3 to 8.
On/Standby
The PROGRAM function can be used to assign a new
station to an existing program number.
1Power
Sound
Power
Sound
Preset
EQ
Tape
Mono/ST. Mode
Timer
on/off
Timer/
Clock
Repeat
Preset
EQ
Tape
Mono/ST. Mode
Sleep
Mute
Timer
on/off
Timer/
Clock
Repeat
Band
Function
VOL.
4
Program/
Set
Tuning
Mode
4
4VOL.
CD/TAPE/MP3
Program/
Set
Band
3
2
Function
8
7
CD/TAPE/MP3
Band
Function
Improving Radio Reception
6
VOL.
VOL.
You can improve the quality of radio reception by:
Rotating the FM or AM(MW) aerial
Tuning
Mode
8
8
Testing the positions of the FM and AM(MW) aerials
before fixing them permanently
VOL.
VOL.
If reception from a specific FM radio station is poor,
press Mono/ST. to switch from stereo mode to mono.
The quality of the sound will be improved.
6
Power
Sound
Preset
EQ
Timer
on/off
Timer/
Clock
Tape
Mono/ST. Mode
Repeat
Program/
Set
FUNC.
6
Volume
R
CD/TAPE/TUNING
8
Tuning Mode
CD Repeat
Display
Repeat A B
8
CD/TAPE/MP3
PTY
Band
Preset EQ
+10 (CD)
PROG./Set
CD Synchro
Start/Stop
Record
Band
Function
13
Downloaded From Disc-Player.com Samsung Manuals
About RDS broadcasting
GB
About RDS DISPLAY function
This unit has the RDS (Radio Data System) function, which enables for
the various information such as broadcasting station, radio text, time and
30 types of programs (News, Rock, Classic, etc.) to be received from the
FM RDS station together with normal radio signal.
1
2
3
Press the On/Standby button.
Receive the FM radio.
See the radio receiving method on the page 12.
FM and frequency are shown on the display
If the received station transfers the RDS information, 'RDS'
appears automatically on the display.
Press the RDS Display button to select the desired RDS
mode.
Whenever the button is pressed, RDS mode changes as
follows.
About "PS NAME" MODE
Displays the name of broadcasting station.
Press the RDS Display button to select the PS NAME.
"PS NAME" appears on the display.
If the PS information is being received, the PS name (BBC, AFO,
NDR, etc.) is shown on the display.
If the PS information isn't received, the original FM frequency is shown.
Even though no RDS Display button is pressed, the reception
of PS information ensues the PS name is displayed.
Volume
R
CD/TAPE/TUNING
PS NAME
RT
CT
Current FM frequency
Tuning Mode
Display
Repeat
Repeat A
A B
B
CD Repeat
PTY
Band
Preset EQ
+10 (CD)
The RDS function is available only in FM broadcasting.
Record
PROG./Set
CD Synchro
Start/Stop
Description on RDS function
1. PTY(Program Type) : Displays the type of programme
currently being broadcast
2. PS NAME(Program Service Name) : Indicates the name of
broadcasting station and is composed of 8 characters.
3. RT(Radio Text) : Decodes the text broadcast by a station (if
any) and is composed of maximum 64 characters.
4. CT(Clock Time) : Decodes the real time clock from the FM
frequency.
Some stations may not transmit PTY, RT or CT
information therefore this may not be displayed in all
cases.
About 'RT' MODE
Displays the character transmitted from the
broadcasting station.
Press the RDS Display button to select the RT MODE.
"RT" appears on the display.
If the RT information is being received, the received information is
shown on the display.
If the RT information isn't received, the "NO RT" is shown.
On the display.
Volume
R
5. TA(Traffic Announcement) : When this symbol flashes it
shows that the traffic announcement is in progress.
CD/TAPE/TUNING
Tuning Mode
6. EON(Enhanced Other Networks Information) : Offers the
RDS information on other networks.
Display
Repeat A B
CD Repeat
PTY
Band
Preset EQ
+10 (CD)
Record
PROG./Set
CD Synchro
Start/Stop
About CT(Clock Time)
Sets the time of RDS clock.
To select the CT time, set the RDS Display button to CT MODE.
1
FUNC.
The CT information will take up to 2 minutes to be decoded
therefore the clock isn’t displayed immediately.
Volume
R
If there is no received CT information, "NO CT" is displayed.
CD/TAPE/TUNING
Tuning Mode
Display
Repeat A B
CD Repeat
PTY
Band
Preset EQ
+10 (CD)
Record
PROG./Set
CD Synchro
Start/Stop
Volume
R
CD/TAPE/TUNING
Tuning Mode
Display
Repeat A B
CD Repeat
PTY
Band
Preset EQ
+10 (CD)
Record
PROG./Set
14
Downloaded From Disc-Player.com Samsung Manuals
CD Synchro
Start/Stop
PTY(Program Type) indication and
PTY-SEARCH function
◆ The PTY information is composed of an identification symbol, which
helps the FM radio to recognize the program type of each FM
station.
◆ The below 30 PTY information is shown on the display by pressing
the Pty button.
About PTY-SEARCH
Searches the same PTY as the program type of broadcasting
station.
1
Program Type
Display
NEWS
• News including an announced opinion and report
AFFAIRS
• Several matters including a current incident, documentary,
discussion and analysis.
INFO
• Information including weights and measures, returns and forecast, matters interesting the customer, medical information, etc.
SPORT
• Sports
EDUCATE
• Education
DRAMA
• Drama-Radio serial, etc.
CULTURE
• Culture-National or local culture including the religious problem,
social science, language, theatre,etc.
SCIENCE
• Natural science and technology
VARIED
• Others-Speech, amusing program (quiz, game), interview,
comedy and satirical play, etc.
POP M
• Pop music
ROCK M
• Rock music
M.O.R.M
• M.O.R- Comfortable music, occasionally vocal or piece
LIGHT M
• Light classical music- Classical music and instrumental
and chorus music
CLASSIC
• Heavy classical music-Orchestra music, symphony, chamber
music and opera
OTHER M
• Other music - Jazz, R&B country music
WEATHER
• Weather
FINANCE
• Finance
CHILDREN
• Children’s programmes
SOCIAL A
2
Receive the FM radio.
See the radio receiving method on the page 8~9.
The FM and frequency appear on the display.
If the received station is transmitting the RDS information,
“RDS” lights up.
Press the PTY button.
The PTY MODE(NEWS, AFFAIRS, etc.) appears on the
display.
Press the TUNING õ or ö button to select the desired
PTY MODE.
If the station is transmitting no PTY information, 'NO PTY'
lights on the display.
When the PTY MODE is selected(The PTY MODE is
shown on the display), press the PTY KEY once again to
convert into PTY-SEARCH MODE and auto-search the
station sequentially.
If the PTY MODE received in the course of auto-search
agrees with the selected PTY MODE, the auto-search
stops and the PTY-SEARCH is finished.
If the PTY MODE which agrees with the PTY MODE selected in
the course of auto-search, isn't received, it is returned to the
first frequency at beginning the PTY SEARCH and the
auto-search and PTY SEARCH are suspended.
FUNC.
• Social affairs
Volume
2
R
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ
COUNTRY
NATIONAL M
OLDIES
FOLK M
DOCUMENT
TEST
• Religion
• Phone in
• Travel
• Leisure
CD/TAPE/TUNING
2
Tuning Mode
Display
Repeat A B
CD Repeat
PTY
Band
Preset EQ
+10 (CD)
PROG./Set
CD Synchro
Start/Stop
2
Record
• Jazz Music
• Country Music
• National Music
• Oldies Music
• Folk Music
• Documentary
• Alarm Test
15
Downloaded From Disc-Player.com Samsung Manuals
GB
Listening to a Cassette
GB
1
2
3
Selecting the Cassette Playback Mode
Switch the system on by pressing On/Standby.
Select the TAPE function by pressing FUNC. on the front panel.
Open the cassette deck by pushing on the corner of the cover
marked Push Eject until you hear a click and then releasing it.
Insert the pre-recorded cassette with the open edge of the
tape facing downwards.
Close the deck by pushing on it until it clicks into place.
4
5
6
To listen to...
Side A
Side B
Result:
7
Your micro audio system has three cassette playback modes which
enable you to listen to both sides of a cassette automatically.
You can select this function during playback or when the
cassette is stopped.
Press Tape Mode one or more times to display the required symbol.
When the display
indicates...
One side of the cassette and then stops.
Press...
One side of the cassette
The other side of the cassette and then stops
ˇ ˆ Once
ˇ ˆ Again
The cassette starts playing.
To...
Both sides of the cassette indefinitely (both sides
are played one after the other until you stop the
player).
Press...
Adjust the volume
VOL. + or – (or the
Volume + or – buttons
on the front panel)
Stop the playback or search
STOP (■)
When the cassette is stopped, select one of the following
functions as required.
8
The system plays back...
To...
Power
Sound
Preset
EQ
Timer
on/off
Timer/
Clock
Tape
Mono/ST. Mode
Repeat
Program/
Set
CD/TAPE/MP3
Press...
Rewind the cassette
Fast-forward the cassette
Band
Function
The cassette player stops automatically when the
beginning or end of the cassette is reached.
Maintaining the Sound Quality
2
1
3
FUNC.
7
Volume
6
R
◆
◆
◆
CD/TAPE/TUNING
Tuning Mode
Display
Repeat A B
CD Repeat
7
PTY
Band
Preset EQ
PROG./Set
CD Synchro
+10 (CD)
Record
Mono/ST. Mode
Repeat
Start/Stop
Roller (②)
Drive capstan (③)
To guarantee hours of enjoyable listening with your cassettes:
◆
◆
◆
Set
Heads (①)
Check that the tape in the cassette is always sufficiently taut.
Store your cassettes in a clean place, out of direct sunlight,
where they will not be exposed to high temperatures.
Avoid using 120-minute cassettes as they are extremely fragile.
VOL.
VOL.
8
Band
CD/TAPE/MP3
7
8
7
3
3
Tuning
Mode
Function
7
VOL.
VOL.
2
16
Downloaded From Disc-Player.com Samsung Manuals
1
2
Repeat (A↔B) Function
Recording a Radio Programme
You can record a radio programme of your choice and listen to it
at a later date.
GB
When you select CD(TAPE) Repeat (A↔B) playback, the music
passages to which you were listening is repeated 3 times.
1
Insert a blank cassette in the cassette deck.
2
Select the TUNER function by pressing FUNC. button.
3
Select the radio station that you wish to record by pressing
Tuning õ or ö .
4
To start recording, press the Record Start/Stop button.
Result:
Recording starts immediately.
5
When you wish to stop recording, press the Record Start/Stop
button.
1
Press CD(ˆ ¨) / TAPE(ˇ ˆ ) button.
Result:
The CD(TAPE) player starts playing.
2
Press Repeat (A↔B) button.
Result:
The indications appear: START
The flashes appear: A↔B
A Time is memorized.
3
Press Repeat (A↔B) button.
Result:
The indications appear: END
B Time is memorized.
Your selected passages are repeated 3 times.
4
When you want to cancel the Repeat playback,
Press Repeat (A↔B).
CD/TAPE/MP3
2
FUNC.
5
FUNC.
Band
Function
Volume
Volume
R
3
Tuning Mode
R
3
CD/TAPE/TUNING
CD/TAPE/TUNING
VOL.
3
Display
Repeat A B
CD Repeat
3
1
Tuning Mode
Display
Repeat A
A B
B
Repeat
CD Repeat
PTY
PTY
Band
Preset EQ
Tuning
Mode
+10 (CD)
Record
PROG./Set
CD Synchro
Band
Preset EQ
+10 (CD)
2 3 4
Record
PROG./Set
CD Synchro
Start/Stop
Start/Stop
4 5
VOL.
Recommendations for Recording
Recording a CD with the CD Synchro Feature
You can record a compact disc on a cassette.
1
Insert a blank cassette in the cassette deck.
2
Select the CD function by pressing FUNC. button.
3
Load a compact disc.
4
Press the CD Synchro button.
Result:
The first track on the disc is played and the player
starts recording automatically (synchronised
recording).
5
When you have finished recording, press the STOP (■) button.
Record on normal bias cassettes only.
To prevent erasing a cassette that you wish to keep,
remove the safety tabs on the upper edge of the
cassette. To re-record a cassette, where the tabs have
been broken, simply cover the openings with
adhesive tape.
It is an infringement of copyright laws to copy
records and pre-recorded cassettes or to re-record
them in any form without the permission of the
owners of the corresponding copyright.
2
FUNC.
Volume
R
CD/TAPE/TUNING
Tuning Mode
Display
Repeat A B
CD Repeat
5
PTY
Band
4
PROG./Set
Preset EQ
+10 (CD)
Record
CD Synchro
Start/Stop
17
Downloaded From Disc-Player.com Samsung Manuals
Timer Function
GB
The timer enables you to switch the system on or off at specific times.
Example: You wish to wake up to music every morning.
If you no longer want the system to be switched on or off
automatically, you must cancel the timer.
On/Standby
Before setting the timer, check that the current
time is correct.
For each step, you have a few seconds to set
the required options. If you exceed this time,
you must start again.
1
2
3
4
5
6
7
Mute
Preset
EQ
Timer
on/off
Timer/
Clock
Tape
Mono/ST. Mode
Repeat
Program/
Set
1 8
Power
Sound
Switch the system on by pressing On/Standby.
Press Timer/Clock until
Set the timer switch-on time.
a Set the hour by pressing Tuning õ and ö .
b Press Program/Set.
The minutes flash.
Result:
c Set the minutes by pressing Tuning õ and ö .
d Press Program/Set.
Result: OFF TIME is displayed (instead of the equalizer
symbols) for a few seconds, followed by any
switch-off time already set; you can now set the
timer switch-off time.
Set the timer switch-off time.
a Set the hour by pressing Tuning õ and ö .
b Press Program/Set.
Result: The minutes flash.
c Set the minutes by pressing Tuning õ and ö .
d Press Program/Set.
Result: VOL XX is displayed, where XX corresponds to
the volume already set.
Press Tuning õ and ö to adjust the volume level and press
Program/Set.
Result:
The source to be selected is displayed.
Press Tuning õ and ö to select the source to be played
when the system switches on.
If you select...
You must also...
TAPE (cassette)
Insert a recorded cassette in one of
the decks before setting the system
to standby.
a Select the FM or AM frequency
band by pressing Tuning Mode
õ and ö .
b Press Program/Set.
c Select a preset station by pressing
Tuning Mode õ and ö .
a Load a compact disc.
CD (compact disc)
Press On/Standby to set the system to standby mode.
is displayed to the bottom left of the time, indicating
Result:
that the timer has been set. The system will switch on
and off automatically at the required times.
If the timer switch on and off times are identical, the word
ERROR is displayed.
18
Downloaded From Disc-Player.com Samsung Manuals
2
3 4 5 6 7
TIMER is displayed.
CD/TAPE/MP3
Press Program/Set.
Result:
ON TIME is displayed (instead of the equalizer
symbols) for a few seconds, followed by any
switch-on time already set; you can set the timer
switch-on time.
TUNER (radio)
8
Sleep
Band
Function
VOL.
4 5 6 7
4 5 6 7
Tuning
Mode
VOL.
Cancelling the Timer
After having set the timer, it will start automatically as shown by
the
indication on the display. If you no longer wish to use the
timer, you must cancel it.
You can cancel the timer at any time (system on or in standby
mode).
To...
Cancel the timer
Press Timer On/Off...
Once.
is no longer displayed.
Result:
Restart the timer
Twice.
Result:
On/Standby
is displayed again.
Sleep
Mute
Preset
EQ
Timer
on/off
Timer/
Clock
Tape
Mono/ST. Mode
Repeat
Program/
Set
Power
Sound
CD/TAPE/MP3
Setting the System to Switch Off Automatically
While listening to a compact disc or a cassette, you can set the
system to switch off automatically.
Example: You wish to go to sleep to music.
1
Press Sleep.
Result: The following indications are displayed:
2
Press Sleep one or more times to indicate how long the
system should continue playing before it switches off:
90 MIN
OFF
3
60 MIN
15 MIN
45 MIN
30 MIN
At any time, you can:
Check the remaining time by pressing Sleep.
Change the remaining time by repeating steps 1 and 2.
To cancel SLEEP function, press Sleep one or more times
until OFF is displayed.
On/Standby
Equalizer
Your micro audio system is equipped with a preset equalizer that
enables you to choose the most appropriate balance between treble
and bass frequencies, according to the type of music to which you
are listening.
Press the Preset EQ button one or more times until the required option
is selected.
To obtain a...
Select...
Standard balance (linear)
PASS
Balance suitable for Dance club
Balance suitable for Hall
Dl CLUB
HALL
Balance suitable for Stadium
Balance suitable for rock music
Balance suitable for pop music
STADIUM
ROCK
POP
Balance suitable for classical music
CLASSIC
Result: The corresponding indication is displayed.
FUNC.
Sleep
Mute
Volume
R
CD/TAPE/TUNING
1 2 3
Power
Sound
Preset
EQ
Timer
on/off
Tuning Mode
Timer/
Clock
Display
Repeat A B
CD Repeat
PTY
Band
Tape
Mono/ST. Mode
Repeat
Program/
Set
Preset
PresetEQ
EQ
+10 (CD)
Record
PROG./Set
CD Synchro
Start/Stop
Mute Function
You can turn the sound off temporarily on your system.
Example: You wish to answer a telephone call
1
2
Press Mute.
To switch the sound back on(at the same volume as before),
press Mute again or the Volume buttons.
On/Standby
Sleep
Mute
Preset
EQ
Timer
on/off
Timer/
Clock
Tape
Mono/ST. Mode
Repeat
Program/
Set
1
Power
Sound
19
Downloaded From Disc-Player.com Samsung Manuals
GB
Power Sound function
GB
This machine is equipped with the function of Power Sound which
amplifies bass treble output to twice as much for powerful real
sound.
Connecting Headphones
You can connect a set of headphones to your micro component
system so that you can listen to music or radio programs without
disturbing other people in the room. The headphones must have a
3.5 mm connector or appropriate adapter.
1
Press the Power Sound button.
Result:
P, SOUND is displayed for a few seconds.
A more powerful resonant sound is diffused.
Connect the headphones to the Phones connector on the front panel
(bottom left corner).
2
To cancel this function, press Power Sound button again.
Result: The loudspeakers are no longer used for sound output .
Prolonged use of headphones at a high volume may damage
your hearing.
On/Standby
Sleep
Mute
Preset
EQ
Timer
on/off
Timer/
Clock
Tape
Mono/ST. Mode
Repeat
Program/
Set
Power
Sound
20
Downloaded From Disc-Player.com Samsung Manuals
Safety Precautions
Before Contacting the After-Sales Service
The following diagrams illustrate the precautions to be taken
when using or moving your Micro component system.
10%
It always takes a little time to become familiar with a new appliance.
If you have any of the problems listed below, try the solutions given.
They may save you the time and inconvenience of an unnecessary
service call.
75%
35°
Problem
H
Checks/Explanation
H
5°
FUNC.
Volume
FUNC.
R
CD/TAPE/TUNING
Tuning Mode
Repeat
Volume
R
Display
CD/TAPE/TUNING
Repeat A B
PTY
Tuning Mode
Band
Preset EQ
+10 (CD)
PRO./Set
CD Synchro
Star/Stop
Repeat
Display
Repeat A B
Record
PTY
Band
Preset EQ
+10 (CD)
PRO./Set
CD Synchro
Star/Stop
Record
Ambient operating conditions:
Ambient temperature
5°C-35°C
Humidity
10-75%
Do not expose the unit to direct sun
radiation or other heat sources.
This could lead to overheating and
malfunction of the unit.
G
E
N
E
R
A
L
The system does not work
• The power cord is not correctly plugged into a wall
socket or the wall socket is not switched on.
• The remote control batteries need replacing or
the polarity has not been respected.
• The On/Standby button has not been pressed.
There is no sound
• The volume has been completely turned down.
• The correct function (TUNER, CD, TAPE, AUX)
has not been selected.
• You have connected a set of earphones.
• The loudspeaker wires have been disconnected.
The Timer does not work
• The timer has been stopped by pressing Timer
On/Off.
Incase it is not worked, even
the action is taken as above.
Press the Preset EQ button on the front
Panel for 5 seconds in power ‘OFF’(standby), then it is returned the original position
(RESET).
The compact disc player does not
start playing
• The CD function has not been selected.
• The disc has been inserted face down or is either
dirty or scratched.
• The laser sensor is dirty or dusty.
• The system has not been installed on a flat, horizontal surface.
• Condensation has formed in the player; leave the
system in a warm, airy room for at least one hour.
C
FUNC.
FUNC.
D
Volume
Volume
R
R
CD/TAPE/TUNING
CD/TAPE/TUNING
Tuning Mode
Tuning Mode
Repeat
Display
Repeat
Display
Repeat A B
Repeat A B
PTY
PTY
Band
Preset EQ
+10 (CD)
PRO./Set
CD Synchro
Star/Stop
Band
Preset EQ
+10 (CD)
PRO./Set
CD Synchro
Star/Stop
Record
Record
Do not place potted plants or vases on
top of the unit. Moisture entering the
unit could lead to dangerous electric
shock and cause equipment damage.
In such events immediately disconnect
the power cord from the socket.
During thunderstorms, disconnect
the power cord from the socket.
A voltage surge due to lightning
could damage the unit.
VOLUME
Remove the batteries from the
remote control, if not used for any
extended periods.
Leaking batteries can cause serious
damage to the remote control.
When using headphones, take care
not to listen at excessive volumes.
Extended use of headphones at
high volumes will lead to hearing
damage.
C
A
S
S
E
T
T
E
S
R
A
D
I
O
The tape does not start playing
The volume falls off
The cassette is not erased correctly
There is excessive wow and flutter
• The TAPE function has not been selected.
• The cassette has not been inserted correctly.
• The cassette player has not been closed.
• The tape is either slack or broken.
• The audio heads are dirty.
• The rollers or drive capstans are dirty.
• The tape is worn.
Reception is poor or no radio stations • The TUNER function has not been selected.
are received at all
• The radio frequency has not been correctly
selected.
• The aerial has been disconnected or is not facing
the right way. Turn it until you find the best orientation.
• You are in a building that blocks radio waves; you
must use an outside aerial.
If the above guidelines do not allow you to solve the problem, take
a note of:
The model and serial numbers, normally printed on
the rear of the system
Your warranty details
A clear description of the problem
Then contact your local dealer or SAMSUNG after-sales service.
FUNC.
Volume
R
CD/TAPE/TUNING
Tuning Mode
Repeat
Display
Repeat A B
PTY
Band
Preset EQ
+10 (CD)
PRO./Set
CD Synchro
Star/Stop
Record
Do not place heavy items on the
power cord. Power cord damage
can lead to damage of the
equipment (fire hazard) or cause
electric shock.
Do not remove any equipment panels.
The inside of the unit contains live
components, which cause electric
shock.
21
Downloaded From Disc-Player.com Samsung Manuals
GB
Technical Specifications
GB
SAMSUNG strives to improve its products at all times. Both the design specifications and these user
instructions are thus subject to change without notice.
RADIO
LW
Usable sensitivity
FM
Signal/noise ratio
Usable sensitivity
Total harmonic distortion
AM (MW)
Signal/noise ratio
Usable sensitivity
Total harmonic distortion
60 dB
60 dB
6 dB
1.5%
40 dB
54 dB
2%
COMPACT DISC PLAYER
Frequency range
Signal/noise ratio
Distortion
Channel separation
Disc sizes
20 Hz - 20 KHz (±54 dB)
90 dB (at 1 KHz) with filter
16-bit
Outside measurable limits
Diameter: 120 or 80 mm. Thickness: 1.2 mm
TAPE DECK
Frequency range
Signal/noise ratio
Channel separation
Erasing effect
125 Hz ~ 12 KHz
40 dB
35 dB
60 dB
GENERAL
Output power
Dimensions
2x20 Watts (total harmonic distortion:10%)
180(W)x265(H)x270(D)mm.
22
Downloaded From Disc-Player.com Samsung Manuals
THIS APPLIANCE IS MANUFACTURED BY:
ELECTRONICS
AH68-00770B
Downloaded From Disc-Player.com Samsung Manuals
Download PDF

advertising