Blaupunkt | COBURG DJ A | Operating instructions | Blaupunkt COBURG DJ A Operating instructions

Blaupunkt COBURG DJ A Operating instructions
Radio / Cassette / Changer
Coburg RCM 127
Casablanca RCM 127
Cannes RCM 127
Woodstock DJ I
Woodstock DJ A
Operating instructions
Coburg ..RCM127 d
1
13.02.2001, 10:15 Uhr
17
18
14
15
16
13
12
11
Coburg
Woodstock
10
1
Casablanca
Cannes
Woodstock
2
3
5
4
7
6
11
2
3
4
8
9
Fernbedienung RC 06 (Option)
Remote control RC 06 (optional)
Télécommande RC 06 (en option)
Telecomando RC 06 (optional)
Afstandsbediening RC 06 (Optie)
Fjärrkontroll RC 06 (Tillval)
Mando a distancia RC 06 (opcional)
Telecomando RC 06 (opção)
2
Coburg ..RCM127 d
RCM 127
DJ I
2
13.02.2001, 10:15 Uhr
RCM 127
RCM 127
DJ A
Switching the audio source ........ 35
Radio operation with RDS ........... 36
AF - Alternative frequency .................... 36
REG - regional programme .................. 36
Selecting a waveband
(only Casablanca RCM 127,
Cannes RCM 127, Woodstock DJ A) ... 36
Station tuning ........................................ 37
Automatic tuning / ....................... 37
Manual tuning with << >> .................. 37
Receiving traffic programme
stations with RDS-EON................ 42
Traffic announcement priority on/off .... 42
Beep tone ............................................. 42
Switching off the beep tone ............... 42
Automatic seek tuning start .................. 42
CD changer operation .................. 45
Switching to the CD changer mode ...... 45
Selecting CDs and titles ....................... 45
MIX playback ........................................ 45
Selecting the display mode .................. 46
SCAN .................................................... 46
DSC programming ....................... 47
Overview of DSC factory settings ........ 49
27
DEUTSCH
ENGLISH
Appendix ....................................... 49
Specifications ........................................ 49
Blaupunkt telephone hotline ................. 49
27
Coburg ..RCM127 gb
FRANÇAIS
Putting the unit into operation .............. 34
Removing the KeyCard ........................ 34
“Training” a second KeyCard/
Replacing a KeyCard ............................ 34
Displaying the radio pass data ............. 34
Short Additional Memory (S.A.M.) ........ 35
Turn On Message (T.O.M.) .................. 35
Optical indication of anti-theft
protection .............................................. 35
Care of your KeyCard ........................... 35
Inserting a tape ..................................... 43
Removing a tape ................................... 43
Fast Forward/Rewind ........................... 43
Selecting titles with CPS ...................... 43
Switching the tape side (autoreverse) .. 44
Tape equalisation ................................. 44
Scanning cassette titles with SCAN ..... 44
Listening to the radio during
fast tape winding with RM .................... 44
Care notes ............................................ 44
ITALIANO
KeyCard theft protection system 34
Tape operation ............................. 43
NEDERLANDS
Precautions ........................................... 33
Traffic safety ......................................... 33
Installation ............................................. 33
Sound source mute .............................. 33
Accessories .......................................... 33
Adjusting the volume for traffic
announcements and the beep tone ...... 43
13.02.2001, 10:19 Uhr
ESPAÑOL
Important notes ............................ 33
Scrolling through the broadcasting
networks ................................................ 37
Changing the memory bank ................. 37
Storing stations ..................................... 37
Automatically storing the strongest
stations with Travelstore ....................... 38
Recalling stored stations ...................... 38
Scanning stored stations with
Preset Scan .......................................... 38
Scanning stations with Radio-Scan ...... 38
Selecting the seek tuning sensitivity .... 39
Switching from stereo to mono ............. 39
Loudness .............................................. 39
PTY – Programme-Type ....................... 39
Switching PTY on/off ......................... 39
Programme type ................................... 39
Checking the programme type of the
station ................................................ 40
Displaying the selected programme
type .................................................... 40
Selecting a programme type ............. 40
Storing programme types .................. 41
Scanning stations with PTY-SCAN ... 41
PTY priority ........................................ 41
PORTUGUÊS
Quick reference ............................ 28
SVENSKA
Contents
Quick reference
1 Switching on/off with the ON button:
Press ON.
When switching the set on with the ON
button, the KeyCard has to be inserted. The unit will play with the pre-adjusted volume.
Switching on/off with the KeyCard:
The set has to be turned on with the
ON button.
Note:
Read the information in chapter
“KeyCard theft protection system”.
Switching on/off via the ignition:
When connected correspondingly, the
set can also be turned on and off with
the vehicle ignition.
After the ignition has been switched
off, a double beep tone will remind you
that you should remove the KeyCard
before leaving your vehicle.
Switching on with the ignition being
switched off:
To keep on operating the set when the
ignition is switched off (KeyCard is inserted), proceed as follows:
Press ON. The unit will be turned on.
To avoid that the battery goes flat, the
system will be turned off automatically
after one hour of playback.
3
For instantly muting the volume.
button the volume
By pressing the
can be muted immediately. “MUTE”
will appear in the display.
The function is cancelled by pressing
button
or VOL+.
(mute)
When pressing VOL-, the
volume will be adopted.
To programme the mute volume level,
proceed as follows:
• Adjust the desired volume.
for 1 second until you
• Press
hear a beep.
Now this volume level is stored as your
mute volume.
2 VOL+ / VOLTo alter the volume.
Each time the set is switched on, it will
play with the pre-adjusted volume
(VOL FIX).
You may also change the VOL FIX setting (see chapter “DSC programming”).
28
Coburg ..RCM127 gb
28
13.02.2001, 10:19 Uhr
DEUTSCH
ENGLISH
5 Display
a
l
Down
Radio operation
Title selection
Station search
Up
Down
<</>> Up/Down in short intervals
(on FM only if AF is off)
On FM only:
<</>> To scroll through the station networks when AF is on, e.g.NDR 1, 2,
3, 4, N-JOY, FFN, ANTENNE ...
Tape operation
/
c
Upwards: Press briefly.
CUE - fast advance (audible):
Keep depressed.
Title selection (S-CPS)
Up
Down
Fast forward
Fast rewind
Stop function by pressing the opposite key.
Downwards: Press as many times
as required.
To re-start a title: Press briefly.
REVIEW - fast reverse (audible):
Keep depressed.
Extra rocker switch functions:
Further setting functions with
AUD
B
DSC Mode A
PTY
@
Condition: The corresponding function
is activated.
a) NDR1 NDS - Station name
b) TR 1
- Track (side) 1 of the cassette
c) 1 : 52
- Playback TIME or disc
NUMBER during CD
changer operation
d) FM
- Waveband
e) 5
- Preset button (1-6)
f) I, II, T
- Memory bank I, II or
Travelstore
g) lo
- Seek tuning sensitivity
h) AF
- Alternative frequency for
RDS operation
i) TP
- A traffic station is being
received
j) TA
- Priority for traffic stations
k) LD
- Loudness
l) PTY
- Programme type function
29
Coburg ..RCM127 gb
29
13.02.2001, 10:19 Uhr
ITALIANO
b
Up
/
FRANÇAIS
CD selection
NEDERLANDS
efg h i j k
SVENSKA
d
ESPAÑOL
Changer operation
Optional:
Coburg RCM 127, Casablanca
RCM 127, Cannes RCM 127
Included in scope of delivery:
Woodstock DJ I, Woodstock DJ A
PORTUGUÊS
4 Rocker switch
6 KeyCard theft protection system
To operate the set it is necessary that
the KeyCard is inserted.
KeyCard
Inserting the KeyCard
With the KeyCard tongue sticking out
of the unit, introduce the KeyCard into
the slot with the contact area showing up.
To remove the card, press first to unlock.
Read also the information in chapter
“KeyCard theft protection system”.
Flashing KeyCard tongue
When the radio is turned off and the
KeyCard removed, the KeyCard
tongue can be programmed to flash
for optical theft protection.
For more information see chapter
“DSC programming”.
This flashlight can be switched off by
pushing in the tongue and lock.
“WRONG KC” will briefly appear
on the display and the set will switch
off automatically.
7 FMT (Coburg RCM 127,
Woodstock DJ I)
BND (Casablanca RCM 127,
Cannes RCM 127, Woodstock DJ A)
For selection of the FM memory banks
I, II and T (Travelstore).
To switch over:
Press button repeatedly.
The selected memory bank will appear
in the display.
Travelstore
To store and recall the six most powerful stations with Travelstore.
To store: Press button for approximately 1 sec. until you hear a beep
and “T-STORE” appears in the display.
To recall: Select the memory bank “T”
and press the corresponding preset
button (1-6) briefly.
Casablanca RCM 127,
Cannes RCM 127, Woodstock DJ A:
Additional selection of medium- and
long-wave stations, provided that “AM
ON” has been adjusted in the DSC
menu.
8 AF
Alternative frequency during RDS operation:
When “AF” lights up in the display, the
system will automatically seek a frequency offering better reception of the
same RDS programme.
AF on/off: Press AF briefly.
Regional function on/off:
Press the AF button for approximately
1 sec. until you hear a beep. “REGON” or “REG-OFF” will appear in the
display (see chapter REG - regional
programme).
9 TA (priority for traffic announcements)
When “TA” lights up in the display, the
system will play traffic stations only.
Priority on/off: Press TA.
: 1, 2, 3, 4, 5, 6 - preset buttons
You can store six stations for each of
the memory banks I, II and T.
To store a station: Press a preset
button during radio operation and hold
down until the set resumes play after
the muting and you hear a beep.
To recall a station: Select the desired
memory bank and press the relevant
preset button briefly.
30
Coburg ..RCM127 gb
30
13.02.2001, 10:19 Uhr
Extra function /
Frequency display during radio operation:
Press button briefly.
The frequency will be briefly displayed.
> Cassette loading slot
Insert the tape with side A or 1 facing
up, the open side showing to the right.
DEUTSCH
Preset Scan
Press SC for approximately 1 sec. until
you hear a beep.
“SCAN” and the name or frequency of
the scanned station will alternately appear in the display.
The unit will scan all stations stored on
the preset buttons.
ENGLISH
FRANÇAIS
Scan
Press SC briefly.
The scanned frequency or the station
name will start flashing in the display.
During the actual scanning process
“FM-SCAN” or “AM-SCAN” will be displayed. The unit will scan all FM stations which can be received.
ITALIANO
/
To switch the tape side: Press briefly.
To eject the tape: Press for approximately 1 sec.
Radio operation
To stop Scan / Preset Scan:
Press SC once again.
PORTUGUÊS
ESPAÑOL
< lo
To switch the seek tuning sensitivity
level:
Press button briefly.
If “lo” is displayed, the radio will only
pick up strong, local stations (normal
sensitivity).
If “lo” does not light up, the radio will
also pick up weaker, distant stations
(high sensitivity).
=
? SC
NEDERLANDS
; SRC (Source)
You can switch between the radio,
tape and CD changer operating
modes, provided that a cassette/CD is
inserted.
Extra function of lo button:
To switch between mono and stereo
reception:
Press button for approximately 1 sec.
(beep).
The selected condition will be briefly
displayed.
SVENSKA
Extra function of preset buttons
To store and recall a PTY programme
type.
When PTY is active (“PTY” lights up in
the display), you can store and recall
one programme type on/from each
preset button on FM.
31
Coburg ..RCM127 gb
31
13.02.2001, 10:19 Uhr
Tape operation
Cassetten-Scan
Press SC.
“CC-SCAN” will appear in the display.
All cassette titles will be scanned briefly.
To stop cassette scan:
Press SC once again.
Changer operation
CD-Scan
Press SC briefly.
“CDC-SCAN” will appear in the display.
All CD titles will be scanned briefly.
To stop CD-Scan:
Press SC once again.
@ PTY (Programme Type)
In the PTY mode, the preset buttons
become programme type buttons. With
every preset you can select one programme type, such as for example
NEWS, SPORT, POP MUSIC, EDUCATE, etc.
A DSC (Direct Software Control)
Use the DSC function to customise
certain programmable, basic settings
to suit your personal needs and preferences. See chapter “DSC programming” for more information.
B AUD
To adjust the treble, bass, balance and
fader.
If the display shows “TRE” or “BAS”,
you can adjust the reproduction of the
treble and bass frequencies with the
rocker switch. If “BAL” or “FAD” is displayed, you can set the balance (left/
right) and fader (front/rear).
Press AUD as many times as required
and make the setting using the rocker
switch.
The last setting will be stored automatically.
To switch off AUD: Press button once
again.
If the setting remains unchanged within 8 seconds, the display will switch
back to the previous condition.
Extra function AUD
Loudness - When listening at a low
level, the Loudness function creates a
more natural sound by boosting
the low frequency range.
Loudness on/off: Press AUD for approximately 1 sec.
“LD” lights up in the display if the
Loudness function is switched on.
Please refer to chapter “DSC programming” for more information on how to
program the Loudness boost.
Treble + / Fader front
Treble – / Fader rear
Bass – / Balance left
Bass + / Balance right
32
Coburg ..RCM127 gb
32
13.02.2001, 10:19 Uhr
Accessories
Before starting to use your new car radio,
please read the following information carefully.
If you would like to install your new car stereo yourself or add other audio components
to existing ones, then please read carefully
the enclosed instructions on installation and
connection.
In order to ensure that the set operates properly it is necessary that the positive power
supply line is connected to the ignition and
the permanent +12 V lead.
Do not ground the loudspeaker outputs!
Use accessories and spare parts approved
by Blaupunkt only.
Telephone mute
CDC A 05/F 05
(adapter cable 7 607 889 093 is required),
CDC A 06
All Blaupunkt amplifiers, the preamp-out
cable 7 607 893 093 is required.
NEDERLANDS
Changer
(Woodstock DJ I, Woodstock DJ A):
CDC A 06 included in the delivery.
Remote control
With the infrared remote control RC 06 you
can control all of the important functions of
your car radio system from the steering
wheel.
SVENSKA
If there is a mobile telephone installed in your
vehicle, the radio, tape player or CD player
can be muted automatically when the phone
is being used.
“PHONE” will then appear in the display.
When TA is active, traffic messages will always have priority. The announcement will
be aborted by pressing the TA button.
Amplifier
PORTUGUÊS
Traffic safety always has the highest priority.
As the driver of a motor vehicle, it is your
responsibility to pay attention to the traffic
situation at all times. Never use your car
radio in a way that could distract you.
Please keep in mind that you travel a distance of 14 m per second at a speed of only
50 km/h.
Should the traffic situation become particularly demanding, we advise you not to use
the radio.
Always make sure that you are still able to
hear any warning signals coming from outside of the vehicle, such as police or fire
engine sirens, so that you can react accordingly.
Therefore, you should always select a moderate volume for playing your car radio while
you are driving.
ESPAÑOL
Traffic safety
You can use the following Blaupunkt products with this car radio:
FRANÇAIS
Installation
ITALIANO
Precautions
ENGLISH
DEUTSCH
Important notes
33
Coburg ..RCM127 gb
33
13.02.2001, 10:19 Uhr
KeyCard theft protection system
This car radio is supplied with one KeyCard
as standard, though it can also be operated
with a second card.
If you have lost your KeyCard or if it was
damaged, you can buy a new one from your
specialised dealer.
When using a second KeyCard, the settings
stored on the first card will be adopted. However, you can individually store the following functions:
Bass, treble, balance and fader settings,
Loudness, TA (traffic announcement volume), beep volume.
In addition, the settings activated before
switching the radio off, such as the station
tuned in, TA priority, AF, AM ON/OFF and
RM ON/OFF will also remained stored.
This ensures that you will find your basic
settings re-adjusted automatically as soon
as you have inserted your KeyCard.
The system will switch off after approximately 10 seconds.
When inserting another card type (e.g.
phone or credit card), the display will show
“WRONG KC” for approximately 2 seconds.
The set will switch off automatically.
Remove the wrong card and introduce the
correct KeyCard.
• Press ON to turn on the set.
Putting the unit into operation
While operating the unit with the first
KeyCard, you can “train” a second one to
be also used with the set:
• Insert the first KeyCard and turn on the
set.
•
Turn on the set.
With the KeyCard tongue sticking out,
introduce the KeyCard into the slot
with the contact area showing up.
The car radio is now ready for operation.
If a wrong KeyCard is inserted, then “CARD
ERR” followed by “WAIT” will appear in the
display. In this case please do not make any
further adjustments.
Removing the KeyCard
Never pull out the KeyCard directly!
• First, slightly push in the KeyCard.
This releases the card and puts it in the proper position for being removed.
• Now you can pull it out.
“Training” a second KeyCard/
Replacing a KeyCard
•
•
Push in the KeyCard. The card is released and put in the proper position
for being removed.
•
Remove the first KeyCard and insert
the new one.
After the display indication “READY” or
“LEARN KC”,
• press DSC.
Now you can also use the new KeyCard for
operating your unit.
A maximum of two cards can be used for
the set.
When trying to “train” a third one, the access authorisation for the KeyCard not used
for the “training” process will be deleted automatically.
Displaying the radio pass data
Using the KeyCard supplied with your set
you can have the radio pass data such as
the model name, product number (7 6..) and
serial number indicated on the display panel.
Please refer to chapter “DSC programming
- READ KC”.
Press the DSC button and select
“LEARN KC” with / .
• Press << or >>.
The display will switch to “CHANGE”.
34
Coburg ..RCM127 gb
34
13.02.2001, 10:19 Uhr
Using the second KeyCard to be purchased
at any specialised dealership, you can program a short text by selecting the DSC menu
item READ KC. This text will be moved
through the display and might be the telephone number of a car repair service or the
emergency call number of your auto club.
Any specialised dealer with the proper
equipment can program the desired text with
up to a maximum of 162 characters onto the
KeyCard.
Flashing KeyCard tongue
radio,
When the vehicle is stationary and the
KeyCard removed, the KeyCard tongue can
be switched to flash for extra anti-theft security.
For this it is necessary that the positive power supply line and the permanent +12 V lead
are connected such as described in the installation instructions.
Be sure that “LED ON” is adjusted in the
DSC mode.
If required, please refer to chapter “DSC
programming - LED”.
tape,
NEDERLANDS
ITALIANO
To switch to another source,
• press SRC briefly.
Switching off the flashlight
SVENSKA
The flashlight can be switched off by pushing in the KeyCard and lock.
If you would like to deactivate the flashing
tongue with general effect, adjust the relevant item in the DSC menu to “LED OFF”.
Care of your KeyCard
ESPAÑOL
Using the second KeyCard to be purchased
at any specialised dealership, you can program the unit to display a selected “Turn On
Message” after the set is switched on.
Any specialised dealer with the proper
equipment can program the desired text with
up to a maximum of 48 characters onto the
KeyCard.
Each time you switch on your car radio using the second KeyCard, this text will appear in the display.
changer (optional for Coburg RCM
127, Casablanca RCM 127 and
Cannes RCM 127).
Tape/changer operation is only available if
a cassette/disc is inserted.
In order to ensure that the KeyCard always
functions correctly, it is important for the
contacts to be free from any foreign particles. Avoid direct skin contact.
If necessary, clean the KeyCard contacts
using a cotton swab dipped in alcohol.
PORTUGUÊS
Turn On Message (T.O.M.)
Using the SRC button you can switch between the following audio sources:
35
Coburg ..RCM127 gb
35
13.02.2001, 10:19 Uhr
DEUTSCH
Optical indication of anti-theft
protection
ENGLISH
Short Additional Memory
(S.A.M.)
FRANÇAIS
Switching the audio source
Radio operation with RDS (Radio Data System)
The Radio Data System offers you more
convenience when listening to FM radio stations.
More and more radio stations have begun
to broadcast RDS information alongside
their programmes.
As soon as a programme has been identified, the station name including a regional
identifier, if applicable, will appear in the display, for example, NDR1 NDS (regional programme in Lower Saxony, Germany).
When RDS is activated, the preset buttons
become programme buttons. You now know
exactly which programme you have tuned
into, making it easy to find the desired station quickly.
But RDS offers you further advantages:
AF - Alternative frequency
The AF (Alternative Frequency) function
makes sure that the strongest frequency of
the currently selected programme is always
tuned in automatically.
This function is activated when “AF” appears
in the display.
In order to switch this function on or off,
• press the AF button briefly.
While searching for the strongest reception
signal, the radio may switch to mute briefly.
If “SEARCH” appears in the display when
switching on the radio or recalling one of the
stored frequencies, the unit is automatically
searching for an alternative frequency.
“SEARCH” will disappear from the display
when the alternative frequency has been
found or after the frequency band has been
run through completely.
If the reception quality of the selected programme becomes too bad:
• Tune into another station.
If you leave the service area of the regional
programme tuned into, or if you would like
to take advantage of the full RDS service,
switch to “REG OFF”.
• Press the AF button for approximately
1 sec. until “REG OFF” appears.
If the REG function is active, “REG ON” will
be briefly displayed each time the radio is
switched on.
Selecting a waveband
(only Casablanca RCM 127,
Cannes RCM 127, Woodstock DJ A)
REG - regional programme
Certain radio programmes are split up at
times into regional programmes offering local information. The 1st programme broadcast by NDR, for example, offers programmes with different contents in the northern states of Germany Schleswig-Holstein,
Hamburg and Lower Saxony at certain times
of the day.
If you are listening to one regional programme and move to an area where another linked regional programme becomes
stronger, the unit will switch to that programme.
If you wish to continue listening to the first
programme,
• press the AF button for approximately
1 sec.
“REG ON” appears in the display.
You can select between the following wavebands:
FM 87.5 - 108 MHz
MW 531 - 1602 kHz
LW 153 - 279 kHz
• Press the BND button until the desired
waveband shows on the display panel.
Note:
In the DSC menu you can deactivate the
station selection on either MW or LW or for
both wavebands at the same time.
This has the advantage that only the required bands will allow to be activated, so
that you must press the BND button less
often. For more information, please refer to
chapter “DSC programming - AM ON/OFF”.
36
Coburg ..RCM127 gb
36
13.02.2001, 10:19 Uhr
Seek tuning
Up
Down
Down in short intervals
(“AF” must be switched off)
Up in short intervals
(“AF” must be switched off)
Manual tuning with << >>
You can also tune in a station manually.
Condition:
AF and PTY must be switched off (i.e. the
symbols do not light up in the display).
If necessary, deactivate these functions:
• Press AF or PTY briefly.
You can use the << >> buttons to tune in
stations of your reception area.
If several programmes of the broadcasting
networks can be received, you can scroll
through them in forwards direction pressing
>>, or backwards using the << button, e.g.
NDR 1, 2, 3, 4, N-JOY, FFN, ANTENNE ...
For this it is necessary that the stations have
been tuned in at least once and that “AF” is
active (lights up in the display).
For this purpose, you may start Travelstore
seek operation:
• Press FMT or BND for 1 sec.; the
system starts to run through the frequency band. The display shows
“T-STORE”.
If “AF” does not light up,
• press AF.
This fulfils the requirements for selecting
stations with << >>.
On FM, you can store six stations on the
preset buttons 1-6 for each of the memory
banks I, II and T.
On MW/LW, you can also store six stations
each. (only with Casablanca RCM 127,
Cannes RCM 127, Woodstock DJ A)
• Select the desired memory bank.
•
Tune in a station with the rocker switch
(either automatically or manually).
•
Press and hold down the desired preset button until the radio resumes play
after the muting (takes approximately 1
sec., confirmed by beep).
Now the station has been stored.
The activated preset button is indicated in
the display.
37
Coburg ..RCM127 gb
37
13.02.2001, 10:19 Uhr
ENGLISH
DEUTSCH
Storing stations
FRANÇAIS
Scrolling through the broadcasting networks
ITALIANO
Press / ; the car radio will automatically search for the next station.
When keeping the upper or lower part /
of the rocker switch depressed, seek tuning
will speed up in upwards or downwards direction.
NEDERLANDS
•
You can shift between the memory banks I,
II and T in order to store stations and recall
them later.
The currently selected memory bank is indicated in the display.
• Press the FMT or BND button as many
times until the desired memory bank
lights up in the display.
SVENSKA
/
Changing the memory bank
ESPAÑOL
Automatic tuning
Manual tuning:
• Press << >>; the frequency will change
in short intervals in downwards or upwards direction.
When holding the right or left part of the rocker switch depressed, the frequency scan is
speeded up.
PORTUGUÊS
Station tuning
Notice:
Should you tune in a station which has already been stored before, then the corresponding preset position and memory bank
will briefly flash in the display.
Recalling stored stations
Automatically storing the
strongest stations with
Travelstore
•
You can automatically store the six most
powerful FM stations of your current reception area sorted according to their signal
strength. This function is particularly convenient on longer trips.
• Press the FMT or BND button for
1 sec.
“T-STORE” will appear in the display.
The six strongest FM stations will be automatically stored on the memory bank “T”
(Travelstore). When this process has been
completed, the radio will play the first station stored on preset 1.
If desired, stations can also be stored manually on the Travelstore bank (see “Storing
stations”).
Scanning stations with RadioScan
You can recall any stored station at the touch
of a button.
• Select the memory bank with FMT or
BND.
Press the corresponding preset button
briefly to recall the station.
Scanning stored stations with
Preset Scan
You can have all of the stored stations briefly
scanned on all wavebands.
To start Preset Scan:
• Press SC for approximately 1 sec.
All of the stored stations to be received will
be scanned one after the other.
To select a scanned station and switch
off Preset Scan:
• Press SC briefly.
You can also scan all stations which can
currently be received.
To start the Scan function:
• Press SC briefly.
The scanned frequency or the station name
will start flashing in the display. During the
actual scanning process “FM-SCAN” or
“AM-SCAN” will be displayed.
To select a scanned station and switch
off Radio-Scan:
• Press SC briefly.
If no station is selected, the scan function
will be automatically switched off after the
frequency band has been run through completely. The unit will tune in the station listened to before starting the scan.
Note:
If “TA” shows on the display panel, the system will scan the stored traffic stations only.
38
Coburg ..RCM127 gb
38
13.02.2001, 10:19 Uhr
Every time the radio is switched on, stereo
playback is activated automatically.
The unit will gradually switch to mono if reception is poor.
You can also switch between mono and stereo reception manually:
• Press the lo button for approximately
1 sec.
The selected condition will briefly appear in
the display.
PTY – Programme-Type
PTY is an RDS service offered by more and
more radio broadcasters. This feature allows
you to select FM stations according to their
programme type. After you have chosen the
PTY of your preference, the corresponding
stations can be selected either by seek tuning or using the scan function.
Switching PTY on/off
• Press PTY.
When the function is active, the programme
type selected last will briefly appear in the
display. “PTY” will be permanently indicated in the lower right corner of the display
panel.
39
13.02.2001, 10:19 Uhr
ENGLISH
DEUTSCH
NEWS
CURRENT AFFAIRS
INFORMATION
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP MUSIC
ROCK MUSIC
M.O.R. M (middle of the road music)
LIGHT M (light classical)
CLASSICS (serious classical)
39
Coburg ..RCM127 gb
FRANÇAIS
Switching Loudness on/off:
• Press the AUD button for approximately 1 sec.
When the Loudness function is active, “LD”
will light up in the display.
See chapter “DSC programming” for more
information.
ITALIANO
Use << >> to have the last selected programme type displayed and to choose a new
one.
You can select any one of the stored types
with the preset buttons 1-6.
Condition: PTY must be active.
Using DSC you can choose between German and English (see “DSC programming PTY LANG”).
All of the programme types listed below are
available.
The letters printed in bold are identical to
the actual short-time indication in the display.
NEDERLANDS
Switching from stereo to mono
Adjusts the low bass frequencies for a more
natural sound.
SVENSKA
To switch the seek tuning sensitivity:
• Press lo briefly.
The sensitivity level can be altered separately in both modes. Please refer to chapter “DSC programming - S-LO, S-DX”).
Programme type
ESPAÑOL
You can alter the automatic seek tuning
sensitivity.
If “lo” is displayed, the radio will only pick up
strong, local stations.
If “lo” does not light up, the radio will also
pick up weaker, distant stations.
Loudness
PORTUGUÊS
Selecting the seek tuning sensitivity
OTHER M (other music)
WEATHER
FINANCE
CHILDREN’S PROGRAMMES
SOCIAL AFFAIRS
RELIGION
PHONE IN
TRAVEL
HOBBIES
JAZZ MUSIC
COUNTRY MUSIC
NATIONAL MUSIC
OLDIES MUSIC
FOLK MUSIC
DOCUMENTARY
ALARM TEST
Checking the programme type of the
station
• Press PTY for approximately 1 sec.
After the beep tone the display will show the
programme type offered by the tuned in station.
If “NONE” appears in the display, the current station has no PTY code.
b) Using the << >> buttons of the rocker
switch
Displaying the selected programme
type
• Press << or >>.
The programme type selected last will be
displayed briefly.
When PTY is switched on, you can select a programme type using buttons
<< >>.
•
Press << or >>; the programme
type selected last will be displayed
for 3 seconds.
When PTY is switched on, you can use
the preset buttons 1-6 to select the
programme types stored at the factory.
•
During this period press >> (forwards) or << (backwards) to select
the desired type.
• Press one of the presets 1-6.
The selected programme type will be
displayed for 2 seconds.
•
Press << or >> as many times as
required.
Selecting a programme type
a) Using the preset buttons
If you wish to listen to a station with
this PTY,
• press / to start seek tuning.
If the system is unable to find a station offering the selected programme type, the display will show “NO PTY” and a beep tone
will be released. The station received before starting seek tuning will be tuned in.
You can assign different programme types
to each preset position. Please refer to chapter “Storing programme types”.
If you wish to listen to a station offering
the selected PTY,
• press / to start seek tuning.
If the system is unable to find a station offering the selected programme type, the display will show “NO PTY” and a beep tone
will be released. The station received before starting seek tuning will be tuned in.
40
Coburg ..RCM127 gb
40
13.02.2001, 10:19 Uhr
hold down the desired preset button
(1-6) until you hear a beep.
Now the selected programme type can be
recalled by pressing this preset. For this, the
PTY function must be active.
Example: German broadcasting network
NDR:
Scanning stations with PTY-SCAN
-
Station tuned in: NDR3.
Condition: “PTY” must appear in the display.
-
“PTY” lights up in the display.
• Press the SC button.
All of the received stations offering the selected programme type will be scanned.
-
Programme type “POP” selected.
-
Seek tuning is started.
-
No station with “PTY-POP” can be
found.
To switch off PTY-SCAN:
• Press SC once again.
-
The display shows “NO PTY” and
-
automatically switches back to NDR3.
-
NDR2 airs a “PTY-POP” programme.
-
The system will switch to the linked
NDR2 station for the duration of the
“POP” programme.
41
Coburg ..RCM127 gb
41
DEUTSCH
SVENSKA
•
ESPAÑOL
Select a programme type using buttons << >> and
Notice:
As mentioned earlier, these functions are
currently only supported by a limited number
of RDS stations.
PORTUGUÊS
•
PTY is switched on and lights up in the display.
No station offering the selected programme
type can be currently received (neither with
seek tuning nor with scan).
The set will switch back to the previous station.
As soon as a programme with such PTY can
be received within the broadcasting network,
the unit will switch over to the corresponding station for the duration of the programme.
During tape operation, the set will also automatically switch to the programme offering the selected PTY within the broadcasting network.
After the PTY programme the system will
remain in the radio mode.
ENGLISH
Situation:
FRANÇAIS
At the factory, one programme type was
assigned to each of the preset buttons 1-6.
If desired, you can also store other available programme types.
To do so, make sure that “PTY” lights up in
the display.
• If necessary, press the PTY button to
switch on the function.
ITALIANO
PTY priority
NEDERLANDS
Storing programme types
13.02.2001, 10:19 Uhr
Receiving traffic programme stations with RDS-EON
The abbreviation “EON” stands for Enhanced Other Networks, meaning the exchange of information within a radio network.
Many FM broadcasters offer traffic messages for their service area at regular intervals.
All traffic programme stations transmit a
special carrier signal alongside their programmes, which is decoded by your car radio. If this signal is identified, “TP” will appear in the display (Traffic Programme).
In addition to these, there are also stations
which do not actually transmit traffic programmes themselves, but by using RDSEON they offer the possibility to receive the
traffic messages broadcast by another traffic programme station in the same radio
network.
If you wish to have the priority for traffic announcements activated while listening to
one of these stations (e.g. NDR3), “TA” must
appear on the display panel.
If a traffic announcement is broadcast, the
radio will automatically switch to the linked
traffic programme station (in this case,
NDR2) for the duration of the message and
return to the original programme (NDR3)
afterwards.
Traffic announcement priority
on/off
If the priority for traffic announcement programmes is activated, “TA” will light up in
the display.
To switch the priority on or off:
• Press the TA button.
When pressing TA while a message is being broadcast, this message will be interrupted. The unit will then switch back to the
previous condition. The priority for all other
traffic messages remains active.
Please note that several buttons have no
function while a traffic announcement is
broadcast.
Switching off the beep tone
a) Tune into another station offering traffic information:
•
Press the rocker switch or
•
press a preset button which has a
traffic programme station allocated
to it.
Alternatively:
b) Switch off the priority for traffic announcements:
• Press TA.
“TA” will disappear from the display.
Automatic seek tuning start
(tape and CD changer operation)
Beep tone
If you leave the reception area of the traffic
programme station currently tuned into, you
will hear a beep tone approximately every
30 seconds.
This tone will also be released when pressing a preset button which has no traffic programme allocated to it.
When leaving the reception area of the tuned
in traffic programme station while listening
to a tape or CD, the system will automatically start searching for a new TA programme.
If no such station is found within approximately 30 seconds, you will hear a warning
beep every 30 seconds. To switch off the
beep tone proceed as described above.
42
Coburg ..RCM127 gb
42
13.02.2001, 10:19 Uhr
ENGLISH
The unit will automatically switch to tape
operation when inserting a cassette.
Inserting a tape
FRANÇAIS
Turn on the set.
• Insert a tape.
The cassette will be automatically transported to the playback position. Side A or 1 starts
to play.
During tape operation, “TR 1” or “TR 2”
(track) will be indicated on the display panel.
Stop function by pressing
Insert the tape with side A or 1 facing up, the open side
showing to the right.
Selecting titles with CPS
Fast forward
Fast rewind
Title selection (S-CPS)
Up
Down
ITALIANO
/
.
(Cassette Programme Search)
Use this function to skip ( ) and repeat ( )
recorded titles.
Removing a tape
Press
for 1 sec.
The cassette will eject.
PORTUGUÊS
•
To start CPS:
• Press / .
In order for CPS to function properly, there
has to be an unrecorded tape portion of at
least 3 seconds between the individual titles.
NEDERLANDS
•
SVENSKA
This volume was preset at the factory,
though you can alter the value using the
DSC function (see “DSC programming, TA
VOL”).
If the volume level is altered while a message is being played, this will only affect the
current announcement.
Fast Forward/Rewind
The car stereo has to be switched on.
ESPAÑOL
Adjusting the volume for traffic
announcements and the beep
tone
DEUTSCH
Tape operation
43
Coburg ..RCM127 gb
43
13.02.2001, 10:19 Uhr
Switching the tape side
(autoreverse)
Scanning cassette titles with
SCAN
To change the tape direction during cassette
playback:
briefly.
• Press
At the end of a tape side the mechanism
changes directions automatically to play the
other side (autoreverse). The display shows
“TR 1” for track (side) 1 or “TR 2” for track 2.
You can have the cassette titles played briefly by using the scan function. If you like a
title, stop the scan to continue listening to
that track.
Notice:
If there is too much tension on the tape during playback, the set may switch over by itself before having reached the end of the
tape side. In this case check the condition
of the cassette tape. Sometimes it helps to
rewind it completely.
Tape equalisation
When a metal or CrO2 tape is inserted, the
tape mechanism automatically adjusts to
metal/CrO2 tape equalisation.
Care notes
To start/stop the scan function:
• Press the SC button briefly.
Scan condition: There has to be an unrecorded tape portion of at least 3 seconds
between the individual titles.
Listening to the radio during
fast tape winding with RM
(Radio Monitor)
To avoid possible problems, we recommend
you to use C-60/C-90 type cassette tapes
only. Store your tapes in a cool place away
from dirt, dust and temperatures exceeding
50 °Celsius. Allow very cold tapes to warm
up before playing them in order to avoid
uneven tape transport. After approximately
100 hours of use, dust particles collected
on the playback head or roller may lead to
tape run problems and sound distortions.
Use a head cleaning tape to remove normal dirt build-up. For tougher cases, use a
cotton swab (Q-Tip) dipped in alcohol. Do
not attempt to clean by inserting a hard object into the player!
When the tape is fast forwarded or rewound
(also with CPS), the radio will normally be
muted. In order to listen to the radio during
fast winding, you can activate the Radio
Monitor function.
For more information please refer to chapter “DSC programming - RM ON/OFF”.
44
Coburg ..RCM127 gb
44
13.02.2001, 10:19 Uhr
CD selection
Up
Down
Note:
Use only perfectly circular CDs.
CDs manufactured in the shape of a butterfly or a beer mug, for example, are not suitable for use with this equipment.
Using such CDs can very likely result in the
destruction of the CD and the CD drive.
We assume no responsibility for damages
caused by using unsuitable CDs.
Switching to the CD changer
mode
Upwards: Press briefly.
CUE - fast advance (audible): Keep
depressed.
Downwards: Press as many times as
required.
To re-start a title: Press briefly.
REVIEW - fast reverse (audible):
Keep depressed.
MIX OFF – The Mix function is deactivated. Discs and titles will be
selected in numeric order.
To change the MIX mode:
• Press DSC.
Select “MIX” using the rocker switch /
and adjust with
/ .
If the function is active, “CDC MIX” will be
displayed every time CD changer operation
is activated.
PORTUGUÊS
Make sure that at least one CD has been
inserted into the magazine.
Press SRC to toggle the audio source:
• Press repeatedly until the CD functions
appear in the display.
Title selection
MIX CDC – The MIX mode is active:
The individual discs and the
titles of the selected CD are
chosen randomly. After all
titles have been played, the
next CD will be selected at
random again.
Use to select a CD title in
random order.
ENGLISH
This piece of equipment offers you convenient control of a Blaupunkt CD changer CDCA 05/F 05 (with adapter 7 607 889 093) /
CDC-A 06.
Select the desired MIX mode in the DSC
menu.
FRANÇAIS
Included in scope of delivery:
Woodstock DJ I, Woodstock DJ A
ITALIANO
You can have the CD tracks played in random order.
NEDERLANDS
MIX playback
SVENSKA
Selecting CDs and titles
ESPAÑOL
Optional:
Coburg RCM 127, Casablanca RCM 127,
Cannes RCM 127
DEUTSCH
CD changer operation
45
Coburg ..RCM127 gb
45
13.02.2001, 10:19 Uhr
Selecting the display mode
SCAN
You can select the desired display mode for
CD playback:
Use this function to scan all of the CD tracks.
“CDC NUMBER” – The CD number, such
as “CD 8” is displayed.
“TIME”
– The elapsed playback
time of the current title
is displayed, for example “2 : 32”.
To switch the display mode:
• Press DSC.
Use the rocker switch / to select
“CDC DISP”.
To start the Scan function:
• Press SC.
The titles will be scanned one after the other in ascending order.
To stop the Scan function:
• Press SC briefly.
The track currently being scanned is continued to be played.
SCAN will also be terminated by
• pressing one of the buttons AUD,
GEO, DSC, SRC, << >> or / .
•
Use
/
to adjust to “NUMBER” or
“TIME”.
You can also change the display mode immediately for the title currently playing by
.
pressing
46
Coburg ..RCM127 gb
46
13.02.2001, 10:19 Uhr
AM ON / OFF (Casablanca RCM 127,
Cannes RCM 127, Woodstock DJ A)
You can deactivate one or
both AM bands (MW/LW) in
order to reduce the number
of bands for selection with
BND.
LOUDNESS When listening at a low level, the Loudness function
creates a more natural
sound by boosting the low
frequency range.
LOUD 1 - Low boost
LOUD 6 - Max. boost
TA VOL
selectable:
/
<< >>
AM ON
MW OFF
LW OFF
AM OFF
Select function
Adjust/recall value
–
–
–
–
all bands
LW, FM
MW, FM
FM
To adjust the traffic announcement and beep tone
volume from between 0 to
63.
The message will then come
through at this volume, if the
standard volume is lower.
If the standard volume is
higher than the TA VOL level, the traffic report will be
played slightly louder than
the standard volume.
47
Coburg ..RCM127 gb
47
13.02.2001, 10:19 Uhr
DEUTSCH
ENGLISH
FRANÇAIS
MIX OFF The MIX function is
switched off.
ITALIANO
MIX CDC CD selection at random.
All titles of this disc will be
chosen in random order as
well.
The next disc is again selected at random.
RM ON / OFF (Radio Monitor)
Allows you to listen to the
radio during fast winding of
the tape.
RM ON – Radio playback
activated
RM OFF – Function deactivated
NEDERLANDS
For changer operation only.
SVENSKA
• press DSC.
Use the rocker switch to select and adjust
the functions described in the following. The
display will show you the adjusted condition.
MIX
ESPAÑOL
DSC (Direct Software Control) allows you
to customise certain programmable, basic
settings to suit your personal needs and
preferences and then store them.
The basic settings for this audio equipment
were made at the factory.
In the following you can find an overview of
these settings, so that you can always reset
to these if desired.
If you wish to alter any of the programming,
• press SRC to choose the desired operating mode (e.g. radio, if you wish to
change the language with PTY LANG).
PORTUGUÊS
DSC programming
BEEP
Acknowledgement tone for
all functions which require a
button to be pressed for
more than 1 second.
The volume can be adjusted
from between 0 to 9. (0 =
off)
READ KC
LED ON/OFF You can choose between
LED ON or LED OFF. With
LED ON, the KeyCard
tongue will flash for extra
anti-theft protection when
the unit has been switched
off and the KeyCard removed.
LEARN KC
To “train” a second
KeyCard.
Please read the information
in chapter “KeyCard theft
protection system - Training
a second KeyCard”.
To read out the KeyCard
data.
The KeyCard supplied with
the radio is used to display
the model name, type
number (7 6..) and the serial
number.
Using the second KeyCard
to be purchased at any specialised dealership it is possible to display the Short
Additional Memory (S.A.M.)
data entered by the dealer.
See chapter “Short Additional Memory S.A.M.”.
If you remove the KeyCard
during the reading process,
“READ KC” will show on the
display panel.
PTY LANG
To select the programme
type language: DEUTSCH
or ENGLISH
S-DX
To adjust the seek tuning
sensitivity for distant reception.
DX 1 - high sensitivity
DX 3 - low sensitivity
S-LO
AUX ON/OFF Please note that this item
will not appear if you have
connected a CD changer.
Default setting: AUX OFF.
Adjust to AUX ON if you
have connected an external
piece of equipment to the
AUX socket.
VOL FIX
48
Coburg ..RCM127 gb
48
To adjust the seek tuning
sensitivity for local reception.
LO 1 - high sensitivity
LO 3 - low sensitivity
The seek tuning sensitivity
values can be set separately
for AM and FM.
13.02.2001, 10:19 Uhr
Use this function to select
the volume at which the radio is set when it is switched
on. Adjust the desired volume level with << >>. When
adjusted to “VOL 0”, the
system will come on with the
volume selected before
switching it off.
(Casablanca RCM 127, Cannes RCM 127,
Woodstock DJ A)
MW
531 – 1602 kHz
LW
153 – 279 kHz
FM sensitivity:
0.9 µV at 26 dB signalto-noise ratio
FM frequency response:
30 - 16 000 Hz
(Casablanca RCM 127, Cannes RCM 127,
Woodstock DJ A):
AM
ON
Tape player
Frequency response:
30 - 18 000 Hz
ENGLISH
If you would like to know the address of
the next Blaupunkt service centre of
your area without having our service list
at hand:
- Find out your area code.
-
Then call the following chargeable
phone number: 01 80 / 5 25 56 66.
-
Using the area code to be entered
you will be automatically given the
address and phone number of the
next Blaupunkt service centre. You
can also request this information
by fax.
PORTUGUÊS
CD changer
Frequency response:
5 - 20 000 Hz
Subject to modifications!
49
Coburg ..RCM127 gb
49
FRANÇAIS
87.5 – 108 MHz
Address of the next service
centre in your vicinity
(only for Germany)
ITALIANO
OFF
OFF
3
35
4
ON
ENGLISH
1
1
0
Tuner
Wavebands:
FM
:
4 x 23 W RMS power
acc. to DIN 45324 at
14.4 V
4 x 35 W max. power
Blaupunkt
telephone hotline
ESPAÑOL
MIX
RM
LOUDNESS
TA VOL
BEEP
LED
LEARN KC
READ KC
PTY LANG
S - DX
S - LO
VOL FIX
Amplifier
Output power:
NEDERLANDS
Overview of DSC factory settings
Specifications
SVENSKA
To quit the DSC programming mode
and store the adjustment:
• Press DSC.
The DSC programming mode will be automatically quit 8 seconds after having made
the last adjustment.
DEUTSCH
Appendix
13.02.2001, 10:19 Uhr
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising