Mille / Mille R / Tuono

Mille / Mille R / Tuono
Installation Instructions
V.A.L.E.
1.
Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the sidestand or
ideally a service lift.
2.
Unhook the springs holds the stock canister to the headers under the bike.
3.
Remove the hardware that holds the stock canister at the exhaust bracket. Take off the stock canister.
4.
Install the new s-bend into the stock header.
5.
Install VALE adapter kit using supplied kit instructions.
6.
Place a bead of the hi-temp sealant on the outside edge of the s-bend that goes into the canister. Slide the TBR canister
onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out.
7.
Carefully slide the muffler clamp over the muffler. (Note: The stainless steel canister clamp and the name badge on the
canister come from the factory with a clear plastic protective film. Please remove this film before operation.) You may
need to twist and turn the S-bend a little to get it in the right place. Locate both tabs of the canister clamp on the outside of
the exhaust bracket. Use the stock hardware to secure it. Leave loose for now.
8.
Make sure everything is aligned and tighten all hardware. Reinstall the stock springs at the s-bend/header junction. Affix
the two connector springs to the muffler.
9.
Before you run the bike, clean off all fingerprints and dirt, as any oily residue will etch the metal and become somewhat
permanent when the system gets hot. Run the bike and enjoy. It is normal for some white smoke to appear the first time
you start the bike. This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you find a
leak, a little high temperature silicon sealant should fix it. After 50 to 100 miles, recheck all fasteners for tightness.
TM
Aprilia
V a r i a b l e
A x i s
L o c k i n g
E x h a u s t
Mille & Mille R
V.A.L.E.™ Slip-on Exhaust System with M-2 Canister
Part # 005-760406M, 005-760407M, 005-760408M, 005-760419M, 005-760420M
Parts List
Qty. Description
Part Number
1
Muffler
1
Muffler Clamp
1
S-Bend Tube (Speed Triple)
1
HARDWARE KIT
1
VALE Adapter Kit
2
80mm swivel hook spring
1
Permatex Ultra Black Gasket Maker
1
T20 Torx Screw Wrench
1
TBR Sticker Kit
Varies
Varies
005-7604N
005-76-3
005-2-1-V
005-S80
031-P22072
005-9-15820
015-10212
Care & Cleaning
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualified motorcycle
technician. If you have any doubts as to your ability to install this performance part,
please consult with your local motorcycle dealer. Read all instructions first before
starting installation. Make sure the motorcycle and exhaust system are completely cool
before starting the installation. Also, make sure the bike is secure on a center stand
or ideally a service lift during installation. Be sure to save all stock components for
possible use later.
Warranty
Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as is”
without warranty. Two Brothers Racing specifically disclaims any warranties of merchantability or fitness for a particular
purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use
of these products or parts.
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. For cleaning use a mild spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue after a few heat cycles, this is a normal characteristic of high quality stainless
steel.
Carbon Fiber Mufflers: Always make sure the fiberglass packing inside is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the Carbon Fiber sleeve. TBR sells repack kits (TBR part # 005-10038) that include new rivets and repack material as well as a drill bit (#30), making
it easy to do yourself. Also, NEVER dyno test your bike with carbon fiber mufflers installed - the intense heat and lack of cooling air can quickly cause the CF
material to burn. Two Brothers Racing does not provide a warranty for burned carbon fiber.
Aluminum Mufflers: Use an aluminum or mag wheel polish such as Mother’s to restore the bright finish to factory spec.
Repack all road canisters every 3,000 miles. Part #005-10038
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement