Clarity | C4230 | User guide | Clarity C4230 User guide

Clarity C4230 User guide
User Guide
C4230HS Handset
TM
E
N
G
L
I
S
H
BOOST
S
C4230H
MENU
TALK
1
4I
RD/P
3
2
DEF
ABC
5L
8
TUV
PQ
*
6
MNO
JK
GH
7RS
CL/FL
E
S
P
A
Ñ
O
L
0
9
WXYZ
#
F
R
A
N
Ç
A
I
S
CONTENTS
Safety Instructions .......................................................................... 4
Parts Checklist .................................................................................. 7
Operating Instructions .................................................................. 8
Troubleshooting ............................................................................. 10
Technical Specifications .................................................................12
Regulatory Compliance ............................................................... 13
INTRODUCTION
Thank you for purchasing the C4230HS amplified cordless handset
from Clarity. The C4230HS is an additional handset that is compatible
to the C4230 and C4220. In order to use the C4230HS handset, you
must also purchase and pair this handset with either the C4220 or
C4230 telephone.
This User Guide will provide you with the information you need to
use your C4230HS effectively, easily and safely. Please refer to the
C4220 or C4230 User Guide for further information on the
C4230HS handset.
SAFETY INSTRUCTIONS
When using your telephone equipment,
basic safety precautions should always
be followed to reduce the risk of fire,
electric shock and injury to persons
including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the telephone.
3. Do not use this telephone near
a bath tub, wash basin, kitchen
sink or laundry tub, in a wet
basement, near a swimming pool
or anywhere else there is water.
4. Avoid using a telephone (other
than a cordless type) during a
storm. There may be a remote risk
of electrical shock from lightning.
5. Do not use the telephone to report
a gas leak in the vicinity of the leak.
6. Unplug this telephone from the wall
outlets before cleaning. Do not use
liquid cleaners or aerosol cleaners
on the telephone. Use a damp cloth
for cleaning.
7. Place this telephone on a stable
surface. Serious damage and/or
injury may result if the telephone falls.
8. Do not cover the slots and openings on this telephone. This telephone
should never be placed near or over
a radiator or heat register. This telephone should not be placed in a
built-in installation unless proper
ventilation is provided.
9. Operate this telephone using the
electrical voltage as stated on
the base unit or in the owner’s
manual. If you are not sure of the
4
voltage in your home, consult your
dealer or local power company.
10. Do not place anything on the
power cord. Install the telephone
where no one will step or trip on
the cord.
11. Do not overload wall outlets or
extension cords as this can increase
the risk of fire or electrical shock.
12. Never push any objects through
the slots in the telephone. They can
touch dangerous voltage points or
short out parts that could result in
a risk of fire or electrical shock.
Never spill liquid of any kind on
the telephone.
13. To reduce the risk of electrical
shock, do not take this phone apart.
Opening or removing covers may
expose you to dangerous voltages
or other risks. Incorrect reassembly
can cause electric shock when the
appliance is subsequently used.
14. Unplug this product from the wall
outlet and refer servicing to the
manufacturer under the following
conditions:
A. When the power supply cord
or plug is frayed or damaged.
B. If liquid has been spilled into
the product.
C. If the telephone has been
exposed to rain or water.
D. If the telephone does not
operate normally by following
the operating instructions.
Adjust only those controls that
are covered by the operating
SAVE THESE INSTRUCTIONS
SAFETY INSTRUCTIONS
instructions. Improper adjustment may require extensive
work by a qualified technician
to restore the telephone to
normal operation.
E. If the telephone has been
dropped or the case has
been damaged.
F.
If the telephone exhibits a
distinct change in performance.
required before your hearing could be
affected. If you experience hearing discomfort, you should stop using the
handset. To protect your hearing, some
hearing experts suggest that you:
1. Set the volume control in a low
position and then adjust the
volume to a comfortable level.
2. Limit the amount of time you use
the handset at high volume.
15. Never install telephone wiring
during a lightning storm.
3. Avoid turning up the volume to
block out noisy surroundings.
16. Never install telephone jacks in wet
locations unless the jack is specifically designed for wet locations.
CHILDREN: Never allow children to
play with the product – small parts may
be a choking hazard and the amplified
volume may cause hearing damage.
17. Never touch uninsulated telephone
wires or terminals unless the telephone line has been disconnected
at the network interface.
18. Use caution when installing or
modifying telephone lines.
19. Use only the power cord and
batteries indicated in the manual.
Do not dispose of batteries in a
fire. They may explode. Check with
local codes for possible special
disposal instructions.
20. Plug the AC adaptor into the outlet
that is nearest and most accessible
to the telephone.
SAFETY INSTRUCTIONS
FOR BATTERIES
Caution: Risk of explosion if battery
is replaced by an incorrect type.
Dispose of used batteries according
to the instructions.
1. Use only the approved battery
pack in the handset of your
cordless phone.
For Handset Unit:
3.6V 800mAh Ni-MH AAA
GPI International Ltd.:
GP80AAAH3BXZ
Exposure to high volume sound levels
2. Do not dispose of the battery in a
may damage your hearing. Although there
fire as it may explode. Check with
is no single volume setting that is approlocal codes for possible special
disposal instructions.
priate for everyone, you should always
use the handset with the volume set at
3. Do not open or mutilate the battery.
moderate levels and avoid prolonged
Released electrolyte is corrosive and
exposure to high volume sound levels.
may cause damage to the eyes and
The louder the volume, the less time is
skin. It may be toxic if swallowed.
SAVE THESE INSTRUCTIONS
5
SAFETY INSTRUCTIONS
4. Exercise care in handling batteries
in order not to short the battery
with conducting materials such as
rings, bracelets and keys. The battery
or conduction material may overheat and cause burns.
5. Charge the battery (ies) provided
with or identified for use with this
product only in accordance with the
instructions and limitations specified
in this manual.
6. Observe proper polarity orientation between the battery pack
and the battery charger.
Pacemaker Warning
If you or a member of your
household has a pacemaker or
other medical devices, consult your
physician or the manufacturer of the
pacemaker or medical device before
using this product. The product
should be used in accordance with
the guidelines provided by your
physician or the manufacturer of
the pacemaker or medical device.
6
SAVE THESE INSTRUCTIONS
CONTENTS & PARTS CHECKLIST
1. Charger Base
1.
2.
3.
4.
5.
6.
7.
Charger Base
Handset
Battery pack
Battery compartment cover
Belt clip
AC adapter
User Guide
BOOST
TALK
ME NU
CL/FL
RD/P
1
2
3
DEF
ABC
4
5
GHI
6
JKL
MNO
7
8
PQRS
TUV
*
0
9
WXYZ
3. Battery pack
#
TONE
CONTROL
TONE
2. Handset
4. Battery
compartment
cover
INTERCOM
5. Belt clip
6. AC adapter
7. User Guide
7
Operating Instructions
C4230HS
HOW TO CONNECT THE C4230HS CHARGING BASE
Charge LED – LED will light up
when handset is in base charging.
Connect the AC adapter
to the back of the charging
base and a 120V wall outlet
as shown above.
120V outlet
HEAD
SET
AC adapter
STOP
Handset battery must
charge 12 hours before use.
TONE
INTERCOM
Battery
• Insert battery pack such that (+) and (-)
on battery touch spring in battery
compartment.
• Place handset on base to charge.
• Make sure the charge LED on base
is illuminated.
Registering
The C4230HS is compatible to the C4220 and the
C4230. In order to use the C4230HS you must
register it to a C4220 or C4230.
To register the C4230HS, place the C4230HS handset
into the main unit until the screen displays: Handset
Registered. It will take approximately 5-10 seconds
for the handset to register to the base.
After registering the C4230HS, the handset will
automatically be assigned a handset number.
8
12:09 AM 04/06
Handset Registered
Exit
Save
C4230HS
Operating Instructions
HOW TO DIAL OR RECEIVE A CALL
1. Complete connection instructions as
shown in this guide.
1
BOOST
2. Install and charge battery as shown
on page 8.
2
3
3. Make sure the power LED is on at bottom
of base.
M EN U
CL/FL
RD/P
1
2
3
ABC
4
5. When placing a call press TALK and then
dial the number.
7
O
8
TUV
1 Volume Control
The dial controls the volume level of
the handset, headset or neckloop.
HEA
6
MN
JKL
PQRS
*
DEF
5
GHI
6. After completing the call press TALK again
and return handset to base unit.
0
9
WXYZ
#
DSET
5
M
NEC KLO
INTE RCO
6
OP
RINGER
ON/OFF
TON E
2 Boost
When pressed, an extra level of
amplification is added over the entire
range of volume control. (Digital
Clarity® PowerTM Technology)
TALK
4
4. To receive a call pick up handset from base
and press TALK to answer incoming call.
3 Speaker
Press to activate handset speakerphone.
Press again to switch back to earpiece.
4 Talk
Press TALK button and dial number to
make a call. To end call press TALK again.
5 Tone
The C4230HS has four (4) AUDIO
TONE settings. Pressing the TONE
button changes the style of amplification and allows you to customize
your hearing experience.
Hearing loss is specific to each
individual; therefore, we suggest
exploring each setting to find the
one you find most comfortable.
(see main User Guide for a complete
description of available audio profiles)
6 Ringer On/Off
Switch to turn Handset Ringer
On or Off.
Additional information can be found in the C4220 or C4230 User Guide.
9
TROUBLESHOOTING
The unit will not operate/no dial tone:
• Verify the AC Adapter is securely plugged into AC outlet, the
base and the telephone.
• Verify the telephone line cord is securely plugged into the wall
jack and the telephone.
• Make sure the battery has been placed in the battery compartment correctly. (The circular metal contacts on battery need
to touch the metal springs inside battery compartment.)
• Make sure the handset battery is fully charged.
• Verify the telephone is in the correct dialing mode tone (touch)
or pulse (rotary).
• Make sure you are in the usable range of the base station.
The phone does not ring when you receive a call:
• Make sure the RINGER switch on the handset is set to ON.
• Verify the AC Adapter is securely plugged into the AC outlet,
and the base.
• Verify the telephone line cord is securely plugged into the
wall jack and the telephone.
• Make sure you are within the usable range of the base station.
• You may have too many extensions on your line. Try unplugging
a few devices.
Noise, Static, Interference or Other Calls Heard while
Using the Handset:
• Make sure you are within the usable range of the base station.
• Make sure the handset battery is fully charged.
• Try relocating the base unit to another location.
• Make sure the AC Adapter is not plugged into the wall outlet
with other appliances.
10
TROUBLESHOOTING
Phone Will Not Hold Charge:
• Make sure the charging contacts on the handset and base
are free of dust and dirt. While unplugged, clean the contacts
with a soft cloth.
• Make sure CHARGE LED on the base is lit when the handset
is in the cradle.
• Handset battery may have developed a memory, due to user
improperly charging, and may need to be replaced. (Battery
must be charged a full 12 hours before the first use.)
Difficulty in Placing or Receiving Calls:
• Move closer to the base and try again.
• Make sure you have selected the correct dialing mode, tone
or pulse.
• Make sure the AC Adapter is not plugged into a wall outlet
with other appliances. Disconnect for 5-10 seconds then
reconnect. Place the handset back on the base and reinsert
the AC Adapter.
• Make sure the handset battery is fully charged.
Your handset screen is showing Out of Range
• Move closer to the base.
• To register the C4230HS, place the C4230HS handset into the
main unit until the screen displays: Handset Registered. It will
take approximately 5-10 seconds for the handset to register
to the base.
• Handset may need to be re-registered to the base manually.
First, select INITIAL SETUP on the main menu. Second, select
REGISTRATION on the sub-menu. The screen will then display
“Please hold the page button until beep.” This will register your
handset to the base. The screen will then display the
handset number.
11
TECHNICAL SPECIFICATIONS
General
Model Number:
Frequency:
Amplification:
Compatibility:
C4230HS
5.8 GHz
50 dB
C4230 and C4220
Handset Unit
Product in Inches:
Weight in Pounds:
(L x W x H): 7.25 x 2 x 1.25
0.5 lb
Base
Product in Inches:
Weight in Pounds:
Power Supply:
(L x W x H): 3.50 x 2.75 x 2
.50 lb
AC Adaptor (Input: 120V AC, 60 Hz;
Output: 9V DC, 500mA)
Handset and Base
Product in Inches
(L x W x H): 8 x 3.25x3.25
Weight in Pounds:
1.10 lbs
Battery Information
Battery Type:
Ni-MH AAA 800 mAh 3.6V
Battery Life Talk Time: 3-4 Hours
Battery Life Standby: 6 days
Contact Clarity customer service for information on
purchasing additional handsets or replacement battery.
Clarity Contact information
Customer Service:
1-800-426-3738
Address:
4289 Bonny Oaks Drive, Suite 106
Chattanooga, TN 37406
12
REGULATORY COMPLIANCE
Part 68 of FCC Rules
Information
a) This equipment complies with Part
68 of the FCC rules and the requirements adopted by the ACTA. On the
bottom of this equipment is a label that
contains, among other information,
a product identifier in the format
US:AAAEQ##TXXXX. If requested,
this number must be provided to the
telephone company.
b) A plug and jack used to connect this
equipment to the premises wiring and
telephone network must comply with
the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A
compliant telephone cord and modular
plug, RJ11CUSOC, is provided with this
product. It is designed to be connected
to a compatible modular jack that is
also compliant. See installation instructions for details.
c) The REN is used to determine the
number of devices that may be connected to a telephone line. Excessive
RENs on a telephone line may result in
the devices not ringing in response to
an incoming call. In most but not all
areas, the sum of RENs should not
exceed five (5.0). To be certain of the
number of devices that may be connected to a line, as determined by the
total RENs, contact the local telephone
company. For products approved after
July 23, 2001, the REN for this product
is part of the product identifier that has
the format US: AAAEQ##TXXXX.
The digits represented by ## are the
REN without a decimal point (e.g., 03 is
a REN of 0.3). For earlier products, the
REN is separately shown on the label.
d) If this telephone equipment causes
harm to the telephone network, the
telephone company will notify you in
advance that temporary discontinuance of service may be required. But
if advance notice isn’t practical, the
telephone company will notify the
customer as soon as possible. Also,
you will be advised of your right to
file acomplaint with the FCC if you
believe it is necessary.
e) The telephone company may make
changes in its facilities, equipment,
operations or procedures that could
affect the operation of the equipment.
If this happens the telephone company
will provide advance notice in order for
you to make necessary modifications
to maintain uninterrupted service.
f) If trouble is experienced with this
telephone equipment, for repair or
warranty information, please contact
Clarity, 1-800-552-3368. If the equipment is causing harm to the telephone
network, the telephone company may
request that you disconnect the equipment until the problem is resolved.
g) This telephone equipment is not
intended to be repaired and it contains
no repairable parts. Opening the
equipment or any attempt to perform
repairs will oid the warranty. For
service or repairs, call 1-800-552-3368.
h) Connection to party line service
is subject to state tariffs. Contact the
state public utility commission, public
service commission or corporation
commission for information.
i) If your home has specially wired
alarm equipment connected to the
telephone line, ensure the installation
13
REGULATORY COMPLIANCE
of this telephone equipment does not
disable your alarm equipment. If you
have questions about what will disable
alarm equipment, consult your telephone company or a qualified installer.
j) This telephone equipment is hearing
aid compatible.
Customer-Owned Coin/Credit
Card Phones:
To comply with state tariffs, the telephone company must be given notification prior to connection. In some states,
the state public utility commission, public service commission or corporation
commission must give prior approval
of connection.
Part 15 of FCC Rules
Information
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Your equipment has been tested and
found to comply with the limits of a
Class B digital device, pursuant to
Part 15 of FCC rules. These limits are
designed to provide reasonable protection against harmful interference in
residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular installation; if this equipment does
cause harmful interference to radio or
television reception, which can be
14
determined by turning the equipment
off and on, you are encouraged to try
to correct the interference by one of
the following measures:
1. Where it can be done safely,
reorient the receiving television
or radio antenna.
2. To the extent possible, relocate
the television, radio or other
receiver with respect to the telephone equipment. (This increases
the separation between the telephone equipment and the receiver.)
3. Connect the telephone equipment
into an outlet on a circuit different
from that to which the television,
radio, or other receiver is
connected.
4. Consult the dealer or an experenced Radio/TV Technician for help.
CAUTION: Changes or modifications to this equipment not
expressly approved by the party
responsible for compliance could
void the user’s authority to operate
the equipment.
Privacy of communications may not be
ensured when using this phone.
CAUTION: To maintain the
compliance with the FCC’s RF exposure guideline, place the base unit at
least 20 cm from nearby persons.
For body worn operation, this handset
has been tested and meets the FCC
RF exposure guidelines when used
with the (Plantronics) accessories
supplied or designated for this product.
Use of other accessories may not
ensure compliance with FCC RF exposure guidelines.
REGULATORY COMPLIANCE
Industry Canada Technical
Specifications
This product meets the
applicable Industry Canada
technical specifications.
Before installing this equipment, users
should ensure that it is permissible
to be connected to the facilities of
the local telecommunications company.
The equipment must also be installed
using an acceptable method of connection. In some cases, the company’s inside
wiring associated with a single line
individual service may be extended by
means of a certified connector
assembly (telephone extension cord).
The customer should be aware that
compliance with the above conditions
may not prevent degradation of service
in some situations. Repairs to certified
equipment should be made by an
authorized Canadian maintenance
facility designated by the supplier.
Any repairs or alterations made by the
user to this equipment, or equipment
malfunctions, may give the telecommunications company cause to request the
user to disconnect the equipment.
Users should ensure for their own
protection that the electrical ground
connections of the power utility,
telephone lines and internal metallic
water pipe system, if present, are
connected together. This precaution
may be particularly important in
rural areas.
CAUTION: Users should not
attempt to make such connections
themselves, but should contact the
appropriate electrical inspection
authority, or electrician, as appropriate.
The Ringer Equivalence Number is an
indication of the maximum number
of terminals allowed to be connected
to a telephone interface. The termination on an interface may consist of any
combination of devices subject only to
the requirement that the sum of the
Ringer Equivalence Numbers of all the
devices does not exceed five.
(The term “IC:” before the certification/registration number only signifies
that the Industry Canada technical
specifications were met.)
This Class B digital apparatus complies
with Canadian ICES-003.
The party responsible for
regulatory compliance:
Clarity, a Division of Plantronics, Inc.
4289 Bonny Oaks Drive, Suite 106
Chattanooga, TN 37406
Phone: 1-800-552-3368
15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising