TOA A-903MK2 Specification

TOA A-903MK2 Specification
TOA 900 MK2 SERIES
8-CHANNEL MIXER POWER
AMPLIFIER (30 WATT)
A-903MK2
DESCRIPTION
The TOA A-903MK2 Mixer Power Amplifier controls and
mixes up to eight independent input signals and delivers
up to 30 watts of output power. Optional plug-in
modules are available for use with the A-903MK2 to
provide a full range of operating applications. The use of
edge connectors on the rear of the unit permits selection
from a wide assortment of TOA plug-in modules.
A remote master volume control is provided, functioning
with an external potentiometer. A two-level muting
function is available with optional modules.
The A-903MK2 has output terminals to match 4- or
8-ohm speaker systems and 25- or 70-volt constant
voltage speaker distribution systems. An optional rack
mounting bracket is available.
FEATURES
1. Output power: 30 watts RMS
2. Wide frequency response: 20 to 20,000Hz ± 1 dB
3. Low distortion and noise level
4. Excellent output regulation
5. Bass and treble controls
6. Bridging input and output
7. Signal processing input and output
8. Remote master volume control
9. Built-in protection circuitry when heat sink temperature
overheats
10. Separate output terminals for 4 and 8 ohms, 25 and
70 volts constant voltage speaker distribution systems
11. Full range of plug-in modules
12. Mountable in two ElA standard rack units with optional
rack mounting bracket
SPECIFICATIONS
Type
8-channel mixer power amplifier
Output Power
Power Bandwidth
30 watts RMS
Frequency Response
(D) 20—20,000Hz, ± 1 dB (T) 20-15,000Hz, ± 1 dB
(T) 20—20,000Hz, +1dB/-3dB
Total Harmonic Distortion
0.02% at 1 kHz, rated output
Inputs
Eight input ports: Every port accepts any input
module
One bridging input/output
Input Sensitivity/Impedance
Input ports #1 to #8: 100mV/10k ohms
Bridging input/output: 100mV/3.3k ohms
Source Impedance
200 ohms with M-01/M-11/M-21/M-51/M-61 modules
(balanced Lo-Z microphone preamplifier)
50k ohms with M-03 module
(unbalanced Hi-Z microphone preamplifier)
R-01 module (mag phono preamplifier)
220k ohms with U-01/U-11/U-21/U-61 modules
(auxiliary preamplifier)
10k ohms with B-01/B-11 modules
(bridging transformer)
600 ohms with L-01/L-11/L-41 modules (line matching
transformer), I-01 module (paging input)
600 ohms (load impedance) with T-01 module
(line output)
Preamp Out/Power Amp In
1 ,000mV into 600 ohms/1 ,000mV, 10k ohms
Outputs
(T)= Transformer
(D)= Direct
(D) 20—20,000Hz, 0.5% THD
(T) 50—20,000Hz, 0.5% THD
Main (T): 4 ohms, 25 and 70 volts, balanced
Main (D): 8 ohms, unbalanced
Aux: 10k ohms, 1V
Output Regulation (1kHz)
(D): Less than 0.5dB, no load to full load
(T): Less than 1.0dB, no load to full load
Signal-to-Noise Ratio
(Band Pass: 20-20,000Hz)
With Tone Controls Centered
Master volume min : 90dB
Master volume max : 77dB
Power amplifier only: 105dB
Tone Controls
Bass: ± 10dB at 100Hz; Treble: ± 10dB at 10kHz
Controls
8 input gain controls
1 bass tone control
1 power ON/OFF switch
1 treble tone control
1 master gain control
1 tone defeat switch
1 low-cut switch (60Hz, 6dB/octave)
Indicators
1 power LED, 1 protect LED, 1 signal LED,
1 normal LED, 1 peak LED
Self-protection, with AC fuse (inside)
Connectors
Input #1 to #8: Card-edge connector
Bridging, Mixer preamp. output, Power amp. input,
Aux output: RCA phono jack
Output: Screw-terminal strip
Mute, Remote master VR: Screw-terminal strip
AC power cord/plug: SJT, 3-prong type
AC outlet: 3-pin grounding type
Power Consumption
60 watts
Temperature Range
12°F to 140°F (-10°C to +60°C)
16.5"(W) x 3.9"(H) x 12.5"(D) (420 x 99.1 x 318mm)
Dimensions
Weight
(without input modules)
Frequency Response
at 1/10 rated output (Direct output: 8-ohm load,
transformer output: 167-ohm load)
17.2lbs (7.8kg)
Color
Black
Standard Accessories
4 volume control covers (YA-920), 7 input port covers
Other Features
Output disconnected for approx 5 seconds after
switching power on
Optional Accessories
Plug-in modules
(see specifications for individual modules),
Rack mounting bracket model MB-25B
Specifications are subject to change without notice.
Power Output vs. Frequency
at 0.5% THD (Direct output: 8-ohm load,
transformer output: 167-ohm load)
Architect's and Engineer's Specifications
The mixer power amplifier shall have eight mixer input ports and shall be
capable of operation from a 120V, 50/60Hz line. Each input port shall be
usable with microphone, phono pickup or high-level devices. The amplifier
shall meet the following performance criteria. Power output shall be 30W at
less than 0.5% THD from 20 to 20,000Hz (direct output) or 50 to 20,000Hz
(transformer output). Frequency response shall be ± 1 dB from 20 to
20,000Hz (direct output) or 20 to 15,000Hz (transformer output).
Source impedance shall be 200/50K ohms with a microphone preamplifier,
50k ohms with a mag. phono preamplifier, 220k ohms with an auxiliary
preamplifier, 10k ohms with a bridging transformer, 600 ohms with a line
matching transformer and 600 ohms with a paging input. Load impedance
shall be 4, 8, 20.8 (25V line) or 163.3 (70V line) ohms. Load voltage shall be
11, 15.5, 25 or 70 volts.
Equivalent input noise shall be -126dBm with a Lo-Z microphone
preamplifier. Output noise shall be 90dB below rated output when all gain
controls are off.
TOA plug-in accessory modules designed for use with the A-903MK2 mixer
power amplifier shall utilize the latest in surface mount component
technology and include the following modules: the M Series microphone
preamplifiers available with muting, remote volume control, voice gate and
compressor options; the U series auxiliary preamplifiers available with
muting, remote volume control and compressor options; the R-01 magnetic
phono preamplifier; the B Series bridging transformers available with muting
option; the L Series line matching transformers available with muting option;
the S Series signal generator modules, and the I-01 TOA intercom system
interface paging module. Also available shall be the T-01 module featuring
600-ohm balanced output capability, and the T-02 module featuring auxiliary
input and balanced line output for music-on-hold.
The mixer power amplifier shall be rack mounted using the TOA MB-25B
rack mounting bracket. The amplifier's dimensions shall be 16.5"(W) x
3.9"(H) x12.5"(D) (420 x 99.1 x 318mm) and its weight shall be 17.2lbs.
(7.8kg). The mixer power amplifier shall be TOA model A-903MK2.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement