tkc-1480
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 1
MNEU SSETTING
uper LoLux
lux
0.4
TK-C1480E
1/2" HIGH RESOLUTION COLOUR VIDEO CAMERA
Product Guide
1
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 1
CONCEPT
New TK-C1480E series
When JVC introduced its TK-1280E series and TK-C1380E series to the 1/2" camera market,
they are widely accepted and recognized as standard-setting cameras.
The new TK-C1480E series, which is to maintain market leadership, adopts newly developed
DSP and CCDs, which feature much higher sensitivity, as well as more functions than its
predecessor, the TK-C1380E series. Added functions include: backlighting and remote
surveillance with RS-422A/RS-485 communications.
Features
Using the 1/2-inch EXVIEW CCD permits sensitivities of 0.8 lux (F 1.2, 50%) and 0.4 lux (F
1.2, 25%). When combined with the slow shutter function, these are increased to 0.025 lux (F
1.2, 50%) and 0.0125 lux (F 1.2, 25%), respectively.
Until now it has been difficult to clearly distinguish between bright and dark subjects in the
same view. With the introduction of JVC’s newly developed DSP this shortcoming no longer
exists, making 24-hour surveillance possible.
For remote camera parameter setting in repeat surveillance communication, RS-422A/
RS-485 standards are provided. An easy-to-use parameter setup menu and high-quality
shooting with no backlight, both of which are popular functions of the TK-C1380E, are also
adopted by the new series.
1/2" IT 440,000-Pixel CCD
Super LoLux
480 TV Lines
S/N 50dB
ExDr (Extended Dynamic Range function)
Motion Detection
RS-422A/RS-485 Communication
Auto Black ON/OFF
Slow Shutter for High Sensitivity
It’s Able to Control by RM-P2580
1
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 2
DETAILED FEATURES
Super LoLux Sensitivity
Using a new high-sensitivity CCD
permits Super LoLux photography.
TK-C1380E
0.95 lux, 25%
2.0 lux, 50%
TK-C1480E
0.4 lux, 25%
0.8 lux, 50%
0.025 lux (50% at slow shutter x32)
0.0125 lux (25% at slow shutter x32)
Spectral Response
TK-C1380E (Conventional CCD)
1.0
TK-C1480E (EXVIEW CCD)
1.0
Ye
Ye
Mg
0.8
0.8
Cy
Relative Response
G
0.6
0.4
Mg
0.2
0.0
400
450
500
Cy
0.6
G
0.4
0.2
550
Wave Length (nm)
600
650
700
0.0
400
450
500
550
600
650
700
Wave Length (nm)
Because there is a difference in the spectral response of the CCD between TK-C1380E and TK-C1480E, the
same color reproduction is difficult to obtain. (Of course, we have tried to adjust the color matrix of the
TK-C1480E so that it is as close as possible to that of TK-C1380E.)
2
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 3
DETAILED FEATURES
ExDr
ExDr mode: This is the shutter mode for a subject for which strong light and normal (or low) light conditions
coexist.
The ExDr mode is divided into two further modes:
Manual ExDr mode and Auto ExDr mode.
1 Manual ExDr mode:
Selectable high speed shutter
1/500 to 1/20,000
Other Competitors style: Fixed
Variable contrast level
+5 to -5
Minus (-) direction: The iris is set at strong light.
Plus (+) direction: The iris is set at low light.
Other Competitors style: Auto only
2 Auto ExDr mode:
The iris at the strong light portion and at the low light portion can be automatically detected and the results are
combined to determine the required shutter speed.
Variable contrast level
+5 to -5
Minus (-) direction: Adjusted for strong light
Plus (+) direction: Adjusted for low light
48 area
Auto peak detect → auto shutter
3
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 4
JVC's positioning compared to competing companies
JVC TYPE (ExDr)
EXPANDABILITY SYSTEMS
CCD: SELECT ANY CHIP FROM MARKET
DSP & SOFTWARE: JVC EXCLUSIVE DSP & SOFTWARE
ANY CHIP FROM MARKET
e.g. able to use high
performance CCD like EXVIEW
&
EXCLUSIVE JVC ORIGINAL
DSP AND SOFTWARE SYSTEMS
OTHER MANUFACTURERS’ TYPE
CLOSED CIRCUIT SYSTEMS
CCD: EXCLUSIVE CCD
DSP & SOFTWARE: EXCLUSIVE DSP & SOFTWARE
EXCLUSIVE CCD
HYPER PROGRESSIVE
&
EXCLUSIVE DSP
AND SOFTWARE SYSTEMS
4
5
1/4000
(FIX)
1/4000
(FIX)
MIXED
PICTURE
OUTPUT
WITH 1/60
SHUTTER
MIXED
PICTURE
OUTPUT
WITH 1/60
SHUTTER
1/4000
(FIX)
MIXED
PICTURE
OUTPUT
WITH 1/60
SHUTTER
mixed picture output
under 1/60 shutter
with Gain control
A path
B path
2 path reading
x2times reading
1/50
(FIX)
1/50
MERIT : keep sensitivity(better graduation)
DEMERIT : AGC changeable based on the condition and if it has high light object,
it has noisy picture(S/N)
mixed picture output
under 1/60 shutter
with Gain control
A path
B path
2 path reading
x2times reading
1/50
(FIX)
mixed picture output
under 1/60 shutter
with Gain control
A path
B path
2 path reading
x2times reading
1/50
(FIX)
For WIDE-Dynamic range function
CCD : EXCLUSIVE HYPER PROGESSIVE CCD
DSP : EXCLUSIVE PROCESSING
1/50
1/50
MANUAL ADJUST
POSSIBLE !!
MANUAL ADJUST
POSSIBLE !!
MERIT : better S/N level
DEMERIT : reduce the sensitity(reduce the graduation)
PAL long shutter : 1/100(FIX)
auto 1/10000
manual 1/20000
MIXED
PICTURE
OUTPUT
WITH 1/60
SHUTTER
MIXED
PICTURE
OUTPUT
WITH 1/60
SHUTTER
RAM
(MEMORY)
Variable
(Auto &
manual)
RAM
(MEMORY)
1/100
(FIX)
x 2times reading
Variable
(Auto &
manual)
x 2times reading
1/100
(FIX)
For WIDE-Dynamic range function
CCD : USE ANY CCD FROM MARKET(JVC USES EXVIEW)
DSP : EXCLUSIVE PROCESSING
1/50
Normal Shutter
1/50
1/50
2. JVC STYLE (PAL)
Normal Shutter
1/50
1. OTHER MANUFACTURER STYLE (PAL)
NORMAL LIHGT
SHUTTER
HIGH LIGHT
SHUTTER
DIFFERENCE BETWEEN OTHER MANUFACTURER AND JVC TYPE FOR WIDE-DYNAMIC RANGE
Variable
(Auto &
manual)
MANUAL ADJUST
POSSIBLE !!
MIXED
PICTURE
OUTPUT
WITH 1/60
SHUTTER
RAM
(MEMORY)
x 2times reading
1/100
(FIX)
1/50
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 5
DETAILED FEATURES
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 6
High-speed side shutter operation for ExDr-AUTO
SHUTTER
LENS
(Auto Iris Operation)
Sees the highest peak on
the divided-by-48 portion.
Too bright
as a whole
Too dark
as a whole
Adjusts (and sets) the
shutter so that the peak
value may become a
certain level.
Stops down
the lens
Opens
the lens
Simultaneous operation
When the lens is fully
open because the area is
too dark as a whole.
Lowers the high-speed
side shutter speed
(down to 1/100 second)
Automatic
If still too dark for a speed
of 1/100 second, then WD
is set to OFF (WD-AUTO).
And at a speed of 1/50
second AGC is turned ON.
(Note) Slow shutter mode is not available for WD-ON and manual operation.
Auto Exdr, Auto and Normal modes are available for Sense Up operation.
Manual Exdr and Manual modes are not available for Sense Up operation.
6
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 7
DETAILED FEATURES
Contrast MIX method (or Contrast Mixing)
Low
brightness
side
(Long
Shutter)
Input
Input
200%
200%
100%
100%
A
Compression
Output
High
brightness
side
(Short
Shutter)
Input
Input
200%
200%
100%
100%
+
Output
Compressed
to 1/2
Output
Output
MIX
Input
200%
Level on the Menu shows the value of changing (A).
High
100%
Contrast
level
adjust (or
adj.)
menu on
the Menu
+5
+4
+3
+2
+1
normal
-1
-2
-3
-4
-5
565mV
540mV
515mV
490mV
465mV
440mV
415mV
390mV
365mV
340mV
315mV
80%
77%
74%
70%
66%
63%
59%
56%
52%
49%
45%
Low
This is multiplied
by the gamma and
the knee. Input
Output
200%
High
100%
A
Low
Output
*A place where low brightness is detected
7
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 8
Slow Shutter
Available (selectable) modes are: Off, x2, x4, x8, x16, x24 and x32. The same picture is stored in multiple fields
to obtain increased sensitivity.
In this case a decrease of resolution of 50% results when only even fields are used (odd fields are not used).
P.S. Priority Mode
The slow shutter speed can be used when AGC is ON.
1 Motion
AGC is turned ON first, followed by slow shutter-ON.
(Motion picture priority mode)
2 Picture
If AGC is turned ON first, noise tends to be introduced.
To prevent noise slow shutter is turned ON prior to turning AGC ON. If, however, the prime requirement is
sensitivity, AGC is turned ON first (with no consideration given to increased noise).
8
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 9
DETAILED FEATURES
Motion Detect
It is possible to set freely the area where MOTION DETECTING functions.
MO T I O N DE T EC T
MOD E
L E VE L
AR EA E D I T . .
AL ARM T I M E
DE MON S TRA T I ON . .
1.
Select the item AREA EDIT on
the MOTION DETECT screen.
2.
Press the SET button.
OFF
NORMAL
10s
The setting screen is brought up.
3.
MOTION DETECT screen
Select the area not subject to
detection using the
button.
The area flashing ON and OFF in black
and white moves.
flash
4.
Press the SET button.
The area not subject to detection is set,
and it turns gray (lights up).
To cancel the set area, press the SET
button again.
Setting screen
lights gray
flash
5.
Repeat items 3 and 4 above.
6.
Upon completion of setting,
press the MENU button.
The screen returns to the MOTION
DETECT menu.
MEMO
Indicated positions on the screen are rough
guides.
Be sure to check and conform the positions
on the actual screen.
* It is possible to check and confirm the set
areas on the DEMONSTRATION screen.
The detection area is shown in gray.
9
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 10
Communication
Communication complies with RS-422A/RS-485 standards.
Setup menu is given below.
Main menu Communication menu
Be sure to make the necessary settings prior to connection.
MENU
S YNC A DJ UST . .
A L C S E T T I NGS . .
V I DEO A DJ UST . .
MODE S E L ECT . .
MOT I ON D E T E CT . .
COMMUN I CAT I ON . .
F A C TORY SET T I NGS . .
SHUT TE R ( E x DR )
SYNC A D J US T
V PHASE
H PHASE
S C COARS E
S C F I NE
0
0
0
1 28
S HUT T ER SPEED
F AST L I M I T
E x D R L EV E L
M . E x D R SPEED
1 / 120
– ––
– ––
– ––
A L C SE T T I NGS
I R I S L E VE L
A V E RA GE : P EAK
S H UT T ER ( E x DR )
A G C MODE
S E NS E U P
P R I OR I T Y
B LC
V I DE O ADJ U ST
WH I T E BAL A NCE
COL OUR L E V E L
E N HANCE L E V E L
P E DE ST AL LE V E L
AU T O BL AC K C T L
NORMAL
8:2
N O RMAL
2 0 dB
OF F
–––
OF F
WH I T E BALANC E CONT RO L
ATW
NORMAL
NORMAL
NORMAL
OF F
AWC SE T . .
R :
Mg :
:
:
B
G
MODE S EL E C T
CAMERA T I T L E ED I T . .
RE V ERS E MODE
OF F
AL M . T I T L E S I Z E
DOUBLE
AL ARM COLOUR
WH I T E
MO T I O N DE T EC T
MOD E
L E VE L
AR EA E D I T . .
AL ARM T I M E
DE MON S TRA T I ON . .
C AME R A T I T L E
0 1 2 3 4 5 6 78 9 - : / . ,
AB C DE F G H I J K L MN O P
QR S T U VWX Y Z
a b c d e f g h i j k l mn o p
q r s t uvwx y z ’
Ä ÖÜ Â Ê Î Ô Û Ç Ñ
ä ë ï ö üâ ê î ô û á é í óú
à è ì òùçñß ¡ ¿
OFF
NORMAL
10s
C OMMUN I C A T I O N
S T YLE
MA C H I NE
ID
M . DROP
1
WIDE
T i t l e
TELE
Di s l ay
F A C T ORY SE T T I NGS
CA N CE L
CL E AR ( W I T HOUT T I T L E )
C L E AR ( AL L )
D AT A CL EARE D
10
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 11
DETAILED FEATURES
Connect cables as shown below.
Setting the switches
Select the synchronization method of the
camera image.
Set the switch on all cameras to LL (Line Lock)
and match with the V. PHASE.
EXT TERM-OFF
INT/GL
DUPLEX
RX TERM-OFF
SET
AWC
MENU
CAMERA
SETUP
EXT TERM-OFF
ON
LL
SIMPLEX
ON
INT/GL
DUPLEX
RX TERM-OFF
ON
LL
SIMPLEX
ON
NOT USED
NOT USED
VIDEO
DC
Set this switch to the DUPLEX
* If the setting is changed, be absolutely sure to
switch on the power again.
Set this switch to ON (signal termination ON)
only on the camera placed at the end of the
control signal cable.
Set to OFF on all other cameras.
IRIS
Setting on the MENU screen
* If the setting is changed, escape from the menu screen once, and definitely switch on the power again.
Set to M.DROP
C OMMUN I C A T I O N
Set to M.DROP when the RM-P2580E is used
S T YLE
M . DROP
as a remote control unit. When controlling from
MA C H I NE I D
1
another machine, make sure that it matches
the communication system used.
MACHINE ID setting switches
Set this item to match the RM-P2580E VIDEO
INPUT terminal number for each camera.
When connecting
● Turn OFF the power supply to all equipment to be used before making connections.
● Carefully read the Instructions for each piece of equipment to be used before making
connections.
● For the appropriate connection cables and the length of these, carefully read “Connections on
the back” on page 16 of Instruction Manual.
● The control signal cable cannot be used for loop connection.
Connecting the control signal cable
(Use a twisted-pair cable for connection. )
Camera 1
control signal
connection terminals
RM-P2580E
RM-P2580
TX+ A
TX B
RX+ C
RX D
A RX +
B RX
C TX +
D TX
Camera 2
control signal
connection terminals
TX+ A
TX B
RX+ C
RX D
11
Connect:
Camera TX+ to RM-P2580E RX+
Camera TX– to RM-P2580E RX–
Camera RX+ to RM-P2580E TX+
Camera RX– to RM-P2580E TX–
The A B C D marks indicated on both the
camera terminals and the RM-P2580E terminals facilitate correct connections. Connect
the terminals with identical marks.
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 12
Auto Black
Using the Auto Black function the pedestal level can be controlled automatically when AGC is turned ON.
Auto Black Operation (or Control) (ON)
Changes the SET UP (default of pedestal) position in accordance with the AGC gain.
The SET UP position stays at +5 (100 mV approx.) for a PEDESTAL-on-the-MENU of +5 (Max.) irrespective of
the AGC, while it varies from -5 (0 mV) to +5 (100 mV) in accordance with the AGC gain for a PEDESTAL-onthe-MENU of -5.
Pedestal
Level
100mV
Pedestal = +5
50mV
Pedestal = 0
0mV
Pedestal = -5
0dB
10dB
20dB
AGC Gain
The thick line indicates the default (set at factory)
Pedestal Setting (Pedestal = 0) + AGC ON (GAIN = 20dB).
12
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 13
DETAILED FEATURES
White Balance Adjustment
Two white balance modes available to use by TK-C1480.
1. ATW - Automatice White Balance (Auto mode)
Always white balance traced depending on the colour temperature
2. AWC - Automatice White Balance control (one push mode)
It's able to have white balance each object scene. Also sometimes there might be not able to have white
balance with ATW. Such case, please use AWC.
After that, manual painting possible (2Axis) with set up by user.
WH I T E BALANC E CONT RO L
AT W or AWC
WH I T E BALANC E CONT RO L
AWC SE T . .
R :
Mg :
:
:
B
G
In addition, AWC is possible by pushing set button (apx.2sec) on the side switches of camera.
13
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 14
COMPARISON
SPECIFICATION
TK-C1380E
TK-C1480E/1481EG
Image Sensor
Number of Pixels
Video S/N Ratio
Minimum Illuminations
1/2"
752 (H) x 582 (V)
48dB (AGC OFF)
2.0 lux (50% F1.2 AGC ON)
0.95 lux (25% F1.2 AGC ON)
Internal
Line-Lock
Full Genlock
YES
YES
YES
470 TV Lines
Composite video signal
YES
ATW
MANUAL
OFF/9dB/18dB/Super AGC
ON/OFF 6 patterns (2 edits)
1/50 — 1/100,000 sec.
(ON/OFF switchable)
1/100, 1/250, 1/500, 1/1,000,
1/2,000, 1/4,000, 1/10,000 sec.
24 characters
ENHANCE, IRIS, COLOUR, HUE,
PEDESTAL, Av:Pk Levels
NO
1/2" Super LoLux Type
752 (H) x 582 (V)
50dB (50%, AGC OFF)
0.8 lux (50% F1.2 AGC ON)
0.4 lux (25% F1.2 AGC ON)
Internal
Line-Lock
Full Genlock
YES
YES
YES
480 TV Lines
Composite video signal
YES
ATW
AWC (Paint possible)
OFF/10dB/20dB/Super AGC
ON/OFF 6 patterns (2 edits)
1/50 — 1/100,000 sec.
(ON/OFF switchable)
1/100, 1/250, 1/500, 1/1,000,
1/2,000, 1/4,000, 1/10,000 sec.
24 characters
ENHANCE, IRIS, COLOUR,
PEDESTAL, Av:Pk Levels
YES
200X (Max. at Auto)
400X (Max. at Manual)
NO
YES (Max.: X32)
NO
YES (RS-422A/RS-485 by menu)
Video iris (side 4-pin switch)
DC iris (side 4-pin switch)
C/CS mount
-10°C to 50°C (operation)
0C° to 40°C (recommend)
Less than 90%
580g
DC12V/AC24V/AC230V (1481EG)
63 x 70 x 138 mm
Sync Method
L.Lock Phase Adjust
H Phase Adjust
SC Phase Adjust
Horizontal Resolution
Video Output
Y/C Output
White Balance
AGC
BLC
AES
Electronic Shutter
Camera ID
Set-Up Menu
Wide Dynamic
Dynamic Range
Digital Zoom
Slow Shutter
IR ON/OFF
Communication
Lens
Lens Mount
Ambient Temperature
Ambient Humidity
Weight
Power Requirement
Dimensions (H x W x L)
NO
NO
NO
NO
Video iris (rear)
DC iris (side)
C/CS mount
-10°C to 50°C (operation)
0C° to 40°C (recommend)
Less than 90%
640g
DC12V/AC24V/AC230V
67 x 70 x 148 mm
14
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 15
COMPARISON
Dimensions (Unit: mm)
TK-C1380E
TK-C1480E
1.5
U1-32
148
159
63
138
55
35
55
70
15
149
70
BF LOCK
DIGITAL
COLOR VIDEO CAMERA
42
71
41
1/4-20 UNC
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 16
CONTROLS, CONNECTORS AND INDICATORS
TK-C1480E
TK-C1380E
2
1
3
4
5
7
6
1 Lens Mount
This means to attach the lens.
This is applicable to both the C-mount lenses (1/2 inch)
and CS-mount lenses (1/2 inch).
2 Backfocus Adjustment Ring
1 Camera Mounting Holes (1/4-inch)
2
3
4
5
Use one of these threaded holes when mounting the
camera on a mount or turret. Two threaded holes are
provided on the front and rear and can be selected
according to the circumstance.
Camera Mounting Bracket Locking Screws (x3:
M2.6x5mm)
Do not use any screw longer than 5 mm.
Camera Mounting Bracket
The bracket has been attached on the bottom of the
cameras before shipment. It can also be attached on the
top according to the circumstance.
To re-attach the bracket use the threaded holes at the
top, with the 3 camera mounting bracket locking screw
2.
Backfocus Adjustment Ring
This ring both allows the adjustment of the backfocus to
and switch as the lens mounting method C and CS.
Loosen the BF LOCK screw 5 by turning it
counterclockwise before turning this ring, and be sure to
secure screw 5 by turning it clockwise after turning this
ring. The TK-C1380/TK-C1381 has been adjusted to the
optimum position for the C mount before shipment.
[BF LOCK] Backfocus Locking Screw
This screw locks the backfocus adjustment mechanism.
Adjusting the back focus during lens installation.
When readjustment is required, loosen the locking
screw 3 by turning it counterclockwise and turn the
back focus adjustment ring 2 .
After the adjustment, tighten the locking screw 3
again.
The TK-C1480 has been adjusted to the optimum
position for the C-mount system before shipment.
3 [BF LOCK] Back Focus Locking Screw
This serves to fix the back focus-adjusting ring.
4 Camera-Mounting Bracket
The bracket has been attached on the bottom of the
camera before shipment. It can also be attached on
the top according to the circumstance.
To re-attach the bracket use the threaded holes at the
top, with the camera mounting bracket locking screws
7 .
5 Camera-Mounting Screw Hole (1/4 inch)
Use this hole when mounting the camera
onto a fixer, pan/tilt unit, and the like. (Use a
screw shorter than 7 mm.)
MAX.
7mm
6 Rotation-Preventive Hole
Make use of this rotation-preventive hole to prevent
any fall when mounting the camera. Make sure that
the camera is securely mounted.
7 Camera Mounting Bracket Fixing Screws (×2: M2.6
× 5 mm)
Do not use any screws longer than 5 mm.
16
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 17
CONTROLS, CONNECTORS AND INDICATORS
TK-C1380E
TK-C1480E
6 Lens Mount
7
! @#
The lens mount is compatible with C-mount lenses (1/2
and 2/3 inches) and CS-mount lenses (1/2-inch).
[DC IRIS] DC Iris Connector
Connect to an auto-iris lens which does not incorporate
an EE amplifier.
$
SET
AWC
CAMERA
SETUP
MENU
ON
LL
SIMPLEX
ON
EXT TERM-OFF
INT/GL
DUPLEX
RX TERM-OFF
NOT USED
%
^
&
*
These functions such as ! $ of TK-C1480E
are not available on TK-C1380E.
VIDEO
DC
8
IRIS
90
8 Cover
The cover opens if it is pulled to the left while being
pushed.
9 [VIDEO/DC] Iris Selector Switch
This is set according to the type of lens when an
automatic iris control lens is used.
VIDEO: In case of lens with EE amp built-in.
DC:
In case of lens without EE amp built-in.
(VIDEO: At time of factory shipment)
10 [IRIS] Iris Terminal
This is connected to an automatic iris control lens.
11 [MENU] Menu Button
When the button is pressed, a menu screen is brought
up.
12 [SET/AWC] Set. Auto White Control Button
SET: Press this button to display a sub-menu.
AWC: If this button is kept pressed for more than 1
second, a one-push-auto-white-balance
function works and sets the white balance.
Once it is set, even if colour temperature
changes, white balance does not change. It is
also possible to make fine adjustments on the
set white balance.
13 [ , , , ] Up-and-Down, Left-and-Right Button
These buttons select items on the menu screen and
change a set value.
14 [EXT.TERM-ON/OFF] Terminal On/Off Switch of
External Synchronization Signal
This is a terminating ON/OFF switch for the external
synchronization input signal.
When this is switched ON, termination is executed via
a 75 Ω resistor.
ON: terminates at 75Ω.
OFF: does not terminate at 75Ω.
(ON: At time of factory shipment)
17
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 18
TK-C1380E
8 [SYNC IN] Sync Signal Input Connector
9
0
.
This BNC connector accepts the input of an external
sync signal such as a composite video (VBS) or black
burst (BB) signal. When a sync signal is input into this
connector, the camera operation is automatically
synchronized with the external sync signal.
The 75-ohm termination of this connector can be
switched on/off on the menu screen as required.
[VIDEO OUT] Video Signal Output Connector
This BNC connector outputs a composite video signal.
Connect this to the video input connector of a video
mounter, switcher, etc.
[POWER] Power Indicator Lamp
This lights when power is supplied to the camera.
TK-C1480E
15 [INT/GL, LL] Selector Switch for Synchronizing
System
This switch can set a synchronizing system of the
camera.
INT/GL:
This is set for internal synchronization (INT) or external
synchronization (GL).
LL (Line Lock):
The camera’s vertical synchronization is locked to the
AC 24V power line frequency.
When switching between multiple cameras using a
switcher, selecting this mode and adjusting the vertical
phase can reduce the monitor sync disturbances
occurring when the camera image is switched. (This
cannot be used in regions where the power frequency is
50 Hz.) (INT/GL: At time of factory shipment)
16 [ D U P L E X , S I M P L E X ] S e l e c t o r S w i t ch f o r
Transmission System
If the setting is changed, be absolutely sure to switch
on the power again.
DUPLEX:
This switch sets to DUPLEX when the transmission
between the camera and a remote control unit is in a
duplex system (two-way).
SIMPLEX:
This switch sets to SIMPLEX when the transmission
between the camera and a remote control unit is in a
simplex system (one-way).
(DUPLEX: At time of factory shipment)
17 [RX.TERM-ON/OFF] RX Signal Terminal ON/OFF
Switch
This sets whether or not the signal between RX + and
RX – on the back 20 should be terminated at the value
of 110Ω resistance.
ON: terminates.
OFF: does not terminate.
If the system including the camera is the M.DROP
(Multi-drop, RS-485) system, only the camera mounted
at the terminal of control signal cable is set to “ON”
and the other camera is set to “OFF”. In case of the
M.DROP system, it becomes necessary to set the
Machine ID.
If the system including the camera is the P TO P (Point
to Point, RS-422A) system, set this switch of all the
cameras to “ON”.
The item STYLE on the COMMUNICA-TION screen
sets M.DROP or P TO P
(ON: At time of factory shipment)
18 NOT USED
This cannot be used. Do not switch.
18
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 19
CONTROLS, CONNECTORS AND INDICATORS
TK-C1380E
TK-C1480E
(
)
q
! [Y/C OUT] Y/C Output Connector
2
C A
2
I A ED
AC24
DC12
(
E
E)
1
(E
E)
This 4-pin connector outputs the luminance and
chrominance signal.
Pin configuration of Y/C OUT connector
GD
A
A
t
B
C
D
/C
C I
r
w
IDE
EE I
CI
MA A
E
e
19 [DC 12V, AC 24V] Power Input Terminals
@ [CAMERA SET UP] Camera Set-up Screen
#
$
Operation buttons
These buttons are used in the set-up operations.
[VIDEO IRIS] Video Iris Connector
Connect to an auto-iris lens incorporating an EE
amplifier.
[DC12V/AC24V] Power Input Connector
(TK-C1380E only)
Connect a DC 12 V±10% or AC 24 v±10%, 50/60 Hz
power supply.
To input DC 12V or AC 24V power.
20 [TX+A , TX-B , RX+C , RX-D ] Control Signal
Connection Terminals
Terminals for inputting signals with electrical
characteristics conforming to the EIA/TIA RS-422A or
RS-485 standard.
17 RX.TERM switch
21 [AUX, GND] Auxiliary Output Terminals
If any change occurs in the area that was set on the
MOTION DETECT screen, these terminals output
signals. Open collector output of a LOW pulse for
between 500 ms and 1,000 ms. Max voltage 30V,
current 30 mA.
22 [Y/C OUT] Y/C Output Connector
This 4-pin connector outputs the luminance and
chrominance signal.
• Pin configuration of Y/C OUT connector
4
2
% Power Cable (for TK-C1381EG only)
Connect to the commercial AC 230V outlet
3
Pin No.
Signal
1
1
2
3
4
GND
GND
Luminance (Y, 1 V(p-p), 75Ω)
Chrominance (C, 0.3 V(p-p), 75Ω)
23 [VIDEO OUT] Video Signal Output Connector
This BNC connector outputs a composite video signal.
Connect this to the video input connector of a video
monitor, switcher, etc.
24 [POWER] Power Indicator Lamp
This lamp lights when power is supplied to the camera.
25 [SYNC IN] Sync Signal Input Connector
This BNC connector accepts the input of an external
sync signal such as a composite video (VBS) or black
burst (BB) signal.
When a sync signal is input into this connector, the
camera operation is automatically synchronized with
the external sync signal.
To terminate this connector at 75Ω, turn ON the
EXT.TERM switch 14 .
19
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 20
SPECIAL SETTINGS BY JVC SERVICE CENTER
Special Settings by JVC Service Center
It is able to have the following settings by JVC service center absolutely.
1. CCD SPOT Compensation
It is possible to compensate the CCD spot up to 3 blemish under ExDr off mode.
2. Level of Auto ExDr
Normally it is not able to change the shutter speed for Auto ExDr mode. However, it is able to have
a little change from default under small tolerance.
For further information, please call to JVC service center.
20
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 21
MINI SYSTEM
CAMERA 1
C OMMUN I C A T I O N
CAMERA MENU
VIDEO
S T YLE
MA C H I NE
ID
M . DROP
1
SETUP
POSITION SETUP..
CAMERA..
CONTROL UNIT..
BF LOCK
DIGITAL
COLOR VIDEO CAMERA
ID:01
CAMERA 8
VIDEO
MONITOR
BF LOCK
DIGITAL
COLOR VIDEO CAMERA
ID:08
RS-485
RX+ RX- TX+ TX-
VIDEO
IN
Hold
Setting Multi-drop
ALARM UNIT
TO
CAMERA
PARALLEL ALARM
UP TO 16 POSITIONS
RM-P2580
TO CAMERA
RX+ RX
RX
RX- TX
TX+ TX
TX-
COM
1
2
3
4
5
6
7
8
DATA I / O
UNIT
CAMERA
COM 9/1 10/2 11/3 12/4 13/5 14/6 15/7 16/8 COM AUTO ALARM COM SW COM
SERIAL-1
SERIAL-2
POWER
OFF
ON
1
AC
2
3
4
VIDEO INPUT
5
6
7
8
MONITOR MONITOR
OUTPUT OUTPUT
2
1
INPUT
1 2 3 4 5 6 7 8
ON
1
2
Sample
3
4
5
VIDEO OUTPUT
6
7
8
CAM SW
Sample
VIDEO
IN
1 2 3 4 5 6 7 8
ON
Camera 1
monitor
Camera 4
monitor
SPOT
SPOT
REC
REC
STOP
REC
CHECK
EJECT
OPERATE
DIP SW 1 “OFF” (A mode)
DIP SWITCH
21
VCR
OPERATE
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 22
MINI SYSTEM
CAMERA 1
C OMMUN I C A T I O N
ID
M . DROP
1
BF LOCK
DIGITAL
COLOR VIDEO CAMERA
ID:01
CAMERA 2
RS-485
BF LOCK
DIGITAL
COLOR VIDEO CAMERA
RX+ RX- TX+ TX-
ID:02
CAMERA 3
Hold
Setting Multi-drop
BF LOCK
DIGITAL
COLOR VIDEO CAMERA
CAMERA MENU
ID:03
SETUP
POSITION SETUP..
CAMERA..
CONTROL UNIT..
DIP SWITCH
1 2 3 4 5 6 7 8
ON
DIP SW 1 “OFF” (A mode)
PARALLEL ALARM OUT
(Up to 8 positions)
MONITOR
PARALLEL ALARM UNIT
PARALLEL ALARM IN
RS-485
8 cameras x 64 positions
TO CAMERA
RX+ RX
RX
RX- TX
TX+ TX
TX-
COM
1
2
3
4
5
6
7
8
DATA I / O
UNIT
CAMERA
COM 9/1 10/2 11/3 12/4 13/5 14/6 15/7 16/8 COM AUTO ALARM COM SW COM
SERIAL-1
SERIAL-2
POWER
CAMERA
MENU
DISPLAYED
OFF
ON
1
AC
2
3
4
VIDEO INPUT
5
6
7
8
MONITOR MONITOR
OUTPUT OUTPUT
2
1
INPUT
1 2 3 4 5 6 7 8
ON
1
2
3
4
5
VIDEO OUTPUT
6
7
8
RM-P2580
REC
IN
REC
STOP
REC
CHECK
EJECT
OPERATE
OPERATE
CASCADE
S T YLE
MA C H I NE
VIDEO VCR
IN
CAM SW
REC
REC
VIDEO
SW-D7000
MONITOR OUT
Sample
ALARM
UNIT
1
2
3
4
5
6
7
8
9
STOP
REC
CHECK
EJECT
OPERATE
OPERATE
VCR
Sample
FIXED CAMERAS
MONITOR
22
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 23
REMOTE CONTROL SOFTWARE
JVC Remote Control Software
Remote control software (RS422A type) is available by JVC as a purpose of demonstration at free.(The
performance is not guaranteed by JVC due to demonstration purpose. Also not able to open source code.)
The following is GUI image
Option Dialog
Menu
Features
1. Camera control possible by RS422A interface
2. Video image output available on the GUI using video card or it is able to connect from camera to video
monitor with BNC.
Connections
1. Remote control ------ Please prepare locally converter from RS422A to RS232C.
After execute JVC software,please have right click and select options settings. Kindly check COM port
setting.
The below is just example.
CAM
Converter
PC
RS422A
RS232C
RS232C
TX+ ----------RX+
TX- -----------RXTX ------------RX
RX+ ----------TX+
RX -----------TX
RX- ----------TXGND ---------GND
Refer to Converter, please kindly check with instruction manual of conveter because depending on the
converter, the connection between PC and converter is different.
2. Video card ------ Please arrange locally video card(PCI bus or PCMCIA type) and install the driver into PC.
After execute JVC software, please have right click and select options settings. Then kindly select driver in
capture device.
Camera Controls
By GUI of this software, it's able to set up ExDr/shutter, Iris/BLC, AGC/SENS UP (slow shutter), Auto EXP, white
balance, video adjustment,reverse image, camera ID. However, it is not possible full set up. So to have full set
up, please use camera menu in GUI and select&set parameters by cursol.
23
TK-C1480Manual.xprNew 01.10.29 5:27 PM ページ 24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising