Automatic Technology | GDO-7v2 SecuraLift | Troubleshooting guide | Automatic Technology GDO-7v2 SecuraLift Troubleshooting guide

GDO-7v2 SecuraLift®
Overhead Garage Door Opener
Featuring TrioCode™ Technology
Part # 13215 (Manual)
INSTALLATION INSTRUCTIONS | OWNERS COPY
WARNING: It is vital for the safety of persons to follow all
instructions. Failure to comply with the installation instructions
and the safety warnings may result in serious personal injury
and/or property and remote control opener damage. Please
save these instructions for future reference.
Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all
conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of
an Automatic Technology Australia Pty Ltd Garage Door Opener. Automatic Technology Australia Pty Ltd hereby further
expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any person as a
result whether directly or indirectly from failure to install the Automatic Technology Australia Pty Ltd Garage Door Opener
in accordance with these installation instructions.
2
GDO-7v2 SecuraLift® Owner Installation Instructions
GDO-7v2 SecuraLift®
Overhead Garage Door Opener
Important Safety Instructions
Features
Operating Controls
Package Contents
Installation
Tube Rail Assembly
Determine the Door Type
Mounting on a Track Type Door
Mounting on a non-Track Type Door
Mounting Door Bracket & Arms
Programming the Opener
Setting Limits
Setting Limits: via Transmitter
Safety Obstruction Force
Safety Obstruction Force Test
Adjustin Safety Obstruction Forces
Coding Transmitters
Door
Courtesy Light
Vacation Mode
Pet (Pedestrian)Mode
Remotely Coding Transmitters
Deleting Transmitter Codes
Accessories
Photo Electric Beam
Auto-Close
Final Set Up
Courtesy Light Time
Pet Mode Door Height
Wall Mounted Transmitter
Re-Initialising
Parameters
Door Status Indicators
Button Functions
System Specifications
Troubleshooting Guide
Maintenance
Spare Parts
Warranty
Owner Installation Instructions GDO-7v2 SecuraLift®
4
6
8
10
11
11
12
13
14
15
16
16
17
18
18
19
20
20
20
20
20
21
21
22
22
22
23
23
23
23
23
24
24
25
26
27
28
29
30
3
Important Safety Instructions
WARNING: It is vital for the safety of persons to follow
all instructions. Failure to comply with the following
Safety Rules may result in serious personal injury and/or
property damage.
CAUTION: If your garage has no pedestrian entrance door, an emergency access device should be installed.
This accessory allows manual operation of the garage door from outside in case of power failure.
For ADDITIONAL SAFETY protection we STRONGLY recommend the fitting of a Photo Electric (P.E.)
Beam. In most countries P.E. Beams are mandatory on all garage doors fitted with automatic openers.
For a small additional outlay Automatic Technology recommends that Photo Electric Beams be
installed with the automatic opener ensuring additional safety and peace of mind.
DO NOT operate the opener unless the garage door is in full view and free from objects such
as cars and children/people. Make sure that the door has finished moving before entering or
leaving the garage.
DO NOT operate the opener when children/persons are near the door. Children must be
supervised at all times when the SecuraLift® is in use. Serious personal injury and/or
property damage can result from failure to follow this warning.
DO NOT allow children to operate the SecuraLift®. Serious personal injury and/or
property damage can result from failure to follow this warning.
Regularly check to make sure that the safety obstruction force is working
correctly, and is tested and set as per page 18 of this manual. Failure to
follow these instructions could result in serious personal injury and/or
property damage. This test must be repeated at regular intervals and the
necessary adjustments made as required.
Doors requiring over 400N of force to move must have P.E. Beams
installed.
DO NOT disengage the door opener to manual operation with
children/persons or any other objects including motor vehicles
within the doorway.
The door opener is not intended for use by young children
or infirm persons without adequate supervision. Children
should be supervised to ensure that they do not play
with the remote transmitters or the opener.
Keep hands and loose clothing clear of the door
and door opener at all times.
4
GDO-7v2 SecuraLift® Owner Installation Instructions
Important Safety Instructions
The unit should be installed so that it is protected from the elements. It should not be exposed to water or rain.
It is not to be immersed in water or sprayed directly by a hose or other device.
The garage door must be well balanced. Sticking or binding doors must be repaired by a qualified garage
door installer prior to installation of the opener.
Frequently examine the installation, in particular cables, springs and mountings for signs of wear,
damage or imbalance. DO NOT use if repair or adjustment is needed since a fault in the installation
or an incorrectly balanced door may cause injury. DO NOT attempt to repair the door yourself as
hardware is under extreme tension.
Remove or disengage all garage door locks and mechanisms prior to installation of the opener.
Connect the opener to a properly earthed general purpose 240V mains power outlet
installed by a qualified electrical contractor.
Disconnect the power cord from mains power before making any repairs or removing
covers. Only experienced service personnel should remove covers from the opener.
When using auto close mode, a photo electric beam must be fitted correctly and
tested for operation at regular intervals. Extreme caution is recommended when
using auto close mode. All safety rules must be followed.
In order for the SecuraLift® to sense an object obstructing the door way,
some force must be exerted on the object. As a result the object, door
and/or person may suffer damage or injury.
If the power supply cord is damaged, it must be replaced by an
Automatic Technology service agent or suitably qualified person.
Make sure that the door is fully open before driving in or out of
the garage and fully closed before leaving the driveway.
Make sure that remote controls are kept out of reach of
children.
Install the wall switch or wall mounted transmitter in a
location where it is out of reach of children and the
garage door is visible. We recommend that the wall
control be fixed at a hight of at least 1.5 metres
and within sight of the door but away from
moving parts.
Owner Installation Instructions GDO-7v2 SecuraLift®
5
Features
Thank you for purchasing the Automatic Technology
SecuraLift® Automatic Garage Door Opener.
Designed by our renowned engineers to suit sectional
overhead and one piece tilt up doors, the SecuraLift®
will provide years of smart, simple & secure
convenience to your home.
Operation
To open or close the door simply press a button on a TrioCode™ handheld
transmitter, a wall mounted transmitter, or optional wall switch for two seconds.
During open and close cycles the door can be stopped by pressing the button
again. The next actuation will move the reverse the door’s direction.
TrioCode™ Code Hopping Multi-Frequency Technology
Every time a TrioCode™ transmitter is used a new security code is randomly
generated from over 4.29 billion possibilities. This greatly enhances the security of
the system and makes “code grabbing” a thing of the past
These transmitters also overcome interference issues by simultaneously sending a
signal over three slightly different frequencies. Even if two of the three signals are
jammed, the system will still work.
S-ALPS (Semi Automatic Limits Positioning System)
The S-ALPS system does away with manual adjustment of the door’s limits position
using mechanical parts, such as cams and microswitches. During installation the handheld
transmitter can be programmed to set the limits positions.
Anti-travel electronic brakes
The SecuraLift® features an anti-travel electronic brake mechanism to ensure the opener stops the door
at exact location
ISS (intelligent safety obstruction system)
While the door is performing a close cycle, should it hit an obstacle or be restricted in some manner, it
will automatically reverse. The amount of force the door should encounter before reversing is automatically
adjusted by the doors control system during the initial installation of the automatic door opener. The door will
also stop if restricted whilst opening. The Safety Obstruction Force should be checked at least once a month.
See installation manual for instructions.
6
GDO-7v2 SecuraLift® Owner Installation Instructions
Overload indicator
When the maximum opening and closing capacity of the SecuraLift® is exceeded
the red and green Limits LEDs flash alternately to indicate that an overload has
occurred.
Auto courtesy light
The SecuraLift® courtesy light comes on automatically whenever the door is
activated. The light can also be switched on and off without operating the door
by coding a dedicated button on a TrioCode™ transmitter. The light will stay on
for approximately three minutes then switch off. This time is adjustable.
Vacation mode
A hand held transmitter can be programmed to lock and unlock all other
transmitters that have been programmed into the openers’ memory. The vacation
mode can be used when the door is left idle for long periods of time.
Pet/Pedestrian mode
The hand held transmitter can be programmed to open the door partially so that the
family pet can enter and exit the garage at any time. You may also wish to open the
door to a height suitable only for pedestrian access. The door opening position is also
programmable.
Auto-close mode
The opener can be programmed to automatically close after an open cycle. The auto-close time
is adjustable. It is compulsory to install a P.E. Beam if this mode is selected, otherwise the door may
cause personal injury or damage to property.
Photo Electric (P.E.) Beam (optional)
The opener has an input to connect a P.E. Beam for extra safety and use of the auto-close mode. We highly
recommend that Photo Electric Beam be installed.
Manual operation
The opener is equipped with a unique manual disengaging device. If the power to the opener is disrupted for
any reason the door can be put into manual mode by pulling down on the string handle on an angle towards
the door. This will allow you to manually open or close the door. To re-engage the opener pull the string
Owner Installation Instructions GDO-7v2 SecuraLift®
7
Operating Controls
01
02
PROG (Input) is used to connect he Automatic Technology Handheld Programmer PG-3 for editing
control and receiver functions, accessing diagnostic, and activating special features and operating
modes.
Terminal Block (J6).
•
•
•
•
30V PWR is used to power devices such as:
Photo electric beam (PE-2) for safety and auto-close function (P.E. and P.E.(0V) terminals).
GND - Common ground for accessories.
OSC is used for the connection of a wired switch (momentary contact). This switch can then
be used to open, stop or close the door. Install the wall switch in a location where the switch is out of
reach of children and the garage door is visible.
AUX (open collector outout) - A transmitter button can be programmed to trigger an input.
03
SET button (yellow) is used during the installation phase together with the Open and Close buttons to set
04
OPERATE button (Yellow) is used during installation to test the open, stop and close cycles for the
opener. The opener has to be initialised by the Reset button to make the O/S/C button operable.
05
PLUS (+) button (green) is used during installation to help set the open limit position. Pressing and
holding this button will move the door in the open direction, releasing stops the door.
NOTE: The safety obstruction detection is inoperable when the PLUS (+) button is used to move door.
06
OPEN LIMIT LED (green) the LED is very helpful during installation. It illuminates and flashes when the
the door limit positions. The Set button is also used to re-initialize the Opener.
door is opening and remains steady on when the open limit position has been reached.
FORCE MARGIN SET Button The obstruction force margin is set automatically during installation. The
8
07
margin can be adjusted manually using the Force Margin Set button (White). Holding the Force Margin Set
button and pressing Plus (+) or Minus (-) buttons will increase or decrease the amount of force. The Force
Margin Set should only be used if environmental factors (wind, etc.) affect the door’s operation.
08
LIGHT CODE button (white) is used for storing or erasing the transmitter button (code) you wish to use
09
CODING LED (red) light flashes when a code is being stored or when a transmitter button is pressed.
10
DOOR CODE BUTTON (blue) is used for storing or erasing the transmitter button you wish to use to
11
DOOR STATUS LED (Yellow)
12
MINUS (-) button (red) is used during installation to help set the close limit position. Pressing and holding
this button will move the door in the close direction. Movement stops when the button is released.
NOTE: The safety obstruction detection is inoperable when the MINUS (-) button is used to move door..
13
CLOSE LIMIT LED (red) the LED is very helpful during installation. It illuminates and flashes when the
door is closing and remains steady on when the close limit position has been reached.
14
DATUM ADJUST SCREW is used during limits set up to indicate the mid point of the door’s travel.
15
AUTO CLOSE TIME button (White) is used to adjust the auto close time. While holding in the AUTO
CLOSE TIME button and then pressing the open button the time is increased. Each press will increase the
time by 5 seconds. Pressing the close button will decrease the time.
to switch the courtesy light on the opener on or off.
command the door to open, stop or close.
GDO-7v2 SecuraLift® Owner Installation Instructions
01
02
J4
04
03
08
05
10
09
12
11
06
13
07
15
14
Owner Installation Instructions GDO-7v2 SecuraLift®
9
Package Contents
GDO-7V2 Securalift® drive unit
1
TrioCode keyring transmitters
2
TrioCode wall mounted transmitters (not available all models)
1
Tubes
5
Tube inserts
4
Pipe adapter
1
Chain
1
Shuttle assembly
1
Door attachment arms
2
Hardware pack
1
Installation Manual
1
™
™
10
GDO-7v2 SecuraLift® Owner Installation Instructions
Tube Rail Assembly
IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION
Warning: Incorrect installation can lead to severe injury.
Follow ALL installation instructions.
Step 1 - Assembling Rail
NOTE: Arrow on shuttle must point towards the
door.
a.
b.
c.
d.
e.
Slide the shuttle assembly onto the long tube with a
hole. Match the holes on the tube and the shuttle and
hold the two in position with a screwdriver (Fig. 01).
Position the long tube with affixed shuttle assembly
in the intended centre of the finished rail.
Slide insert tubes halfway into each end of long tube.
Slide another long tube onto the protruding inserts
Continue this process, adding the same number of
long tubes either side of the centre assembly, until
the desired length is achieved.
At the door end of the finished rail, attach the pipe
adapter assembly (Fig. 02).
fig 01
fig 02
Step 2 - Assembling Chain
NOTE: If fitting to a one piece door without track, the
supplied 8-tooth drive sprocket must be replaced
with a 7-tooth version (available seperately).
a.
b.
c.
Pipe adapter
Attach one end of chain to the chain index screw
nearest to powerhead using one joint link. (Fig. 01).
Wrap chain around powerhead sprocket and chain
spreader (Fig. 03), then follow along the pipe to the
idler wheel on support pipe assembly,
Attach chain to the other chain index screw (Fig. 01).
fig 03
NOTE: Make certain that drive sprocket’s teeth
are engaged in the chain and that the chain is not
twisted. Make sure that the chain is engaged in
both the chain spreader and the support pipe
assembly’s idler wheel (Fig. 03)
Step 3 - Tensioning Chain
a.
b.
c.
d.
e.
f.
Disengage trolley from chain index by pulling lever
downward (Fig. 04)
Slide trolley along the rail away the chain index.
Loosen locking nuts on chain index screws.
To tighten chain, turn chain index in anticlockwise
direction (looking down towards powerhead end)
DO NOT OVERTIGHTEN CHAIN - it must have
approximately 6 to 12mm of sag.
Ensure the chain is not twisted before tightening nuts.
When the tension is finalised, tighten lock nuts at
both ends of chain index.
Locking nuts
Shuttle
assembly
fig 04
Disengaged
position
Engaged
position
Owner Installation Instructions GDO-7v2 SecuraLift®
11
Determine the Door Type
Step 4 - Determine Door Type
Determine which type of garage door you have as
illustrated below. (Fig. 05 to 07).
For a sectional (panel) door on tracks (Fig. 05)
proceed with the installation from Step 5.
Track
fig 05
Door
Sectional door with track
For a one-piece door on tracks (Fig. 06)
proceed with the installation from Step 5.
fig 06
One piece door with
track
For a one-piece door without tracks (on springs) (Fig. 07)
proceed with the installation from Step 9.
Door
fig 07
One piece door
without track
12
GDO-7v2 SecuraLift® Owner Installation Instructions
Mounting on a Track Type Door
Step 5 - Determine Bracket Position
a.
b.
c.
Open the door and find the highest point of travel of
the top door panel.
Using a level, transfer this height to the wall above
the door (Fig. 08) and mark a line 60mm above it.
Determine the centre point on the wall above and on
top of the door. Draw two lines extending 21.5mm
from each side of the centre point. (Fig. 09)
Level
Level
Track
Track
fig 08
Door
Door
Step 6 - Mounting the Wall Bracket
a.
b.
c.
Centre the bracket over the intersection of these two
lines. Mark centres for at least two holes (Fig. 09).
Ensure this is into a solid mounting point
•
Drill holes into the wall with an appropriate bit.
Secure to the wall using:
IF CONCRETE OR BRICK - 8mm or 5/16 loxins or
dynabolts.
IF TIMBER - wood screw #20 or equivalent
(minimum 50mm long).
fig 09
WARNING: Make sure concrete, brick wall or
timber lintels are solid and sound so as to form a
secure mounting platform.
Drilled holes
Step 7 - Attach the Rail to the Wall Bracket
a.
b.
Attach the tube rail assembly to the wall bracket
with the 90mm long clevis pin and secure with the
supplied snap pin (Fig. 10)
Leave the powerhead in its packing box for protection
during installation.
Step 8 - Secure the Powerhead to the Ceiling
a.
b.
c.
d.
e.
Raise the powerhead from the packing box and
support it in the horizontal position with a step
ladder.
Open the garage door. Rest the opener on the open
door and use a scrap piece of wood to bring it to
horizontal level.
Line up the track perpendicular to the wall.
Secure the perforated angle (not supplied) to
the ceiling above where powerhead’s mounting
holes will be once fully installed. A representative
mounting is shown (Fig. 11)
Connect the powerhead to the ceiling mounted
perforated angle with M8x20mm screws and nuts.
Strips should not extend more than 18mm below
centre of powerhead mounting holes.
fig 10
Go to Step 14 on page 14.
fig 11
WARNING: The opener must be securely
fastened to structural supports otherwise opener
failure may ensue, causing serious personal injury
and/or property damage.
Owner Installation Instructions GDO-7v2 SecuraLift®
13
Mounting on a non-Track Type Door
WARNING: Make sure concrete, brick wall or
timber lintels are solid and sound so as to form a
secure mounting platform.
Centre of Door
Step 9 - Determine the Door’s Centre
fig 12
a.
b.
Find the centre of the door and mark this location
both above the door and on top of the door.
Draw two lines 21.5mm either side of this (Fig. 12).
Step 10 - Prepositioning the Opener
a.
b.
c.
Raise the door to open position.
Rest the opener on the top edge of the door with
end of the rail against the wall (Fig. 13).
Support the powerhead level with the lowest point
of the open door (Fig. 13).
NOTE: Do not slide rail along the face of the door.
fig 13
Step ladder
Step 11 - Mounting the Tube Rail
a.
b.
c.
d.
e.
f.
Tube
highest
point
of door
travel
25mm
fig 14
g.
Door
Step ladder
h.
Close the door slowly. The rail will be elevated by
the top edge of the door as it moves.
Stop the door when it is at its highest point of travel.
Allow 25mm additional height for clearance between
the door and the track (Fig. 14).
Support the Rail in this position and close the door
The height determined in Step 11(b) will be the
height at which to mount the wall bracket.
Centre the bracket along the line detemined in Step
9
Using the bracket as a template, mark a minimum of
two holes and drill with appropriate size bit. For a
more secure fitting, the wall bracket can be anchored
using more than two holes.
Secure the bracket to the wall using:
IF CONCRETE OR BRICK - 8mm or 5/16 loxins or
dynabolts.
IF TIMBER - wood screw #20 or equivalent
(minimum 50mm long).
Attach the bracket to the support pipe assembly with
the 90mm long clevis pin (Fig. 15) and a snap pin.
Step 12 - Secure the Powerhead to the Ceiling
a.
b.
fig 15
Pipe adapter
14
GDO-7v2 SecuraLift® Owner Installation Instructions
Secure the perforated angle (not supplied) to the
ceiling above where powerhead’s mounting holes
will be. See (Fig.11) for a representative mounting.
Connect the powerhead to the ceiling mounted
perforated angle with M8x20mm screws and nuts.
Strips should not extend more than 18mm below
centre of powerhead mounting holes (Fig. 11).
WARNING: The opener must be securely
fastened to structural supports, otherwise opener
failure may ensue causing serious personal injury
and/or property damage.
Mounting Door Bracket & Arms
Step 13 - Mounting Door Bracket
The door bracket comes in two parts. The bottom plate
with two mounting holes is used on its own for one piece
doors. For sectional doors, the top plate is placed over
the bottom plate and is fixed with four (4) screws (Fig.
16).
a.
b.
fig 16
Mount the door bracket, or bracket assembly,
on the door’s centre line one-third down the top
panel (Fig. 16) using M6 or equivalent screws (not
supplied),
STEEL DOORS ONLY: Bracket can be welded in
place.
NOTE: If in doubt about the door’s strength,
reinforcement may be added to the door’s frame
where necessary. Door damage may occur if the
bracket is installed on a panel with insufficient
strength. The opener’s warranty does not cover
damage caused to the door and/or door panels.
fig 17
Step 14 - Attaching the Arms
FOR SECTIONAL AND ONE PIECE DOORS WITH
TRACK:
a. Assemble the bent and straight arms with bolts
and nuts supplied in the accessory pack (Fig. 17).
Always use both bent and straight arms.
b. Connect the assembled arm to the bracket and the
disengaged trolley with clevis and snap pins. The
angle “A” must be more less than 10° (Fig. 18).
WARNING: Connecting the bent arm other way
around may damage the door. The straight arm
should not protrude beyond heal of bent arm
A
0
FOR ONE PIECE DOORS WITHOUT TRACK
a. Assemble the bent and straight arms as shown
in (Fig. 19) with bolts and nuts supplied in the
accessory pack. Always use both the bent and
straight arms.
b. Connect the assembled arm to the bracket and the
disengaged trolley with clevis and snap pins.
c. If installing on a door with a bad wave action,
lengthening the arm will assist in reducing this
effect.
10
IMPORTANT NOTE: Adjust the length of the
cord so that its toggle is no more than 1.8m from
the ground.
fig 18
fig 19
Owner Installation Instructions GDO-7v2 SecuraLift®
15
Setting Limits
NOTE: If P.E. Beams are to be used they must be
installed before setting the travel limits.
Step 15.1 - Remove Controls Cover
Remove the controls cover to access the control panel
Replace it when setup is completed.
fig 20
Step 15.2 - Connect Power to the Powerhead
Plug the power cord into a mains point and switch power
on. The red CLOSE LIMIT LED will be flashing.
WARNING: The safety obstruction detection
system is inoperable while MINUS (-) and PLUS (+)
drive buttons are being used and travel limits are
not set.
Step 15.3 - Set the Datum Position
a.
fig 21
b.
Press and hold the MINUS (-) or PLUS (+) buttons to
move the door to the halfway position. Ensure that
the door, shuttle and chain index are engaged.
Using a small screwdriver, turn the DATUM ADJUST
screw until the STATUS LED comes on (Fig 20).
» If the STATUS LED is already illuminated when
the door is halfway up, turn the DATUM ADJUST
screw until the light goes off, then turn back one
notch to illuminate again.
Step 15.4 - Set the Limits Positions
a.
b.
c.
Press and hold the MINUS (-) button until the door
reaches the desired close limit position. Single
presses will the inch the door closed (Fig. 21).
Press the SET button to store the close position into
memory (Fig. 21).
Press and hold the PLUS (+) button until the door
reaches the desired open limit position. Single
presses will the inch the door open (Fig. 21).
IMPORTANT
WARNING: The door will
automatically close, open and close again once
Step 15.4(c) is performed. Ensure that no persons
or objects are in the door’s path.
d.
e.
Press the SET button to store the close position into
memory (Fig. 21).
The door will now automatically close and open to
calculate the safety obstruction settings. After this, the
opener can be operated with the OPERATE button.
Step 15.5 - Resetting the Door Limit Positions
Limit positions can be deleted by the following steps:
a. Press and hold the MINUS (-) button for six (6)
seconds until you hear three beeps and the CLOSE
LIMIT LED starts to flash (Fig. 21).
b. Release the CLOSE button.
c. Repeat Steps 15.1 to 15.4 to set new travel limit
positions..
16
GDO-7v2 SecuraLift® Owner Installation Instructions
Setting Limits: via Transmitter
The GDO-7v2 has the unique ability to set travel limits
using the transmitter, allowing the installer to move
around the garage and door to better assess the desired
close and open limit positions.
Step 16.1 - Power Up and Set the Datum
fig 22
Follow Steps 15.1 to 15.3 as outlined overleaf.
Observe all warnings!
a.
Step 16.2 - Code a Transmitter for Limit Setting
a.
b.
c.
Press and hold the DOOR CODE button (Fig. 22).
Press Button 1 on the transmitter for two seconds
(Fig. 23). Release and pause for two seconds.
Press the same button again on the transmitter
for two seconds.
Release the DOOR CODE button.
Button 1
(Inch Open)
Button 4
(Inch Close)
Step 16.3 - Setting Limits via Transmitter
a.
b.
c.
d.
e.
Press and hold Button 4 on the transmitter to close
the door. When the door is approx. 2cm from the
ground, press and hold Button 3 for two seconds
and release (Fig. 23).
Each press of Button 4 will allow you to “inch” the
door closed. Keep doing this until the door reaches
the desired close limit position.
If the door is closed too far, press Button 1
»
to “inch” the door towards open
When happy with the close limit position, press
Button 2 to store this in memory.
Press Button 1 to open the door. When approx.
2cm from the desired open position, press and hold
Button 3 for two seconds then release.
Each press of Button 1 will allow you to “inch” the
door open. Keep doing this until the door reaches
the desired open limit position.
If the door is opened too far, press Button
»
4 to “inch” the door towards closed
Button 2
(Set)
fig 23
Button 3 (
Switch between
fast and slow
inching)
IMPORTANT
WARNING: The door will
automatically close, open and close again once
Step 16.3(f) is performed. Ensure that no persons
or objects are in the door’s path.
f.
g.
When happy with the open limit position, press
Button 2 on the transmitter to store into memory.
The door will now automatically close and open to
calculate the safety obstruction settings. After this, the
opener can be operated with the OPERATE button.
Step 16.4 - Resetting the Door Limit Positions
Limit positions can be deleted by the following steps:
a. Follow Steps 15.5 (a) and (b), as outlined overleaf.
b. Repeat Steps 16.1 and 16.3 to set new travel limit
positions.
There is no need to re-code the transmitter
»
(Step 16.2) upon restting travel limits. The
transmitter will still be stored in memory.
Owner Installation Instructions GDO-7v2 SecuraLift®
17
Safety Obstruction Force Test
WARNING! Take care when testing or adjusting
the Safety Obstruction Force. Excessive force
may cause SERIOUS PERSONAL INJURY and/or
PROPERTY DAMAGE.
Step 17.1 - Testing Close Cycle
fig 24
a.
b.
c.
Press the OPERATE button to open the door (Fig. 24).
Place a piece of timber approximately 40mm high
on the floor directly under the door (Fig. 25).
Press the OPERATE button to close door. The door
should strike the object and start to re-open.
Step 17.2 - Testing Open Cycle
a.
b.
c.
fig 25
Press the OPERATE button to close the door (Fig. 24).
Press again to open the door. When the door reaches
the half open point, grab the bottom rail of the door
firmly and the door should stop.
If the door does not reverse readily when closing, or
stop when opening, the force may be excessive and
need adjusting, refer below.
DANGER! If the door fails these tests, put the
opener into manual mode, only operate the door
by hand and call for service.
Wood (40mm high)
18
GDO-7v2 SecuraLift® Owner Installation Instructions
Adjusting Safety Obstruction Forces
Adjusting Safety Obstruction Force
The Safety Obstruction Force is calculated automatically
during setup. Adjusting this is normally only necessitated
by environmental conditions such as windy or dusty areas,
and areas with extreme temperature changes.
WARNING: Doors that exert more than 400N
(40kgf) closing force must have a Photo Electric
Beam (P.E.Beam, Model: PE-2) fitted for safety.
a.
b.
c.
d.
Step 18.1 - To Increase Force Pressure
fig 26
Hold down FORCE MARGIN SET button (Fig. 26)
While holding the FORCE MARGIN SET button,
press the PLUS (+) button. Each press increases the
force margin.
The OPEN LIMIT LED will flash each time the PLUS
(+) button is pressed to indicate a force increase
If the OPEN LIMIT LED flashes continuously
•
when pressing the PLUS (+) button this
indicates that the maximum setting has
been reached.
Test the force again as per Steps 17.1 and 17.2
Step 18.2 - To Decrease Force Pressure
a.
b.
c.
a.
Hold down FORCE MARGIN SET button (Fig. 26)
While holding the FORCE MARGIN SET button,
press the MINUS (-) button. Each press decreases
the force margin.
The CLOSE LIMIT LED will flash each time the MINUS
(-) button is pressed to indicate a force increase
If the OPEN LIMIT LED flashes continuously
•
when pressing the PLUS (+) button this
indicates that the maximum setting has
been reached.
Test the force again as per Steps 17.1 and 17.2
Step 18.3 - To Recall Factory Set Force
a.
While holding down the FORCE MARGIN SET
button, press the SET button for two (2) seconds.
b.
Release both buttons. The default setting should
now be recalled.
Owner Installation Instructions GDO-7v2 SecuraLift®
19
Coding Transmitters
Step 19.1 - Code a Transmitter Button for
Door Operation
a.
b.
c.
d.
fig 27
Press and hold the DOOR CODE button (Fig. 27).
Press one of the four buttons on the transmitter for
two (2) seconds, pause for two (2) seconds, then
press the same button again for two (2) seconds.
Release the DOOR CODE BUTTON.
Press the transmitter button to test.
Step 19.2 - Coding a Transmitter Button to
the Courtesy Light
The transmitter can be programmed to operate the
courtesy light on the opener independently of the door
moving.
a. Press and hold LIGHT CODE button (Fig. 28).
b. Press one of the four buttons on the transmitter for
two (2) seconds, pause for two (2) seconds, then
press the same button again for two (2) seconds.
c. Release the LIGHT CODE button.
d. Press the transmitter button to test.
fig 28
Step 19.3 - Code a Transmitter Button for Pet
(Pedestrian) Mode
a.
b.
c.
d.
fig 29
Briefly press the DOOR CODE button three times,
then press it again and hold (will beep four times
on fourth press (Fig. 29)).
Press one of the four buttons on the transmitter for
two (2) seconds, pause for two (2) seconds, then
press the same button again for two (2) seconds.
Release the DOOR CODE button.
Press the transmitter button to test. To change the
default pet (pedestrian) door opening position,
refer Step 2.
Step 19.4 - Code a Transmitter Button to
Enable Vacation mode
The opener can be programmed into a “Vacation Mode”
where the opener will not respond to any transmitter
except one pre-programmed unit.
a. Briefly press the DOOR CODE button once, then
press it again and hold (will beep two times on
second press (Fig. 29)).
b. Press one of the four buttons on the transmitter for two (2) seconds, pause for two (2) seconds, then press the same
button again for two (2) seconds.
c. Release DOOR CODE button.
d. To test, press and hold the transmitter button for seven (7) seconds to set Vacation Mode.
e. To reset Vacation Mode press the same button for two seconds.
Step 19.5 - Code a Transmitter Button to Enable AUX OUTPUT
a.
b.
c.
d.
20
Briefly press the DOOR CODE button two times, then press it again and hold (will beep three times on third
press (Fig.29)).
Press one of the four buttons on the transmitter for two (2) seconds, pause for two seconds, then press the same
button again for two (2) second.
Release the DOOR CODE button.
Press the transmitter button to test.
GDO-7v2 SecuraLift® Owner Installation Instructions
Coding Transmitters
Step 20 - Remotely Coding Transmitters
Using this method transmitters can be coded without
access to the opener’s control panel as long as a precoded transmitter is available.
Coding hole
IMPORTANT NOTE: The door or courtesy light
must activate when the steps below are performed.
This indicates that the pre-coded transmitter is in
range of the opener, and the correct button has
been pressed.
a.
b.
c.
d.
e.
Take any pre-coded transmitter. Press the button
for the function to be duplicated and release.
Using a small needle, press and hold firmly for
two seconds through the Coding Hole (Fig. 30).
WITHIN 10 SECONDS take the additional
transmitter you wish to code. Decide which
button that you want to activate the function to
be duplicated (e.g. activate the door, or turn on
the courtesy light)
Hold the new transmitter’s button for two
seconds, pause for two seconds, hold again for
two seconds and then release.
Wait for 10 seconds and then press the new
transmitter’s button to test.
fig 30
Small needle
fig 31
Step 21. Deleting Programmed Codes
Step 21.1 - Deleting a Stored Transmitter
Code
a.
b.
c.
d.
Select the transmitter you want to delete.
Press and hold the DOOR CODE BUTTON (Fig.
31).
Press the transmitter button you would like to
delete for two seconds, pause for two seconds,
press again for two seconds and then release.
Release the DOOR CODE BUTTON. The code
should now be deleted. Confirm this by pressing
the transmitter button - the function (e.g. door
opening) should not respond.
Step 21.2 - Deleting All Transmitter Codes
a.
b.
c.
d.
1. Turn off power to the opener.
While switched off, press and hold the DOOR
CODE BUTTON (Fig. 31). Turn on power to the
opener while holding this button.
The OPEN LIMIT, CLOSE LIMIT and DOOR
STATUS LEDs will illuminate for about five
seconds. These LED’s will turn off and the
CODING LED will illuminate.
Release the DOOR CODE BUTTON. All stored
codes will now be deleted. Confirm this pressing
buttons on any previously coded transmitters the opener should not respond.
Owner Installation Instructions GDO-7v2 SecuraLift®
21
P.E. Beams & Auto-close
RECEIVER
12V
Affix the P.E. Beams (PE-2) in a strategic location
within the doorway. We recommend 150mm above
the floor level and as close as possible to the door
opening, inside the garage.
b. Connect the PE-2 (Order Code 90214) and the
P.E.Beam Interface Kit V2 (Order Code 01901) to
the Opener in accordance with (Fig.32).
NOTE: Resistor R1 shall be 2.2kOhm, 1/4W.
Make sure to align the beams correctly. Follow the
manual supplied with the P.E. Beams.
a.
12V
24V
24V
1 2 3 4 5
fig
Step 22 - Fitting the P.E. Beams (optional)
TRANSMITTER
1 2 3 4 5
32
R
B
Y
R1
R
B
R
WARNING: The P.E.Beams will be active only after
the Opener has moved the door through a
completed open or close cycle.
J6
CABLE 2
R
CABLE 1
Y
B
PWR
IR
IR(0V)
WIRE COLOUR: B-Black; R-Red; Y-Yellow.
Resistor R1 shall be 2.2kOhm, 1/4W.
WARNING: When using Auto Close Mode and P.E.
beams, the doorway must be clear of all obstructions
and persons at all times. The location of the beams
and manner in which it is installed might not give
safety protection at all times. Check to make sure
that the height of the beam and type used give
maximum protection possible.
Model: PE-2 with harness
Step 23 - Setting Up Auto-close Mode
IMPORTANT NOTICE: It is compulsory to have P.E.
Beams installed when using Auto-close mode.
Auto-close mode is a function that automatically closes
the door a pre-set time after the P.E. Beams recognise
that a vehicle has left the garage.
The Auto-close timer only starts after the P.E. Beam's
path is broken the Auto-close timer has been set. If
the P.E. path is not broken the door will remain open
until the path is broken.If the opener incurs a physical
obstruction (i.e. not from the P.E.Beams) while closing
the door will re-open and not Auto-close until the P.E.
Beam's path is broken again.
Step 22.1 - Setting Auto-close Time
a.
b.
c.
fig 33
d.
e.
22
GDO-7v2 SecuraLift® Owner Installation Instructions
Hold down the AUTO CLOSE TIME button (Fig.33).
While holding in the AUTO CLOSE TIME button,
press the PLUS (+) button - each press will add
one second to the Auto-close delay.
To decrease the delay time follow Step 22.1(a)
and press the MINUS (-) button - each press will
deduct one second from the Auto-close delay.
Press the OPERATE button or transmitter to open
the door. When the door is fully opened the
OPEN LIMIT LED will flash to indicate that Autoclose mode is operational.
Break the P.E. Beam's path momentarily to
initialise Auto-close. When the door reaches the
fully opened position, the door will pause for the
set Auto-close time and then close.
Final Set Up
Step 24 - Setting of Courtesy Light Time
The courtesy light time can only be adjusted with the
Universal Programmer (PG-3).
Step 25 - Setting the Pet Mode position
fig 34
The default Pet Mode height can be changed as follows:
a. Make sure the door is closed, then press and hold
the PLUS (+) button for six (6) seconds (Fig.34)
until you hear three beeps and the OPEN and
CLOSE LEDs flash rapidly.
b. Press the PLUS (+) or MINUS (-) button to move
the door to the desired pet mode open position.
c. Press the SET button to record the new position.
When activated, Pet Mode drives the door to the preset
position from either above or below. Pet Mode’s active
status is indicated by both the OPEN and CLOSE LIMIT
LEDs being illuminated. If a Pet Mode button is pressed
while the door is moving the door will stop. If a Pet
Mode button is pressed when the door is in the Pet
position, then the door will close.
fig 35
Step 26 - Installing the Wall Mounted
Transmitter (Optional)
a.
b.
c.
d.
Remove the faceplate from the transmitter.
Affix the baseplate in a convenient wall location
that is out of reach of children and convenient
to the customer (Fig.35). Make sure the door is
visible from this location.
Replace the faceplate.
To code the transmitter, see Step 19 on page
20.
Step 27 - Re-initialising the Opener
a.
b.
c.
Press and hold the SET Button for two (2) seconds,
the beeper will sound once (Fig.36).
The door will start to move and re-calculate force
margins. The door can move between the open and
close limit positions up to four (4) times (depending
on the position of the door and the power up
condition).
A single beep will be heard once the initialisation is
complete. The door is now ready for use.
fig 36
Owner Installation Instructions GDO-7v2 SecuraLift®
23
Parameters
Door Status Indicators
Door Opener State
OPEN LED (Green)
Open
On
Close
Opening
Beeper
On
Flashing
Closing
Flashing
Door travel stopped
Flashing
Door obstructed when opening
Flashing
Door obstructed when closing
24
CLOSE LED (Red)
Flashing
Flashing
Opener overloaded
Alternating flashes
Door in open position with AutoClose mode selected
One second flashes
Mains power interrupted
Rapid flashes
GDO-7v2 SecuraLift® Owner Installation Instructions
Alternating flashes
Beeps as door moves
Parameters
Button Functions
Buttons
Function
OPERATE
Opens/Stops/Closes the door
DOOR CODE
Codes a transmitter button for operate function,
Pet, Vacation Modes and AUX functions
LIGHT CODE
Codes a transmitter button for light function
FORCE MARGIN SET & OPEN
Increases the obstruction force margin setting
FORCE MARGIN SET & CLOSE
Decreases the obstruction force margin setting
FORCE MARGIN SET (then) SET
Resets the factory default force margin settings
AUTO CLOSE TIME (then) OPEN
Increases the auto close delay time
AUTO CLOSE TIME (then) CLOSE
Decreases the auto close delay time
AUTO CLOSE TIME (then) SET
Resets the factory default auto close delay time
FORCE MARGIN SET & AUTO CLOSE TIME (then) SET
Reloads the factory default light time
CLOSE (for 6 secs.)
Clears the door limits set positions. Limits then
need to be reset
SET & CLOSE (for 2 secs.)
Enters pet (pedestrian) position mode
SET (then power on) & hold until all LEDs are off
Deletes control parameters excluding transmitter
storage memory
DOOR CODE (then power on) & hold until all LEDs
are off
Deletes all transmitter storage memory
SET & DOOR CODE (the power on) and hold until all
LEDs are off
Deletes all control parameters and transmitter
storage memory.
SET
Re-initialises the Opener to re-calculate force
margin
Owner Installation Instructions GDO-7v2 SecuraLift ®
25
Default Settings & Specifications
Factory Default Settings
Default
Step
Maximum
Courtesy light time
4 min
-
-
Obstruction force margin
2
1
26
Auto-close time
0 sec
1
4 min
Technical Specifications
Mains
230-240V AC, 50Hz
Standby power
2.2 Watts
Rated input power
550 Watts
Motor rating
250 Watts (1/3 HP)
Motor type
Alternating Current
Shuttle travel distance
* 2.7m approx. (Standard)
Maximum shuttle travel distance in the C-Rail
* 3.750m (with extension)
Maximum door size
16.5m2 (5500mm (Width) x 3000mm (Height))
Maximum door weight
225kg
Short-term peak force
700N (70kg)
Rated lift force
500N (50kg)
Recommended force for manual operation
(excessive force)
No greater than 150N (15kg)
Rated operating time
2 min in 30 min
Receiver code storage capacity
14 x 4 button Transmitter Codes
Transmitter/Receiver type
UHF Multi-frequency FM
Coding type
Multi-frequency Code Hopping
Number of code combinations
Over 4.29 Billion random codes
Code generation
Non-linear encryption algorithm
Transmitter battery
CR2032 (3V)
Courtesy light
Edison (screw mount) 240V 60W rough service (or
construction type)
Controller fuse
5A slow blow
NOTE:
1. The door must be well balanced. A person should be able to lift the door up manually with very little effort in
case of an emergency.
2. Intermittent operations may occur in areas which experience very strong winds. Strong wind puts extra pressure
on the door and tracks which may in turn trigger the safety obstruction detection system intermittently.
26
GDO-7v2 SecuraLift® Owner Installation Instructions
Troubleshooting
Symptom
Door will not operate
Possible cause
Remedy
Mains power not switched on.
Switch on mains power.
Door is obstructed.
Remove obstruction.
Door is locked or motor jammed.
Unlock door or remove jam.
Door tracks/hardware damaged.
Door requires service/repair by
qualified technician.
The opener is in “vacation mode”
Turn off “vacation mode”.
Adverse weather conditions (wind
or cold) causing door to stiffen and
become tight in the tracks.
Increase force margin setting
See page 19 or re-calculate force
margin.
Possible obstruction in the
doorway.
Remove obstruction.
Door operates from drive unit
(OPERATE) button but not from
transmitter*
Transmitter code not stored in
memory.
Code transmitter in to openers
memory. Refer step 19.1 on page
20
See note
Flat battery.
Replace battery
Broken battery lead inside
transmitter
Send transmitter to installer or
Automatic Technology for repair
Door will not close fully.
Door limits positions need to be
reset.
Reset limits positions. Step 16.4,
page 17.
Door will not open fully.
Door limits positions need to be
reset.
Reset limits positions. Step 16.4,
page 17.
Courtesy light not working
Globe down
Replace globe - Edison type 240V
60W
Globe keeps blowing
Incorrect globe voltage - must be
240V AC
Replace globe - Edison type 240V
60W
Door starts to close but
automatically reverses to open
position
Auto close not working
PE Beam or wiring faulty.
Repair PE Beam or replace wiring.
PE Beam not aligned correctly.
Re-align optics.
PE Beam is obstructed.
Remove obstruction from path of
PE.
Door obstructed when closing.
Remove obstruction.
Auto close time not set.
See Step 23 on page 22.
Auto close mode not set
See Step 23 on page 22.
PLEASE NOTE:
Some areas may be prone to excessive radio interference brought on by devices such as cordless telephones,
wireless stereo headphones and baby monitors. It is possible that these devices could cause a degree of
interference such as to greatly reduce the range of the transmitter. In such an instance please contact your
Automatic Technology dealer for an alternative frequency replacement kit. As this is not a warrantable situation
but an environmental issue charges may apply for the change-over.
Owner Installation Instructions GDO-7v2 SecuraLift®
27
Maintenance
Maintenance
Yearly
The SERVICE LED will indicate the requirement for
a service and/or adjustment. To reset the SERVICE
LED when the door is serviced, reprogram the
Door Travel Limits and the Door Travel Force – on
completion of this programming the SERVICE LED
will go out.
Automatic Technology suggests you contact your installer
to perform an annual door service.
Whilst your opener does not require any periodic
maintenance, the door that it is fitted to does. Your
garage door is a large, heavy, moving object and
should be tested regularly to ensure it is in good
condition. A poorly maintained door could cause fatal
or serious injuries or serious damage to property.
To ensure a long and trouble free life for your opener
the following is recommended:
CAUTION: Frequently examine door, particularly
cables, springs and mountings for signs of wear,
damage or imbalance. Do not use if repair or
adjustment is needed since a fault in the installation or
an incorrectly balanced door may cause injury. (AS3350)
Adjustments should only be carried out by experienced
persons, as this function can
be dangerous if not performed under strict safety
procedures.
WARNING! Failure to maintain your garage
door may void the warranty on your garage door
opener.
Monthly
•
•
Disengage the opener and manually operate
the door: The door must be smooth to operate
by hand. An operating force on the bottom rail
should not exceed 150N (15kg) force.
Each month check that the opener reverses
when the door contacts a 50mm high object
placed on the floor (AS3350). Refer to Testing
the Safety System (Step 16).
Warranty Expired Indicator
When the opener reaches the number of cycles covered
by warranty the courtesy light will flash 10 times after each
operation to indicate that the warranty has expired. This
flashing will continue for twenty (20) operations unless
the user acknowledges the warranty expiry indicator and
stops the light from flashing. To stop the courtesy light
flashing press the LIMIT SET button while the light is
flashing after an operation.
NOTE: If the door does not operate smoothly, call
your installer.
Service Record
Record any maintenance in the following table to assist in any warranty service.
Date
28
Service by
Signature
GDO-7v2 SecuraLift® Owner Installation Instructions
Invoice No.
Amount
Spare Parts
ITEM
60
61
62
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
DESCRIPTION
BASE AV2 SUB ASSY
GEARBOX BASE ASSY
RUBBER STOP BRACKET
CAPACITOR 15uF
TAPTITE SCREW “P” M4x8
TAPTITE SCREW “S” M4x10
TERMINAL BLOCK 2 WAY
CAP POLYFILM 0.1uF/275VAC X2
PAN HD SCREW M3x14
LAMP HOLDER LS-204-1
GLOBE 240V 60W
DRIVE SHAFT 12.7-156
THRUST WASHER NTA-815
WAVE SPRING WASHER
E-CIRCLIP N1540 0050
HELICAL GEAR 34209
GEARBOX LID ASSY
AC MOTOR 250W FM-62409B
HEX SPACER M5 8A/Fx10
RUBBER STOP 20x10
SEL-LOCK PIN SPRING ACP M4x20
BALL BEARING R8ZZ
WORM 2520x50-2S
CHOPPER CLIP
CHOPPER WHEEL
RATCHET TIMING ASSY
SENSOR ASSY SV1
TAPTITE SCREW “P” M3x8
COVER SP AV2
SPROCKET 8T SPL
CHAIN SPREADER SV1
FLANGE TAPTITE SCREW “S” M4x10
BOARD SHIELD ABC05
CONTROL BOARD ACB05
BOARD HOUSING S-AY AV2
CONTROLS LID
LIGHT DIFFUSER
TUBE 338605
TUBE INSERT 2970
INDEX TUBE 338605
CHAIN 1/2’x1/8’ (499 LINKS)
CLEVIS PIN DIA 8
SNAP PIN SSP 8 ZNU 31080
CHAIN INDEX CX ASSY
SHUTTLE ASSY
CHAIN JOINT LINK
HEX SARRATION FLANGE NUT M8
PIPE ADAPTER ASSY
WHEEL AXLE
CHAIN IDLE WHEEL
PIPE ADAPTER
SNAP PIN SSP-12
WALL BRACKET
PIN
DOOR BRACKET LOCATOR
DOOR BRACKET
STRAIGHT ARM
BENT ARM
HEX HEAD SCREW M8x25
POWER CORD ASSY
CORD GRIP GROMMET SB5P-2
HARNESS AV2
Owner Installation Instructions GDO-7v2 SecuraLift®
ORDER
CODE
02153
71666
02644
14402
10581
10504
05421
07575
10361
05761
14210
04543
14300
12380
10799
04941
71668
14411
11192
02640
02590
03916
72212
04960
04951
01737
01689
10560
01595
72210
72435
10497
14052
00822
01587
05108
13902
13801
13830
13811
03000
02550
10720
01452
00272
02950
10148
00297
13845
02962
13727
10730
02521
05790
02515
02511
02800
02950
10110
05666
05606
14142
29
Warranty and Exclusion of Liability
1. This warranty is an addition to any non-excludable conditions or warranties that are implied into this contract
by relevant statute, including the Trade Practices Act 1974 (Cwth).
2. Subject to all of the matters set out below, Automatic Technology Australia Pty Ltd (“ATA”) warrants:
(a) overhead door opener drive units for twenty four (24) months or 5000 cycles, whichever occurs first; and
(b) all components and accessories for twelve (12) months, from the date of purchase (specified in the sales
docket receipt) as free of any defects in material and workmanship.
3. This warranty applies only where the purchaser:
(a) immediately notifies ATA or the retailer of the alleged defect;
(b) returns the product to the retailer; and
(c) presents the relevant sales docket and this warranty document to the retailer to confirm the date
of purchase.
4. Except for this warranty, ATA gives no warranties of any kind whatsoever (whether express or implied), in
relation to the product, and all warranties of whatsoever kind relating to the product are, to the extent
permissible by statute, hereby excluded.
5. To the extent permissible by statute, ATA disclaims any liability of whatsoever nature in respect of any claim or
demand for loss or damage which arises out of:
(a) accidental damage to or normal wear and tear to the product or to the product’s components;
(b) any cost relating to damage resulting from wear and tear;
(c) blown fuses, loss or damage caused by electrical surges, power surges or power spikes;
(d) loss or damage due to theft, fire, flood, rain, water, lightning, storms or any other acts of God;
(e) maximum continuous operating time exceeding one (1) minute in ten (10);
(f) maximum operating force exceeding *20kg (200N) when moving the door manually to the open or closed
position;
(g) door surface area and/or weight exceeding 16.5m2 and 100kg respectively;
(h) door not in safe and correct working order and condition;
(i) evidence of unauthorised repairs;
(j) any cost relating to damage caused by misuse, negligence or failure to maintain the equipment in a
proper working order as per clauses (d) through (h);
(k) installation, adjustment or use which is not in accordance with the instructions set out in installation
instruction manual
(l) attempted or complete modification or repairs to the product carried out by a person who is not
authorised or has not been trained by ATA to carry out such modification or repairs;
(m) faulty or unsuitable wiring of structure to which the product is fixed or connected;
(n) radio (including citizen band transmission) or any electrical interference;
(o) damage caused by insects;
(p) loss or damage to any property whatsoever or any loss or expense whatsoever resulting or arising there
from or any consequential loss;
(q) any cost or expense arising due to manufacturer recall of any product;
(r) any cost or expense due to negligence of the approved service provider;
(s) installation of a residential garage door opener in a commercial or industrial situation or a non-single
residential dwelling.
6. ATA’s liability under this warranty is limited, at ATA’s absolute option, to replacing or repairing the product
which ATA, in its unfettered opinion, considers to be defective either in material and/or workmanship or to
credit the dealer with the price at which the product was purchased by the dealer.
7. This warranty does not extend to cover labour for installation.
8. This warranty is limited to Return-to-Base (RTB) repair and does not cover labour for on-site attendance.
9. This warranty is void if the Product is not returned to the manufacturer in original or suitably secure packaging.
10. This warranty is only applicable for repairs to the product carried out within Australia.
11. This warranty does not cover consumable items including globes, batteries and fuses.
12. This warranty is not transferable.
13. Where the Product is retailed by any person other than ATA, except for the warranty set out above, such
person has no authority from ATA to give any warranty or guarantee on ATA’s behalf in addition to the
warranty set out above.
NOTES:
1. One (1) cycle = one (1) open and one (1) close action of the door or gate.
2. This warranty is to be read in conjunction with the owner’s copy of the installation instruction manual.
3 *The door should be balanced in such a way that the user manually is able to open or close the door without using
force not greater than 150N (15kg ) although a greater force may be required for the start of the movement.
30
GDO-7v2 SecuraLift® Owner Installation Instructions
Owner Installation Instructions GDO-7v2 SecuraLift®
31
© January 2008 Automatic Technology (Australia) Pty Ltd. All rights reserved. TrioCode™ and SecuraLift® are trademarks
of Automatic Technology (Australia) Pty Ltd. No part of this document may be reproduced without prior permission. In an
ongoing commitment to product quality we reserve the right to change specification without notice. E&OE.
Automatic Technololgy (Australia) Pty Ltd
ABN 11 007 125 368
6-8 Fiveways Boulevard
Keysborough, Victoria, 3173, Australia
P 1300 133 944
+61 2 9722 5666 (International Enquiries Only)
E sales@ata-aust.com.au
www.ata-aust.com.au
GARAGE DOOR OPENERS | GATE OPENERS | REMOTE CONTROL ACCESS SOLUTIONS
Download PDF