Chauvet Quad-9 User manual

Chauvet Quad-9 User manual
User Manual
Edition Notes
Edition Notes
This User Manual covers the description, safety precautions, installation, programming,
operation, and maintenance of the COLORado™ Batten Quad-9 Tour.
CHAUVET® released this edition of the COLORado™ Batten Quad-9 Tour User Manual
in November 2013.
Trademarks CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or
Chauvet). The CHAUVET® logo in its entirety including the CHAUVET® name and the
dotted triangle, and all other trademarks in this manual pertaining to services, products,
or marketing statements (example: It’s Green Thinking™) are owned or licensed by
CHAUVET®. Any other product names, logos, brands, company names, and other
trademarks featured or referred to within this document are the property of their
respective trademark holders.
Copyright Notice CHAUVET® owns the content of this User Manual in its entirety, including but not limited
to pictures, logos, trademarks, and resources.
© Copyright 2013 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
Manual Use CHAUVET® authorizes its customers to download and print this manual for professional
information purposes only. CHAUVET® expressly prohibits the usage, copy, storage,
distribution, modification, or printing of this manual or its content for any other purpose
without written consent from CHAUVET®.
Document Printing For better results, print this document in color, on letter size paper (8.5 x 11 in), doublesided. If using A4 paper (210 x 297 mm), configure your printer to scale the content
accordingly.
Intended Audience Any person in charge of installing, operating, and/or maintaining this product should
completely read through the guide that shipped with the product, as well as this manual,
before installing, operating, or maintaining this product.
Disclaimer CHAUVET® believes that the information contained in this manual is accurate in all
respects. However, CHAUVET® assumes no responsibility for any errors or omissions
in this document. CHAUVET® reserves the right to revise and make changes to the
content of this document without obligation that CHAUVET® notify any person or
company of such revision or changes. This does not in any way constitute a
commitment by CHAUVET® to make such changes. CHAUVET® may issue a revision
of this manual or a new edition to incorporate such changes.
Author
A. Leon
Date
11/21/13
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Editor
D. Couppe
Date
11/21/13
Table of Contents
Table of Contents
1. Before You Begin ...................................................................................................................................... 1
What is Included ........................................................................................................................................................... 1
Claims .......................................................................................................................................................................................... 1
Manual Conventions .................................................................................................................................................................... 1
Symbols ....................................................................................................................................................................................... 1
Safety Notes ................................................................................................................................................................. 2
Personal Safety ............................................................................................................................................................................ 2
Mounting and Rigging .................................................................................................................................................................. 2
Power and Wiring ......................................................................................................................................................................... 2
Operation ..................................................................................................................................................................................... 2
Expected LED Lifespan ................................................................................................................................................ 2
2. Introduction ............................................................................................................................................... 3
Description .................................................................................................................................................................... 3
Features ........................................................................................................................................................................ 3
Overview ....................................................................................................................................................................... 4
Dimensions ................................................................................................................................................................... 5
3. Setup .......................................................................................................................................................... 6
AC Power ...................................................................................................................................................................... 6
AC Plug ........................................................................................................................................................................................ 6
Fuse Replacement ....................................................................................................................................................................... 6
Power Linking............................................................................................................................................................................... 7
DMX Linking.................................................................................................................................................................. 7
DMX Modes ................................................................................................................................................................................. 7
Master/Slave Connectivity............................................................................................................................................................ 7
Mounting ....................................................................................................................................................................... 8
Orientation ................................................................................................................................................................................... 8
Rigging ......................................................................................................................................................................................... 8
4. Operation ................................................................................................................................................... 9
Control Panel Description ............................................................................................................................................. 9
Control Options ............................................................................................................................................................. 9
Programming ................................................................................................................................................................ 9
DMX Personality .......................................................................................................................................................................... 9
DMX Control................................................................................................................................................................................. 9
Loss of Signal Setting ................................................................................................................................................................ 10
Static Color ................................................................................................................................................................................ 10
Auto Programs ........................................................................................................................................................................... 10
Edit Custom Programs .............................................................................................................................................................. 10
Strobe Personality ...................................................................................................................................................................... 10
Master/Slave .............................................................................................................................................................................. 11
Color Settings............................................................................................................................................................................. 11
Dimmer Curves .......................................................................................................................................................................... 11
Curve Settings............................................................................................................................................................................ 12
Control Panel Lock ..................................................................................................................................................................... 12
Passcode ................................................................................................................................................................................... 12
Settings Lock.............................................................................................................................................................................. 12
Program Upload ......................................................................................................................................................................... 13
Resetting Factory Defaults ......................................................................................................................................................... 13
Resetting Calibration Defaults .................................................................................................................................................... 14
Setting the .................................................................................................................................................................................. 14
White Color ................................................................................................................................................................................ 14
Calibrating the ............................................................................................................................................................................ 14
White Color ................................................................................................................................................................................ 14
TOUR Notes ............................................................................................................................................................... 15
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
-i-
Table of Contents
Master Dimmer........................................................................................................................................................................... 15
Red, Green, Blue, and White Color Selection ............................................................................................................................ 15
Color Macros .............................................................................................................................................................................. 15
Strobe ........................................................................................................................................................................................ 15
Auto/Custom Programs .............................................................................................................................................................. 15
Dimmer Speed ........................................................................................................................................................................... 15
Menu Map ................................................................................................................................................................... 16
DMX Values ................................................................................................................................................................ 18
5. Technical Information ............................................................................................................................. 26
Product Maintenance .................................................................................................................................................. 26
Returns ....................................................................................................................................................................... 26
Technical Specifications ............................................................................................................................................. 27
Contact Us .................................................................................................................................................................. 28
-ii-
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Before You Begin
1. Before You Begin
What is Included
·
COLORado™ Batten Quad-9 Tour
·
Neutrik® powerCON® power cord
·
Safety Cable
·
Warranty Card
·
Quick Reference Guide
Claims Carefully unpack the product immediately and check the box to make sure all the parts
are in the package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from
shipping or show signs of mishandling, notify the carrier immediately, not CHAUVET®.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with CHAUVET® within 7 days of delivery.
Manual Conventions
Convention
1–512
50/60
<SET>
Settings
MENU>Settings
1–10
Yes/No
ON
Symbols
Meaning
A range of values in the text
A set of mutually exclusive values in the text
A button on the product’s control panel
A product function or a menu option
A sequence of menu options
A range of menu values from which to choose in a menu
A set of two mutually exclusive menu options in a menu
A unique value to be entered or selected in a menu
Symbols
Meaning
Critical installation, configuration, or operation information.
Failure to comply with this information may cause the product not
to work, damage third-party equipment, or cause harm to the
operator.
Important installation or configuration information. Failure to
comply with this information may keep the product from working.
Useful information.
The term “DMX” used throughout this manual refers to the USITT DMX512-A digital data
transmission protocol.
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
-1-
Before You Begin
Safety Notes
Read all the following Safety Notes before working with this product. These notes
include important information about the installation, usage, and maintenance of this
product.
This product contains no user-serviceable parts. Any reference to servicing in
this User Manual will only apply to properly trained CHAUVET® certified
technicians. Do not open the housing or attempt any repairs.
All applicable local codes and regulations apply to proper installation of this
product.
Personal Safety
Mounting and
Rigging
Power and Wiring
Operation
·
Avoid direct eye exposure to the light source while the product is on.
·
Always disconnect this product from power before servicing.
·
Always connect this product to a grounded circuit to avoid the risk of electrocution.
·
Do not touch this product’s housing when operating because it may be hot.
·
This product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose this product to rain or moisture.
·
Make sure there are no flammable materials close to this product while it is
operating.
·
When hanging this product, always secure to a fastening device using a safety
cable (included).
·
Always make sure you are connecting this product to the proper voltage in
accordance with the specifications in this manual or on the product’s specification
label.
·
Never connect this product to a dimmer pack or rheostat.
·
Never disconnect this product by pulling or tugging on the power cable.
·
Do not operate this product if you see damage on the housing, lenses, or cables.
Have the damaged parts replaced by an authorized technician at once.
·
Do not cover the ventilation slots when operating to avoid internal overheating.
·
The maximum ambient temperature is 113 °F (45 °C). Do not operate this product
at a higher temperature.
·
In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your CHAUVET® product may require service, contact
CHAUVET® Technical Support.
Expected LED
Lifespan
-2-
LEDs gradually decline in brightness over time, mostly because of heat. Packaged in
clusters, LEDs exhibit higher operating temperatures than in ideal, single-LED
conditions. For this reason, using clustered LEDs at their fullest intensity significantly
reduces the LEDs’ lifespan. Under normal conditions, this lifespan can be 40,000 to
50,000 hours. If extending this lifespan is vital, lower the operating temperature by
improving the ventilation around the product and reducing the ambient temperature to
an optimal operating range. In addition, limiting the overall projection intensity may also
help to extend the LEDs’ lifespan.
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Introduction
2. Introduction
Description
Features
The COLORado™ Batten Quad-9 Tour offers simple and complex DMX channel profiles
for programming versatility. Flicker-free electronic dimming is possible through 16-bit
dimming of individual colors as well as the master dimmer. Control options include
manual RGBW color mixing, custom auto programs, and DMX.
·
DMX Channels: 3, 4, 5, 6, 9, 11, 16, 27 or 36
·
Operation modes:
·
·
·
·
·
·
·
·
3-channel (ARC.1): RGB control
3-channel (HSV): color hue, saturation, and value control
4-channel (AR1.D): RGB and dimmer control
4-channel (ARC.2): RGBW control
5-channel (AR2.D): RGBW and dimmer control
6-channel (AR2.S): RGBW, classic strobe and dimmer control
9-channel (HALO): Dimmer control with pixel selection, 2700 K
11-channel (TOUR): RGBW, pixel selection, dimmer, color macro, white
balance, strobe (special and classic), programs (auto and custom),
auto speed, and dimmer speed control
· 16-channel (TR16): 16-bit RGBW and dimmer, pixel selection, color macro,
white balance, strobe (special and classic), programs (auto and custom),
dimmer speed control
· 27-channel (PIX1): RGB control with pixel selection
· 36-channel (PIX2): RGBW control with pixel selection
·
16-bit dimming of individual colors as well as the master dimmer
·
RGBW quad-color LEDs
·
Electronic dimming
·
Controller-free RGBW color mixing
·
Recall custom auto programs via DMX
·
Five distinct dimming curves
·
LED display with passcode protection
·
3- and 5-pin XLR data input and output connectors
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
-3-
Introduction
Overview
Front View
Quad-color LED
Side View
Mounting
Bracket
3- and 5-pin
DMX In
Display and
Control Panel
Fan
Power In
Bottom View
Power Out
Safety Loop
Fuse Holder
3- and 5-pin
DMX Out
-4-
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Introduction
Dimensions
38 in
975 mm
7.5 in
190 mm
7.8 in
200 mm
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
-5-
Setup
3. Setup
AC Power
The COLORado™ Batten Quad-9 Tour has an auto-ranging power supply that works
with an input voltage range of 100~240 VAC, 50/60 Hz. To determine the power
requirements for each COLORado™ Batten Quad-9 Tour, refer to the label affixed to the
product. You can also refer to the Technical Specifications section in this manual.
The listed current rating indicates the maximum current draw during normal operation.
For more information, you may download Sizing Circuit Breakers from the CHAUVET®
website: www.chauvetpro.com.
Always connect this product to a protected circuit with an appropriate electrical
ground to avoid the risk of electrocution or fire.
Never connect this product to a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
AC Plug The COLORado™ Batten Quad-9 comes with a power input cord terminated with a
Neutrik® powerCON® connector on one end and an Edison plug on the other end (U.S.
market). If the power input cord that came with your product has no plug, or if you need
to change the Edison plug, use the table below to wire the new plug.
Connection
Wire (U.S.)
Wire (Europe)
Screw Color
AC Live
Black
Brown
Yellow or Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
Fuse Replacement
Make sure to disconnect the product’s power cord before replacing a blown fuse.
Always replace the blown fuse with another of the same type and rating.
1. Disconnect this product from the power outlet.
2. Using a #2 Phillips screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse and replace with another fuse of the same type and rating
(T 3.15 A, 250 V).
4. Screw the fuse holder cap back in place and reconnect power.
-6-
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Setup
Power Linking The COLORado™ Batten Quad-9 supports power linking. You can power link up to
9 products at 120 V, 14 products at 208 V, or 15 products at 230 V.
This product comes with a power input cord. This product does not come with a power
linking cable; however, a power linking cable is available as an option.
DMX Linking
You can link the COLORado™ Batten Quad-9 Tour to a DMX controller using a standard
DMX serial connection. If using other DMX compatible products with the COLORado™
Batten Quad-9 Tour, you can control each individually with a single DMX controller.
DMX Modes The COLORado™ Batten Quad-9 Tour uses the standard DMX data connection for its
TOUR, TR16, ARC.1, AR1.D, ARC.2, AR2.D, AR2.S, HSV, PIX1, PIX2, and HALO
DMX modes.
·
Refer to the Introduction section for a brief description of these modes.
·
Refer to the Operation section to learn how to configure the COLORado™ Batten
Quad-9 Tour to work in these modes.
·
The DMX Values section provides you with detailed information regarding the
DMX modes.
Master/Slave The Master/Slave mode allows a COLORado™ Batten Quad-9 Tour (the “master”) to
Connectivity control one or more products (the “slaves”) without a DMX controller.
One COLORado™ Batten Quad-9 Tour becomes the master product either when
running in static (STAT) mode or when using the automatic (AT) or customizable (PR)
programs.
In addition, you must configure each of the slaves (via their control panels) to operate in
Slave (SLAV) mode. During Master/Slave operation, the slaves will operate in unison
with the master.
For more information, see the Menu Map section.
Do not connect a DMX controller to products operating in Master/Slave mode. The
DMX controller signals may interfere with the signals from the master product.
·
The Operation section of this manual provides detailed instructions on how to
configure the Master and Slave products.
·
If you need more information about DMX standards, Master/Slave connectivity, or
the DMX cables needed in order to link the product to a DMX controller, download
the DMX Primer from the CHAUVET® website: www.chauvetpro.com.
·
Verify the DIMX and CURV settings are set to OFF for optimal control of the TR16
personality. For more information, see Menu Map.
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
-7-
Setup
Mounting
Before mounting this product, read and follow the Safety Notes in this manual.
Orientation Always mount this product in a safe position and make sure there is adequate room for
ventilation, configuration, and maintenance.
Rigging The COLORado™ Batten Quad-9 Tour comes with two adjustable feet that double as
hanging brackets to which you can attach mounting clamps. CHAUVET® recommends
using the following general guidelines when mounting this product.
Procedure
·
When selecting an installation location, consider easy access to this product for
operation, programming adjustments, and routine maintenance.
·
Make sure to mount this product away from any flammable material as indicated in
the Safety Notes.
·
Never mount in places where rain, high humidity, extreme temperature changes, or
restricted ventilation may affect the product.
·
If hanging this product, make sure that the mounting location can support the
product’s weight. Refer to the Technical Specifications for the weight-bearing
requirements of this product.
·
When hanging this product, always secure to a fastening device using a safety cable
(included).
The COLORado™ Batten Quad-9 Tour comes with two adjustable feet that double as
hanging bracket to which you can attach clamps. These brackets also serve as floor
stands or wall-mount supports. You must supply your own clamps and make sure the
clamps are capable of supporting the weight of this product. You must use two mounting
points per product.
Safety Cable
Mounting Clamps
(such as CH-05
from CHAUVET®
Mounting Diagram
(such as CLP-15 or
CLP-15N from
CHAUVET®
Overhead Mounting
Floor Mounting
-8-
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Operation
4. Operation
Control Panel
Description
Button
<MENU>
<ENTER>
<UP>
<DOWN>
Function
Exits from the current menu or function
Enables the currently displayed menu or sets the currently
selected value in to the current function
Navigates upward through the menu options and increases the
numeric value when in a function
Navigates downward through the menu options and decreases
the numeric value when in a function
Control Options
You can set the COLORado™ Batten Quad-9 Tour starting address in the 001 to 512
DMX range. This enables control of up to 14 products in the 36-channel PIX2
personality.
Programming
Refer to the Menu Map to understand the menu options. The menu map shows the main
level and a variable number of programming levels for each option.
·
To go to the desired main level, press <MENU> repeatedly until the option shows on
the display. Press <ENTER> to select. This will take you to the first programming
level for that option.
·
To select an option or value within the current programming level, press <UP> or
<DOWN> until the option shows on the display. Press <ENTER> to select. In this
case, if there is another programming level, you will see that first option, or you will
see the selected value.
·
Press <MENU> repeatedly to exit to the previous main level.
DMX Personality This setting allows you to choose a particular DMX personality.
1. Go to the PERS main level.
2. Select the desired personality (TOUR, TR16, ARC.1, AR1.D, ARC.2, AR2.D,
AR2.S, HSV, PIX1, PIX2, or HALO).
For the highest starting address you can select for each personality, see the DMX
Values section. Verify that the starting addresses on the products do not overlap due to
the new personality setting.
DMX Control In this mode, each product will respond to a unique starting address from the DMX
controller. All products with the same starting address will respond in unison.
1. Select a DMX personality as shown in DMX Personality.
2. Set the running mode:
a. Go to the RUN main level.
b. Select the DMX programming level.
3. Set the starting address:
a. Go to ADDR main level.
b. Select the starting address (D.001–512).
The highest recommended starting address for each DMX mode are as follows:
DMX Mode
TOUR
ARC.1
AR1.D
PIX2
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
DMX Address
502
510
509
477
DMX Mode
ARC.2
AR2.D
AR2.S
HALO
DMX Address
509
508
507
504
DMX Mode
HSV
TR16
PIX1
DMX Address
510
497
486
-9-
Operation
Loss of Signal Setting This setting controls how the product will respond when the DMX signal is lost.
1. Go to the SET main level, and select DERR.
a. Select SAVE to make the product use the last command used when the signal
is lost.
b. Select BLAK to turn off the all the LEDs when the signal is lost.
Static Color The Static Color mode allows for RGBW color mixing without a DMX controller.
1.
2.
3.
4.
5.
6.
Go to the STAT main level.
Select the desired color RED (red), GREN (green), BLUE (blue), or WHIT (white).
Select the desired color value (000–255).
Repeat the steps for each color.
Select STRB.
Select the desired frequency 00–20 (0–20 Hz).
Auto Programs Auto programs allow for dynamic RGBW color mixing without a DMX controller.
1. Go to AUTO.
2. Select the desired auto (AT. 01–10) or custom program (PR. 01–10).
3. Select the desired speed at which the chosen program will run (P. 000–255).
You cannot edit any of the auto programs (AT.01–10); however, you can edit the custom
programs (PR.01–10). See Edit Custom Programs below for details.
Edit Custom This setting allows the programming of up to 30 scenes for each of the 10 customizable
Programs programs, including colors and effects.
1.
2.
3.
4.
5.
6.
7.
8.
Go to the EDIT main level.
Select the desired auto program (PR. 01–10).
Select the desired scene (SC. 01–30).
Select the desired color or effect RED (red), GREN (green), BLUE (blue),
WHIT (white), STRB (strobe), TIME (step duration), or FADE (fade duration).
Select the value 000–255 for colors (0–100%) and durations (fast to slow), or
00–20 for the strobe (0–20 Hz).
Repeat the steps for other colors or effects.
Return to the scene level (SC. 01–30).
Repeat the settings of colors and effects for the other scenes.
Do not disconnect the product from power before completing the editing process.
Make sure to complete all steps when editing custom programs; otherwise, the
COLORado™ Batten Quad-9 Tour may lose any incomplete custom programming.
Strobe Personality This
setting allows you to select the
(random/slow/fast) strobe personalities.
1. Go to the SET main level.
2. Go to the STRB programming level.
3. Select a strobe personality (SPEC or CLAS).
-10-
classic
(01–20
Hz)
or
special
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Operation
Master/Slave The Master/Slave mode allows a group of COLORado™ Batten Quad-9 Tours (slaves)
to simultaneously duplicate the output of another COLORado™ Batten Quad-9 Tour
(master) without a DMX controller.
1. Set each of the slaves:
a. Go to RUN.
b. Select SLAV.
2. Set the master product:
a. Set the running mode to DMX (see DMX Control).
b. Select an auto or custom program as explained in Auto Programs, or a static
mix of colors as explained in Static Color.
·
The master is the product that runs an automatic program, a custom program, or in
Static Color mode.
·
Do not connect a DMX controller to the products configured for Master/Slave
operation. The DMX controller may interfere with signals from the master.
·
The master should be the first product in the daisy chain.
Color Settings The color setting determines how the product generates the white color based on
various RGB settings.
1. Go to the SET main level.
2. Go to the COLR programming level.
3. Select OFF, RGBW, or UC.
OFF:
RGBW:
UC:
When all the RGB faders are set to 255, the output is maximum, although
the resulting white color may not be balanced.
When all the RGB faders are set to 255, the resulting output is defined by
the configured white color (see White Calibration).
When all the RGB faders are set to 255, the output matches that of less
efficient products (Universal Color).
Dimmer Curves This setting provides you with four options to simulate the dimming curve of an
incandescent light product.
1. Go to the SET main level.
2. Go to the DIMX programming level.
3. Select the desired dimmer curve (OFF, DIM1, DIM2, DIM3, or DIM4).
The output is proportional (linear) to the dimmer and RGBW channel
values.
The output follows the dimmer and RGBW channel values based on the
DIM1–DIM4: corresponding dimmer curve, DIM1 being the fastest and DIM4 the
slowest.
OFF:
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
-11-
Operation
Curve Settings This setting allows you to select the dimmer curve shape using the red, green, blue,
white, and dimmer faders.
1. Go to the SET main level.
2. Go to the CURV programming level.
3. Select the desired dimmer curve (OFF, CV1, CV2, or CV3).
OFF
This output is proportional (linear) to the dimmer and RGBW channel
values.
CV1–CV3 This output follows the dimmer and RGBW channel values based on the
corresponding dimmer curve, CV1 being the fastest and CV3 the slowest.
For optimum control of the 16-bit dimming channels in the TR16 personality, be
sure that both dimming curves in SET > DIMX and SET > CURV are set to OFF.
Control Panel Lock This setting enables you to activate or disable the control panel lock, which keeps nonauthorized personnel from activating any of the control panel buttons.
1. Go to the SET main level.
2. Go to the KEY programming level.
3. Select ON or OFF.
When the control panel lock is active, the product will prompt you to enter the passcode
after 30 seconds of control panel inactivity or after turning on the product.
Passcode If you are prompted to enter a passcode on the product, press the buttons in the
following order: <UP>, <DOWN>, <UP>, <DOWN>, <ENTER>. The product’s passcode
cannot be changed and must be entered whenever you are prompted.
Note: Asterisks (*) appear on the display when entering the passcode.
Settings Lock This setting enables you to activate or disable the settings lock, which keeps
unauthorized personnel from making any changes to the programming levels under the
SET main level.
1. Go to the SET main level.
2. Go to the SLCK programming level
3. Select ON or OFF.
When the settings lock is activated, in order to access the SET programming levels, the
product will prompt you to enter the passcode. Enter the passcode as described in
Passcode.
-12-
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Operation
Program Upload This option allows you to transfer the custom programs of one product onto another
product using the Master/Slave mode.
1. Configure and connect the products in a Master/Slave arrangement, where the
master has the custom programs you want to transfer to the slaves.
2. From the master, go to the SET main level.
3. Go to the UPLD programming level.
4. Enter the passcode (see Passcode).
5. When SEND shows, press <ENTER> to start the upload.
6. Wait for the upload process to finish (the display will show OK before continuing or
turning the products off.
The Master/Slave products will provide the status of the process by lighting up as
follows:
·
Yellow indicates that the upload process is running.
·
Green indicates that the upload process completed successfully.
·
Red indicates that the upload process failed due to an error. Recheck all cable
connections and restart the process. If the issue persists, contact CHAUVET®
Technical Support.
Do not upload the data from a COLORado™ Batten Quad-9 Tour to a different
product, as the other product may become inoperative.
Resetting Factory This setting allows you to reset the product’s default values, including the custom
Defaults programs.
1.
2.
3.
4.
Go to the SET main level.
Select REST.
Enter the passcode (see Passcode).
Wait for the reset process to finish.
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
-13-
Operation
Resetting Calibration This setting allows you to reset the product’s default values set in the CAL1 and CAL2
Defaults programming levels. (See Setting the White Color for CAL1 settings and Calibrating the
White Color for CAL2 settings.)
1. Go to the CAL main level.
2. Enter the passcode (see Passcode).
3. Go to CALR.
4. Enter the passcode (see Passcode).
5. Wait for the reset process to finish.
Setting the This setting allows you to select and edit the color temperature of the white used in
White Color Channel 6 when in the TOUR mode or Channel 11 when in TR16 mode.
1.
2.
3.
4.
5.
6.
7.
Go to the CAL main level.
Enter the passcode (see Passcode).
Go to the CAL1 programming level.
Select a white color (WH.01–11).
Select a color RED (red), GREN (green), BLUE (blue), or WHIT (white).
Select a color value 000–255 (0–100%).
Repeat for the other colors.
Calibrating the This setting allows you to calibrate the white color when RGBW and the DMX controller’s
White Color red, green, and blue faders are set to 255.
1.
2.
3.
4.
5.
6.
Go to the CAL main level.
Enter the passcode (see Passcode).
Go to the CAL2 programming level.
Select the desired color RED (red), GREN (green), or BLUE (blue).
Select a desired color value 000 to 255 (0–100%).
Repeat for the other colors.
When selecting CAL > CAL2 >, you will only be able to define the values of red, green,
and blue.
The values of RED (red), GREN (green), and BLUE (blue) configured from CAL >
CAL2 > will define the color temperature shown when the RGB faders are set to
255 if SET > COLR > RGBW is active.
-14-
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Operation
TOUR Notes
These notes clarify the way the TOUR DMX personality works.
Master Dimmer ·
·
Channel 1 controls the intensity of the currently projected color.
When the slider is at the highest position (100%), the intensity of the output is at
maximum.
Red, Green, Blue, and ·
White Color Selection
Channels 2 through 5 control the intensity ratio of each of the red, green, blue, and
white LEDs.
·
When these channels are at the highest position (100%), the intensity of each color
is at maximum if SET > COLR is OFF.
·
You can combine channels 2 through 5 to create over one trillion colors.
Color Macros ·
Channel 6 selects the desired color macro.
·
Channel 6 has priority over channels 2 through 5.
·
Channel 1 controls the intensity of the color macro.
Strobe ·
Channel 7 controls the strobe frequency (not the intensity) of channels 2 through 6.
·
Channel 7 can strobe channels 2 through 5 when not running macros, allowing the
individual faders (R, G, B, and W), as well as channel 1 (dimmer), to control the
output intensity.
·
Channel 7 can strobe when running macros, with channel 6 selecting the macro and
channel 1 controlling the output intensity.
Auto/Custom ·
Programs
Channel 8 selects the preset auto programs AT.01–10 or the custom programs
PR.01–10.
·
When activating the custom programs PR.01–10, you can control the Step Time and
Fade Time using channels 2 and 3, respectively.
·
Channel 8 has priority over channels 2 through 7.
·
Channel 9 controls the speed at which each auto program plays.
Dimmer Speed ·
Channel 10 selects the Dimmer mode and speed. The Dimmer mode provides four
different options to simulate the dimming curve of an incandescent lighting product.
·
When the dimmer is set to OFF, the changes in the RGBW and Master Dimmer
faders are linear.
·
When the dimmer is set to DIM1–DIM4, DIM1 is the fastest dimmer curve and DIM4
is the slowest.
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
-15-
Operation
Menu Map
Main Level
Programming Levels
Description
RED
GREN
STAT
000–255
BLUE
Combine red, green, blue, and white to make a
custom color
WHIT
STRB
00–20
AT.
AUTO
01–10
PR.
RUN
ADDR
Selects the strobe frequency (0–20 Hz)
P.
000–255
10 customizable programs
DMX
DMX mode
SLAV
Slave mode
D.
001–512
PERS
10 automatic programs
Selects the DMX starting address
TOUR
11-channel: RGBW, dimmer, strobe, color
macro, auto/custom, dimmer speed, auto speed,
pixel selection
TR16
16-channel: 16-bit RGBW and dimmer, strobe,
color macro, auto/custom, dimmer speed, auto
speed, pixel selection
ARC.1
3-channel: RGB control
AR1.D
4-channel: RGB, dimmer
ARC.2
4-channel: RGBW control
AR2.D
5-channel: RGBW, dimmer
AR2.S
6-channel: RGBW, dimmer, strobe
HSV
3-channel: HSV control
PIX1
27-channel: RGB pixel control
PIX2
36-channel: RGBW pixel control
HALO
9-channel: 2700 K pixel control
RED
GREN
BLUE
EDIT
PR.
01–10
SC.
01–30
Combine red, green, blue, and white to generate
a custom color (0–100%)
WHIT
STRB
TIME
FADE
-16-
000–255
00–20
000–255
Selects the strobe frequency (0–20 Hz)
Defines the step duration (fast to slow)
Defines the fade duration (fast to slow)
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Operation
Menu Map (cont.)
Main Level
Programming Levels
Description
ON
KEY
Turns the passcode on or off
OFF
****
UPLD
(Enter Passcode)
****
REST
(Enter Passcode)
SEND/
OK
Uploads custom programs to other
COLORado™ Batten Quad-9 Tours
SEND/
OK
Defaults product to factory settings
OFF
COLR
RGB set to 255 = max. output
RGBW
RGB set to 255 = balanced white
UC.
Universal color balance
OFF
No dimmer
DIM1
DIMX
DIM2
Dimmer curve
DIM3
SET
DIM4
OFF
No dimmer
CV1
CURV
CV2
Fast (CV1) to slow (CV3) dimmer curves
CV3
DERR
SAVE
Blacks out fixture upon loss of DMX
BLAK
Continues with last command upon loss of DMX
control
OFF
SLCK
SET main level access lock
ON
SPEC
STRB
Selects strobe personality used in TOUR and
TR16 personalities
CLAS
RED
CAL1
CAL
WH.
01–11
Modifies the color macros used in the TOUR and
TR16 personalities
BLUE
WHIT
****
(Enter
Passcode)
GREN
000–
255
RED
CAL2
Defines the color temperature used when COLR
is set to RGBW
GREN
BLUE
CALR
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
****
(Enter Passcode)
Defaults CAL to factory settings
-17-
Operation
DMX Values
TOUR
Channel
Function
Percent/Setting
1
Dimmer
000 ó 255
0–100%
2
Red
000 ó 255
0–100% (Step Time if Custom 1–10 active)
3
Green
000 ó 255
0–100% (Fade Time if Custom 1–10 active)
4
Blue
000 ó 255
0–100%
5
White
000 ó 255
0–100%
Color Macro +
White Balance
000 ó 010
011 ó 030
031 ó 050
051 ó 070
071 ó 090
091 ó 110
111 ó 130
131 ó 150
151 ó 170
171 ó 200
201 ó 205
206 ó 210
211 ó 215
216 ó 220
221 ó 225
226 ó 230
231 ó 235
236 ó 240
241 ó 245
246 ó 250
251 ó 255
No function
R: 100%
R: 100%–0
R: 0
R: 0
R: 0–100%
R: 100%
R: 100%
R: 100%–0
R: 100%
White 1
White 2
White 3
White 4
White 5
White 6
White 7
White 8
White 9
White 10
White 11
Special Strobe
000 ó 009
010 ó 099
100 ó 109
110 ó 179
180 ó 189
190 ó 255
No function
Slow to fast
No function
Lighting effect, slow to fast
No function
*Select strobe
Random
Classic Strobe
000 ó 009
010 ó 019
020 ó 029
030 ó 039
040 ó 049
050 ó 059
060 ó 069
070 ó 079
080 ó 089
090 ó 099
100 ó 109
110 ó 119
120 ó 129
130 ó 139
140 ó 149
150 ó 159
160 ó 169
170 ó 179
180 ó 189
190 ó 199
200 ó 255
No function
1 Hz
2 Hz
3 Hz
4 Hz
5 Hz
6 Hz
7 Hz
8 Hz
9 Hz
10 Hz
11 Hz
12 Hz
13 Hz
14 Hz
15 Hz
16 Hz
17 Hz
18 Hz
19 Hz
20 Hz
6
7*
-18-
Value
G: 0–100% B: 0
G: 100% B: 0
G: 100% B: 0–100%
G: 100%–0 B: 100%
G: 0
B: 100%
G: 0
B: 100%–0
G: 0–100% B: 0–100%
G: 100%–0 B: 100%
G: 100% B: 100%
W: 100%
function in the
main menu under
SET > STRB,
select SPEC or
CLAS
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Operation
DMX Values (cont.)
TOUR
(cont.)
Channel
Function
Value
Percent/Setting
8
Programs
000 ó 040
041 ó 050
051 ó 060
061 ó 070
071 ó 080
081 ó 090
091 ó 100
101 ó 110
111 ó 120
121 ó 130
131 ó 140
141 ó 150
151 ó 160
161 ó 170
171 ó 180
181 ó 190
191 ó 200
201 ó 210
211 ó 220
221 ó 230
231 ó 255
9
Auto Speed
000 ó 255
0–100%
Dimmer Speed
000 ó 009
010 ó 029
030 ó 069
070 ó 129
130 ó 189
190 ó 255
Preset dimmer speed from display menu
Linear dimmer
Nonlinear dimming curve 1 (fastest)
Nonlinear dimming curve 2
Nonlinear dimming curve 3
Nonlinear dimming curve 4 (slowest)
Pixel Selection
000 ó 009
010 ó 019
020 ó 029
030 ó 039
040 ó 049
050 ó 059
060 ó 069
070 ó 079
080 ó 089
090 ó 099
100 ó 109
110 ó 119
120 ó 129
130 ó 139
140 ó 149
150 ó 159
160 ó 169
170 ó 179
180 ó 189
190 ó 199
200 ó 219
220 ó 239
240 ó 255
Pix 1, 2, 3, 4, 5, 6, 7, 8, 9 (static)
Pix 1 (static)
Pix 2 (static)
Pix 3 (static)
Pix 4 (static)
Pix 5 (static)
Pix 6 (static)
Pix 7 (static)
Pix 8 (static)
Pix 9 (static)
Pix 1, 2, 3 (static)
Pix 4, 5, 6 (static)
Pix 7, 8, 9 (static)
Pix 1, 2, 3, 7, 8, 9 (static)
Pix 1, 2, 3, 4, 5, 6 (static)
Pix 4, 5, 6, 7, 8, 9 (static)
Pix 1, 3, 5, 7, 9 (static)
Pix 2, 4, 6, 8 (static)
Chase left-to-right
Chase right-to-left
Chase left-right-left
Random
Pix 1, 2, 3, 4, 5, 6, 7, 8, 9 (static)
10
11
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
No function
Auto 1
Auto 2
Auto 3
Auto 4
Auto 5
Auto 6
Auto 7
Auto 8
Auto 9
Auto 10
Custom 1
Custom 2
Custom 3
Custom 4
Custom 5
Custom 6
Custom 7
Custom 8
Custom 9
Custom 10
-19-
Operation
DMX Values (cont.)
TR16
Channel
Value
Percent/Setting
1
Dimmer
000 ó 255
0–100%
2
Fine Dimmer
000 ó 255
0–100%
3
Red
000 ó 255
0–100%
4
Fine Red
000 ó 255
0–100%
5
Green
000 ó 255
0–100%
6
Fine Green
000 ó 255
0–100%
7
Blue
000 ó 255
0–100%
8
Fine Blue
000 ó 255
0–100%
9
White
000 ó 255
0–100%
10
Fine White
000 ó 255
0–100%
Color Macro +
White Balance
000 ó 010
011 ó 030
031 ó 050
051 ó 070
071 ó 090
091 ó 110
111 ó 130
131 ó 150
151 ó 170
171 ó 200
201 ó 205
206 ó 210
211 ó 215
216 ó 220
221 ó 225
226 ó 230
231 ó 235
236 ó 240
241 ó 245
246 ó 250
251 ó 255
No function
R: 100%
R: 100%–0
R: 0
R: 0
R: 0–100%
R: 100%
R: 100%
R: 100%–0
R: 100%
White 1
White 2
White 3
White 4
White 5
White 6
White 7
White 8
White 9
White 10
White 11
11
-20-
Function
G: 0–100% B: 0
G: 100% B: 0
G: 100% B: 0–100%
G: 100%–0 B: 100%
G: 0
B: 100%
G: 0
B: 100%–0
G: 0–100% B: 0–100%
G: 100%–0 B: 100%
G: 100% B: 100%
A: 100%
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Operation
DMX Values (cont.)
TR16
(cont.)
Channel
Function
Percent/Setting
Special Strobe
000 ó 009
010 ó 099
100 ó 109
110 ó 179
180 ó 189
190 ó 255
No function
Slow to fast
No function
Lighting effect, slow to fast
No function
Random
*Select strobe
Classic Strobe
000 ó 009
010 ó 019
020 ó 029
030 ó 039
040 ó 049
050 ó 059
060 ó 069
070 ó 079
080 ó 089
090 ó 099
100 ó 109
110 ó 119
120 ó 129
130 ó 139
140 ó 149
150 ó 159
160 ó 169
170 ó 179
180 ó 189
190 ó 199
200 ó 255
No function
1 Hz
2 Hz
3 Hz
4 Hz
5 Hz
6 Hz
7 Hz
8 Hz
9 Hz
10 Hz
11 Hz
12 Hz
13 Hz
14 Hz
15 Hz
16 Hz
17 Hz
18 Hz
19 Hz
20 Hz
Programs
000 ó 040
041 ó 050
051 ó 060
061 ó 070
071 ó 080
081 ó 090
091 ó 100
101 ó 110
111 ó 120
121 ó 130
131 ó 140
141 ó 150
151 ó 160
161 ó 170
171 ó 180
181 ó 190
191 ó 200
201 ó 210
211 ó 220
221 ó 230
231 ó 255
No function
Auto 1
Auto 2
Auto 3
Auto 4
Auto 5
Auto 6
Auto 7
Auto 8
Auto 9
Auto 10
Custom 1
Custom 2
Custom 3
Custom 4
Custom 5
Custom 6
Custom 7
Custom 8
Custom 9
Custom 10
12*
13
Value
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
function in the
main menu under
SET > STRB,
select SPEC or
CLAS
-21-
Operation
DMX Values (cont.)
TR16
(cont.)
Channel
14
15
16
ARC.1
AR1.D
ARC.2
-22-
Function
Value
Percent/Setting
Auto Speed
000 ó 255
0–100%
Dimmer Speed
000 ó 009
010 ó 029
030 ó 069
070 ó 129
130 ó 189
190 ó 255
Preset dimmer speed from display menu
Linear dimmer
Nonlinear dimming curve 1 (fastest)
Nonlinear dimming curve 2
Nonlinear dimming curve 3
Nonlinear dimming curve 4 (slowest)
Pixel Selection
000 ó 009
010 ó 019
020 ó 029
030 ó 039
040 ó 049
050 ó 059
060 ó 069
070 ó 079
080 ó 089
090 ó 099
100 ó 109
110 ó 119
120 ó 129
130 ó 139
140 ó 149
150 ó 159
160 ó 169
170 ó 179
180 ó 189
190 ó 199
200 ó 219
220 ó 239
240 ó 255
Pix 1, 2, 3, 4, 5, 6, 7, 8, 9 (static)
Pix 1 (static)
Pix 2 (static)
Pix 3 (static)
Pix 4 (static)
Pix 5 (static)
Pix 6 (static)
Pix 7 (static)
Pix 8 (static)
Pix 9 (static)
Pix 1, 2, 3 (static)
Pix 4, 5, 6 (static)
Pix 7, 8, 9 (static)
Pix 1, 2, 3, 7, 8, 9 (static)
Pix 1, 2, 3, 4, 5, 6 (static)
Pix 4, 5, 6, 7, 8, 9 (static)
Pix 1, 3, 5, 7, 9 (static)
Pix 2, 4, 6, 8 (static)
Chase left-to-right
Chase right-to-left
Chase left-right-left
Random
Pix 1, 2, 3, 4, 5, 6, 7, 8, 9 (static)
Channel
Function
Value
Percent/Setting
1
Red
000 ó 255
0–100%
2
Green
000 ó 255
0–100%
3
Blue
000 ó 255
0–100%
Channel
Function
Value
Percent/Setting
1
Dimmer
000 ó 255
0–100%
2
Red
000 ó 255
0–100%
3
Green
000 ó 255
0–100%
4
Blue
000 ó 255
0–100%
Channel
Function
Value
Percent/Setting
1
Red
000 ó 255
0–100%
2
Green
000 ó 255
0–100%
3
Blue
000 ó 255
0–100%
4
White
000 ó 255
0–100%
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Operation
DMX Values (cont.)
AR2.D
AR2.S
Channel
Value
Percent/Setting
1
Dimmer
000 ó 255
0–100%
2
Red
000 ó 255
0–100%
3
Green
000 ó 255
0–100%
4
Blue
000 ó 255
0–100%
5
White
000 ó 255
0–100%
Channel
Function
Value
Percent/Setting
1
Dimmer
000 ó 255
0–100%
2
Red
000 ó 255
0–100%
3
Green
000 ó 255
0–100%
4
Blue
000 ó 255
0–100%
5
White
000 ó 255
0–100%
Classic Strobe
000 ó 009
010 ó 019
020 ó 029
030 ó 039
040 ó 049
050 ó 059
060 ó 069
070 ó 079
080 ó 089
090 ó 099
100 ó 109
110 ó 119
120 ó 129
130 ó 139
140 ó 149
150 ó 159
160 ó 169
170 ó 179
180 ó 189
190 ó 199
200 ó 255
No function
1 Hz
2 Hz
3 Hz
4 Hz
5 Hz
6 Hz
7 Hz
8 Hz
9 Hz
10 Hz
11 Hz
12 Hz
13 Hz
14 Hz
15 Hz
16 Hz
17 Hz
18 Hz
19 Hz
20 Hz
6
HSV
Function
Channel
Function
Value
Percent/Setting
1
Hue
000 ó 255
0–100%
2
Saturation
000 ó 255
0–100%
3
Value
000 ó 255
0–100%
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
-23-
Operation
DMX Values (cont.)
PIX1
HALO
-24-
Channel
Function
Value
Percent/Setting
1
Pixel 1 Red
000 ó 255
0–100%
2
Pixel 1 Green
000 ó 255
0–100%
3
Pixel 1 Blue
000 ó 255
0–100%
4
Pixel 2 Red
000 ó 255
0–100%
5
Pixel 2 Green
000 ó 255
0–100%
6
Pixel 2 Blue
000 ó 255
0–100%
7
Pixel 3 Red
000 ó 255
0–100%
8
Pixel 3 Green
000 ó 255
0–100%
9
Pixel 3 Blue
000 ó 255
0–100%
10
Pixel 4 Red
000 ó 255
0–100%
11
Pixel 4 Green
000 ó 255
0–100%
12
Pixel 4 Blue
000 ó 255
0–100%
13
Pixel 5 Red
000 ó 255
0–100%
14
Pixel 5 Green
000 ó 255
0–100%
15
Pixel 5 Blue
000 ó 255
0–100%
16
Pixel 6 Red
000 ó 255
0–100%
17
Pixel 6 Green
000 ó 255
0–100%
18
Pixel 6 Blue
000 ó 255
0–100%
19
Pixel 7 Red
000 ó 255
0–100%
20
Pixel 7 Green
000 ó 255
0–100%
21
Pixel 7 Blue
000 ó 255
0–100%
22
Pixel 8 Red
000 ó 255
0–100%
23
Pixel 8 Green
000 ó 255
0–100%
24
Pixel 8 Blue
000 ó 255
0–100%
25
Pixel 9 Red
000 ó 255
0–100%
26
Pixel 9 Green
000 ó 255
0–100%
27
Pixel 9 Blue
000 ó 255
0–100%
Channel
Function
Value
Percent/Setting
1
Pixel 1 Dimmer 2700 K
000 ó 255
0–100%
2
Pixel 2 Dimmer 2700 K
000 ó 255
0–100%
3
Pixel 3 Dimmer 2700 K
000 ó 255
0–100%
4
Pixel 4 Dimmer 2700 K
000 ó 255
0–100%
5
Pixel 5 Dimmer 2700 K
000 ó 255
0–100%
6
Pixel 6 Dimmer 2700 K
000 ó 255
0–100%
7
Pixel 7 Dimmer 2700 K
000 ó 255
0–100%
8
Pixel 8 Dimmer 2700 K
000 ó 255
0–100%
9
Pixel 9 Dimmer 2700 K
000 ó 255
0–100%
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Operation
DMX Values (cont.)
PIX2
Channel
Function
Value
Percent/Setting
1
Pixel 1 Red
000 ó 255
0–100%
2
Pixel 1 Green
000 ó 255
0–100%
3
Pixel 1 Blue
000 ó 255
0–100%
4
Pixel 1 White
000 ó 255
0–100%
5
Pixel 2 Red
000 ó 255
0–100%
6
Pixel 2 Green
000 ó 255
0–100%
7
Pixel 2 Blue
000 ó 255
0–100%
8
Pixel 2 White
000 ó 255
0–100%
9
Pixel 3 Red
000 ó 255
0–100%
10
Pixel 3 Green
000 ó 255
0–100%
11
Pixel 3 Blue
000 ó 255
0–100%
12
Pixel 3 White
000 ó 255
0–100%
13
Pixel 4 Red
000 ó 255
0–100%
14
Pixel 4 Green
000 ó 255
0–100%
15
Pixel 4 Blue
000 ó 255
0–100%
16
Pixel 4 White
000 ó 255
0–100%
17
Pixel 5 Red
000 ó 255
0–100%
18
Pixel 5 Green
000 ó 255
0–100%
19
Pixel 5 Blue
000 ó 255
0–100%
20
Pixel 5 White
000 ó 255
0–100%
21
Pixel 6 Red
000 ó 255
0–100%
22
Pixel 6 Green
000 ó 255
0–100%
23
Pixel 6 Blue
000 ó 255
0–100%
24
Pixel 6 White
000 ó 255
0–100%
25
Pixel 7 Red
000 ó 255
0–100%
26
Pixel 7 Green
000 ó 255
0–100%
27
Pixel 7 Blue
000 ó 255
0–100%
28
Pixel 7 White
000 ó 255
0–100%
29
Pixel 8 Red
000 ó 255
0–100%
30
Pixel 8 Green
000 ó 255
0–100%
31
Pixel 8 Blue
000 ó 255
0–100%
32
Pixel 8 White
000 ó 255
0–100%
33
Pixel 9 Red
000 ó 255
0–100%
34
Pixel 9 Green
000 ó 255
0–100%
35
Pixel 9 Blue
000 ó 255
0–100%
36
Pixel 9 White
000 ó 255
0–100%
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
-25-
Technical Information
5. Technical Information
Product
Maintenance
To maintain optimum performance and minimize wear, you should clean this product
frequently. Usage and environment are contributing factors in determining the cleaning
frequency.
As a rule, clean this product at least twice a month. Dust build-up reduces light output
performance and can cause overheating. This can lead to reduced light source life and
increased mechanical wear.
To clean your product:
·
Unplug the product from power.
·
Wait until the product is at room temperature.
·
Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external vents.
·
Clean all external surfaces with a mild solution of non-ammonia glass cleaner or
isopropyl alcohol.
·
Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
·
Wipe any dirt or grime to the outside edges of the lens surface.
·
Gently polish the lens surfaces until they are free of haze and lint.
Always dry the external surfaces thoroughly and carefully after cleaning them.
Do not spin the cooling fan using compressed air because you could damage it.
Returns
You must send the product prepaid, in the original box, and with the original packing and
accessories. CHAUVET® will not issue call tags.
Call CHAUVET® and request a Return Merchandise Authorization (RMA) number
before shipping the product. Be prepared to provide the model number, serial number,
and a brief description of the cause(s) for the return.
Clearly label the package with an RMA number. CHAUVET® will refuse any product
returned without an RMA number.
Do not write the RMA number directly on the box. Instead, write it on a properly affixed
label.
Once you have received the RMA number, include the following information on a piece
of paper inside the box:
·
Your name
·
Your address
·
Your phone number
·
The RMA number
· A brief description of the problem(s)
Be sure to pack the product properly. Any shipping damage resulting from inadequate
packaging will be the customer’s responsibility. FedEx packing or double-boxing are
recommended.
CHAUVET® reserves the right to use its own discretion to repair or replace returned
product(s).
-26-
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
Technical Information
Technical Specifications
Dimensions and
Weight
Length
Width
Height
Weight
38 in (975 mm)
7.8 in (200 mm)
7.5 in (190 mm)
14.4 lb (6.5 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Light Source
Photo Optic
Thermal
DMX
Ordering
Power Supply Type
Range
Voltage Selection
Switching (Internal)
100 to 240 VAC, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
Operating current
Power linking current (units)
Fuse
181 W
1.5 A
13.6 A (9 units)
T 3.15 A, 250 V
206 W
0.9 A
13.6 A (15 units)
T 3.15 A, 250 V
Power I/O
U.S./Worldwide
Europe
Power input connector
Power output connector
Power cord plug
Neutrik® powerCON® A
Neutrik® powerCON® B
Edison (U.S.)
Neutrik® powerCON® A
Neutrik® powerCON® B
Local plug
Type
Power
Lifespan
LED
10 W
50,000 hours
Color
Quantity
Current
Quad-color (RGBW)
9
800 mA
Parameter
Standard Optics
Illuminance @ 5 m
Beam angle
Field angle
1,026 lx
17° x 15°
31° x 30°
Max. External Temperature
Cooling System
113 °F (45 °C)
Fan-assisted Convection
I/O Connectors
Connector Type
Channel Range
3- and 5-pin XLR
Sockets
3, 4, 5, 6, 9, 11, 16, 27 or 36
Product Name
Item Code
UPC Number
COLORado™ Batten
Quad-9 Tour
01030801
781462211493
COLORado™ Batten Quad-9 Tour User Manual Rev. 1
-27-
Contact Us
WORLD HEADQUARTERS - CHAUVET®
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice:
(954) 577-4455
Fax:
(954) 929-5560
Toll free: (800) 762-1084
Technical Support
Voice:
(954) 577-4455 (Press 4)
Fax:
(954) 756-8015
Email:
[email protected]
World Wide Web www.chauvetlighting.com
UNITED KINGDOM AND IRELAND - CHAUVET® Europe Ltd.
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice:
+44 (0)1773 511115
Fax:
+44 (0)1773 511110
Technical Support
Email:
[email protected]
World Wide Web www.chauvetlighting.co.uk
MEXICO - CHAUVET® Mexico
General Information
Address: Av. Santa Ana 30
Parque Industrial Lerma
Lerma, Mexico C.P. 52000
Voice:
+52 (728) 285-5000
Technical Support
Email:
[email protected]
World Wide Web www.chauvet.com.mx
Outside the U.S., United Kingdom, Ireland, or Mexico, contact your dealer. Follow their instructions to request
support or to return a product. Visit our website for contact details.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement