DKT Comega | High-power Fiber Amplifier | 6465x_Compact_EDFA_NMGT_Instruction

6465x_Compact_EDFA_NMGT_Instruction
High-power Fiber Amplifier
Network Management Interface
Operation Manual
(ver 1.0)
Table of Contents
Table of Contents.........................................................................................................................1
Revision History ...........................................................................................................................2
Introduction ...................................................................................................................................3
Operation Manual.........................................................................................................................3
1. Web Service ......................................................................................................................3
1.1 HFA Monitor ............................................................................................................3
1.2 Status........................................................................................................................4
1.3 Network ....................................................................................................................5
1.4 DNS ...........................................................................................................................6
1.5 SNMP ........................................................................................................................7
1.6 System......................................................................................................................8
1.7 Password .................................................................................................................9
2. SNMP.................................................................................................................................10
2.1 SNMP Protocol MIB Definition .........................................................................11
2.2 Alarm Trap Definition .........................................................................................12
Page 1 of 14
Revision History
Revision
1.0
Date
20120428
Description
Initial release
Page 2 of 14
Introduction
This type of high power fiber amplifier produced by DKTCOMEGA Networks has been
designed specifically for CATV optical transmission system. The CATV-HFA series
provides up to 33dBm of total optical output power with excellent noise figure performance,
and supports SNMP as well as Web Browser protocol. The available 10/100 Ethernet
Interface enables online configuration of the products and offers customers good
maneuverability.
Operation Manual
1. Web Service
Function: Web Server in HFA Device provides Http operating interface,which allows
customers to read the basic HFA parameters and warning information with Internet
Explorer.
Web Browser default login name: admin
Password: PASS
1.1 HFA Monitor
Input HFA IP address (example: 192.168.1.1) in the address column of the Windows IE
Browser. The following window is displayed (Figure 1, Figure 2):
Click ‘HFA Monitor’ to read the current parameters of HFA
Figure 1
Page 3 of 14
Figure 2
1.2 Status
Click ‘Status’ to read the current parameters of the device such as IP address, MAC
etc(see Figure 3)
Figure 3
Page 4 of 14
1.3 Network
Click ‘Network’ to go to Server setting window, in which parameters like IP Adress, Subnet,
Gateway etc can be set. Click ‘Submit’, new parameters are sent to the server. (see
Figure 4)
Figure 4
There are two configuration table columns displayed. One shows the current running
configuration, and the other shows the configuration that will take effect after the device
is rebooted.
The following items are required for the reboot to take effect:
z
DHCP Client On/Off
z
IP Address
z
Network Mask
z
DHCP Client ID
If the IP Address, Network Mask, Gateway, Hostname, and Domain have been configured
for the device and DHCP is turned on, the original configuration items are ignored.
DHCP will auto-discover and eclipse those configuration items.
Page 5 of 14
1.4 DNS
Click ‘DNS’ to configure DNS of the server. (see Figure 5)
Figure 5
This page displays the current configuration of the DNS subsystem. Users may configure
the Primary and Secondary static server addresses by themselves. If the current
configuration shows the address coming from HCP, the static address will be overrided
until the device is rebooted.
Page 6 of 14
1.5 SNMP
Click ‘SNMP’ to read and write the parameters of HFA via SNMP manager.
(see Figure 6)
Figure 6
Page 7 of 14
1.6 System
Click ‘System’ button to upload new firmware in order to update the current program in this
web page. (see Figure 7). It will take a few minutes to update program, please be patient
for it.
Figure 7
Be careful not to power off or reset the device while uploading new firmware. Once the
upload has completed and the new firmware has been verified and flashed, the device will
be rebooted automatically.
Page 8 of 14
1.7 Password
Click ‘Password’ Button to change user password in this web page. (see Figure 8),
Note that users may start a new browser to access the device if the password of user is
changed successfully.
Figure 8
Page 9 of 14
2. SNMP
Function: read and write the parameters of HFA via SNMP manager.
Default read community: public
Default write community: admin
The SNMP Agent located on the device follows standard SNMPv2 protocol. Users can
read or write the OIDs defined by SNMP protocol mib in the table below.
Page 10 of 14
2.1 SNMP Protocol MIB Definition
No.
OID
Content
R/W Authority
Value Type
HFA Definition
1
1.3.6.1.4.1. 27304.89.2.1
SN
Read Only
String
2
1.3.6.1.4.1. 27304.89.2.2
TYPE
Read Only
String
3
1.3.6.1.4.1. 27304.89.2.3
Working mode
Read Only
String
4
1.3.6.1.4.1. 27304.89.2.4
Input optical power value
Read Only
String
5
1.3.6.1.4.1. 27304.89.2.5
Input optical power los alarm threshold Read & Write
String
6
1.3.6.1.4.1. 27304.89.2.6
Input optical power low alarm threshold Read & Write
String
7
1.3.6.1.4.1. 27304.89.2.7
Input optical power high alarm
threshold
Read & Write
String
8
1.3.6.1.4.1. 27304.89.2.8
Set output optical power
Read & Write
String
9
1.3.6.1.4.1. 27304.89.2.9
Output optical power value
Read Only
String
10
1.3.6.1.4.1. 27304.89.2.10
Output optical power los alarm
threshold
Read &Write
String
11
1.3.6.1.4.1. 27304.89.2.11
Output optical power low alarm
threshold
Read &Write
String
12
1.3.6.1.4.1. 27304.89.2.12
Output optical power high alarm
threshold
Read &Write
String
13
1.3.6.1.4.1. 27304.89.2.13
Case temperature
Read Only
String
14
1.3.6.1.4.1. 27304.89.2.14
Pump1 power
Read Only
String
15
1.3.6.1.4.1. 27304.89.2.15
Pump1 bias current
Read Only
String
16
1.3.6.1.4.1. 27304.89.2.16
Pump1 tec current
Read Only
String
17
1.3.6.1.4.1. 27304.89.2.17
Pump1 temperature
Read Only
String
18
1.3.6.1.4.1. 27304.89.2.18
Pump2 power
Read Only
String
19
1.3.6.1.4.1. 27304.89.2.19
Pump2 bias current
Read Only
String
20
1.3.6.1.4.1. 27304.89.2.20
Pump2 tec current
Read Only
String
21
1.3.6.1.4.1. 27304.89.2.21
Pump2 temperature
Read Only
String
22
1.3.6.1.4.1. 27304.89.2.22
Pump3 power
Read Only
String
23
1.3.6.1.4.1. 27304.89.2.23
Pump3 bias current
Read Only
String
24
1.3.6.1.4.1. 27304.89.2.24
Pump3 tec current
Read Only
String
25
1.3.6.1.4.1. 27304.89.2.25
Pump3 temperature
Read Only
String
26
1.3.6.1.4.1. 27304.89.2.26
Alarm bytes
Read Only
String
27
1.3.6.1.4.1. 27304.89.2.27
Pump on or off switch
Read &Write
String
Note:
1)
Alarm Bytes (OID: 1.3.6.1.4.1. 27304.89.2.26):
Value = ALM1*256*256*256+ ALM2 * 256 * 256 + ALM3 * 256 + ALM4
Example:
ALM1=0x04
ALM2=0 ALM3 = 0x02 ALM4 = 0x00
Value=4*256*256*256+0*256*256+0x02*256+0x00=04000200(HEX)
Page 11 of 14
ALM1&ALM2&ALM3&ALM4 Definition:
ALM1 (1 byte)
Bit
7
6
5
4
3
Description
Los of
Pin high
Pin low
Los of Pout Pout low
2
1
Pout high
Case tmp Case tmp
Pin
high
0
low
ALM2 (1 byte)
Bit
7
6
5
Description
Pump
Pump ild
reserved Pump1
tmp
4
3
2
1
reserved
reserved
reserved Pump2
power
0
power
ALM3 (1 byte)
Bit
7
6
5
Description
reserved reserved
4
3
2
1
0
Power
Power
Fan 1
Fan 2
power
supply 1
supply 2
4
3
2
1
0
reserved
reserved
reserved reserved
reserved Pump3
ALM4 (1 byte)
Bit
7
Description
reserved reserved reserved reserved
Bit value: 1= Alarm
6
5
0= Normal or Reserved
2.2 Alarm Trap Definition
Oid1 (Type)
Oid2 (Current value)
Describe
Trap
Case Temp High Alarm
1.3.6.1.4.1.27304.89.4.1
Case Temp High Recovery
1.3.6.1.4.1.27304.89.4.2
Case Temp Low Alarm
1.3.6.1.4.1.27304.89.4.3
Case Temp Low Recovery
1.3.6.1.4.1.27304.89.4.4
Pin Los Alarm
1.3.6.1.4.1.27304.89.4.5
Pin Los Recovery
1.3.6.1.4.1.27304.89.4.6
Pin High Alarm
1.3.6.1.4.1.27304.89.4.7
1.3.6.1.4.1. 27304.89.2.13 Case temperature High Alarm
(Case Temp.)
Recovery
1.3.6.1.4.1. 27304.89.2.13 Case temperature Low Alarm
(Case Temp.)
Recovery
1.3.6.1.4.1. 27304.89.2.4
Input power Los Alarm
(Input Power)
Recovery
1.3.6.1.4.1. 27304.89.2.4
Input power High Alarm
(Input Power)
Pin High Recovery
1.3.6.1.4.1.27304.89.4.8
Recovery
Page 12 of 14
Pin Low Alarm
1.3.6.1.4.1.27304.89.4.9
Pin Low Recovery
1.3.6.1.4.1.27304.89.4.10
Pout Los Alarm
1.3.6.1.4.1.27304.89.4.11
1.3.6.1.4.1. 27304.89.2.4
Input power Low Alarm
(Input Power)
Recovery
1.3.6.1.4.1. 27304.89.2.9
Output power Los Alarm
(Output Power)
Pout Los Recovery
1.3.6.1.4.1.27304.89.4.12
Pout High Alarm
1.3.6.1.4.1.27304.89.4.13
Pout High Recovery
1.3.6.1.4.1.27304.89.4.14
Pout Low Alarm
1.3.6.1.4.1.27304.89.4.15
Recovery
1.3.6.1.4.1. 27304.89.2.9
Output power High Alarm
(Output Power)
Recovery
1.3.6.1.4.1. 27304.89.2.9
Output power Low Alarm
(Output Power)
Pout Low Recovery
1.3.6.1.4.1.27304.89.4.16
Recovery
Pump temp Alarm
1.3.6.1.4.1.27304.89.4.17
Pump temp Recovery
1.3.6.1.4.1.27304.89.4.18
Pump ild Alarm
1.3.6.1.4.1.27304.89.4.19
Pump ild Alarm
Pump ild Recovery
1.3.6.1.4.1.27304.89.4.20
Recovery
Pump 1 power high Alarm
1.3.6.1.4.1.27304.89.4.21
Pump 1 power high Alarm
1.3.6.1.4.1.27304.89.2.26
(Alarm Bytes)
Pump temperature Alarm
Recovery
Pump 1 power high Recovery 1.3.6.1.4.1.27304.89.4.22
Recovery
Pump 2 power high Alarm
Pump 2 power high Alarm
1.3.6.1.4.1.27304.89.4.23
Pump 2 power high Recovery 1.3.6.1.4.1.27304.89.4.24
Recovery
Pump 3 power high Alarm
Pump 3 power high Alarm
1.3.6.1.4.1.27304.89.4.25
Pump 3 power high Recovery 1.3.6.1.4.1.27304.89.4.26
Recovery
Fan 1 alarm
1.3.6.1.4.1.27304.89.4.27
Fan 1 alarm
Fan 1 alarm recovery
1.3.6.1.4.1.27304.89.4.28
Recovery
Page 13 of 14
Fan 2 alarm
1.3.6.1.4.1.27304.89.4.29
Fan 2 alarm
Fan 2 alarm recovery
1.3.6.1.4.1.27304.89.4.30
Recovery
Power Supply 1 alarm
1.3.6.1.4.1.27304.89.4.31
Power supply 1 alarm
Power Supply 1 alarm
recovery
1.3.6.1.4.1.27304.89.4.32
Recovery
Power Supply 2 alarm
1.3.6.1.4.1.27304.89.4.33
Power supply 2 alarm
Power Supply 2 alarm
recovery
1.3.6.1.4.1.27304.89.4.34
Recovery
(END)
Page 14 of 14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising