Instructions - Siren with Air Horn
WIRING DIAGRAM
Installation Manual
SHO-ME
®
ELECTRONIC SIREN
Model 30.2109
Manufactured in the U.S.A
Other quality products manufactured by SHO-ME®
Speakers; LED Lights; Strobe Lights (Directional and 360º);
Headlight Flasher Kits; Full size LED Light Bars;Mini LED Light Bars;
Mini-Bars; Custom Switch Panels; Spot and Flood Lights;
6 Volt Rechargeable Lights; Map Lights; Megaphones;
Accessory Outlets; Bucket Lights
and many more Components and Accessories.
P.O. Box 543 • 804 E. Hwy 248 Cassville, MO 65625-0543
Local and International Numbers
Phone: 417-847-4791
Fax: 417-847-2222
U.S. and Canada Toll-Free Numbers
Phone: 800-641-4098
Fax: 800-526-1240
ELECTRONIC SIREN
MODEL 30.2109
INTRODUCTION
The 30.2109 siren consists of an amplifier which powers
one 100 watt RMS speaker. The amplifier, because of its small
physical size, mounts conveniently in a remote position from the
function control switch.
The 30.2109 siren system includes one center-off rocker
switches that allows the operator to select the WAIL or YELP
functions. The momentary switch allows the operator to sound the
AIR HORN .
INSTALLATION OF POWER AMPLIFIER
Select a location suitable for installation of the amplifier.
This area must be free from moisture, heat, and abuse. DO NOT
MOUNT IN THE ENGINE COMPARTMENT. Using the amplifier
as a template, mark the location of the mounting holes. Drill holes
at these locations to assist in starting the mounting screws
provided. All installations are the sole responsibility of the buyer.
POWER INPUT CONNECTIONS
Connect the supplied black wire to the terminal on the siren
marked “GROUND”. Connect the other end of the black wire to
ground. The negative terminal of the battery is a preferable
location. Connect the supplied red wire to the terminal on the
siren marked “+ 12 VOLTS”. This terminal on the siren connects
directly to the on board 20 amp fuse. Connect the other end of the
red wire to a positive source. To protect the wiring going to the
siren, install an in-line fuse or circuit breaker on the end of the wire
as close to the positive source as possible. The current draw of
the siren during operation is approximately 15 amps, when
supplied by 13.8 volts. The current draw of the siren when power
is applied, but no functions are selected, is approximately .03
amps.
CONTROL SWITCH
Select a location suitable for installation of the control
switch. The area selected should provide ease of operation and
must not interfere with normal operation of the vehicle or
deployment of air bag. Using the switch bracket as a template,
mark the location of the mounting holes. Drill holes at these
locations to assist in starting the mounting screws provided.
CONTROL SWITCH CONNECTIONS
Connect the wires from the control switch to the terminals
on the siren as shown in the diagram. By applying +12 volts to
one of the terminals, the corresponding sound will be produced.
Connect the green wire from the switch to the terminal on the
siren marked “WAIL”. Connect the brown wire from the switch to
the terminal on the siren marked “HORN”. Connect the yellow wire
from the switch to the terminal on the siren marked “YELP”. Run
red wire from terminal marked “+12 VOLTS Input” to power
source. Connect White wire from switch panel to terminal marked
“+12 VOLTS to switches”.
SPEAKER CONNECTIONS
Use only one 100 watt speaker with an 11 ohm
impedance. Connect one conductor of the 16-2 wire supplied to
the terminal on the siren marked “SPKR COMMON”. Connect
the second conductor of the 16-2 wire to the “100 WATT”
terminal on the siren.
WARRANTY
Merchandise returned under warranty shall be subject to
factory inspection and repaired, replaced, or credited at Able 2
Products Company, Inc.’s option. Water, condensation, or
negligence will VOID warranty. This unit’s warranty period is for
2 years parts and labor.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement