WSB-9452 User's Manual
WSB-9452 PICMG 1.0 CPU Card
IEI Technology Corp.
MODEL:
WSB-9452
Full-Size PICMG 1.0 CPU Card with Intel® Core™2 Duo/Solo,
VGA/DVI, Dual PCIe GbE, SATA 3Gb/s and Audio
User Manual
Page I
Rev. 2.01 – 12 October, 2010
WSB-9452 PICMG 1.0 CPU Card
Revision
Date
Version
Changes
2010-10-12
2.01
Minor changes
2008-10-28
2.00
Changed northbridge chipset from Intel® 945GM to Intel® 945GME
Added JAUTO1 and JLAN_PWR1 jumpers information
2007-09-04
1.01
Changed the Maximum memory in Table 1-1 from 2GB to 4GB
Added Disclosure of Hazardous Materials Appendix (Appendix F)
Added Packing List Chapter (Chapter 3)
2006-12-18
Page II
1.0
Initial release
WSB-9452 PICMG 1.0 CPU Card
Manual Conventions
WARNING!
Warnings appear where overlooked details may cause damage to the equipment or result
in personal injury. Warnings should be taken seriously. Warnings are easy to recognize.
The word “warning” is written as “WARNING,” both capitalized and bold and is followed by
text. The text is the warning message. A warning message is shown below:
WARNING:
This is an example of a warning message. Failure to adhere to warning
messages may result in permanent damage to the WSB-9452 or
personal injury to the user. Please take warning messages seriously.
CAUTION!
Cautionary messages should also be heeded to help reduce the chance of losing data or
damaging the WSB-9452. Cautions are easy to recognize. The word “caution” is written as
“CAUTION,” both capitalized and bold and is followed. The italicized text is the cautionary
message. A caution message is shown below:
Page III
WSB-9452 PICMG 1.0 CPU Card
CAUTION:
This is an example of a caution message. Failure to adhere to cautions
messages may result in permanent damage to the WSB-9452. Please
take caution messages seriously.
NOTE:
These messages inform the reader of essential but non-critical information. These
messages should be read carefully as any directions or instructions contained therein can
help avoid making mistakes. Notes are easy to recognize. The word “note” is written as
“NOTE,” both capitalized and bold and is followed by text. The text is the cautionary
message. A note message is shown below:
NOTE:
This is an example of a note message. Notes should always be read.
Notes contain critical information about the WSB-9452. Please take
note messages seriously.
Page IV
WSB-9452 PICMG 1.0 CPU Card
Copyright
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page V
WSB-9452 PICMG 1.0 CPU Card
Table of Contents
1
INTRODUCTION..................................................................................................... 1
1.1 WSB-9452 CPU CARD OVERVIEW ............................................................................ 2
1.1.1 WSB-9452 Model Variations .............................................................................. 2
1.1.2 WSB-9452 CPU Card Applications ................................................................... 2
1.1.3 WSB-9452 CPU Card Benefits........................................................................... 2
1.1.4 WSB-9452 CPU Card Features ......................................................................... 3
1.2 WSB-9452 CPU CARD OVERVIEW ............................................................................ 4
1.2.1 WSB-9452 CPU Card Connectors ..................................................................... 5
1.2.2 Technical Specifications..................................................................................... 6
2
DETAILED SPECIFICATIONS ............................................................................. 9
2.1 COMPATIBLE IEI BACKPLANES................................................................................. 10
2.2 CPU SUPPORT .......................................................................................................... 10
2.2.1 Intel® Core™2 Duo.......................................................................................... 10
2.2.2 Intel® Core™ Duo.............................................................................................11
®
2.2.3 Intel Core™ Solo ............................................................................................11
2.2.4 Intel® Celeron® M ............................................................................................ 12
2.3 ON-BOARD CHIPSETS ............................................................................................... 12
2.3.1 Northbridge and Southbridge Chipsets ........................................................... 12
2.3.2 Intel® 945GME Northbridge Chipset............................................................... 12
2.3.3 Intel ICH7-M Southbridge Chipset.................................................................. 13
2.4 GRAPHICS SUPPORT.................................................................................................. 14
2.4.1 Intel® GMA 950................................................................................................ 14
2.4.2 Analog VGA ..................................................................................................... 15
2.4.3 Digital LVDS.................................................................................................... 15
2.4.4 Digital Visual Interface (DVI).......................................................................... 15
2.5 DATA FLOW .............................................................................................................. 16
2.6 MEMORY SUPPORT ................................................................................................... 17
2.7 PCI BUS INTERFACE SUPPORT .................................................................................. 17
2.8 GBE ETHERNET CONNECTION .................................................................................. 18
2.9 DRIVE INTERFACES .................................................................................................. 18
Page VI
WSB-9452 PICMG 1.0 CPU Card
2.9.1 SATA Drives ..................................................................................................... 19
2.9.2 IDE HDD Interfaces ........................................................................................ 19
2.9.3 Floppy Disk Drive (FDD)................................................................................ 19
2.10 SATA II AND RAID FUNCTIONALITY (SATA3 AND SATA4 ONLY)......................... 20
2.11 SERIAL PORTS......................................................................................................... 20
2.12 REAL TIME CLOCK ................................................................................................. 20
2.13 SYSTEM MONITORING ............................................................................................ 21
2.14 INFRARED DATA ASSOCIATION (IRDA) INTERFACE ................................................ 21
2.15 USB INTERFACES ................................................................................................... 21
2.16 BIOS...................................................................................................................... 21
2.17 OPERATING TEMPERATURE AND TEMPERATURE CONTROL ..................................... 22
2.18 OPTIONAL AUDIO INTERFACE ................................................................................. 22
2.19 POWER CONSUMPTION ........................................................................................... 22
2.20 PACKAGED CONTENTS AND OPTIONAL ACCESSORY ITEMS ..................................... 23
2.20.1 Package Contents........................................................................................... 23
2.20.2 Special Items .................................................................................................. 23
2.20.3 Optional Accessory Items............................................................................... 24
3
UNPACKING .......................................................................................................... 25
3.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 26
3.2 UNPACKING .............................................................................................................. 26
3.2.1 Unpacking Precautions.................................................................................... 26
3.3 UNPACKING CHECKLIST ........................................................................................... 27
3.3.1 Package Contents............................................................................................. 27
3.4 OPTIONAL ITEMS ...................................................................................................... 29
4
CONNECTORS AND JUMPERS ......................................................................... 30
4.1 PERIPHERAL INTERFACE CONNECTORS..................................................................... 31
4.1.1 WSB-9452 CPU card Layout ........................................................................... 31
4.1.2 Peripheral Interface Connectors ..................................................................... 32
4.1.3 External Peripheral Interface Connectors....................................................... 33
4.1.4 On-board Jumpers ........................................................................................... 34
4.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 34
4.2.1 ATX-12V Power Source Connector.................................................................. 34
4.2.2 Audio Module Connector ................................................................................. 36
Page VII
WSB-9452 PICMG 1.0 CPU Card
4.2.3 Backplane to Mainboard Power Connector .................................................... 37
4.2.4 Battery Connector............................................................................................ 39
4.2.5 CPU Fan Connector ........................................................................................ 40
4.2.6 Digital Input/Output (DIO) Connector............................................................ 42
4.2.7 DVI (Digital Visual Interface) Connector........................................................ 43
4.2.8 FDD Connector ............................................................................................... 45
4.2.9 Front Panel Connector .................................................................................... 47
4.2.10 IDE Connectors ............................................................................................. 49
4.2.11 Inverter Connector ......................................................................................... 50
4.2.12 IrDA Interface Connector .............................................................................. 52
4.2.13 Keyboard Connector ...................................................................................... 53
4.2.14 LVDS Connector ............................................................................................ 55
4.2.15 Parallel Port Connector ................................................................................ 56
4.2.16 PCI Express Mini Card Connector ................................................................ 58
4.2.17 RS-232 Serial Port Connectors...................................................................... 61
4.2.18 SATA Drive Connectors ................................................................................. 63
4.2.19 Trusted Platform Module Connector ............................................................. 65
4.2.20 TV Out Connector .......................................................................................... 67
4.2.21 USB Connectors............................................................................................. 69
4.3 EXTERNAL PERIPHERAL INTERFACECONNECTORS ................................................... 70
4.3.1 LAN Connectors............................................................................................... 71
4.3.2 Mini-DIN 6 PS/2 Connector .......................................................................... 72
4.3.3 USB Connector ................................................................................................ 73
4.3.4 VGA connector ................................................................................................. 74
5
INSTALLATION AND CONFIGURATION ....................................................... 76
5.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 77
5.2 INSTALLATION CONSIDERATIONS .............................................................................. 77
5.2.1 Installation Notices .......................................................................................... 77
5.3 UNPACKING .............................................................................................................. 78
5.3.1 Unpacking Precautions.................................................................................... 78
5.3.2 Checklist........................................................................................................... 79
5.4 WSB-9452 CPU CARD INSTALLATION..................................................................... 80
5.4.1 Socket 478 CPU Installation............................................................................ 81
5.4.2 Cooling Kit (CF-479B-RS ) Installation .......................................................... 83
Page VIII
WSB-9452 PICMG 1.0 CPU Card
5.4.3 DIMM Module Installation .............................................................................. 86
5.4.3.1 Purchasing the Memory Module............................................................... 86
5.4.3.2 DIMM Module Installation....................................................................... 87
5.4.4 Peripheral Device Connection......................................................................... 89
5.4.4.1 IDE Disk Drive Connectors (IDE1, IDE2) ............................................... 90
5.4.4.2 Floppy Drive Connector (FDD1).............................................................. 92
5.4.5 SATA Drive Connection ................................................................................... 92
5.4.6 Installing the RS-232 Cable ............................................................................. 94
5.4.7 USB 2.0 Cable Connection .............................................................................. 95
5.5 ON-BOARD JUMPERS ................................................................................................ 97
5.5.1 AT Power Select Jumper Settings..................................................................... 97
5.5.2 Clear CMOS Jumper........................................................................................ 98
5.5.3 LVDS LCD Voltage Selection......................................................................... 100
5.5.4 LAN Power Selection ..................................................................................... 102
5.6 CHASSIS INSTALLATION .......................................................................................... 104
5.7 REAR PANEL CONNECTORS .................................................................................... 104
5.7.1 Keyboard and Mouse Connection.................................................................. 104
5.7.2 VGA Port Installation .................................................................................... 104
5.7.3 Ethernet Connection ...................................................................................... 104
5.7.4 USB Connection............................................................................................. 104
6
AMI BIOS SETUP................................................................................................ 105
6.1 INTRODUCTION....................................................................................................... 106
6.1.1 Starting Setup................................................................................................. 106
6.1.2 Using Setup .................................................................................................... 106
6.1.3 Getting Help................................................................................................... 107
6.1.4 Unable to Reboot after Configuration Changes ............................................ 107
6.1.5 BIOS Menu Bar.............................................................................................. 107
6.2 MAIN...................................................................................................................... 108
6.3 ADVANCED ............................................................................................................. 109
6.3.1 CPU Configuration......................................................................................... 111
6.3.2 IDE Configuration ..........................................................................................112
6.3.2.1 IDE Master, IDE Slave ............................................................................115
6.3.3 Floppy Configuration......................................................................................119
6.3.4 Super IO Configuration ................................................................................. 120
Page IX
WSB-9452 PICMG 1.0 CPU Card
6.3.5 Hardware Health Configuration.................................................................... 124
6.3.6 ACPI Configuration ....................................................................................... 127
6.3.6.1 General ACPI Configuration................................................................... 128
6.3.7 APM Configuration........................................................................................ 130
6.3.8 MPS Configuration ........................................................................................ 133
6.3.9 Remote Access Configuration ........................................................................ 134
6.3.10 Trusted Computing ....................................................................................... 139
6.3.11 USB Configuration ....................................................................................... 140
6.4 PCI/PNP................................................................................................................. 143
6.5 BOOT...................................................................................................................... 151
6.5.1 Boot Settings Configuration........................................................................... 151
6.5.2 Boot Device Priority ...................................................................................... 155
6.5.3 Hard Disk Drives ........................................................................................... 156
6.5.4 Removable Drives .......................................................................................... 157
6.6 SECURITY ............................................................................................................... 159
6.7 CHIPSET ................................................................................................................. 161
6.7.1 Northbridge Configuration ............................................................................ 162
6.7.1.1 Video Function Configuration ................................................................ 165
6.7.2 Southbridge Configuration ............................................................................ 170
6.8 EXIT ....................................................................................................................... 173
7
SOFTWARE DRIVERS ....................................................................................... 175
7.1 AVAILABLE SOFTWARE DRIVERS ............................................................................ 176
7.2 CHIPSET DRIVER INSTALLATION ............................................................................. 176
7.3 VGA DRIVER ......................................................................................................... 181
7.4 BROADCOM LAN DRIVER (FOR GBE LAN) INSTALLATION ................................... 186
7.5 REALTEK HD AUDIO DRIVER (ALC883) INSTALLATION ........................................ 192
7.5.1 BIOS Setup ..................................................................................................... 192
7.5.2 Driver Installation ......................................................................................... 192
7.6 REALTEK AC`97 AUDIO DRIVER (ALC665) INSTALLATION ................................... 197
7.6.1 BIOS Setup ..................................................................................................... 197
7.6.2 Driver Installation ......................................................................................... 197
A
BIOS CONFIGURATION OPTIONS ................................................................ 205
A.1 BIOS CONFIGURATION OPTIONS ........................................................................... 206
Page X
WSB-9452 PICMG 1.0 CPU Card
B
WATCHDOG TIMER .......................................................................................... 210
C
EXTERNAL AC’97 AUDIO CODEC ................................................................. 213
C.1 INTRODUCTION ...................................................................................................... 214
C.2 PHYSICAL CONNECTION ........................................................................................ 216
C.3 DRIVER INSTALLATION .......................................................................................... 216
C.4 SOUND EFFECT CONFIGURATION ........................................................................... 218
C.5 SOUND EFFECT ...................................................................................................... 219
C.6 ENVIRONMENT SIMULATION .................................................................................. 219
C.7 KARAOKE MODE ................................................................................................... 221
C.8 EQUALIZER SELECTION ......................................................................................... 222
C.9 SPEAKER CONFIGURATION..................................................................................... 223
C.10 SPEAKER TEST ..................................................................................................... 224
C.11 S/PDIF-IN & S/PDIF-OUT .................................................................................. 225
C.12 CONNECTOR SENSING .......................................................................................... 226
C.13 HRTF DEMO ....................................................................................................... 229
C.14 MICROPHONE EFFECT .......................................................................................... 229
C.15 GENERAL ............................................................................................................. 230
D
JMICRON RAID SETUP .................................................................................... 231
D.1 INTRODUCTION ...................................................................................................... 232
D.1.1 RAID Support................................................................................................ 232
D.1.2 What is RAID................................................................................................. 232
D.2 RAID SETUP ......................................................................................................... 233
D.2.1 Introduction................................................................................................... 233
D.2.2 Install SATA Drives ....................................................................................... 233
D.2.3 Configure the SATA Controller in BIOS........................................................ 233
D.2.4 Configure the RAID BIOS ............................................................................. 234
D.2.4.1 Create a RAID volume........................................................................... 235
D.2.4.2 Delete a RAID volume........................................................................... 239
D.2.4.3 Revert an HDD to Non-RAID ............................................................... 241
D.2.4.4 Solve Mirror Conflict............................................................................. 243
D.2.4.5 Rebuild Mirror Drive ............................................................................. 244
D.2.4.6 Save and Exit Setup ............................................................................... 245
D.2.4.7 Exit without Saving................................................................................ 245
Page XI
WSB-9452 PICMG 1.0 CPU Card
D.2.5 Install the OS................................................................................................. 246
E
HAZARDOUS MATERIALS DISCLOSURE ................................................... 247
E.1 HAZARDOUS MATERIAL DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ..................................... 248
F
INDEX.................................................................................................................... 251
Page XII
WSB-9452 PICMG 1.0 CPU Card
List of Figures
Figure 1-1: Data Flow Block Diagram..........................................................................4
Figure 2-1: Data Flow Block Diagram........................................................................16
Figure 4-1: ATX–12V Connector Location ................................................................35
Figure 4-2: Audio Connector Location......................................................................36
Figure 4-3: Backplane to Mainboard Power Connector Location ..........................38
Figure 4-4: Battery Connector Location ...................................................................39
Figure 4-5: CPU Fan Connector Location.................................................................41
Figure 4-6: DIO Connector Location .........................................................................42
Figure 4-7: DVI Connector Location..........................................................................44
Figure 4-8: FDD Connector Location ........................................................................46
Figure 4-9: Front Panel Connector Location ............................................................48
Figure 4-10: IDE Connectors Location......................................................................49
Figure 4-11: Inverter Connector Location.................................................................51
Figure 4-12: IrDA Interface Connector Location ......................................................52
Figure 4-13: Keyboard Connector Location .............................................................54
Figure 4-14: LVDS Connector Location ....................................................................55
Figure 4-15: Parallel Port Connector Location.........................................................57
Figure 4-16: PCI Express Mini Card Connector Location .......................................60
Figure 4-17: RS-232 Serial Port Connector Location ..............................................62
Figure 4-18: SATA Connectors Location ..................................................................64
Figure 4-19: TPM Connector Location ......................................................................66
Figure 4-20: TV Out Connector Location ..................................................................68
Figure 4-21: USB Port Connector Location ..............................................................69
Figure 4-22: External Peripheral Interface Connector Panel ..................................70
Figure 4-23: RJ-45 Ethernet Connector ....................................................................72
Figure 4-24: Mini-DIN 6 PS/2 Connector ...................................................................73
Figure 4-25: VGA Connector ......................................................................................74
Figure 5-1: Make sure the CPU socket retention screw is unlocked .....................82
Page XIII
WSB-9452 PICMG 1.0 CPU Card
Figure 5-2: Lock the CPU Socket Retention Screw .................................................83
Figure 5-3: IEI CF-479B-RS Cooling Kit ....................................................................83
Figure 5-4: Install Support Bracket ...........................................................................84
Figure 5-5: Align the Cooling Kit ...............................................................................85
Figure 5-6: Secure the Cooling Kit ............................................................................86
Figure 5-7: Installing the DIMM Module ....................................................................88
Figure 5-8: Connection of IDE Connector.................................................................91
Figure 5-9: SATA Drive Cable Connection ...............................................................93
Figure 5-10: SATA Drive Connection ........................................................................94
Figure 5-11: Dual RS-232 Cable Installation .............................................................95
Figure 5-12: USB Cable Installation ..........................................................................96
Figure 5-13 Jumper .....................................................................................................97
Figure 5-14: AT Power Select Jumper Location.......................................................98
Figure 5-15: Clear CMOS Jumper ........................................................................... 100
Figure 5-16: LVDS Voltage Selection Jumper Pinout Locations......................... 102
Figure 5-17: LAN Power Selection Jumper Location ........................................... 103
Figure 7-1: InstallShield Wizard Preparation Screen............................................ 177
Figure 7-2: Welcome Screen ................................................................................... 177
Figure 7-3: License Agreement............................................................................... 178
Figure 7-4: Readme Information ............................................................................. 179
Figure 7-5: Restart the Computer ........................................................................... 180
Figure 7-6: Starting Install Shield Wizard Screen ................................................. 181
Figure 7-7: Preparing Setup Screen ....................................................................... 182
Figure 7-8: VGA Driver Installation Welcome Screen........................................... 183
Figure 7-9: VGA Driver License Agreement .......................................................... 184
Figure 7-10: VGA Driver Installing Notice.............................................................. 184
Figure 7-11: VGA Driver Installation Complete ..................................................... 185
Figure 7-12: Access Windows Control Panel ........................................................ 186
Figure 7-13: Double Click the System Icon ........................................................... 187
Figure 7-14: Double Click the Device Manager Tab.............................................. 188
Figure 7-15: Device Manager List ........................................................................... 188
Figure 7-16: Search for Suitable Driver.................................................................. 189
Page XIV
WSB-9452 PICMG 1.0 CPU Card
Figure 7-17: Locate Driver Files.............................................................................. 190
Figure 7-18: Location Browsing Window............................................................... 191
Figure 7-19: 4-AUDIO\AC-KIT883HD\Windows Folder.......................................... 193
Figure 7-20: HD Audio Driver Setup Extracting Files ........................................... 194
Figure 7-21: HD Audio Driver Setup Welcome Screen ......................................... 195
Figure 7-22: HD Audio Driver Installation Complete ............................................ 196
Figure 7-23: CD 4-AUDIO\AC-KIT08R\Windows Folder ........................................ 198
Figure 7-24: AC`97 Audio Driver Install Shield Wizard Starting .......................... 198
Figure 7-25: AC`97 Audio Driver Setup Preparation............................................. 199
Figure 7-26: AC`97 Audio Driver Welcome Screen............................................... 200
Figure 7-27: AC`97 Audio Driver Software Configuration.................................... 201
Figure 7-28: AC`97 Audio Driver Digital Signal ..................................................... 202
Figure 7-29: AC`97 Audio Driver Installation Begins............................................ 203
Figure 7-30: AC`97 Audio Driver Installation Complete ....................................... 204
Page XV
WSB-9452 PICMG 1.0 CPU Card
List of Tables
Table 1-1: WSB-9452 Model Variations .......................................................................2
Table 1-2: Technical Specifications ............................................................................8
Table 2-1: Supported CPUs ........................................................................................10
Table 2-2: Power Consumption..................................................................................22
Table 3-1: Package List Contents..............................................................................28
Table 3-2: Package List Contents..............................................................................29
Table 4-1: Connector and Jumper Locations ...........................................................31
Table 4-2: Peripheral Interface Connectors..............................................................33
Table 4-3: External Peripheral Interface Connectors ..............................................33
Table 4-4: On-board Jumpers ....................................................................................34
Table 4-5: ATX–12V Connector Pinouts....................................................................35
Table 4-6: Audio Connector Pinouts .........................................................................37
Table 4-7: Backplane to Mainboard Power Pin Outs ...............................................38
Table 4-8: Battery Connector Pinouts.......................................................................40
Table 4-9: CPU Fan Connector Pinouts ....................................................................41
Table 4-10: DIOConnector Pinouts............................................................................43
Table 4-11: DVI Connector Pinouts ...........................................................................45
Table 4-12: FDD Connector Pinouts..........................................................................47
Table 4-13: Front Panel Connector Location............................................................48
Table 4-14: IDE Connector Pinouts ...........................................................................50
Table 4-15: Inverter Connector Pinouts ....................................................................51
Table 4-16: IrDA Interface Connector Pinouts..........................................................53
Table 4-17: KB1 Connector Pinouts ..........................................................................54
Table 4-18: LVDS Connector Pinouts........................................................................56
Table 4-19: Parallel Port Connector Pinouts ............................................................58
Table 4-20: PCI Express Mini Card Connector Pinouts...........................................61
Table 4-21: RS-232 Serial Port Connector Pinouts..................................................63
Table 4-22: SATA Connectors Pinouts .....................................................................64
Page XVI
WSB-9452 PICMG 1.0 CPU Card
Table 4-23: TPM Connector Pinouts..........................................................................67
Table 4-24: TV Out Connector Pinouts .....................................................................68
Table 4-25: USB Port Connector Pinouts .................................................................70
Table 4-26: LAN Pinouts .............................................................................................71
Table 4-27: Ethernet Connector Pinouts...................................................................71
Table 4-28: Mini-DIN 6 PS/2 Connector .....................................................................73
Table 4-29: USB Port Pinouts.....................................................................................74
Table 4-30: VGA Connector Pinouts .........................................................................75
Table 5-1: IEI Provided Cables ...................................................................................89
Table 5-2: On-board Jumpers ....................................................................................97
Table 5-3: AT Power Select Jumper Settings ...........................................................98
Table 5-4: Clear CMOS Jumper Settings ..................................................................99
Table 5-5: LVDS LCD Voltage Selection Jumper Settings ................................... 101
Table 5-6: LCD Voltage Selection Jumper Settings.............................................. 103
Table 6-1: BIOS Navigation Keys............................................................................ 107
Page XVII
WSB-9452 PICMG 1.0 CPU Card
List of BIOS Menus
BIOS Menu 1: Main................................................................................................... 108
BIOS Menu 2: Advanced.......................................................................................... 110
BIOS Menu 3: CPU Configuration........................................................................... 111
BIOS Menu 4: IDE Configuration ............................................................................ 113
BIOS Menu 5: IDE Master and IDE Slave Configuration....................................... 115
BIOS Menu 6: Floppy Configuration ...................................................................... 119
BIOS Menu 7: Super IO Configuration ................................................................... 120
BIOS Menu 8: Hardware Health Configuration...................................................... 124
BIOS Menu 9: ACPI Configuration.......................................................................... 127
BIOS Menu 10: General ACPI Configuration ......................................................... 128
BIOS Menu 11: APM Configuration ........................................................................ 130
BIOS Menu 12: MPS Configuration ........................................................................ 133
BIOS Menu 13: Remote Access Configuration ..................................................... 134
BIOS Menu 14: Trusted Computing Configuration ............................................... 139
BIOS Menu 15: USB Configuration......................................................................... 140
BIOS Menu 16: PCI/PnP Configuration .................................................................. 145
BIOS Menu 17: Boot................................................................................................. 151
BIOS Menu 18: Boot Settings Configuration......................................................... 152
BIOS Menu 19: Boot Device Priority Settings ....................................................... 155
BIOS Menu 20: Hard Disk Drives ............................................................................ 156
BIOS Menu 21: Removable Drives.......................................................................... 158
BIOS Menu 22: Security........................................................................................... 159
BIOS Menu 23: Chipset............................................................................................ 161
BIOS Menu 24: Northbridge Chipset Configuration ............................................. 162
BIOS Menu 25: Video Function Configuration ...................................................... 165
BIOS Menu 26:Southbridge Chipset Configuration.............................................. 170
BIOS Menu 27:Exit ................................................................................................... 173
Page XVIII
WSB-9452 PICMG 1.0 CPU Card
Chapter
1
1 Introduction
Page 1
WSB-9452 PICMG 1.0 CPU Card
1.1 WSB-9452 CPU Card Overview
The PICMG 1.0 form factor WSB-9452 CPU card with Intel® Core™2 Duo/ Intel® Core™
Duo/ Intel® Core™ Solo / Intel® Celeron® M processor platform is fully equipped with the
latest technology and advanced multi-mode I/Os. The WSB-9452 is designed for system
manufacturers, integrators, and VARs that want performance, reliability, and quality at a
reasonable price.
1.1.1 WSB-9452 Model Variations
The WSB-9452 has four model variations shown in Table 1-1.
Model Name
SATA
SATA II
IDE
Digital Video Interface (DVI)
WSB-9452-R20
Two
--
One
None
WSB-9452S-R20
Two
Two
Two
None
WSB-9452DVI-R20
Two
--
One
One
WSB-9452SDVI-R20
Two
Two
Two
One
Table 1-1: WSB-9452 Model Variations
1.1.2 WSB-9452 CPU Card Applications
The WSB-9452 CPU card has been designed for use in industrial applications where
board expansion is critical and operational reliability is essential.
1.1.3 WSB-9452 CPU Card Benefits
Some of the WSB-9452 CPU card benefits include:
Dual-core Intel® processor support
o
o
Two physical cores in a package share the system load
Each core has its own L1 cache and shares the L2 cache to enhance the
processing speed
o
High performance levels especially in 3D graphic and multi media
application
Page 2
WSB-9452 PICMG 1.0 CPU Card
PCI Express® Mini Card support
o
Small form factor (half the size of a mini-PCI card) allows easy integration
and addresses system manufacturers' needs for build-to-order (BTO) and
configure-to-order (CTO) applications
providing access to multiple PCI and ISA expansion slots for easy system
expansion
operating reliably in harsh industrial environments with ambient temperatures
as high as 60°C
rebooting automatically if the BIOS watchdog timer detects that the system is
no longer operating
1.1.4 WSB-9452 CPU Card Features
Some of the WSB-9452 CPU card features are listed below:
PICMG 1.0 compliant
RoHS compliant
Intel® Core™2 Duo/ Intel® Core™ Duo/ Intel® Core™ Solo / Intel® Celeron® M
CPUs supported
PCI Express® Mini Card supported
Maximum front side bus (FSB) speed of 667MHz supported
Up to 4GB of 400/533/667MHz dual channel DDR2 memory supported
Analog display supported
One dual channel 24-bit LVDS port
One DVI interface with resolution from VGA to UXGA supported by two
models (see Table 1-1)
Two high performance PCI Express Gigabit Ethernet (PCI-E GbE) controllers
supported
SATA II channels with transfer rates up to 300 MB/s are supported (see Table
1-1)
Supports up to seven USB 2.0 devices
RAID 0 and RAID 1 functionalities (SATA3 and SATA4 only) supported (see
Table 1-1)
Page 3
WSB-9452 PICMG 1.0 CPU Card
1.2 WSB-9452 CPU Card Overview
* See Table 1-1 for supported models.
Figure 1-1: Data Flow Block Diagram
Page 4
WSB-9452 PICMG 1.0 CPU Card
1.2.1 WSB-9452 CPU Card Connectors
The WSB-9452 CPU card has the following connectors on-board:
1 x ATX-12V connector
1 x Audio module connector
1 x Backplane to mainboard power connector
1 x Battery connector
1 x CPU fan connector
1 x Digital I/O connector
1 x Digital Visual Interface (DVI) Connector (see Table 1-1)
1 x FDD connector
1 x Front panel connector
2 x 40-pin IDE connectors (see Table 1-1)
1 x Inverter connector
1 x IrDA connector
1 x Keyboard connector
1 x LVDS connector
1 x Parallel port connector
1 x PCI Express® Mini Card connector
2 x RS-232 Serial port connectors
4 x SATA connectors (see Table 1-1)
1 x TPM connector
1 x TV out connector
6 x USB connectors
The location of these connectors on the CPU card can be seen in Figure 1-1. These
connectors are fully described in Chapter 4.
Page 5
WSB-9452 PICMG 1.0 CPU Card
1.2.2 Technical Specifications
WSB-9452 CPU card technical specifications are listed in Table 1-2. Detailed descriptions
of each specification can be found in Chapter 2.
SPECIFICATION
Supported CPUs
DESCRIPTION
Intel® Core™2 Duo
Intel® Core™ Duo
Intel® Core™ Solo
Intel® Celeron® M
Socket
Socket M Micro-FCPGA
Chipsets
Northbridge: Intel® 945GME
Southbridge: Intel® ICH7-M
Graphics Support
Memory
Intel® Graphics Media Accelerator 950 (GMA 950)
o
One VGA
o
One DVI (See Table 1-1)
o
One LVDS
Two 400/533/667 MHz DDR2 memory modules
(Max. 4GB)
PCI Bus Interface
33MHz, Revision 2.3
ISA Bus Interface
Supports three fully compatible ISA slots without
buffering
ISA DMA and ISA Bus Master function are not
supported
Serial ATA (SATA)
Two SATA channels
or
Two SATA channels and two SATA II channels
Page 6
WSB-9452 PICMG 1.0 CPU Card
SPECIFICATION
DESCRIPTION
HDD Interface
One IDE channel supports two Ultra ATA 100/66/33
devices (see Table 1-1)
Two IDE channels support four Ultra ATA 100/66/33
devices (see Table 1-1)
Floppy Disk Drive (FDD)
Supports FDD
USB Interfaces
Six internal USB 2.0 connectors and one external USB
port support seven USB devices
Serial Ports
Two RS-232 serial port connectors (COM1 and COM2)
Real Time Clock
256-byte battery backed CMOS RAM
Hardware Monitoring
Cooling fans, temperature and system voltages
Power Management
Supports Advanced Configuration and Power Interface
(ACPI) Specifications Revision 2.0
Power Consumption
5V @ 4.15A, +12V @ 1.29A (Intel® Core™ Duo 2GHz
with two 1GB DDR2 667MHz)
Infrared Support
One Infrared Data Association (IrDA) interface
Ethernet
Two PCI Express Gigabit Ethernet (PCI-E GbE)
channels
BIOS
AMI BIOS
Physical Dimensions
12.2cm x 34.1cm (width x length)
Operating Temperature
Minimum: 0ºC (32°F)
Maximum: 60°C (140°F)
Page 7
WSB-9452 PICMG 1.0 CPU Card
SPECIFICATION
DESCRIPTION
Operating Humidity
Minimum: 5%
Maximum: 95%
Optional Audio Interface
Realtek ALC655/883 with AC `97 / HD Audio
Table 1-2: Technical Specifications
Page 8
WSB-9452 PICMG 1.0 CPU Card
Chapter
2
2 Detailed Specifications
Page 9
WSB-9452 PICMG 1.0 CPU Card
2.1 Compatible IEI Backplanes
The WSB-9452 CPU card is compatible with the all IEI PICMG1.0 backplanes. For more
information on these backplanes, visit the IEI website or contact your CPU card reseller or
vendor.
2.2 CPU Support
Model
Capacity
Interface
FSB
Intel® Core™2 Duo T7600
2.33GHz
478
667MHz
Intel® Core™ Duo T2700
2.33GHz
478
533/667MHz
Intel® Core™ Solo T1400
1.83GHz
478
533/667MHz
Intel® Celeron® M 450
2.0GHz
478
533 MHz
Table 2-1: Supported CPUs
2.2.1 Intel® Core™2 Duo
The Intel® Core™2 Duo processor comes with the following features:
Dual core processor with enhanced performance
Intel® 64 architecture
Supports Intel® Architecture with Dynamic Execution
On-die, primary 32kB instruction cache and 32kB write-back data cache per
core
On-die, up to 4MB second level shared cache with Advanced Transfer Cache
Architecture
Data Prefetch Logic
667MHz, Source-Synchronous FSB for Standard Voltage processors
Advanced Power Management features including Enhanced Intel SpeedStep®
Technology
Intel® Enhanced Deeper Sleep state and Dynamic Cache Sizing
Page 10
WSB-9452 PICMG 1.0 CPU Card
2.2.2 Intel® Core™ Duo
The Intel® Core™ Duo processor comes with the following features:
Two complete execution cores in one processor package provide
advancements in simultaneous computing
Dual-core processing efficiently delivers performance while balancing power
requirements
Two execution cores share a high-performance, power-optimized 667 MHz
front-side bus (FSB) to access the same chipset memory.
Enhanced Intel SpeedStep® technology allows a system to dynamically adjust
processor voltage and core frequency, decreasing average power
consumption and average heat production
Intel® Smart Cache Design allows two execution cores to share 2 MB of L2
cache, reducing FSB traffic and enhancing system responsiveness
Intel® Advanced Thermal Manager supports new digital temperature sensors
and thermal monitors on each execution core to enhance thermal monitoring
accuracy
Streaming SIMD Extensions 3 (SSE3) provides significant performance
enhancement for multi-media applications
Embedded lifecycle support protects system investment by enabling extended
product availability for embedded and communications customers
®
2.2.3 Intel Core™ Solo
The Intel® Core™ Solo processor comes with the following features:
Supports Intel Architecture with Dynamic Execution
On-die, primary 32-KB instruction cache and 32-KB write-back data cache
On-die, 2-MB second level cache with Advanced Transfer Cache Architecture
Streaming SIMD Extensions 2 (SSE2) and Streaming SIMD Extensions 3
(SSE3)
Advanced power management features including Enhanced Intel SpeedStep®
technology
Page 11
WSB-9452 PICMG 1.0 CPU Card
Execute Disable Bit support for enhanced security
Intel® Virtualization Technology enhances virtualization robustness and
performance
2.2.4 Intel® Celeron® M
The Intel® Celeron® M CPU comes with the following features:
Processor low-power states C1, C2 and C3 (Deep Sleep) lowers CPU power
consumption/dissipation to conserve battery life
Micro FCPGA packaging technology optimized for a range of thinner, lighter
designs, including <1" thick
Support for Intel® Mobile Voltage Positioning (Intel® MVP IV) dynamically
lowers voltage based on processor activity to lower thermal design power,
enabling smaller notebooks
Lower core voltage – 1.356 V low-voltage operation and 24.5W thermal
design power lower thermal dissipation enabling thinner notebooks
Intel® Streaming SIMD Extensions accelerates 3D graphics performance
Execute Disable Bit Technology prevents certain classes of malicious "buffer
overflow" attacks when combined with a supporting operating system.
2.3 On-board Chipsets
2.3.1 Northbridge and Southbridge Chipsets
The following chipsets are preinstalled on the board:
Northbridge: Intel® 945GME
Southbridge: Intel® ICH7-M
The following two sections (Section 2.3.2 and Section 2.3.3) lists some of the features of
the Intel® 945GME and the Intel® ICH7-M chipsets. For more information on these two
chipsets refer to the Intel website.
2.3.2 Intel® 945GME Northbridge Chipset
The Intel® 945GME Northbridge chipset comes with the following features:
Page 12
WSB-9452 PICMG 1.0 CPU Card
System Memory Support
o
o
o
o
o
Supports single/dual-channel DDR2 SDRAM
64-bit wide per channel
256MB, 512MB, 1GB and 2GB memory technologies supported
Support for DDR2 On-Die Termination (ODT)
Support for 2N timings only
Internal Graphics
o
o
Intel® Gen 3.5 Integrated Graphics Engine
250 MHz core render clock and 200 MHz core display clock at 1.05 V
core voltage
o
Supports TV-Out, LVDS, CRT and SDVO
DMI
o
o
o
o
Chip-to-chip interface between (G)MCH and ICH
Configurable as x2 or x4 DMI lanes
DMI lane reversal support
32-bit downstream address
Power Management
o
o
o
ACPI S0, S3, S4, S5
CPU States C0, C1, C2, C3, C4 states
Rapid Memory Power Management
2.3.3 Intel ICH7-M Southbridge Chipset
The Intel® ICH7-M Southbridge chipset comes with the following features:
PCI Local Bus Specification, Revision 2.3 support for 33MHz PCI operations
(supports up to six Req/Gnt pairs)
ACPI Power Management Logic support
Enhanced DMA controller, interrupt controller, and timer functions
Integrated Serial ATA host controller with independent DMA operation on two
ports and AHCI
Integrated IDE controller supports Ultra ATA 100/66/33
USB host interface with support for eight USB ports; four UHCI host controller;
one EHCI high-speed USB 2.0 Host controller
Supports Audio Codec ’97, Revision 2.3 Specification
Supports Intel® High Definition Audio
Page 13
WSB-9452 PICMG 1.0 CPU Card
Supports Intel® Matrix Storage Technology
Supports Intel® Active Management Technology
Low Pint Count (LPC) interface
Firmware Hub (FWH) interface support
Serial Peripheral Interface (SPI) support
2.4 Graphics Support
2.4.1 Intel® GMA 950
The Intel® GMA 950 integrated on the Intel® 945GME chipset has the following features.
®
Intel GMA 950 Graphics Core
o
o
400MHz 256-bit graphics core
Up to 10.6 GB/sec memory bandwidth with DDR2 667 MHz system
memory
o
o
o
o
o
1.6 GPixels/sec and 1.6 GTexels/sec fill rate
192 MB maximum video memory
2048 x 1536 at 75 Hz maximum resolution
Dynamic Display Modes for flat-panel, wide-screen and Digital TV support
Operating systems supported: Microsoft® Windows® XP, Windows® XP
64-bit, Media Center Edition, Windows 2000; Linux-compatible (Xfree86
source available)
High Performance 3D
o
o
o
o
o
Up to 4 pixels per clock rendering
Microsoft® DirectX® 9 Hardware Acceleration Features:
Pixel Shader 2, Volumetric Textures, Shadow Maps,
Slope Scale Depth Bias, Two-Sided Stencil
Microsoft® DirectX® 9 Vertex Shader 3.0 and Transform and Lighting
supported in SW through highly optimized
o
o
o
Processor Specific Geometry Pipeline (PSGP)
Texture Decompression for DirectX® and OpenGL®
OpenGL® 1.4 support with ARB extensions
Advanced Display Technology
o
Page 14
Consumer Electronic display (Digital TV) support
WSB-9452 PICMG 1.0 CPU Card
o
Two Serial Digital Video Out (SDVO) ports for flat-panel monitors and/or
TV-out support via ADD2 cards
o
Support for Intel Media Expansion Cards, providing TV out and PVR
capability
o
Interlaced Display output support
High Quality Media Support
o
High Definition Hardware Motion Compensation to support HD hi-bitrate
MPEG2 media playback
o
o
o
Up and Down Scaling of Video Content
HD Content Decode – up to two stream support
5x3 Overlay Filtering
2.4.2 Analog VGA
The on-board analog VGA has the following features.
Supports 400MHz, 24-bit RAMDAC (RAM digital to analog converter)
Supports displays with resolutions up to 2048x1536 pixels
2.4.3 Digital LVDS
The on-board digital LVDS has the following features.
Supports dual-channel 24-bit LVDS for TFT Panels up to UXGA/WUXGA
Compliant with ANSI/TIA/EIA-644-2001 SPEC.
2.4.4 Digital Visual Interface (DVI)
The DVI interface on supported models (see Table 1-1) has the following features.
Supports DVI 1.0 up to UXGA with Silcon Image PanelLink® Technology
Page 15
WSB-9452 PICMG 1.0 CPU Card
2.5 Data Flow
Figure 2-1 shows the data flow between the user-installed socket 478 CPU, the two
on-board chipsets and other components installed on the CPU card are described in the
following sections of this chapter.
Figure 2-1: Data Flow Block Diagram
Page 16
WSB-9452 PICMG 1.0 CPU Card
2.6 Memory Support
WARNING:
When installing a memory module, make sure a DDR2 memory module
is used. A DDR memory module may cause permanent damage to the
system and severe injury to the user.
The WSB-9452 CPU has two 240-pin dual inline memory module (DIMM) sockets that
support up to two unbuffered DDR2 DIMMs with the following specifications:
Maximum RAM: 4GB (2GB module in each slot)
DIMM Transfer Rates: 667MHz, 533MHz, 400MHz
Up to 10.6 GB/sec memory bandwidth
2.7 PCI Bus Interface Support
The PCI bus on the WSB-9452 CPU card has the following features:
NOTE:
The WSB-9452 does not support ISA DMA and ISA Bus Master
function. Before purchasing your ISA device, please confirm with your
vendor that your ISA card is supported by the CPU board.
33MHz Revision 2.3 is implemented
Up to four external bus masters are supported
2.X ISA bus interface supported
Three fully compatible ISA slots without buffering supported
Page 17
WSB-9452 PICMG 1.0 CPU Card
2.8 GbE Ethernet Connection
The two GbE controllers (Broadcom BCM5787) on the WSB-9452 CPU card connect to
two 10/100/1000Mb/s Ethernet RJ-45 LAN ports on the rear panel. The BCM5787 is a
seventh generation 10/100/1000BASE-T Ethernet LAN controller solution for high
performance network applications. The device combines a triple-speed IEEE 802.3
compliant Media Access Controller (MAC) with a triple-speed Ethernet transceiver, PCIe
bus interface, and on-chip buffer memory in a single device. The device is fabricated in a
1.2V CMOS process providing a low-power system solution. The GbE controllers come
with the following features:
Integrated 10/100/1000 transceiver
10/100/1000 full/half-duplex MAC
Automatic MDI crossover function
Supports PCIe v1.0a
Wake-on-LAN support meeting the ACPI requirements
Statistics for SNMP MIB II, Ethernet-like MIB and Ethernet MIB (802.3z,
clause 30)
Serial EEPROM or serial flash supported
JTAG supported
196-FBGA package
2.9 Drive Interfaces
The WSB-9452 and WSB-9452DVI models support the following drive interfaces:
2 x SATA drives
1 x IDE channel supports two Ultra ATA 100/66/33 devices
1 x FDD
The WSB-9452S and WSB-9452SDVI models support the following drive interfaces:
2 x SATA drives
2 x SATA II drives (Jmicron JMB363 chipset supports SATA3/SATA4 with
RAID 0, RAID 1, and JBOD configurations)
2 x IDE channels support four Ultra ATA 100/66/33 devices
Page 18
WSB-9452 PICMG 1.0 CPU Card
1 x FDD
2.9.1 SATA Drives
The WSB-9452 and WSB-9452DVI models support the following SATA drive interfaces:
2 x SATA drives with transfer rates up to 150 MB/s with the ICH7-M
Southbridge chipset
The WSB-9452S and WSB-9452SDVI models support the following SATA drive
interfaces:
2 x SATA drives with transfer rates up to 150 MB/s with the ICH7-M
Southbridge chipset
2 x SATA II drives with transfer rates up to 300 MB/s with the Jmicron JMB363
chipset
2.9.2 IDE HDD Interfaces
The IDE controller on the ICH7-M Southbridge chipset integrated on the CPU card
supports two HDDs (WSB-9452 and WSB-9452DVI models) or four HDDs (WSB-9452S
and WSB-9452SDVI models) with the following specifications:
Supports PIO IDE transfers up to 16MB/s
Supports the following Ultra ATA devices:
o
o
o
Ultra ATA/33, with data transfer rates up to 33MB/s
Ultra ATA/66, with data transfer rates up to 66MB/s
Ultra ATA/100, with data transfer rates up to 100MB/s
2.9.3 Floppy Disk Drive (FDD)
The WSB-9452 CPU card supports a single FDD. The following FDD formats are
compatible with the board.
5.25”: 360KB and 1.2MB
3.5”: 720KB, 1.44MB and 2.88MB
Page 19
WSB-9452 PICMG 1.0 CPU Card
2.10 SATA II and RAID Functionality (SATA3 and SATA4 only)
Two SATA II channels and their associated RAID functionality are only available on the
WSB-9452S and WSB-9452SDVI models. These models come with an on-board Jmicron
JMB363 PCI-E to two-port SATA II and one-port parallel ATA (PATA) host controller. The
Jmicron JMB363 supports the following SATA II / PATA features:
Two-port 300 MB/s SATA II interface
Two independent SATA II channels (separate logic and FIFO)
Native Command Queue (NCQ) on SATA II port
Hot Plugging like USB on SATA II port
SATA II Gen1m and Gen2m (External SATA Connection, eSATA)
Port Multiplier with Command-based Switching on SATA II port
Up to UDMA6 PATA transfer mode
Up to four storage device connection
RAID 0, 1, 0+1, JBOD configuration
2.11 Serial Ports
The WSB-9452 CPU card has two high-speed UART serial ports, configured as COM1
and COM2. The serial ports have the following specifications.
16C550 UART with 16-byte FIFO buffer
115.2Kbps transmission rate
2.12 Real Time Clock
256-byte battery backed CMOS RAM
Page 20
WSB-9452 PICMG 1.0 CPU Card
2.13 System Monitoring
The WSB-9452 CPU card is capable of self-monitoring various aspects of its operating
status including:
CPU, chipset, and battery voltage, +3.3V, +5V, and +12V
RPM of cooling fans
CPU and board temperatures (by the corresponding embedded sensors)
2.14 Infrared Data Association (IrDA) Interface
The WSB-9452 CPU card IrDA supports the following interfaces.
Serial Infrared (SIR)
Amplitude Shift Keyed Infrared (ASKIR)
If you want to use the IrDA port, you have to configure SIR or ASKIR mode in the BIOS
under Super IO devices. The normal RS-232 COM2 will be disabled.
2.15 USB Interfaces
The WSB-9452 CPU card has seven USB interfaces, six internal and one external. The
USB interfaces support USB 2.0.
2.16 BIOS
The WSB-9452 CPU card uses a licensed copy of AMI BIOS. The features of the flash
BIOS used are listed below:
SMIBIOS (DMI) compliant
Console redirection function support
PXE (Pre-Boot Execution Environment) support
USB booting support
Page 21
WSB-9452 PICMG 1.0 CPU Card
2.17 Operating Temperature and Temperature Control
The maximum and minimum operating temperatures for the WSB-9452 CPU card are
listed below.
Minimum Operating Temperature: 0ºC (32°F)
Maximum Operating Temperature: 60°C (140°F)
A cooling fan and heat sink must be installed on the CPU. Thermal paste must be
smeared on the lower side of the heat sink before it is mounted on the CPU. Heat sinks
are also mounted on the Northbridge and Southbridge chipsets to ensure the operating
temperature of these chips remain low.
2.18 Optional Audio Interface
The WSB-9452 CPU card does not come with an on-board Codec but the Intel® ICH7-M
chipset has an Audio Codec (AC’97 / HDA) controller. A connector on the CPU card can
be used to connect the ICH7-M audio controllers to an external Codec.
2.19 Power Consumption
Table 2-2 shows the power consumption parameters for the WSB-9452 CPU card when a
2GHz Intel® Core™ Duo processor is running with two 1GB DDR2 667MHz SDRAM
memory modules.
Voltage
Current
5V
4.15A
+12V
1.29A
Table 2-2: Power Consumption
Page 22
WSB-9452 PICMG 1.0 CPU Card
2.20 Packaged Contents and Optional Accessory Items
2.20.1 Package Contents
When you unpack the WSB-9452 CPU card you should find the following components.
1 x WSB-9452 single board computer
1 x Mini jumper pack
1 x ATA 66/100 flat cable
1 x Dual RS-232 cable
2 x SATA cables
1 x SATA power cable
1 x Keyboard/ PS2 mouse Y cable
1 x USB cable
1 x Utility CD
1 x QIG (quick installation guide)
2.20.2 Special Items
The following additional items are shipped with the WSB-9452S and WSB-9452SDVI CPU
card models.
2 x SATA cables
1 x SATA power cable
Page 23
WSB-9452 PICMG 1.0 CPU Card
2.20.3 Optional Accessory Items
The items shown in the list below are separately purchased optional accessory items.
DVI cable
Audio Kit
CPU Cooler
FDD cable
LPT cable
Page 24
WSB-9452 PICMG 1.0 CPU Card
Chapter
3
3 Unpacking
Page 25
WSB-9452 PICMG 1.0 CPU Card
3.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during the installation of the
WSB-9452 may result in permanent damage to the WSB-9452 and
severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the WSB-9452. Dry climates are especially susceptible to ESD. It is therefore
critical that whenever the WSB-9452, or any other electrical component is handled, the
following anti-static precautions are strictly adhered to.
Wear an anti-static wristband: - Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
Self-grounding:- Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
Use an anti-static pad: When configuring the WSB-9452, place it on an
antic-static pad. This reduces the possibility of ESD damaging the WSB-9452.
Only handle the edges of the PCB:-: When handling the PCB, hold the PCB
by the edges.
3.2 Unpacking
3.2.1 Unpacking Precautions
When the WSB-9452 is unpacked, please do the following:
Follow the anti-static precautions outlined in Section 3.1.
Make sure the packing box is facing upwards so the WSB-9452 does not fall
out of the box.
Make sure all the components shown in Section 3.3 are present.
Page 26
WSB-9452 PICMG 1.0 CPU Card
3.3 Unpacking Checklist
NOTE:
If some of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact the IEI reseller or
vendor you purchased the WSB-9452 from or contact an IEI sales
representative directly. To contact an IEI sales representative, please
send an email to [email protected]
3.3.1 Package Contents
The WSB-9452 is shipped with the following components:
Quantity
Item and Part Number
1
WSB-9452 CPU Card
1
ATA 66/100 flat cable
Image
(P/N: 32200-000052-RS)
1
Dual RS-232 cable
(P/N: 19800-000051-RS)
Page 27
WSB-9452 PICMG 1.0 CPU Card
1
IO-KIT (DVI model only)
(P/N:IO-KIT-001)
1
KB/MS PS/2 Y-cable
(P/N: 32000-000138-RS)
2
SATA cables
(P/N: 32000-062800-RS)
1
SATA power cables
(P/N: 32100-088600-RS)
1
Mini jumper Pack
1
Quick Installation Guide
1
Utility CD
1
USB cable
(P/N: CB-USB02-RS)
Table 3-1: Package List Contents
Page 28
WSB-9452 PICMG 1.0 CPU Card
3.4 Optional Items
CPU cooler
(P/N: CF-479B-RS)
Audio kit
(P/N: AC-KIT-833HD-R10)
Audio kit_ 5.1 Channel
(P/N: AC-KIT08R-R10)
ATX 12V Cable
(P/N: 32100-087100-RS)
FDD cable
(P/N:32200-000017-RS)
LPT cable
(P/N:19800-000049-RS)
Table 3-2: Package List Contents
Page 29
WSB-9452 PICMG 1.0 CPU Card
Chapter
4
4 Connectors and
Jumpers
Page 30
WSB-9452 PICMG 1.0 CPU Card
4.1 Peripheral Interface Connectors
The locations of the peripheral interface connectors are shown in Section 4.1.1. A
complete list of all the peripheral interface connectors can be seen in Section 4.2.
4.1.1 WSB-9452 CPU card Layout
Table 4-1 shows the on-board peripheral connectors, backplane peripheral connectors
and on-board jumpers.
Table 4-1: Connector and Jumper Locations
Page 31
WSB-9452 PICMG 1.0 CPU Card
4.1.2 Peripheral Interface Connectors
Table 4-2 lists the peripheral interface connectors on the WSB-9452 CPU card. Detailed
descriptions of these connectors can be found in Section 4.2.
Label
Connector
Type
CPU12V1
ATX-12V CPU Power Source
4-pin terminal block
J_AUDIO1
Audio Module Connector
10-pin header
ATXCTL1
Backplane to Mainboard Power Connector
3-pin wafer connector
BAT1
Battery Connector
2-pin wafer connector
CPU_FAN1
CPU Fan Connector
4-pin wafer connector
DIO1
Digital I/O Connector
10-pin header
DVI1
Digital Visual Interface Connector
25-pin header
FDD1
FDD Connector
34-pin box header
F_PANEL1
Front Panel Connector
14-pin header
IDE1, IDE2
IDE Connectors (Primary)
40-pin box header
INVERTER1
Inverter Connector
5-pin wafer connector
IR1
IrDA Infrared Interface Connector
5-pin header
KB1
Keyboard Connector
4-pin wafer connector
LVDS1
LVDS Panel Connector
30-pin crimp connector
LPT1
Parallel Port Connector
25-pin box header
CN1
PCI-Express Mini Card
52-pin PCIe Mini Card slot
COM1
RS-232 Serial Port Connectors
10-pin box header
COM1
RS-232 Serial Port Connectors
10-pin box header
SATA1
Serial ATA Connectors
7-pin SATA connector
Page 32
WSB-9452 PICMG 1.0 CPU Card
SATA2
Serial ATA Connectors
7-pin SATA connector
SATA3
Serial ATA Connectors
7-pin SATA connector
SATA4
Serial ATA Connectors
7-pin SATA connector
TPM1
Trusted Platform Module Connector
20-pin header
TV1
TV Out Connector
6-pin header
USB01
USB Connectors
8-pin header
USB23
USB Connectors
8-pin header
USB45
USB Connectors
8-pin header
Table 4-2: Peripheral Interface Connectors
4.1.3 External Peripheral Interface Connectors
Table 4-3 lists the external peripheral interface connectors on the WSB-9452. Detailed
descriptions of these connectors can be found in Section 4.3.
Connector
Type
Label
Ethernet connector
RJ-45 connector
LAN1
Ethernet connector
RJ-45 connector
LAN2
Keyboard/mouse connector
MINI-DIN connector
KB_MS1
USB connector
USB 2.0 connector
USB_C6
VGA connector
HD-D-sub 15 female connector
VGA1
Table 4-3: External Peripheral Interface Connectors
Page 33
WSB-9452 PICMG 1.0 CPU Card
4.1.4 On-board Jumpers
Table 4-4 lists the on-board jumpers. Detailed descriptions of these jumpers can be found
in Section 5.5.
Label
Connector
Type
J_CMOS1
CMOS state setting
3-pin header
J_LVDS1
L CD Voltage Selector
3-pin header
JAUTO1
AT/ATX mode select
2-pin header
JLAN_PWR1
LAN power select
6-pin header
Table 4-4: On-board Jumpers
4.2 Internal Peripheral Connectors
Internal peripheral connectors are found on the CPU card and are only accessible when
the CPU card is outside of the chassis. This section has complete descriptions of all the
internal peripheral connectors on the WSB-9452 CPU card.
4.2.1 ATX-12V Power Source Connector
CN Label:
CPU12V1
CN Type:
4-pin terminal block
CN Location:
See Figure 4-1
CN Pinouts:
See Table 4-5
This connector supports the ATX-12V power supply.
Page 34
WSB-9452 PICMG 1.0 CPU Card
Figure 4-1: ATX–12V Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
GND
3
+12V
4
+12V
Table 4-5: ATX–12V Connector Pinouts
Page 35
WSB-9452 PICMG 1.0 CPU Card
4.2.2 Audio Module Connector
CN Label:
J_AUDIO1
CN Type:
10-pin header
CN Location:
See Figure 4-2
CN Pinouts:
See Table 4-6
The WSB-9452 CPU card does not have a built-in AC’97 audio codec. If your system
needs audio then this connector must be connected to an external audio module
(AC-KIT-08R).
Figure 4-2: Audio Connector Location
Page 36
WSB-9452 PICMG 1.0 CPU Card
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
AC97_SYNC
2
AC97_BITCLK
3
AC97_SDOUT
4
AC97_PCBEEP
5
AC97_SDIN
6
AC97_RST#
7
AC97_VCC
8
AC97_GND
9
AC97_12V
10
AC97_GND
Table 4-6: Audio Connector Pinouts
4.2.3 Backplane to Mainboard Power Connector
CN Label:
ATXCTL1
CN Type:
3-pin wafer connector
CN Location:
See Figure 4-3
CN Pinouts:
See Table 4-7
Connects a power source from a backplane with an ATX Connector.
Page 37
WSB-9452 PICMG 1.0 CPU Card
Figure 4-3: Backplane to Mainboard Power Connector Location
PIN NO.
DESCRIPTION
1
Ground
2
PS_ON
3
5V Dual
Table 4-7: Backplane to Mainboard Power Pin Outs
Page 38
WSB-9452 PICMG 1.0 CPU Card
4.2.4 Battery Connector
CN Label:
BAT1
CN Type:
2-pin wafer connector
CN Location:
See Figure 4-4
CN Pinouts:
See Table 4-8
Figure 4-4: Battery Connector Location
Page 39
WSB-9452 PICMG 1.0 CPU Card
PIN NO. DESCRIPTION
1
BAT
2
GND
Table 4-8: Battery Connector Pinouts
4.2.5 CPU Fan Connector
CN Label:
CPU_FAN1
CN Type:
4-pin wafer connector
CN Location:
See Figure 4-5
CN Pinouts:
See Table 4-9
The cooling fan connector provides a 12V, 500mA current to a CPU cooling fan. The
connector has a "rotation" pin to get rotation signals from fans and notify the system so the
system BIOS can recognize the fan speed. Please note that only specified fans can issue
the rotation signals.
Page 40
WSB-9452 PICMG 1.0 CPU Card
Figure 4-5: CPU Fan Connector Location
PIN
DESCRIPTION
1
Ground
2
+12V
3
Rotation Signal
4
Control
Table 4-9: CPU Fan Connector Pinouts
Page 41
WSB-9452 PICMG 1.0 CPU Card
4.2.6 Digital Input/Output (DIO) Connector
CN Label:
DIO1
CN Type:
10-pin header
CN Location:
See Figure 4-6
CN Pinouts:
See Table 4-10
The DIO connector is managed through a Super I/O chip. The DIO connector pins are
user programmable.
Figure 4-6: DIO Connector Location
Page 42
WSB-9452 PICMG 1.0 CPU Card
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
Ground
2
VCC
3
Output 3
4
Output 2
5
Output 1
6
Output 0
7
Input 3
8
Input 2
9
Input 1
10
Input 0
Table 4-10: DIOConnector Pinouts
4.2.7 DVI (Digital Visual Interface) Connector
CN Label:
DVI1
CN Type:
25-pin header
CN Location:
See Figure 4-7
CN Pinouts:
See Table 4-11
The WSB-9452DVI and WSB-9452SDVI models provide a digital visual interface for
digital display. Optional accessory IO-KIT-001 modules can be selected to connect to
external DVI devices.
Page 43
WSB-9452 PICMG 1.0 CPU Card
Figure 4-7: DVI Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
Data 2-
14
+5V Power
2
Data 2+
15
GND
3
GND
16
Hot Plug Detect
4
N/C
17
Data 0-
5
N/C
18
Data 0+
6
DDC Clock
19
GND
7
DDC Data
20
N/C
8
N/C
21
N/C
Page 44
WSB-9452 PICMG 1.0 CPU Card
9
Data 1-
22
GND
10
Data 1+
23
Clock +
11
GND
24
Clock -
12
N/C
25
GND
13
N/C
Table 4-11: DVI Connector Pinouts
4.2.8 FDD Connector
CN Label:
FDD1
CN Type:
34-pin header
CN Location:
See Figure 4-8
CN Pinouts:
See Table 4-12
The WSB-9452 is shipped with a 34-pin daisy-chain drive connector cable. This cable can
be connected to the FDD connector.
Page 45
WSB-9452 PICMG 1.0 CPU Card
Figure 4-8: FDD Connector Location
PIN
DESCRIPTION
PIN
DESCRIPTION
1
GND
2
REDUCE WRITE
3
GND
4
N/C
5
N/C
6
N/C
7
GND
8
INDEX#
9
GND
10
MOTOR ENABLE A#
11
GND
12
DRIVE SELECT B#
13
GND
14
DRIVE SELECT A#
Page 46
WSB-9452 PICMG 1.0 CPU Card
15
GND
16
MOTOR ENABLE B#
17
GND
18
DIRECTION#
19
GND
20
STEP#
21
GND
22
WRITE DATA#
23
GND
24
WRITE GATE#
25
GND
26
TRACK 0#
27
GND
28
WRITE PROTECT#
29
GND
30
READ DATA#
31
GND
32
SIDE 1 SELECT#
33
GND
34
DISK CHANGE#
Table 4-12: FDD Connector Pinouts
4.2.9 Front Panel Connector
CN Label:
F_PANEL1
CN Type:
14-pin header
CN Location:
See Figure 4-9
CN Pinouts:
See Table 4-13
The system front panel connector connects to:
the system chassis front panel LEDs
the chassis speaker
the power switch
the reset button
Page 47
WSB-9452 PICMG 1.0 CPU Card
Figure 4-9: Front Panel Connector Location
FUNCTION
Power LED
PWRBTN
HDDLED
PIN
DESCRIPTION
1
+5V
3
N/C
5
FUNCTION
DESCRIPTION
2
+5V
4
N/C
GROUND
6
N/C
7
PWRBTN+
8
Speaker
9
PWRBTN-
10
N/C
11
+5V
12
Reset-
13
HDLED-
14
GND
Speaker
RESET
Table 4-13: Front Panel Connector Location
Page 48
PIN
WSB-9452 PICMG 1.0 CPU Card
4.2.10 IDE Connectors
CN Label:
IDE1, IDE2
CN Type:
40-pin box header
CN Location:
See Figure 4-10
CN Pinouts:
See Table 4-14
One IDE connector provides connectivity for two IDE devices. WSB-9452 and
WSB-9452DVI models have one IDE connector. WSB-9452S and WSB-9452SDVI
models have two IDE connectors.
Figure 4-10: IDE Connectors Location
Page 49
WSB-9452 PICMG 1.0 CPU Card
PIN
DESCRIPTION
PIN
DESCRIPTION
1
RESET#
2
GND
3
DATA 7
4
DATA 8
5
DATA 6
6
DATA 9
7
DATA 5
8
DATA 10
9
DATA 4
10
DATA 11
11
DATA 3
12
DATA 12
13
DATA 2
14
DATA 13
15
DATA 1
16
DATA 14
17
DATA 0
18
DATA 15
19
GND
20
N/C
21
IDE DRQ
22
GND
23
IOW#
24
GND
25
IOR#
26
GND
27
IDE CHRDY
28
BALE – DEFAULT
29
IDE DACK
30
GND
31
INTERRUPT
32
N/C
33
SA1
34
PDIAG#
35
SA0
36
SA2
37
HDC CS0#
38
HDC CS1#
39
HDD ACTIVE#
40
GND
Table 4-14: IDE Connector Pinouts
4.2.11 Inverter Connector
CN Label:
INVERTER1
CN Type:
5-pin wafer connector
CN Location:
See Figure 4-11
CN Pinouts:
See Table 4-15
Page 50
WSB-9452 PICMG 1.0 CPU Card
The inverter control connector enables power on/off backlight during the power saving
mode.
Figure 4-11: Inverter Connector Location
PIN
DESCRIPTION
1
BRIGHTNESS
2
GND1
3
12V
4
GND2
5
BL_EN
Table 4-15: Inverter Connector Pinouts
Page 51
WSB-9452 PICMG 1.0 CPU Card
4.2.12 IrDA Interface Connector
CN Label:
IR1
CN Type:
5-pin header
CN Location:
See Figure 4-12
CN Pinouts:
See Table 4-16
The integrated IrDA interface connector supports both the SIR and ASKIR infrared
protocols.
Figure 4-12: IrDA Interface Connector Location
Page 52
WSB-9452 PICMG 1.0 CPU Card
PIN
DESCRIPTION
1
VCC
2
NC
3
IR-RX
4
GND
5
IR-TX
Table 4-16: IrDA Interface Connector Pinouts
4.2.13 Keyboard Connector
CN Label:
KB1
CN Type:
4-pin wafer
CN Location:
See Figure 4-13
CN Pinouts:
See Table 4-17
For alternative application, a keyboard pin header connector is also available on board.
This connector requires a special adapter cable.
Page 53
WSB-9452 PICMG 1.0 CPU Card
Figure 4-13: Keyboard Connector Location
PIN
DESCRIPTION
1
Keyboard Clock
2
Keyboard Data
3
NC
4
GND
5
VCC
Table 4-17: KB1 Connector Pinouts
Page 54
WSB-9452 PICMG 1.0 CPU Card
4.2.14 LVDS Connector
CN Label:
LVDS1
CN Type:
30-pin crimp connector
CN Location:
See Figure 4-14
CN Pinouts:
See Table 4-18
The LVDS connector allows for a 24-bit, dual-channel, low noise, low power, and low
amplitude high-speed data connection between the CPU card and LCD panel.
Figure 4-14: LVDS Connector Location
Page 55
WSB-9452 PICMG 1.0 CPU Card
PIN
DESCRIPTION
PIN
DESCRIPTION
1
GND
2
GND
3
A_Y0
4
A_Y0#
5
A_Y1
6
A_Y1#
7
A_Y2
8
A_Y2#
9
A_CK
10
A_CK#
11
A_Y3
12
A_Y3#
13
GND
14
GND
15
B_Y0
16
B_Y0#
17
B_Y1
18
B_Y1#
19
B_Y2
20
B_Y2#
21
B_CK
22
B_CK#
23
B_Y3
24
B_Y3#
25
GND
26
GND
27
VCC_LCD
28
VCC_LCD
29
VCC_LCD
30
VCC_LCD
Table 4-18: LVDS Connector Pinouts
4.2.15 Parallel Port Connector
CN Label:
LPT1
CN Type:
25-pin box header
CN Location:
See Figure 4-15
CN Pinouts:
See Table 4-19
The parallel port connector is usually connected to a printer or other parallel device with a
26-pin flat-cable connector.
Page 56
WSB-9452 PICMG 1.0 CPU Card
Figure 4-15: Parallel Port Connector Location
PIN
DESCRIPTION
PIN
DESCRIPTION
1
STROBE#
14
AUTO FORM FEED #
2
DATA0
15
ERROR#
3
DATA1
16
INITIALIZE#
4
DATA2
17
PRINTER SELECT LN#
5
DATA3
18
GND
6
DATA4
19
GND
7
DATA5
20
GND
8
DATA6
21
GND
Page 57
WSB-9452 PICMG 1.0 CPU Card
9
DATA7
22
GND
10
ACKNOWLEDGE#
23
GND
11
BUSY
24
GND
12
PAPER EMPTY
25
GND
13
PRINTER SELECT
Table 4-19: Parallel Port Connector Pinouts
4.2.16 PCI Express Mini Card Connector
CN Label:
CN1
CN Type:
52-pin PCI-E Mini Card slot
CN Location:
See Figure 4-16
CN Pinouts:
See Table 4-20
The CPU card is equipped with a PCI-E Mini Card connector to support the latest PCI-E
extension cards such as wireless LAN card or other compatible devices.
Page 58
WSB-9452 PICMG 1.0 CPU Card
Page 59
WSB-9452 PICMG 1.0 CPU Card
Figure 4-16: PCI Express Mini Card Connector Location
PIN
DESCRIPTION
PIN
DESCRIPTION
1
PCIE_WAKE#
2
VCC3
3
N/C
4
GND
5
N/C
6
1.5V
7
CLKREQ#
8
LFRAME#
9
GND
10
LAD3
11
CLK-
12
LAD2
13
CLK+
14
LAD1
15
GND
16
LAD0
17
PCIRST#
18
GND
19
LPC
20
VCC3
21
GND
22
PCIRST#
23
PERN2
24
3VDual
25
PERP2
26
GND
27
GND
28
1.5V
Page 60
WSB-9452 PICMG 1.0 CPU Card
29
GND
30
SMBCLK
31
PETN2
32
SMBDATA
33
PETP2
34
GND
35
GND
36
USBD-
37
N/C
38
USBD+
39
N/C
40
GND
41
N/C
42
N/C
43
N/C
44
RF_LINK#
45
N/C
46
BLUELED#
47
N/C
48
1.5V
49
N/C
50
GND
51
N/C
52
VCC3
Table 4-20: PCI Express Mini Card Connector Pinouts
4.2.17 RS-232 Serial Port Connectors
CN Label:
COM1, COM2
CN Type:
10-pin box header
CN Location:
See Figure 4-17
CN Pinouts:
See Table 4-21
The WSB-9452 CPU card has two internal high-speed UART connectors accessed
through a 10-pin cable connector.
Page 61
WSB-9452 PICMG 1.0 CPU Card
Figure 4-17: RS-232 Serial Port Connector Location
Page 62
WSB-9452 PICMG 1.0 CPU Card
PIN
DESCRIPTION
PIN
DESCRIPTION
1
DATA CARRIER DETECT (DCD1)
6
DATA SET READY (DSR1)
2
RECEIVE DATA (RXD1)
7
REQUEST TO SEND (RTS1)
3
TRANSMIT DATA (TXD1)
8
CLEAR TO SEND (CTS1)
4
DATA TERMINAL READY (DTR1)
9
RING INDICATOR (RI1)
5
GND (GND1)
10
N/C
Table 4-21: RS-232 Serial Port Connector Pinouts
4.2.18 SATA Drive Connectors
CN Label:
SATA1, SATA2, SATA3, SATA4
CN Type:
7-pin SATA drive connector
CN Location:
See Figure 4-18
CN Pinouts:
See Table 4-22
The SATA drive ports are connect to SATA HDDs with SATA signal cables. The SATA II
connectors provide connectivity with a maximum data transfer rate of 300 MB/s.
The SATA3 and SATA4 connectors are found only on the WSB-9452S and
WSB-9452SDVI.
Page 63
WSB-9452 PICMG 1.0 CPU Card
Figure 4-18: SATA Connectors Location
PIN
DESCRIPTION
PIN
DESCRIPTION
1
GND
5
RX-
2
TX+
6
3
TX-
7
GND
4
GND
8
N/C
RX+
Table 4-22: SATA Connectors Pinouts
Page 64
WSB-9452 PICMG 1.0 CPU Card
CAUTION:
Your SATA hard drives may come with both a 4P power connector and
a SATA power interface. Attach either the 4P connector or the included
SATA power cable to your SATA hard drives. DO NOT attach both the
power connectors to your SATA hard drives at the same time! Doing so
will cause damage.
NOTE:
1. SATA is supported by:
•
Windows® 2000 SP4
•
Windows® XP SP1
•
Windows® 2003, or later versions
2. Older OSes, such as Windows® 98SE or Me, do not support the
SATA interface.
4.2.19 Trusted Platform Module Connector
CN Label:
TPM1
CN Type:
20-pin header
CN Location:
See Figure 4-19
CN Pinouts:
See Table 4-23
The TPM connector is a trusted platform module connector used to secure the system on
bootup.
Page 65
WSB-9452 PICMG 1.0 CPU Card
Figure 4-19: TPM Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
FWHPCLK
2
GND
3
LFRAME#
4
KEY
5
PCIRST#
6
VCC
7
LAD3
8
LAD2
9
VCC3
10
LAD1
11
LAD0
12
GND
Page 66
WSB-9452 PICMG 1.0 CPU Card
13
SMBCLK
14
SMBDATA
15
3VDUAL
16
SERIRQ
17
GND
18
CLKRUN#
19
LPCPD#
20
LDRQ#
Table 4-23: TPM Connector Pinouts
4.2.20 TV Out Connector
CN Label:
TV1
CN Type:
6-pin header
CN Location:
See Figure 4-20
CN Pinouts:
See Table 4-24
The 2x3 pin TV out connector connects to a TV.
Page 67
WSB-9452 PICMG 1.0 CPU Card
Figure 4-20: TV Out Connector Location
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
GND
2
AGREEN_Y
3
GND
4
ARED_C
RCA Connector (only video signal)
5
GND
6
Table 4-24: TV Out Connector Pinouts
Page 68
ABLUE_CVBS
WSB-9452 PICMG 1.0 CPU Card
4.2.21 USB Connectors
CN Label:
USB01, USB23, USB45
CN Type:
8-pin header
CN Location:
See Figure 4-21
CN Pinouts:
See Table 4-25
Three 2x4 pin connectors provide connectivity to six USB 2.0 ports. An additional USB
port is found on the rear panel. The USB ports are used for I/O bus expansion.
Figure 4-21: USB Port Connector Location
Page 69
WSB-9452 PICMG 1.0 CPU Card
PIN
DESCRIPTION
PIN
DESCRIPTION
1
VCC
2
GND
3
DATA-
4
DATA+
5
DATA+
6
DATA-
7
GND
8
VCC
Table 4-25: USB Port Connector Pinouts
4.3 External Peripheral InterfaceConnectors
Figure 4-22 shows the WSB-9452 CPU card rear panel. The peripheral connectors on the
back panel can be connected to devices externally when the CPU card is installed in a
chassis. The peripheral connectors on the rear panel are:
1 x PS/2 keyboard connector
1 x USB connectors
2 x RJ-45 GbE connectors
1 x VGA connector
Figure 4-22: External Peripheral Interface Connector Panel
Page 70
WSB-9452 PICMG 1.0 CPU Card
4.3.1 LAN Connectors
CN Label:
LAN1 and LAN2
CN Type:
RJ-45
CN Location:
See Figure 4-22 (labeled number 2)
CN Pinouts:
See Table 4-26
The WSB-9452 is equipped with two built-in GbE Ethernet controllers. The controllers can
connect to the LAN through two RJ-45 LAN connectors. There are two LEDs on the
connector indicating the status of LAN. The pin assignments are listed in the following
table:
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1
MDIA3-
MDIA1+
MDIA1+
2
MDIA3+
MDIA2+-
MDIA2+-
3
MDIA2-
MDIA0-
MDIA0-
4
MDIA1-
MDIA0+
MDIA0+
Table 4-26: LAN Pinouts
PIN
DESCRIPTION
PIN
DESCRIPTION
1
MDIA3-
5
MDIA1+
2
MDIA3+
6
MDIA2+-
3.
MDIA2-
7
MDIA0-
4.
MDIA1-
8
MDIA0+
Table 4-27: Ethernet Connector Pinouts
Page 71
WSB-9452 PICMG 1.0 CPU Card
Figure 4-23: RJ-45 Ethernet Connector
The RJ-45 Ethernet connector has two status LEDs, one green / orange and one yellow.
The green / orange LED indicates the speed and the yellow LED indicates activity or is
linked on the port. See Table 4-27.
SPEED LED
STATUS
ACT/LINK LED
DESCRIPTION
STATUS
DESCRIPTION
GREEN
100Mbps connection
YELLOW
Linked
ORANGE
1Gbps connection
BLINKING
Data Activity
Table 4-27: RJ-45 Ethernet Connector LEDs
4.3.2 Mini-DIN 6 PS/2 Connector
CN Label:
KB_MS1
CN Type:
Mini-DIN 6 PS/2
CN Location:
See Figure 4-22 (labeled number 1)
CN Pinouts:
See Table 4-28
The WSB-9452CPU card has a mini-DIN 6 PS/2 connector on the mounting bracket for
easy connection to a PS/2 keyboard or PS/2 mouse. The card comes with a cable to
convert the mini-DIN 6 PS/2 into two mini-DIN 6 PS/2 connectors for keyboard and mouse
connection.
Page 72
WSB-9452 PICMG 1.0 CPU Card
Figure 4-24: Mini-DIN 6 PS/2 Connector
PIN NO. DESCRIPTION
1
Keyboard Data
2
Mouse Data
3
GND
4
VCC
5
Keyboard Clock
6
Mouse Clock
Table 4-28: Mini-DIN 6 PS/2 Connector
4.3.3 USB Connector
CN Label:
USB_C6
CN Type:
USB port
CN Location:
See Figure 4-22 (labeled number 3)
CN Pinouts:
See Table 4-29
The WSB-9452has a one rear panel USB port. This port connects to both USB 2.0 and
USB 1.1 devices.
Page 73
WSB-9452 PICMG 1.0 CPU Card
PIN NO. DESCRIPTION
1
VCC
2
DATA-
3
DATA+
4
GROUND
Table 4-29: USB Port Pinouts
4.3.4 VGA connector
CN Label:
VGA1
CN Type:
HD-D-sub 15 female connector
CN Location:
See Figure 4-22 (labeled number 4)
CN Pinouts:
See Table 4-30
A 15-pin VGA connector connects to standard displays.
Figure 4-25: VGA Connector
PIN NO. DESCRIPTION
PIN NO. DESCRIPTION
1
RED
2
GREEN
3
BLUE
4
NC
5
GND
6
GND
7
GND
8
GND
9
VCC
10
GND
11
NC
12
DDCDAT
Page 74
WSB-9452 PICMG 1.0 CPU Card
13
HSYNC
15
DDCCLK
14
VSYNC
Table 4-30: VGA Connector Pinouts
Page 75
WSB-9452 PICMG 1.0 CPU Card
Chapter
5
5 Installation and
Configuration
Page 76
WSB-9452 PICMG 1.0 CPU Card
5.1 Anti-static Precautions
Electrostatic discharge (ESD) can cause serious damage to electronic components,
including the WSB-9452. (Dry climates are especially susceptible to ESD.) It is therefore
critical that whenever the WSB-9452 (or any other electrical component) is handled, the
following anti-static precautions are strictly adhered to.
Wear an anti-static wrist band: Wearing a simple anti-static wrist band can
help to prevent ESD from damaging the board.
Self-grounding: Before handling the board, touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
5.2 Installation Considerations
NOTE:
The following installation notices and installation considerations should
be read and understood before the CPU card is installed. All
installation notices pertaining to the installation of the CPU card should
be strictly adhered to. Failing to adhere to these precautions may lead
to severe damage of the CPU card and injury to the person installing
the CPU card.
5.2.1 Installation Notices
Before and during the installation of the WSB-9452 CPU card, please do the following:
Read the user manual
o
The user manual provides a complete description of the WSB-9452 CPU
card, installation instructions and configuration options.
Page 77
WSB-9452 PICMG 1.0 CPU Card
Wear an electrostatic discharge cuff (ESD)
o
Electronic components are easily damaged by ESD. Wearing an ESD cuff
will remove ESD from your body and help to prevent ESD damage to the
CPU card.
Place the CPU Card on an antistatic pad
o
When you are installing or configuring the CPU Card, place it on an
antistatic pad. This will help to prevent potential ESD damage.
Turn off all power to the WSB-9452 CPU card
o
When working with the CPU card, make sure that it is disconnected from
all power supplies and that no electricity is being fed into the system.
Before and during the installation of the WSB-9452 CPU card DO NOT:
remove any of the stickers on the PCB board. These stickers are required for
warranty validation.
use the product before you have verified that all cables and power connectors
are properly connected.
allow screws to come in contact with the PCB circuit, connector pins, or its
components.
5.3 Unpacking
NOTE:
If any of the items listed below are missing when you unpack the
WSB-9452 CPU card, do not proceed with the installation and contact the
reseller or vendor you purchased the CPU card from.
5.3.1 Unpacking Precautions
Before you install the WSB-9452 CPU card, you must unpack the CPU card. Some
components on WSB-9452 are very sensitive to static electricity and can be damaged by a
sudden rush of power. To protect it from being damage, follow these precautions:
Page 78
WSB-9452 PICMG 1.0 CPU Card
Ground yourself to remove any static charge before touching your WSB-9452 .
You can do so by wearing a grounded wrist strap at all times or by frequently
touching any conducting materials that is connected to the ground.
Handle your WSB-9452 by its edges. Do not touch the IC chips, leads or
circuitry if not necessary.
Do not place a PCB on top of an anti-static bag. Only the inside of the bag is safe from
static discharge.
5.3.2 Checklist
When you unpack the WSB-9452, please make sure that your package contains the
following items.
1 x WSB-9452 single board computer
1 x Mini jumper pack
1 x ATA 66/100 flat cable
1 x Dual RS-232 cable
2 x SATA cables
1 x SATA power cable
1 x Keyboard/ PS2 mouse Y cable
1 x USB cable
1 x Utility CD
1 x QIG (quick installation guide)
If one or more of these items are missing, please contact the reseller or vendor you
purchased the WSB-9452 CPU card from and do not proceed any further with the
installation.
Page 79
WSB-9452 PICMG 1.0 CPU Card
5.4 WSB-9452 CPU Card Installation
WARNING:
Never run the CPU card without an appropriate heatsink and cooler
that can be ordered from IEI Technology or purchased separately.
Be sure to use the CPU 12V power connector (CPU12V1) for the CPU
power.
WARNING:
Please note that the installation instructions described in this manual
must be carefully followed in order to avoid damage to the CPU card
components and injury to you.
WARNING:
When installing electronic components onto the CPU card always
follow the previously outlined anti-static precautions in order to prevent
ESD damage to your board and other electronic components like the
CPU and DIMM modules
The following components must be installed onto the CPU card or connected to the CPU
card during the installation process.
CPU
CPU cooling kit
Page 80
WSB-9452 PICMG 1.0 CPU Card
DDR2 memory modules
Peripheral devices
5.4.1 Socket 478 CPU Installation
WARNING:
CPUs are expensive and sensitive components. When installing the
CPU please be careful not to damage it in anyway. Make sure the CPU
is installed properly and ensure that a heat sink and CPU cooling fan
are properly installed before the WSB-9452 board is run.
If a heat sink and cooling fan are not properly installed both the CPU
and the board may be damaged.
To install Socket 478-pin CPU onto the WSB-9452 board, follow the steps below:
WARNING:
When handling the CPU, only hold it on the sides. DO NOT touch the
pins at the bottom of the CPU.
Step 1: Is the CPU retention screw in an unlocked position? When shipped, the
retention screw of the CPU socket should be in the unlocked position. If it is not
in the unlocked position, use a screwdriver to position it in an unlocked position.
(See Figure 5-1)
Page 81
WSB-9452 PICMG 1.0 CPU Card
Figure 5-1: Make sure the CPU socket retention screw is unlocked
Step 2: Inspect the CPU socket. Make sure there are no bent pins and make sure the
socket contacts are free of foreign material. If any debris is found, remove it with
compressed air.
Step 3: Correctly position the CPU. Make sure the pin 1 mark matches the cut edge
on the CPU socket. Carefully place the CPU on top of the socket. When properly
placed, the CPU should be easily inserted into the socket.
Step 4: Insert the CPU. To insert the CPU into the socket, hold the CPU by its edges
and follow the instructions below:
Step 5: Correctly orientate the CPU with the IHS (Integrated Heat Sink) side facing
upward.
Step 6: Locate the pin 1 mark on the CPU.
Step 7: Gently insert the CPU into the socket.
Step 8: Rotate the retention screw into the locked position. (See Figure 5-2)
Page 82
WSB-9452 PICMG 1.0 CPU Card
Figure 5-2: Lock the CPU Socket Retention Screw
5.4.2 Cooling Kit (CF-479B-RS ) Installation
Figure 5-3: IEI CF-479B-RS Cooling Kit
IEI provides a cooling kit designed for socket 478 CPUs. (See Figure 5-3)
The
cooling kit is comprised of a CPU heat sink and a cooling fan.
Page 83
WSB-9452 PICMG 1.0 CPU Card
NOTE:
The CF-479B-RS heat sink comes with a sprayed layer of thermal paste.
Make sure the paste is not accidentally wiped during the unpacking or
installation of the heat sink. Thermal paste between the CPU and the heat
sink is important for optimum heat dissipation.
To install the CF-479B-RS cooling kit, please follow the steps below.
Step 1: Install the support bracket. Remove the tape from the support bracket. From
the solder side of the board, align the support bracket to the holes on board and
stick in place.
Figure 5-4: Install Support Bracket
Step 2: Properly orient the cooling kit. The CPU fan cable must not interfere with the
fan or other moving parts. Make sure the cable can be routed away from the
moving parts.
Step 3: Properly align the cooling kit. Line up the four screws with the screw holes on
the support bracket below the board (Figure 5-5).
Page 84
WSB-9452 PICMG 1.0 CPU Card
Figure 5-5: Align the Cooling Kit
Step 4: Place the cooling kit onto the CPU. Push down the fan with some pressure to
secure the cooling kit with the support bracket. See Figure 5-6.
Step 5: Tighten the screws. Use a screwdriver to tighten the four screws. In a diagonal
pattern, tighten each screw a few turns then move to the next one, until they are
all secured. Do not overtighten the screws. See Figure 5-6.
Step 6: Connect the fan cable. Connect the cooling kit fan cable to the fan connector
on the board. Carefully route the cable away from heat generating chips and fan
blades. Step 0:
Page 85
WSB-9452 PICMG 1.0 CPU Card
Figure 5-6: Secure the Cooling Kit
5.4.3 DIMM Module Installation
5.4.3.1 Purchasing the Memory Module
WARNING:
When purchasing the DIMM modules, make sure the modules are
compatible with the DIMM slot specified in Section 2.6 Memory
Support.
Page 86
WSB-9452 PICMG 1.0 CPU Card
WARNING:
The board supports DDR2 DIMM modules only. DDR1 and DDR2 are
not compatible. If a DDR1 DIMM module is installed, the system may
be damaged and become inaccessible. Please only use DDR2 DIMM
modules.
When you purchase your DIMM modules, the following considerations should be taken
into account:
Each DIMM socket can support DIMM modules with a maximum size of 2GB
Only use DDR2 memory chips in the DIMM slots
It is recommended that you use memory modules of identical brand, size,
chips, and speed.
DIMMs must use the same density memory chips
Both DIMMs must use the same DRAM bus width
Both DIMMs must be either single-sided or dual-sided
5.4.3.2 DIMM Module Installation
The WSB-9452 CPU card has two 240-pin DDR2 SDRAM DIMM sockets. To install the
DIMM modules, follow the instructions below.
Step 1: Make sure the two handles of the DIMM socket are in the "open" position,
leaning outward (Figure 5-7).
Page 87
WSB-9452 PICMG 1.0 CPU Card
Figure 5-7: Installing the DIMM Module
Page 88
WSB-9452 PICMG 1.0 CPU Card
Step 2: Slowly slide the DIMM module along the plastic guides on both ends of the
socket. Press the DIMM module down into the socket until it clicks into position
and the two handles have automatically locked the memory module into place.
Step 3: To remove the memory module, push both handles outward, and the memory
module is ejected by the mechanism in the socket. Step 0:
5.4.4 Peripheral Device Connection
Cables provided by IEI that connect peripheral devices to the CPU Card are listed in
Table 5-1. Cables not included in the kit must be separately purchased.
Quantity
Type
1
ATA 66/100 flat cable
2
SATA cables
1
SATA power cable
1
Keyboard/ PS2 mouse Y cable
1
RS-232 cable
1
USB cable
Table 5-1: IEI Provided Cables
Page 89
WSB-9452 PICMG 1.0 CPU Card
5.4.4.1 IDE Disk Drive Connectors (IDE1, IDE2)
The cable used to connect the motherboard to the IDE device is a standard 40-pin
ATA/100 flat cable. To connect an IDE device to the motherboard, follow the instructions
below.
Step 1: Find the IDE flat cable in the kit that came with the motherboard.
Step 2: Connect one end of the cable to the IDE connector on the motherboard. A keyed
pin on the IDE connector prevents it from being connected incorrectly.
Step 3: Locate the red wire on the other side of the cable that corresponds to the pin 1
connector.
Step 4: Connect the other side of the cable to the IDE device making sure that the pin 1
cable corresponds to pin 1 on the connector.Step 0:
Page 90
WSB-9452 PICMG 1.0 CPU Card
Figure 5-8: Connection of IDE Connector
NOTE:
When two IDE disk drives are connected together, back-end jumpers
on the drives must be used to configure one drive as a master and the
other as a slave.
Page 91
WSB-9452 PICMG 1.0 CPU Card
5.4.4.2 Floppy Drive Connector (FDD1)
This connector provides access to an externally mounted 3.5” floppy drive. To connect the
CPU Card to a FDD, follow the instructions below.
Step 1: Insert one side of the cable into the FDC making sure that the red wire on the
cable corresponds to pin 1 on the connector.
Step 2: Attach the connector on the other side of the cable to the floppy drive(s). You
can only use one connector in the set. The connection sequence determines
which of the two connected floppy drives is drive A: and which is drive B.
Step 0:
5.4.5 SATA Drive Connection
The CPU card has on-board SATA drive connectors. Refer to Table 1-1 for model
variations supporting two or four SATA II connectors. To connect the SATA drives to the
connectors, follow the steps below.
Step 1: Locate the SATA drive connector on the board.
Step 2: Press the clip on the connector at the end of the SATA cable and insert the
cable connector into the on-board SATA drive connector (Figure 5-9).
Page 92
WSB-9452 PICMG 1.0 CPU Card
Figure 5-9: SATA Drive Cable Connection
Step 3: Connect the connector on the other end of the cable to the connector at the back
of the SATA drive (Figure 5-10).
Step 4: Connect the SATA power connector to the back of the SATA drive (Figure
5-10).
Page 93
WSB-9452 PICMG 1.0 CPU Card
Figure 5-10: SATA Drive Connection
5.4.6 Installing the RS-232 Cable
A dual RS-232 cable consisting of two cables attached to two D-sub 9 male connectors
that are mounted onto a bracket can be connected to the COM1 and COM2 RS-232
connectors. To install an RS-232 cable, follow the steps below.
Step 1: Locate the two RS-232 serial port connectors.
Step 2: Insert the two small connectors on the cables into the serial port box headers on
the CPU card (Figure 5-11).
Page 94
WSB-9452 PICMG 1.0 CPU Card
Figure 5-11: Dual RS-232 Cable Installation
Step 3: Secure the bracket supporting the two D-sub 9 male connectors to the chassis.
To do this, refer to the chassis manual. Step 0:
5.4.7 USB 2.0 Cable Connection
The CPU card is shipped with a dual USB cable. The dual USB cable consists of two
connectors attached to two independent cables. Each cable is then attached to a USB port
connector that is mounted on a bracket. To install the USB cable, follow the steps below.
Step 1: Install a USB module supporting two USB ports to the chassis. Secure the USB
module bracket following the instructions in the documentation that came with
the USB module and the chassis.
Page 95
WSB-9452 PICMG 1.0 CPU Card
Step 2: Insert the two 4-pin connectors from the module into the USB pin headers on the
CPU card. (Figure 5-12)
Figure 5-12: USB Cable Installation
Page 96
WSB-9452 PICMG 1.0 CPU Card
5.5 On-board Jumpers
NOTE:
A jumper is a metal bridge that is
used to close an electrical circuit. It
consists of two metal pins and a
small metal clip (often protected by a
plastic cover) that slides over the pins
to connect them. To
CLOSE/SHORT a jumper means
connecting the pins of the jumper
with the plastic clip and to OPEN a
jumper means removing the plastic
Figure 5-13 Jumper
clip from a jumper.
The CPU card two on-board jumpers. The jumpers are described in Table 5-2.
Label
Connector
Type
J_CMOS1
CMOS state setting
3-pin header
J_LVDS1
L CD Voltage select
3-pin header
JAUTO1
AT/ATX mode select
2-pin header
JLAN_PWR1
LAN power select
6-pin header
Table 5-2: On-board Jumpers
5.5.1 AT Power Select Jumper Settings
Jumper Label:
JAUTO1
Jumper Type:
2-pin header
Jumper Settings:
See Table 5-3
Jumper Location:
See Figure 5-14
Page 97
WSB-9452 PICMG 1.0 CPU Card
The AT Power Select jumper specifies the systems power mode as AT or ATX. AT Power
Select jumper settings are shown in Table 5-3.
AT Power Select
Description
Short
Use AT power
Open
Use ATX power
Default
Table 5-3: AT Power Select Jumper Settings
The location of the AT Power Select jumper is shown in Figure 5-14 below.
Figure 5-14: AT Power Select Jumper Location
5.5.2 Clear CMOS Jumper
Page 98
WSB-9452 PICMG 1.0 CPU Card
Jumper Label:
J_CMOS1
Jumper Type:
3-pin header
Jumper Settings:
See Table 5-4
Jumper Location:
See Figure 5-15
If the CPU card fails to boot due to improper BIOS settings, use this jumper to clear the
CMOS data and reset the system BIOS information. To do this, use the jumper cap to
close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.
If the “CMOS Settings Wrong” message is displayed during the boot up process, the fault
may be corrected by pressing the F1 to enter the CMOS Setup menu. Do one of the
following:
Enter the correct CMOS setting
Load Optimal Defaults
Load Failsafe Defaults.
After having done one of the above, save the changes and exit the CMOS Setup menu.
J_CMOS1
DESCRIPTION
Short 1-2 (Default)
Normal Operation
Short 2-3
Clear CMOS Setup
Table 5-4: Clear CMOS Jumper Settings
The location of the clear CMOS jumper is shown in Figure 5-15 below.
Page 99
WSB-9452 PICMG 1.0 CPU Card
Figure 5-15: Clear CMOS Jumper
5.5.3 LVDS LCD Voltage Selection
WARNING:
Making the wrong setting on this jumper may cause irreparable
damage to both the motherboard and the LCD screen connected to the
on-board connector.
Page 100
WSB-9452 PICMG 1.0 CPU Card
Jumper Label:
J_LVDS1
Jumper Type:
3-pin header
Jumper Settings:
See Table 5-5
Jumper Location:
See Figure 5-16
This jumper allows the user to set the voltage for the LCD panel. Before setting this jumper
please refer to the LCD panel user guide to determine the required voltage. After the
required voltage is known, make the necessary jumper setting in accordance with the
settings shown in Table 5-5.
J_LVDS1
Short 1-2
Short 2-3
(Default)
DESCRIPTION
Set The Voltage Level of Panel to VCC3
Set The Voltage Level of Panel to VCC
Table 5-5: LVDS LCD Voltage Selection Jumper Settings
The LVDS Voltage Selection jumper location. is shown in Figure 5-16.
Page 101
WSB-9452 PICMG 1.0 CPU Card
Figure 5-16: LVDS Voltage Selection Jumper Pinout Locations
5.5.4 LAN Power Selection
Jumper Label:
JLAN_PWR1
Jumper Type:
6-pin header
Jumper Settings:
See Table 5-6
Jumper Location:
See Figure 5-17
The LAN Power Selection jumper allows the LAN (LAN1 and LAN2) power to be set. The
LAN Power Selection jumper settings are shown in Table 5-6.
Page 102
WSB-9452 PICMG 1.0 CPU Card
LAN Power Select
Description
Short 1-3
LAN1 uses 3.3V_Dual
Short 3-5
LAN1 uses 3.3V
Short 2-4
LAN2 uses 3.3V_Dual
Short 4-6
LAN2 uses 3.3V
Table 5-6: LCD Voltage Selection Jumper Settings
The LAN Power Selection jumper location is shown in Figure 5-17.
Figure 5-17: LAN Power Selection Jumper Location
Page 103
WSB-9452 PICMG 1.0 CPU Card
5.6 Chassis Installation
After the CPU, the cooling kit, and the DIMM modules have been installed and after the
internal peripheral connectors have been connected to the peripheral devices and the
jumpers have been configure, the CPU Card can be mounted into a chassis.
To mount the CPU Card into a chassis please refer to the chassis user guide that came
with the product.
5.7 Rear Panel Connectors
5.7.1 Keyboard and Mouse Connection
A PS/2 keyboard and a PS/2 mouse can be connected to the appropriate PS/2 connector
on the rear panel.
5.7.2 VGA Port Installation
The conventional CRT monitor connector is a 15-pin, female D-SUB connector. Pin
assignments can be seen in that can be connected to external monitors.
5.7.3 Ethernet Connection
The rear panel RJ-45 connectors can be connected to an external LAN and communicate
with data transfer rates up to 1Gb/s.
5.7.4 USB Connection
The rear panel USB connector provides easier and quicker access to external USB
devices. The rear panel USB connector is a standard connector and can easily be
connected to other USB devices.
Page 104
WSB-9452 PICMG 1.0 CPU Card
Chapter
6
6 AMI BIOS Setup
Page 105
WSB-9452 PICMG 1.0 CPU Card
6.1 Introduction
A licensed copy of AMI BIOS is preprogrammed into the ROM BIOS. The BIOS setup
program allows users to modify the basic system configuration. This chapter describes
how to access the BIOS setup program and the configuration options that may be
changed.
6.1.1 Starting Setup
The AMI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the DELETE key as soon as the system is turned on or
2. Press the DELETE key when the “Press Del to enter SETUP” message
appears on the screen. 0.
If the message disappears before, restart the computer and try again.
6.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the “+” and “-“ keys to
change entries, press F1 for help and press ESC to quit. Navigation keys are shown in.
Key
Function
Up arrow
Move to previous item
Down arrow
Move to next item
Left arrow
Move to the item on the left hand side
Right arrow
Move to the item on the right hand side
Esc key
Main Menu – Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
“+” key
Increase the numeric value or make changes
“-“ key
Decrease the numeric value or make changes
F1 key
General help, only for Status Page Setup Menu and Option
Page Setup Menu
Page 106
WSB-9452 PICMG 1.0 CPU Card
F2 /F3 key
Change color from total 16 colors. F2 to select color
forward.
F10 key
Save all the CMOS changes, only for Main Menu
Table 6-1: BIOS Navigation Keys
6.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press ESC or
the F1 key again.
6.1.4 Unable to Reboot after Configuration Changes
If the computer cannot boot after changes to the system configuration is made, CMOS
defaults. Use the jumper described in Chapter 4, Section 5.5.1.
6.1.5 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:
Main Changes the basic system configuration.
Advanced Changes the advanced system settings.
PCIPnP Changes the advanced PCI/PnP Settings
Boot Changes the system boot configuration.
Security Sets User and Supervisor Passwords.
Chipset Changes the chipset settings.
Exit Selects exit options and loads default settings
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
Page 107
WSB-9452 PICMG 1.0 CPU Card
6.2 Main
When the BIOS Setup program is entered, the Main menu (BIOS Menu 1) appears. The
Main menu gives an overview of the basic system information.
BIOS Menu 1: Main
System Overview
The System Overview lists a brief summary of different system components. The fields in
System Overview cannot be changed. The items shown in the system overview include:
AMI BIOS: Displays auto-detected BIOS information
o
o
o
Page 108
Version:
Current BIOS version
Build Date: Date the current BIOS version was made
ID:
Installed BIOS ID
WSB-9452 PICMG 1.0 CPU Card
Processor: Displays auto-detected CPU specifications
o
o
o
Type: Names the currently installed processor
Speed: Lists the processor speed
Count: The number of CPUs on the motherboard
System Memory: Displays the auto-detected system memory.
o
Size:
Lists memory size
The System Overview field also has two user configurable fields:
System Time [xx:xx:xx]: The system time is set here.
System Date [Day xx/xx/xxxx]: The system date is set here.
6.3 Advanced
The Advanced menu (BIOS Menu 2) allows access to the CPU and peripheral device
configuration options through the following sub-menus:
WARNING:
Setting the wrong values in the sections below may cause the system
to malfunction. Make sure that the settings made are compatible with
the hardware.
CPU Configuration (see Section 6.3.1)
IDE Configuration (see Section 6.3.2)
Floppy Configuration (see Section 6.3.3)
SuperIO Configuration (see Section 6.3.4)
Hardware Health Configuration (see Section 6.3.5)
ACPI Configuration (see Section 6.3.6)
APM Configuration (see Section 6.3.7)
MPS Configuration (see Section 6.3.8)
Remote Access Configuration (see Section 6.3.9)
Trusted Computing (see Section 6.3.10)
USB Configuration (see Section 6.3.11)
Page 109
WSB-9452 PICMG 1.0 CPU Card
BIOS Menu 2: Advanced
Page 110
WSB-9452 PICMG 1.0 CPU Card
6.3.1 CPU Configuration
The CPU Configuration menu (BIOS Menu 3) shows detailed CPU specifications and
CPU configuration options.
BIOS Menu 3: CPU Configuration
The CPU Configuration menu (BIOS Menu 3) lists the following CPU details:
Manufacturer: Lists the name of the CPU manufacturer
Brand String: Lists the brand name of the CPU being used
Frequency: Lists the CPU processing speed
FSB Speed: Lists the FSB speed
Cache L1: Lists the CPU L1 cache size
Cache L2: Lists the CPU L2 cache size
Page 111
WSB-9452 PICMG 1.0 CPU Card
The following CPU Configuration menu item can be configured.
Intel(R) SpeedStep(tm) tech. [Automatic]
Use the Intel(R) SpeedStep(tm) tech. option to enable or disable the Enhanced Intel®
SpeedStep® Technology (EIST) feature, which allows power settings adjustment in the
operating system.
EIST feature is disabled; the system runs at
Disabled
the default CPU speed
Automatic
DEFAULT
The operating system controls the CPU
speed.
Maximum Speed
CPU speed is set to maximum
Minimum Speed
CPU speed is set to minimum
6.3.2 IDE Configuration
The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the
IDE devices installed in the system.
Page 112
WSB-9452 PICMG 1.0 CPU Card
BIOS Menu 4: IDE Configuration
ATA/IDE Configuration [Compatible]
The ATA/IDE Configuration BIOS option allows the user to configure the ATA/IDE device
mode.
Page 113
WSB-9452 PICMG 1.0 CPU Card
Disable all ATA/IDE ports. No Primary/Secondary IDE
Disabled
mode is presented for configuration
Compatible
DEFAULT
Up to 4 HDDs can be used, two for SATA and the other
for PATA IDE. If this option is selected, “Legacy IDE
Channels” option is presented for configuration.
If this option is selected, “Configure SATA as” and
Enhanced
“Configure SATA channels” options are presented for
configuration.
Legacy IDE Channels [SATA Pri, PATA Sec]
Use the Legacy IDE Channels option configures PATA and SATA resources for
operating systems that require legacy IDE operation.
SATA Only
Enable up to two SATA devices
Reserved
The legacy IDE channels are reserved
SATA
Pri,
DEFAULT
This option allows the system to access the SATA
PATA Sec
devices before the primary IDE devices
PATA Only
Enable the two primary IDE devices. Select this option
only when the two primary IDE devices are available
IDE Master and IDE Slave
When entering setup, BIOS auto detects the presence of IDE devices. This displays the
status of the auto detected IDE devices. The following IDE devices are detected and are
shown in the IDE Configuration menu:
Primary IDE Master
Primary IDE Slave
Page 114
WSB-9452 PICMG 1.0 CPU Card
Secondary IDE Master
Secondary IDE Slave
The IDE Configuration menu (BIOS Menu 4) allows changes to the configurations for the
IDE devices installed in the system. If an IDE device is detected, and one of the above
listed four BIOS configuration options are selected, the IDE configuration options shown in
Section 6.3.2.1 appear.
6.3.2.1 IDE Master, IDE Slave
IDE Master and IDE Slave configuration options for both primary and secondary IDE
devices are shown in the BIOS menu below.
BIOS Menu 5: IDE Master and IDE Slave Configuration
Type [Auto]
The Type BIOS option determines the type of device that the AMIBIOS attempts to boot
from after the Power-On Self-Test (POST) has completed.
Page 115
WSB-9452 PICMG 1.0 CPU Card
Selecting this value prevents the BIOS from searching
Not Installed
for an IDE disk drive on the specified channel.
Auto
DEFAULT
This selection enables the BIOS to auto detect the
IDE disk drive type attached to the specified channel.
This setting should be used if an IDE hard disk drive is
attached to the specified channel.
The CD/DVD option specifies that an IDE CD-ROM
CD/DVD
drive is attached to the specified IDE channel. The
BIOS does not attempt to search for other types of
IDE disk drives on the specified channel.
This option specifies an ATAPI Removable Media
ARMD
Device. These include, but are not limited to:
ZIP
LS-120
LBA/Large Mode [Auto]
The LBA/Large Mode BIOS option disables or auto detects LBA (Logical Block
Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the
maximum drive capacity is 137 GB.
This selection prevents the BIOS from using the LBA
Disabled
mode control on the specified channel.
Auto
DEFAULT
This option allows the BIOS to auto detect the LBA mode
control on the specified channel.
Page 116
WSB-9452 PICMG 1.0 CPU Card
Block (Multi Sector Transfer) [Auto]
Selecting this option prevents the BIOS from using
Disabled
Multi-Sector Transfer on the specified channel. The data
to and from the device occurs one sector at a time.
DEFAULT
Auto
Selecting this value to allows the BIOS to auto detect the
device support for Multi-Sector Transfers on the specified
channel. If supported. Select this value to allow the BIOS
to auto detect the number of sectors per block for transfer
from the hard disk drive to the memory. The data transfer
to and from the device occurs multiple sectors at a time.
PIO Mode [Auto]
The PIO Mode option selects the IDE PIO (Programmable I/O) mode program timing
cycles between the IDE drive and the programmable IDE controller. As the PIO mode
increases, the cycle time decreases.
Auto
DEFAULT
This setting allows the BIOS to auto detect the PIO mode. Use
this value if the IDE disk drive support cannot be determined.
0
PIO mode 0 selected with a maximum transfer rate of 3.3MBps
1
PIO mode 1 selected with a maximum transfer rate of 5.2MBps
2
PIO mode 2 selected with a maximum transfer rate of 8.3MBps
3
PIO mode 3 selected with a maximum transfer rate of 11.1MBps
4
PIO mode 4 selected with a maximum transfer rate of 16.6MBps
(This setting generally works with all hard disk drives
manufactured after 1999. For other disk drives, such as IDE
CD-ROM drives, check the specifications of the drive.)
Page 117
WSB-9452 PICMG 1.0 CPU Card
DMA Mode [Auto]
The DMA Mode BIOS selection adjusts the DMA mode options.
Auto
DEFAULT
The BIOS auto detects the DMA mode. Use this value if the
IDE disk drive support cannot be determined.
S.M.A.R.T [Auto]
The Self-Monitoring Analysis and Reporting Technology (SMART) feature can help predict
impending drive failures. The S.M.A.R.T BIOS option enables or disables this function.
Auto
DEFAULT
BIOS to auto detects if the hard disk drive supports
S.M.A.R.T. Use this setting if the IDE disk drive support
cannot be determined.
Select this value to prevent the BIOS from using the
Disabled
SMART feature.
Select this value to allow the BIOS to use the SMART
Enabled
feature on support hard disk drives.
32Bit Data Transfer [Enabled]
The 32Bit Data Transfer BIOS option enables or disables 32-bit data transfers.
Prevents the BIOS from using 32-bit data transfers.
Disabled
Enabled
DEFAULT
Allows BIOS to use 32-bit data transfers on support hard
disk drives.
Page 118
WSB-9452 PICMG 1.0 CPU Card
6.3.3 Floppy Configuration
Use the Floppy Configuration menu (BIOS Menu 6) to set or change the configurations
for floppy disk drives.
BIOS Menu 6: Floppy Configuration
Floppy A/B [1.44 MB 3½”]
The Floppy A/B configuration option determines the types of the floppy drive installed in
the system. The following configuration options are available.
Page 119
WSB-9452 PICMG 1.0 CPU Card
Disabled
360 KB 5¼”
1.2 MB 5¼”
720 KB 3 ½”
1.44 MB 3½”
2.88 MB 3½”
6.3.4 Super IO Configuration
The Super IO Configuration menu (BIOS Menu 7) sets or changes the configurations for
the FDD controllers, parallel ports and serial ports.
BIOS Menu 7: Super IO Configuration
Page 120
WSB-9452 PICMG 1.0 CPU Card
On-board Floppy Controller [Enabled]
Use the On-board Floppy Controller to enable or disable the floppy controller. If a floppy
disk is not being used in the system, disabling this option frees up system resources that
can be redirected elsewhere in the system.
Allows BIOS to disable the floppy controller
Disabled
Enabled
DEFAULT
Allows BIOS to enable the floppy controller
Floppy Drive Swap [Disabled]
Use the Floppy Drive Swap option to designate drive A as drive B and drive B as drive A.
Disabled
DEFAULT
Cannot designate A or B to a floppy drive without
changing the physical connection
Can designate A or B to a floppy drive without changing
Enabled
the physical connection
Serial Port1 Address [3F8/IRQ4]
The Serial Port1 Address option allows BIOS to select the Serial Port 1 base address.
No base address is assigned to Serial Port 1
Disabled
3F8/IRQ4
DEFAULT
Serial Port 1 I/O port address is 3F8 and the interrupt
address is IRQ4
3E8/IRQ4
Serial Port 1 I/O port address is 3E8 and the interrupt
address is IRQ4
2E8/IRQ3
Serial Port 1 I/O port address is 2E8 and the interrupt
address is IRQ3
Page 121
WSB-9452 PICMG 1.0 CPU Card
Serial Port1 Mode [Normal]
Allows BIOS to select the mode for Serial Port 1.
Normal
DEFAULT
Serial Port 1 mode is normal
Serial Port 1 mode is ASK IR
ASK IR
Serial Port2 Address [2F8/IRQ3]
The Serial Port2 Address option allows BIOS to select the Serial Port 2 base address.
No base address is assigned to Serial Port 2
Disabled
2F8/IRQ3
DEFAULT
Serial Port 2 I/O port address is 3F8 and the interrupt
address is IRQ3
Serial Port 2 I/O port address is 3E8 and the interrupt
3E8/IRQ4
address is IRQ4
Serial Port 2 I/O port address is 2E8 and the interrupt
2E8/IRQ3
address is IRQ3
Serial Port2 Mode [Normal]
Allows BIOS to select the mode for Serial Port 2.
Normal
Page 122
DEFAULT
Serial Port 2 mode is normal
IrDA
Serial Port 2 mode is IrDA
ASK IR
Serial Port 2 mode is ASK IR
WSB-9452 PICMG 1.0 CPU Card
Parallel Port Address [Disabled]
Use the Parallel Port Address option to select the parallel port base address.
Disabled
DEFAULT
No base address is assigned to the Parallel Port
378
Parallel Port I/O port address is 378
278
Parallel Port I/O port address is 278
3BC
Parallel Port I/O port address is 3BC
Parallel Port Mode [Normal]
Use the Parallel Port Mode option to select the mode the parallel port operates in.
Normal
DEFAULT
The normal parallel port mode is the standard mode
for parallel port operation.
EPP
The parallel port operates in the enhanced parallel
port mode (EPP). The EPP mode supports
bi-directional communication between the system
and the parallel port device and the transmission
rates between the two are much faster than the
Normal mode.
ECP
The
parallel
port
operates
in
the
extended
capabilities port (ECP) mode. The ECP mode
supports bi-directional communication between the
system and the parallel port device and the
transmission rates between the two are much faster
than the Normal mode
ECP+EPP
The parallel port operates in ECP and EPP modes.
Page 123
WSB-9452 PICMG 1.0 CPU Card
Parallel Port IRQ [IRQ7]
Use the Parallel Port IRQ selection to set the parallel port interrupt address.
IRQ5 is assigned as the parallel port interrupt address
IRQ5
IRQ7
DEFAULT
IRQ7 is assigned as the parallel port interrupt address
6.3.5 Hardware Health Configuration
The Hardware Health Configuration menu (BIOS Menu 8) shows the operating
temperature, fan speeds and system voltages.
BIOS Menu 8: Hardware Health Configuration
Page 124
WSB-9452 PICMG 1.0 CPU Card
CPU FAN Mode Setting: [Full On mode]
The CPU FAN Mode Setting has the following options:
Full On mode
DEFAULT
If selected, there are no additional configurable
options.
Automatic
If selected, the following options will appear with
Mode
values that can be configured:
CPU Temp. Limit of OFF
CPU Temp. Limit of Start
CPU Temp. Limit of Full
CPU Fan Start PWM
Slope PWM 1: 0 PWM, 1 PWM
(Default), 2 PWM, 4 PWM, 8 PWM, 16
PWM, 32 PWM or 64 PWM
PWM Manually
If selected, the following option will appear with
mode
values that can be configured:
CPU Fan PWM Control
The following system parameters and values are shown. The system parameters that are
monitored are:
System Temperatures: The following system temperatures are monitored
o
o
o
CPU Temperature
System Temperature
PWM Temperature
Fan Speeds: The CPU cooling fan speed is monitored.
o
System Fan Speed
Voltages: The following system voltages are monitored
Page 125
WSB-9452 PICMG 1.0 CPU Card
o
o
o
o
o
o
o
o
o
Page 126
CPU Core
+1.8V
+3.30V
+5.00V
+12.0V
0.9V
1.5V
5VSB
VBAT
WSB-9452 PICMG 1.0 CPU Card
6.3.6 ACPI Configuration
The ACPI Configuration menu (BIOS Menu 9) configures the Advanced Configuration
and Power Interface (ACPI) and Power Management (APM) options.
BIOS Menu 9: ACPI Configuration
ACPI Aware O/S [Yes]
Use the ACPI Aware O/S option to enable the system to configure ACPI power saving
options. ACPI can only be implemented if the system OS complies with the ACPI standard.
Windows 98, Windows 2000, and Windows XP all comply with ACPI.
Page 127
WSB-9452 PICMG 1.0 CPU Card
Disables the ACPI support for the OS. This selection should
No
be disabled if the OS does not support ACPI
Yes
DEFAULT
Enables the ACPI support for the operating system. This
selection should be enabled if the OS does support ACPI
6.3.6.1 General ACPI Configuration
Use the General ACPI Configuration menu (BIOS Menu 10) to select the ACPI state
when the system is suspended.
BIOS Menu 10: General ACPI Configuration
Page 128
WSB-9452 PICMG 1.0 CPU Card
Suspend mode [Auto]
Use the Suspend Mode option to specify the sleep state the system enters when it is not
being used.
The OS selects the sleep state when then system is not
Auto
being used.
The system enters S1(POS) sleep state. The system
S1 (POS)
appears off. The CPU is stopped; RAM is refreshed; the
system is running in a low power mode.
S3 (STR)
DEFAULT
The system enters a S3(STR) sleep state. The CPU has
no power; RAM is in slow refresh; the power supply is in a
reduced power mode.
Repost Video on S3 Resume [Yes]
Use the Repost Video on S3 Resume option to enable video repost support, allowing the
video BIOS to be initialized when coming out of S3 state.
Yes
DEFAULT
The video BIOS will be initialized when coming out of S3
state
No
The video BIOS will be initialized when coming out of S3
state
Page 129
WSB-9452 PICMG 1.0 CPU Card
6.3.7 APM Configuration
Use the APM Configuration menu (BIOS Menu 11) to select the advanced power
management.
BIOS Menu 11: APM Configuration
Power Management/APM [Enabled]
The Power Management/APM BIOS option accesses the advanced power management
features.
Page 130
WSB-9452 PICMG 1.0 CPU Card
Disables the Advanced Power Management (APM)
Disabled
feature
Enabled
DEFAULT
Enables the APM feature
Restore on AC Power Loss by IO [Last State]
The Restore on AC Power Loss by IO BIOS option specifies what state the system
returns to if there is a sudden loss of power to the system.
Last State
The system returns to its previous state. If it was on, it
DEFAULT
turns itself on. If it was off, it remains off.
Power Off
The system remains turned off
Power On
The system turns on
Power Button Mode [On/Off]
The Power Button Mode BIOS specifies how the power button functions.
On/Off
DEFAULT
When the power button is pressed the system is either
turned on or off
Suspend
When the power button is pressed the system goes into
suspend mode
Resume on Ring [Disabled]
The Resume on Ring BIOS option specifies if the system will be roused from a
suspended or standby state when there is activity on the RI (ring in) modem line. That is,
the system will be roused by an incoming call on a modem.
Page 131
WSB-9452 PICMG 1.0 CPU Card
Disabled
DEFAULT
Wake event not generated by an incoming call
Wake event generated by an incoming call
Enabled
Resume on PME# [Disabled]
The Resume on PME# BIOS option specifies if the system will be roused from a
suspended or standby state when there is activity on the PCI PME (power management
event) controller.
Disabled
DEFAULT
Wake event not generated by PCI PME controller
activity
Wake event generated by PCI PME controller activity
Enabled
Resume On RTC Alarm [Disabled]
The Resume On RTC Alarm determines when the computer will be roused from a
suspended state.
Disabled
DEFAULT
The real time clock (RTC) cannot generate a wake
event
Enabled
If selected, the following will appear with values that
can be selected:
RTC Alarm Date (Days)
RTC Alarm Time
After setting the alarm, the computer will turn itself on
from a suspend state when the alarm goes off.
Page 132
WSB-9452 PICMG 1.0 CPU Card
6.3.8 MPS Configuration
Use the MPS Configuration menu (BIOS Menu 12) to select the multi-processor table.
BIOS Menu 12: MPS Configuration
MPS Revision [1.4]
Use the Multiprocessor Specification (MPS) Revision option to specify the MPS
version to be used.
MPS version 1.1 is used
1.1
1.4
DEFAULT
MPS version 1.4 is used
Page 133
WSB-9452 PICMG 1.0 CPU Card
6.3.9 Remote Access Configuration
Use the Remote Access Configuration menu (BIOS Menu 13) to configure remote
access parameters. The Remote Access Configuration is an AMIBIOS feature and
allows a remote host running a terminal program to display and configure the BIOS
settings.
BIOS Menu 13: Remote Access Configuration
Remote Access [Disabled]
Use the Remote Access option to enable or disable access to the remote functionalities
of the system.
Page 134
WSB-9452 PICMG 1.0 CPU Card
Disabled
DEFAULT
Remote access is disabled.
Remote access configuration options shown below
Enabled
appear:
Serial Port Number
Serial Port Mode
Flow Control
Redirection after BIOS POST
Terminal Type
VT-UTF8 Combo Key Support
Sredir Memory Display Delay
These configuration options are discussed below.
Serial Port Number [COM1]
Use the Serial Port Number option allows selection of the serial port used for remote
access.
COM1
COM2
DEFAULT
System is remotely accessed through COM1
System is remotely accessed through COM2
Page 135
WSB-9452 PICMG 1.0 CPU Card
NOTE:
Make sure the selected COM port is enabled through the Super I/O
configuration menu.
Base Address, IRQ [2F8h,3]
The Base Address, IRQ option cannot be configured and only shows the interrupt
address of the serial port listed above.
Serial Port Mode [115200 8,n,1]
Use the Serial Port Mode option to select baud rate through which the console redirection
is made. The following configuration options are available
115200 8,n,1
DEFAULT
57600 8,n,1
38400 8,n,1
19200 8,n,1
09600 8,n,1
NOTE:
Identical baud rate setting must be set on the host (a management
computer running a terminal software) and the slave
Flow Control [None]
Use the Flow Control option to report the flow control method for the console redirection
application.
Page 136
WSB-9452 PICMG 1.0 CPU Card
None
DEFAULT
No control flow,
Hardware
Hardware is set as the console redirection
Software
Software is set as the console redirection
Redirection After BIOS POST [Always]
Use the Redirection After BIOS POST option to specify when console redirection should
occur.
Disabled
The console is not redirected after POST
Boot Loader
Redirection is active during POST and during Boot
Loader
Always
DEFAULT
Redirection is always active (Some OSes may not
work if set to Always)
Terminal Type [ANSI]
Use the Terminal Type BIOS option to specify the remote terminal type.
ANSI
DEFAULT
The target terminal type is ANSI
VT100
The target terminal type is VT100
VT-UTF8
The target terminal type is VT-UTF8
VT-UTF8 Combo Key Support [Disabled]
Use the VT-UFT8 Combo Key Support option to enable additional keys that are not
provided by VT100 for the PC 101 keyboard.
The VT100 Terminal Definition is the standard convention used to configure and conduct
emergency management tasks with UNIX-based servers. VT100 does not support all keys
on the standard PC 101-key layout, however. The VT-UTF8 convention makes available
additional keys that are not provided by VT100 for the PC 101 keyboard.
Page 137
WSB-9452 PICMG 1.0 CPU Card
Disabled
DEFAULT
Enabled
Disables the VT-UTF8 terminal keys
Enables the VT-UTF8 combination key. Support for
ANSI/VT100 terminals
Sredir Memory Display Delay [Disabled]
Use the Sredir Memory Display Delay option to select the delay before memory
information is displayed. Configuration options are listed below
No Delay
Delay 1 sec
Delay 2 sec
Delay 4 sec
Page 138
DEFAULT
WSB-9452 PICMG 1.0 CPU Card
6.3.10 Trusted Computing
Use the Trusted Computing menu (BIOS Menu 15) to configure the trusted computing
platform settings.
BIOS Menu 14: Trusted Computing Configuration
TCG/TPM Support [No]
Use the TCG/TPM Support option to enable support for the Trusted Computing
Group/Trusted Platform Module (TCG/TPM 1.1/1.2) specification.
Enables TCG/TPM support
Yes
No
DEFAULT
Disables TCG/TPM support
Page 139
WSB-9452 PICMG 1.0 CPU Card
6.3.11 USB Configuration
Use the USB Configuration menu (BIOS Menu 15) to read USB configuration
information and configure the USB settings.
BIOS Menu 15: USB Configuration
USB Configuration
The USB Configuration field shows the system USB configuration. The items listed are:
Module Version: x.xxxxx.xxxxx
USB Devices Enabled
The USB Devices Enabled field lists the USB devices that are enabled on the system
Page 140
WSB-9452 PICMG 1.0 CPU Card
USB Function [8 USB Ports]
Use the USB Function BIOS option to disable USB function support or to set the number
of USB ports to activate.
Disabled
USB function support disabled
2 USB Ports
Two USB ports are activated.
4 USB Ports
Four USB ports are activated.
6 USB Ports
Six USB ports are activated.
8 USB Ports
DEFAULT
Eight USB ports are activated.
USB 2.0 Controller [Enabled]
Use the USB 2.0 Controller BIOS option to enable or disable the USB 2.0 controller
Enabled
DEFAULT
Disabled
USB 2.0 controller enabled
USB 2.0 controller disabled
Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support.
Normally if this option is not enabled, any attached USB mouse or USB keyboard does not
become available until a USB compatible operating system is fully booted with all USB
drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard
can control the system even when there is no USB driver loaded onto the system.
Page 141
WSB-9452 PICMG 1.0 CPU Card
Legacy USB support disabled
Disabled
Enabled
DEFAULT
Legacy USB support enabled
Legacy USB support disabled if no USB devices are
Auto
connected
USB2.0 Controller Mode [HiSpeed]
Use the USB2.0 Controller Mode option to set the speed of the USB2.0 controller.
The controller is capable of operating at 12Mb/s
FullSpeed
HiSpeed
DEFAULT
The controller is capable of operating at 480Mb/s
BIOS EHCI Handoff [Enabled]
Use the BIOS EHCI Handoff option for systems running OSes that do not have EHCI
hand-off support. The EHCI ownership change is managed by the EHCI driver.
Systems with OSes that do not support EHCI can
Disabled
use the EHCI handoff functionality.
Enabled
DEFAULT
Systems with OSes that do not support EHCI cannot
use the EHCI handoff functionality.
Page 142
WSB-9452 PICMG 1.0 CPU Card
6.4 PCI/PnP
Use the PCI/PnP menu (BIOS Menu 16) to configure advanced PCI and PnP settings.
WARNING:
Setting wrong values for the BIOS selections in the PCIPnP BIOS
menu may cause the system to malfunction.
Page 143
WSB-9452 PICMG 1.0 CPU Card
Page 144
WSB-9452 PICMG 1.0 CPU Card
BIOS Menu 16: PCI/PnP Configuration
Clear NVRAM [No]
Use the Clear NVRAM option to specify if the NVRAM (Non-Volatile RAM) is cleared
when the power is turned off.
No
Yes
DEFAULT
System does not clear NVRAM during system boot
System clears NVRAM during system boot
Page 145
WSB-9452 PICMG 1.0 CPU Card
Plug & Play O/S [No]
Use the Plug & Play O/S BIOS option to specify whether system plug and play devices
are configured by the operating system or the BIOS.
DEFAULT
No
If the operating system does not meet the Plug and Play
specifications, this option allows the BIOS to configure all the
devices in the system.
This setting allows the operating system to change the
Yes
interrupt, I/O, and DMA settings. Set this option if the system
is running Plug and Play aware operating systems.
PCI Latency Timer [64]
Use the PCI Latency Timer option to specify the PCI latency time. The latency time is
measured in units of PCI clock cycles for the PCI device latency timer register.
Configuration options are:
32
64
96
128
160
192
224
248
Page 146
Default
WSB-9452 PICMG 1.0 CPU Card
Allocate IRQ to PCI VGA [Yes]
Use the Allocate IRQ to PCI VGA option to restrict the system from giving the VGA
adapter card an interrupt address.
Yes
DEFAULT
No
Assigns an IRQ to a PCI VGA card if card requests IRQ
Does not assign IRQ to a PCI VGA card even if the card
requests an IRQ
Palette Snooping [Disabled]
Use the Palette Snooping option to enable or disable the palette snooping function.
Disabled
DEFAULT
Unless the VGA card manufacturer requires palette
snooping to be enabled, this option should be disabled.
Enabled
PCI devices are informed that an ISA based Graphics
device is installed in the system so the ISA based
Graphics card functions correctly. This does not
necessarily indicate a physical ISA adapter card. The
graphics chipset can be mounted on a PCI card. Always
check with the adapter card manual first, before
modifying the default settings in the BIOS.
Page 147
WSB-9452 PICMG 1.0 CPU Card
PCI IDE BusMaster [Enabled]
Use the PCI IDE BusMaster BIOS option to enable or prevent PCI IDE busmastering.
Busmastering is prevented
Disabled
Enabled
DEFAULT
IDE controller on the PCI local bus has mastering
capabilities
OffBoard PCI/ISA IDE Card [Auto]
Use the OffBoard PCI/ISA IDE Card BIOS option to select the OffBoard PCI/ISA IDE
Card.
Auto
DEFAULT
The location of the Off Board PCI IDE adapter card is
automatically detected by the AMIBIOS.
PCI Slot 1
PCI Slot 1 is selected as the location of the OffBoard
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 1.
PCI Slot 2
PCI Slot 2 is selected as the location of the OffBoard
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 2.
PCI Slot 3
PCI Slot 3 is selected as the location of the OffBoard
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 3.
PCI Slot 4
PCI Slot 4 is selected as the location of the OffBoard
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 4.
Page 148
WSB-9452 PICMG 1.0 CPU Card
PCI Slot 5 is selected as the location of the OffBoard
PCI Slot 5
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 5.
PCI Slot 6 is selected as the location of the OffBoard
PCI Slot 6
PCI IDE adapter card. Only select this slot if the
adapter card is installed in PCI Slot 6.
IRQ# [Available]
Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral
device.
Available
DEFAULT
The specified IRQ is available to be used by
PCI/PnP devices
Reserved
The specified IRQ is reserved for use by Legacy ISA
devices
Available IRQ addresses are:
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ 11
IRQ 14
IRQ 15
Page 149
WSB-9452 PICMG 1.0 CPU Card
DMA Channel# [Available]
Use the DMA Channel# option to assign a specific DMA channel to a particular PCI/PnP
device.
Available
DEFAULT
The specified DMA is available to be used by
PCI/PnP devices
The specified DMA is reserved for use by Legacy
Reserved
ISA devices
Available DMA Channels are:
DM Channel 0
DM Channel 1
DM Channel 3
DM Channel 5
DM Channel 6
DM Channel 7
Reserved Memory Size [Disabled]
Use the Reserved Memory Size BIOS option to specify the amount of memory that
should be reserved for legacy ISA devices.
Disabled
Page 150
DEFAULT
No memory block reserved for legacy ISA devices
16K
16KB reserved for legacy ISA devices
32K
32KB reserved for legacy ISA devices
64K
54KB reserved for legacy ISA devices
WSB-9452 PICMG 1.0 CPU Card
6.5 Boot
Use the Boot menu (BIOS Menu 17) to configure system boot options.
BIOS Menu 17: Boot
6.5.1 Boot Settings Configuration
Use the Boot Settings Configuration menu (BIOS Menu 18) to configure advanced
system boot options.
Page 151
WSB-9452 PICMG 1.0 CPU Card
BIOS Menu 18: Boot Settings Configuration
Quick Boot [Enabled]
Use the Quick Boot BIOS option to make the computer speed up the boot process.
No POST procedures are skipped
Disabled
Enabled
DEFAULT
Some POST procedures are skipped to decrease
the system boot time
Page 152
WSB-9452 PICMG 1.0 CPU Card
Quiet Boot [Disabled]
Use the Quiet Boot BIOS option to select the screen display when the system boots.
Disabled
DEFAULT
Normal POST messages displayed
OEM Logo displayed instead of POST messages
Enabled
AddOn ROM Display Mode [Force BIOS]
Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory)
messages to be displayed.
Force BIOS
DEFAULT
The system forces third party BIOS to display
during system boot.
The system displays normal information during
Keep Current
system boot.
Bootup Num-Lock [On]
Use the Bootup Num-Lock BIOS option to specify if the number lock setting must be
modified during boot up.
Off
Does not enable the keyboard Number Lock automatically. To
use the 10-keys on the keyboard, press the Number Lock key
located on the upper left-hand corner of the 10-key pad. The
Number Lock LED on the keyboard lights up when the Number
Lock is engaged.
Page 153
WSB-9452 PICMG 1.0 CPU Card
On
DEFAULT
Allows the Number Lock on the keyboard to be enabled
automatically when the computer system boots up. This allows
the immediate use of the 10-key numeric keypad located on
the right side of the keyboard. To confirm this, the Number
Lock LED light on the keyboard is lit.
PS/2 Mouse Support [Auto]
Use the PS/2 Mouse Support option adjusts PS/2 mouse support capabilities.
PS/2 mouse support is disabled and prevented from
Disabled
using system resources.
Allows the system to use a PS/2 mouse.
Enabled
Auto
DEFAULT
The system auto-adjusts PS/2 mouse support.
Giga LAN Boot ROM Support [Disabled]
The Giga LAN Boot ROM Support option enables the system to be booted from a
remote system.
Disabled
DEFAULT
Cannot be booted from a remote system through the
LAN
Enabled
Can be booted from a remote system through the
LAN
Page 154
WSB-9452 PICMG 1.0 CPU Card
6.5.2 Boot Device Priority
Use the Boot Device Priority menu (BIOS Menu 19) to specify the boot sequence from
the available devices. Possible boot devices may include:
1st FLOPPY DRIVE
HDD
CD/DVD
BIOS Menu 19: Boot Device Priority Settings
Page 155
WSB-9452 PICMG 1.0 CPU Card
6.5.3 Hard Disk Drives
The Hard Disk Drives menu (BIOS Menu 20) specifies the boot sequence of the
available HDDs. When the menu is opened, the HDDs connected to the system are listed
as shown below:
1st Drive
[HDD: PM-(part number)]
2nd Drive
[HDD: PS-(part number)]
3rd Drive
[HDD: SM-(part number)]
4th Drive
[HDD: SM-(part number)]
BIOS Menu 20: Hard Disk Drives
Page 156
WSB-9452 PICMG 1.0 CPU Card
NOTE:
Only the drives connected to the system are shown. For example, if
only two HDDs are connected only “1st Drive” and “2nd Drive” are
listed.
The boot sequence from the available devices is selected. If the “1st Drive” option is
selected a list of available HDDs is shown. Select the first HDD system boots from. If the
“1st Drive” is not used for booting this option may be disabled.
6.5.4 Removable Drives
Use the Removable Drives menu (BIOS Menu 21) to specify the boot sequence of the
available FDDs. When the menu is opened, the FDDs connected to the system are listed
as shown below:
1st Drive
NOTE:
Only the drives connected to the system are shown. For example, if
only one FDD is connected only “1st Drive” is listed.
The boot sequence from the available devices is selected. If the “1st Drive” option is
selected a list of available removable drives is shown. Select the first drive the system
boots from. If the “1st Drive” is not used for booting this option may be disabled.
Page 157
WSB-9452 PICMG 1.0 CPU Card
BIOS Menu 21: Removable Drives
Page 158
WSB-9452 PICMG 1.0 CPU Card
6.6 Security
Use the Security menu (BIOS Menu 22) to set system and user passwords.
BIOS Menu 22: Security
Change Supervisor Password
Use the Change Supervisor Password to set or change a supervisor password. The
default for this option is Not Installed. If a supervisor password must be installed, select
this field and enter the password. After the password has been added, Install appears
next to Change Supervisor Password.
Page 159
WSB-9452 PICMG 1.0 CPU Card
Change User Password
Use the Change User Password to set or change a user password. The default for this
option is Not Installed. If a user password must be installed, select this field and enter the
password. After the password has been added, Install appears next to Change User
Password.
Page 160
WSB-9452 PICMG 1.0 CPU Card
6.7 Chipset
Use the Chipset menu (BIOS Menu 23) to access the Northbridge and Southbridge
configuration menus.
WARNING:
Setting the wrong values for the Chipset BIOS selections in the Chipset
BIOS menu may cause the system to malfunction.
BIOS Menu 23: Chipset
Page 161
WSB-9452 PICMG 1.0 CPU Card
6.7.1 Northbridge Configuration
Use the Northbridge Configuration menu (BIOS Menu 24) to configure the Northbridge
chipset.
BIOS Menu 24: Northbridge Chipset Configuration
DRAM Frequency [Auto]
Use the DRAM Frequency option to specify the DRAM frequency or allow the system to
automatically detect the DRAM frequency.
Auto
400MHz
Page 162
DEFAULT
Automatically selects the DRAM frequency
Sets the DRAM frequency to 400MHz
WSB-9452 PICMG 1.0 CPU Card
533MHz
Sets the DRAM frequency to 533MHz
667MHz
Sets the DRAM frequency to 667MHz
Configure DRAM Timing by SPD [Enabled]
Use the Configure DRAM Timing by SPD option to determine if the system uses the
SPD (Serial Presence Detect) EEPROM to configure the DRAM timing. The SPD
EEPROM contains all necessary DIMM specifications including the speed of the individual
components such as CAS and bank cycle time as well as valid settings for the module and
the manufacturer's code. The SPD enables the BIOS to read the spec sheet of the DIMMs
on boot-up and then adjust the memory timing parameters accordingly.
DRAM timing parameters are manually set using the
Disabled
DRAM sub-items
Enabled
DEFAULT
DRAM timing parameter are set according to the
DRAM Serial Presence Detect (SPD)
If the Configure DRAM Timing by SPD option is disabled, the following configuration
options appear.
DRAM CAS# Latency [5]
DRAM RAS# to CAS# Delay [6 DRAM Clocks]
DRAM RAS# Precharge [6 DRAM Clocks]
DRAM RAS# Activate to Precha [15 DRAM Clocks]
Memory Hole [Disabled]
Use the Memory Hole option to reserve memory space between 15MB and 16MB for ISA
expansion cards that require a specified area of memory to work properly. If an older ISA
expansion card is used, please refer to the documentation that came with the card to see if
it is necessary to reserve the space.
Page 163
WSB-9452 PICMG 1.0 CPU Card
Disabled
DEFAULT
Memory is not reserved for ISA expansion cards
Between 15MB and 16MB of memory is reserved for
15MB – 16MB
ISA expansion cards
Boots Graphics Adapter Priority [IGD]
Use the Boots Graphics Adapter Priority option to select the graphics controller used as
the primary boot device. Select either an integrated graphics controller (IGD) or a
combination of PCI graphics controller, a PCI express (PEG) controller or an IGD.
Configuration options are listed below:
IGD
Default
PCI/IGD
PCI/PEG
PEG/IGD
PEG/PCI
Internal Graphics Mode Select [Enabled, 8MB]
Use the Internal Graphic Mode Select option to specify the amount of system memory
that can be used by the Internal graphics device.
Disable
1MB of memory used by internal graphics device
Enable, 1MB
Enable, 8MB
Page 164
DEFAULT
8MB of memory used by internal graphics device
WSB-9452 PICMG 1.0 CPU Card
6.7.1.1 Video Function Configuration
Use the Video Function Configuration menu (BIOS Menu 25) to configure the video
device connected to the system.
BIOS Menu 25: Video Function Configuration
DVMT Mode Select [DVMT Mode]
Use the DVMT Mode Select option to select the Intel Dynamic Video Memory Technology
(DVMT) operating mode.
Page 165
WSB-9452 PICMG 1.0 CPU Card
A fixed portion of graphics memory is reserved as
Fixed Mode
graphics memory.
DVMT Mode
DEFAULT
Graphics
memory
is
dynamically
allocated
according to the system and graphics needs.
Combo Mode
A fixed portion of graphics memory is reserved as
graphics memory. If more memory is needed,
graphics
memory
is
dynamically
allocated
according to the system and graphics needs.
DVMT/FIXED Memory [128MB]
Use the DVMT/FIXED Memory option to specify the maximum amount of memory that
can be allocated as graphics memory. This option can only be configured for if DVMT
Mode or Fixed Mode is selected in the DVMT Mode Select option. If Combo Mode is
selected, the maximum amount of graphics memory is 128MB. Configuration options are
listed below.
64MB
128MB
DEFAULT
Maximum DVMT
Boot Display Device [CRT on Port 0]
Use the Boot Display Device option to select the display device used by the system
when it boots. Configuration option is listed below.
CRT on Port 0
CRT and DFP
CRT and LCD
Page 166
DEFAULT
WSB-9452 PICMG 1.0 CPU Card
Flat Panel Type [640*480]
Use the Flat Panel Type option to select the type of flat panel connected to the system.
Configuration options are listed below.
640*480
800*600
1024*768 (18 bits)
DEFAULT
1280*1024 (36bits)
1400*1050 (36bits)
1600*1200 (36bits)
1280*768
1680*1050 (36bits)
1920*1200 (36bits)
1024*768 (48 bits)
1440 x 900 (36 bits)
1440 x 900 (48 bits)
1280 x 800 (18 bits)
1260 x 600 (18 bits)
2048 x 1536 (36 bits)
Local Flat Panel Scaling [Auto]
Use the Local Flat Panel Scaling option to select the method of scaling for the flat panel
screen attached to the system.
Auto
DEFAULT
Scaling is automatic
Forced Scaling
Scaling is forced
Disabled
Scaling is disabled
TV Connector [Auto]
Use the TV Connector option to select the connector that is used to connect the system
to the television. The configuration option is listed below.
Page 167
WSB-9452 PICMG 1.0 CPU Card
Auto
DEFAULT
Composite
Component
Composite & RGB
S-Video
SCART Composite
SCART Compos. & RGB
SCART Compos. & S-Vdo
SMPTE253 Compon. RGB
HDTV Output [Auto]
Use the HDTV Output option to select the number of vertical lines in each frame, the
method the HDTV connected to the system scans and the frequency of the frames.
Two scanning types can be selected: interlaced (i) or progressive (p). Interlaced scanning
divides and presents each video frame as two fields. The first field presents the odd lines
and the second field presents the even lines. In progressive scanning, the image is
refreshed from top to bottom, one line after the other.
Configuration options are listed below:
Option
Scan Type
Vertical Lines
Frame Frequency
Auto
Auto
Auto
Auto
480i60
Interlaced
240 per field (480 per frame)
60 frames per second
480p60
Progressive
480 per frame
60 frames per second
576i50
Interlaced
283 per field (576 per frame)
50 frames per second
576p50
Progressive
576 per frame
50 frames per second
720p60
Progressive
720 per frame
60 frames per second
1080i50
Interlaced
540 per field (1080 per frame)
50 frames per second
1080i60
Interlaced
540 per field (1080 per frame)
60 frames per second
Page 168
WSB-9452 PICMG 1.0 CPU Card
1080p24
Progressive
1080 per frame
24 frames per second
1080p25
Progressive
1080 per frame
25 frames per second
1080p30
Progressive
1080 per frame
30 frames per second
1080p50
Progressive
1080 per frame
50 frames per second
1080p60
Progressive
1080 per frame
60 frames per second
TV Standard [VBIOS-Default]
Use the TV Standard option to select the standard of the television connected to the
system. The configuration options are listed below.
VBIOS-Default
DEFAULT
NTSC
PAL
SECAM
SMPTE240M
ITU-R television
SMPTE295M
SMPTE296M
ETA-770.2
ETA-770.3
Page 169
WSB-9452 PICMG 1.0 CPU Card
6.7.2 Southbridge Configuration
The Southbridge Configuration menu (BIOS Menu 26) the Southbridge chipset to be
configured.
BIOS Menu 26:Southbridge Chipset Configuration
Page 170
WSB-9452 PICMG 1.0 CPU Card
Audio Controller [AC`97 Audio]
The Audio Controller option allows selection of the audio controller to use.
DEFAULT
Azalia
The Intel® High Definition Audio controller is enabled
AC`97 Audio
The on-board AC’97 controller is enabled
All Disabled
All audio controllers are disabled
OnBoard LAN1 [Auto]
The OnBoard LAN1 option enables or disables the on-board LAN1.
Auto
DEFAULT
The on-board LAN1 controller is automatically detected
and enabled
Enabled
The on-board LAN1 controller is manually enabled
Disabled
The on-board LAN1 controller is manually disabled
On-board LAN2 [Auto]
The On-board LAN2 option enables or disables the on-board LAN2.
Auto
DEFAULT
The on-board LAN2 controller is automatically detected
and enabled
Enabled
The on-board LAN2 controller is manually enabled
Disabled
The on-board LAN2 controller is manually disabled
Mini Card [Auto]
The Mini Card option enables or disables the PCI Express Mini Card.
Page 171
WSB-9452 PICMG 1.0 CPU Card
Auto
DEFAULT
The PCI Express Mini Card is automatically detected
and enabled
Enabled
The PCI Express Mini Card is manually enabled
Disabled
The PCI Express Mini Card is manually disabled
SATA Controller
Use the SATA Controller option to enable or disable the onboard SATA controller.
Auto
DEFAULT
The onboard SATA controller is automatically
detected and enabled
Enabled
The SATA controller is manually enabled
Disabled
The SATA controller is manually disabled
SATA Controller Mode Select
Use the SATA Controller Mode Select option to set the mode of the JMB363 SATA
controller. If the RAID function is going to be used this option must be set to RAID mode.
Disabled
DEFAULT
The onboard PCI SATA controller is disabled
IDE
The SATA controller is set as an IDE device
RAID
The SATA controller is set as a RAID device
AHCI
The SATA controller is set as an Advanced Host
Controller Interface (AHCI)
Page 172
WSB-9452 PICMG 1.0 CPU Card
6.8 Exit
Use the Exit menu (BIOS Menu 27) to load default BIOS values, optimal failsafe values
and to save configuration changes.
BIOS Menu 27:Exit
Save Changes and Exit
Use the Save Changes and Exit option to save the changes made to the BIOS options
and to exit the BIOS configuration setup program.
Discard Changes and Exit
Use the Discard Changes and Exit option to exit the BIOS configuration setup program
without saving the changes made to the system.
Page 173
WSB-9452 PICMG 1.0 CPU Card
Discard Changes
Use the Discard Changes option to discard the changes and remain in the BIOS
configuration setup program.
Load Optimal Defaults
Use the Load Optimal Defaults option to load the optimal default values for each of the
parameters on the Setup menus. F9 key can be used for this operation.
Load Failsafe Defaults
Use the Load Failsafe Defaults option to load failsafe default values for each of the
parameters on the Setup menus. F8 key can be used for this operation.
Page 174
WSB-9452 PICMG 1.0 CPU Card
Chapter
7
7 Software drivers
Page 175
WSB-9452 PICMG 1.0 CPU Card
7.1 Available Software Drivers
NOTE:
The content of the CD may vary throughout the life cycle of the product
and is subject to change without prior notice. Visit the IEI website or
contact technical support for the latest updates.
The WSB-9452 motherboard has the following software drivers:
Intel® Chipset Driver Installation
VGA Utilities Driver
LAN Driver (for GbE LAN) Installation
Audio Driver (ALC655 / ALC883) Installation
SATA Driver Installation
All drivers can be found on the CD that came with the motherboard. To install the drivers
please follow the instructions in the sections below.
7.2 Chipset Driver Installation
To install the chipset driver, please follow the steps below:
Step 1: Insert the CD into the system that contains the WSB-9452 board. Open the
1-INF directory and locate the icon for the infinst_autol.exe installation file.
Once located, use the mouse to double click the icon.
Page 176
WSB-9452 PICMG 1.0 CPU Card
Step 2: The “InstallShield Wizard Preparation Screen” in Figure 7-1 appears.
Figure 7-1: InstallShield Wizard Preparation Screen
Step 3: The “Welcome” window in Figure 7-2 appears next.
Figure 7-2: Welcome Screen
Page 177
WSB-9452 PICMG 1.0 CPU Card
Step 4: Click “NEXT” and the license agreement shown in Figure 7-3 appears.
Figure 7-3: License Agreement
Page 178
WSB-9452 PICMG 1.0 CPU Card
Step 5: Agree to the license terms by clicking “YES”. The “Readme” in Figure 7-4
appears.
Figure 7-4: Readme Information
Page 179
WSB-9452 PICMG 1.0 CPU Card
Step 6: Click “YES”. The driver is installed on the computer. After the installation is
complete, the installation complete screen shown in Figure 7-5 appears. Select
the preferred option and click “FINISH” to complete the installation process.
Figure 7-5: Restart the Computer
Page 180
WSB-9452 PICMG 1.0 CPU Card
7.3 VGA Driver
To install the VGA driver, please follow the steps below:
Step 1: Insert the Utility CD that came with the motherboard into the system CD drive.
Step 2: Open the X:\2-VGA\WIN2K_XP directory (where X:\ is the system CD drive)
and double-click the win2k_xp1420.exe installation file.
Step 3: The Starting Install Shield Wizard appears (Figure 7-6).
Figure 7-6: Starting Install Shield Wizard Screen
Page 181
WSB-9452 PICMG 1.0 CPU Card
Step 4: The Preparing Setup window appears next (Figure 7-7).
Figure 7-7: Preparing Setup Screen
Page 182
WSB-9452 PICMG 1.0 CPU Card
Step 5: A Welcome screen shown in Figure 7-8 appears. Click NEXT to continue the
installation.
Figure 7-8: VGA Driver Installation Welcome Screen
Page 183
WSB-9452 PICMG 1.0 CPU Card
Step 6: A license agreement shown in Figure 7-9 appears. Read through the license
agreement.
Figure 7-9: VGA Driver License Agreement
Step 7: Accept the terms and conditions stipulated in the license agreement by clicking
the “YES” button (Figure 7-9). The installation notice shown in Figure 7-10
appears.
Figure 7-10: VGA Driver Installing Notice
Page 184
WSB-9452 PICMG 1.0 CPU Card
Step 8: After the driver installation process is complete, a confirmation screen shown in
Figure 7-11 appears.
Figure 7-11: VGA Driver Installation Complete
Step 9: The confirmation screen shown in Figure 7-11 allows user to restart the
computer immediately after the installation is complete or to restart the computer
later. For the settings to take effect the computer must be restarted. Once
decided when to restart the computer, click the “FINISH” button.
Page 185
WSB-9452 PICMG 1.0 CPU Card
7.4 Broadcom LAN Driver (for GbE LAN) Installation
To install the Broadcom LAN driver, please follow the steps below.
Step 1: Open Windows Control Panel (Figure 7-12).
Figure 7-12: Access Windows Control Panel
Page 186
WSB-9452 PICMG 1.0 CPU Card
Step 2: Double click the System icon (Figure 7-13).
Figure 7-13: Double Click the System Icon
Page 187
WSB-9452 PICMG 1.0 CPU Card
Step 3: Click the Hardware Tab, then double click Device Manager (Figure 7-14).
Figure 7-14: Double Click the Device Manager Tab
Step 4: A list of system hardware devices appears (Figure 7-15).
Figure 7-15: Device Manager List
Step 5: Double click the listed device that has question marks next to it. (This means
Windows does not recognize the device).
Page 188
WSB-9452 PICMG 1.0 CPU Card
Step 6: The Device Driver Wizard appears (Figure 7-16). Click NEXT to continue.
Figure 7-16: Search for Suitable Driver
Page 189
WSB-9452 PICMG 1.0 CPU Card
Step 7: Select “Specify a Location” in the Locate Driver Files window (Figure 7-17).
Click NEXT to continue.
Figure 7-17: Locate Driver Files
Page 190
WSB-9452 PICMG 1.0 CPU Card
Step 8: Select the proper OS folder under the “X:\3-LAN\E:\3-LAN\BoadCom
BCM5787” directory (Figure 7-18) in the location browsing window, where “X:\”
is the system CD drive.
Figure 7-18: Location Browsing Window
Step 9: Click OK to continue. A driver files location menu window appears. Click NEXT to
continue. The driver is installed.Step 0:
Page 191
WSB-9452 PICMG 1.0 CPU Card
7.5 Realtek HD Audio Driver (ALC883) Installation
To install the Realtek High Definition (HD) Audio driver, please follow the steps below.
7.5.1 BIOS Setup
Step 1: Enter the BIOS setup. To do this, reboot the system and press DEL during
POST.
Step 2: Go to the Southbridge Configuration menu. Set the Audio Controller option to
[Azalia]. See Section 6.7.2 for details.
Step 3: Press F10 to save the changes and exit the BIOS setup. The system reboots.
Step 0:
7.5.2 Driver Installation
Step 1: Insert the SIS Solution CD that came with the package.
Step 2: From the main driver menu, navigate to X:\4-AUDIO\AC-KIT883HD\Windows
(or other appropriate OS). X:\ represents the system CD drive. A new window
appears showing the folder contents (Figure 6-26).
Page 192
WSB-9452 PICMG 1.0 CPU Card
Figure 7-19: 4-AUDIO\AC-KIT883HD\Windows Folder
Step 3: Double-click the WDM_R140 icon to begin the driver installation process.
Page 193
WSB-9452 PICMG 1.0 CPU Card
Step 4: Once the WDM_R140 icon is double clicked, the contents of the installation
package are extracted. See Figure 7-20.
Figure 7-20: HD Audio Driver Setup Extracting Files
Page 194
WSB-9452 PICMG 1.0 CPU Card
Step 5: The Welcome screen appears. Click NEXT. See Figure 7-21.
Figure 7-21: HD Audio Driver Setup Welcome Screen
Page 195
WSB-9452 PICMG 1.0 CPU Card
Step 6: The driver is automatically installed.
Step 7: After the driver installation process is complete, a confirmation screen shown in
Figure 7-22 appears.
Figure 7-22: HD Audio Driver Installation Complete
Step 8: The confirmation screen shown in Figure 7-22 allows you to restart the
computer immediately after the installation is complete or to restart the computer
later. For the settings to take effect the computer must be restarted. Once you
have decided when to restart the computer, click the “FINISH” button. Step 0:
Page 196
WSB-9452 PICMG 1.0 CPU Card
7.6 Realtek AC`97 Audio Driver (ALC665) Installation
To install the Realtek AC `97 audio driver, please follow the steps below.
7.6.1 BIOS Setup
Step 1: Enter the BIOS setup. To do this, reboot the system and press DEL during
POST.
Step 2: Go to the Southbridge Configuration menu. Set the Audio Controller option to
[AC`97]. See Section 6.7.2 for details.
Step 3: Press F10 to save the changes and exit the BIOS setup. The system reboots.
Step 0:
7.6.2 Driver Installation
Step 1: Insert the SIS Solution CD that came with the package.
Step 2: From the main driver menu, navigate to X:\4-AUDIO\AC-KIT08R\Windows (or
other appropriate OS). X:\ represents the system CD drive. A new window
appears showing the folder contents (Figure 7-23).
Page 197
WSB-9452 PICMG 1.0 CPU Card
Figure 7-23: CD 4-AUDIO\AC-KIT08R\Windows Folder
Step 3: Double-click the Setup.exe file to begin the driver installation process.
Step 4: Once you double click the Setup icon, the install shield wizard for the audio
driver starts. See Figure 7-24.
Figure 7-24: AC`97 Audio Driver Install Shield Wizard Starting
Step 5: The Realtek Audio Setup prepares the install shield to guide you through the
rest of the setup process. See Figure 7-21.
Page 198
WSB-9452 PICMG 1.0 CPU Card
Figure 7-25: AC`97 Audio Driver Setup Preparation
Page 199
WSB-9452 PICMG 1.0 CPU Card
Step 6: After the install shield is prepared, the welcome screen shown in Figure 7-26
appears. To continue the installation process, click the “NEXT” button. The install
shield starts to configure the new software as shown in Figure 7-27.
Figure 7-26: AC`97 Audio Driver Welcome Screen
Page 200
WSB-9452 PICMG 1.0 CPU Card
Figure 7-27: AC`97 Audio Driver Software Configuration
Page 201
WSB-9452 PICMG 1.0 CPU Card
Step 7: At this stage the “Digital Signal Not Found” screen appears (Figure 7-28). To
continue the installation process, click the “YES” button.
Figure 7-28: AC`97 Audio Driver Digital Signal
Page 202
WSB-9452 PICMG 1.0 CPU Card
Step 8: After clicking the “YES” button in Figure 7-28, the installation of the driver begins
(Figure 7-29).
Figure 7-29: AC`97 Audio Driver Installation Begins
Page 203
WSB-9452 PICMG 1.0 CPU Card
Step 9: After the driver installation process is complete, a confirmation screen shown in
Figure 7-30 appears.
Figure 7-30: AC`97 Audio Driver Installation Complete
Step 10: The confirmation screen shown in Figure 7-30 allows you to restart the
computer immediately after the installation is complete or to restart the computer
later. For the settings to take effect the computer must be restarted. Once you
have decided when to restart the computer, click the “FINISH” button. Step 0:
Page 204
WSB-9452 PICMG 1.0 CPU Card
Appendix
A
A BIOS Configuration
Options
Page 205
WSB-9452 PICMG 1.0 CPU Card
A.1 BIOS Configuration Options
Below is a list of BIOS configuration options described in Chapter 0.
System Overview ................................................................................................ 108
Intel(R) SpeedStep(tm) tech. [Automatic] ........................................................ 112
ATA/IDE Configuration [Compatible]................................................................ 113
Legacy IDE Channels [SATA Pri, PATA Sec]................................................... 114
IDE Master and IDE Slave .................................................................................. 114
Type [Auto] .......................................................................................................... 115
ZIP ........................................................................................................................ 116
LS-120 .................................................................................................................. 116
LBA/Large Mode [Auto]...................................................................................... 116
Block (Multi Sector Transfer) [Auto] ................................................................. 117
PIO Mode [Auto].................................................................................................. 117
DMA Mode [Auto]................................................................................................ 118
S.M.A.R.T [Auto].................................................................................................. 118
32Bit Data Transfer [Enabled] ........................................................................... 118
Floppy A/B [1.44 MB 3½”] .................................................................................. 119
On-board Floppy Controller [Enabled] ............................................................. 121
Floppy Drive Swap [Disabled] ........................................................................... 121
Serial Port1 Address [3F8/IRQ4] ....................................................................... 121
Serial Port1 Mode [Normal]................................................................................ 122
Serial Port2 Address [2F8/IRQ3] ....................................................................... 122
Serial Port2 Mode [Normal]................................................................................ 122
Parallel Port Address [Disabled] ....................................................................... 123
Parallel Port Mode [Normal]............................................................................... 123
Parallel Port IRQ [IRQ7]...................................................................................... 124
CPU FAN Mode Setting: [Full On mode] .......................................................... 125
CPU Temp. Limit of OFF .................................................................................... 125
CPU Temp. Limit of Start ................................................................................... 125
CPU Temp. Limit of Full ..................................................................................... 125
Page 206
WSB-9452 PICMG 1.0 CPU Card
CPU Fan Start PWM ............................................................................................ 125
Slope PWM 1: 0 PWM, 1 PWM (Default), 2 PWM, 4 PWM, 8 PWM, 16 PWM, 32
PWM or 64 PWM ...................................................................................................... 125
CPU Fan PWM Control ....................................................................................... 125
ACPI Aware O/S [Yes] ........................................................................................ 127
Suspend mode [Auto] ........................................................................................ 129
Repost Video on S3 Resume [Yes] ................................................................... 129
Power Management/APM [Enabled].................................................................. 130
Restore on AC Power Loss by IO [Last State]................................................. 131
Power Button Mode [On/Off] ............................................................................. 131
Resume on Ring [Disabled] ............................................................................... 131
Resume on PME# [Disabled] ............................................................................. 132
Resume On RTC Alarm [Disabled].................................................................... 132
RTC Alarm Date (Days) ...................................................................................... 132
RTC Alarm Time .................................................................................................. 132
MPS Revision [1.4].............................................................................................. 133
Remote Access [Disabled]................................................................................. 134
Serial Port Number ............................................................................................. 135
Serial Port Mode.................................................................................................. 135
Flow Control ........................................................................................................ 135
Redirection after BIOS POST............................................................................. 135
Terminal Type...................................................................................................... 135
VT-UTF8 Combo Key Support ........................................................................... 135
Sredir Memory Display Delay ............................................................................ 135
Serial Port Number [COM1] ............................................................................... 135
Base Address, IRQ [2F8h,3]............................................................................... 136
Serial Port Mode [115200 8,n,1]......................................................................... 136
Flow Control [None]............................................................................................ 136
Redirection After BIOS POST [Always] ............................................................ 137
Terminal Type [ANSI] ......................................................................................... 137
VT-UTF8 Combo Key Support [Disabled]......................................................... 137
Page 207
WSB-9452 PICMG 1.0 CPU Card
Sredir Memory Display Delay [Disabled].......................................................... 138
TCG/TPM Support [No]....................................................................................... 139
USB Configuration.............................................................................................. 140
USB Devices Enabled......................................................................................... 140
USB Function [8 USB Ports].............................................................................. 141
USB 2.0 Controller [Enabled]............................................................................. 141
Legacy USB Support [Enabled]......................................................................... 141
USB2.0 Controller Mode [HiSpeed]................................................................... 142
BIOS EHCI Handoff [Enabled] ........................................................................... 142
Clear NVRAM [No]............................................................................................... 145
Plug & Play O/S [No]........................................................................................... 146
PCI Latency Timer [64] ....................................................................................... 146
Allocate IRQ to PCI VGA [Yes] .......................................................................... 147
Palette Snooping [Disabled] .............................................................................. 147
PCI IDE BusMaster [Enabled] ............................................................................ 148
OffBoard PCI/ISA IDE Card [Auto] .................................................................... 148
IRQ# [Available]................................................................................................ 149
DMA Channel# [Available] ................................................................................. 150
Reserved Memory Size [Disabled] .................................................................... 150
Quick Boot [Enabled] ......................................................................................... 152
Quiet Boot [Disabled] ......................................................................................... 153
AddOn ROM Display Mode [Force BIOS] ......................................................... 153
Bootup Num-Lock [On] ...................................................................................... 153
PS/2 Mouse Support [Auto] ............................................................................... 154
Giga LAN Boot ROM Support [Disabled].......................................................... 154
Change Supervisor Password........................................................................... 159
Change User Password...................................................................................... 160
DRAM Frequency [Auto] .................................................................................... 162
Configure DRAM Timing by SPD [Enabled] ..................................................... 163
Memory Hole [Disabled]..................................................................................... 163
Boots Graphics Adapter Priority [IGD] ............................................................. 164
Page 208
WSB-9452 PICMG 1.0 CPU Card
Internal Graphics Mode Select [Enabled, 8MB] ............................................... 164
DVMT Mode Select [DVMT Mode]...................................................................... 165
DVMT/FIXED Memory [128MB] .......................................................................... 166
Boot Display Device [CRT on Port 0]................................................................ 166
Flat Panel Type [640*480]................................................................................... 167
Local Flat Panel Scaling [Auto] ......................................................................... 167
TV Connector [Auto]........................................................................................... 167
HDTV Output [Auto]............................................................................................ 168
TV Standard [VBIOS-Default]............................................................................. 169
Audio Controller [AC`97 Audio] ........................................................................ 171
OnBoard LAN1 [Auto] ........................................................................................ 171
On-board LAN2 [Auto]........................................................................................ 171
Mini Card [Auto] .................................................................................................. 171
SATA Controller .................................................................................................. 172
SATA Controller Mode Select............................................................................ 172
Save Changes and Exit ...................................................................................... 173
Discard Changes and Exit ................................................................................. 173
Discard Changes................................................................................................. 174
Load Optimal Defaults........................................................................................ 174
Load Failsafe Defaults........................................................................................ 174
Page 209
WSB-9452 PICMG 1.0 CPU Card
Appendix
B
B Watchdog Timer
Page 210
WSB-9452 PICMG 1.0 CPU Card
NOTE:
The following discussion applies to DOS environment.
It is
recommended you contact IEI support or visit our website for specific
drivers for more sophisticated operating systems, e.g., Windows and
Linux.
The Watchdog Timer is provided to ensure that standalone systems can always recover
from catastrophic conditions that cause the CPU to crash. This condition may have
occurred by external EMI or a software bug. When the CPU stops working correctly,
Watchdog Timer will either perform a hardware reset (cold boot) or a Non-Maskable
Interrupt (NMI) to bring the system back to a known state.
A BIOS function call (INT 15H) is used to control the Watchdog Timer:
INT 15H:
AH – 6FH Sub-function:
AL – 2:
Sets the Watchdog Timer’s period.
BL:
Time-out value (Its unit-second is dependent on the item “Watchdog
Timer unit select” in CMOS setup).
Table B-1: AH-6FH Sub-function
You have to call sub-function 2 to set the time-out period of Watchdog Timer first. If the
time-out value is not zero, the Watchdog Timer will start counting down. While the timer
value reaches zero, the system will reset. To ensure that this reset condition does not
occur, calling sub-function 2 must periodically refresh the Watchdog Timer. However, the
Watchdog timer will be disabled if you set the time-out value to be zero.
A tolerance of at least 10% must be maintained to avoid unknown routines within the
operating system (DOS), such as disk I/O that can be very time-consuming.
Page 211
WSB-9452 PICMG 1.0 CPU Card
NOTE:
When exiting a program it is necessary to disable the Watchdog Timer,
otherwise the system will reset.
Example program:
; INITIAL TIMER PERIOD COUNTER
;
W_LOOP:
MOV
AX, 6F02H
;setting the time-out value
MOV
BL, 30
;time-out value is 48 seconds
INT
15H
;
; ADD YOUR APPLICATION PROGRAM HERE
;
CMP
EXIT_AP, 1
JNE
W_LOOP
;No, restart your application
MOV
AX, 6F02H
;disable Watchdog Timer
MOV
BL, 0
;
INT
15H
;
; EXIT ;
Page 212
;is your application over?
WSB-9452 PICMG 1.0 CPU Card
Appendix
C
C External AC’97 Audio
CODEC
Page 213
WSB-9452 PICMG 1.0 CPU Card
C.1 Introduction
The audio functionalities of the WSB-9452 CPU card can be implemented using a
separately purchased audio module, the AC-KIT08R-R10. The audio kit is powered by
Realtek ALC655/883, a 16-bit, full duplex AC’97 2.3 compatible audio CODEC with 48KHz
sampling rate. The audio kit functionalities are interfaced through three (3) phone jack
connectors and two (2) pin headers including:
1. A LINE input shared with surround output
2. A MIC input shared with Center and LFE output
3. A LINE output
4. Analog line-level stereo inputs with 5-bit volume control: CDIN1 and AUXIN1.
Both Front_out and Surround_out are equipped with a built-in 50mW/20ohm amplifier.
The ALC655 supports host/soft audio from Intel ICHx chipsets as well as audio controller
based VIA/SIS/Ali/ATI chipset with bundled Windows series drivers (XP/ME/2000/98/NT),
EAX/Direct Sound 3D/I3DL2/A3D compatible sound effect utilities supporting Karaoke, 26
kinds of environment sound emulations with 10-band equalizer, and HRTF 3D positional
audio. The audio kit provides an excellent entertainment package sufficient for today’s
multimedia systems.
Page 214
WSB-9452 PICMG 1.0 CPU Card
Figure C-1: Audio Functionalities via the Audio Kit
Page 215
WSB-9452 PICMG 1.0 CPU Card
C.2 Physical Connection
Figure C-2: Audio Kit Connectors
The audio kit comes with a PCI slot bracket for the installation into a PC case or
rackmount chassis.
Connect the 10-pin header to the J_AUDIO1 header as shown
above, and if necessary, connect the CDIN1 and AUXIN1 to optical drives or other audio
sources, e.g., an MPEG card, using a 4-pin cable. Note that depending on the devices
you connect to, the phone jacks have different functions with different audio installation
modes (2 channel or 5.1 channel modes).
C.3 Driver Installation
The driver installation has been described in Chapter 7.
After reboot, you should be able to find the sound effect configuration utility in Windows
Control Panel (see Figure C-3); and if peripheral speakers have been properly connected,
hear the sound effects.
Page 216
WSB-9452 PICMG 1.0 CPU Card
Figure C-3: Sound Effect Manager Icon
Page 217
WSB-9452 PICMG 1.0 CPU Card
C.4 Sound Effect Configuration
After installing the audio CODEC driver, you should be able to use the multi-channel audio
features now. Click the audio icon from the Notification Area from system task bar (see
Figure C-5). The shortcut to the configuration utility is also available through the Sound
Effect Manager icon in the Control Panel (Figure C-4).
Figure C-4: Sound Effect Manager Icon [Control Panel]
Figure C-5: Sound Effect Manager Icon [Task Bar]
Page 218
WSB-9452 PICMG 1.0 CPU Card
C.5 Sound Effect
You may select a pre-configured sound environment setting with the preset equalizer
settings. You may also load an equalizer setting or make a new equalizer setting using
the “Load EQ Setting” and “Save Preset” button. (See Figure C-7)
Figure C-6: Setting Sound Effects
C.6 Environment Simulation
This is the default screen whenever the configuration utility is opened.
You may select different sound environment modes by a single click on the Environment
pull-down list. There are a total of 23 preset environment modes (see Figure C-7). You
may also fine-tune the environment setting by clicking the Edit button on the right, which
displays an editor window. Select a preset mode you want to edit. Select a preset
mode, and then select one the property value from the list below by a single click. Use
the scroll bar below to adjust properties setting. When the adjustment is done, click the
Save button to proceed.
Page 219
WSB-9452 PICMG 1.0 CPU Card
Figure C-7: Sound Effects Properties Editor
Page 220
WSB-9452 PICMG 1.0 CPU Card
C.7 Karaoke Mode
Figure C-8: Karaoke Mode
The Karaoke mode shown in Figure C-8 allows you to eliminate the vocal of the music
you play or adjust the key to accommodate your range.
The configuration options that come with the Karaoke function include:
1. Voice Cancellation: This checkbox, when selected, disables the vocal part of the
music your play in your computer while the background music remains.
2. Key adjustment: Use the Up or Down arrow icons to find a key that fits your vocal
range.
Page 221
WSB-9452 PICMG 1.0 CPU Card
NOTE:
The Equalizer button on the default display brings you to the same
configuration window as the Equalizer function tab on top of the
window.
C.8 Equalizer Selection
Figure C-9: Equalizer Settings
The equalizer in Figure C-9 allows users to change sound effect parameters.
The
default screen shows equalized values. You may also select preset modes from the
buttons below.
The configurable values include 10 bands of equalizer ranging from
100Hz to 16KHz. Use the scroll bar to fine-tune, and use the Load, Save, Delete, and
Reset buttons to edit your settings.
Page 222
WSB-9452 PICMG 1.0 CPU Card
C.9 Speaker Configuration
Figure C-10: Speaker Configuration
In this functional window, you can configure your multi-channel speaker settings.
Select the audio configuration from the No. of Speakers section on the left by clicking on
one of the check circles.
The configurable options are:
1. Headphone
2. Channel mode for stereo speaker output
3. Channel mode for 4 speaker output
4. Channel mode for 5.1 speaker output
5. Synchronize the phonejack switch with speakers settings
Page 223
WSB-9452 PICMG 1.0 CPU Card
Select a speaker configuration by selecting its check circle, and then click OK to apply the
configuration change.
Connect your speakers to the corresponding phonejacks. It is recommended you write
down your configuration, power off the system, and then complete the physical
connections.
Select from the Phonejack Switch section if you want to re-define the phonejacks. Click
the specific phonejack button for several times to change its input/output functionality.
C.10 Speaker Test
Figure C-11: Audio Configuration
The audio configuration window in Figure C-11 allows you to test each connected
speaker to see if your 4-channel or 6-channel audio operates properly. If any speaker
malfunctions, you should then check the cabling or replace the malfunctioning parts.
Page 224
WSB-9452 PICMG 1.0 CPU Card
Select each specific speaker to test its functionality. The speaker you select will be
highlighted and sound should be generated.
NOTE:
1. The test scenario that appears in the Speaker Test window
corresponds to the number of speakers you selected in the
Sound Effect window.
2. You should select and deselect the Swap Center/Subwoofer
Output check box to see if these two devices properly work.
C.11 S/PDIF-In & S/PDIF-Out
These functions are currently not supported.
Page 225
WSB-9452 PICMG 1.0 CPU Card
C.12 Connector Sensing
Figure C-12: Connector Sensing
Realtek ALC655/883 supports Jack Sensing functionality. If an audio device is plugged
into the wrong connector, a warning message will display informing users to correct the
physical connections.
Click the Start button in Figure C-12 to start the sensing. Please remember to close all
running audio-related programs before executing the sensing operation.
The EZ-Connection screen in Figure C-13 shows the result of sensing test.
Page 226
WSB-9452 PICMG 1.0 CPU Card
Figure C-13: EX Connection
The “Audio Connector” column shows the settings used in the “Speaker Configuration”
window.
The “Current Connection” column shows the types of devices detected during test. If the
result does not match the physical connection, an exclamation mark will appear. (See
Figure C-14)
Page 227
WSB-9452 PICMG 1.0 CPU Card
Figure C-14: Connector Sensing Test Result
After closing the EZ-Connector screen, the following window should appear showing the
latest connection status.
Page 228
WSB-9452 PICMG 1.0 CPU Card
C.13 HRTF Demo
Figure C-15: HRTF Demo
The HRTF window in Figure C-15 allows you to adjust your HRTF (Head Related Transfer
Functions) 3D positional audio before playing 3D applications.
Select a preferred
Environment mode and/or different Sound and Moving Path settings.
C.14 Microphone Effect
This window provides an option, Noise Suppression. Select its check box to enable this
functionality.
Page 229
WSB-9452 PICMG 1.0 CPU Card
C.15 General
The general window in Figure C-16 provides information about this AC’97 audio
configuration utility including Audio Driver version, DirectX version, Audio Controller,
and AC’97 Codec.
You may also change the language of this utility through the
Language pull-down menu.
Figure C-16: General
Page 230
WSB-9452 PICMG 1.0 CPU Card
Appendix
D
D Jmicron RAID Setup
Page 231
WSB-9452 PICMG 1.0 CPU Card
D.1 Introduction
D.1.1 RAID Support
The Jmicron JMB363 chipset integrated controller in WSB-9452S and WSB-9452SDVI
models supports the following RAID configurations on the SATA3 and SATA4 connectors.
JBOD
RAID0
RAID1
D.1.2 What is RAID
RAID, or redundant array of inexpensive disks, is a method of saving data on multiple
disks so that if one of the disks is damaged or destroyed, the data on the disks is not lost.
Only the three RAID levels listed above can be implemented on your system
JBOD stands for Just a Bunch Of Disks. This is not a RAID level. If any thing
happens to one hard drive, all the information on that drive is lost.
RAID0 refers to disk striping. Data is distributed (striped) over multiple disks.
This increases the overall disk performance but the data is not redundantly
stored and therefore any damage to the system disks will result in a loss of
information.
RAID1 refers to disk mirroring. The information on one disk is completely
mirrored onto a second disk. The effective storage capacity of the hard disks
is halved but the data on the disks is safe. If one of the disks is destroyed or
damaged in any way the information on that disk is retrievable from the
second disk.
Page 232
WSB-9452 PICMG 1.0 CPU Card
D.2 RAID Setup
D.2.1 Introduction
To setup the RAID, the following procedures must be completed.
Step 1: Two SATA drives, preferably with the same model and capacity, must be
installed onto the system. Refer to Section 5.4.5.
Step 2: The RAID BIOS must be configured.Step 0:
D.2.2 Install SATA Drives
To implement the on-chip RAID function, two SATA drives must be connected to the
system. Use the SATA drive cables that came with the system to connect the SATA drives.
Refer to Section 5.4.5.
D.2.3 Configure the SATA Controller in BIOS
To configure the RAID BIOS, follow the steps below:
Step 1: Turn on the motherboard and enter the BIOS setup utility. Do this by pressing
DELETE when the system boots up.
Step 2: Select the Advanced Settings menus.
Step 3: Select the IDE Configuration sub-menu.
Step 4: In the IDE Configuration sub-menu, select the ATA/IDE Configuration option.
Make sure it is set to the default setting [Compatible]. Keep the default setting of
the Legacy IDE Channels option [SATA Pri, PATA Sec].
Step 5: Select the Chipset menu.
Step 6: Select the Southbridge sub-menu.
Step 7: Set the SATA Controller Mode Select option to [RAID].
Step 8: Press F10 to save the changes and exit the BIOS setup utility. Step 0:
Page 233
WSB-9452 PICMG 1.0 CPU Card
D.2.4 Configure the RAID BIOS
The next step is to configure the RAID BIOS. To do this, follow the steps below.
Step 1: Restart the system.
Step 2: During POST, the system prompts the user to press <CTRL> and <J> to enter
the RAID Setup Utility (Figure D-1).
Figure D-1: Enter the RAID Setup Utility
Step 3: The main RAID Setup Utility menu opens (Figure D-2). To move from one
window to another, press the Tab key. Below is a brief description of each
window.
Main Menu – This window lists the different actions you can perform in the
RAID Setup Utility.
Hard Disk Drive List – This window lists the SATA disk drives installed and
the following information about the disks:
o
o
o
Model name
Capacity
Type/Status (RAID or non-RAID)
RAID Disk Drive List – This window is empty if no RAID volume is configured.
If a RAID volume is configured, the following information is displayed:
o
o
o
o
o
Page 234
Model name (user-defined RAID volume name)
RAID level
Capacity
Status
Member disks’ corresponding numbers
WSB-9452 PICMG 1.0 CPU Card
Figure D-2: Enter the RAID Setup Utility
D.2.4.1 Create a RAID volume
Step 1: In the RAID Setup Utility main menu, highlight Create RAID Disk Drive (Figure
D-3). Press ENTER.
Figure D-3: Create RAID Disk Drive
Page 235
WSB-9452 PICMG 1.0 CPU Card
Step 2: The Create New RAID window opens. The Name item is highlighted (Figure
D-4). Enter a name made up of one to 16 characters for the RAID volume to be
created, then press ENTER.
Figure D-4: Create RAID Name
Step 3: The Level item is then highlighted (Figure D-5). Press the
or
key to select
the RAID level to create on the SATA drives, then press ENTER. Refer to
Section D.1.1 for supported configurations. Refer to Section D.1.2 for RAID
definitions.
Figure D-5: Set the RAID Level
Page 236
WSB-9452 PICMG 1.0 CPU Card
Step 4: The utility automatically selects the SATA drives installed. The selected disks
are marked with a X (Figure D-6).
Figure D-6: Select disks
Step 5: Set the stripe block size for the RAID 0 set (Figure D-7). This parameter defines
the size of the stripe written to each disk. If RAID 1 or JBOD was configured,
N/A appears after this item. Choose from the following stripe size options:
4KB
8KB
16KB
32KB
64KB
128KB (DEFAULT)
Figure D-7: Set the stripe block size for RAID 0
Page 237
WSB-9452 PICMG 1.0 CPU Card
Step 6: The Size item is then highlighted (Figure D-8). Enter the RAID volume size. The
default value is the maximum volume size allowed.
Figure D-8: Set the RAID volume size
Step 7: After the ENTER key is pressed, the Confirm Creation item is highlighted, and a
confirmation message appears (Figure D-9). Press Y to confirm the creation of
the RAID volume.
Figure D-9: Confirm creation
Page 238
WSB-9452 PICMG 1.0 CPU Card
WARNING:
Pressing Y to confirm creation of the RAID volume destroys all the data
in the SATA drives.
Step 8: Information about the created RAID volume appears in the RAID Disk Drive List
window (Figure D-10).
Figure D-10: RAID Disk Drive List
D.2.4.2 Delete a RAID volume
Step 1: In the RAID Setup Utility main menu, highlight Delete RAID Disk Drive (Figure
D-11). Press ENTER.
Figure D-11: Delete RAID Disk Drive
Page 239
WSB-9452 PICMG 1.0 CPU Card
Step 2: The RAID volume in the RAID Disk Drive List is highlighted (Figure D-12).
Figure D-12: RAID volume
Step 3: Press the space bar to select the RAID volume. The selected RAID volume is
marked with a X. Press the Delete key to delete the RAID volume.
Step 4: A confirmation message appears (Figure D-13). Press Y to confirm the deletion
of the RAID volume. Step 4:
Figure D-13: Delete RAID volume
WARNING:
Pressing Y to confirm deletion of the RAID volume converts the SATA
drives to non-RAID and destroys all the data in the drives.
Page 240
WSB-9452 PICMG 1.0 CPU Card
D.2.4.3 Revert an HDD to Non-RAID
An HDD that had been part of another RAID volume may still be used as a member of the
RAID volume to be created. The HDD must first be reverted to non-RAID. Follow these
steps to revert an HDD to non-RAID.
WARNING:
Reverting an HDD to non-RAID destroys all the data and previous
RAID configurations in the HDD.
Step 5: In the RAID Setup Utility main menu, highlight Revert HDD to Non-RAID
(Figure D-14). Press ENTER.
Figure D-14: Revert HDD to non-RAID
Page 241
WSB-9452 PICMG 1.0 CPU Card
Step 1: Press the
or
key to select the HDD to be reverted to non-RAID, then press
the spacebar to mark the HDD. The selected HDD is marked with a X.
Step 2: A confirmation message appears (Figure D-15). Press Y to confirm the action.
Figure D-15: Confirm revert HDD to non-RAID
Step 3: The reverted HDD is now listed as non-RAID (Figure D-16).
Figure D-16: Reverted HDD
Page 242
WSB-9452 PICMG 1.0 CPU Card
D.2.4.4 Solve Mirror Conflict
A mirror conflict occurs when an HDD in a RAID 1 volume is unplugged from the system,
then plugged in again. The system is unable to identify the source disk from which data
will be mirrored. Use the Solve Mirror Conflict option to set the source disk and rebuild
the mirror drive.
Step 1: In the RAID Setup Utility main menu, highlight Solve Mirror Conflict (Figure
D-17). Press ENTER.
Figure D-17: Solve Mirror Conflict
Step 2: Press the
or
key to select the source disk, then press the spacebar to mark
the HDD. The selected HDD is marked with a X.
Step 3: Press the Tab key to go to the RAID Disk Drive list window.
Step 4: Press the spacebar to mark the RAID volume to be rebuilt.
Step 5: Press ENTER key to begin the rebuild process. A progress bar appears at the
bottom of the screen to indicate the status of the rebuild process. Step 0:
Page 243
WSB-9452 PICMG 1.0 CPU Card
D.2.4.5 Rebuild Mirror Drive
A RAID 1 volume is broken when a member HDD fails. Use the Rebuild Mirror option to
rebuild a RAID 1 volume after the faulty HDD is replaced.
Step 1: In the RAID Setup Utility main menu, highlight Rebuild Mirror Drive (Figure
D-18). Press ENTER.
Figure D-18: Rebuild Mirror Drive
Step 2: Press the
or
key to select the source disk, then press the spacebar to mark
the HDD. The selected HDD is marked with a X.
Step 3: Press the Tab key to go to the RAID Disk Drive list window.
Step 4: Press the spacebar to mark the RAID volume to be rebuilt.
Step 5: Press ENTER to begin the rebuild process. A progress bar appears at the bottom
of the screen to indicate the status of the rebuild process. Step 0:
Page 244
WSB-9452 PICMG 1.0 CPU Card
D.2.4.6 Save and Exit Setup
After the RAID configuration is complete, save the changes and exit the RAID
configuration utility.
Step 1: In the RAID Setup Utility main menu, highlight Save and Exit Setup to effect all
changes made (Figure D-19), then press ENTER.
Figure D-19: Save and Exit Setup
D.2.4.7 Exit without Saving
Step 1: To exit the RAID Setup Utility without saving the changes made, highlight Exit
without Saving (Figure D-20), then press ENTER. Step 0:
Figure D-20: Exit without Saving
Page 245
WSB-9452 PICMG 1.0 CPU Card
D.2.5 Install the OS
Install the OS onto the SATA drives. To do this, follow the steps below.
Step 1: Insert the OS installation CD into the CD drive attached to the IDE device.
Step 2: Restart the system.
Step 3: When prompted, press F6 to install the RAID controller device. Next, press F2 to
continue the installation.
Step 4: A message informs the user the OS is unable to determine the mass storage
device installed on the system. At this point, insert the FDD with the copied
RAID driver files into the FDD drive. The OS accesses the SATA drives through
this disk.
Step 5: Next, select the driver for the OS being installed into the system. Once selected,
press ENTER.
Step 6: The OS and the RAID drivers are then installed into the system. The SATA
drives are configured as RAID drives as stipulated in the above selection.
Step 0:
The OS continues to be installed and the RAID on the SATA drives configured.
Page 246
WSB-9452 PICMG 1.0 CPU Card
Appendix
E
E Hazardous Materials
Disclosure
Page 247
WSB-9452 PICMG 1.0 CPU Card
E.1 Hazardous Material Disclosure Table for IPB Products
Certified as RoHS Compliant Under 2002/95/EC Without Mercury
The details provided in this appendix are to ensure that the product is compliant with the
Peoples Republic of China (China) RoHS standards. The table below acknowledges the
presences of small quantities of certain materials in the product, and is applicable to China
RoHS only.
A label will be placed on each product to indicate the estimated “Environmentally Friendly
Use Period” (EFUP). This is an estimate of the number of years that these substances
would “not leak out or undergo abrupt change.” This product may contain replaceable
sub-assemblies/components which have a shorter EFUP such as batteries and lamps.
These components will be separately marked.
Please refer to the table on the next page.
Page 248
WSB-9452 PICMG 1.0 CPU Card
Part Name
Toxic or Hazardous Substances and Elements
Lead
Mercury
Cadmium
Hexavalent
Polybrominated
Polybrominated
(Pb)
(Hg)
(Cd)
Chromium
Biphenyls
Diphenyl Ethers
(CR(VI))
(PBB)
(PBDE)
Housing
X
O
O
O
O
X
Display
X
O
O
O
O
X
Printed Circuit
X
O
O
O
O
X
Metal Fasteners
X
O
O
O
O
O
Cable Assembly
X
O
O
O
O
X
Fan Assembly
X
O
O
O
O
X
Power Supply
X
O
O
O
O
X
O
O
O
O
O
O
Board
Assemblies
Battery
O:
This toxic or hazardous substance is contained in all of the homogeneous materials for the part is below
the limit requirement in SJ/T11363-2006
X:
This toxic or hazardous substance is contained in at least one of the homogeneous materials for this part
is above the limit requirement in SJ/T11363-2006
Page 249
WSB-9452 PICMG 1.0 CPU Card
此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符
合中国 RoHS 标准规定的限量要求。
本产品上会附有”环境友好使用期限”的标签,此期限是估算这些物质”不会有泄漏或突变”的
年限。本产品可能包含有较短的环境友好使用期限的可替换元件,像是电池或灯管,这些
元件将会单独标示出来。
部件名称
有毒有害物质或元素
铅
汞
镉
六价铬
多溴联苯
多溴二苯醚
(Pb)
(Hg)
(Cd)
(CR(VI))
(PBB)
(PBDE)
壳体
X
O
O
O
O
X
显示
X
O
O
O
O
X
印刷电路板
X
O
O
O
O
X
金属螺帽
X
O
O
O
O
O
电缆组装
X
O
O
O
O
X
风扇组装
X
O
O
O
O
X
电力供应组装
X
O
O
O
O
X
电池
O
O
O
O
O
O
O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
Page 250
WSB-9452 PICMG 1.0 CPU Card
F Index
Page 251
WSB-9452 PICMG 1.0 CPU Card
E
A
AMI BIOS
anti-static precautions
anti-static pad
anti-static wristband
handling
self-grounding
AT power select jumper
location
settings
106
26
26
26
26
26
97
98
98
C
cables
ATA 66/100 flat cable
dual port USB
dual RS-232
SATA drive
SATA drive power
Celeron® M CPU
Chipsets
Intel® 945GM
Intel® ICH7-M
clear CMOS jumper
location
27
28
27
28
28
12
12
12
99
D
Display
DVI
VGA
D-SUB
Page 252
15
15
104
electrostatic discharge
26
External Peripheral InterfaceConnectors
LAN
71
Mini-DIN 6 PS/2
72
USB
73
VGA
74
G
GbE Ethernet
BCM5787
Graphics Support
Intel® GMA 950
18
14
I
IDE 2, 5, 7, 13, 18, 19, 32, 49, 50, 90, 91,
109, 112, 113, 114, 115, 116, 117, 118,
148, 149, 172, 233, 246
Intel® 945GM
6, 12, 14
®
®
2, 10
Intel Celeron D
®
™
Intel Core Duo
2, 3, 6
®
Intel Core™ Solo
2, 3, 6, 10, 11
®
™
Intel Core 2 Duo
2, 3, 6, 10
®
Intel ICH7-M
6, 12, 13, 22
Internal Peripheral Connectors
ATX-12V Power Source
34
Audio Module
36
Backplane to Mainboard Power
37
Battery Connector
39
COM
61
CPU Fan
40
WSB-9452 PICMG 1.0 CPU Card
Digital Input/Output (DIO)
DVI
FDD Connector
Front Panel
IDE
Inverter
IrDA Interface
Keyboard
LVDS
Parallel Port
PCI Express Mini Card
42
43
45
47
49
50
52
53
55
56
58
SATA
TPM
TV Out
USB
63
65
67
69
J
Jmicron JMB363
jumper
AT power select
LCD voltage selection
Jumpers
Clear CMOS
LVDS LCD Voltage Selection
232
97
102
98
100
L
LCD display
voltage select
LCD voltage selection jumper
location
settings
102
102
102
103
102
LVDS voltage selection jumper
location
101
M
Memory support
DDR2
17
P
PCI Express® Mini Card
PICMG 1.0
power supply
AT power select jumper
3, 5
2, 3
97
R
RAID
RJ-45
RoHS
232
72
3
S
SATA II
2, 3, 6, 18, 19, 20, 63, 92
Socket 478 CPU Installation
81
U
unpacking
unpacking checklist
unpacking precautions
26
27
26
W
Watchdog Timer
211
Page 253
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement