INSTALLATION
INSTRUCTIONS
PARTS LIST
XM Radio Attachment (sold separately):
P/N 08B15-SEC-200
DIN cable
Accessory
XM RADIO SYSTEM
Application
2004 TSX
Display module pocket
Clip nut
XM radio harness
3 Self-tapping screws
Fastener
Front unit bracket
6 Washer-screws, 4 x 8 mm
Rear unit bracket
6 Washer-bolts, 6 x 12 mm
Bracket A
29 Wire ties
Bracket B
Bracket C
Double-sided adhesive tape
4 Flange nuts, 4 mm
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
Connector clip
5 Wire tie with clips
2 Cushion tapes
3 EPT seals
Fuse label
Mini fuse, 5 A
BII 25222 (0307)
Publications No.
BII 25222
Issue Date
JULY 2003
1 of 20
Attachment Kit (sold separately):
P/N 08B06-SEC-210
Right upper player bracket
Left upper player bracket
Lower player bracket
Right player bracket
Left player bracket
Player panel
BUS cable (not used)
2 Wire ties
2 of 20
Wire tie with clip
8 Flange nuts, 6 mm
2 Latches
Cushion tape
XM Antenna (sold separately):
P/N 08A15-1E1-100
Antenna
Unit Kit (sold separately):
P/N 08A15-1E1- 000
Display Module
FM modulator unit
Receiver unit
Owner’s Manual
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
TOOL AND SUPPLIES REQUIRED
Phillips screwdriver
Stubby Phillips screwdriver
Flat-tip screwdriver
Hook tool
Isopropyl alcohol
Shop towel
Tape measure
Utility knife
Ratchet
8 mm and 10 mm Sockets
Felt-tip pen
Scissors
Drill
7 mm Drill bit
Illustration of the XM Radio System Installed on the
Vehicle
DISPLAY MODULE
RECEIVER
UNIT
ANTENNA
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
1.
Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons.
2.
Disconnect the negative cable from the battery.
3.
Remove the trim ring.
M/T Model:
• Pull up on the parking brake lever to prevent the vehicle from moving.
• Loosen the lock nut and remove the shift knob by turning it counterclockwise.
• Remove the lock nut.
SHIFT
KNOB
FM MODULATOR
UNIT
3211010B
VEHICLE
ANTENNA
CABLE
FM MODULATOR
UNIT
DISPLAY
MODULE
FUSE BOX
6-PIN CONNECTOR
XM RADIO
HARNESS
ANTENNA
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
DIN CABLE
RECEIVER UNIT
2N28010M
BII 25222 (0307)
LOCK
NUT
2031021S
3 of 20
4 of 20
• Gently pry up on the trim ring to release the eight clips.
• Unplug the two seat heater connectors, and remove the trim ring.
CLIPS (8)
TRIM
RING
4.
Open the pocket lid. Pull the pocket out toward you to release the four clips, unplug the illumination bulb, and remove the pocket. Take care not to damage the illumination bulb.
ILLUMINATION
BULB
CLIP
LID
POCKET
SEAT HEATER
CONNECTOR
2031030S
A/T Model:
• Pull up on the parking brake lever to prevent the vehicle from moving.
• Move the shift lever into Neutral.
• Gently pry up on the trim ring to release the eight clips.
• Unplug the two seat heater connectors and remove the trim ring.
CLIPS (8)
TRIM
RING
2031051S
CLIPS (4)
5.
Remove the coin pocket holder or ashtray holder.
With Coin Pocket Holder:
• Remove the four self-tapping screws.
• Gently pull out the coin pocket holder to release the clip from the coin pocket holder and unplug the vehicle connector. Remove the coin pocket holder.
SELF-TAPPING
SCREW
(Reuse.)
CLIP
SEAT HEATER
CONNECTOR
2031040S
BII 25222 (0307)
COIN
POCKET
HOLDER
VEHICLE
CONNECTOR
2N03011S
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
With Ashtray Holder:
• Remove the four self-tapping screws.
• Gently pull out the ashtray holder, unplug the illumination bulb, vehicle connector and cigarette lighter harness 2-pin connector.
Remove the ashtray holder.
SELF-TAPPING
SCREW (Reuse.)
VEHICLE CONNECTOR
VEHICLE CLIP
7.
Remove the rear console.
• Open the lid and remove the rear console mat from inside of the rear console.
• Remove the two screws and the four selftapping screws, and unplug the connector and harness clip.
REAR
CONSOLE MAT
LID
SELF-TAPPING
SCREWS (4)
REAR
CONSOLE
ASHTRAY
HOLDER
ILLUMINATION BULB
CIGARETTE
LIGHTER
HARNESS
2-PIN
CONNECTOR
3305011S
6.
Remove the illumination bulb, and attach the electrical tape as shown. Bundle any excess illumination bulb harness, and secure it to the vehicle harness with one wire tie.
ELECTRICAL TAPE
WIRE TIE
ILLUMINATION
BULB
(Remove.)
VEHICLE
HARNESS
SCREWS
(2)
HARNESS CLIP
CONNECTOR
2N01030Y
8.
Remove the driver's dashboard lower cover (one self-tapping screw, retaining clip and two hooks).
HOOKS (2)
ILLUMINATION
BULB HARNESS
RETAINING
CLIP
DASHBOARD
LOWER COVER
SELF-TAPPING
SCREW
2N01080Y
2N21112S
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 25222 (0307)
5 of 20
9.
Remove the driver's dashboard under cover
(release the three clips, tab, and pin).
CLIP
11. Remove the passenger's dashboard under cover
(release the three clips, one tab, and three pins).
PINS (3)
TAB
DASHBOARD
UNDER COVER
PIN
2N19010S
10. Remove the left side console cover. Remove the self-taping screw, clip, and release the three retaining clips.
SCREW
CLIPS (3)
TAB
12. Remove the glove box (two stops, damper rod, and two bolts).
STOPS (2)
DAMPER
ROD
CLIP
CONSOLE
COVER
CLIPS (3)
GLOVE BOX
BOLTS (2)
3211081B
6 of 20
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
Installing the XM Radio Harness and FM Modulator
Unit
13. Attach the fuse labels to the fuse cases on the
XM radio harness.
FUSE LABEL
When attaching the fuse labels to the fuse cases, open the fuse case cover and make sure that the fuse is in the case.
If the vehicle is equipped with other accessories:
• Unplug the other accessory harness 6-pin connector from the fuse box.
• Remove the dummy connector from the XM radio harness.
• Plug the XM radio harness 6-pin connector into the fuse box 6-pin connector, then plug the other accessory 6-pin connector into the XM radio harness 6-pin connector.
6-PIN
CONNECTOR
3121030M
Use these labels.
FUSE BOX
6-PIN
CONNECTOR
FUSE
CASES
OTHER
ACCESSORY
6-PIN
HARNESS
FUSE
LABEL
2A
LABEL
5A
LABEL
CLIP
XM
RADIO
HARNESS
2524051M
14. On the fuse box, locate the 6-pin connector. Plug the XM radio harness 6-pin connector into the fuse box 6-pin connector.
XM RADIO HARNESS
6-PIN CONNECTOR
DUMMY
CONNECTOR
(Discard.)
2524060M
15. Install the fuse cases and the dummy 6-pin connector from the XM radio harness to the fuse box case.
FUSE CASE
POSITION
ON THE
FUSE BOX
CASE
FUSE
CASES
VEHICLE
HARNESS
WIRE TIE
XM RADIO
HARNESS
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
3226030B
XM RADIO HARNESS 6-PIN CONNECTOR
WITH DUMMY CONNECTOR
(Do not secure to the yellow SRS harness.)
16. Secure the XM radio harness to the vehicle harness with the wire tie.
BII 25222 (0307)
7 of 20
17. Route the XM radio harness under the steering shaft and on the inside of the center console.
VEHICLE
HARNESS
20. Locate the welded nut on the vehicle stay.
Remove the vehicle ground bolt, and attach the ground terminal of the XM radio harness with the removed bolt.
VEHICLE GROUND
TERMINAL
GROUND
TERMINAL
VEHICLE
GROUND
BOLT
WIRE
TIES (3)
3218010B
XM RADIO
HARNESS
18. Loosely secure the XM radio harness to the vehicle harness with three wire ties.
19. Using a hook tool, pull out on the driver's instrument side trim to release the three clips, and unplug the vehicle connector and the hose.
Remove the side trim.
HOSE
HOOK
TOOL
VEHICLE
CONNECTOR
XM RADIO
HARNESS
3-PIN
CONNECTOR
3211020B
XM RADIO
HARNESS
21. Route the XM radio harness 3-pin connector toward the glove box opening.
22. In the glove box opening, locate the frame stay pipe. Align the holes in the frame stay pipe with the welded nuts in the bracket A, and loosely attach bracket A to the pipe frame with the two
6 x 12 mm washer-bolts.
PIPE FRAME
STAY
BRACKET A
6 x 12 mm
WASHER-BOLT
Pull out.
3123011B
CLIPS (3)
DRIVER'S
INSTRUMENT
SIDE TRIM
6 x 12 mm
WASHER BOLT
3211090B
8 of 20
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
23. Attach the connector clip to the harness connector of the FM modulator unit. Attach bracket B to the
FM modulator unit with one 4 x 8 mm washerscrew. Tighten the washer-screw securely.
25. Below the glove box opening, remove the upper heater blower case mounting bolt.
BRACKET B
4 x 8 mm
WASHER-
SCREW
CONNECTOR
CLIP
FM
MODULATOR
UNIT
2524121M
24. Attach bracket B with the FM modulator unit against bracket A, and install one additional
6 x 12 mm washer-bolt. Tighten all three
6 x 12 mm washer-bolts securely.
BRACKET A
BOLT
(Reuse.)
HEATER
BLOWER CASE
3212040B
26. Attach the bracket C to the bottom of the FM modulator unit with one 4 x 8 mm washer-screw and the vehicle bolt removed in step 25.
27. On the back of the FM modulator unit, attach one wire tie with clip to the antenna harnesses, and attach the wire tie with clip to the hole in bracket C.
FM
MODULATOR
UNIT
HARNESS
WIRE TIE
WITH CLIP
FM
MODULATOR
UNIT
6 x 12 mm
WASHER-BOLT
BRACKET B
3211100B
BRACKET C
4 x 8 mm
WASHER SCREW
VEHICLE
BOLT
(reused)
FM MODULATOR
UNIT ANTENNA
HARNESS
3212050B
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 25222 (0307)
9 of 20
28. Connect the XM radio harness 3-pin connector to the FM modulator unit harness 3-pin connector, then attach the 3-pin connector clip to the hole in bracket B.
BRACKET B
XM RADIO
HARNESS 3-PIN
CONNECTOR
Installing the Display Module
29. Slide the clip nut onto the display module pocket flange.
DISPLAY MODULE
POCKET FLANGE
CLIP
Clean with isopropyl alcohol.
FM MODULATOR
UNIT HARNESS 3-PIN
CONNECTOR
3212110B
DISPLAY MODULE
POCKET
DISPLAY
MODULE
3121040M
BACKING
DOUBLE-SIDED
ADHESIVE TAPE
Clean with isopropyl alcohol.
30. Using isopropyl alcohol on a shop towel, clean the bonding surface on the display module and display module pocket.
31. Remove the adhesive backing from the doubleface adhesive tape, then attach it to the display module back. Remove the adhesive backing from the double-face adhesive tape on the display module.
32. Route the display module cable through the hole of the display module pocket. Attach the display module to the display module pocket while pulling the display module cable.
10 of 20
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
33. Install one latch to each player bracket.
LEFT PLAYER
BRACKET
RIGHT PLAYER
BRACKET
36. Plug the DIN cable and display module cable into the FM modulator unit. Route the FM modulator unit antenna harness along the DIN cable and on the inside of the front console.
DISPLAY
MODULE
CABLE
FM MODULATOR UNIT
LATCH
LATCH
SELF-
TAPPING
SCREWS (3)
3211030B
DISPLAY MODULE
POCKET
34. Assemble the display module pocket with the left player bracket and right player bracket with the three self-tapping screws.
35. Route the DIN cable and display module cable along the XM radio harness (3-pin connector side) to the FM modulator unit.
DIN
CABLE
FM
MODULATOR
UNIT ANTENNA
HARNESS
DIN CABLE
3212120B
37. Unplug the vehicle antenna cable, and plug it into the FM modulator unit antenna cable. Plug the other FM module antenna jack into the vehicle antenna cable.
XM RADIO
HARNESS
WIRE TIE
DIN CABLE/DISPLAY
MODULE CABLE
WIRE TIE
To the FM modulator unit
DISPLAY
MODULE CABLE
3211040B
FM
MODULATOR
ANTENNA
JACK
EPT
SEAL
DISPLAY
MODULE
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
3211050B
VEHICLE
ANTENNA JACK
38. Wrap one EPT seal around the antenna jack, and secure the antenna jack to the vehicle antenna jack with one wire tie. Secure the DIN cable, the display module cable, and the antenna harness to the vehicle harness with one wire tie.
BII 25222 (0307)
11 of 20
39. Secure the XM radio harness to the vehicle harness with two wire ties. Bundle up the excess display module cable, and secure it with one wire tie.
WIRE TIES (2)
XM RADIO
HARNESS
VEHICLE
HARNESS
Routing the XM Radio Harness, DIN Cable and
Antenna cable
41. Inside the passenger compartment, remove the rear seat cushion by removing the bolt and releasing the two hooks (pull the hook out toward you).
REAR SEAT
CUSHION
BOLT
3211060B
40. Insert the studs from the right and left upper player brackets into the holes in the vehicle frame.
Install the 6 mm flange nuts on the end of each stud, and tighten the flange nuts securely. Set the display module assembly aside; it will be installed later.
6 mm
LEFT UPPER
PLAYER
BRACKET
3212011B
HOOKS (2)
42. Remove the right side cushion by removing one bolt and one hook.
HOOK
CUSHION
STUDS (2)
RIGHT UPPER
PLAYER
BRACKET
STUDS (2)
6 mm
FLANGE
NUT
2N02041S
BOLT
3212020B
12 of 20
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
43. Fold down each rear seat back by pulling the lever under the rear parcel shelf inside the trunk.
REAR SEAT
BACKS (2)
45. Remove the rear trim panel (four clips).
REAR TRIM PANEL
Down
Pull.
Down
TRUNK WEATHERSTRIP
CLIPS (4)
2325010T
LEVERS (2)
44. Remove the spare tire cover (one clip).
CLIP
3212030B
If the vehicle is not equipped with a cargo net, go to step 51; otherwise, go to step 46.
46. Remove the cargo net from the "A" and "B" hooks on the right trunk side trim. Then remove the "A" and "B" hooks.
"A" AND "B" HOOKS (4)
RUBBER
STRAPS
(4)
CARGO NET
SPRING
WASHER
SPARE TIRE COVER
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
2322010T
HOOK "A"
HOOK "B"
RIGHT TRUNK
SIDE TRIM
BII 25222 (0307)
13 of 20
47. Remove the right trunk side trim (four clips). Take care not to damage the clips and retaining clips.
RIGHT TRUNK
SIDE TRIM
TRUNK TRIM
RETAINING
CLIP
49. Measure and mark the rear unit bracket using a felt-tip pen as shown. While wearing eye protection, drill a 7 mm hole through the mark in the rear unit bracket.
Remove.
CLIPS (4)
3211071B
48. Remove the upper flange nut, long collar and washer, then remove the 40 mm bolt, washer and spring washer.
WASHER
ELONGATED
HOLE
19.5 mm
7 mm
DRILL
WASHER
COLLAR
(LONG)
62.5 mm
WASHER
40 mm
BOLT
SPRING
WASHER
FLANGE
NUT
50. Insert the 40 mm bolt with washers through the
7 mm drilled hole.
51. Route the XM radio harness and the DIN cable along the vehicle harness toward the parking brake lever. Secure the harness and DIN cable to the vehicle harness with five wire ties in the areas shown.
VEHICLE
HARNESS
RIGHT TRUNK
SIDE PANEL
FLANGE NUT
LONG
COLLAR
14 of 20
WIRE TIES (5)
XM RADIO
HARNESS
AND DIN
CABLE
2527072M
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
52. Raise the rear seat back. Pull the DIN cable and
XM radio harness out from under the floor carpet and toward the passenger's side of the vehicle.
Secure the XM radio harness and DIN cable to the vehicle harness with seven wire ties.
54. Inside the trunk, unplug the vehicle harness connector from the brake light case. Release the four hooks of the brakelight case from the parcel shelf, and remove the brake light case.
BRAKE LIGHT CASE
XM RADIO
HARNESS
AND DIN
CABLE
VEHICLE
HARNESS
VEHICLE
HARNESS
CLIP
HOOKS (4)
PARCEL SHELF
CONNECTOR
2527060M
WIRE
TIES (7)
3212091B
53. Route the XM radio harness and DIN cable along the vehicle harness toward the trunk. Secure the
XM radio harness and DIN cable to the vehicle harness with two additional wire ties.
WIRE TIE (2)
DIN
CABLE
XM RADIO
HARNESS
3212100B
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 25222 (0307)
15 of 20
55. Using isopropyl alcohol on a shop towel, clean the bottom of the antenna. Remove the adhesive backing from the fastener, and attach the fastener to the bottom of the antenna.
CUSHION
TAPE
ANTENNA
Clean with isopropyl alcohol.
58. Measure and mark the cutting area on the brake light case. Using a utility knife, cut out the brake light case in the area shown. Remove any burrs from the edges of the groove. Route the antenna cable through the case groove and install the brake light case.
BRAKE LIGHT
CASE
Cut.
REAR TRAY
3212061B
FASTENER
56. Route the antenna cable through the high-mount brake light opening, and install the antenna to the rear tray in the area shown. Attach one cushion tape to the edge of the rear parcel shelf where the antenna cable touches.
57. Align the antenna cable on the rear tray with the brake light case, then using a felt-tip pen, mark the cable position on the edge of the case.
ADHESIVE
BACKING
20 mm
10 mm
5 mm
MARK
5 mm
10 mm
59. Route the antenna cable along the vehicle harness, and secure the antenna cable to the vehicle harness with five wire ties in the areas shown.
3212071B
VEHICLE
HARNESS
NAVIGATION UNIT
(if equipped)
MARK
ANTENNA
CABLE
FELT-TIP PEN
BRAKE LIGHT
CASE
REAR
TRAY
WIRE TIE
ANTENNA
CABLE
3213011B
Align.
3212081B
16 of 20
ANTENNA
CABLE
Straight.
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
60. Secure the antenna cable, the DIN cable, and the
XM radio harness to the vehicle harness with two wire ties.
62. Position the receiver unit between the right trunk side panel and rear fender panel, and plug in the antenna cable connectors, the DIN cable connector, and the XM radio harness connector to the receiver unit.
ANTENNA
CABLE
XM RADIO
HARNESS
DIN CABLE
RECEIVER
UNIT
VEHICLE
HARNESS
XM RADIO
HARNESS
WIRE TIE (2)
DIN CABLE
ANTENNA
CABLE
3213020B
61. Install the front and rear unit brackets to the receiver unit using two 4 x 8 mm washer-screws and two 4 mm flange nuts for each bracket. If equipped with a cargo net, make sure the 40 mm bolt and washers are in place.
REAR
FENDER
PANEL
3213030B
RIGHT TRUNK
SIDE PANEL
63. Attach the receiver unit/brackets to the body panel using three 6 x 12 mm washer-bolts.
HOLES (3)
FRONT UNIT
BRACKET
4 mm
FLANGE NUTS (4)
RECEIVER
UNIT
REAR
UNIT
BRACKET
4 x 8 mm
WASHER- SCREWS (4)
3214011B
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 25222 (0307)
6 x 12 mm
WASHER-BOLTS (3)
3213040B
17 of 20
64. Bundle up the excess DIN cable, then secure the
DIN cable, the XM radio harness, and the antenna cable with two wire ties with clips to the trunk side panel.
DIN CABLE
67. Install the fuse 5A provided into the No.33 slot of the fuse box.
FUSE BOX
FUSE (5A)
WIRE TIE WITH
CLIPS (2)
TRUNK SIDE
PANEL
3218020B
65. Attach one cushion tape to the edge of the body panel in the area shown. Inside the fender area bundle up the excess antenna cable and secure the antenna cable with one wire tie with clip.
ANTENNA
CABLE
EPT SEAL
REAR UNIT
BRACKET HOLE
2219080T
68. Attach the fuse label 5A over the No.33 on the back of the fuse box cover.
FUSE LABEL (5A)
FUSE BOX COVER
CUSHION
TAPE
ANTENNA
CABLE
WIRE
TIE
WITH
CLIP
3213051B
No.33
2219090T
69. Reinstall the rear console removed in step 7.
18 of 20
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
70. Remove the two nuts from the amplifier.
LOWER PLAYER
BRACKET
AMPLIFIER UNIT
With Ashtray Holder:
SELF-TAPPING
SCREW (Reuse.)
VEHICLE CONNECTOR
VEHICLE CLIP
NUT
(Reuse.)
STUD
2N02030S
71. Install the lower player bracket to the amplifier, and reinstall the two nuts. Tighten the nuts securely.
72. Install the coin pocket holder or ashtray holder.
With Coin Pocket Holder:
SELF-TAPPING
SCREW
(Reuse.)
CLIP
COIN
POCKET
HOLDER
VEHICLE
CONNECTOR
2N03011S
ASHTRAY
HOLDER
ILLUMINATION BULB
CIGARETTE
LIGHTER
HARNESS
2-PIN
CONNECTOR
3305011S
73. Bundle up the excess display module cable, and secure the cable to the lower player bracket with one wire tie with clip.
LOWER PLAYER
BRACKET
DISPLAY
MODULE
CABLE
LEFT PLAYER
BRACKET
STUD
WIRE TIE
WITH CLIP
STUD
STUD
6 mm
FLANGE
NUTS (4)
3214020B
RIGHT PLAYER
BRACKET
74. Insert the studs of the right upper, left upper, and lower player brackets into the holes of the right and left player brackets. Install and tighten the four 6 mm flange nuts.
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 25222 (0307)
19 of 20
75. Check that all wire harnesses and cables are routed properly and that all connectors are plugged in.
76. If equipped with a cargo net, reinstall the right trunk side trim and cargo net.
77. Check the operation of the XM radio system according to the Owner’s Manual supplied.
78. Reinstall all removed parts. Check that all clips and all other fasteners are installed securely.
79. Reconnect the negative cable to the battery.
80. Enter the customer’s radio anti-theft code, and reset the radio station presets.
81. Reset the clock.
NOTE: Whenever the battery is disconnected, the driver’s AUTO function is disabled.
82. Start the engine. Push down on the driver’s window switch until the window is fully open.
83. Pull up on the driver’s window switch to close the window completely, then hold the switch for
2 seconds.
84. Test the AUTO window function.
20 of 20
BII 25222 (0307)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
