Moxa Technologies | UPORT 1100 series | User`s manual | Moxa Technologies UPORT 1100 series User`s manual

Moxa Technologies UPORT 1100 series User`s manual
UPort 1110 and 1130 User’s Manual
First Edition, August 2006
www.moxa.com/product
MOXA Technologies Co., Ltd.
Tel:
+886-2-8919-1230
Fax: +886-2-8919-1231
Web: www.moxa.com
MOXA Technical Support
support@moxa.com
Worldwide:
UPort 1110 and 1130 User’s Manual
The software described in this manual is furnished under a license agreement and may be used only in
accordance with the terms of that agreement.
Copyright Notice
Copyright © 2006 MOXA Technologies Co., Ltd.
All rights reserved.
Reproduction without permission is prohibited.
Trademarks
MOXA is a registered trademark of The MOXA Group.
All other trademarks or registered marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not represent a commitment on the
part of MOXA.
MOXA provides this document “as is,” without warranty of any kind, either expressed or implied, including, but
not limited to, its particular purpose. MOXA reserves the right to make improvements and/or changes to this
manual, or to the products and/or the programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. However, MOXA assumes no
responsibility for its use or for any infringements on the rights of third parties that may result from its use.
This product may include unintentional technical or typographical errors. Changes are periodically made to the
information herein to correct such errors, and these changes are incorporated into new editions of the
publication.
Table of Contents
Chapter 1
Introduction ...............................................................................................1-1
Overview .............................................................................................................................. 1-2
Package Checklist................................................................................................................. 1-2
Product Features ................................................................................................................... 1-2
Product Specifications .......................................................................................................... 1-3
LED Indicators ..................................................................................................................... 1-4
Chapter 2
Installation and Configuration .................................................................2-1
Initial Driver Installation ...................................................................................................... 2-2
Hardware Installation ........................................................................................................... 2-5
Windows 98 and Windows 2000 .................................................................................. 2-5
Windows XP and Windows 2003................................................................................. 2-6
Configuring the COM Port ................................................................................................. 2-12
Configuring the Adaptor..................................................................................................... 2-13
Removing the Adaptor........................................................................................................ 2-15
Uninstalling the Driver ....................................................................................................... 2-16
Appendix A.
Pin Assignments ...................................................................................... A-1
UPort DB9 Pin Assignments ............................................................................................... A-1
Terminal Block Pin Assignments......................................................................................... A-1
Appendix B.
Service Information.................................................................................. B-1
MOXA Internet Services ......................................................................................................B-2
Technical Support E-mail Address ...............................................................................B-2
Website for Product Information ..................................................................................B-2
Problem Report Form ...........................................................................................................B-3
Product Return Procedure.....................................................................................................B-4
1
Chapter 1
Introduction
The UPort 1110 and the UPort 1130 are USB-to-serial adaptors, an easy way to add a COM port to
your system. The UPort 1110 provides one RS-232 port and the UPort 1130 provides one
RS-422/RS-485 port. As a plug and play USB device, the adaptors are perfect for mobile,
instrumentation, and point-of sale applications.
The following topics are covered in this chapter:
‰
‰
‰
‰
‰
Overview
Package Checklist
Product Features
Product Specifications
LED Indicators
UPort 1110 and 1130 User’s Manual
Introduction
Overview
The UPort 1110 and UPort 1130 are part of Moxa’s UPort line of USB-to-serial adaptors. The
UPort line provides a range of easy-to-use solutions for adding COM ports through a PC’s USB
port. Simply install the drivers, connect the UPort to your computer, plug in your serial devices,
and you’re ready to go. Programming is not required, and you do not need to worry about IRQs,
configuring a board, power requirements, or connection schemes.
The UPort 1110 and UPort 1130 provide single COM port expansion. The UPort 1110 adds one
RS-232 port to your computer, which is the same type of COM port that is built into most PC
motherboards. The UPort 1130 adds one port that is configurable for RS-422, 2-wire RS-485, and
4-wire RS-485 modes. Both models can operate at speeds of up to 12 Mbps, which is much faster
than the current maximum serial transfer rate.
The adaptor is bus-powered, so no external power supply is required.
Package Checklist
The following items are included in your UPort package:
y
y
y
y
UPort 1110 or UPort 1130 USB-to-Serial Adaptor
UPort Documentation and Software CD
UPort 1110/1130 Quick Installation Guide
5-year Warranty Statement
The UPort 1130 also comes with the following item:
y
Mini DB9F-to-Terminal-Block Converter
NOTE: Notify your sales representative if any of the above items is missing or damaged.
Product Features
The UPort adaptor has the following features:
y
y
y
y
y
y
y
Full-Speed USB operation at up to 12 Mbps
Additional I/O or IRQ not required
Serial transmission speed up to 921.6 Kbps
64-byte FIFO and built-in hardware and software flow control
Built-in 15 KV ESD protection
Support for RS-422, 2-wire RS-485, and 4-wire RS-485 (UPort 1130 only)
Terminal block adaptor (UPort 1130 only)
1-2
UPort 1110 and 1130 User’s Manual
Introduction
Product Specifications
USB
Version
Connector
Speed
Serial Interface
No. of Ports
RS-232 (UPort 1110)
RS-422 (UPort 1130)
RS-485 (UPort 1130)
USB 1.1 (also compatible with USB 1.0 and 2.0)
USB type B
12 Mbps
1
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
TxD+(B), TxD-(A), RxD+(B), RxD-(A),GND
4-wire: TxD+(B), TxD-(A), RxD+(B), RxD-(A), GND
2-wire: Data+(B), Data-(A), GND
Connector
Male DB9
FIFO
64 bytes
Serial line protection
15 KV ESD for all signals
Serial Communication Parameters
Parity
None, Even, Odd, Space, Mark
Data bits
5, 6, 7, 8
Stop bits
1, 1.5, 2
Flow control
RTS/CTS, XON/XOFF
Speed
50 bps to 921.6 Kbps
Power Requirements
Power Consumption
30 mA@5 VDC
Mechanical
Dimensions
37.5 x 20.5 x 60 mm (L x W x H)
Material
ABS + PC
Gross Weight
60 g (0.13 lb)
Environmental
Operating Temperature 0°C to 55°C (32°F to 131°F)
Storage Temperature
-20°C to 85°C (-4°F to 185°F)
Operating Humidity
5% RH to 95% RH
Regulatory Approvals
EN55022 Class B, EN55024, EN61000-3-2, EN61000-3-3, IEC
61000-4-2, IEC 61000-4-3, IEC 61000-4-4, IEC 61000-4-5, IEC
61000-4-8, FCC Part 15 Class B
Warranty
5 years
1-3
UPort 1110 and 1130 User’s Manual
Introduction
LED Indicators
UPort 1130
UPort 1110
Active
Active
TxD
TxD
RxD
RxD
1110
1130
RS-232
USB-to-Serial Adaptor
RS-422/485
USB-to-Serial Adaptor
Name
Description
Active
This LED indicates normal operation. If the driver is installed correctly and the
adaptor is plugged into a functioning USB port, the Active LED will light up
and remain on. If the LED does not light up, there may be a problem with the
adaptor, the driver installation, or PC configuration.
TxD
This LED blinks when the adaptor transmits data through its COM port.
RxD
This LED blinks when the adaptor receives data through its COM port.
1-4
2
Chapter 2
Installation and Configuration
Installation of the adaptor is a simple process. First install the driver, then plug the adaptor into a
USB port. When the adaptor is plugged in, Windows will load the correct drivers for the adaptor
and the new COM port. In this chapter, basic installation and configuration procedures are
explained. Although the installation screens will be for Windows 2000, the procedures are
essentially the same for Windows 98 and later versions.
The following topics are covered in this chapter:
‰
‰
Initial Driver Installation
Hardware Installation
¾
¾
‰
‰
‰
‰
Windows 98 and Windows 2000
Windows XP and Windows 2003
Configuring the COM Port
Configuring the Adaptor
Removing the Adaptor
Uninstalling the Driver
UPort 1110 and 1130 User’s Manual
Installation and Configuration
Initial Driver Installation
The Documentation and Software CD will contain the drivers for the adaptor. You may also
download the drivers at www.moxa.com. The installation procedure is the same for all Windows
operating systems.
Use Windows Explorer to locate the driver installation file, which will be Setup or Install.
On the Documentation and Software CD, this file will be located in the UPort 1100/Software
folder, filed by operating system. Double-click the Setup or Install file.
1.
The Setup Wizard will open. Click Next to begin installing the driver.
2-2
UPort 1110 and 1130 User’s Manual
Installation and Configuration
2.
Click Next to install the driver in the indicated folder, or use the drop-down folder list to
locate a different folder.
3.
Click Install to proceed with the installation.
2-3
UPort 1110 and 1130 User’s Manual
Installation and Configuration
4.
Wait while the driver is installed on your hard drive.
5.
A window will pop up cautioning you that this software has not passed Windows logo testing.
This is a standard warning, and Moxa has thoroughly tested the driver for safe Windows
operation. Please click Yes to proceed.
2-4
UPort 1110 and 1130 User’s Manual
6.
Installation and Configuration
Click Finish to complete the installation of the driver.
Hardware Installation
After installing the driver, plug the adaptor into any upstream USB port, such as a USB port on
your computer. Windows will automatically detect the adaptor and begin installing the driver.
When the Windows finishes installing the driver for the adaptor, it will then detect a new COM
port, and will then install another driver for the new COM port..
ATTENTION
For best results, we recommend that you install the driver before plugging the adaptor into the
USB port. Please refer to the previous section on Initial Driver Installation for instructions.
Windows 98 and Windows 2000
The following instructions are for Windows 98 and Windows 2000 systems:
1.
After plugging the adaptor into a USB port, the Found New Hardware window should open
automatically. The USB icon indicates that the USB port is being installed. No action is
required.
2-5
UPort 1110 and 1130 User’s Manual
Installation and Configuration
2.
Windows 98 users may skip to the next step. On Windows 2000 systems, a window will pop
up cautioning you that this software has not passed Windows logo testing. This is a standard
warning, and Moxa has thoroughly tested the driver for safe Windows operation. Please click
Yes to proceed.
3.
Windows will automatically detect and install the new serial port. No further action is
required
Windows XP and Windows 2003
The following instructions are for Windows XP and Windows 2003 systems.
1.
After plugging the adaptor into a USB port, Windows will automatically detect the new
device. The Found New Hardware balloon will appear in the bottom right corner of the
Windows desktop. No action is required yet.
2-6
UPort 1110 and 1130 User’s Manual
Installation and Configuration
2.
After a moment, the Found New Hardware Wizard will open. If you see the following screen,
select No, not this time, then click Next.
3.
On the next window that appears, select Install the software automatically
(Recommended), then click Next.
2-7
UPort 1110 and 1130 User’s Manual
Installation and Configuration
4.
The installation wizard will search for the correct drivers. After a moment, a window will pop
up cautioning you that this software has not passed Windows logo testing. This is a standard
warning, and Moxa has thoroughly tested the driver for safe Windows operation. Please click
Continue Anyway to proceed.
5.
Windows will spend a few moments installing the UPort driver..
2-8
UPort 1110 and 1130 User’s Manual
Installation and Configuration
6.
The next window indicates that Windows has completed the installation. Click Finish to
continue with installation procedure.
7.
After Windows has completed installing the adaptor, it will automatically detect the new
COM port. The Found New Hardware balloon will appear in the bottom right corner of the
Windows desktop.
2-9
UPort 1110 and 1130 User’s Manual
Installation and Configuration
8.
After a moment, the Found New Hardware Wizard will open. Select Install the software
automatically (Recommended), then click Next.
9.
The installation wizard will search for the correct drivers. After a moment, a window will pop
up cautioning you that this software has not passed Windows logo testing. This is a standard
warning, and Moxa has thoroughly tested the driver for safe Windows operation. Please click
Continue Anyway to proceed.
2-10
UPort 1110 and 1130 User’s Manual
Installation and Configuration
10. Windows will spend a few moments installing the driver.
11. The next window indicates that Windows has completed the installation. Click Finish to
proceed with installation procedure.
12. The Found New Hardware balloon will reappear, indicating that the installation was
successful.
2-11
UPort 1110 and 1130 User’s Manual
Installation and Configuration
Configuring the COM Port
After the driver and hardware have been successfully installed, the new COM port will have a
COM number and can be accessed and controlled just like your PC’s built-in COM ports. If you
need to change the baud rate, parity, or other COM port settings, you may use your serial
communication application to make those changes. You may also go to Device Manager and
right-click the MOXA USB Serial Port, which will be listed under Ports along with your PC’s
built-in COM ports. In the context menu that pops up, you may select Properties in order to
modify the COM port settings.
2-12
UPort 1110 and 1130 User’s Manual
Installation and Configuration
Configuring the Adaptor
If you need to change the COM number that the adaptor assigns to the COM port, or adjust other
advanced settings, you may go to Device Manager and right-click the UPort adaptor, which will be
listed under Multi-port serial adaptors. In the context menu that pops up, you may select
Properties in order to modify the COM port settings.
In the Port Configuration tab, you will see the new COM port listed. Click Port Setting to
modify the COM number and other parameters.
2-13
UPort 1110 and 1130 User’s Manual
Installation and Configuration
ATTENTION
Before modifying these settings, make sure that you have closed any applications that may be
accessing the COM port, such as HyperTerminal.
You may change the Port Number and enable or disable the Fast Flush function. For the UPort
1130, you may also select between RS-422, 2-wire RS-485, and 4-wire RS-485 modes. Please note
that Auto Enumerating COM Number and Set the change to all ports are not available for this
model of UPort.
The Fast Flush function is specifically designed to handle Win32 PurgeComm() function calls and
is enabled by default. When Fast Flush is enabled, the driver will automatically clear the local
buffer when it receives a PurgeComm() command. When Fast Flush is disabled, the driver will
repeatedly query the adaptor until it verifies that there is no more data in the buffer. Disabling this
function can cause lower throughput for applications that use PurgeComm() heavily.
2-14
UPort 1110 and 1130 User’s Manual
Installation and Configuration
Removing the Adaptor
The adaptor is a plug and play device. No special procedures are required to remove the adaptor;
you may simply pull the adaptor out of the USB port. You should verify that no data is being
transmitted before removing the adaptor.
Removing the adaptor does not remove the drivers. The drivers remain in place so that the adaptor
can be automatically detected and installed if it is pluged back into the USB port.
The adaptor can also be uninstalled through the Device Manager, the same as other Windows
devices. Right-click the adaptor, which will be found under Multi-port serial adaptors, then
select Uninstall from the context menu.
2-15
UPort 1110 and 1130 User’s Manual
Installation and Configuration
Uninstalling the Driver
The UPort driver may be removed through Add/Remove Programs in the Windows Control Panel.
Click Remove next to MOXA UPort 1110/1130 Windows Driver Ver1.3.
2-16
UPort 1110 and 1130 User’s Manual
Installation and Configuration
2-17
A
Appendix A.
Pin Assignments
UPort DB9 Pin Assignments
The UPort 1110 and UPort 1130 use male DB9 connectors. Pin assignments are shown in the
following diagram:
UPort 1110
DB9 (male)
1
6
5
9
Pin
RS-232
1
2
3
4
5
6
7
8
DCD (in)
RxD (in)
TxD (out)
DTR (out)
GND
DSR (in)
RTS (out)
CTS (in)
UPort 1130
RS-422
2-wire RS-485
4-wire RS-485
TxD-(A)
TxD+(B)
RxD+(B)
Data+(B)
RxD-(A)
Data-(A)
GND
GND
-
Terminal Block Pin Assignments
The UPort 1130 comes with a DB9 to terminal block converter, with pin assignments as shown
below:
RS-422
2-wire RS-485
4-wire RS-485
1
TxD+(B)
2
TxD-(A)
3
RxD+(B)
Data+(B)
4
RxD-(A)
Data-(A)
5
GND
GND
Note that the converter maps pin 1 on the DB9 connector to pin 2 on the terminal block, and pin 2
on the DB9 connector to pin 1 on the terminal block.
Terminal Block
Pin
B
Appendix B.
Service Information
This appendix contains information on how to obtain information or service from MOXA for the
UPort adaptor and other MOXA products. The following topics are covered:
‰
MOXA Internet Services
¾
¾
‰
‰
Technical Support E-mail Address
Website for Product Information
Problem Report Form
Product Return Procedure
UPort 1110 and 1130 User’s Manual
Service Information
MOXA Internet Services
Customer satisfaction is our top priority. To ensure that customers receive the full benefit of our products,
MOXA Internet Services has been set up to provide technical support, driver updates, product information, and
user’s manual updates.
The following services are provided
Technical Support E-mail Address
support@moxa.com
Website for Product Information
http://www.moxa.com
B-2
UPort 1110 and 1130 User’s Manual
Service Information
Problem Report Form
MOXA UPort 1110 or UPort 1130
Customer name:
Company:
Tel:
Fax:
Email:
Date:
Select Product Model
‰
‰
UPort 1110
UPort 1130
Serial Number:____________________________________________________________________________
Problem Description
Please describe the symptoms of the problem as clearly as possible, including any error messages you see. A
clearly written description of the problem will allow us to reproduce the symptoms and expedite the repair of
your product.
B-3
UPort 1110 and 1130 User’s Manual
Service Information
Product Return Procedure
For product repair, exchange, or refund, the customer must:
y
y
y
y
Provide evidence of original purchase.
Obtain a Product Return Agreement (PRA) from the sales representative or dealer.
Fill out the Problem Report Form (PRF). Include as much detail as possible for a shorter
product repair time.
Carefully pack the product in an anti-static package and send it, pre-paid, to the dealer. The
PRA should be visible on the outside of the package and should include a description of the
problem along with the return address and telephone number.
B-4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising