04_TSX_XMRadio
INSTALLATION
INSTRUCTIONS
Accessory
Application
XM RADIO SYSTEM
2004 TSX
Publications No.
BII 25222
Issue Date
JULY 2003
PARTS LIST
XM Radio Attachment (sold separately):
P/N 08B15-SEC-200
Display module pocket
DIN cable
Clip nut
XM radio harness
3 Self-tapping screws
Fastener
Front unit bracket
6 Washer-screws, 4 x 8 mm
Rear unit bracket
6 Washer-bolts, 6 x 12 mm
Bracket A
29 Wire ties
Connector clip
Bracket B
5 Wire tie with clips
Bracket C
2 Cushion tapes
3 EPT seals
Double-sided adhesive tape
Fuse label
4 Flange nuts, 4 mm
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
Mini fuse, 5 A
BII 25222 (0307)
1 of 20
Attachment Kit (sold separately):
P/N 08B06-SEC-210
Wire tie with clip
Right upper player bracket
8 Flange nuts, 6 mm
Left upper player bracket
2 Latches
Cushion tape
Lower player bracket
XM Antenna (sold separately):
P/N 08A15-1E1-100
Antenna
Right player bracket
Unit Kit (sold separately):
P/N 08A15-1E1- 000
Left player bracket
Display Module
FM modulator unit
Player panel
Receiver unit
BUS cable (not used)
Owner’s Manual
2 Wire ties
2 of 20
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
INSTALLATION
TOOL AND SUPPLIES REQUIRED
Phillips screwdriver
Stubby Phillips screwdriver
Flat-tip screwdriver
Hook tool
Isopropyl alcohol
Shop towel
Tape measure
Utility knife
Ratchet
8 mm and 10 mm Sockets
Felt-tip pen
Scissors
Drill
7 mm Drill bit
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures should
not be attempted by “do-it-yourselfers.”
1.
Make sure you have the anti-theft code for the
radio, then write down the frequencies for the
preset buttons.
2.
Disconnect the negative cable from the battery.
3.
Remove the trim ring.
M/T Model:
Illustration of the XM Radio System Installed on the
Vehicle
DISPLAY MODULE
•
Pull up on the parking brake lever to prevent
the vehicle from moving.
•
Loosen the lock nut and remove the shift knob
by turning it counterclockwise.
•
Remove the lock nut.
RECEIVER
UNIT
ANTENNA
SHIFT
KNOB
FM MODULATOR
UNIT
3211010B
VEHICLE
ANTENNA
CABLE
DISPLAY
MODULE
LOCK
NUT
FM MODULATOR
UNIT
2031021S
DIN CABLE
RECEIVER UNIT
FUSE BOX
6-PIN CONNECTOR
XM RADIO
HARNESS
ANTENNA
2N28010M
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 25222 (0307)
3 of 20
•
Gently pry up on the trim ring to release the
eight clips.
•
Unplug the two seat heater connectors, and
remove the trim ring.
CLIPS (8)
4.
Open the pocket lid. Pull the pocket out toward
you to release the four clips, unplug the
illumination bulb, and remove the pocket. Take
care not to damage the illumination bulb.
TRIM
RING
ILLUMINATION
BULB
CLIP
LID
POCKET
2031051S
CLIPS (4)
SEAT HEATER
CONNECTOR
5.
2031030S
Remove the coin pocket holder or ashtray holder.
A/T Model:
With Coin Pocket Holder:
•
Pull up on the parking brake lever to prevent
the vehicle from moving.
•
Remove the four self-tapping screws.
•
Move the shift lever into Neutral.
•
•
Gently pry up on the trim ring to release the
eight clips.
Gently pull out the coin pocket holder to
release the clip from the coin pocket holder
and unplug the vehicle connector. Remove the
coin pocket holder.
•
Unplug the two seat heater connectors and
remove the trim ring.
CLIPS (8)
SELF-TAPPING
SCREW
(Reuse.)
CLIP
TRIM
RING
COIN
POCKET
HOLDER
VEHICLE
CONNECTOR
SEAT HEATER
CONNECTOR
4 of 20
2N03011S
2031040S
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
With Ashtray Holder:
7.
•
Remove the four self-tapping screws.
•
Gently pull out the ashtray holder, unplug the
illumination bulb, vehicle connector and
cigarette lighter harness 2-pin connector.
Remove the ashtray holder.
SELF-TAPPING
SCREW (Reuse.)
Remove the rear console.
•
Open the lid and remove the rear console mat
from inside of the rear console.
•
Remove the two screws and the four selftapping screws, and unplug the connector and
harness clip.
REAR
CONSOLE MAT
VEHICLE CONNECTOR
SELF-TAPPING
SCREWS (4)
LID
VEHICLE CLIP
REAR
CONSOLE
ASHTRAY
HOLDER
ILLUMINATION BULB
6.
CIGARETTE
LIGHTER
HARNESS
2-PIN
CONNECTOR
SCREWS
(2)
HARNESS CLIP
3305011S
Remove the illumination bulb, and attach the
electrical tape as shown. Bundle any excess
illumination bulb harness, and secure it to the
vehicle harness with one wire tie.
CONNECTOR
8.
Remove the driver's dashboard lower cover (one
self-tapping screw, retaining clip and two hooks).
ELECTRICAL TAPE
WIRE TIE
2N01030Y
HOOKS (2)
ILLUMINATION
BULB
(Remove.)
VEHICLE
HARNESS
RETAINING
CLIP
ILLUMINATION
BULB HARNESS
DASHBOARD
LOWER COVER
SELF-TAPPING
SCREW
2N01080Y
2N21112S
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 25222 (0307)
5 of 20
9.
Remove the driver's dashboard under cover
(release the three clips, tab, and pin).
11. Remove the passenger's dashboard under cover
(release the three clips, one tab, and three pins).
CLIP
PINS (3)
2N19010S
PIN
TAB
TAB
DASHBOARD
UNDER COVER
CLIPS (3)
10. Remove the left side console cover. Remove the
self-taping screw, clip, and release the three
retaining clips.
12. Remove the glove box (two stops, damper rod,
and two bolts).
SCREW
STOPS (2)
DAMPER
ROD
CLIPS (3)
CLIP
CONSOLE
COVER
GLOVE BOX
BOLTS (2)
6 of 20
BII 25222 (0307)
3211081B
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
If the vehicle is equipped with other accessories:
Installing the XM Radio Harness and FM Modulator
Unit
•
Unplug the other accessory harness 6-pin
connector from the fuse box.
•
Remove the dummy connector from the XM
radio harness.
•
Plug the XM radio harness 6-pin connector into
the fuse box 6-pin connector, then plug the
other accessory 6-pin connector into the XM
radio harness 6-pin connector.
13. Attach the fuse labels to the fuse cases on the
XM radio harness.
FUSE LABEL
When attaching the
fuse labels to the
fuse cases, open the
fuse case cover and
make sure that the
fuse is in the case.
3121030M
Use these labels.
OTHER
ACCESSORY
6-PIN
HARNESS
FUSE BOX
6-PIN
CONNECTOR
6-PIN
CONNECTOR
FUSE
CASES
XM RADIO HARNESS
6-PIN CONNECTOR
DUMMY
CONNECTOR
(Discard.)
2524060M
FUSE
LABEL
2A
LABEL
5A
LABEL
15. Install the fuse cases and the dummy 6-pin
connector from the XM radio harness to the fuse
box case.
XM
RADIO
HARNESS
CLIP
FUSE CASE
POSITION
ON THE
FUSE BOX
CASE
2524051M
14. On the fuse box, locate the 6-pin connector. Plug
the XM radio harness 6-pin connector into the fuse
box 6-pin connector.
FUSE
CASES
VEHICLE
HARNESS
WIRE TIE
XM RADIO
HARNESS
3226030B
XM RADIO HARNESS 6-PIN CONNECTOR
WITH DUMMY CONNECTOR
(Do not secure to the yellow SRS
harness.)
16. Secure the XM radio harness to the vehicle
harness with the wire tie.
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 25222 (0307)
7 of 20
17. Route the XM radio harness under the steering
shaft and on the inside of the center console.
20. Locate the welded nut on the vehicle stay.
Remove the vehicle ground bolt, and attach the
ground terminal of the XM radio harness with the
removed bolt.
VEHICLE
HARNESS
VEHICLE GROUND
TERMINAL
GROUND
TERMINAL
VEHICLE
GROUND
BOLT
WIRE
TIES (3)
3218010B
XM RADIO
HARNESS
XM RADIO
HARNESS
3-PIN
CONNECTOR
18. Loosely secure the XM radio harness to the
vehicle harness with three wire ties.
3211020B
XM RADIO
HARNESS
19. Using a hook tool, pull out on the driver's
instrument side trim to release the three clips,
and unplug the vehicle connector and the hose.
Remove the side trim.
21. Route the XM radio harness 3-pin connector
toward the glove box opening.
22. In the glove box opening, locate the frame stay
pipe. Align the holes in the frame stay pipe with
the welded nuts in the bracket A, and loosely
attach bracket A to the pipe frame with the two
6 x 12 mm washer-bolts.
HOSE
VEHICLE
CONNECTOR
HOOK
TOOL
BRACKET A
PIPE FRAME
STAY
6 x 12 mm
WASHER-BOLT
Pull out.
3123011B
CLIPS (3)
DRIVER'S
INSTRUMENT
SIDE TRIM
6 x 12 mm
WASHER BOLT
8 of 20
BII 25222 (0307)
3211090B
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
23. Attach the connector clip to the harness connector
of the FM modulator unit. Attach bracket B to the
FM modulator unit with one 4 x 8 mm washerscrew. Tighten the washer-screw securely.
25. Below the glove box opening, remove the upper
heater blower case mounting bolt.
4 x 8 mm
WASHERSCREW
BRACKET B
3212040B
BOLT
(Reuse.)
FM
MODULATOR
UNIT
CONNECTOR
CLIP
2524121M
HEATER
BLOWER CASE
26. Attach the bracket C to the bottom of the FM
modulator unit with one 4 x 8 mm washer-screw
and the vehicle bolt removed in step 25.
24. Attach bracket B with the FM modulator unit
against bracket A, and install one additional
6 x 12 mm washer-bolt. Tighten all three
6 x 12 mm washer-bolts securely.
27. On the back of the FM modulator unit, attach one
wire tie with clip to the antenna harnesses,
and attach the wire tie with clip to the hole in
bracket C.
FM
MODULATOR
UNIT
HARNESS
BRACKET A
WIRE TIE
WITH CLIP
FM
MODULATOR
UNIT
6 x 12 mm
WASHER-BOLT
BRACKET B
FM MODULATOR
UNIT ANTENNA
HARNESS
3211100B
3212050B
BRACKET C
4 x 8 mm
WASHER SCREW
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 25222 (0307)
VEHICLE
BOLT
(reused)
9 of 20
28. Connect the XM radio harness 3-pin connector to
the FM modulator unit harness 3-pin connector,
then attach the 3-pin connector clip to the hole in
bracket B.
Installing the Display Module
29. Slide the clip nut onto the display module pocket
flange.
DISPLAY MODULE
POCKET FLANGE
BRACKET B
CLIP
XM RADIO
HARNESS 3-PIN
CONNECTOR
Clean with isopropyl
alcohol.
DISPLAY MODULE
POCKET
DISPLAY
MODULE
FM MODULATOR
UNIT HARNESS 3-PIN
CONNECTOR
3212110B
3121040M
BACKING
DOUBLE-SIDED
ADHESIVE TAPE
Clean with isopropyl
alcohol.
30. Using isopropyl alcohol on a shop towel, clean the
bonding surface on the display module and display
module pocket.
31. Remove the adhesive backing from the doubleface adhesive tape, then attach it to the display
module back. Remove the adhesive backing from
the double-face adhesive tape on the display
module.
32. Route the display module cable through the hole
of the display module pocket. Attach the display
module to the display module pocket while pulling
the display module cable.
10 of 20
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
33. Install one latch to each player bracket.
36. Plug the DIN cable and display module cable into
the FM modulator unit. Route the FM modulator
unit antenna harness along the DIN cable and on
the inside of the front console.
LEFT PLAYER
BRACKET
RIGHT PLAYER
BRACKET
DISPLAY
MODULE
CABLE
FM MODULATOR UNIT
LATCH
LATCH
SELFTAPPING
SCREWS (3)
3211030B
DISPLAY MODULE
POCKET
FM
MODULATOR
UNIT ANTENNA
HARNESS
34. Assemble the display module pocket with the left
player bracket and right player bracket with the
three self-tapping screws.
35. Route the DIN cable and display module cable
along the XM radio harness (3-pin connector side)
to the FM modulator unit.
3212120B
DIN CABLE
37. Unplug the vehicle antenna cable, and plug it into
the FM modulator unit antenna cable. Plug the
other FM module antenna jack into the vehicle
antenna cable.
XM RADIO
HARNESS
DIN
CABLE
DIN CABLE/DISPLAY
MODULE CABLE
WIRE TIE
WIRE TIE
To the FM
modulator
unit
FM
MODULATOR
ANTENNA
JACK
DISPLAY
MODULE CABLE
EPT
SEAL
3211040B
DISPLAY
MODULE
3211050B
VEHICLE
ANTENNA JACK
38. Wrap one EPT seal around the antenna jack, and
secure the antenna jack to the vehicle antenna
jack with one wire tie. Secure the DIN cable, the
display module cable, and the antenna harness to
the vehicle harness with one wire tie.
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 25222 (0307)
11 of 20
39. Secure the XM radio harness to the vehicle
harness with two wire ties. Bundle up the excess
display module cable, and secure it with one wire
tie.
WIRE TIES (2)
XM RADIO
HARNESS
Routing the XM Radio Harness, DIN Cable and
Antenna cable
VEHICLE
HARNESS
41. Inside the passenger compartment, remove the
rear seat cushion by removing the bolt and
releasing the two hooks (pull the hook out toward
you).
REAR SEAT
CUSHION
BOLT
3211060B
3212011B
40. Insert the studs from the right and left upper
player brackets into the holes in the vehicle frame.
Install the 6 mm flange nuts on the end of each
stud, and tighten the flange nuts securely. Set the
display module assembly aside; it will be installed
later.
HOOKS (2)
42. Remove the right side cushion by removing one
bolt and one hook.
6 mm
FLANGE NUT
40 mm BOLT
HOOK
CUSHION
LEFT UPPER
PLAYER
BRACKET
STUDS (2)
RIGHT UPPER
PLAYER
BRACKET
STUDS (2)
12 of 20
6 mm
FLANGE
NUT
2N02041S
BOLT
BII 25222 (0307)
3212020B
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
43. Fold down each rear seat back by pulling the lever
under the rear parcel shelf inside the trunk.
45. Remove the rear trim panel (four clips).
REAR TRIM PANEL
REAR SEAT
BACKS (2)
Down
Pull.
Down
TRUNK WEATHERSTRIP
LEVERS (2)
3212030B
CLIPS (4)
2325010T
If the vehicle is not equipped with a cargo net, go
to step 51; otherwise, go to step 46.
46. Remove the cargo net from the "A" and "B" hooks
on the right trunk side trim. Then remove the "A"
and "B" hooks.
44. Remove the spare tire cover (one clip).
CLIP
"A" AND "B" HOOKS (4)
RUBBER
STRAPS
(4)
CARGO NET
SPRING
WASHER
SPARE TIRE COVER
2322010T
HOOK "A"
HOOK "B"
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 25222 (0307)
RIGHT TRUNK
SIDE TRIM
13 of 20
47. Remove the right trunk side trim (four clips). Take
care not to damage the clips and retaining clips.
49. Measure and mark the rear unit bracket using a
felt-tip pen as shown. While wearing eye
protection, drill a 7 mm hole through the mark in
the rear unit bracket.
RIGHT TRUNK
SIDE TRIM
TRUNK TRIM
RETAINING
CLIP
19.5 mm
7 mm
DRILL
WASHER
40 mm
BOLT
COLLAR
(LONG)
SPRING
WASHER
Remove.
WASHER
62.5 mm
FLANGE
NUT
CLIPS (4)
3211071B
48. Remove the upper flange nut, long collar and
washer, then remove the 40 mm bolt, washer and
spring washer.
ELONGATED
HOLE
WASHER
50. Insert the 40 mm bolt with washers through the
7 mm drilled hole.
51. Route the XM radio harness and the DIN cable
along the vehicle harness toward the parking
brake lever. Secure the harness and DIN cable to
the vehicle harness with five wire ties in the areas
shown.
VEHICLE
HARNESS
XM RADIO
HARNESS
AND DIN
CABLE
RIGHT TRUNK
SIDE PANEL
FLANGE NUT
14 of 20
LONG
COLLAR
WIRE TIES (5)
BII 25222 (0307)
2527072M
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
52. Raise the rear seat back. Pull the DIN cable and
XM radio harness out from under the floor carpet
and toward the passenger's side of the vehicle.
Secure the XM radio harness and DIN cable to the
vehicle harness with seven wire ties.
54. Inside the trunk, unplug the vehicle harness
connector from the brake light case. Release the
four hooks of the brakelight case from the parcel
shelf, and remove the brake light case.
BRAKE LIGHT CASE
VEHICLE
HARNESS
XM RADIO
HARNESS
AND DIN
CABLE
HOOKS (4)
VEHICLE
HARNESS
CLIP
PARCEL SHELF
CONNECTOR
2527060M
WIRE
TIES (7)
3212091B
53. Route the XM radio harness and DIN cable along
the vehicle harness toward the trunk. Secure the
XM radio harness and DIN cable to the vehicle
harness with two additional wire ties.
WIRE TIE (2)
DIN
CABLE
XM RADIO
HARNESS
3212100B
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 25222 (0307)
15 of 20
55. Using isopropyl alcohol on a shop towel, clean the
bottom of the antenna. Remove the adhesive
backing from the fastener, and attach the fastener
to the bottom of the antenna.
CUSHION
TAPE
58. Measure and mark the cutting area on the brake
light case. Using a utility knife, cut out the brake
light case in the area shown. Remove any burrs
from the edges of the groove. Route the antenna
cable through the case groove and install the
brake light case.
ANTENNA
Clean with
isopropyl alcohol.
BRAKE LIGHT
CASE
Cut.
ADHESIVE
BACKING
10 mm
5 mm
20 mm
MARK
REAR TRAY
3212061B
FASTENER
10 mm
56. Route the antenna cable through the high-mount
brake light opening, and install the antenna to the
rear tray in the area shown. Attach one cushion
tape to the edge of the rear parcel shelf where the
antenna cable touches.
5 mm
3212071B
59. Route the antenna cable along the vehicle
harness, and secure the antenna cable to the
vehicle harness with five wire ties in the areas
shown.
57. Align the antenna cable on the rear tray with the
brake light case, then using a felt-tip pen, mark
the cable position on the edge of the case.
VEHICLE
HARNESS
NAVIGATION UNIT
(if equipped)
MARK
ANTENNA
CABLE
FELT-TIP PEN
BRAKE LIGHT
CASE
REAR
TRAY
ANTENNA
CABLE
WIRE TIE
3213011B
Align.
ANTENNA
CABLE
16 of 20
Straight.
3212081B
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
60. Secure the antenna cable, the DIN cable, and the
XM radio harness to the vehicle harness with two
wire ties.
62. Position the receiver unit between the right trunk
side panel and rear fender panel, and plug in the
antenna cable connectors, the DIN cable
connector, and the XM radio harness connector to
the receiver unit.
ANTENNA
CABLE
XM RADIO
HARNESS
DIN CABLE
RECEIVER
UNIT
VEHICLE
HARNESS
XM RADIO
HARNESS
WIRE TIE (2)
REAR
FENDER
PANEL
3213020B
DIN CABLE
ANTENNA
CABLE
3213030B
RIGHT TRUNK
SIDE PANEL
61. Install the front and rear unit brackets to the
receiver unit using two 4 x 8 mm washer-screws
and two 4 mm flange nuts for each bracket. If
equipped with a cargo net, make sure the 40 mm
bolt and washers are in place.
FRONT UNIT
BRACKET
63. Attach the receiver unit/brackets to the body panel
using three 6 x 12 mm washer-bolts.
HOLES (3)
4 mm
FLANGE NUTS (4)
REAR
UNIT
BRACKET
RECEIVER
UNIT
3213040B
6 x 12 mm
WASHER-BOLTS (3)
4 x 8 mm
WASHER- SCREWS (4)
3214011B
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 25222 (0307)
17 of 20
64. Bundle up the excess DIN cable, then secure the
DIN cable, the XM radio harness, and the antenna
cable with two wire ties with clips to the trunk side
panel.
67. Install the fuse 5A provided into the No.33 slot of
the fuse box.
FUSE BOX
FUSE (5A)
DIN CABLE
WIRE TIE WITH
CLIPS (2)
TRUNK SIDE
PANEL
2219080T
3218020B
65. Attach one cushion tape to the edge of the body
panel in the area shown. Inside the fender area
bundle up the excess antenna cable and secure
the antenna cable with one wire tie with clip.
EPT SEAL
68. Attach the fuse label 5A over the No.33 on the
back of the fuse box cover.
FUSE LABEL (5A)
ANTENNA
CABLE
REAR UNIT
BRACKET HOLE
FUSE BOX COVER
ANTENNA
CABLE
No.33
WIRE
TIE
WITH
CLIP
2219090T
69. Reinstall the rear console removed in step 7.
CUSHION
TAPE
18 of 20
3213051B
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
70. Remove the two nuts from the amplifier.
With Ashtray Holder:
SELF-TAPPING
SCREW (Reuse.)
LOWER PLAYER
BRACKET
VEHICLE CONNECTOR
VEHICLE CLIP
AMPLIFIER UNIT
NUT
(Reuse.)
CIGARETTE
LIGHTER
HARNESS
2-PIN
CONNECTOR
ASHTRAY
HOLDER
ILLUMINATION BULB
STUD
3305011S
2N02030S
71. Install the lower player bracket to the amplifier,
and reinstall the two nuts. Tighten the nuts
securely.
73. Bundle up the excess display module cable, and
secure the cable to the lower player bracket with
one wire tie with clip.
72. Install the coin pocket holder or ashtray holder.
LOWER PLAYER
BRACKET
DISPLAY
MODULE
CABLE
With Coin Pocket Holder:
SELF-TAPPING
SCREW
(Reuse.)
LEFT PLAYER
BRACKET
CLIP
STUD
WIRE TIE
WITH CLIP
STUD
STUD
COIN
POCKET
HOLDER
VEHICLE
CONNECTOR
6 mm
FLANGE
NUTS (4)
3214020B
2N03011S
RIGHT PLAYER
BRACKET
74. Insert the studs of the right upper, left upper, and
lower player brackets into the holes of the right
and left player brackets. Install and tighten the
four 6 mm flange nuts.
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 25222 (0307)
19 of 20
75. Check that all wire harnesses and cables are
routed properly and that all connectors are
plugged in.
76. If equipped with a cargo net, reinstall the right
trunk side trim and cargo net.
77. Check the operation of the XM radio system
according to the Owner’s Manual supplied.
78. Reinstall all removed parts. Check that all clips
and all other fasteners are installed securely.
79. Reconnect the negative cable to the battery.
80. Enter the customer’s radio anti-theft code, and
reset the radio station presets.
81. Reset the clock.
NOTE: Whenever the battery is disconnected, the
driver’s AUTO function is disabled.
82. Start the engine. Push down on the driver’s
window switch until the window is fully open.
83. Pull up on the driver’s window switch to close the
window completely, then hold the switch for
2 seconds.
84. Test the AUTO window function.
20 of 20
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement