Jordan MK75 specs

Jordan MK75 specs
CRN Registration Number Available
Wafer Style Control Valves
The Mark 75 wafer style control valve was developed by Jordan Valve as the next generation
of control valves. Featuring all the benefits of the
time-tested Sliding Gate design, in a lightweight,
compact wafer-style body, the Mark 75 dramatically reduces the size and weight of conventional
control valves.
The Mark 75 offers a variety of design features
that help provide the superior performance customers expect from Jordan Valve.
Control Valves
Mark 75 Series
Pricing Advantage
Weight Advantage
The weight advantage also allows you to spend
less money and time on installation and support.
With a 6" Mark 75 weighing less than 80 lbs (36,3
kgs), there is no need to rent a lift to put the valve
in line as you would have with heavier alternative valves. Supporting the lighter weight Mark 75
is much simpler and less costly than a standard
globe style valve.
With Jordan Valve's time-tested sliding gate seats
at the heart of the Mark 75, the stroke remains
much smaller than typical globe style valves. The
shorter stroke means smaller actuators are needed to operate the valve, increasing the accuracy of
the Mark 75 while reducing the overall weight and
air consumption.
Capacity
The Mark 75 provides great capacity in a compact wafer style body. A 2" Mark 75 provides 72
Cv (62 Kv), a 6" Mark 75 provides 400 Cv (345
Kv) and an 8" Mark 75 provides 600 Cv (522 Kv)
as the linear operating Cv. (Refer to Cv Capacity
Charts for information concerning all line sizes).
Ease of Maintenance
The Mark 75 features a 'T' slot design connection
to the disc. This connection allows for quick and
easy reversing of functions. Instead of having to
go into the actuator to change action, all that is
needed in a Mark 75 is to turn the seats 180°.
With this simple rotation, the valve can go from
reverse acting to direct acting (or vice versa).
The stroke length of the Mark 75 is a slightly
longer stroke than standard sliding gate valves.
This longer stroke enables better turndown.
Combined with the capacity of the Mark 75, the
increased turndown makes for a great control
valve.
Jordan Valve a division of Richards Industries
3170 Wasson Road • Cincinnati, OH 45209
513.533.5600 • 800.543.7311 • 513.871.0105 (f)
[email protected] • www.jordanvalve.com
Mark 75 Pneumatic Control Valves
What does this mean to you? You pay for less metal
to make the valve. In the case above, 15.50" (394
mm) of metal! The actual material is only part of the
savings. You pay less for machining time; even shipping costs are reduced due to the lighter weight.
The Mark 75 offers an incredible pricing advantage
in the market place due to its wafer style body. A
6" Mark 75 valve is only 2.23" (56,6 mm) face-toface in comparison to a 6" Mark 707/711 that is
17.75" (451 mm) face-to-face.
Mark 75 Series Wafer Style Control Valves
Specifications
Action
• Direct (ATC)
• Reverse (ATO)
Body Rating (1" – 6")
• Stainless Steel 720 psi @ 100°F (49,6 bar @
37,8°C); 480 psi @ 500°F with Teflon packing (33,1 bar @ 260°C); 445 psi @ 650°F with
braided packing (30,7 bar @ 343°C)
• Carbon Steel 740 psi @ 100°F (51,0 bar at 38°C);
600 psi @ 500°F with Teflon packing (41,4 bar
@ 260°C); 535 psi @ 650°F with braided packing
(39,6 bar @ 343°C)
Body Rating (8")
• Stainless Steel 275 psi @ 100°F (19 bar @
38,8°C) and 155 psi @ 550°F (10,7 bar @ 288°C)
• Carbon Steel 285 psi @ 100°F (19,7 bar @
38,8°C) and 155 psi @ 550°F (10,7 bar @ 288°C)
Actuators
• 35M, 55M, 85M, 100M multi-spring actuator (depending on size/pressure drop)
• Direct mount pneumatic piston
• Electric motorized
Turndown Ratio Capability: 100:1
Sizes: 1" (DN25) through 8" (DN200)
1" (DN25) thru 6" (DN150) ANSI 150# / 300#
(PN25/40) Class Wafer Style Valves (bolt-around); 8"
(DN200) ANSI 150# (PN25) Class Wafer Style Valves
(bolt-thru)
Body/Bonnet Connection
• 316 Stainless Steel (ASME SA-479)
• Carbon Steel (SA-105)
Trim Material
• 303 Stainless Steel (8" only)
• 316 Stainless Steel
Seats Materials
• Jorcote/316SS – standard
• Jorcote with 303SS - optional
Yoke Materials
• Ductile Iron (1" - 2")
• NAMUR Cast Iron
Actuator Case Material: Epoxy coated steel
Packing Material
• Spring loaded Teflon V-Ring to 500°F (260°C)
• Grafoil above 500°F (260°C)
Shutoff: ANSI Class IV tightness
Ranges: 3-15, 3-9*, 9-15*, 6-30 psi (0,2–1,0; 0,2–0,6;
0,6–1,0; 0,4–2,1 bar)
* positioner required
Pressure/Temperature Chart
Carbon Steel
Stainless Steel
(55) 800
(55) 800
(41) 600
(34) 500
(28 400
(21) 300
(14) 200
(7) 100
(0)
0
0
(-18)
(48) 700
1" - 6" Size
8" Size
Pressure psi (bar)
Pressure psi (bar)
(48) 700
PTFE Packing
Braided Grafoil Packing
100
(38)
200
300 400 500 600
700
(93) (149) (204) (260) (316) (371)
Temperature °F (°C)
1" - 6" Size
(41) 600
(34) 500
(28) 400
(21) 300
8" Size
(14) 200
PTFE Packing
Braided Grafoil Packing
(7) 100
(0)
-2-
0
0
(-18)
100
(38)
400
500
200
300
(93) (149) (204) (260)
Temperature °F (°C)
600
(316)
700
(371)
Mark 75 Series Wafer Style Control Valves
Cv/Kv vs Travel – Linear
Cv (Kv)
9.5 (8,2)
33 (28)
38 (33)
72 (62)
76 (66)
103 (89)
180 (155)
400 (345)
600 (510)
Flow Characteristics
Linear
Linear
Linear
Linear
Linear
Linear
Linear
Linear
Linear
10%
0.95
3.3
3.8
7.2
7.6
10.3
18
40
60
20%
1.90
6.6
7.6
14.4
15.2
20.6
36
80
120
30%
2.85
9.9
11.4
21.6
22.8
30.9
54
120
180
40%
3.8
13.2
15.2
28.8
30.4
41.2
72
160
240
50%
4.75
16.5
19.0
36.0
38.0
51.5
90
200
300
60%
5.70
19.8
22.8
43.2
45.6
61.8
108
240
360
70%
6.65
23.1
26.6
50.4
53.2
72.1
126
280
420
80%
7.60
26.4
30.4
57.6
60.8
82.4
144
320
480
90%
8.55
29.7
34.2
64.8
68.4
92.7
162
360
540
100%
9.5
33
38
72
76
103
180
400
600
Cv vs Travel curves represent projected performance based on file data. Actual results may vary from system to system.
Cv (Kv) Values
Size
1"
1-1/2"
DN
DN25
DN40
2"
DN50
2-1/2"
3"
4"
6"
8"
DN65
DN80
DN100
DN150
DN200
Linear Cv
9.5
33
38
72
76
103
180
400
600
Linear Kv
8,2
28
33
62
66
89
155
345
510
Equal Percentage Cv
CF
CF
CF
CF
CF
CF
CF
CF
CF
Equal Percentage Kv
CF
CF
CF
CF
CF
CF
CF
CF
CF
CF = Consult Factory for Equal Percentage Requirements
Note: EQP trim available to full linear Cv if programmed through MK16IQ positioner
<
Maximum
Size
1"
1-1/2" – 2"
1"
1-1/2" – 2"
1-1/2" – 2"
2-1/2" – 3"
4"
6"
2-1/2" – 3"
4"
6"
Ratings, PSI (BAR) Without Positioner
Actuator
35M
35M
55M
55M
85M
55M
55M
55M
85M
85M
85M
Teflon
125 (8,6)
125 (8,6)
200 (13,8)
175 (12,1)
250 (17,2)
40 (2,8)
25 (1,7)
25 (1,7)
75 (5,2)
40 (2,8)
40 (2,8)
-3-
Jorcote
150 (10,3)
125 (8,6)
225 (15,5)
175 (12,1)
275 (19,0)
50 (3,4)
35 (2,4)
35 (2,4)
80 (5,5)
50 (3,4)
50 (3,4)
Mark 75 Series Wafer Style Control Valves
<
Maximum
Size
1" – 2"
2-1/2"
1" – 2"
2-1/2" – 3"
4"
6"
1"
1-1/2" – 2"
2-1/2" – 3"
4"
6"
8"
2-1/2" – 3"
4"
6"
2-1/2" – 3"
4"
6"
8"
Ratings, PSI (BAR) With Positioner
Actuator
35M
35M
55M
55M
55M
55M
85M
85M
85M
85M
85M
100M
55M
55M
55M
85M
85M
85M
100M
Teflon
175 (12,1)
150 (10,3)
275 (19,0)
250 (17,2)
200 (13,8)
125 (8,6)
475 (32,8)
425 (29,3)
325 (22,4)
300 (20,7)
200 (13,8)
220 (15,2)
250 (17,2)
200 (13,8)
125 (8,6)
375 (25,9)
300 (20,7)
200 (13,8)
220 (15,2)
Jorcote
200 (13,8)
185 (12,8)
300 (20,7)
275 (19,0)
225 (15,5)
150 (10,3)
500 (34,5)
450 (31,0)
400 (27,6)
325 (22,4)
225 (15,5)
250 (17,2)
275 (19,0)
225 (15,5)
150 (10,3)
400 (27,6)
325 (22,4)
225 (15,5)
250 (17,2)
Note: 25 psi (1,7 bar) air supply for ATC, 45 psi (3,1 bar) for ATO (35 min, 45 max)
Sliding Gate Features & Benefits
Jordan Valve's Sliding Gate Seats
Installed in the widest range of gas, chemical and
steam applications the world over, our pressure
regulators, temperature regulators and control
valves have been providing the following benefits
for over fifty years.
Shorter stroke length than globe or cage designs
• Provides faster response to input signal
changes
• Significantly extends packing and diaphragm
life
• Allows for more compact valve/actuator
assembly
Straight-through flow
• Significantly reduces turbulence, thereby reducing noise and erosion
• Markedly increases rangeability associated
with "flow to open" and "flow to close" designs
• Eliminate valve "chatter" commonly observed
when valve is partially open
Ease of maintenance
• During seat/Cv change (seats are not screwed
or pressed in body)
• Attributable to lightweight, compact design
• Fewer trim components
** ** * * no gasket in 8"
** guides up to 3"
Features
•
Easy installation between flanges with wafer body
•
High flow rates
•
Self cleaning, self lapping seats
•
Reduced noise compared to conventional globe/
cage valves
•
More resistant to cavitation / flashing with straight
through, wafer design
-4-
Mark 75 Series Wafer Style Control Valves
8" Mark 75
with
100M Actuator & MK16IQ Positioner
100M actuator
Can change from ATO - ATC
without disassembling the
actuator
Mark 16IQ Intelligent
Positioner
Cast Iron NAMUR
yoke
ANSI 150# Class bolt
thru body for strength
Sliding Gate trim - multiorifice trim, reducing wear
Straight through flow:
less noise, less wear, better
rangeability, longer seat life
No disc guides
No body gasket required
•
•
•
•
•
•
•
Trim: 316 SST
Seat Materials: Jorcote with 316SS
– no body gasket
Actuator Case: 100M steel
Packing Materials: spring loaded Teflon V-ring, grafoil above 500°F (260°C)
Ratings:
– Stainless Steel 275 psi @ 100°F (19 bar @ 38,8°C) and 155 psi @ 550°F (10,7 bar @ 288°C)
– Carbon Steel 285 psi @ 100°F (19,7 bar @ 38,8°C) and 155 psi @ 550°F (10,7 bar @ 288°C)
Flow Capacity: 600 Cv (522 Kv) Linear and Equal Percentage (determined by positioner)
Maximum Pressure Drop: 250 psi (17,2 bar) with 100M actuator, 12-25 psi (0,83-1,7 bar) bench set
with side mounted positioner
-5-
Mark 75 Series Wafer Style Control Valves
1" thru 3" Mark 75 Series with Cast Body
55/85M epoxy-coated
actuator
Can change from ATO - ATC
without disassembling the
actuator
NAMUR yoke
Shorter stroke length than
conventional globe style,
providing faster response and
extra packing life
Straight through flow:
less noise, less wear, better
rangeability, longer seat life
Semi-lug body
Sliding Gate trim - multiorifice trim
-6-
Mark 75 Series Wafer Style Control Valves
4" thru 6" Mark 75 Series with Bar Stock Body
55/85M epoxy-coated
actuator
Can change from ATO - ATC
without disassembling the
actuator
NAMUR yoke
Shorter stroke length than
conventional globe style,
providing faster response and
extra packing life
Sliding Gate trim - multiorifice trim
Straight through flow:
less noise, less wear, better
rangeability, longer seat life
-7-
Mark 75 Series Wafer Style Control Valves
Dimensions – MK75 with MV1010 Motor
D
B
C
A
Inches
Valve
Size
Metric
Motor
Size
1"
MV1010
1-1/2" MV1010
2"
MV1010
Valve
Size
2-1/2"
3"
4"
6"
Motor
Size
MV1010
VA1020
MV1010
VA1020
MV1020
VA1010
VA1010
VA1020
Dimensions
A
1.24
1.36
1.76
B
C
18.58 2.76
19.09 3.24
19.44 3.98
D
7.13
7.13
7.13
Dimensions
A
1.81
1.81
2.06
2.23
B
21.93
27.17
23.18
28.42
24.23
29.47
—
30.76
C
D
4.36
7.13
5.25
7.13
6.46
7.13
8.62
7.13
Weight
Lbs
Valve
Size
20
22
22
Motor
Size
DN25 MV1010
DN40 MV1010
DN50 MV1010
Weight
Lbs
Valve
Size
32
40
44
52
53
61
69
77
Motor
Size
MV1010
VA1010
MV1010
DN80
VA1010
MV1020
DN100
VA1010
VA1010
DN150
VA1020
DN65
-8-
Dimensions, mm
A
31,5
34,5
44,7
B
472
485
494
C
70,1
82,3
102
D
181
181
181
Dimensions, mm
A
46,0
46,0
52,3
56,6
B
557
690
589
722
615
749
—
781
C
D
111
181
133
181
164
181
219
181
Weight
Kgs
9,1
10,0
10,0
Weight
Kgs
14,5
18,1
20,0
23,6
24,0
27,7
31,3
34,9
Mark 75 Series Wafer Style Control Valves
Dimensions – MK75
D
B
C
A
Inches
Valve
Size
Metric
Act.
Size
35M
55M
35M
1-1/2"
55M
35M
2"
55M
35M
2-1/2"
55M
35M
3"
55M
55M
4"
85M
55M
6"
85M
8"
100M
1"
Dimensions
A
B
C
1.24 10.54
2.76
1.36 10.82
3.24
1.76 11.17
3.98
1.81 14.08
4.36
1.81 14.86
5.25
2.06 17.98
6.46
2.23 19.30
8.62
2.38 21.91 13.75
D
9.50
12.50
9.50
12.50
9.50
12.50
9.50
12.50
9.50
12.50
12.50
15.00
12.50
15.00
15.00
Weight
Lbs
Valve
Size
18
28
20
30
20
30
30
40
42
52
51
61
67
77
131
DN25
DN40
DN50
DN65
DN80
DN100
DN150
DN200
-9-
Act.
Size
35M
55M
35M
55M
35M
55M
35M
55M
35M
55M
55M
85M
55M
85M
100M
Dimensions
A
B
C
31,5
268
70
34,5
275
82
44,7
284
101
46,0
358
111
46,0
377
133
52,3
457
164
56,6
490
219
60,5
557
350
D
241
318
241
318
241
318
241
318
241
318
318
381
318
381
381
Weight
Lbs
8,2
12,7
9,1
13,6
9,1
13,6
13,6
18,1
19,1
23,6
23,1
27,7
30,4
34,9
59,4
Mark 75 Series Wafer Style Control Valves
Ordering Schematic Mark 75
Model No Size
Body Mat'l
1
2
3
4
75
75SP
75TP
Model
Standard
Side Mounted Positioner
Top Mounted Positioner
100
150
200
250
300
400
600
800
Size
1"
1-1/2"
2"
2-1/2"
3"
4"
6"
8" (available with 75SP only)
5 6
7
8
9
10
5&6
W
Y
ZZ
11 12
13
Body Material
Carbon Steel Bar
Stainless Steel Bar
Carbon Steel Cast
Stainless Steel Cast
1&2
I3
I5
ZZ
End Connections
150# / 300# IFE
150# Bolt Thru (8" only)
Non-Standard
3&4
T6
I6
ZZ
Trim
316SS / PTFE Packaging
316SS / 287-I Packaging
Non-Standard
15 16
Seats
Material
316SS / Jorcote
316SS / Jorcote/ Jordanic
17
18
Cv
8
A
B
E
F
H
I
J
K
9.5
33
38
72
76
103
180
400
600
Non-Standard
Consult factory for equal percentage requirements
7&8
CB
SB
CS
S6
14
Range
75, 75TP
A
B
C
D
E
F
G
F
Range
3-15 DIR
3-15 REV
3-9 DIR**
3-9 REV**
9-15 DIR**
9-15 REV**
6-30 DIR
6-30 REV
A
B
DIR
REV
Actuator
3
35M
5
55M
8
85M
75SP
3
5
8
9*
35M
55M
85M
100M
ZZ
Non-Standard
* 8" MK75SP only
** positioner required
9 & 10
B
Diaphragm
Material
Buna-N
Size
3
5
8
9*
ZZ
Non-Standard
* 8" MK75SP only
Continued on next page
-10-
35M
55M
85M
100M
Mark 75 Series Wafer Style Control Valves
Ordering Schematic Continued
11 & 12
A3
A5
A8
A9*
ZZ
* 8" MK75SP only
Actuator
35M
55M
85M
100M
Non-Standard
13 & 14
Accessory 1
00
None
AR
Air Regulator
H5
Handwheel 55M Actuator
H8
Handwheel 85M Actuator
H9*
Handwheel 100M Actuator
ZZ
Non-Standard
* 8" MK75SP only
15
D
R
ZZ
Action
Air-To-Close
Air-To-Open
Non-Standard
16
0
3
5
8
9
Z
Accessory 2
None
I/P 35M Act. 4-20 Ma/3-15 psi
I/P 55M Act. 4-20Ma/3-15 psi
I/P 85M Act. 4-20Ma/3-15 psi
I/P 35M/55M/85M Act. 4-20Ma/6-30 psi
Non-Standard
-11-
17
0
F
Z
PED Compliance
Not Required
CE Category 1
Non-Standard
18
0
A
B
C
D
E
F
G
H
J
Z
SMP
None
SMP DIR/REV 3-15
SMP DIR/REV 3-9
SMP DIR/REV 9-15
SMP/IP DIR/REV 4-20
SMP/IP DIR/REV 4-12
SMP/IP DIR/REV 12-20
MK16IQ DIR/REV 4-20 (Hart & FM-App)
MK16IQ-B DIR/REV 4-20 (with gauges)
MK16IQ-FF DIR/REV 4-20 (Fieldbus w/gauges)
Non-Standard
MK75/0511/10K/AB
Mark 75 Series Wafer Style Control Valves
Ordering Schematic MK75MV with Motor Valve
Model No Size
Body Mat'l
1
2
75MV
Model
with Motor Valve
100
150
200
250
300
400
600
Size
1"
1-1/2"
2"
2-1/2"
3"
4"
6"
CB
SB
CS
S6
Body Material
Carbon Steel Bar
Stainless Steel Bar
Carbon Steel Cast
Stainless Steel Cast
1&2
I3
ZZ
End Connections
150# / 300# IFE
Non-Standard
3&4
T6
I6
ZZ
Trim
316SS / TEF Packaging
316SS / 287-I Packaging
Non-Standard
5&6
W
Y
ZZ
Seats
Material
316SS / Jorcote
316SS / Jorcote/ Jordanic
3
4
Cv
8
A
B
E
F
H
I
J
5 6
7
8
9
10
11 12
13
14
15
7&8
42
41
12
VS
V1
NF
NN
ZZ
Range
4-20mA
4-12mA
12-20mA
0-5 VDC
0-10 VDC
On/Off
No Motor
Non-Standard
9 & 10
A1
A2
ZZ
Actuator/Yoke Feat
MV1010 - 120/240 VAC
MV1020 - 120/240 VAC
Non-Standard
11 & 12
00
SC
XC
Accessory 1
None
Clean for Oil Free
Oxygen Clean
13 & 14
DD
RR
DP
RC
Action
Direct
Reverse
Direct/Fail Open
Reverse/Fail Closed
15
0
F
Z
PED Compliance
Not Required
CE Category 1
Non-Standard
9.5
33
38
72
76
103
180
400
Non-Standard
Jordan Valve a division of Richards Industries
3170 Wasson Road • Cincinnati, OH 45209
513.533.5600 • 800.543.7311 • 513.871.0105 (f)
[email protected] • www.jordanvalve.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement