Toshiba DK 8 DK 16 I M Manual

TOSHIBA SYSTEM PRACTICES
DIGITAL KEY TELEPHONE SYSTEMS
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
NOT DK 16E
PROGRAMMING PROCEDURES
CHAPTER ONE
INTRODUCTION
DK8-SR-SYSRECR1
4016078
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
TABLE OF CONTENTS
PARAGRAPH
1
2
3
3.10
3.20
3.30
4
5
SUBJECT
PURPOSE ...................................................................................................
ORGANIZATION .........................................................................................
GENERAL PROGRAMMING INSTRUCTIONS...........................................
Programming Data Entry Overview .......................................................
Programming Data Variations ................................................................
Preparing the System for Programming ................................................
AFTER INITIALIZATION ..............................................................................
TELEPHONE BUTTON LABELS .................................................................
PAGE
1-1
1-1
1-1
1-1
1-2
1-6
1-8
1-8
TABLE LIST
TABLE
1-A
1-B
1-C
1-D
1-E
1-F
1-G
1-H
SUBJECT
SIMPLE PROGRAM: PROGRAM 33 (STATION HUNTING) .....................
MULTIDIMENSIONAL PROGRAM: PROGRAM 30 (STATION
CLASS OF SERVICE) ................................................................................
PROGRAM 90/INITIALIZING PROGRAMS 00 ~ 97 ..................................
INITIALIZATION PROGRAM 92/INITIALIZING SPEED DIAL
NUMBERS, VM ID CODES, CHARACTER MESSAGE MEMORY,
TIMED REMINDERS, DIGITAL TELEPHONE VOLUME,
AND CALL FORWARD BACKUP MEMORY .............................................
PROGRAM 03/SLOT ASSIGNMENTS .......................................................
PROGRAM 00/SOFTWARE CHECK AND REMOTE MAINTENANCE
SECURITY CODE ASSIGNMENTS ...........................................................
PROGRAM 04/PORT AND STATION NUMBER ASSIGNMENT ...............
TELEPHONE BUTTON LABELS ................................................................
PAGE
1-3
1-4
1-7
1-9
1-11
1-12
1-14
1-16
FIGURE LIST
FIGURE
1-1
1-2
1-3
1-4
1-5
1-6
1-7
SUBJECT
PROGRAMMING BUTTON SEQUENCE OVERVIEW ...............................
TELEPHONE PROGRAMMING TEMPLATES ...........................................
INITIALIZING DATA FOR PROGRAMS 00 ~ 97 WITH PROGRAM 90 .....
INITIALIZING SPEED DIAL NUMBERS, VM ID CODES, CHARACTER
MESSAGE MEMORY, TIMED REMINDERS, DIGITAL TELEPHONE
VOLUME, AND CALL FORWARD BACKUP MEMORY WITH
PROGRAM 92.............................................................................................
SETTING SYSTEM DATE ..........................................................................
SETTING SYSTEM TIME ...........................................................................
SETTING SYSTEM DAY OF WEEK ...........................................................
i
PAGE
1-2
1-6
1-8
1-10
1-15
1-15
1-15
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
features. The record sheets are organized by program number in most cases.
1 PURPOSE
1.01 The purpose of this programming section is to
provide the system installer with instructions to set
the detailed feature configuration and operation of
the system.
3.10 Programming Data Entry Overview
3.11 Keystrokes for entering data from System
Record Sheets follow a five-step pattern, detailed
in the following description and illustrated in Figure
1-1.
1.02 This chapter provides an overview of the
programming section, its organization, and some
general programming instructions.
NOTE:
Button (key) sequences that stay the same for
every program are abbreviated and shaded
on each record sheet, button sequences that
are unique for every program are white.
2 ORGANIZATION
2.01 This programming section is organized in
modular chapters. The chapters are titled as follows:
1) In Step 1, enter the programming mode by
pressing a series of buttons shown in Figure
1-1. To save space on the record sheets, the
abbreviation “P” denotes this entry sequence.
“P” buttons are always shaded.
2.02 Chapter One—Introduction (Section 100816-301). Begins with an overview of the section’s
purpose and organization. Also included are basic
instructions on how to program the system with a
20-button LCD digital or (in DK16 only) electronic
telephone, some general programming notes, and
a description of system initialization.
NOTE:
The LCD will continue to display idle status
information— station number, date, and time—
until Step 1 is finished.
2.03 Chapter Two—System Record Sheets and
Instructions (Section 100-816-302). Provides a
record sheet for every program (00 ~ 97) and
instructions on how to fill them out. The system
programmer programs the system from data on the
record sheets. Program cross-reference tables in
numerical and alphabetical order are also included.
The same record sheets are used for DK8 and
DK16; program options and data that does not
apply to DK8 are shaded or noted with footnotes.
2) In Step 2, enter the program number. This
sequence is unique for every program. The
buttons are white and never abbreviated.
NOTE:
When the speaker button is pressed at the
beginning of Step 2, there will be a beep tone
and "PROGRAM=__" will appear on the LCD.
3) In Step 3, enter the program data. Again, this
sequence is unique for every program. (See
Paragraph 3.20 for more information.) The
buttons are white and never abbreviated. To
make another entry, repeat Step 3 until ready
to exit the current program.
3 GENERAL PROGRAMMING
INSTRUCTIONS
3.01 Programming data is entered from System
Record Sheets at any 20-button LCD digital or (in
DK16 only) electronic telephone; however only one
Telephone can be in the program mode at a time.
(It can also be entered from an on-site or off-site
ASCII terminal. Both of these programming alternatives require optional hardware. See Remote
Administration & Maintenance Procedures, Section 100-816-600, for details.) System Record
Sheets document a specific system’s data configuration, including attributes of a feature or group of
NOTE:
See Paragraph 3.20 for a description of program data entry methods.
4) In Step 4, exit the current program. This sequence never changes. To save space on the
record sheets, abbreviation “Z” denotes the
1-1
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
another program
more data
1
2
Spkr
3
Hold
Step 1
Step 2
Enter Program Mode Enter Program Number
(see note)
P
S
Spkr
Hold
Step 3
Enter Program Data
H
S
and/or
Spkr
Hold
Spkr
Hold
Step 4
Step 5
Exit Current Program Exit Program Mode
H
Z
Z
(LED buttons)
NOTE:
Do not press intercom when entering the “P” sequence
and/or
FIGURE 1-1
PROGRAMMING BUTTON SEQUENCE OVERVIEW
telephone’s LCD, along with prompts and confirmations. See Table 1-A for step-by-step data entry
instructions for Program 33.
ending sequence. “Z” buttons are shaded.
Upon exiting the current program, repeat Step
2 to enter another program or continue with
Step 5 to exit the programming mode entirely.
3.23 Multidimensional Programs. Once a program number is entered, the first dimension (usually a CO line number, a station logical port number,
or a range of ports) must be specified from the
dialpad. Upon specifying this first dimension, programming button LEDs 01 ~ 20 light in the default
configuration. The status of each LED can be
changed by pressing its associated button. Pressing the button while its LED is lit turns the LED off;
pressing the button while its LED is off turns the
LED on. Program 30 is a multidimensional program; see Table 1-B for step-by-step data entry
instructions for Program 30.
• Range Programming: When programming a
range of station ports (Step 5, Table 1-B), the
station’s programming LEDs indicate whether
the data programmed matches for all items in the
range:
§ LED On: Indicates that all ports in the range
are programmed with the data choice that
lights the particular LED.
5) In Step 5, exit the programming mode by
pressing the same buttons as in Step 4. This
sequence also never changes.
3.12 Each System Record Sheet has an abbreviated button sequence at the top of it like the one
shown in Figure 1-1.
3.20 Programming Data Variations
3.21 There are two ways to enter data in Step 3
(Figure 1-1) of a program: pressing the buttons on
the dialpad and pressing the LED buttons. Many
programs are multidimensional and involve both
types of entry.
3.22 Simple Programs. Simple programs, such
as Program 33, only require data to be specified
through the dialpad. Data entered from the dialpad
displays on the programming digital or electronic
1-2
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
TABLE 1-A
SIMPLE PROGRAM: PROGRAM 33
(STATION HUNTING)
Step
#
1.
Press...
BUTTONS + LED keys
Action description
LCD RESPONSE ...
Use an LCD digital or electronic telephone.
Make sure the programming button strip template is
installed on the programming telephone (see
Paragraph 3.24).
JAN
NO. OF STATION (10 ~ 29)
20 SUN
06:43
*#*#1*2*3
Enter programming mode.
PROGRAM MODE
SPKR 3 3 HOLD
Access Program 33. System beeps after SPKR key
is pressed to indicate program number may be entered.
PROGRAM = 33
SPKR
Prepare the system for a station port selection.
33 SELECT =
0 0 ~ 1 9 (0 0 ~ 0 9 for DK8)
Select the logical port number of the “Hunt From” station.
Up to two digits followed by the # key, or a range of ports
can be entered as specified on the record sheet.
33 SELECT = (00 ~ 19)
HUNT TO =
0 0 ~ 1 9 (0 0 ~ 0 9 for DK8)
Enter the logical port number of the “Hunt To” point, as
recorded on the system record sheet. Press LED key 01
to delete a digit from Hunt To point ports.
33 SELECT = (00 ~ 19)
HUNT TO = (00 ~ 19)
7.
HOLD
Secure data in system programming.
33 SELECT = (00 ~ 19)
DATA PROGRAMMED
8.
SPKR
Prepare system for another selection (go back to
step 5), or exit Program 33 (continue with step 9).
33 SELECT =
9.
# # HOLD
Secure Program 33 data in system memory.
33 SELECT = ##
DATA PROGRAMMED
10.
SPKR
Exit Program 33. Enter another program number or
exit programming mode (go to step 11).
Speaker beeps to indicate it is exiting Program 33.
PROGRAM =
11.
# # HOLD
Exit programming mode.
NO. OF STATION (10 ~ 29)
06:58
JAN 20 SUN
2.
3.
4.
5.
6.
1-3
DATA STORE
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
TABLE 1-B
MULTIDIMENSIONAL PROGRAM: PROGRAM 30
(STATION CLASS OF SERVICE)
Step
#
1.
Press...
BUTTONS + LED keys
Action description
LCD RESPONSE ...
Use an LCD electronic or digital telephone.
NO.OF STATION (10 ~ 29)
20 SUN
06:43
Make sure the programming button strip template is
installed on the programming telephone (see
Paragraph 3.24).
JAN
*#*#1*2*3
PROGRAM MODE
SPKR 3 0 HOLD
Access Program 30. System beeps after SPKR
button is pressed to indicate a program number may
be entered.
PROGRAM = 30
4.
SPKR
Prepare system for a port number selection.
30 SELECT =
5.
0 0 ~ 1 9 (0 0 ~ 0 9 for DK8)
Enter the logical port number where the station being
defined is connected. Use two digits, followed by a #
key. A range of ports can be entered as specified in the
record sheet.
30 SELECT = (00 ~ 19)
6.
LED keys 01 ~ 20
LED keys 01 ~ 20 activate features for each station port
or port range. Make the following selections by turning
the appropriate led key ON or OFF for each item (01 ~
20) for each port, as marked on the system record
sheet:
2.
Enter programming mode.
3.
LED 01 ON: Speakerphone Enabled
LED 02 ON: Microphone Key Lock Enabled
LED 03 ON: Microphone ON at Start of Call
LED 04 ON: Not Used
LED 05 ON: Speed Dial Allowed
LED 06 ON: Automatic Busy Redial Access Enabled
LED 07 ON: OCA/Busy Override Automatic
LED 08 ON: Forced Account Code Enabled
LED 09 ON: Toll Restriction Override Code Revision
Authority
LED 10 ON: DISA Security Code Change Allowed
LED 11 ON: Dial Pulse (DTMF Off) for Standard
Telephone
1-4
DATA STORE
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
TABLE 1-B (continued)
MULTIDIMENSIONAL PROGRAM: PROGRAM 30,
STATION CLASS OF SERVICE
Step
#
6.
Press...
BUTTONS + LED keys
Action description
LCD RESPONSE ...
LED keys 01 ~ 20 (continued)
LEDs 12 and 13 ON: Digital Telephone Handset
Receiver Volume
LED 14 ON: Account Codes Verified
LED 15 ON: Verified Account Code Revision Authority
LED 16 ON: Traveling Class of Service Code Revision
Authority
LED 17 ON: Do Not Disturb Override Allowed
LED 18 ON: Executive Override Allowed
LED 19 ON: Privacy Override Allowed
LED 20 ON: Not Used
If programming a port range, the LED indications are
as follows:
¥ LED-ON, all ports in range are enabled for that item.
¥ LED-OFF, all ports in range are disabled for that item.
¥ LED-FLASHING, some ports in range are enabled and
some ports are disabled.
7.
HOLD
Secure data in system programming.
30 SELECT = (00 ~ 19)
DATA PROGRAMMED
8.
SPKR
Prepare system for another selection (go back to
step 5), or exit Program 30 (continue with step 9).
30 SELECT =
9.
# # HOLD
Secure Program 30 data in system memory.
30 SELECT = ##
DATA PROGRAMMED
10.
SPKR
Exit Program 30. Enter another program number or exit
programming mode (go to step 11).
System beeps to indicate it is exiting Program 30.
PROGRAM =
11.
# # HOLD
Exit programming mode.
NO. OF STATION (10 ~ 29)
JAN 20 SUN
06:58
1-5
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
§ LED Off: Indicates that all ports in the range
• Programming Telephone: The programming
are programmed with the data choice that
does not light the particular LED.
§ LED Flashing: Indicates that data is currently inconsistent for all ports in the range.
Some may be programmed with the LED on,
some with the LED off.
digital or electronic telephone should have 20
flexible feature buttons, an LCD, and a programming template. The Programming telephone can
be connected to any Digital or Electronic station
port.
NOTE:
Electronic telephones are not supported by
the STRATA DK8.
3.24 Telephone Programming Template. Special programming buttonstrip templates (Figure 12) are provided with your system. A template must
be on the programming telephone to properly enter
data from the System Record Sheets. The templates assign numbers to each of the 20 buttons on
the telephone that coincide with tables found in the
record sheets.
3.33 Completing the Record Sheets. Ensure
that the Basic System Record Sheets, Toll Restriction System Record Sheets, and Least Cost Routing System Record Sheets have been completely
filled out. If they have not been, do so before
continuing. The Record Sheets are in Programming Procedures Chapter 2.
3.30 Preparing the System for Programming
3.31 This section explains how to prepare the
system for programming.
3.34 Initializing the System. The system's memory
must be cleared by initializing its data. Initializing
data activates standard, default data assignments
(stored in ROM).
3.32 Minimum Hardware Requirements. A system must have the following minimum hardware
installed for programming, as described in the
installation section, Section 100-816-200:
• Power Supply: The power supply must test
satisfactorily and must be on.
• Battery Strap: The SW1 battery strap on the
Key Service Unit should be in the On position.
3.35 Initialize Programs 00 ~ 97 Data with Program 90: Always initialize a system with Program
90 when it is first installed, or when its software
must be brought to the default configuration. If only
minor programming changes are being added to a
system in which the programming is basically
correct, do not run Program 90. Follow the steps in
Table 1-C and Figure 1-3 to run Program 90.
Programming Keystrip Button Layouts
DKT 2000 and
EKT 6500 Series
10
09
08
07
06
05
04
03
02
01
20
19
18
17
16
15
14
13
12
11
DKT 1000 Series
16
11
06
01
FIGURE 1-2
TELEPHONE PROGRAMMING TEMPLATES
1-6
17
12
07
02
18
13
08
03
19
14
09
04
20
15
10
05
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
TABLE 1-C
PROGRAM 90
INITIALIZING PROGRAMS 00 ~ 97
See Program 90 System Record Sheet
Step
#
1.
Press...
BUTTONS + LED keys
Action description
LCD RESPONSE ...
Use an LCD digital or electronic telephone with a
programming template.
JAN
NO. OF STATION (10 ~ 29)
20 SUN
06:30
2.
*#*#1*2*3
Enter programming mode.
PROGRAM MODE
3.
SPKR 9 0 HOLD
Access Program 90. System beeps after SPKR
button is pressed to indicate the program number
can be entered.
PROGRAM = 90
4.
SPKR
Prepare system for the programs to be initialized.
90 SELECT =
5.
0 0 * 9 7 + LED keys 01 & 02
Enter program numbers individually or in a range.
For a range, separate the low program number and
the high program number with an asterisk.
NOTE:
To initialize only one program, enter the two digit
#), then press
program number followed by a # (
Key 01 & 02.
90 SELECT = 00*97
DATA CLR
6.
HOLD (LEDs 01 and 02 flash rapidly)
Secures data in system programming. LEDs 01
and 02 flash.
90 SELECT = 00*97
DATA PROGRAMMED
7.
SPKR
Prepare system for another selection (go back to
step 5), or exit Program 90 (continue with step 8).
90 SELECT =
8.
# # HOLD
Secure Program 90 data in system memory.
90 SELECT = ##
DATA PROGRAMMED
9.
SPKR
Exit Program 90. Enter another program number or exit
programming mode (go to step 10).
System beeps to indicate it's exiting Program 90.
PROGRAM =
10.
# # HOLD
Exit programming mode.
DATA STORE
JAN
NOTE:
The system will not allow the SPKR
LED to light to reenter the programming mode.
1-7
NO. OF STATION (10 ~ 29)
20 SUN
06:42
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
EXIT programming mode
or
P
S
9
0
H
01
S
H
Z
Z
END Program 90
Program(s) to be initialized
Enter programming mode
02
Button 1 and 2 LEDs must be lit
Initialize Programs 00 ~ 97 every time:
• Installing a new system
• To bring a system's programming back to the default setting.
Specify the range as follows:
0
0
*
9
7
To initialize one program at a time, enter just the individual program number, then #.
FIGURE 1-3
INITIALIZING DATA FOR PROGRAMS 00 ~ 97 WITH PROGRAM 90
1-6, and 1-7 on instructions on how to set the time
and date.
3.36 Initialize Speed Dial Numbers, Voice Mail
Identification Codes, Character Message
Memory, Timed Reminders, Digital Telephone
Volume, and Call Forward Backup Memory with
Program 92. Complete this step if the system is
being installed for the first time, or when all currently
programmed Speed Dial numbers or the like must
be deleted. Follow the steps in Table 1-D and refer
to Figure 1-4.
NOTE:
It is not necessary to run Program 03 for the
STRATA DK8.
4.02 Enter data from the record sheets. For help in
entering program data from the record sheets, see
Tables 1-A and 1-B. The data entry methods used
in these tables reflect the entry methods used for
most of the programs.
4 AFTER INITIALIZATION
5 TELEPHONE BUTTON LABELS
4.01 Immediately after initializing the system, Program 03 must be run to inform the software of the
system hardware configuration (Table 1-E), Program 00 to assign remote maintenance security
codes and to check the system software level
(Table 1-F), and Program 04 to assign station
numbers (Table 1-G). Anytime after initialization,
the time and date can be set. Refer to Figures 1-5,
5.01 This programming section makes references
to specific telephone buttons. Depending on the
telephone, the label designations for these buttons
vary. The labels referred to in this section appear on
the 2000-series Digital Telephones; see Table 1-H
for the labels of other telephone models.
1-8
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
TABLE 1-D
INITIALIZATION PROGRAM 92
INITIALIZING SPEED DIAL NUMBERS, VM ID CODES, CHARACTER MESSAGE MEMORY,
TIMED REMINDERS, DIGITAL TELEPHONE VOLUME, AND CALL FORWARD BACKUP MEMORY
Step
#
Press...
BUTTONS + LED keys
Action description
1.
Use an LCD digital or electronic telephone with programming template.
2.
#*#1*2* 3
Enter programming mode.
SPKR 9 2 HOLD
Access Program 92. System beeps after
SPKR button is pressed to indicate when to
enter program number.
SPKR
Prepare system for selection of programs to initialize.
For new system installation, always perform 5A ~ 5F.
Select one of the following:
1 + LED keys 01 & 03
Clears station speed dial, voice mail ID codes, and LCD
memos assigned to station speed dial numbers.
OR
2 + LED keys 01 & 04
Clears system speed dial and LCD memos assigned to system speed
dial numbers.
OR
3 + LED keys 02 & 03
Clears character message memory (station and system) and user
name display.
OR
4 + LED keys 02 & 04
Clears timed reminders.
OR
5 + LED keys 01 & 05
Presets the Ring/Speaker, Mute Ring, and Intercom Tone/BGM,
volume levels of all digital telephones to approximately midrange.
OR
9 + LED keys 03 & 04
Clears Call Forward Memory except Fixed Call Forward Memory.
HOLD (LEDs turn off)
Secure data in system programming. Repeat steps 4 ~
6 until steps 5A ~ 5F are completed (see note).
SPKR
Prepare system for another selection (go back to step
5), or exit Program 92 (continue with step 8).
# # HOLD
Secure Program 92 data in system memory.
SPKR
Exit Program 92. Enter another program number, or exit programming
mode (go to step 10). System beeps to indicate it's exiting Program 92.
# # HOLD
Exit programming mode.
*
3.
4.
5. A.
B.
C.
D.
E.
F.
6.
7.
8.
9.
10.
LCD RESPONSE ...
NO. OF STATION (10 ~ 29)
JAN 20 SUN
06:43
PROGRAM MODE
PROGRAM = 92
DATA STORE
92 SELECT =
92 SELECT = 1
EACH DIAL CLR
92 SELECT = 2
COMMON DIAL CLR
92 SELECT = 3
MSG CLR
92 SELECT = 4
TMR REMINDER CLR
92 SELECT = 5
DKT VR INITIAL
92 SELECT = 9
BACK UP RAM CLR
92 SELECT = (1~0)
DATA PROGRAMMED
92 SELECT =
92 SELECT = ##
DATA PROGRAMMED
PROGRAM =
JAN
NO. OF STATION (10 ~ 29)
20 SUN
06:58
NOTE:
If the call forward memory was cleared, cycle system power after Step 6, if it is required to reset telephone call
forward LCD displays or call forward button LED indications.
1-9
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
more data
P
S
Enter programming mode
9
2
H
S
H
SELECT = (as below)
Specify if initializing Station Speed Dial,
System Speed Dial,Character Message
Memory, Timed Reminders, or Digital
Telephone Volume Levels:
Z
Z
END Program 92
EXIT programming mode
1
01
03
Clears Station Speed Dial, Voice Mail ID Codes,
and LCD memos Assigned to Station Speed Dial numbers.
2
01
04
Clears System Speed Dial and LCD memos assigned to
System Speed Dial numbers.
3
02
03
Clears LCD Character Message Memory (Station and System).
4
02
04
Clears Timed Reminders.
5
01
05
Initialize Digital Telephone Ring/Speaker, Mute Ring,
and Intercom Tone/BGM volume levels.
9
03
04
H
Power OFF 5
seconds; then
Power ON
Clears Call Forward Memory and resets
call forward indications on telephones.
FIGURE 1-4
INITIALIZING SPEED DIAL NUMBERS, VM ID CODES, CHARACTER MESSAGE MEMORY, TIMED
REMINDERS, DIGITAL TELEPHONE VOLUME, AND CALL FORWARD BACKUP MEMORY WITH
PROGRAM 92
1-10
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
Step
#
1.
Press...
BUTTONS + LED keys
Action description
TABLE 1-E
PROGRAM 03
SLOT ASSIGNMENTS
(DK16 ONLY)
LCD RESPONSE ...
Use an LCD digital or electronic telephone with a
programming template.
JAN
NO. OF STATION (10 ~ 29)
20 SUN
06:43
2.
*#*#1*2*3
Enter programming mode.
PROGRAM MODE
3.
SPKR 0 3 HOLD
Access Program 03. After SPKR key is pressed, system
beeps to indicate program number may be entered.
PROGRAM = 03
4.
SPKR
Prepare system for a selection.
03 SELECT =
5.
Enter a PCB slot number (00~07).
03 SELECT = (00 ~ 07)
CARD = Default code will
appear here
03 SELECT = 00
SLOT NUMBER
CARD = 91
The system defaults as follows:
00
Initialized data assigns CTU slot 00 to be non-optioned,
without a K4RCU.
01
Initialized data assigns DKU slot 01 to be non-optioned
without a door phone or DDSS console.
02
Initialized data assigns fixed KCOU slot 02 with code 11.
03
Initialized data assigns fixed KSTU slot 03 with code 31.
04 ~ 07
Initialized data assigns Expansion Unit’s universal slots
04 ~ 07 to be empty, code 00.
DATA STORE
03 SELECT = 01
SLOT NUMBER
CARD = 61
03 SELECT = 02
SLOT NUMBER
CARD = 11
03 SELECT = 03
SLOT NUMBER
CARD = 31
03 SELECT = 04 ~ 07
SLOT NUMBER
CARD = 00
6.
0 0 ~9 2
Dial the PCB code recorded on the record sheet.
Refer to the PCB code reference table on Program 03
System Record Sheet for a definition of the codes.
03 SELECT = (00 ~ 07)
CARD = (00 ~ 92)
7.
HOLD
Secure data in system programming.
03 SELECT = (00 ~ 07)
DATA PROGRAMMED
8.
SPKR
Prepare system for another selection (go back to
step 5), or exit Program 03 (continue with step 9).
03 SELECT =
9.
# # HOLD
Secure Program 03 data in system memory.
03 SELECT = ##
DATA PROGRAMMED
10.
SPKR
Exit Program 03. Enter another program number, or exit
programming mode (go to step 11).
System beeps to indicate it's exiting Program 03.
PROGRAM =
11.
# # HOLD
Exit programming mode.
NO. OF STATION (10 ~ 29)
06:58
JAN 20 SUN
12.
In order to secure Program 03 entries, POWER OFF
for 5 seconds, then POWER ON.
1-11
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
TABLE 1-F
PROGRAM 00
SOFTWARE CHECK AND REMOTE MAINTENANCE SECURITY CODE ASSIGNMENTS
Press...
BUTTONS + LED keys
Action description
LCD RESPONSE ...
Use an LCD digital or electronic telephone
with a programming template.
JAN
2.
*#*#1*2*3
Enter programming mode.
PROGRAM MODE
3.
SPKR 0 0 HOLD
Speaker beeps to indicate when to enter program
number. Access Program 00.
PROGRAM = 00
4.
SPKR
Prepare system for a selection.
00 SELECT =
5.
Select one of the following attributes:
Step
#
1.
NO. OF STATION (10 ~ 29)
20 SUN
06:43
DATA STORE
A. 0
View the software version. This attribute is not editable.
OR
00 SELECT = 0
. (DK8 ONLY)
VERSION = QMA
--OR-VERSION = PSSA . (DK16 ONLY)
. = SOFTWARE VERSION ID
B. 1
Define the Level 1 remote maintenance security code
from the System Record Sheet (four digits max.). Level 1
allows remote access to all programs and data.
Default Level 1 security code is "0000."
OR
C. 2
Define the Level 2 remote maintenance security code
from the System Record Sheet (four digits max.). Level 2
allows remote entry to Programs 30 ~ 39 and 77 ~ 89
only. Default Level 2 security code is "0000."
OR
D. 8
View the software RAM Checksum. This attribute is not
editable. The default checksum may change.
OR
E. 9
View the Power Supply Cycle Counter. This attribute is
not editable. The counter indicates the number of times
power is removed from the system after Program 00
was initialized via Program 90.
00 SELECT = 1
PASSWORD = 0000
00 SELECT = 2
PASSWORD = 0000
00 SELECT = 8
SUM = XXXXXXXXX
00 SELECT = 9
COUNTER = XXXX
6.
HOLD
Secure data in system programming.
(Only works for “1” and “2”)
00 SELECT = (0,1,2,8, or 9)
DATA PROGRAMMED
7.
SPKR
Prepare system for another selection (go back to
step 5), or exit Program 00 (continue with step 8).
00 SELECT =
1-12
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
TABLE 1-F (Continued)
PROGRAM 00
SOFTWARE CHECK AND REMOTE MAINTENANCE SECURITY CODE ASSIGNMENTS
Step
#
8.
9.
10.
Press...
BUTTONS + LED keys
Action description
LCD RESPONSE ...
# # HOLD
Secure Program 00 data in system memory.
00 SELECT = ##
DATA PROGRAMMED
SPKR
Exit Program 00. Enter another program number or exit
programming mode (go to step 10).
System beeps to indicate it's exiting Program 00.
PROGRAM =
# # HOLD
Exit programming mode.
NO. OF STATION (10 ~ 29)
06:58
JAN 20 SUN
1-13
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
TABLE 1-G
PROGRAM 04
PORT AND STATION NUMBER ASSIGNMENT
Step
#
Press...
BUTTONS + LED keys
Action description
LCD RESPONSE ...
1. Use an LCD digital or electronic telephone with a
programming template.
2.
*#*#1*2*3
JAN
NO. OF STATION (10 ~ 29)
20 SUN
06:43
PROGRAM MODE
Enter programming mode.
3. SPKR 0 4 HOLD
Access Program 04. System beeps after SPKR
is pressed to indicate a program number may be entered.
PROGRAM = 04
4. SPKR
Prepare system for a selection.
04 SELECT =
DATA STORE
5. 0 0 # ~ 1 9 #
04 SELECT = 00
Select the number of the logical port (use two digits), then #. INT = 10
Initialized data assigns station numbers 10 ~ 19 DK8 or
10 ~ 29 DK16.
6.
04 SELECT = 00 ~ 19
INT = XXXX
Enter the port's station number from the record
sheet (four digits max.).
NOTE:
Station numbers must not exceed four digits, or
conflict with feature access codes listed in Program
05 System Record Sheet.
7. HOLD
Secure data in system programming.
04 SELECT = (00 ~ 19)
DATA PROGRAMMED
8. SPKR
Prepare system for another port selection (go back
to step 5), or exit Program 04 (continue with step 8).
04 SELECT =
9. # # HOLD
Secure Program 04 data in system memory.
04 SELECT = ##
DATA PROGRAMMED
10. SPKR
Exit Program 04. Enter another program number,
or exit programming mode (go to step 10).
System beeps to indicate it's exiting Program 04.
PROGRAM =
11. # # HOLD
Exit programming mode.
NO. OF STATION (10 ~ 29)
06:58
JAN 20 SUN
1-14
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
HOW TO SET THE DATE
The date can be set from an LCD electronic or digital telephone connected to a logical port 00.
Press the following button sequence with the handset on-hook:
Intercom
6
5
1
Redial
Date in year/month/day
format (YYMMDD). If month
or day is a single digit, precede
with a zero (0).
Electronic telephones can use
the # button if lhe do not have
the Redial (RDL) button.
FIGURE 1-5
SETTING SYSTEM DATE
HOW TO SET THE TIME
The time can be set from an LCD electronic or digital telephone connected to a logical port 00.
Press the following button sequence with the handset on-hook:
Intercom
6
5
2
Redial
Time in hours/minutes/seconds
format (HHMMSS from 000000
to 235959). If any of these values
is a single digit, precede with a
zero (0).
Electronic telephones can use
the # button if lhe do not have
the Redial (RDL) button.
FIGURE 1-6
SETTING SYSTEM TIME
HOW TO SET THE DAY
The day can be set from an LCD electronic or digital telephone connected to a logical port 00.
Press the following button sequence with the handset on-hook:
Intercom
6
Enter the digit for today's day:
1 = Sunday
2 = Monday
3 = Tuesday
4 = Wednesday
5 = Thursday
6 = Friday
7 = Saturday
FIGURE 1-7
SETTING SYSTEM DAY OF WEEK
1-15
5
3
Redial
Electronic telephones can use
the # button if lhe do not have
the Redial (RDL) button.
PROGRAMMING PROCEDURES-INTRODUCTION
SECTION 100-816-301
MARCH 1993
TABLE 1-H
TELEPHONE BUTTON LABELS
2000-series Digital
Telephone Button Label
Designation on other
Telephone models
2000-series Digital
Telephone Button Labels
(cont)
Designation on other
Telephone Models
(cont)
Account Code
ACCNT
Mic
MIC
Alarm Reset
ALRM
Microphn Cut-off
MCO
All Call Page
AC
Modem
MODEM
Auto Busy Redial
ABR
Msg
MESSAGE
Auto Callback
ACB
Night Transfer
NT
Call Frwd All Calls
CFAC
Night Transfer1
NT1
Call Frwd Busy
CFB
Night Transfer2
NT2
Call Frwd Busy NAns
CFB/NA
Pooled Line Grp
PL
Call Frwd No Answer
CFNA
Privacy on Line
PRIVACY
Call Frwd to:____
CFF
Privacy Release
PRV RLS
Cnf/Trn
CONF/TRNS
Redial
REDIAL or RDL
Data Call
DATA
Release Call
RLS
Data Release
DRLS
Save Last Number
SAVE
Directed Pickup
PKUP
SD
SD
Directed Pickup1
PKUP1
Spd Dial Lng Pause
PAU/L
Directed Pickup2
PKUP2
Spd Dial Pause
PAU
Do Not Disturb
DND
Speed Dial
SDS
DSS
DSS
Spkr
SPEAKER or SPKR
Flash
FLASH or MW/FL
Tel Set Music
BGM
Hold
HOLD
Tone Dial Select
TONE
Intercom
INT
Unlock Door
DRLK
LCD Msg Select
MSG
Vol
VOLUME
1-16
TOSHIBA SYSTEM PRACTICES
DIGITAL KEY TELEPHONE SYSTEMS
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAMMING PROCEDURES
CHAPTER TWO
INSTRUCTIONS/RECORD SHEETS
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
TABLE OF CONTENTS
PARAGRAPH
1
1.10
1.20
1.30
2
3
3.00
3.10
4
4.10
4.20
4.30
4.40
4.50
4.60
4.70
4.80
4.90
4.100
5
6
6.00
6.10
6.20
7
7.10
7.20
7.30
7.40
SUBJECT
GENERAL ...................................................................................................
Record Sheet Data Entry ........................................................................
Logical Ports and Physical Ports ............................................................
Basic System Record Instructions ..........................................................
TOLL RESTRICTION ..................................................................................
TOLL RESTRICTION OVERVIEW .............................................................
Toll Restriction Methods .........................................................................
Toll Restriction Features .........................................................................
COMPLETING THE TOLL RESTRICTION SYSTEM RECORD ................
Program 44B—Toll Restriction/Traveling Class Override Codes ...........
Program 45-1—Toll Restriction Dial Plan ...............................................
Program 45-2—Toll Restriction Disable .................................................
Program 45-3 ~ 6—Equal Access/Special Common Carrier Numbers
and Authorization Code Digit Length ......................................................
Program 45-8 ~ 9—Toll Restriction Override Code ................................
Program 46-2 ~ 4—Toll Restriction Allowed/Denied Area Codes
Assigned by Class ..................................................................................
Program 46-6 ~ 8—Toll Restriction Allowed/Denied Office Codes
Assigned by Class ..................................................................................
Program 46-10 ~ 40—Toll Restriction Class Parameters
(Classes 1 ~ 4) .......................................................................................
Program 47—Toll Restriction Exception Office Codes Assigned by
Area Codes (Table 1 ~ 8) .......................................................................
Program 48—Station Toll Restriction Classification ...............................
LEAST COST ROUTING ............................................................................
LEAST COST ROUTING OVERVIEW ........................................................
Definition .................................................................................................
LCR Schedule Assignments ...................................................................
Conditions ...............................................................................................
COMPLETING THE LEAST COST ROUTING SYSTEM RECORD ...........
LCR CO Line Programming Reference Chart ........................................
Program 50 Series—LCR Definitions .....................................................
Route Plan Overview ..............................................................................
Program 55 Series—LCR Modified Digits Tables ..................................
PAGE
2-1
2-1
2-1
2-1
2-22
2-22
2-22
2-22
2-23
2-23
2-23
2-25
2-25
2-25
2-26
2-26
2-26
2-27
2-27
2-28
2-28
2-28
2-28
2-30
2-30
2-30
2-31
2-32
2-34
FIGURE LIST
FIGURE
2-1
SUBJECT
LCR OPERATIONAL BLOCK DIAGRAM ...................................................
i
PAGE
2-29
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
tering ports into program data, except for Program
01, always enter the logical port number.
1 GENERAL
1.01 This chapter consists of System Record
Sheets and instructions on how to fill out each of
them. The chapter begins with the instructions:
first the basic program instructions, then the Toll
Restriction instructions, and then the Least Cost
Routing instructions. The remainder of the chapter
contains the System Record Sheets, organized in
the same sequence as the instructions.
1.30 Basic System Record Instructions
Program 90—Initializing Programs: All customer
data can be cleared and set to the initialized
state for any program or range of programs. If
the system is being installed for the first time or
if installing a KFCU in a STRATA DK16 (if
instructions specify), this program must be run
to erase random data from RAM. Initialized data
information can be found at the bottom of each
program System Record Sheet. If the system is
being installed for the first time or in a new
location or when installing a KFCU in a STRATA
DK16 (if instructions specify), all programs (00 ~
97) should be initialized.
Program 92—Initializing Speed Dial Numbers,
Voice Mail ID Codes, Character Message
Memory, Timed Reminders, Call Forward,
and Digital Telephone Volume Levels: All
previously entered or random data (of the type
listed) is cleared by this program. This program
must be run when installing a system for the first
time or in a new location or when installing a
KFCU in a STRATA DK16 (if instructions specify).
1.10 Record Sheet Data Entry
1.11 The System Record Sheets are used to
record the assignment of features or operation of
each program. The following descriptions and
considerations of the available programming
choices will be helpful when filling out the record
sheets.
1.12 Initialized data information can be found in
the Notes at the bottom of each System Record
Sheet.
1.20 Logical Ports and Physical Ports
1.21 There are two types of ports in the STRATA
DK8/DK16 systems. This distinction gives customers greater mobility in relocating their stations.
Physical ports can be defined as the actual hardware—printed circuit board (PCB) circuit, wiring,
and jack (RJ11) that stations plug into—that is
connected to the system. Logical ports are attributes associated with a station (telephone)—
station number, personal Speed Dial numbers,
and the complement of features assigned to the
station in system software programs. A Logical
port always is associated with a physical port.
NOTE:
Program 03 applies to STRATA DK16 only.
Program 03—DK16 Flexible PCB Slot Assignments: This program is used to tell the system’s
software how the system is configured. The
configuration is based on slots, and the system
must know what is in each slot. Enter a new code
or verify the default code for each slot. (See the
PCB Code Reference Table on the Program 03
System Record Sheet.) This Program must be
run if the system is being installed for the first
time, or when adding a new PCB, or when
installing a KFCU (if instructions specify).
For this program’s purpose, the Base Key
Service Unit is divided into four fixed slots, even
though the unit has no slots per se. Slot 00
represents the system’s common control (CTU);
Slot 01 the Base Unit’s eight digital circuits/ports
(DKU); Slot 02 the Base Unit’s four CO line
circuits (KCOU); and Slot 03 the optional KSTU
PCB in the Base Unit.
The optional Expansion Unit has four slots
(04 ~ 07). Unlike the Base Unit, the Expansion
Unit’s slots are universal. This means that each
1.22 Physical ports can be considered as fixed;
they cannot be moved. Logical ports, though, are
not fixed. They can be moved from one physical
port to another physical port. It is important to note
that logical ports can only be moved to related
physical ports: Digital logical port (telephone) to
digital physical port (QCDU and KSU digital circuits for STRATA DK8; PDKU, KCDU, and the
Base Unit digital circuits for STRATA DK16), electronic logical port (telephone) to electronic physical port (PEKU and PESU for STRATA DK16), and
standard logical port (standard telephone) to standard physical port (QSTU for STRATA DK8; PSTU,
PESU, and KSTU for STRATA DK16). When en-
2-1
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
signed to logical ports with Program 04. Station
number assignment is fully flexible so that each
station can have any intercom number assigned
up to four digits. However, if the first digit is not
1 or 2, access code conflicts may exist, and
a new system numbering plan will have to be
carefully worked out—If desired, a digital telephone accompanying a DDSS console (STRATA
DK16 only) or Add-on module (DK8 and DK16)
can have a station number of 0 or 01, etc.
without conflict.
All user guides are written using the standard access codes and station numbers. If no
assignment is made in Program 04, the system
when powered up will automatically assign station numbers as follows:
• For STRATA DK8: The system automatically assigns station numbers 10 ~ 13 to the
digital telephone circuit ports in the KSU,
station numbers 14 ~ 15 to the first optional
CO Line/Digital Telephone Interface Unit
(QCDU) PCB (even if it is not installed),
station numbers 16 ~ 17 to the second
optional (QCDU) PCB (even if it is not installed), and station numbers 18 ~ 19 to the
optional Standard Telephone Interface Unit
(QSTU) PCB (even if it is not installed).
• For STRATA DK16: The system automatically assigns station numbers 10 ~ 17 to the
digital telephone circuit ports in the Base
Unit, station numbers 18 ~ 21 to the optional
Base Unit Standard Telephone Interface
Unit (KSTU) PCB (even if it is not installed),
and station numbers 22 ~ 29 to the optional
Expansion Unit (even if it is not installed).
Program 04 does not apply to the door phone
standard numbering scheme (551 ~ 556 for
STRATA DK8 and DK16), the internal modem
(IMDU) number (619) (for STRATA DK16 only),
or the Direct Inward System Access (DISA)
class of service port (Port 10 for STRATA DK8,
Port 20 for STRATA DK16). The system automatically assigns door phone station numbers if
a door phone is specified in Program 77-1.
Programs 01 & 02—Logical and Physical Station Port Display: Logical and physical ports
can both be displayed with Program 01 or 02.
Logical ports cannot be relocated with either of
these two programs.
of these slots is capable of supporting any of
the following PCBs: PDKU, PEKU, PSTU,
PESU, PIOU, PIOUS, KCDU. It is important to
note that Slots 04 and 05 are 16 channel slots
that are capable of supporting Off-hook Call
Announce (OCA) and Data Interface Units
(DIUs), whereas Slots 06 and 07 are eight
channel slots that cannot support OCA or DIUs.
Therefore, we recommend that you install the
station PCB in either Slot 04 or 05 rather than 06
or 07. The Expansion Unit can support a maximum of eight station ports and four CO lines.
IMPORTANT NOTE!
After completing Program 03, turn the
system power off for five seconds and
then turn it back on. This will set in memory
all of the configuration data entered in this
program.
Program 00—Software Check/Remote Maintenance Security Code Assignments: The RAM
checksum, the KPSU Power Cycle Counter,
and the system software version can be verified
with this program. Neither of these attributes
can be changed or edited with this program.
Program 00, though, does allow two security
codes to be set for Remote Maintenance:
• Level 1 Security Code—Remote Maintenance security code which allows entry to all
programs and data.
• Level 2 Security Code—Remote Maintenance security code which allows entry to
Programs 30 ~ 39 and 77 ~ 89.
Program 04—Logical Port/Intercom Number
Assignment: Initialized station intercom numbers are 10 ~ 19 (STRATA DK8) or 10 ~ 29
(STRATA DK16), which are assigned to logical
ports 00 ~ 09 (STRATA DK8) or 00 ~ 19 (STRATA
DK16), respectively. This program can be used
to change this initialized setting.
The standard station intercom numbers 10
~ 19 (STRATA DK8), 10 ~ 29 (STRATA DK16)
can be reassigned to different logical port
numbers with Program 04; or the station intercom numbers can first be changed to numbers
other than 10 ~ 19 (STRATA DK8), 10 ~ 29
(STRATA DK16) with Program 05, then as-
2-2
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
• The logical port associated with a physical
• Automatic Busy Redial (ABR) Cycles,
port can be verified with Program 01. After
entering the physical port, the associated
logical port will appear on the LCD.
• The physical port associated with a logical
port can be verified with Program 02. After
entering the logical port, the associated
physical port will appear on the LCD. See
Program 04's System Record Sheet for
port relocation considerations.
Program 05—Flexible Access Code Numbering: The first digit of a feature access code may
be changed to a different digit or to two digits.
Digits after this prefix cannot be changed. Standard access codes are shown as reference in
the Program 05 System Record Sheet. Some
do not change (such as Automatic Callback)
and are shown with "N/A" for not affected. Access code conflicts may exist if new access
codes are assigned; and a new system numbering plan will have to be carefully worked out.
Pay particular attention to the internal modem
(619) (for STRATA DK16 only) and door phones
551 ~ 556. Station number assignments may
have to be changed using Program 04.
Program 10-1—System Assignments 1: The
following options are available on a systemwide basis.
• Two CO Conference, LED 20—Two CO
lines can be conferenced with one or two
telephones (any type). Conference (LED
19) in this program must be enabled for this
feature to work. Also, two CO line conference must be allowed for Direct Inward
System Access use of outgoing lines.
• Conference, LED 19—The ability of stations to perform any conference can be
allowed or disallowed system-wide.
• Ring Detect Time, LED 18—This should be
set to normal unless connected to Central
Office/CENTREX lines that send ring signals less than 120 milliseconds.
• Intercom Volume PAD, LED 17—LED 17
ON reduces station to station intercom volume. LED 17 should be OFF in all cases
except where extreme quiet room noise is
expected.
• CO Line Dial Pulse Rate, LED 14—(DK8
only) CO line dial pulse rate can be selected
10 PPS or 20 PPS (See Program 15 for
DK16).
LED 12—If activated from a digital or electronic telephone, ABR will retry dialing a
telephone number on a CO line if a far end
busy signal is detected. The choice is given
of retrying 10 or 15 times before terminating.
This feature is not available with standard
telephones.
ABR Redial Time, LED 11—Upon detection of a far end busy signal on a CO line,
ABR will retry either once every 30 seconds
or once every minute.
System Speed Dial Override, Toll Restriction, LED 10—System Speed Dial (*60
~ *99) numbers can be set to override Toll
Restriction.
Exclusive Hold, LED 09—Exclusive Hold
allows electronic and digital telephones to
place calls on hold (by pressing the Hold
button twice) so that other stations cannot
pick up the held call with a CO line button.
This feature can be disabled on a systemwide basis. Any station can pick up an
exclusive hold call by using the call pickup
code.
Alternate Point Answer/Transfer Privacy,
LED 08—If Transfer Privacy is selected, a
transferred call can only be answered at the
called station upon transfer of that call. With
Alternate Point Answer, any electronic or
digital telephone with the appropriate CO
line button can pick up a call transferred to
another telephone. In either case, call pickup
will function from any station.
Ring Transfer, LED 07—This option defines station operation for transferring CO
line calls. If Ring Transfer is allowed, the
system will allow “blind” transfers to busy or
idle stations—the transferring station may
release a transferred call before the called
party answers. If not allowed, the system will
allow supervised transfers only–the called
station must answer before the transferring
station releases. If Ring Transfer is not allowed, immediate recall occurs if “blind”
transfer is attempted. Ring Transfer is not
allowed to stations in the Do Not Disturb
mode; immediate recall will occur if it is
attempted.
CO Repeat Ringing, LED 06—If selected,
the incoming ringing timing pattern at a
station will be the same as the CO line
ringing pattern. This is used mainly with
•
•
•
•
•
•
2-3
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
•
•
•
•
•
LED sets the signaling method for station
intercom calls to digital and electronic telephones. With Voice First, an intercom call to
an electronic or digital telephone will be
preceded by a one second tone burst, followed by voice communication via the
Handsfree Answerback function. For Tone
First, repetitive intercom ring tone is sent in
a one-second on, three-seconds off pattern.
Conversion from one form to the other can
be made by dialing an additional digit of 1
from the calling station.
Program 10-2—System Assignments 2: The
following options are available on a systemwide basis.
• Stations Use External Amplified Conference, LED 19—This feature should only be
used (LED 19 ON) if an external amplifier(s)
(Program 10-3) is used for two CO linestation conference calls. This will provide
additional amplification to the station during
the conference call. If an external amplifier is
not switched into two CO line conference
calls in all cases, LED 19 must be OFF if
there is line unbalance which may cause
hum noise on the station talk path during two
CO line conference calls. For DK8 and DK16,
it is recommended to test two CO line conference with LED 19 ON; if there is no hum
noise, keep LED 19 ON.
• Two CO Line Conference, LED 18—LED
18 should be ON whenever two CO line
(Tandem, DISA) connection is allowed in
Program 15-5 and Program 10-1, LEDs 19
and 20. This will increase the volume level
between the two outside parties on a Tandem (two CO line) connection; but, it will not
affect the station volume of any station
conferenced into the Tandem connection.
This option is not associated with external
amplified conference (Program 10-3).
• "TRNS" Soft Key Immediate Transfer,
LED 17—If this feature is activated and a
transfer is initiated with the "TRNS" Soft Key
on a digital telephone, the call will Ring
Transfer (Camp-on) immediately after the
last digit of the called (busy or idle) station
number is dialed. This feature does not
apply to transfers initiated with the Cnf/Trn
button or the "CONF" Soft Key.
CENTREX or PBX systems which may vary
the ring pattern to distinguish between intercom and incoming calls, etc. If Standard
Ringing is chosen, CO line station ringing
will be a 1 second on, 3 seconds off cycle
regardless of the incoming ring pattern. Some
Central Offices have ringing characteristics
which makes this option undesirable.
Incoming Call Abandon Timing, LED 05—
The amount of time between incoming CO
line ring signals determines when the system will discontinue (abandon) sending ringing tones to stations. The choice of six or
eight seconds is dependent on the CO ring
pattern. This assignment has no effect if
the CO Repeat Ringing (LED 06) option is
used.
Dual-tone Multi-frequency (DTMF) Signal Time, LED 04—DTMF signals sent out
to CO lines can be either 80 or 160 milliseconds in length. DTMF to QSTU/KSTU/PSTU/
PESU ports (including Voice Mail ports) are
not affected by this assignment. See Program 10-2 for QSTU/KSTU/PSTU/PESU
DTMF timing. This program also sets the
minimum duration of DTMF tones sent by
pressing a digit on the dialpad of a 2000series Digital Telephone—It does not, however, affect the maximum duration; DTMF
tones sent by 2000-series Digital Telephones
last as long as a dialpad button is pressed.
Dial Pulse (DP) Make Ratio, LED 03—Dial
Pulse timing sent out to CO lines can be
changed from the normal 40% make ratio to
33%. This selection only applies to those
CO lines assigned in Program 15 to signal
dialing with DP instead of Dual-tone Multifrequency (DTMF).
CO Line Reseize Guard Time, LED 02—
This LED should be set for 0.45 seconds for
most installations. Set guard time for 1.5
seconds (using Program 10-1, LED 02 ON,
and Program 42-0) if CO lines experience
the following situations: no dial tone when a
line is released and reseized immediately;
or, when operating behind CENTREX or
PBX, false hookflash signals are sent to the
Central Office when stations release and
reseize the same CO line immediately.
Tone First/Voice First Signaling-Digital
and Electronic Telephone, LED 01—This
2-4
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
• Executive Override Warning Tone, LED
•
•
•
•
•
•
16—Executive Override allows a station (if
assigned in Program 30) to break into and
overhear an existing station conversation. A
warning tone can be set optionally to be
heard by the conversing parties.
External Page Included with All Call Page,
LED 15—If the all call voice page access
code (39) is dialed, external page (all zones)
may be included or omitted with this LED
option. This option does not affect the All
Call Page button function, which activates
digital and electronic telephone speakers
only, never external page.
Privacy Override Warning Tone, LED 14—
Privacy Override allows a station to enter
into, and overhear, an existing CO line conversation by pressing a CO line button (if the
called station is assigned in Program 30). A
warning tone can be set optionally to be
heard by the conversing parties.
Auto Callback Camp-on Tone, LED 13—
A busy called digital or electronic telephone
user may hear an optional one-time beep
tone (from the speaker) signifying that another station has tried to call and has activated the Automatic Callback (ACB) feature.
CO Line Beep Tone, LED 12—If this LED
is lit, a beep tone will be sent every three
minutes to stations on outgoing CO line
calls.
Dual-tone Multi-frequency (DTMF) Tone
Return, LED 11—This option can delete
DTMF tones that are returned to digital or
electronic telephones when manually dialing or speed dialing. It also eliminates auto
dial digits returned to callers when digits are
automatically sent to voice mail ports on
forwarded calls.
Background Music (BGM)/Music-on-Hold
(MOH) Alternate, LEDs 10 and 9 —An
alternate BGM source can be sent to digital
telephone speakers, electronic telephone
speakers, and external page speakers, while
another music source can be sent to outside
lines or internal stations on hold (MOH). The
BGM source can be connected to a PEKU
(Circuit 3), PESU (Circuit 8), PSTU or KSTU
(Circuit 4) or QSTU (Circuit 2, Port 19). See
•
•
•
•
•
2-5
Program 19 for BGM slot assignments for
DK16. The MOH source can be connected
to the MOH RCA jack on the DK8 KSU or on
the DK16 Base Unit.
Display Dialed Number Timing, LED 08—
An LCD telephone will display a dialed number for either 15 or 60 seconds before the
display changes back to the normal time and
date format.
Standard Telephone Distinctive Ring,
LED 07—The outside-call ring pattern to
standard telephones can be made distinct
from the intercom ring pattern. If Distinctive
Ring is enabled, the CO-line call ring pattern
will be 0.2-seconds on, 0.4-seconds off, 0.2seconds on, 3.4-seconds off; if Distinctive
Ring is not enabled, the pattern will be per
Program 10-1, LED 06. Intercom calls, with
or without Distinctive Ring enabled, ring 1second on and 3-seconds off.
Voice Mail (VM) Identification Code, Dualtone Multi-frequency (DTMF) Signal Time,
LED 06—DTMF digits that are automatically sent to QSTU/KSTU/PSTU/PESU VM
ports can be sent in either 80- or 160millisecond bursts. This applies to digits
sent via voice mail identification code 656/
657 set at each station. This program also
sets the minimum duration of DTMF tones
sent by pressing a digit on the dialpad of a
2000-series digital telephone—It does not,
however, affect the maximum duration;
DTMF tones sent by 2000-series digital telephones last as long as a dialpad button is
pressed.
DISA Busy Tone Cadence, LED 05—Select the busy tone cadence for DISA lines
with this LED. Light the LED for a 0.5 second
cadence (Bell Precise Busy Tone Cadence);
leave it OFF for the STRATA 0.25 second
busy tone cadence. The Bell Precise Busy
Tone cadence should be selected so callers
will know that they have reached a busy
station when calling in on a DISA line. If it is
not selected, the busy tone may be confused with the reorder tone cadence.
Voice Mail (VM) Message Waiting Cancel
Via Dial 6 4/Automatic, LED 04—"Dial 6
4" should be enabled if the DK system is
connected to a VM system that sets station
Message Waiting (MW) LEDs by dialing 6 3
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
dant stations can ring with different signaling modes.
Program 10-3 System Assignments 3: The following options are available on a system-wide
basis.
• LCD BLF Display, LED 20—Turn LED 20
for LCDs to display port numbers when the
Busy Lamp Field (BLF) is activated. LED 20
must be off for LCDs to display default
station numbers when the BLF is activated.
• Speed Dial Entry Timeout, LED 19—Station users can either have up to one minute
or up to three minutes to store Speed Dial
numbers or memos, depending on the LED
17 setting. If they fail to store the Speed Dial
number or memo within the set time, their
station will automatically exit the Speed Dial
Storage mode and change to the normal idle
state. The three-minute setting is recommended if station users will frequently be
storing memos with Speed Dial numbers.
• QSMU TTY/SMDR Option Select, LED 04
(for STRATA DK8 only)—Selects the function of the QSMU PCB: LED 04 ON—TTY,
LED 04 OFF—SMDR.
• External Amplified Conference, LED 02
(for STRATA DK16 only)—Turn LED 02 on
to indicate that an external customer-supplied two-way amplifier is connected to Ports
17 and 18. (These ports must be either
PEKU or PESU electronic telephone ports/
circuits.) The amplifier will amplify two CO
line conference calls. Only one call can be
amplified at a time. Conference calls made
while the amplifier is in use will not be
amplified—See Program 10-1 (LEDs 19
and 20), Program 10-2 (LEDs 18 and 19),
and Program 15-5 for more information
regarding two-CO line conference.
+ station number. This insures that the message LED remains flashing until all VM
messages have been retrieved, at which
time the VM machine should cancel the MW
LED by dialing 6 4 + station number. With
Dial 6 4 enabled, MW indications set on a
station from VM ports will not automatically
be cancelled by the DK system when the
station calls VM to retrieve messages. If
"Automatic" is selected, the flashing message waiting LED is canceled any time a
station calls the VM machine and the VM
machine answers.
NOTE:
Message Waiting cancel via "Dial 6 4 +
station number" only applies to VM ports that
have LEDs 16 and 17 set "ON" in Program
31.
• Ringing Modes, LED 03—Two choices are
available for ringing modes invoked by the
Night Transfer button. One choice consists
of the DAY, DAY 2, NIGHT modes (three
modes), and the other of the DAY and
NIGHT modes (two modes). The threemode selection is useful for alternate answering positions. These modes are
switched via the Night Transfer1/Night
Transfer2 button on a
telephone or
DSS Console (Programs 29 and 39) which
controls CO line ring assignments (Programs 78 and 81 ~ 89).
• Call Forward Override From DSS Console (DDSS or HDSS) Position, LED 02
(for STRATA DK16 only)—If a station has
activated call forwarding, all calls to that
station will be forwarded to another number—except for calls from the DSS console
position. A choice exists of whether to call
forward from the console itself or from the
digital or electronic telephone assigned to it.
If the console calls (using the DSS console
station buttons) are forwarded, the attendant telephone will not be forwarded, and
vice versa. This allows the console operator
flexibility in reaching a station user.
• Tone First/Voice First-DSS Console
(DDSS/DSS), LED 01 (for STRATA DK16
only)—The intercom call signal from a DSS
console can be set for Tone First Signaling
or Voice First Signaling, independent of the
system-wide signal option set in Program
10-1. Thus, DSS consoles and their atten-
NOTE:
The external amplifiers will also be automatically switched into two CO line DISA line
calls.
Program 12—System Assignments-Basic Timing:
• Pause Timing, Code 3—Short and long
pauses may be programmed in Speed Dial
numbers by station users. The length of
short pauses can be set system-wide for
either 1.5 or 3 seconds with Code 3. The
2-6
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
long pause (a different user selection) is
always 10 seconds. Pause timing applies to
Speed Dial on data calls made with Data
Interface Units (DIUs), as well as to Speed
Dial for regular voice calls.
• Flash Timing, Code 4—When on a CO line,
a station user can press the Flash button
and the CO line will open (flash) for a period
of either 2 seconds, 0.2 seconds, or 0.5
seconds depending on this assignment mode
with Code 4. A flash can also be activated by
pressing the Cnf/Trn button and dialing 4
5. In general, this choice reflects whether to
disconnect and regain dial tone (2 seconds)
or to use PBX or CENTREX features which
require a flash signal (0.5 seconds). This
flash timing also applies to flashes inserted
when dialing via Data Interface Units (DIUs).
may answer before the voice path is “cutthrough,” and the caller will not be heard. If
the time is too short, a standard telephone
user inputting DTMF tones could be cut off
prematurely from using other features, such
as Speed Dial, or Toll Restriction may be
defeated. (To prevent Toll Restriction defeat, force standard telephones to dial outgoing calls via Least Cost Routing (LCR).
When dialing via LCR, standard telephones
cannot defeat Toll Restriction if the QRCU/
K4RCU times out.)
NOTE:
If no digits are dialed after accessing an
outside line, the QRCU/K4RCU remains
seized for 15 seconds and then drops; however, the CO line remains connected.
Program 13—Defining the Message Center:
Each digital and electronic telephone can receive a maximum of four message waiting indications. One of these four is reserved for the
designated Message Center. Typically, the telephone accompanying an Add-On-Module on
DK8 or a DSS console (DDSS or HDSS) on
DK16 will be the Message Center. However, if
incoming traffic to an ADM or a DSS console
attendant is heavy, another station may be
assigned to be the Message Center.
NOTE:
The 0.2 seconds option is not normally used
in the United States.
• Pause After Flash, Code 5—Some Central
Offices or CENTREX facilities require a period of time after a flash signal before they
can accept dialing signals. A selection of
pause timing can be made with Code 5 to
automatically delay any dialing signals after
flash. This timing applies to speed dial calls
(with flash signals between the telephone
number digits) as well as manual dialing.
• QRCU/K4RCU Seize Time, Code 9—One
channel of the QRCU/K4RCU Dual-tone
Multi-frequency (DTMF) receiver/decoder
is seized when it is needed for the decoding
process, such as with a standard telephone
with a DTMF dialpad. When placing outgoing calls with DTMF standard telephones,
the talk path to the outside party is not “cutthrough” until the QRCU/K4RCU circuit is
released. The release time of the QRCU/
K4RCU channel can be programmed with
Code 9 for a time between one and nine
seconds (initialized timing is four seconds);
the release time is the time it takes to release
the QRCU/K4RCU circuit after the last digit
is dialed.
The choice of timing is a trade-off between
CO line time to connect and user speed. If
the time is too long, the outside called party
Program 15—Assigning Dial Pulse (DP)/Dualtone Multi-frequency (DTMF), Tenant Service to Individual CO Lines:
• Automatic Release (AR) on Voice Mail
(VM) Calls, Code 0—Some Central Offices
will send the AR signal—a 95 or 450-millisecond open of the CO line loop—after
(typically 1 ~ 15 seconds) an external party
hangs up to disconnect the CO line. If an
outside party hangs up before or after a VM/
auto attendant hookflashes to transfer a
call, the Central Office will send the AR
signal to the STRATA DK8 or DK16 system,
which will then send "D" (Program 31, LED
15) tone to the VM/auto attendant device to
release and clear the port for another call.
This feature is active on all voice calls. The
LCD of a station which is disconnected from
a CO line by the AR signal will display, "CO
LINE HANG UP" and the station will receive
2-7
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
• Automatic Release (AR) Time, Code 4—
busy tone. The CO line can be disconnected
by the AR signal anytime during the "talk
state" of a call. If a CO line is disconnected
by the AR signal, a "*" will print by the CO line
number on the SMDR report.
AR signaling timing is different depending
on the Central Office equipment. An assignment choice exists with Code 4 between
Crossbar or ESS Central Offices.
• Tandem CO Line Connection, Code 5—
Once a two CO line conference call is made
by a digital or electronic telephone user, that
user may drop out of the conference and
optionally leave the two CO lines connected.
The choice exists with Code 5 for each CO
line that may have this capability. This option must be enabled to allow CO lines to be
used for outgoing DISA calls.
• CO Line Tenant Assignment, Code 6—A
system may be effectively split into two parts
in order to serve two tenants using the same
system in a shared arrangement. This assignment dedicates CO lines to one tenant
or the other. If tenant service is not desired,
leave the assignments all for tenant 1, as
initialized.
IMPORTANT NOTE!
This option can not always be utilized
because some Central Offices may send
unreliable AR signaling or no AR signaling. Some Central Offices call the AR signal Calling Party Control or Loop Supervision.
• CO Outgoing Signal, Code 1 (for STRATA
DK16 only)—Each CO line can be independently assigned to have either Dial Pulse
(DP) or Dual-tone Multi-frequency (DTMF)
signaling.
• CO Dial Pulse (DP) Rate, Code 2—On
DK16, if a CO line is assigned Dial Pulse
(DP) signaling, the pulse rate can be set at
either 20 or 10 pulses per second. Some
Central Offices do not reliably accept 20
pulses per second. On DK8, CO line dial
pulse rate (10 or 20 PPS) is assigned for all
CO lines, system wide, in Program 10-1,
LED 14.
• Automatic Release (AR) From Hold/
Transfer, Code 3—Some Central Offices
will send the AR signal—a 95 or 450-millisecond open of the CO line loop—after
(typically 1 ~ 15 seconds) an external party
hangs up. If the system CO line is on hold (or
being transferred to another station) when
this signal occurs, it will be automatically
disconnected if this option is activated. TwoCO line DISA calls always release when AR
is sent, no matter what the Code 3 setting is.
If a CO line is disconnected by the AR signal,
a "*" will print by the CO line number on the
SMDR report.
NOTE:
The Night Transfer1 and Night Transfer2 buttons control CO ring modes for Tenants 1 and 2, respectively.
• Forced Account Code (Verified or
Nonverified), Code 7—If the Forced Account Code feature is used (Program 30), a
station user must enter an Account Code
before a CO line call can be completed. A
choice exists for each CO line.
• Operation After CO Line Flash, Code 8—
If a standard telephone user is on an existing
CO line call and performs a hookswitch
flash, a Dual-tone Multi-frequency (DTMF)
receiver channel may or may not be connected, depending on this assignment. If the
CO is a rotary dial only type, the QRCU or
K4RCU must be seized after flash when
dialing from DTMF standard telephones.
The QRCU or K4RCU will decode the dialed
tones and send dial pulses to the CO line.
IMPORTANT NOTE!
This option can not always be utilized
because some Central Offices may send
unreliable AR signaling or no AR signaling. Some Central Offices call the AR signal Calling Party Control or Loop Supervision.
Program 16—Assigning CO Line Groups: CO
lines may be accessed by dialing a code instead
of with a CO line button. Up to four groups may
be accessed for STRATA DK8 by dialing 81 ~
84. Up to eight groups may be accessed for
2-8
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
• DIU Connection, LED 01—Light this LED if
STRATA DK16 by dialing 81 ~ 88. This is useful
for WATS lines or other facilities and is heavily
used in Least Cost Routing and pooled line
button arrangements. A general group for outside calling is available with a dial 9 access
code, which is the initialized state for all CO
lines. Program 16 is used to assign each CO
line to one of these groups. Do not attempt to
assign a CO line to more than one group. A CO
line need not be assigned to a group. Unconnected CO lines should be taken out of all
groups, including the Dial 9 group. Automatic
Busy Redial (ABR) will not function if unconnected lines are assigned to a line group.
Program 19—Alternate Background Music
(BGM) Source Slot Assignment (Not necessary for DK8 BGM to QSTU.): An alternate BGM
source sent to digital telephones, electronic
telephones, and the external page output can
be connected to either a KSTU, PEKU, PSTU,
or PESU PCB. This program identifies the slot in
which the PCB resides. The optional KSTU can
only occupy Slot 03 in the Base Key Service
Unit; and the PSTU, PEKU, or PESU can be
installed in any slot in the Expansion Unit. After
completing Program 19, identify in Program
10-2, LED 09 or 10, whether a PEKU (Circuit 3
only), or PESU (Circuit 8 only) will be connected
to the alternate BGM source. These LED assignments are not necessary when connecting
the BGM source to the PSTU or KSTU (Circuit
4 only). When the alternate BGM source is
connected, the music source connected to the
MOH RCA jack in the Base Unit will continue to
be sent to CO lines or stations that are on hold.
there is an Integrated Data Interface Unit
PDIU-DI(2) or Stand-alone Data Interface
Unit (PDIU-DS) connected to the entered
digital port. Each PDIU-DI(2) uses the same
digital port as the station it is connected to,
and each PDIU-DS requires a separate digital port.
NOTE:
There are two types of Integrated Data Interface Units: the PDIU-DI and the PDIU-DI2.
These units are identical, except that the
PDIU-DI connects to 1000-series Digital Telephones, and the PDIU-DI2 connects to 2000series Digital Telephones.
• AT Commands and Result Codes, LED
02—If the DIU must respond to AT commands and return result codes, this LED
should be lit. DIU “AT” commands and “result” codes are listed in the Data Interface
User Guide. If LED 02 is not lit, the DIU will
only respond to AT dialing commands (ATDT,
ATD, and ATDD) and will not return result
codes. If the DIU is connected to a terminal
or a personal computer with communication
software, LED 02 should be ON. If the DIU
is connected to a modem, LED 02 should be
ON. If the DIU is connected to a printer, LED
02 should be OFF.
• PDIU-DS to Modem Connection, LED 03—
If a PDIU-DS is connected to the digital port,
identify whether the PDIU-DS is connected
to a modem (LED ON) or not connected to a
modem (LED OFF). If not connected to a
modem (LED OFF), the connected device
can be a DCE or DTE. This option is not
necessary for PDIU-DI(2)s, because they
are not normally connected to modems.
• PDIU-DS or PDIU-DI(2) Connection, LED
04—Light this LED if a PDIU-DS is connected to the digital port; leave OFF if a
PDIU-DI(2) is connected. Digital telephones
supporting PDIU-DI(2)s may require the
Data Call, Data Release, and Modem
buttons assigned to them in Program 39.
• Auto Pause Behind PBX, LED 05—If the
system CO lines are connected to a PBX,
CENTREX, or Central Office that is slow to
NOTE:
The alternate BGM source cannot be connected to any digital telephone circuit in DK16;
or DK8.
Program 20—Data Interface Unit (DIU) Configuration: This program identifies the digital
station ports connected to DIUs and the type of
DIU connected.
NOTE:
DIUs can be connected to any digital circuit in
the Base Key Service Unit or on the KCDU or
PDKU2, but only on Circuits 1 ~ 7 on the
PDKU1.
2-9
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
• PDIU-DS Connected to a Modem—LEDs
return dial tone after seizure, light this LED
to insert a pause before and after the PBX or
CENTREX access code is dialed by the
DIU; LED 05 should also be lit to automatically insert a pause before network telephone numbers are autodialed by DIUs.
01, 02, 03, 04, 06, and 17 ON; all other LEDs
OFF.
Program 21—Modem Pool Port Assignments:
With this program, identify modems connected
to standard telephone ports (line side of modem) and PDIU-DS ports (RS-232 side of modem). Each selection pair assigns the modem to
the system modem pool. With data security
groups (Program 20, LEDs 17 ~ 20) and the call
blocking feature (Program 31, LED 04), modem
access can be denied or allowed to data users.
NOTE:
The pause length is set in Program 12-3, and
CO lines behind PBX/CENTREX are assigned
in Programs 42-0 and 42-1 ~ 8.
• DTR Pulse, LED 06—If a PDIU-DS is con-
nected to a modem, turn LED 06 ON to
cause the modem to disconnect the line
when a digital telephone user presses the
Data Release button. When the button is
pressed, the PDIU-DS sends a DTR pulse to
the modem, which disconnects the line when
it receives the pulse. The PDIU-DS will
pulse DTR on outgoing modem calls only—
not on incoming modem calls. Initially, the
modem should be sent AT command "AT &
D2" so it can recognize DTR pulse sent to it
by PDIU-DS.
NOTES:
1. To provide data security for modems, turn
ON LED 18 in Program 31 for standard
telephone ports supporting modems. To
allow callers to switch from voice to data,
turn OFF LED 18 for standard telephone
ports supporting modems.
2. Digital telephones with PDIU-DI(2)s that
must access modems from a pool require
that a Modem button be assigned to
them in Program 39.
3. PDIU-DS ports that are connected to
modems in the modem pool should be set
with LEDs 01, 02, 03, 04, and 06 ON in
Program 20.
4. If a modem that is connected to PDIU-DS
is also connected to a telephone network
CO line, instead of a standard telephone
port, Program 21 should not be used.
5. Use Program 22 to assign modem/PDIUDS stations to a hunt sequence.
6. DIUs can be connected to any digital
circuit in the DK8 KSU or DK16 Base Unit;
or on the QCDU (STRATA DK8), KCDU
(STRATA DK16), or PDKU2, but can only
connect to Circuits 1 ~ 7 on the PDKU1.
NOTE:
It is recommended to change the escape
sequence (typically + + +) of a modem connected to a PDIU-DS. Separate sequences
will enable users to escape from a modem or
a DIU more selectively. Escape sequences
are changed with the "ATS2 = ___" command.
• Security Groups, LEDs 17 ~ 20—Data
security groups can be set to block data calls
between DIUs. DIU users can only make
data calls to DIUs in the same security
group. LEDs 17 ~ 20 assign the DIU to the
appropriate security group: light LED 17 for
group 1; LED 18, for group 3; LED 19, for
group 2; and LED 20, for group 4.
Program 22—Data Interface Unit (DIU) Station
Hunting: If a DIU station (printer, modem, etc.)
is busy, data station hunting allows the data call
to that station to hunt to an alternate DIU station
assigned in this program. If the hunted DIU
station is busy, the system will ring the next
“hunt-to” station, and so on. If all DIU stations in
Typical LED settings for Program 20.
• PDIU-DI(2) Connected to a Terminal or
Personal Computer—LEDs 01, 02, 05, and
17 ON; all other LEDs OFF.
• PDIU-DS Connected to a Printer—LEDs
01, 04, and 17 ON; all other LEDs OFF.
2-10
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
the “hunt-to” sequence are busy, then the data
caller will receive a busy tone. It is recommended that all PDIU-DS station ports grouped
in a modem pooling or printer pooling/server
configuration be placed into a hunt-sequence
arrangement with Program 22. Program 22
applies to PDIU-DS and PDIU-DI(2) data stations, not telephone stations. (See Program 33
for telephone station hunting.)
Program 29—DSS Console Button Assignments (for STRATA DK16 only): The buttons on
the DSS console (DDSS and HDSS consoles)
may be flexibly assigned as Direct Station Selection (DSS) buttons, CO line buttons (Line),
or Speed Dial (SD) buttons. The standard
equipped Night Transfer and All Call Page
buttons may be changed to either a DSS, Line,
or SD buttons, but not vice versa. Station Speed
Dial buttons assigned to a DSS console share
the associated attendant telephone’s Speed
Dial memory—The Station Speed Dial numbers
of the DSS circuit port(s) are not available.
Initialized data assigns the DSS console with 20
DSS button (for stations 10 ~ 29), 38 SD
buttons (for Station Speed Dial codes 10 ~ 47),
All Call Page, and Night Transfer. Each
of the two possible DSS consoles can be
independently programmed.
NOTE:
When a PDIU-DS is connected to a modem
assigned to the system modem pool in Program 21, modem hunting is automatic when
a digital telephone user equipped with a PDIUDI(2) presses the DATA button to transfer a
CO line call to a modem; however, if the user
dials the modem's PDIU-DS's station number, modem hunting will follow the hunt sequence specified in Program 22.
Program 30—Station Class of Service:
• Privacy Override, LED 19—Privacy Override allows a station to enter into and overhear an existing CO line conversation by
pressing a common CO line button. A maximum of two stations may override an existing station-to-CO line conversation. An optional warning tone may be set—see Program 10-2. The choice is for which station is
allowed to override calls with Privacy Override. Privacy Override of DISA two-CO line
calls is not allowed.
Program 28—DSS Console/Attendant Telephone Assignments (for STRATA DK16 only):
A system configured with just a Base Key Service Unit can support one DSS console; a system configured with the optional Expansion Unit
can support up to two DSS consoles. There are
two types of DSS consoles: the DDSS console
and the HDSS console. A DDSS console can be
connected to Circuit 8 of the Base Unit or Circuit
8 of a PDKU. An HDSS console can only be
connected to Circuits 7 and 8 of PEKU.
A DSS console can only be associated with
just one telephone, but a telephone can have as
many as two consoles associated with it. When
a DDSS console is connected to the Base Unit,
it is automatically assigned to the digital telephone connected to the first digital circuit on the
Base Unit. When a console is connected to a
PEKU or PDKU in the Expansion Unit, the
console is automatically assigned to the telephone that is connected to the first circuit on the
PCB. These default assignments can be
changed with this program. So, for example, the
DDSS console connected to the Base Unit could
be assigned to operate with another DSS console and telephone connected to the Expansion
Unit.
NOTES:
1. To configure the DK8/DK16 system to
operate as nonprivate, allow Privacy Override from all stations.
2. Privacy Override can be blocked by a
station via the Privacy on Line button
(Program 39) or by the Executive/Privacy Override blocking option (Program
31, LED 18).
3. See Table 2-C at the end of this chapter
for more information on Privacy options.
• Executive Override, LED 18—Executive
Override allows a station to break into and
overhear an existing station conversation by
2-11
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
dialing 3 after the busy station number. An
optional warning tone may be set—see Program 10-2. The option is for which calling
station can use Executive Override.
(Forced or Voluntary) dialed by the station
user (or DISA line user) will be Verified per
Account Codes set in Program 69. If the
station user fails to dial one of these specific
Verified Account Codes, the call cannot be
executed (Forced), or the Account Code will
not be validated for the SMDR call report
(Voluntary).
• Handset/Headset Volume Level, LEDs 12
and 13—This program sets the initial handset and/or headset (off-hook) volume level
for each digital telephone. This level can be
changed with the digital telephone’s volume
control button while the handset/headset or
headset is off-hook, but it will return to the
default level set in this program after the
handset/headset is placed on-hook.
§ The volume level range for digital telephone handsets/headsets is 1 ~ 9, with
1 as the lowest. Anytime a handset is offhook, its volume level can be adjusted
anywhere between 1 ~ 9. The level
setting established in this program, however, can only be from 2 ~ 5. This level
is set with LEDs 12 and 13:
For level 5: Both LEDs ON (High)
For level 4: LED 12, OFF; LED 13, ON
For level 3: LED 12, ON; LED 13, OFF
(Initialized setting)
For level 2: Both LEDs OFF (Low)
NOTE:
Executive Override can be blocked by stations that have Executive/Privacy Override
blocking enabled in Program 31, LED 18;
the Privacy on Line button does not block
Executive Override. See Table 2-C at the end
of this chapter for more information on Privacy options.
• Do Not Disturb (DND) Override, LED 17—
•
•
•
When called, a station with DND activated
will return very fast busy tone (four tones per
second). If the caller presses the additional
digit 2 on the dialpad, a DND Override tone
will be heard on the called station’s speaker.
The assignment is for which calling station
can use DND Override. Stations must have
a Do Not Disturb button to activate DND.
Toll Restriction/Traveling Class Code
Change, LED 16—If this LED is lit for a port,
the station occupying it can change the four
digit Toll Restriction/Traveling Class of Service codes established in Program 44B.
Stations selected for this feature must dial
the following sequences to change the
codes:
Class 1: Intercom + 6 2 2 + the four-digit
code + Redial
Class 2: Intercom + 6 2 3 + the four-digit
code + Redial
Class 3: Intercom + 6 2 4 + the four-digit
code + Redial
Class 4: Intercom + 6 2 5 + the four-digit
code + Redial
Verified Account Code Change, LED 15—
If selected for this feature, a station can
change the Verified Account Codes established in Program 69. Selected stations
must dial the following sequence to change
the codes:
Intercom + 6 5 9 + 0 0 0 ~ 2 9 9 +
Verified Account Code + Redial (on
DK16)
Intercom + 6 5 9 + 0 0 0 ~ 0 9 9 +
Verified Account Code + Redial (on
DK8)
Verified Account Code, LED 14—If this
feature is selected, all Account Codes
NOTE:
Program 92-5 (LEDs 01 and 05) does not
affect handset/headset receiver volume levels.
• Dial Pulse (Dual-tone Multi-frequency
Off), LED 11—If any device connected to a
QSTU, KSTU, PSTU, or PESU port does not
require the QRCU/K4RCU for DTMF decoding, it should be programmed for dial pulse
(DP). When that device goes off-hook, the
QRCU/K4RCU will not be accessed, reducing potential traffic to the QRCU/K4RCU.
• Change Direct Inward System Access
(DISA) Security Code, LED 10—This allows a selected station to change the DISA
security code by dialing Intercom + 6 5 8
+ New Code + REDIAL.
• Change Toll Restriction Override Code,
LED 09—Two Toll Restriction Override
codes are available in the system. When
2-12
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
NOTE:
When receiving intercom calls, the flexible
Microphn Cut-off button (Program 39)
can control the microphone to prevent room
monitoring and handsfree answerback.
one of these codes is dialed at any station,
all Toll Restriction for that station is bypassed. These codes can be changed only
by stations assigned in this program by
dialing Intercom + 6 5 4 or Intercom +
6 5 5 for codes 1 and 2, respectively.
• Forced Account Code, LED 08—If this
feature is selected, a station or DISA line
user (attempting to make a call on a CO line
with Forced Account Code required in Program 15-7) is required to enter an Account
Code before a CO line call can be completed. If Forced Account Codes should be
Verified, turn on LED 14 in Program 30. The
digit length of Forced Account Codes is
determined in Program 60-4.
• Off-hook Call Announce (OCA) Automatic, LED 07—A busy (off-hook) digital or
electronic telephone can receive a second
voice communication on intercom via Handsfree Answerback if it is equipped with on
OCA subassembly. If a calling station does
not have the automatic function, the user
must dial an extra digit of 2 or 21 after
hearing busy tone in order to gain access to
OCA. Initialized data makes all stations automatic for OCA.
• Automatic Busy Redial (ABR) Access,
LED 06—The ABR feature can be enabled
or denied for each station. The system will
select the last CO line in the originating line
group each time ABR is initiated. If ABR
access is denied to a digital telephone station in this program, the "ABR" Soft Key will
never appear on the station's LCD. Refer to
LEDs 11 and 12 in Program 10-1 for more
ABR programming.
• Mic Button Lock, LED 02—A digital or
electronic telephone microphone can be
turned on or off by using the Mic button.
Two modes of operation are available. A
momentary operation requires that the Mic
button be continuously pressed to disable
the microphone. A Button Lock operation
allows an alternate action Push On/Push Off
of the Mic button. LED 02 should be ON if
microphone lock operation is desired.
• Speakerphone Enabled, LED 01—Any digital or electronic full speakerphone operation
can be disabled by assignment with this
program. If disabled, a speakerphone will
act as a handsfree electronic or digital telephone. Initialized data enables all speakerphones.
Program 31—Station Class of Service: This
program sets most voice mail (VM) port assignments. Each QSTU/KSTU/PESU/PSTU port
connected to a VM device should have the
following LEDs turned ON: 04, 05, 09, 15, 16,
17, 18, 19, 20. These LED's should be set ON for
VM ports only, not for telephone ports.
NOTE:
LED 04 may be ON or OFF, depending on VM
device operation. See the LED 04 write up
that follows.
• VP (B + Station Number), LED 20—This
feature is associated with a VP Digital Voice
Messaging System connected to a QSTU,
KSTU, PSTU, or PESU port. DTMF “B” tone
followed by the station number is sent to VP
in situations in which VP would not normally
know the location from which a call was
coming, such as hold recall or blind ring
transfer recall. This allows VP to respond
more intelligently with appropriate voice
prompts. This LED should be lit for QSTU,
KSTU, PSTU, or PESU ports connected to
VM devices only, not for station ports connected to telephones.
IMPORTANT NOTE!
For ABR to function, the QRCU (DK8) or
the K4RCU (DK16) must be installed to
provide busy tone detection.
• Microphone (Mic Button) On at Start of
Call, LED 03—The microphone (and Mic
button LED) can be selected to be ON or
OFF at the start of a call if the Push On/Push
Off mode (see "Mic Button Lock," LED 02) is
chosen.
2-13
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
NOTE:
"LED 19, "VP (B + No Station)," must be
enabled to allow this function.
• VP (B + No Station), LED 19—DTMF “B”
tone is sent to VP to signify a recall situation
where VP already knows the recalling station number. Again, this allows VP to respond more intelligently with appropriate
voice prompts. This LED should be lit for
QSTU, KSTU, PSTU, or PESU ports connected to VM devices only, not for station
ports connected to telephones.
• Executive and Privacy Override Blocking (Modem), LED 18—This feature denies
any other station to break in with Privacy or
Executive Override to the called station’s
connection. It should be used for QSTU,
KSTU, PSTU, and PESU ports connected to
a modem or Voice Mail/Auto Attendant in
order to ensure data and voice security at
that port. This feature may also be used to
deny override of any station.
•
•
NOTES:
1. The Privacy Release button may be
used to disable privacy blocking on a callby-call basis; this button cannot disable
Executive Override blocking.
2. If a modem is assigned to the system
modem pool in Program 21, use this
option to provide data security.
3. If using the system modem pool for data
calls that must be switched between voice
and data, LED 18 should be OFF for the
modem standard telephone ports assigned in Program 21.
•
•
• End/End Signal RCV (Voice Mail), LED
17—Activation of this option allows End to
End Signaling of Dual-tone Multi-frequency
(DTMF) tones through the system. It is required on all voice mail-QSTU/KSTU/PSTU/
PESU ports in order to have proper signaling communication.
• Receive Voice Mail (VM) ID Code, LED
16—When a station is call forwarded to a
VM system, certain identification (ID) Dualtone Multi-frequency (DTMF) tones will automatically be sent to direct the call to a
•
2-14
specific mailbox (VM ID Code 656). The
automatic ID is also sent to the VM device
when digital or electronic telephone users
retrieve messages via the Intercom and
Msg buttons (VM ID Code 657). The VM
port must be programmed for this feature to
receive DTMF digits.
VP Integration (A Tone/D Tone), LED 15—
This option will cause an answer tone (DTMF
“A” tone) to be automatically sent to VP
when a station answers, and a disconnect
tone (DTMF “D” tone) when a station disconnects. This allows VP to respond quickly
rather than waiting a long time in time-out
situations. If the Central Office provides the
Automatic Release (AR) signal, "D" tone is
also sent to disconnect VM ports when outside callers hang up (Programs 15-0 and
15-3).
Group Page 1 ~ 4, LEDs 11 ~ 14—Intercom
paging can be directed to digital and/or
electronic telephone speakers in a group
arrangement. Up to four groups are possible. This program assigns each digital and
electronic telephone to the groups. Telephones can be assigned to as many groups
as desired.
All Call Page Allowed-Digital and Electronic Telephones, LED 10—Any digital or
electronic telephone may be allowed to receive an All Call Page. This does not alter
the station’s ability to initiate an All Call
Page. Initialized data allows every port to
receive an All Call Page.
Voice Mail (No Conference), LED 09—If
LED 09 is activated, a station is prohibited
from having any CO line conference calls.
This feature should be used for voice mail
ports in order to prevent undesirable conference calls.
Voice Mail (VM) Groups 1 ~ 2, LEDs 05 ~
06 (STRATA DK8); Groups 1 ~ 4, LEDs 05
~ 08 (STRATA DK16)—The system allows
up to two (DK8) or four (DK16) VM station
port groups to be configured for support of
up to two (DK8) or four (DK16) voice mail or
auto attendant devices. One group is intended for each different machine. All QSTU,
KSTU, PSTU, and PESU ports connected
to a particular VM machine should be as-
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
•
•
•
•
a CO line button or dial an access code. If no CO
lines are ringing and a digital or electronic telephone goes off-hook, the station can be automatically connected to intercom or to a CO line.
The CO line connected can be the lowest numbered CO line available on the telephone or the
highest idle CO line from a selected group (1 ~
8).
signed to the same VM group. The purpose
of the VM grouping is to allow efficient use
of the message waiting set and cancel operations from the VM machines. Since each
digital and electronic telephone can only
have a maximum of four messages waiting,
the voice mail device should set MW only
once, regardless of how many messages
there are.
Voice Mail (VM) to VM Call Blocking, LED
04—This prevents VM/auto attendant ports
from call forwarding to other VM ports during
screened or supervised VM transfers. If VM/
auto attendant calls are screened or supervised, this LED should be ON for all VM/auto
attendant ports; if VM/auto attendant calls
are blind transferred, this LED should be
OFF for all VM/auto attendant ports.
Off-hook Call Announce (OCA) Enabled
(Receive), LED 03—Any digital or electronic telephone equipped for OCA should
be assigned this option. If assigned, the
station will be allowed to receive OCA. This
program does not affect the station’s ability
to originate OCA.
Handsfree No Warning, LED 02—Normally, a one-second warning tone is sent to
a handsfree digital or electronic telephone
to inform the user that someone is calling
and that they can be heard. If the warning
tone is not desired at the called digital or
electronic telephone, this assignment can
disable it. This will also prevent ringing the
digital or electronic telephone as a ring-first
situation, allowing silent room monitoring of
the area surrounding the telephone. Initialized data activates the warning tone for all
ports.
Handsfree Disabled, LED 01—It is possible to disable the intercom handsfree function on any digital or electronic telephone.
NOTE:
This program does not apply to standard
telephones. To allow system features to be
accessed, standard telephones always receive system intercom dial tone when originating calls.
Program 33—Station Hunting (Voice Calls
Only): If a station is busy, Station Hunting allows
the ringing of an alternate station as defined by
the assignments in this program. If the "hunt-to"
station is busy, the system will try to ring the next
"hunt-to" station, and so on. If a "hunt-to" station
is in the Call Forward mode, the Call Forward
overrides the hunt. A CO Line will hunt from a
station only if it has been assigned to ring at that
station exclusively (see Programs 81 ~ 89).
Program 34—Hold/Park Recall Timing: Each
station can have a different time (from 011 to
160 seconds) for Hold/Park Recall. The time is
the duration between the point when the call is
placed on hold or parked and the point when the
held or parked should recall the station that
placed it on hold or parked it.
Program 35—Station Class of Service:
• Busy Station Transfer with LED 20 and
Busy Station Ringing with LED 19—Busy
Station Transfer (BST) and Busy Station
Ringing (BSR) operate together to ensure
that a busy digital or electronic telephone
station always receives transferred CO line
calls along with LED and tone indications.
The station or Voice mail (VM)/auto attendant device that transfers the call must be
programmed with BST (LED 20 ON) and the
one that receives it must have BSR (LED
19). When a busy station with BSR receives
a transfer from a station or VM/auto attendant with BST, there will be a muted repetitive tone (1 second ON, 3 seconds OFF) at
the busy station and the intercom LED will
flash at the ringing rate until the station
Program 32—Automatic Preference: Automatic
Preference for digital or electronic telephones
(see Note) via handset off-hook or the Spkr
button is the automatic connection to CO lines or
intercom under various conditions. With Ringing Line Preference, a digital or electronic telephone going off-hook (or pressing the Spkr
button) may be automatically connected to the
lowest CO line ringing in without having to press
2-15
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
from being forwarded 12 seconds after the
called party has been talking. Outside calls
and busy intercom calls to the station will
forward even if this feature is set. This feature
does not apply to off-hook call announce calls;
the called station must answer an OCA call
within 12 seconds or the call will be forwarded
if CFNA is set.
transferring the call hangs up. When it does
hang up, the CO line call will then camp-on to
the busy station. The busy station will be
alerted of the camp-on by a camp-on tone (five
quick tone bursts), the CO line LED will flash
at the exclusive hold rate, and a message
(“CAMP-ON X”, X = the CO line number) will
appear on the LCD (if equipped). Among other
applications, one in which a VM/auto attendant device that transfers calls to a typically
busy answering position station will benefit
from this feature—some auto attendant devices cannot transfer a call to a busy station if
BST and BSR are not activated.
NOTE:
The caller can press the "RING" Soft Key on a
digital telephone or dial 1 on a digital or electronic telephone to activate Call Forward on
Handsfree Answerback calls.
• LCD Individual Message, LED 05—Turn
NOTE:
A BST station will receive ringback tone, instead of busy tone, when transferring a call to a
busy BSR station.
LED 05 ON to allow stations to store up to
ten personal LCD messages. Stations selected with this feature will also be able to
assign alphanumeric memos to each of their
personal Speed Dial numbers.
• Message Waiting (RCV), LED 04—If the
message waiting indication is not desired on
a digital or electronic telephone, this program can be used to deny it. This does not
affect that station’s ability to send a message waiting indication to another station.
• LCD Type/32/12, LED 02—Digital telephones and 6500-series LCD Electronic
Telephones have a 32-character display.
Therefore, assignments should be left in the
initialized state of 32 characters. LED 02
must be ON to receive a voice mail message
waiting indication.
• LCD Display, LED 01—This option should
be used (LED 01 ON) for all stations (even
non-LCD) unless it is desired to disable the
station's LCD and message waiting LED
function.
Program 36—Fixed Call Forward: Fixed Call
Forwarding is different from other station Call
Forwarding options. It is fixed in terms of the
destination station number which is assigned in
this program. The station user cannot change
this destination as is possible with other station
Call Forwarding options. This feature is valuable for forwarding to voice mail devices or to an
attendant. If Fixed Call Forwarding is set on a
station, the station will not ring and all calls will
forward.
• Automatic Hold, LED 18—If this feature is
allowed, digital and electronic telephone users with CO line buttons can place a CO line or
intercom call on hold and call another CO line
or station just by pressing another CO line
button or the Intercom button and dialing the
number—there is no need to press the Hold
button to place the existing call on hold. If
Automatic Hold is denied with this LED, users
can put calls on hold and place calls, but they
will have to press the Hold button before
accessing another CO or intercom line.
NOTES:
1. CO lines or intercom calls that appear on
the intercom button will automatically hold
when accessing another CO line button.
2. If Automatic Hold is used, it is recommended
to program a Release Call button on
telephones via Program 39.
• Disable Continuous DTMF tones, LED 17—
Turns off continuous DTMF tones on 2000series Digital telephones—may be required
for PC dialing telephone numbers using PDIUDI2 connected to a DKT 2000 telephone.
• No Call Forward/No Answer on Handsfree
Answerback Call, LED 16—A Handsfree
Answerback call to an idle station in the Call
Forward-No Answer mode or in the Call Forward-Busy/No Answer mode will not forward if
this feature is activated. This prevents the call
2-16
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
nected to a PBX or to CENTREX. This combination allows Toll Restriction and Speed Dialing to
function properly. This program must be utilized
to allow (after flash) PBX/CENTREX features to
operate on incoming calls.
Program 43—0+ Credit Card Dialing Option:
Selected stations can bypass their normal Toll
Restriction assignment by seizing a CO line and
then dialing a 0. Both the station and the CO line
must be enabled for this feature with this program. After seizing the CO line, the station user
is required to dial a specific number of digits,
which includes the leading 0. This digit-length
requirement forces the user to dial a telephone
number or a telephone number plus a credit
card number; as a result, these calls are billed to
the credit card, and operator-placed calls are
not billed to the CO line. The digit length, 1 ~ 30
numbers, is set in Program 60-7. This length is
determined by the system’s call routing method.
• If calls are routed via Least Cost Routing
(LCR), the digit length should usually be set
at 12, the length, including 0, of the telephone numbers dialed on 0+ credit card
calls. Do not add the amount of digits in the
credit card (usually 14), although these numbers will be dialed by the user after system
LCR seizes the line and the system dials the
telephone number (see Important Note).
• When not dialing via LCR, the digit length
should usually be 26, the sum of the digits in
the telephone (12) and credit card (14) numbers.
Program 37—Ring Transfer (Camp-on) Recall
Time: If a busy or ringing station does not
answer a call sent to it via call transfer, the
station originating the transfer will be recalled
after a certain amount of time. This time (011 ~
999 seconds) is set independently for each
originating station by this program. Initialized
data sets all stations for a 32-second recall time.
Ring Transfer must first be enabled for the
system with LED 07 ON in Program 10-1.
Program 38—Digital and Electronic Telephone
Buttonstrip Type: Four digital and four electronic telephone button arrangements are provided (see System Record Sheet). It is best to
start with one of these four and then move on to
Program 39 where individual buttons may be
programmed.
Program 39—Flexible Button Assignments: See
Program 38 before running this program. Program 39 enables each of the flexible feature
buttons on digital and electronic telephones to
be individually assigned with features. See the
Program 39 System Record Sheet for a complete listing of the available features.
Program 40—Station CO Line Access: Any station can have access to as many CO lines as
desired. Any station denied access (either to
make a call or to answer a call) to a CO line
cannot seize that line by dialing an access or
pickup code or by using a CO line button. This
also denies access via Least Cost Routing. Use
this program to divide CO lines for Tenant Service. If only outgoing access is to be prevented,
use Program 41. Use Program 40 to deny CO
line call pickup.
Program 41—Station Outgoing Call Restriction: Each station (or Direct Inward System
Access CO line) can be restricted from outgoing
access to each CO line. If so restricted, that
station can still answer a ringing CO line or pick
up a call on hold. All Call Pickup functions
operate normally. This does not deny access via
LCR. Automatic Busy Redial (ABR) overrides
Program 41.
Program 42—CO Line To PBX/CENTREX Connection & PBX/CENTREX Access Codes: The
system recognizes PBX/CENTREX access
codes via Programs 42-1 ~ 8. Program 42-0
informs the software which CO lines are con-
IMPORTANT NOTE!
More digits than the length set in Program
60-7 are allowed to be dialed; there is no
limit to the amount of digits that can be
dialed.
Program 44A—Emergency Bypass of Forced/
Verified Account Codes: This program exempts numbers up to four digits, such as the
emergency 911 number, from Forced/Verified
Account Code dialing restrictions. As many as
three of these special numbers can be programmed. When dialed, these numbers will be
sent out the CO line immediately, bypassing any
Forced/Verified Account Code dialing restric-
2-17
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
tions set in Programs 69 and 30 (LEDs 8 and
14). If CO lines are behind CENTREX or PBX,
program the appropriate one-digit or two-digit
CENTREX/PBX trunk access code in front of
the emergency number. Example: If the PBX
trunk access code is 8, then program 8911 in
Program 44A-51 to allow 911 to bypass Forced/
Verified Account Code dial requirements.
•
NOTES:
1. If CO lines are behind PBX or CENTREX,
program the PBX/CENTREX outside trunk
access code. (See Program 42-0 and
42-1 to assign CO lines and access codes
for behind PBX/CENTREX operation.)
2. If Verified Account Codes assigned in
Program 69 conflict (duplicate) with emergency or other type telephone numbers
set in Program 44A, Program 44A has
priority.
3. Toll Restriction and Direct Inward System
Access (DISA) parameters requirements
are not affected by this program.
•
•
Programs 45 ~ 48—Toll Restriction: All Toll
Restriction program information is provided later
in this chapter.
Programs 50 ~ 56—Least Cost Routing: All
Least Cost Routing program information is provided later in this chapter.
Program 60—Station Message Detail Recording (SMDR) Output/Account Code Digit
Length:
• SMDR Threshold Time, Item 2—The time
that a call must be in progress before it will
register with SMDR can be set to 1 second
or 10 seconds. The default is 10 seconds.
• SMDR Output, Item 3—System output to
an SMDR device can include information for
both incoming and outgoing calls, or only for
outgoing calls. Local and long distance call
data will be sent out.
• Forced/Voluntary/Verified Account Code
Digit Length, Item 4—The Account Code
entered at a station can vary in length from
4 ~ 15 digits. For Forced Account Code use,
•
2-18
a call will not be completed unless the specified number of digits is entered by a station
user. With Voluntary Account Codes, the
Account Code will not be sent to the SMDR
call record unless the specified number of
digits are dialed. See Program 69 for Verified Account Codes.
SMDR Printout Options, Item 5—This
option selectively deletes local call data and
allows long distance/toll call data only to be
sent out the SMDR port. The type of long
distance/toll call data that prints out is selected by long distance prefix codes 0, 1, 00,
or 1 or 0.
Direct Inward System Access (DISA) Security Code, Item 6—A security code (1 ~
15 digits) can be required for incoming DISA
calls to access outgoing CO lines. If the
DISA security code is not set in programming, DISA users can access outgoing CO
lines without dialing a security code. This
code is not required for DISA calls to stations. The DISA security code can also be
changed from stations enabled in Program
30.
Credit Card Call Digit Length, Item 07—
Station users bypassing Toll Restriction with
the “0+” Credit Card Calling feature (Program 43) must dial a predetermined number of digits including the “0.” This predetermined number is established with Item 7 and
can be 1 ~ 30 digits.Program 69—Verified
Account Codes: Verified Account Codes
may be added, deleted, or changed with
Program 69. The STRATA DK8 allows a
maximum of 100 Verified Account Codes;
the Strata DK16 allows a maximum of 300.
Each Verified Account Code can be 1 ~ 15
digits long, but cannot exceed the overall
Account Code length requirement set in
Program 60-4. The following programs and
options should be considered when establishing Verified Account Codes.
Account Code Digit Length—Program
60-4 sets the digit length that must be dialed
for all Account Codes: Forced (Verified/
Nonverified) and Voluntary (Verified/
Nonverified).
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
• Full and Partially Verified Account
•
•
•
System Access (DISA) callers that access
outgoing CO lines can be required to enter
Verified Account Codes with Program 30
(LED 08 ON for Port 20).
Codes—Verified Account Codes can contain the same number of digits (full Verified
Account Code) or less (partially Verified
Account Code) than the Account Code length
set in Program 60-4. If partially Verified, the
first part of the Account Code is verified and
the remainder is not. For example, if Verified
Account Code 2734 is set in Program 69,
but the Account Code digit length is set to
eight in Program 60-4, then the user must
dial 2734 plus any other four digits to enter
a partially Verified Account Code. There are
many applications for partially Verified Account Codes. For instance, using the code in
the example above, the numbers 2734 could
be the user’s dial restriction code and the
remaining four digits could be a customerclient code, a sales order, etc.
Verified Account Code Toll Restriction
Assignments—A Toll Restriction class can
be assigned with Program 70 to each of the
Verified Account Codes.
Verified Account Code Dial Requirement—The Verified Account Code Dial Requirement is assigned on a station-by-station basis in Program 30, LED 14 ON. All
Account Codes dialed (Forced or Voluntary)
from stations assigned in this program will
be Verified.
Verified Account Code Change by Station—Stations selected in Program 30, LED
15 ON, can change Verified Account Codes
(VAC) by dialing the following sequence:
Intercom + 6 5 9 + 0 0 0 ~ 2 9 9 +
VAC+ Redial
Program 70—Verified Account Code Toll Restriction Assignments: A Toll Restriction class
can be assigned with this program to each of the
Verified Account Codes assigned in Program
69. Therefore, when a Forced Verified Account
Code is dialed at a station, the station temporarily assumes the Toll Restriction class assigned to the Verified Account Code. When
Program 70 is initialized, all Verified Account
Codes are assigned as not Toll Restricted (data
= 00). Verified Account Code Toll Restriction
class assignments are not user programmable;
so if the assignments are not known, it is recommended to assign a number (block) of Verified
Account Codes to each type of Toll Restriction
class. For example:
VACs 000 ~ 025 = No restriction
VACs 026 ~ 075 = Total restriction
VACs 076 ~ 099 = Class 1
etc.
Program 77-1—Peripheral Options:
• Door Lock Time, LED 20—The door lock
relay contacts on the PIOU, PIOUS, and
Door Phone/Lock Control Unit (DDCB) may
be programmed to operate for either three or
six seconds.
• DDCB Port Assignment, LEDs 16 and
17—Door Phone/Lock Control Unit (DDCB)
assignments are defined by this program.
DDCBs can only be connected to Ports 02
and 03 of the DK8 KSU, or Ports 04 (in the
DK16 Base Key Service Unit) and 12 (in the
DK16 Expansion Unit). After assigning the
DDCB(s), door phone numbers (551 ~ 556
for STRATA DK8 and DK16) will effectively
replace the station number assignment(s) in
Program 04. The door lock option is set via
Program 77-2.
• IMDU Modem, LED 14 (for STRATA DK16
only)—Turn LED 14 ON if the optional PIOU
or PIOUS PCB will be equipped for Remote
Maintenance with the IMDU modem subassembly. The IMDU's station number is 619
(unless the access code prefix has been
changed with Program 05).
NOTE:
DK8 provides 100 verified account codes
(000-099) and DK16 provides 300 (000-299).
• Verified Account Codes: Forced/Volun-
tary Program Options—Any station can
dial a Voluntary Account Code after accessing a CO line. Forced Account Code requirements are assigned via station and CO line
program options: Stations are assigned in
Program 30 (LED 08 ON), and CO lines are
assigned in Program 15-7. Stations must
dial Verified Account Codes when assigned
in Program 30 (LED 14 ON). Direct Inward
2-19
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
• Night Ringing over External Page Zones,
• In one of the modes (LED 06 ON), the
LEDs 10 ~ 13 (for STRATA DK16 only):
Tenant 1 or Tenant 2 CO lines can be
selected with this program to selectively
night ring external page zones. For this
feature to work, the appropriate CO lines
must be programmed to night ring over
external page in Program 78. Tenant assignments are made in Program 15.
relay will activate for one second and
then become idle for three seconds when
a CO line rings (incoming) and the system is in the NIGHT mode. The relay in
this mode is intended for applications
where CO Lines are assigned to ring an
external ringing device during the NIGHT
mode. For this mode to work, Ring Over
External Page must be assigned in Program 78 to CO lines.
• In the other mode (LED 06 OFF), the
relay will activate continuously when the
system is in the NIGHT mode and the
Night Transfer1 (not the Night Transfer2) button is on. One application of this
mode is to control an external answering
machine.
• MOH/NT Relay, LED 05 (for STRATA DK16
only)—A relay on the PIOU and PIOUS can
be assigned for Night Transfer applications
(see LED 06, "NT Relay Mode Assignment")
or for ON-OFF control of a Music-on-Hold
(MOH) source, such as a tape player. With
the MOH application, the relay will be activated only when a CO line or station is
placed on hold.
NOTE:
The PIOU option PCB must be installed to
allow this option.
• Door Phone Ring On External Page, LED
08—If a door phone button is pressed, a ring
tone can be enabled or disabled to external
paging when the system is in the NIGHT
mode. Activation of a Night Transfer1
button is required for door phones to ring
external page. The Night Transfer2 button does not apply to door phones.
• PIOU or PIOUS Door Lock Relay/External
Page Relay, LED 07 (for STRATA DK16
only)—A relay on the PIOU or PIOUS can be
assigned to operate with the Door Lock
function or with External Page for mute
control. The door lock button is assigned to
telephones in Program 39; the door lock
activation time is assigned in Program 771. This door lock control function is not
associated with the DDCB door lock control;
it is an addition to the DDCB door lock
control. If the External Page Relay is selected, Background Music over external page
will be muted when an external page is
being delivered.
NOTE:
See LEDs 01 and 02 for DK8 KSU or DK16
Base Key Service Unit relay options.
• DK8 KSU or DK16 Base Key Service Unit
Relay, LEDs 02 and 01—The DK8 and
DK16 Base Key Service Unit has a relay
which can be configured for one of three
options: It can be configured to activate a
Music-on-Hold source when calls are placed
on hold, to mute Background Music (BGM)
when an external page is being made, or to
control an external answering machine or
external ringing device while the system is in
the NIGHT mode. Select one of the options
with the following LED settings.
• For the External Page option: LED 02
must be OFF. (It does not matter whether
LED 01 is ON or OFF.)
• For the Music-on-Hold activation option:
LEDs 01 and 02 must be ON.
NOTE:
See LEDs 01 and 02 for Base Key Service
Unit relay options.
• NT Relay Mode Assignment, LED 06—A
relay in the DK8 KSU or DK16 Base Key
Service Unit or on the PIOU or PIOUS can
be assigned to operate in one of two Night
Transfer modes. Before setting the specific
Night Transfer mode with LED 06, activate
the NT Relay in the DK8 KSU or DK16 Base
Unit with LED 01 or activate the NT Relay on
the DK16 PIOU or PIOUS with LED 05.
2-20
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
• For the NIGHT Relay Mode option: LED
the Base Key Service Unit, one from a
DDCB connected to a PDKU or KCDU in the
Expansion Unit, and one from a PIOU or
PIOUS in the Expansion Unit.
01 must be OFF and LED 02 must be
ON. (See LED 06 to specify how the
relay will operate when selected for this
option.)
Program 78—CO Line Special Ringing Assignments:
• Ring Over External Page During Night
Mode, Feature 1—This program selects
which CO lines will activate ringing over
external paging facilities during the NIGHT
mode.
• DISA CO Line Assignment, Feature 2—
This program assigns CO lines to be used
with the Direct Inward System Access
(DISA). CO lines may be set for DISA operation during the different system modes of
DAY, DAY2, and NIGHT. A CO line will
switch to normal ringing after ten seconds if
the outside caller does not use the DISA
feature. Normal function of these lines occurs for outgoing calls.
NOTE:
See LEDs 05 and 07 for DK16 PIOU and
PIOUS relay options.
Program 77-2—Door Phone Busy/Door
Lock Assignments:
• Door Phone Ring Count, LED 20—The
number of times that a door phone will ring
digital and electronic telephones is set with
this LED. Light the LED for one ring; turn off
the LED for five rings. The default is five
rings. See Program 79 to assign which
digital and electronic telephones will be rung
by door phones. Door phones will not ring
standard telephones.
• Door Phone Busy Out, LEDs 01,02, 03,
05, 06, 07—Each Door Phone/Lock Control
Unit (DDCB) can interface with up to three
door phones. The system treats each DDCB
as a station. Therefore, this is different from
station arrangements using telephones. The
system does not automatically know how
many door phones are connected to each
DDCB; so it must be told. This program is
used to enter that information so that a caller
will receive fast busy tone if the called door
phone does not exist. Door phones 1A, 1B,
1C are numbered 551, 552, 553, respectively, and are connected to the DDCB at
Port 02/DK8 or Port 04/DK16. Door phones
2A, 2B, 2C are numbered 554, 555, 556,
respectively, and are connected to the DDCB
at Port 03/DK8 or Port 12/DK16.
• Door Lock Assignments, LEDs 04 and
08—Each DDCB B-jack output can be configured as a door lock control. Door lock
control buttons for DDCB door locks are
assigned to digital or electronic telephones
in Program 39. Door lock activation time is
set in Program 77-1. The DK8 supports two
door lock (DDCBs) controls, and the DK16
provides a maximum of three door lock
controls—one from a DDCB connected to
NOTE:
An optional security code for DISA outgoing
CO calls is available via Program 60-6.
• Ring IMDU Maintenance Modem, Feature
5 (for STRATA DK16 only)—Remote Maintenance via the optional PIOU or PIOUS
IMDU modem can be accomplished with
this program. Different alternatives are available for the system modes of DAY, DAY2,
and NIGHT. If none of these are selected,
the IMDU can still be reached on station 619
with the DISA feature or by a Ring Transfer
from the DSS console attendant or any other
station. IMDU station 619 must be enabled
with Program 77-1.Program 79—Door
Phone Ringing:
• Muted Ring to Busy Electronic and Digital Telephone, LED 20—If all digital and
electronic telephones are busy and a door
phone button is pressed, a muted ring tone
can be sent to selected digital and electronic
telephones defined in this program. (Only
the lowest port in the appropriate ringing
group will mute ring.)
• Door Phone Ring, LEDs 01 ~ 06—When a
door phone button is pressed, selected digi-
2-21
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
tal and/or electronic telephones assigned in
this program will ring. See Program 77-2 for
a description of the door phone A, B, and C
numbering scheme. Door phones will not
ring standard telephones.
Program 80—Digital and Electronic Telephone
Ringing Tones: Distinctive system ringing sends
a different ring tone for CO line ringing than that
for intercom ringing. In addition, CO line ringing
at digital and electronic telephones can be different from one phone to another. Two choices
are available; one is 500 Hz modulated with 640
Hz (PERCEPTION ring tone), while the other is
600 Hz modulated with 800 Hz (STRATA ring
tone). Two digital or electronic telephones that
are close in proximity can then have distinctive
CO line ringing, as chosen with this program.
Programs 81 ~ 89—CO Line/Station Ringing
Assignments: A number of CO line-to-station
ringing patterns can be programmed into the
system. Nine categories exist, which are DAY
IMMEDIATE, DAY DELAY 1, DAY DELAY 2,
DAY2 IMMEDIATE, DAY2 DELAY 1, DAY2
DELAY 2, NIGHT IMMEDIATE, NIGHT DELAY
1, and NIGHT DELAY 2. DAY, DAY2 and NIGHT
refer to the three modes of the Night Transfer
button. DELAY 1 is a 12-second delay of ringing
signal to a digital or electronic telephone, and
DELAY 2 is a 24-second delay of ringing. The
delay functions are mainly used in CENTREX
applications but can be used for other situations. If delayed ringing occurs, the station that
initially rings will continue to ring with subsequent delayed-ring stations.
Program 93—CO Line Identification: This provides alphanumeric names (to appear on LCD
telephones) to CO lines, such as "WATS BAND
5," "FX TO NY," "MR JONES," etc. The names
may be up to 16 alphanumeric characters each
and display when the CO line is being used by
an LCD station.
Program 97—Printing Program Data Through
Station Message Detail Recording (SMDR):
Contents of each program can be sent to the
SMDR port for a hard copy printout.
Setting Date, Time and Day: The current date,
time, and day of the week can be set from any
LCD digital or electronic telephone connected to
Port 00.
2 TOLL RESTRICTION
2.01 The following provides the programmer with
an overview of the Toll Restriction feature and
step-by-step instructions to fill in the Toll Restriction System Record Sheets.
3 TOLL RESTRICTION OVERVIEW
3.00 Toll Restriction Methods
3.01 Toll Restriction screens and selectively restricts outgoing calls using three different methods. Each type of restriction can be programmed
for individual stations. Toll Restriction can also be
enabled/disabled for each outgoing CO line in the
system.
3.02 Simple Toll Restriction: The first method,
Simple Toll Restriction, only involves the first digit
dialed. The system can be programmed to reject
outgoing calls beginning with 0 or 1 (see Program
48).
3.03 Three-digit Toll Restriction: The second
method, Three-digit Toll Restriction, involves the
system analyzing the area code dialed, and selectively allowing/disallowing outgoing calls following
the criteria defined in Area Code Tables 1 ~ 4 (see
Program 46, codes 2 ~ 4).
3.04 Six-digit Toll Restriction: The third method,
Six-digit Toll Restriction, involves the system analyzing the area code and the office code, and
selectively allowing/disallowing outgoing calls following the criteria defined in Area Code Tables 1
~ 4 and Office Code Tables 1 ~ 4 (see Program 46,
codes 2 ~ 4 and 6 ~ 8).
NOTE:
Standard telephones should always be forced
to use Least Cost Routing to place outside
calls. This prevents Toll Restriction defeat
when the QRCU/K4RCU times out.
3.10 Toll Restriction Features
3.11 For description purposes, Toll Restriction is
divided into several components, or sub-features.
The sub-features operate independently of the
restriction methods just described, although they
may employ these methods.
2-22
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
3.12 Station Priority Classes 1 ~ 4: Four classes
of Toll Restriction can be defined to assign different levels of priority to individual stations. Classes
can be defined so each is progressively more
restrictive by allowing or denying specific area or
office codes, calls to long distance information,
international calls, and operator assisted calls
(Programs 46-10 ~ 40).
4 COMPLETING THE TOLL
RESTRICTION SYSTEM RECORD
4.01 The following instructions explain how to
complete System Record Sheets used to program
the Toll Restriction feature. They are arranged in
the same order in which the tables appear in the
Toll Restriction System Record Sheets. The following instructions are intended to give a concise
general definition of the programming characteristics defined by each record sheet.
3.13 Office Code Exception Tables: Class 1 ~ 4
restrictions can be further modified by defining as
many as eight exception tables to allow or deny
access to specific office codes that fall within
previously restricted area codes (Program 47).
Exception office code access is accomplished with
the Six-digit Toll Restriction method described
earlier.
NOTES:
1. On each record sheet, mark an X in the
space provided to indicate that a choice is
selected. Unless otherwise specified, this
indicates the LED is lit. When appropriate, indicate digits to be entered using the
station dialpad.
2. Initialized data and considerations are
documented when applicable.
3.14 Emergency, Information, and Toll-free
Long Distance Toll Restriction Override: Toll
restricted stations may be allowed to dial special
codes such as 911 for emergency response, 1-411
or 411 for information, or 800 prefix toll-free calls
(Program 46).
4.10 Program 44B—Toll Restriction/Traveling
Class Override Codes
4.11 Each of the four Toll Restriction classes
established in Program 46 can be assigned a
code with this program. If one of these codes is
entered at a station, the station will assume the
code’s class for that call. When the call is complete, the station returns to its regular class assigned in Program 48. The traveling class code
data is not sent out the SMDR port and will not print
out on station call records.
IMPORTANT!
Always be sure to provide access to emergency numbers such as 911.
3.15 Toll Restriction Override by System Speed
Dial: System Speed Dial numbers can be programmed to override Toll Restriction (see Basic
System Features, Program 10-1).
3.16 Toll Restriction/Traveling Class Override
Codes: Up to two Toll Restriction Override Codes
can be defined. When dialed at a Toll Restricted
station, these codes enable the station user to
override Toll Restrictions defined at the station
(Program 44B or 45-8 ~ 9). Codes may be changed
by stations chosen in programming (see Basic
System Features, Program 30).
4.20 Program 45-1—Toll Restriction Dial Plan
3.17 Special Common Carrier Authorization:
Toll Restriction can be programmed to recognize
Other Common Carrier (OCC) telephone numbers, directory numbers, authorization codes, and
PBX access codes. The system starts inspecting
numbers for Toll Restriction purposes after the
recognizable code is dialed (Program 45-3 ~ 6).
4.21 A dial plan must be defined for the Toll
Restriction software to recognize the typical dialing sequence of long distance/local calls made
from the system’s home area code and to identify
area and office codes. The dialing plan defines
several components of a telephone number for
long distance calling:
NOTE:
Stations selected in Program 30, LED 16
ON, can add, change, or delete the codes set
in Program 44B. See Program 30 for more
information regarding station revision of override codes.
2-23
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
• Long Distance Prefix 1—In most areas, a 1
must be the first digit dialed for long distance
calling. In such areas, the area code is dialed
right away. The dial plan defines whether the
prefix 1 is required for a particular installation’s
long distance calling.
• Area/Office Code Numbering Schemes—In
most places, the middle digit of an area code is
0 or 1, and the middle digit of an office code is 2
~ 9. Toll Restriction examines the first three-digit
sequence dialed and determines whether it is
an area code or an office code.
§ If the middle digit is 0 or 1, then the sequence
is an area code.
§ If the middle digit does not equal 0 or 1, then
the sequence is an office code, and the
office code parameters of the selected dialing plan apply.
•
•
4.22 An exception to this rule exists. In some
places, area and office codes are interchangeable. The middle digit is always 0 or 1 (see Code
3 selection). In such a case, the system only knows
that three digits dialed are an area code if 1 is
dialed before them. If 1 is not dialed first, the
system knows the three digits are an office code.
The dial plan defines the numbering scheme applicable to the installation site.
• Office Codes: Office Code elements are defined as follows:
§ N=2~9
§ X=0~9
§ NXX = interchangeable with area code; 2nd
digit may be 0 or 1.
§ NNX = not interchangeable with area code;
2nd digit may not be 0 or 1.
•
•
4.23 Equal Access Codes and Special Common
Carrier Authorization Codes may be entered as
exceptions to the dialing plan in Program 45-3 ~ 6.
4.24 Selections: On the record sheet for Program 45-1, choose one of the following dial plans
by marking an X in the space next to the code.
• Plan 1 for dialing plan AC+NXX/1+NNX should
be selected if the installation is in a location
where a user places a long distance call to a
destination outside the area code without dialing 1 before dialing the area code. The user
places a long distance call to a destination in the
•
2-24
same area code by dialing 1 directly before the
office code.
When using this plan, the system recognizes
the following:
§ The first three digits of a ten-digit number is
an area code if the middle digit is 0 or 1.
§ The first three digits dialed immediately after
a 1 in an eight-digit string is an interchangeable office code (the middle digit may be 0 or
1).
§ A seven-digit string starting with an office
code is a local call.
§ An 11-digit string is not recognized.
Plan 2 for dialing plan 1+AC+NXX/1+NNX
should be selected if the installation is in a
location where a user places a long distance call
to a destination outside the area code by dialing
a 1 before dialing the area code. The user
places a long distance call to a destination in the
same area code by dialing a 1 directly before the
office code.
When using this plan, the system recognizes
the following:
§ The first three digits following a 1 in an 11digit number are an area code, if the middle
digit is 0 or 1.
§ The first three digits dialed immediately after
a 1 in an eight-digit string is an interchangeable office code (the middle digit may be 0 or
1).
§ Digits 5 ~ 7 in an 11-digit string may be an
interchangeable office code as well.
Plan 3 for dialing plan 1+AC+NXX/NNX should
be selected if the installation is in a location
where a user places a long distance call to a
destination outside the area code by dialing a 1
before dialing the area code. The user places a
long distance call to a destination in the same
area code by simply dialing the number, without
a 1 in front. The area and office codes may be
interchangeable. The system differentiates between them whenever it sees the digit 1 dialed.
When using this plan, the system recognizes
the following:
§ If 1 is the first number dialed in an 11-digit
string, the next three digits are an area code.
§ A ten-digit string is not recognized.
§ The first three digits in a seven-digit string
are an office code. (There is no distinction
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
4.44 Items 3 and 5: Enter the first five digits of the
SPCC telephone number in the spaces labeled
SPCC1 Telephone Number (item 3) or SPCC2
Telephone Number (item 5) on the record sheet.
The initialized state assigns “00000” to items 3 and
5.
between local call dialing and long distance
dialing within the area code.)
§ Digits 5 ~ 7 in an 11-digit string may be an
interchangeable office code as well.
• Plans 4 and 5 are not used in the United States.
NOTE:
Program 45-1 must be completed for the
Least Cost Routing (LCR) feature to function
properly. See LCR Program 50-1.
4.45 Items 4 and 6: Enter each SPCC’s authorization code digit length. The number of digits
allowed (including the first five specified in items 3
and 5) ranges from 00 ~ 99. Initialized data assigns
“00” to items 4 and 6. Enter two digits on the record
sheet.
4.30 Program 45-2—Toll Restriction Disable
4.31 Selected CO lines may be programmed to be
exempt from any Toll Restrictions defined in this
section. Mark the exempt CO lines with an X on the
record sheet. Initialized data leaves all LEDs OFF,
which causes all CO lines to be affected by Toll
Restrictions defined.
4.46 A restricted station is not able to place a toll
call through a long distance carrier by dialing the
SPCC1 or SPCC2 telephone number if the station
is denied from that number in other toll restriction
programs. Upon recognizing the first five digits
dialed, Toll Restriction software is notified to allow
the number of digits programmed in items 4 or 6
(00 ~ 99, including the first five dialed as SPCC1 or
2).
NOTE:
Toll Restrictions disabled in this program
override station Toll Restrictions defined in
Program 48.
4.47 The system interprets data to be a sevendigit local call to an SPCC. Only five digits of the
seven-digit number are entered; therefore, the last
two digits are don’t care digits. Any number dialed
that has the same first five digits as the carrier, the
system will assume the SPCC is being called.
4.40 Program 45-3 ~ 6—Equal Access/Special
Common Carrier Numbers and Authorization
Code Digit Length
4.41 The purpose of this program is to notify the
system of how many digits to ignore before it
applies Toll Restriction. This enables the system to
allow the use of Special Common Carrier authorization (SPCC) codes.
IMPORTANT NOTE!
For items 4 and 6, do not enter more digits
than necessary for the authorization code.
If too many digits are allowed, Toll Restrictions may be ignored.
4.42 SPCC telephone numbers may be defined to
notify the system to modify restrictions when the
station user is dialing a long distance carrier. The
user dials a code to access the carriers. Original
restrictions re-activate after the carrier number is
dialed.
4.50 Program 45-8 ~ 9—Toll Restriction
Override Code
4.51 Two different codes may be dialed by any
station user to override station-specific restrictions.
4.43 There are two elements Toll Restriction software must verify for a user to successfully complete long distance calling:
• The first five digits of the number dialed to
access the long distance SPCC.
• The total number of digits belonging to the
authorization code of the SPCC.
4.52 Fill in the codes on the record sheet. They
must be four digits each.
4.53 Selected stations in the system are able to
alter the override codes. These stations are assigned in Program 30. To change the codes from
selected stations:
2-25
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
Code 1: Intercom + 6 5 4 + code + Redial
Code 2: Intercom + 6 5 5 + code + Redial
4.80 Program 46-10 ~ 40—Toll Restriction Class
Parameters (Classes 1 ~ 4)
4.60 Program 46-2 ~ 4—Toll Restriction
Allowed/Denied Area Codes Assigned by
Class
4.81 This program defines parameters of each
Toll Restriction class, including dialing plan restrictions and exceptions to previous restrictions.
4.61 Four Toll Restriction classes can be defined
for the system. Each class area code provides for
a different combination of restrictions.
4.82 Toll Restriction exceptions and dialing plan
restrictions may be defined for each class. Program 46-10 assigns class 1 restriction exceptions
and parameters; 46-20 assigns class 2; 46-30
assigns class 3; 46-40 assigns class 4. This program also relates to Program 47. See Program
47 for more explanation.
4.62 This program defines the area codes allowed or denied for each Toll Restriction class.
Area code tables for classes 1 ~ 4 can each
describe area codes that are allowed or denied for
the class. The tables (in memory) operate as allow
tables. If an area code exists in a table (displays
with 4 #), then it is allowed. Anything not displaying
is not allowed. Initialized data allows all area codes
for each class (all codes are in all tables). All
allowed area codes can be displayed (4 #) for each
class.
4.83 To define the proper parameters for a Toll
Restriction class, make the appropriate selections
on the record sheet designated for classes 1 ~ 4:
• LED 01: 0 Restricted—Mark an X next to LED
01 if operator or operator-assisted calls are
restricted for the class being defined.
IMPORTANT NOTE!
To allow 0 + dialing (LED 01 must be OFF),
codes 020 ~ 099 must be allowed in Program 46, and digit free must be allowed in
Program 48. Warning—Allowing 0 + dialing also allows operator-assisted toll calls.
4.63 For each class, choose whether the record
table is used to record allowed area codes in
memory (ALLOWED) or denied area codes not in
memory (DENIED). Enter the area codes that
define the set.
• LED 02: 01 Restricted—Mark an X next to LED
4.70 Program 46-6 ~ 8—Toll Restriction Allowed/Denied Office Codes Assigned by Class
02 if overseas operator or unassisted overseas
operator calls are restricted for the class being
defined.
• LED 03: 1+AC+555 and AC+555 Allowed—
Mark an X next to LED 03 to allow the particular
class to call all restricted area codes plus the
office code of 555, including out-of-area directory assistance calls. Turning the LED OFF
does not necessarily deny information calls.
This may also be accomplished in the office
code table and/or the area/office code exception tables.
• LEDs 11 ~ 18: Area Code/Office Code Exception Tables 1 ~ 8—Select the exception tables
that apply to the class being defined by marking
an X in the box. Exception tables for both area
and office codes will be defined in Program 47.
4.71 This program defines the office codes allowed or denied for each Toll Restriction Class
within the home area code. Office code tables for
classes 1 ~ 4 can each describe office codes
allowed or denied for the class. The tables (in
memory) operate as allow tables. If an office code
exists in a table (displays with 8 #), then it is
allowed. Anything not displaying is not allowed.
Initialized data allows all office codes in the home
area code for each class. 4.72 For each class,
choose whether the record table is used to record
allowed office codes in memory (ALLOWED) or
denied office codes not in memory (DENIED).
Enter the office codes that define the set.
2-26
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
NOTE:
Each class can be assigned any or all of the
eight available office code exception tables.
4.103 Station Restrict Code: The second feature assigns Toll Restriction to individual station
ports, in addition to previous restrictions. It includes seven different choices. One of the choices
must be entered for each port. Initialized data
assigns 0 or no restrictions to all ports. The seven
choices are explained as follows.
4.90 Program 47—Toll Restriction Exception
Office Codes Assigned by Area Codes (Table
1 ~ 8)
4.91 This program defines exceptions to previously defined office code restrictions for up to eight
area codes, allowing six-digit Toll Restriction. Office codes entered in Tables 1 ~ 8 are opposite of
what is defined for the area code by Program 462 ~ 8. For instance, if Program 46 denies area
code 714, entering office codes 530 and 555 into
an exception table for area code 714 will allow
those office codes.
NOTE:
Station restrictions are overridden by CO
lines disabled as defined in Program 45-2. If
a station port has appearance of a CO line
with restrictions disabled, the restrictions will
be removed from the station on an individual
CO line basis through Program 45-2.
• 0: No Station Toll Restriction—Enter 0 in the
4.92 Eight exception tables are available. Each
area code with exception office codes requires a
table. Each table may hold up to 800 exception
office codes.
•
4.93 Enter the area code and required office codes
on the record sheet.
•
4.100 Program 48—Station Toll Restriction
Classification
4.101 This program assigns a combination of two
restrictions to each station port defined in the
system. The first feature is Digit Restriction and the
second is Station Restriction Assignment.
4.102 Digit Restrict Code: If Digit Restrict is
enabled for a particular station, the station is able
to dial the number of digits defined in the Program
45-1 Toll Restriction dialing plan.
• 1: Enable Digit Restriction—Enter 1 in the
Digit Restrict Code column, next to the port
number to enable the restriction for the station.
This is used to prevent a user from dialing a
second call when dial tone is returned from a CO
after the outside party disconnects.
• 2: Disable Digit Restriction—Enter 0 in the
Digit Restrict Code column, next to the port
number to disable digit restriction for the station.
This allows Toll Restricted users to dial any
number of digits (i.e., to an external voice mail
device, computer, etc.).
•
•
2-27
Station Restrict Code column, next to the port
number, to remove Toll Restrictions from the
station.
1: Area Code Toll Restriction—Enter 1 in the
Station Restrict Code column, next to the port
number, if the selected station must be restricted from dialing all area codes.
2: Area Code Toll Restriction and “0” or “1”
as a 1st or 2nd Digit—Enter 2 in the Station
Restrict Code column, in the space available for
the port number, if the selected station must be
restricted from dialing all area codes, and 0 or 1
when used as a first or second digit. This
restriction prevents the station from making any
long distance calls or operator-assisted calls, in
addition to outgoing calls outside the home area
code. In applicable areas, this prevents long
distance office codes from being dialed (if
1+NNX).
3: Class 1 Toll Restriction—Enter 3 in the
Station Restrict Code column, in the space
provided for the port number, if the selected
station will be assigned to the Class 1 level of
restriction. Class 1 area and office code restrictions are defined in Program 46 and exception
office code tables in 46-10.
4: Class 2 Toll Restriction—Enter 4 in the
Station Restrict Code column, in the space
provided for the port number, if the selected
station will be assigned to the Class 2 level of
restriction. Class 2 area and office code restrictions are defined in Program 46 and exception
office code tables in 46-20.
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
• 5: Class 3 Toll Restriction—Enter 5 in the
Station Restrict Code column, in the space
provided for the port number, if the selected
station will be assigned to the Class 3 level of
restriction. Class 3 area and office code restrictions are defined in Program 46 and exception
office code tables in 46-30.
• 6: Class 4 Toll Restriction—Enter 6 in the
Station Restrict Code column, in the space
provided for the port number, if the selected
station will be assigned to the Class 4 level of
restriction. Class 4 area and office code restrictions are defined in Program 46 and exception
office code tables in 46-40.
6.03 LCR Home Area Code. Notifies LCR software of the area code of the installation site.
6.04 LCR Special Codes. Notifies LCR of special
emergency and operator codes that will be automatically routed as a local call, without unnecessary delay.
6.05 Long Distance Information Plan Number.
Notifies LCR software how to route a long distance
information call.
6.06 Local Call Plan Number. Notifies LCR software which call routing plan is specifically designed to handle local and special calls.
5 LEAST COST ROUTING (LCR)
5.01 The following provides the programmer an
overview of the LCR feature and step-by-step
instructions to fill in the LCR System Record Sheets.
6.07 LCR Timeout after 0 (Zero) is Dialed. Notifies the system of the time delay to the user after
dialing a 0, before a regular operator is accessed.
6 LEAST COST ROUTING (LCR)
OVERVIEW
6.08 LCR Area Codes. As many as eight separate area code tables can be defined; one for each
available call routing plan. Each table defines the
area codes that are handled by the particular
routing plan.
6.00 Definition
6.01 The LCR feature enables the system to automatically route each outgoing voice and data call
over common carriers and selected CO lines. The
customer chooses these lines for the specific time
of day and for system users with varying priorities.
If the system is programmed properly, LCR can
select the most economical route, helping save
money. If the best routes are unavailable, users
with priority can access more expensive outgoing
routes. Figure 2-1 shows a block diagram of LCR
operation. Several elements of LCR must be defined in programming.
6.09 LCR Office Code Exceptions for Area
Codes. As many as eight LCR office code exception tables may be defined to inform LCR software
how to handle specific office codes within area
codes. According to the tables defined, specific
exception office codes can be routed through a
different call plan than the overall area code plan.
6.10 LCR Schedule Assignments. Call routing
plans 1 ~ 8 can send the outgoing calls of different
groups of stations according to a time schedule,
and call route definitions.
NOTE:
For LCR to function properly, CO line groups
must be created in Program 16; CO line
restrictions set in Programs 40 and 41; and
the area dialing plan assigned in Program
45-1.
6.11 LCR Route Definitions. Groups of CO lines
assigned to special common carriers, foreign exchange lines, or other special services can be
specified as call routes.
6.02 LCR General Parameters. Enables
features including a warning tone for last choice
route number, a comfort dial tone during LCR
processing, and the Long Distance Information
dialing plan.
2-28
6.12 LCR Modified Digit Assignments. Carrier
codes can be programmed to dial automatically
when a call is placed over the appropriate route.
Digits can be added to the front or back of special
common carrier codes or other access numbers to
make placing calls an invisible process for the
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
User dials 9.
User dials telephone number (see note).
System analyzes telephone number, and
checks it against most Program 50 options.
• LCR Parameters (50-1)
• LCR Special Codes (50-31 ~ 35)
• LCR Long Distance Information Plan
Number (50-4)
• LCR Local Call Plan Number (50-5)
• LCR Dial Zero Time Out (50-6)
Does system
find a match?
NOTE:
If the telephone number is restricted by system
Toll Restriction, the caller will receive busy tone
and LCR will be cancelled immediately.
Routes call per the local LCR plan
specified in 50-5 or per long distance
information LCR plan specified per 50-4.
YES
System checks the time of day. (This must
be set properly by station port 00.)
NO
Selects the appropriate schedule (1, 2 or 3)
for the time as specified in Program 53.
System searches all office code exception
tables entered into LCR plans 1 ~ 8 with
Program 52.
Does system
find a match?
YES
Routes call per the plan cross referenced
by the LCR office code exception table that
contains the match (52-X0; X = 1-8).
Determines the station's group assignment
as specified in Program 56. Within the
Time of Day Schedule, an LCR station
group is matched to group 1, 2, 3 or 4.
NO
System checks the number to see
if it is an area code or an office code.
Is number
an office
code?
System assumes home area code and
routes call per the LCR plan containing
the home area code (Program 51).
YES
NO
Verifies the CO line access, as defined by
Program 40. Within a CO line group, the
system checks to see if access is allowed
to lines chosen in selected route definition.
System checks all area code
tables entered into the LCR plans
1 ~ 8 through Program 51.
Routes call per the
applicable LCR plan.
Does system
find a match?
Selects the route definition as defined
by Program 54 for the CO line group
(Program 16), and activates the modified
digits table instructions defined through
Program 55.
The system selects the first available route
definition (1st, 2nd, 3rd or 4th choice) that
represents both CO line group and modified
digits table.
Does the
CO line have
access?
YES
NO
STOP.
Call not
completed.
YES
NO
System selects a CO line and dials number.
Call
not
completed.
CALL COMPLETED
FIGURE 2-1
LCR OPERATIONAL BLOCK DIAGRAM
2-29
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
user. Digits may also be deleted from the front of
the dialed number.
7 COMPLETING THE LEAST COST (LCR)
ROUTING SYSTEM RECORD
6.13 LCR Station Access Priority Assignments. Each station port defined in the system
may be assigned to one of four station priority
groups. The groups can have varying access to
the defined call routes at different times of day.
Each group is partitioned from the other groups.
NOTE:
All stations using LCR should be ALLOWED
CO line access in Program 40, and DENIED CO line access in Program 41.
7.01 The following instructions explain completion of the System Record Sheets used to program LCR. Instructions are arranged in the same
order as data tables in the Least Cost Routing
System Record. The instructions are intended to
give a concise, general definition of LCR characteristics defined by each record sheet.
6.20 Conditions
6.21 A number of conditions apply to LCR assignments. A summary of each is listed here.
Paragraph 7, Completing the Least Cost Routing Record Sheets, gives more detailed explanations and examples of how the conditions
relate to the programming process.
NOTES:
1. On each record sheet, enter required
data in the space provided to make a
selection, unless otherwise specified.
2. The initialized state and considerations
are documented on the record sheet.
6.22 If a station has direct CO appearances or
pooled CO line buttons programmed to allow
direct outgoing line access, LCR will be bypassed using the pooled line or a CO line button.
7.10 LCR CO Line Programming Reference
Chart
6.23 LCR accommodates special code dialing,
such as 911 for emergency response, 1-411 or
411 for information, or 800 area code toll-free
numbers. These calls can be directed to the
local call route. Examples are given in Paragraph 4 (see Program 50-31 ~ 35).
7.11 This chart is intended for reference only.
Information relevant to LCR is compiled here
from Basic System Programming.
1) Under the column labeled “CO Lines in
Group (01 ~ 08),” enter the numbers of the
CO lines assigned to groups 81 ~ 84 (for
STRATA DK8) or 81 ~ 88 (for STRATA
DK16). Refer to the completed record sheet
in Program 16 for this information.
IMPORTANT NOTE!
Always provide emergency service access for numbers such as 911.
6.24 Basic System Record programs related to
LCR include:
• Program 16 defines which outgoing CO lines
are assigned to CO line groups 81 ~ 88.
• Program 40 denies a station complete CO
line access. This also applies to LCR.
• Program 41 restricts outgoing CO line calls to
selected stations. These stations may make
outgoing calls through LCR.
2) Under the column labeled “CO Line Type/
Comments,” enter the service type, the
common carrier name, or the line type for
each line group, e.g., local line, Foreign
Exchange (FX) to 818 (LA), WATS (out of
state), etc.
6.25 Standard telephones that are Toll Restricted
should be required to use LCR to place outgoing
calls. This prevents Toll Restriction defeat when
the QRCU (in DK8) or K4RCU (in DK16) times out.
2-30
3) Refer to Basic System Record, Program
40, to restrict stations from incoming and
outgoing access of CO lines, including using LCR. All stations that must use LCR to
make outgoing calls must NOT be restricted
in this program. These restrictions do apply
to LCR.
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
sive route is typically programmed to be the
least desirable. A user has three choices upon
hearing the warning tone:
a) Ignore the tone, LCR places the call using
the least desirable route.
b) Hang up and try later to save money.
c) Activate the Automatic Call Back feature.
The appropriate CO line group calls the user
back when a more desirable route number
becomes available.
• OFF: No warning tone sounds.
4) Refer to Basic System Record, Program 41,
to restrict stations from accessing outgoing
CO lines, except through LCR. All stations
that must use LCR for outgoing calls must be
restricted from CO line access in this program.
7.20 Program 50 Series—LCR Definitions
7.21 Program 50-1—LCR Parameters. This program defines general operating parameters for
LCR software.
7.22 Program 50-2—LCR Home Area Code.
Enter the local area code in the spaces provided on
the record sheet. Initialized data leaves the home
area code blank.
• LCR matches the area code entered here with
the LCR route plan containing the home area
code in its Area Code Table. (The home area
code is later entered into one of the eight available LCR route plans through Program 51.)
Thus, LCR is informed of how to handle local
calls.
• Typically, systems are configured to have the
LCR route plan containing the home area code
as the same as the local route plan defined in
Program 50-5. This is typically programmed by
the installer to be route plan number 1, rather
than the default plan 8.
NOTE:
Mark an X in the column to indicate which
programming button LEDs should be lit. Initialized data leaves all LEDs OFF.
LED 01
• ON: LCR software is enabled system-wide.
• OFF: LCR software is disabled. None of the
LCR programming referred to by this section is
recognized. Dial 9 access assigned in Program
16 is enabled.
LED 02
• Not used.
LED 03
• ON: LCR routes long distance information (LDI)
calls over the plan number specified in Program
50-4.
• OFF: LCR routes LDI calls using area codes
specified in route plans 1 ~ 8, as it would for any
other call.
7.23 Programs 50-31 ~ 35—LCR Special Codes.
Five Special Codes may be entered in spaces
provided next to 31 ~ 35. The codes may be a
maximum of four digits, and should include items
such as 911 for emergency calls and 411 or 1-411
for local information, etc. Initialized data leaves all
codes blank.
• When any of these codes are dialed, LCR is
flagged to treat the call as follows:
§ The call will be sent over the local call route
plan specified in Program 50-5.
§ No additional digits need to be dialed. They
are not necessary. Therefore, the call is put
through immediately.
LED 04
• ON: Station users hear a simulated dial tone
immediately after dialing the access LCR code
(typically 9), until the first digit of the phone
number is dialed. The dial tone is simulated to
assure the user of the system’s proper operation, but it is not a functional dial tone.
• OFF: Station users hear nothing after dialing the
LCR access code until the destination rings or
issues a busy signal.
7.24 Program 50-4—LCR Long Distance Information (LDI) Plan Number. Enter the number of
the LCR route plan (1 ~ 8) over which long distance
information calls will be routed. Typically, long
distance information calls are routed over the local
call route defined in Program 50-5.
LED 05
• ON: The user is notified with a warning tone to
indicate that LCR has routed the call over the
least desirable route number. The most expen-
2-31
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
• If the long distance information plan is chosen in
area code calls are placed over which LCR Plan
Number (1 ~ 8). Initialized data assigns all
possible area codes (000 ~ 999) to LCR Plan 8.
Therefore, calls made to all area codes will be
routed over route definitions defined in Program 54 for plan 8, following the time schedule
specified by Program 53 for plan 8 (unless other
assignments are made in plans 1 ~ 7).
• For example, any area code entered in a Program 51 LCR area code table for plans 1 ~ 7 is
subtracted from plan 8. An area code cannot be
lost. If it is subsequently deleted from plans 1 ~
7, LCR software automatically adds it to plan 8.
• To fill in record sheets for plans 1 ~ 8:
§ Check the box by Area Code Table.
§ Enter the applicable area codes, three digits
per box.
Program 50-1, the call is routed as defined by
this table.
• Initialized data assigns plan 8 to be the LDI route
plan.
7.25 Program 50-5—LCR Local Call Route Plan
Number. Of the eight route plans available for
LCR call processing, one must be defined as the
Local Call Plan, typically route plan 1. Enter the
number of the plan (1 ~ 8) over which local calls,
operator-assisted/0+ calls, and special code calls
will be routed.
7.26 Program 50-6—LCR Dial 0 (Zero) Timeout. Enter the maximum number of seconds LCR
waits for a user to dial additional digits after a 0,
before it routes the call to an operator for assistance. LCR will wait this number of seconds to
receive additional digits that will indicate charge
calls, collect calls or other 0+ calls.
NOTE:
Remember that LCR matches the home area
code entered in Program 50-2 with the LCR
route plan containing the home area code in
its Area Code Table. The home area code
must be entered into one of the eight available LCR route plans through Program 51.
Thus, LCR is informed of how to handle local
calls. Typically, systems are configured to
have the LCR route plan containing the home
area code as the same as the local route plan
defined in Program 50-5. This usually is
programmed by the installer to be route plan
number 1, rather than the default plan 8.
• The allowed range is 04 ~ 10 seconds. Always
enter two digits. Initialized data assigns an LCR
dial zero time-out value of 06 seconds.
7.30 Route Plan Overview
7.31 Four groups of programs define eight separate LCR route plans. They are Programs 51 ~ 54.
The purpose of the plan scheme is to provide the
system with directions for routing all possible calls,
made by all possible users at all possible times of
day. Eight separate plans provide the customer
flexibility enough to route different area codes and
exception office codes over different CO line groups.
7.35 Program 52—LCR Office Code Exceptions for Specified Area Code. The purpose of
the Office Code Exception Table is to enable the
customer the flexibility of routing specific office
codes through a different call plan than other office
codes used with that area code.
• Eight LCR office code exception tables may be
defined for the overall LCR scheme. Any number of exception code tables may be assigned to
each route plan, although each exception table
may only be used once system-wide.
• Every route plan can be assigned to define a
set of area codes and office code exceptions
or a set of office code exceptions.
• This program applies to both examples listed
below. In the first case, an office code exception table does not need to be defined in
addition to the area codes in Program 51, but
7.32 Initialized data assigns all calls to plan eight.
Any assignments made in Programs 51 ~ 54 for
plans 1 ~ 7 will exempt the defined call from being
made on route plan 8. Likewise, any phone number not specified in routes 1 ~ 7 automatically
defaults to route plan 8.
7.33 Tables for Programs 51 ~ 54 appear on LCR
Route Plan Numbers 1 ~ 8. The following instructions reveal how to fill in individual tables within the
plans. Each of the following program tables must
be completed for all plans.
7.34 Program 51—LCR Area Code Tables. Every route plan can be assigned to define a set of
area codes and/or office codes.
• The purpose of Program 51 is to define which
2-32
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
1: Enter the same Schedule Start Times for
Schedules 1 and 2. Use military time, in the
format HH:MM (Hours:Minutes). Fill in all
four digits. Initialized data assigns “0000” to
all times.
• If LCR software sees schedules 1 and
2 have the same start times, then it
only looks at schedule 1 for route definitions.
2: Enter Route Definition Numbers for
Schedules 1 and 2. Four definitions may
be entered for each group.
• LCR Station (Class) Groups 1 ~ 4 are
assigned in Program 56.
• LCR Route Definition numbers 1 ~ 4
are defined in Program 54.
• The order in which the route definitions are entered defines the order of
LCR line selection. The most desirable route should be entered in the
leftmost position, and the least desirable route in the rightmost position.
• If “1” is assigned to Station Group 1
and 1 for route definition only, then
those assigned will only be able to use
route definition 1, thereby restricting
them during times that route definition
1 is not allowed.
• Keep in mind that the route definition
number is being entered, not the CO
line group number. The definitions are
assigned in Program 54.
it may. In the second case, the plan may only
pertain to exception office codes for certain
area codes.
Example 1—In the first example, office code
exception tables will be defined to the area
code table. Use the continuation sheet to
define the exception office codes. As many as
eight of the office code exception tables may
be linked to a plan, but each exception table
may only be used once. When using the
continuation sheet, be sure that the same
exception table is not assigned to more than
one plan.
• Turn to the continuation sheet (that follows plan 8 record sheet).
• Determine the plan number where the
exception office codes will be rooted.
• Fill in the area code of the exception office
codes in the spaces provided by the correct plan number. These office codes will
be routed differently than the overall area
code.
• Enter the specific office codes that are to
be routed differently.
Example 2—In the second example, the route
plan only applies to office code exceptions.
The first office code exception table may be
documented on the LCR Plan record sheet:
• Check the box on the record sheet next to
Office Code Exception Table number.
• Enter the number of the exception table (1
~ 8). Make sure this table number is not
entered on any other plan or on the continuation sheet.
• Enter the applicable area code.
• Enter the specific office codes that are to
be routed differently than the area code.
Installation requiring time scheduling feature—When an installation requires the time
scheduling feature to be programmed, three
“shifts” of route definitions can be assigned per
station group. To reflect this on the record sheet,
substitute Step 1 of the procedure described for
the typical customer with the following:
1: Enter the Schedule Start Times for Schedules 1, 2 and 3. Use military time, in the
format HH:MM (Hours:Minutes). Fill in all
four digits. Initialized data assigns “0000” to
all times.
• Start time for schedule 2 is the stop
time for schedule 1.
• Start time for schedule 3 is the stop
time for schedule 2.
• Start time for schedule 1 is the stop
time for schedule 3.
7.36 Program 53—LCR Schedule Assignments. This program assigns up to three time
schedules to each plan. Each time schedule
consists of four different route definition choices
(defined in Program 54) available to the four
station groups (defined in Program 56). It may
be helpful to complete Program 54 portions of
the plans and Program 56 before proceeding.
Typical installation without time scheduling
feature—In most cases, an installation will not
require use of the time schedule feature. To
reflect this on the record sheets for plans 1 ~ 8:
2-33
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
7.37 Program 54—LCR Route Definition: The
purpose of this program is to define four different
ways of routing calls for each of the eight LCR
plans. Define each route by selecting and entering:
1: CO Line Group (1 ~ 8): Refer to the LCR
CO Line Programming Reference Chart
completed at the beginning of the LCR
record sheets.
• Each CO line group represents a type
of service, e.g., special common carrier, foreign exchange, local line group,
etc.
• Program 16 assigns CO lines to CO
line groups 1 ~ 8 (81 ~ 88).
• Program 40 denies incoming and outgoing CO line access to stations, including LCR access.
• Program 41 allows CO line access to
stations using LCR only for outgoing
calls when enabled.
2: Modified Digits Table (1 ~ 6): Refer to
Programs 55-0, 55-1 and 55-2. The system handles CO line groups differently,
according to which modified digits table
was assigned in Program 54.
Digits Table. The maximum number is ten.
Always make the entry two digits.
7.44 Program 55-1—LCR Modified Digits-Add
to Front of Dialed Number. Enter the digits that
must be added to the front of the number dialed
in the Add Digits Table. The maximum quantity
of digits is 22, including pauses.
• Length of pause can be indicated by using
codes (P1 ~ P8) specified in the Pause Entry
Reference Table. Each pause takes two digits of memory space.
• Try to allow for the longest wait, e.g., make the
pause longer, rather than shorter, to accommodate the length of time a carrier may need
to access the service tones, etc.
7.45 Program 55-2—LCR Modified Digits-Add
to End of Dialed Number. Enter the digits that
must be added to the end of the number dialed
in the Add Digits Table. The maximum quantity
of digits is 22, including pauses.
• Length of pause can be indicated by using
codes (P1 ~ P8) specified in the Pause Entry
Reference Table. Each pause takes two digits of memory space.
• Try to allow for the longest wait, e.g., make the
pause longer, rather than shorter, to accommodate the length of time a carrier may need
to access the service tones, etc.
7.40 Program 55 Series—LCR Modified Digits Tables
7.41 This program defines six modified digits
tables for LCR call handling. Each modified
digits table assigns editing steps that include:
• Deleting a pre-defined quantity of digits from
the front of the number dialed (Program 550).
• Adding a pre-defined number to the front of
the number dialed (Program 55-1).
• Adding a pre-defined number to the end of the
number dialed (Program 55-2).
7.46 Program 56—LCR Station Group Assignment. The purpose of this program is to assign all
defined station ports to one of four LCR Station
Groups.
• Station groups are completely independent of
one another. Therefore, each station group must
be defined separately.
• Software does not automatically assign the highest, all-inclusive routing priority to class 1 stations, making all routes available to class 2, 3
and 4 stations available to class 1 as well.
• Instead, stations are assigned to independent
groups (partitioned). Completely flexible assignment of routing definitions to groups is allowed,
with no one group’s definition affecting another’s.
Each group’s route definitions are specified to
activate separately according to the time schedules set by Program 53.
7.42 The purpose of this program is to define
call handling so the route definition used by LCR
is invisible to the station user. The station user
handles all calls the same way. The goal is for
LCR to remember the dialing peculiarities of
each call route, so the user doesn’t need to
know.
7.43 Program 55-0—LCR Modified Digits-Delete. Enter the Quantity of Digits that should be
deleted from the front of the number dialed for
each of the six Table Numbers in the Delete
2-34
1: Enter the station group number next to the
port number.
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
SYSTEM RECORD SHEETS
2-35
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
IMPORTANT INITIAL INSTALLATION NOTES FOR STRATA DK8 AND DK16!
These minimum installation steps must be carried out for proper system operation.
1. Set the SW1 switch in the Base Unit ON for BATTERY OPERATION; otherwise, all programmed
customer data will be lost on power down.
2. If required, install KSTU and K4RCU in the DK16 Base Unit, or QCDUs, QSTU, QCNU,
QRCU, and QSMU in the DK8 KSU.
3. If the DK16 system is configured with an Expansion Unit, follow the order prescribed
below:
a) Install PDKU, PEKU, PSTU, PESU, or KCDU in Slot 04 of DK16 Expansion Unit.
b) If installing two KCDUs in DK16, install a KCDU in Slot 05. The only PCB allowed in
the Expansion Unit with a KCDU PCB is a second KCDU PCB (except for PIOU(S).
c) If the system is configured with a PCOU, install it in Slot 05 in DK16. (The system
cannot be configured with both a PCOU and KCDU in the Expansion Unit.)
d) If the system DK16 is configured with a PIOU or PIOUS, install it in Slot 06. (Slot 07
should be reserved for future use.)
4. Initialize Programs 00 ~ 97 by running Program 90 for DK8 and DK16.
5. Run Program 92-1, 2, 3, 4, 5, and 9 for DK8 and DK16.
6. For DK16 installation only, enter the hardware configuration with Program 03, exit the
programming mode, turn power OFF for five seconds, then turn power back ON.
Program 03 does not apply to DK8.
WHEN LATER ADDING DK16 KSU PCBs
1. Turn power off when installing PCBs, then turn power ON.
2. Install new PCBs and set the new configuration with Program 03. (Turn power OFF for
five seconds after running Program 03.)
3. Program new features, options, etc., created by new additions.
WHEN LATER ADDING DK8 KSU PCBs
1. Turn power off.
2. Install PCB(s).
3. Turn power on.
4. Program new features, options, etc., created by new additions.
2-36
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM NUMBER INDEX
FEATURE OR TOPIC
PROGRAM NO. FEATURE OR TOPIC
Account Codes
15, 30, 39, 60, 69, 70
Alarm Sensor Button (DK16 only)
39
All Call Voice Page
05, 10-2, 31, 39
Alternate Point Answer
10-1
Amplified Conference (DK16 )(External) 10-2, 10-3
Automatic Hold
35
Automatic Busy Redial
10-1, 16, 30, 39
Automatic Callback
05, 39, 10-2
Automatic Hold Recall
34
Automatic Preference
32
Automatic Release Hold/VM Port
15
Background Music
05, 10-2, 19, 39
Busy Calling/Called Station
35
Busy Override
05
Busy Tone Cadence Change
10-2
Busy Station (Trans/Ring)
35
Call Blocking (VM Ports)
31
Call Forwarding (all types)
10-2, 36, 39
Call Pickup
10-1, 15, 39
Call Transfer with Camp-on
10-1
Camp-on
10-1, 37
Centrex/PBX Compatible
42-0, 42-1 ~ 8
Centrex Ringing Repeat
10-1
CO/Centrex/PBX Feature Buttons 39, 42-0, 42-1 ~ 8
CO Line Access
39, 40, 41
CO Line Alpha Identification
93
CO Line Groups
16
CO Line Reseize Guard Time
10-1, 42-0
CO Line Queuing
05, 16
CO Line Ringing
78, 81 ~ 89
Conferencing
10-1, 15
Credit Card Calls (0 + dialing)
43, 60-7
Data Port/DIU Configuration
20, 21, 22, 39
DAY/NIGHT Mode
10-2, 78, 81 ~ 89
Delayed Ringing
82, 83, 85, 86, 88, 89
Digital Telephone
03, 30, 38, 92-5
Direct Inward System Access (DISA) 15, 10-1, 60, 78
Direct Station Selection
29-1 ~ 29-2, 39
Distinctive Station Ringing
10-2, 80
Do Not Disturb
05, 39
Do Not Disturb Override
05, 30
PROGRAM NO.
Door Lock Control
39, 77-1, 77-2
Door Phones
05, 77-1, 77-2, 79
DSS Console Features (DK16 only)
03, 28, 29-1 ~ 29-2, 10-2
DTMF and Dial Pulse Assignments 10-1, 2, 15, 30, 39
DTMF Receiver (QRCU/K4RCU) Operation 03, 12, 15
DTMF Signal Time, CO lines (80/160 ms)
10-1
DTMF Signal Time, VM Ports (80/160 ms)
10-2
DTMF Tone Return
10-2
Emergency Numbers
44A
Exclusive Hold
10-1
Executive Override
05, 10-2, 30
External Page Interface
10-2, 77-1, 78
Fixed Call Forwarding
36, 39
Flash Timing
12
Flexible Access Code Numbering
05
Flexible Button Assignments
38, 39
Flexible Intercom Numbering
04, 05, 39
Flexible Line Ringing Assignment
81 ~ 89
Flexible PCB Slot Configuration (DK16 only)
03
Forced/Voluntary Account Codes 15, 30, 44A, 60, 39
Group Paging
05, 31
Handsfree Answerback
10-3, 17, 31
Handsfree Answerback (No CFNA)
35
Hold/Park Recall Timing
34
Initialization (system programs)
90
Initialization (system/personal memory)
92
Intercom Access
39
Intercom Number Assignment
04
Least Cost Routing
16, 50 ~ 56
Liquid Crystal Display Features
10-2, 35, 39
Logical Ports
01, 02, 04
Message Center
13
Message Waiting/Flash
12, 35, 39
Microphone Control
10-3, 30, 39
Modem Pool Port Assignment
21
Music-on-Hold
77-1
Night Pickup Code
05
Night Ringing over External Page
15, 77-1, 78
Night Transfer
29, 39, 77-1, 78
Off-hook Call Announce
03, 30, 31
2-37
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM NUMBER INDEX (continued)
FEATURE OR TOPIC
PROGRAM NO. FEATURE OR TOPIC
On-hook Dialing
32
Outgoing Call Restriction
41, 44~48
Paging-Digital and Electronic Telephones
31, 39
Passwords-Remote Programming
00
Pause Timing
12, 39
PBX Access Code
42-1 ~ 42-8
PBX Backup
42-0
Physical Ports
01, 02, 04
Pooled CO Lines
16, 39
Pooled Line Buttons
16, 39
Port to Intercom Number Assignment
04
Privacy/Non-Privacy
31, 30, 39
Privacy Override
10-2, 30, 31
Private CO Lines
39
Redial Last Number
39
Relay Service
77-1
Remote Administration
and Maintenance
00, 77-1, 78
Repeat Last Number Dialed
30, 39
Ringing Line Preference
32, 81 ~ 89
Saved Number Redial
39
Security Code (DISA)
30, 60
Security Code (R. Maintenance)
00
PROGRAM NO.
Slot Assignment (DK16 only)
03
Speakerphone Assignment
30
Speed Dial Timeout
10-3
Speed Dial
10-1, 30, 39
Speed Dial Clear
92
Standard Telephone Ringing Options
10-2
Station Class of Service
30, 31, 35
Station Hunting (Data Calls)
22
Station Hunting (Voice Calls)
33
Station Message Detail Recording
10-3, 60, 97
Tandem CO Line Connections
10-1, 10-2, 15
Tenant Service
15, 39, 77-1
Toll Restriction
10, 30, 41 ~ 48
Toll Restriction Override
10-1, 30, 39, 44B
Toll Restriction Override Code Revision
30
Transfer Privacy
10-1
Traveling Class
44B
Verifiable Account Codes
15, 30, 60, 69, 70
Voice Mail Interface
10-2, 31, 39
Voice or Tone Signaling
05, 10-1, 10-2
Volume Reset (Digital Telephones)
92-9
Voluntary Account Codes
39
2-38
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
TABLE 2-A
PROGRAMS 00 ~ 97 IN NUMERICAL ORDER WITH SECTIONS CROSS-REFERENCED
Program
Number
Title
(Applicable Sections)
00
Software Check/Remote Password
Assignments
(Basic System)
01
Logical Station Port Display
(Basic System)
02
Physical Station Port Display
(Basic System)
03
04
Program
Number
Title
(Applicable Sections)
22
Data Interface Unit (DIU) Station Hunting
(Basic System)
28
DSS Console, Attendant Telephone
Assignments (DK16 only)
(Basic System)
29-1
Flexible PCB Slot Assignment
(DK16 only)
(Basic System)
DSS Console Button Assignment, DSS
Console 1 (DK16 only)
(Basic System)
29-2
Logical Port Intercom Number
Assignment
(Basic System)
DSS Console Button Assignment, DSS
Console 2 (DK16 only)
(Basic System)
30
Station Class of Service
(Basic System)
05
Flexible Access Code Numbering
(Basic System)
31
Station Class of Service
(Basic System)
10-1
System Assignments, Part 1 of 3
(Basic System)
32
Automatic Preference
(Basic System)
10-2
System Assignments, Part 2 of 3
(Basic System)
33
Station Hunting (Voice Calls Only)
(Basic System)
10-3
System Assignments, Part 3 of 3
(Basic System)
34
Hold/Park Recall Timing
(Basic System)
12
System Assignments – Basic Timing
(Basic System)
35
Station Class of Service
(Basic System)
13
Defining the Message Center
(Basic System)
36
Fixed Call Forward
(Basic System)
15
Assigning DP/DTMF, Tenant Service to
Individual CO Lines
(Basic System)
37
Ring Transfer (Camp-on) Recall Time
(Basic System)
38
Digital and Electronic Telephone
Buttonstrip Type
(Basic System)
39
Flexible Button Assignments
(Basic System)
40
Station CO Line Access
(Basic System)
16
19
Assigning CO Line Groups (Dial 9 or
81 ~ 88)
(Basic System)
Alternate Background Music (BGM)
Source Slot Assignment
(Basic System)
20
Data Interface Unit (DIU) Configuration
(Basic System)
41
Station Outgoing Call Restriction
(Basic System)
21
Modem Pool Port Assignments
(Basic System)
42-0
CO Line to PBX/CENTREX Connection
(Basic System)
2-39
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
TABLE 2-A
PROGRAMS 00 ~ 97 IN NUMERICAL ORDER WITH SECTIONS CROSS-REFERENCED (continued)
Program
Number
Title
(Applicable Sections)
Program
Number
Title
(Applicable Sections)
42-1~8
PBX/CENTREX Access Code
(Basic System)
50-1
Least Cost Routing Parameters
(Least Cost Routing)
43
0+ Credit Card Dialing Option
(Basic System)
50-2
Least Cost Routing Home Area Code
(Least Cost Routing)
44A
Emergency Bypass of Forced/Verified
Account Codes
(Basic System)
50-31~35 Least Cost Routing Special Codes
(Least Cost Routing)
44B
50-4
Least Cost Routing Long Distance
Information (LDI) Route Plan
(Least Cost Routing)
50-5
Least Cost Routing Local Call Route
Plan Number
(Least Cost Routing)
50-6
Least Cost Routing Dial Zero Timeout
(Least Cost Routing)
51
Least Cost Routing Area Codes
(Least Cost Routing)
52
Toll Restriction Override Code
(Toll Restriction)
Least Cost Routing Office Code
Exceptions for Specified Area Code
(Least Cost Routing)
53
Toll Restriction Allowed/Denied Area
Codes Assigned by Class
(Toll Restriction)
Least Cost Routing Schedule
Assignments
(Least Cost Routing)
54
Least Cost Routing Route Definition
(Least Cost Routing)
55-0
Least Cost Routing Modified Digits–
Delete
(Least Cost Routing)
Toll Restriction/Traveling Class Override
Codes
(Toll Restriction)
45-1
LCR/Toll Restriction Dial Plan
(Toll Restriction)
45-2
Toll Restriction Disable
(Toll Restriction)
45-3~6
Equal Access/Special Common Carrier
Numbers and Authorization Code Digit
Length
(Toll Restriction)
45-8~9
46-2~4
46-6~8
Toll Restriction Allowed/Denied Office
Codes Assigned by Class
(Toll Restriction)
46-10
Toll Restriction Class 1 Parameters
(Toll Restriction)
55-1~2
Least Cost Routing Modified Digits–Add
(Least Cost Routing)
46-20
Toll Restriction Class 2 Parameters
(Toll Restriction)
56
46-30
Toll Restriction Class 3 Parameters
(Toll Restriction)
Least Cost Routing Station Group
Assignments
(Least Cost Routing)
60
46-40
Toll Restriction Class 4 Parameters
(Toll Restriction)
47
Toll Restriction Exception Office Codes
Assigned by Area Codes
(Toll Restriction)
Station Message Detail Recording
(SMDDR) Output/Account Code Digit
Length
(Basic System)
69
Verified Account Codes
(Basic System)
48
Station Toll Restriction Classification
(Toll Restriction)
2-40
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
TABLE 2-A
PROGRAMS 00 ~ 97 IN NUMERICAL ORDER WITH SECTIONS CROSS-REFERENCED (continued)
Program
Number
Title
(Applicable Sections)
70
Verified Account Code Toll Restriction
Assignments
(Basic System)
77-1
Peripheral Options (Door Phones/IMDU/
PIOU/PIOUS)
(Basic System)
77-2
Door Phone Busy Signal/Door Lock
Assignments
(Basic System)
78
CO Line Special Ringing Assignments –
DISA/IMDU/Night Ringing Over External
Page
(Basic System)
Program
Number
Title
(Applicable Sections)
84
DAY2 IMMEDIATE Ringing
(Basic System)
85
DAY2 DELAY1 Ringing
(Basic System)
86
DAY2 DELAY2 Ringing
(Basic System)
87
NIGHT IMMEDIATE Ringing
(Basic System)
88
NIGHT DELAY1 Ringing
(Basic System)
89
NIGHT DELAY2 Ringing
(Basic System)
79
Door Phone Ringing
(Basic System)
90
Initializing Program 00 ~ 97
(Basic System)
80
Digital and Electronic Telephone Ringing
Tones
(Basic System)
92
81
DAY IMMEDIATE Ringing
(Basic System)
Initializing Speed Dial Numbers, VM ID
Codes, Character Message Memory, Timed
Reminder, Digital Telephone Volume, and
Call Forward Backup RAM
(Basic System)
82
DAY DELAY1 Ringing
(Basic System)
93
CO Line Identification
(Basic System)
83
DAY DELAY2 Ringing
(Basic System)
97
Printing Program Data through SMDR
(Basic System)
2-41
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
IMPORTANT STRATA DK8 AND DK16 PORT INFORMATION
General
There are two types of ports in the STRATA DK8 and DK16 system: Physical Ports and Logical Ports.
This distinction of ports gives customers greater mobility in relocating their stations (telephones).
Physical Ports and Logical Ports
Physical Ports can be defined as the actual system hardware—PCB circuit, wiring, and RJ-11 jack that
stations plug into. Logical Ports are attributes associated with a station (telephone)—station intercom
number, Speed Dial numbers, and the complement of features assigned to the station in system software
programs. A Logical Port is always associated with a Physical Port.
Physical Ports can be considered as fixed; they cannot be moved unless a PCB is removed from the
KSU, Base or Expansion Unit. Logical Ports, though, are not fixed. They can be moved from one Physical
Port to another. It is important to note that Logical Ports can only be moved to related Physical Ports. For
example, you can move a digital telephone (Logical Port) to another digital Physical Port (circuit), but you
cannot move a digital telephone to an electronic telephone circuit Physical Port.
When entering ports into program data, except for Program 01, always enter the Logical Port number.
2-42
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
another program
more data
1
2
3
Spkr
Hold
Step 1
Step 2
Enter Program Mode Enter Program Number
P
S
Spkr
Hold
Step 3
Enter Program Data
H
S
and/or
Spkr
Hold
Spkr
Hold
Step 4
Step 5
Exit Current Program Exit Program Mode
H
Z
Z
(LED buttons)
See Notes
FIGURE 2-2
PROGRAMMING BUTTON SEQUENCE OVERVIEW
The System Record contains programming forms for Programs 00 ~ 97. A System Record should be
filled out for each system installed as detailed in Chapters 1 and 2.
Each System Record Sheet is supplemented with a guide at the top of it for entering data from it. The
guide illustrates the button sequence a programmer must press, with the exception of sequences common
to all programs, e.g., entering programming mode (P), exiting current program (Z), and exiting programming
mode (Z). To save space, these common sequences are coded, as illustrated above. The Spkr and Hold
buttons are also coded “S” and “H,” respectively, to save space.
NOTES:
1. Programs 90, 92, and 03 are out of order and placed in front purposely because they must always be completed first and
in this order. Upon completing these steps, begin with Program 00.
2. Do not Press Intercom when entering Step 1.
2-43
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 90
INITIALIZING PROGRAMS 00 ~ 97
P
S
9
0
H
Enter programming mode
S
#
01
02
H
Z
Z
EXIT
programming
mode
Program(s) to
be initialized
END
Program 90
LEDs 01 and 02
must be lit
LEDs 01 and 02
must flash
IMPORTANT
Initialize Programs 00 ~ 97 every time :
• A new system is installed
• To bring a system's programming back to the default setting
Specify the range as follows:
0
0
9
7
To initialize one program at a time, just enter the individual
program number, then #.
NOTES:
1. Always complete Program 90 at new system installs, before
programming anything else. Skipping this step may cause erratic
system behavior.
2. Follow instructions in Table 1-C (Section 100-816-301) to clear this
data.
3. When Program 90 is run, it will initialize any program or range of
Programs without cycling system power.
WARNING!
Running this program will erase customer data.
2-44
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 92
INITIALIZING SPEED DIAL NUMBERS, VM ID CODES CHARACTER MESSAGE MEMORY, TIMED
REMINDERS, DIGITAL TELEPHONE VOLUME, AND CALL FORWARD BACKUP RAM
more data
P
S
9
2
H
S
H
Enter programming mode
SELECT = (as below)
Z
Z
END
Program 92
1
01
03
Clears Station Speed Dial, Voice Mail ID Codes,
and LCD memos assigned to Station Speed Dial numbers.
2
01
04
Clears System Speed Dial and LCD memos assigned to
System Speed Dial numbers.
3
02
03
Clears Character Message Memory (Station and System)
and user Name/Number display.
4
02
04
Clears Timed Reminders.
5
01
05
Sets speaker volume level to approximately mid-range for intercom
tone/BGM, busy override tone (muted ring), and ringing on all
digital telephones.4
6
02
04
Clears and prevents CO line access blocking.
9
03
04
H
Power OFF
5 seconds;
then Power ON
EXIT
programming
mode
5
Clears Call Forward Memory and Call Forward
indications on telephones.
NOTES:
1. IMPORTANT: It is mandatory to complete all parts of Program 92 at every
new system install. If Program 92 is not completed, certain feature operations may cause erratic system behavior.
2. Use the instructions in Table 1-D (Section 100-816-301) to clear this data.
3. Program 92-9 does not affect Fixed Call Forward settings.
4. Program 92-5 does not affect digital telephone handset/headset receiver
volume levels. To set off-hook handset/headset receiver volume levels
individually for each digital telephone, see Program 30, LEDs 12 and 13.
5. Power “OFF” and “ON” is required to clear telephone LCD Call Forward
Displays and Call Forward button LEDs. Call Forward memory is cleared
when Program 92-9 is run, even if system power is not cycled.
WARNING!
Running this program will erase customer data.
2-45
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 03
DK16 FLEXIBLE PCB SLOT ASSIGNMENTS
P
S
0
3
H
S
H
SELECT = Slot Number
BASE UNIT/
FIXED SLOTS
SLOT NO.
PCB CODE
PCB TYPE/
FIXED SLOT
00
2
91
Common
Control
02
01
2
2
Digital
Ckts
05
06
07
2
11
61
04
31
CO
Ckts
KSTU
OPTIONS
STA. PORT #s
CO/LINE#s
—
—
2
08~11
00~07
Z
Z
When Complete:
POWER OFF
for 5 sec. then
POWER ON
5
CARD = PCB Code
See Reference Table
EXPANSION UNIT
FLEXIBLE SLOTS
03
To Store Data
2
2
01~04
Slot 04 ~ 06 (Expansion Unit assignment criteria):
• Only one type of station card (except for KCDU) is allowed
(maximum); 1-PDKU, or 1-PEKU, or 1-PESU, or 1-PSTU, or
2-KCDUs.
• If KCDU is installed: PDKU, PEKU, PESU, PSTU, or PCOU
cannot be installed; PIOU or another KCDU can be installed.
• Station and CO line PCBs should be installed in slots 04
and 05.
• PIOU should be installed in slot 06.
• Slot 07 should be left empty.
NOTES:
1. See instructions in Table 1-E (Section 100-816-301) to input the data
from this record.
2. Initialized data.
3. PESU circuits: 1 and 2, standard telephones; 3 and 4, not used; 5 ~ 8,
electronic telephones. Total 8 station ports used in software.
4. OCA or PDIU-DI(2)/PDIU-DS will function only with Code 62 or 64
(Base Unit digital telephone circuits and PDKU).
5. System Power must always be cycled after running Program 03.
6. Off-hook Call Announce (OCA) and Data Interface Units (PDIU-DI(2)
and PDIU-DS) will not work in Slots 06 and 07.
7. KCDU does not support DSS connection. PDIU-DI(2)/PDIU-DS or OCA
will function with Code 66 only.
8. Digital telephones cannot support OCA and PDIU-DIs/PDIU-DI2s
simultaneously.
9. Special PCB codes are not required for ADM or DDCB installation.
10. This program is not necessary for DK8.
2-46
PCB CODE
Reference Table
PCB FIXED
SLOT
CODE PORTS/TYPE
COMMON
CONTROL
91
NONE
COMMON
CONTROL
WITH K4RCU
92
NONE
PIOU/PIOUS
41
NONE
PEKU
21
8/STA.
PEKU
W/EOCU
22
8/STA.
PEKU
W/DSS
23
8/STA.
PEKU
W/EOCU,
DSS
24
8/STA.
PESU
25
See Note 3
PESU
W/EOCU
26
See Note 3
KSTU AND
PSTU
31
8/STA.
BASE UNIT CO
CKTs AND
PCOU
11
4/CO
BASE UNIT
DKT CKTs
4
AND PDKU
61
8/STA.
BASE UNIT
DKT CKTs
4
AND PDKU
W/DIU or OCA
62
8/STA.
BASE UNIT
DKT CKTs
4
AND PDKU
WITH DSS
(WITH OR
WITHOUT DIU
OR OCA)
64
8/STA.
65
2/CO
4/STA.
KCDU
OCA or DIU
66
2/CO
4/STA.
NONE
00
NONE
7
KCDU
7
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 00
SOFTWARE CHECK/REMOTE MAINTENANCE SECURITY CODE ASSIGNMENTS
P
S
0
0
H
S
H
SELECT = Select Code
Enter 0 to check Software version.
Enter 1 to change 1st level password.
Enter 2 to change 2nd level password.
Enter 8 to check software sum.
Enter 9 to check power down or
power loss counter since Program 00
was last initialized.
See Note 3.
Select
Code
Z
Z
Password Codes
Enter the 4-digit password.
Password or S/W Check Codes
Item
0
ROM Version
= VERSION =
1
1st Level Password
=
2
2nd Level Password
=
8
Software RAM Checksum
=
9
Power Cycle Counter
=
•
See Note 4.
See Note 5.
See Note 5.
NOTES:
1. See instructions in Table 1-F (Section 100-816-301) to program the system with this
information.
2. Initialized passwords are 0000.
3. The LCD responds as follows, when a selection is made:
0 Version =
1 Password =
2 Password =
8 Sum =
9 Counter =
4. This selection is not programmable. It identifies the system's software version as follows:
VERSION = PSSA
•
ROM Version
ROM Type for DK16
VERSION = QMA
•
ROM Version
ROM Type for DK8
5. These selections are not programmable. They are for factory test purposes only. The
Checksum and Counter vary as customer data is entered.
2-47
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 01
LOGICAL STATION PORT DISPLAY
P
S
0
1
H
H
Z
Physical Port
Enter the Physical Port.
The port’s associated
Logical Port will appear
on the LCD.
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Record port locations on Program 04 System Record Sheet.
3. Initialized data (Program 90) is logical Port No. = Physical Port No.
2-48
Z
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 02
PHYSICAL STATION PORT DISPLAY
P
S
0
1
H
H
Z
Logical Port
Enter the Logical Port.
The port’s associated
Physical Port will appear
on the LCD.
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Record port locations on Program 04 System Record Sheet.
3. Initialized data (Program 90) is Logical Port No. = Physical Port No.
2-49
Z
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 04
LOGICAL PORT INTERCOM NUMBER ASSIGNMENT
P
S
0
4
H
S
H
SELECT = Logical
Port Number
Z
Z
INT = Station Number
NOTE: Shaded areas apply to DK16 only
Intercom
Logical Numbers
Ports (Initialized)
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
(20)
(21)
(22)
(23)
(24)
(25)
(26)
(27)
(28)
(29)
Physical
Ports
(Initialized)
Station Location and Type
(00)
(01)
(02)
(03)
(04)
(05)
(06)
(07)
(08)
(09)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
DK16 Expansion Unit Station PCB Type
PDKU
, PEKU
, 1st KCDU
Circuit Types
DK16 — 8-Digit Ports from Base
Unit
DK8 — 4-Digital Ports from Main
PCB
DK8 — first QCDU
DK8 — second QCDU
4-Standard Telephone Ports from
DK16 optional KSTU in Base Unit
or 2 Standard Telephone ports
from DK8 QSTU.
8-Universal Ports in optional
Expansion Unit. (DK16 only)
Only one type of circuit card
allowed:
1-PDKU, or 1-PEKU, or 1-PESU,
or 1-PSTU or 2-KCDU
✓
, Slot No(s) ______
, 2nd KCDU
, PSTU
, PESU
NOTE:
Peripheral Device Port Options: Devices other than telephones or Data Interface Units can be connected to the
ports listed below. If a peripheral device is connected to a Physical Port, the Logical Port must have same port no.
as the Physical Port.
• Port 00 – DK16 — Digital telephone associated with DSS Console.
• Port 02 and 03 – DK8 — Digital Door Phone/Lock Control Unit (DDCB).
• Port 04 – DK16 — Digital Door Phone/Lock Control Unit (DDCB).
• Port 07 – DK16 — Digital Direct Station Selection Console (DDSS).
• Port 10 – DK8 — DISA Port number used for Toll Restriction Class and Verified/Forced Account Code
assignment.
• Port 11 – DK16 — Separate Background Music Source (KSTU required in Base Unit).
• Port 12 – DK16 — Digital telephone associated with DSS Console (PDKU/Expansion Unit required) or DDCB.
• Port 12 – DK16 — Electronic telephone associated with DSS Console (PEKU/Expansion Unit required).
• Port 14 or 19 – DK16 — Separate Background Music Source (PEKU, PESU, or PSTU/Expansion Unit
required).
• Port 17 & 18 – DK16 — PESU or PEKU ports connected to external amplifier to provide external amplified
conference and /or DISA.
• Port 18 & 19 – DK16 — Electronic Direct Station Selection console (HDSS) (PEKU/Expansion Unit required).
• Port 19 – DK16 — Digital Direct Station Selection console (DDSS) (PDKU/Expansion Unit required).
• Port 20 – DK16 — DISA Port number used for Toll, Class and Verified/Forced Account Code assignments.
2-50
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 05
FLEXIBLE ACCESS CODE NUMBERING
P
S
0
5
H
S
H
SELECT = Access Code 1~9
from the Table Below
Access
Code
0
1
2
3
4
5
6
7
8
9
Z
Z
SPECIAL DIAL = New Access Codes
See Note 6 Below.
Features Affected (N/A = Not Affected)
Unused
Voice First/Tone First (N/A)(1)
Station LCD Messages (10 ~ 19)
New
Access
Codes
Station Intercom Numbers (N/A) (10 ~ 19)
Station Speed Dial Set (10 ~ 49)
Busy Override (N/A) (2)
Do Not Disturb Override (N/A) (2)
Executive Override (N/A) (3)
All Call Voice Page (30)
All Call Voice Page with External Spkrs (39)
Station Intercom Numbers (N/A) (20 ~ 29)7
Off-hook Call Announce (N/A) (2)
External Page Zones(35 ~ 38)7
Group Page (Internal) (31 ~ 34)
Flash (45)
Account Code Input (46)
T.R. Override/T. Class Code Input (47)
BGM Over Stations - ON (481)
BGM Over Stations - OFF (480)
BGM Over External Speakers ON (491)
BGM Over External Speakers OFF (490)
Cancel Message Waiting at Station (No MW
button) (409)
• Telephone Page (530)
Voluntary Account Code (*50)
• Directed Pickup of CO Line on Hold
Door Phones (551 ~ 556),
(57
,
= 01 ~ 08 for DK16, 01 ~ 04 for
Call Pickup:
• Station (5+Station No.)
DK8)
• Ringing CO Line (59)
• External Page (531, 535 ~ 538)
Auto Relocation ON (6282)
LCD Message Set (68)
Auto Relocation OFF (6281)
DKT Mute Ring Adjust (6101)
Auto Relocation Special Dial ON (6283)
DKT Ring Level Adjust (6102)
Auto Relocation-Special Dial Disconnect
IMDU Access (619)7
(626)
Date Set (651)
Auto Relocation-Special Dial Connect
Time Set (652)
(627)
Weekday Set (653)
Call Forward (601, 602, 603, 604)
T.R. Override Code Change (654, 655)
Timed Reminder (605 ~ 609)
System Speed Dial/LCD Messages (60 ~ 99)
MW for Voice Mail ON (63+Station No.)
LCD User Name (621-Set, 620-Reset)
MW for Voice Mail OFF (64+Station No.)
DISA Security Code Change (658)
Voice Mail ID Code Set (Call Fwd, 656)
Verified Account Code Change (659)
Voice Mail ID Code Set (Ans. MW, 657)
Traveling Class Code 1 ~ 4 Change (622 ~ 625)
CO Outgoing Calls (701-708 for DK16 or 701 ~ 704 for DK8)
Message Waiting Set/Cancel (N/A) (7) (77)
CO Group Outgoing Calls (81 ~ 88 for DK16 or 81 ~ 84 for DK8)
Least Cost Routing or CO Group (9)
Automatic Callback (N/A) (4)
CO Line Queuing (N/A) (4)
Station Number Display (401)
Port Number Display (402)
Hold/Park (41)
Hold/Park Pickup (42)
Automatic Busy Redial (44)
Automatic Busy Redial Cancel (44)
Message Waiting Answer (408)
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Be sure access code changes do not conflict with existing access code or station numbering schemes. Refer to Program 04 – Port/Station Number
Assignment.
3. To insert a blank, press programming Button/LED 01.
4. If access codes are being changed to a number that is currently assigned, change the currently assigned code to an unused code first. In the
initialized state, the only unused code is zero (0).
5. The initialized station number sequence of 10 ~ 29 may not be globally changed through Program 05. Make changes through Program 04.
6. The first digit of an access code can be replaced by 2 digits. Standard Access codes are shown for reference.
7. Applies to DK16 only.
2-51
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 10-1
SYSTEM ASSIGNMENTS, PART 1 OF 3
P
S
1
0
H
S
1
SELECT = 1
Button/LED
X
H
Z
Z
Button/LEDs
Light LEDs as described
in the table below
LED On
LED Off
20
2
Two CO Conference/Allowed6
Not Allowed
19
2
Conference/Allowed
Not Allowed
2
Ring Detect Time - Normal
Ring Detect Time – Short Rings
17
Intercom Volume PAD (-8 dB)
No Intercom PAD
16
–
–
15
–
–
148
CO Line Dial Pulse Rate; 20PPS
CO Line Dial Pulse Rate; 10PPS
13
–
–
12
ABR Cycles/10 times
15 times
11
ABR Redial time/30 sec.
1 min.
10
System Speed Dial Override Toll Restriction
Restricted
18
09
2
Exclusive Hold/Allowed
Not Allowed
08
2
Alternate Point Answer
Transfer Privacy
074
2
Ring Transfer of CO Lines Allowed
Not Allowed
06
CO Repeat Ringing
Standard Ring
05
Incoming Call Abandon/8 sec.
6 sec.
043
CO DTMF Signal Time/160 msec.
80 msec.3
03
DP Make Ratio/33%
40%
027
0.45 or 1.5 sec. per Program 42-0
CO line re-seize guard time 0.45
01
Tone First (from DKTs/EKTs)
Voice First (from DKTs/EKTs)
5
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data lights LEDs 07, 08, 09, 18, 19, and 20.
3. LED 04 DTMF Signal Time applies to manual and Speed Dial tones sent out of the system via CO lines. LED 04 does not apply
to Call Forward or voice mail ID DTMF tones sent to voice mail ports. (See Program 10-2, LED 06, for tones sent to voice mail
ports.)
4. If Ring Transfer is allowed, set Ring Transfer Recall time in Program 37; if ring transfer is not allowed (LED 07 off), the station
will recall immediately if transfer is attempted.
5. Standard ring pattern is 1 sec. on, 3 sec. off.
6. Two CO conference must be allowed for DISA operation.
7. CO line guard time is the time interval the system requires to release a CO line and allows it to be re-seized. If LED 02 is off,
all lines are set with 0.45 second guard time; if LED is on, guard time is 0.45 or 1.5 seconds per Program 42-0.
8. This option selects CO line dial pulse rate for DK8 only, see Program 15-2 to select DK16 dial pulse rate.
2-52
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 10-2
SYSTEM ASSIGNMENTS, PART 2 OF 3
P
S
1
0
H
S
H
2
SELECT = 2
Z
Z
Button/LEDs
Light LEDs as defined by the table below.
ALL LEDs with an "X" should be lit when you finish
NOTE: Shaded areas apply to DK16 only
Button/LED
X
LED On
LED Off
20
–
–
1910
Station External Amp Conference
No External Amplifier Connected
18
Two CO Line Conference
No Two CO Line Conference
“TRNS” Immediate (Soft Key)
“TRNS” Normal (Soft Key)
16
2
Executive Override Warning Tone/ON
Executive Override Warning Tone/OFF
156
2
External Page included with All Call Page
Not Included
14
2
Privacy Override Warning Tone/ON
Privacy Override Warning Tone/OFF
13
Send Auto Callback Camp-on Tone3
No Callback Tone
12
CO Line 3 min Beep Tone
No Beep Tone
17
7
11
No DTMF Tone Return
DTMF Tone Return
104, 11
BGM connected to QSTU (DK8), PORT 19;
PESU (DK16), Circuit 89,10
Telephone connected to CKT
094
BGM connected to PEKU, Circuit 39,10
Telephone connected to CKT
08
Display Dialed Number/1min.
Display Dialed Number/15 sec.
075
Standard Tel., CO Ring
per Prog. 10-1, LED 06
Standard Tel. CO Ring Distinctive
06
VM ID Code DTMF Signal Time 80 ms
8
160 ms
05
DISA Busy Tone, 0.5 second cadence
DISA Busy Tone, 0.25 second cadence
04
MW cancel from VM; dial 6 4 & Station No.
MW cancel from VM: Automatic
03
Ringing Modes/3
Ringing Modes/2
Hunt/C.F. override from DSS console's phone
Hunt/C.F. override from DSS console
Tone First (from DSS Console)
Voice First (from DSS Console)
02
01
2
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data lights LEDs 02, 14, 15 and 16.
3. Called party receives notification tone when calling party activates Automatic Callback.
4. BGM connected to QSTU/PSTU/PEKU/PESU/KSTU, will be sent to electronic and digital telephone speakers and external page
(optional). Important: Power must be turned off and on for BGM assignments to be effective.
5. Ring pattern for standard telephones: distinctive ring on incoming CO calls, is: 0.2 sec. on, 0.4 sec. off, 0.2 sec. on, 3.4 sec. off; intercom
ring is always 1 sec. on, 3 sec. off. This doesn't apply to voice mail ports (Program 31, LED 17 on) which are always standard ring.
6. External speakers and designated digital and electronic telephones are paged by dialing Intercom 3 9. The All Call Page button is
used only to page designated digital and electronic telephones.
7. Deletes DTMF tones returned to digital and electronic telephones when dialing from dialpad or speed dialing; also deletes auto dial digits
sent to callers that are call forwarded to voice mail. This does not affect the actual DTMF tones sent out to the CO or voice mail.
8. 0.5 second cadence, Bell Standard Busy Tone, should be enabled so outside callers are not confused by STRATA 0.25 second busy
tone when calling busy number on DISA line calls.
9. If BGM source is assigned to KSTU or PSTU slot in Program 19, system automatically assigns KSTU or PSTU CKT 4 as a BGM source.
10. Important: LED 19 should be OFF unless external amplifiers are used for two CO line/station conference (see Program 10-3). If LED 19
is ON, the station may be unbalanced and receive HUM if external amplifier with Auto-Gain-Control is not connected.
11. BGM connected to QSTU, circuit 2, (DK8) Port 19 may require an isolation transformer per Section 100-816-207
2-53
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 10-3
SYSTEM ASSIGNMENTS, PART 3 OF 3
P
S
1
0
H
S
3
SELECT = 3
H
Z
Z
Button LEDs
Light LEDs as defined by the table below.
ALL LEDs with an "X" should be lit when you finish.
NOTE: Shaded areas apply to DK16 only
Button/LED
X
LED ON
LED OFF
20
LCD BLF Displays Port Numbers
(00 ~ 19, DK16) or (00 ~ 09, DK8)
LCD BLF Displays Station Numbers
(10 ~ 29, DK16, 10 ~ 19, DK8)
19
Speed Dial Entry Timeout: 3 minutes
Speed Dial Entry Timeout: 1 minute
QSMU Option: TTY
QSMU Option: SMDR
PEKU/PESU Ports 17, 18 —
Amp. Circuits 6 and 7
Ports 17,18 — Stations Connected
18
17
16
15
14
13
12
11
10
09
08
07
06
05
046
03
023, 4, 5
01
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data: all LEDs off.
3. See Section 100-816-208 for connecting two-way amplifiers for use on tandem, DISA, and conference telephone calls.
4. See Program 10-2 (LEDs 18 and 19), Program 10-1 (LEDs 19 and 20), and Program 15-5 for more information regarding
two CO line conference/tandem.
5. The amplifier, which is switched to two CO line calls automatically, is accessed on a first-come-first-serve basis. Two CO
line calls established while the amplifier is already being accessed will not be amplified.
6. QSMU option is for DK8 only.
2-54
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 12
SYSTEM ASSIGNMENTS - BASIC TIMING
P
S
1
H
2
S
H
SELECT = 3~9
Enter program code,
3 ~ 9, from table below.
Program Code
36
4
5
9
6
Pause Timing
(Speed Dial)
Flash Timing
4
Pause After Flash
(Voice Path Delay)
QRCU or
K4RCU Inter-digital
Release Time
(Standard Phone)
Z
SELECT CODE = Enter required
code for the time listed in the
table below. See Note 3.
Required
Code
Time
Function
Z
1
1.5 sec.
2
3.0 sec.
1
0.5 sec.
2
2.0 sec.
4
0.2 sec.5
0
no pause
1
1.5 sec.
2
3 sec.
1
1 sec.
through
through
9
9 sec.
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data programs timing as follows: Code 3 = 1, Code 4 = 2, Code 5 = 0, and Code 9 = 4.
3. When programming Code 9, the LCD responds with “LINE TIME =” instead of “SELECT CODE =.”
4. The duration of time the CO line circuit opens Tip & Ring when the Flash button is pressed or when
the hookflash code Cnf/Trn 4 5 is dialed.
5. This timing is not normally used in the United States.
6. This timing applies to voice calls originated from telephones and voice or data calls originated by Data
Interface Units, PDIU-DI(2)s or PDIU-DSs.
2-55
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 13
DEFINING THE MESSAGE CENTER
P
S
1
3
H
S
1
H
Z
Z
PORT = Logical Port Number
Enter the Logical Port number
of the station to be defined
as the Message Center.
SELECT = 1
Port
Number
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Any electronic or digital telephone may receive (and store) up to 3 message waiting indications from any
other digital or electronic telephone. A fourth message waiting indication may be set by the Message
Center, which can only be a voice mail device or a digital or electronic telephone.
3. The Message Center is allowed to perform “Message Waiting,” even if disallowed on all other stations.
4. Initialized data = no port assigned.
5. The message center feature should be assigned to the customer's main answering position: a station or the
lowest port (in the voice mail group) of the customer's voice mail device (see Program 31 for voice mail
group port assignment), whichever the customer specifies.
2-56
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 15
ASSIGNING DP/DTMF, TENANT SERVICE TO INDIVIDUAL CO LINES
P
S
1
5
H
S
H
Z
Z
SELECT = Program Code
Button/LEDs = CO Line
Specify CO lines by setting LEDs, as defined by the table below.
All LEDs with an "X" should be lit when finished.
NOTE: Shaded areas apply to DK16 only
Program
Code
LED Status
Program
ON
OFF
0
AR VM Calls/D
Tone3,6,7,8
Detect
Ignore
1
CO Outgoing Signal5
DP
DTMF
29
CO Dial Pulse Rate
(Pulse per sec.)
20 PPS
10 PPS
3
AR Hold/Ring
Transfer3,8
Detect
Ignore
4
AR Timing3
Crossbar
95 msec.
ESS (Electronic)
450 msec.
5
Equipped
Tandem CO Line
Connection with Station
Dropout4
6
CO Line Tenant
Assignment
Tenant 2
Tenant 1
7
Forced Account Code
Equipped
Not Equipped
8
Operation After Flash
No QRCU
after flash
QRCU/K4RCU
after flash
CO Lines 01 ~ 08
(Button/LEDs)
01
02
03
04
05
07
08
06
(01) (02) (03) (04) (05) (06) (07) (08)
Not Equipped
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data is all LEDs Off.
3. AR = Automatic Release signal. This is a momentary open of the CO line loop provided by some Central Offices. If
programmed to recognize AR, CO lines on-hold will drop when the outside party hangs up and the CO sends AR signal. Two
CO line DISA calls always release with AR. DISA line release is not related to this program—DISA calls always release with
AR signal. AR is sometimes referred to as “Calling Party Control” or “Supervised Loop Control.”
4. Tandem connection must be equipped for all DISA CO lines and all other lines used for two CO line conference.
5. If a CO line is set for Dial Pulse (DP) operation, the Tone Dial Select button must be programmed on stations that must send
DTMF tones over the CO lines. (See Program 39 to assign feature buttons.)
6. When AR is sent on a CO line call because the outside caller hangs-up, “D” tone will be sent to the voice mail (VM) port (QSTU/
PSTU/PESU/KSTU), prompting the VM machine to release and clear the port for another call.
7. The system will detect the AR signal (auto release) and drop the voice mail port when the outside caller hangs up. (See Note
3 for AR explanation.)
8. If the CO line is enabled to detect AR, the CO line will disconnect anytime during a call if the Central Office sends the AR signal.
If AR is sent when talking on a CO line with an LCD telephone, the LCD will display, “CO LINE HANG UP.”
9. See Program 10-1, LED 14, to select DK8 dial pulse rate.
2-57
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 16
ASSIGNING CO LINE GROUPS (DIAL 9 OR 81 ~ 88)
P
S
1
6
H
S
H
SELECT = CO Line Group
Only enter the last digit of
the CO line group (1 ~ 8) to
be defined, or enter 0 for Dial 9 group.
NOTE: Shaded areas apply to DK16 only
CO
LED Line
08
(08)
07
(07)
06
(06)
05
(05)
04
(04)
03
(03)
02
(02)
01
(01)
81 (1)
82 (2)
83 (3)
84 (4)
Z
Button/LEDs
Specify which CO lines are assigned to the
group by setting LEDs as defined by the table
below. All LEDs with an "X" should be lit
when finished. See Note 2.
CO Line Groups
85 (5)
86 (6)
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns all CO lines to the Dial 9 group.
2-58
Z
87 (7)
88 (8)
Dial 9 (0)
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 198
DK16 ALTERNATE BACKGROUND MUSIC (BGM) SOURCE SLOT ASSIGNMENT
P
S
1
9
H
S
1
SELECT = 1
H
Z
Z
SLOT
KSTU: Slot 03
PSTU/PESU/PEKU: Slot 04 ~ 07
Slot number of PSTU, KSTU, PEKU,
or PESU connected to background
music (BGM) source
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. If PEKU, the BGM source must be wired to Circuit 3. (Program 10-2.)
3. If PESU, the BGM source must be wired to Circuit 8. (Program 10-2.)
4. If KSTU or PSTU, the BGM source must be wired to Circuit 4 and may require an isolation transformer
per Section 100-816-207.
5 If connecting the source to a PEKU or PESU, turn on LED 09 or 10 in Program 10-2. If connecting BGM
to a KSTU or PSTU, LEDs 09 and 10 in Program 10-2 do not apply.
6. The PDKU and the KCDU will not support a BGM source.
7. Initalized Data is “BLANK”. Press Button/LED 01, to enter BLANKS.
8. Alternate BGM source is assigned to DK8 QSTU, Port 19, using Program 10-2, LED 10. Program 19
is not necessary for DK8.
9. System power must be cycled for this program to take effect.
2-59
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 20
DATA INTERFACE UNIT (DIU) PORT CONFIGURATION
P
Select =
S
2
0
H
20
19
18
17
H
Logical Port Number that is connected to
PDIU-DS or to DKT with PDIU-DI(2).
Port Number
LED
S
X
LED ON
Z
Button/LEDs1 ~ 5 defines data port type;
Button/LEDs 17 ~ 20 assigns data port to
security group.
Port Number
LED OFF
LED
Data Security
Group 4
Data Security
Group 2
Not
Included
Not
Included
20
Data Security
Group 3
Data Security
Group 1
Not
Included
Not
Included
18
19
17
X
Z
LED ON
Port Number
LED OFF
LED
Data Security
Group 4
Data Security
Group 2
Not
Included
Not
Included
20
Data Security
Group 3
Data Security
Group 1
Not
Included
Not
Included
18
19
17
16
16
16
15
15
15
14
14
14
13
13
13
12
12
12
11
11
11
10
10
10
09
09
09
08
08
08
07
07
07
X
LED ON
LED OFF
Data Security
Group 4
Data Security
Group 2
Not
Included
Not
Included
Data Security
Group 3
Data Security
Group 1
Not
Included
Not
Included
06
DTR Pulse With5
Data Release
No DTR
Pulse
06
DTR Pulse With5
Data Release
No DTR
Pulse
06
DTR Pulse With5
Data Release
No DTR
Pulse
05
Auto Pause3
Behind PBX
No Auto
Pause
05
Auto Pause3
Behind PBX
No Auto
Pause
05
Auto Pause3
Behind PBX
No Auto
Pause
04
PDIU-DS
Connected
PDIU-DI(2)6
Connected
04
PDIU-DS
Connected
PDIU-DI(2)6
Connected
04
PDIU-DS
Connected
PDIU-DI(2)6
Connected
03
PDIU-DS to
Modem
Connection
AT Commands
and Result Codes
PDIU-DS to other
type DCE or DTE
03
PDIU-DS to other
type DCE or DTE
03
02
AT Dial
Command Only
02
PDIU-DS to
Modem
Connection
AT Commands
and Result Codes
PDIU-DS to other
type DCE or DTE
AT Dial
Command Only
PDIU-DS to
Modem
Connection
AT Commands
and Result Codes
DIU
Connected
No DIU
Connected
01
DIU
Connected
No DIU
Connected
01
DIU
Connected
No DIU
Connected
02
01
AT Dial
Command Only
NOTES:
1. For more information, see the instructions preceding the record sheets. Copy this page if more than three DIUs are installed.
2. Initialized data: LED 17 ON, all others OFF.
3. Auto pause will be inserted after a Centrex or PBX access code is dialed by a DIU: CO line must be assigned in Program
42-0 and must have access code assigned in Program 42 (1 ~ 8). Pause time is determined by Program 12-3. A pause will
also be inserted after the DK CO line access code is dialed (by the DIU) in all cases if LED 05 is turned on.
4. DIUs can connect to any digital circuit in the Base Unit and on the PDKU2 and KCDU, but it can only connect to Circuits 1
~ 7 on the PDKU1.
5. If a PDIU-DS is connected to a modem, turn LED 06 ON to cause the modem to disconnect the line when the user presses
the Data Release button. Modem should be sent AT Command “AT & D2” so it can recognize DTR pulse, and the PDIU-DS
SW1-2 switch must be off (in the up position). This feature is for outgoing modem calls only—DTR will not pulse on incoming
modem calls. Always change the modem escape sequence from “+ + +” to some other character using the “ATS2=____”
command; this allows AT commands to be sent to the modem or DIU independently.
6. The PDIU-DI connects to 1000-series Digital Telephones, and the PDIU-DI2 connects to 2000-series Digital Telephones.
2-60
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 21
MODEM POOL PORT ASSIGNMENTS
P
S
2
1
H
S
H
Digital Telephone Port/PDIU-DS Port Number
PDIU-DS Logical Port Number
Z
Z
Standard Telephone
Port/Modem Port Number
Modem Logical Port Number
Assignment 1
Assignment 2
Assignment 3
Assignment 4
Assignment 5
Assignment 6
Assignment 7
Assignment 8
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data is blank.
3. DIUs can connect to any digital circuit (port) in the DK16 Base Unit or DK8 KSU, on the PDKU2, and on the KCDU or QCDU,
but can only connect to Circuits 1 ~ 7 on the PDKU1.
2-61
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 22
DATA INTERFACE UNIT (DIU) STATION HUNTING (DATA CALLS ONLY)
P
S
2
2
H
S
H
SELECT = Logical Port Number
Enter the DIU port number
of the “Hunt-From”
station. See Note 3 for
entering a range of ports.
Z
Z
HUNT TO =
Enter the Hunt To
DIU Logical Port
number. See Note 4.
NOTE: Shaded areas apply to DK16 only
Logical
Port
00
01
02
03
16
17
18
19
04
05
06
07
08
09
10
Hunt To
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data does not assign “Hunt-To” points to any port.
3. A range of ports may be assigned by pressing the following button sequence:
Low port
High port
4. Press Button/LED 01 to delete a digit from “Hunt-To” port.
5. Program 22 applies to PDIU-DI(2) and PDIU-DS data stations. If programming a PDIUDI(2) station, use the associated digital telephone Logical Port number; the PDIU-DS
is programmed using its own unique Logical Port number.
2-62
11
12
13
14
15
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 28
DK16 DSS CONSOLE/ATTENDANT TELEPHONE ASSIGNMENTS
P
S
2
8
H
S
SELECT = (1~2)
Enter the DSS
console number.
See Note 4.
Base Unit/Expansion Unit PCB Slot
(Lowest Slot to Highest)
DSS Console
(DDSS/HDSS)
Number
Base Unit (Digital Circuits):
1
Expansion Unit PCB (PEKU or PDKU):
2
H
Z
Z
DSS ATT = (1~2)
Enter the attendant digital or electronic
telephone number. See Note 5.
Attendant Digital / Electronic
Telephone Number (1 or 2)
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. A digital DDSS console can be assigned to an electronic telephone, and an HDSS console can be assigned to a digital telephone.
3. Refer to Program 03, Flexible PCB Slot Assignments, for the PEKU, PDKU, Base Unit slots configured to support consoles.
4. If more than one console is associated with one attendant telephone, then specify the same number attendant telephone for both
consoles associated with it.
5. Initialized data assigns console #1 to attendant telephone #1 and console #2 to attendant telephone #2.
6. DSS consoles are not available on DK8.
2-63
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 29-1, 29-27
DK16 DSS CONSOLE (DDSS AND HDSS) BUTTON ASSIGNMENTS
CONSOLE
P
S
2
9
H
1
S
H
SELECT = 1 or 2 for consoles 1 or 2, respectively
DSS Number 1~2:
Each system can have up to two consoles. Enter the
console to which buttons are being assigned (DSS
console 1).
No. 01 ~ No. 20
Press the button/LED
that is in the same
position as the console
button being assigned.
The LED lights and the
LCD displays the console
button's number.
DSS Button Group 1~3:
Each console has three groups
of 20 LED buttons. Choose the
group to be assigned.
Z
Z
Code:
Assign the appropriate
SpeedDial, CO line
access, or DSS station
access code to the button
chosen. See code table
below for the buttons to
enter. See Notes 4 and 5.
Copy this sheet as required and enter the console number and corresponding Select number.
Console Number
Group No. 1
Button/Code
Group No. 2
Button/Code
Button/Code
Button/Code
Group No. 3
Button/Code
Button/Code
10
20
10
20
10
20
09
19
09
19
09
19
08
18
08
18
08
18
07
17
07
17
07
17
06
16
06
16
06
16
05
15
05
15
05
15
04
14
04
14
04
14
03
13
03
13
03
13
02
12
02
12
02
12
01
11
01
11
01
11
Code Table
Button Type
Station Speed Dial
System Speed Dial
CO Line Access
Code
* 10 ~ * 49
* 60 ~ * 99
01 ~ 08
DSS (Station Access) #00 ~ #19
AC
89
NT1
91
NT2
92
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns the Base Unit, PEKU, or PDKU console to operate with
the telephone connected to the Base Unit’s first digital port or the PEKU or
PDKU's first port, respectively. See Program 28 to reassign a console to another
telephone, if desired.
3. When assigning CO line access buttons (01 ~ 08) to the DSS console, the
associated telephone must be assigned access to the CO line. See Program 40.
4. Initialized data assigns the AC (Code 89) to Group No. 3 Button19 and the NT
button (Code 91) to Group No. 3 Button 20 on all consoles. All other buttons are
initialized as DSS and SD (for Station Speed Dial) buttons. Initialized button
assignments are shown after this record sheet.
5. The NT and AC buttons may be changed to DSS, CO or SD buttons, but they
may not be reassigned to other locations.
6. Important: Only program SD, CO, DSS, AC, and NT buttons; programming
other feature buttons on a console may cause system operation problems.
7. DSS consoles are not available on DK8.
2-64
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 29
DK16 INITIALIZED DSS CONSOLE (DDSS AND HDSS) BUTTON ASSIGNMENTS
#09
#19
#08
#18
#07
#17
#06
#16
#05
#15
#04
#14
#03
#13
#02
#12
#01
#11
#00
#10
* 19
* 18
* 17
* 16
* 15
* 14
* 13
* 12
* 11
* 10
* 29
* 28
* 27
* 26
* 25
* 24
* 23
* 22
* 21
* 20
DSS Keys
* 39
* 38
* 37
* 36
* 35
* 34
* 33
* 32
* 31
* 30
Speed Dial Keys
2-65
NT1(91)
AC(89)
* 47
* 46
* 45
* 44
* 43
* 42
* 41
* 40
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 30
STATION CLASS OF SERVICE
P
S
3
0
H
S
H
Z
Z
SELECT = Logical Port Number(s)
Enter the logical port number(s) to which class of service
Button/LEDs
must be assigned. See Note 3 for entering a range of ports. Light LEDs for the port specified in the last step. All Button/
LEDs marked with an “X” in the table below should be lit.
NOTE: Shaded areas apply to DK16 only
Feature
LED
20
19
18
17
Priv. Override Allowed5,6
Exec. Override Allowed6
DND Override Allowed6
Change T.C.O. Code9
Change Verified A.C.10
Account Codes Verified
Digital Tele. Recv. Vol.13
Digital Tele. Recv. Vol.13
Dial Pulse/(DTMF Off)8
Change DISA Security Code7
Change TR Override Code11
Forced Acc't Code
OCA/Busy Override Automatic4
ABR Access Enabled15
Speed Dial Allowed
Mic on at Start of Call12
Mic Button Lock Enabled12
Speakerphone Enabled
Logical Port Numbers and DISA Port 20 14
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20
16
15
14
13
12
11
10
09
08
07
06
05
04
03
02
01
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data reads LEDs 01, 05, 07, and 12 ON for all ports.
3. A range of ports may be specified by entering:
Low port
High port
4. If this LED is turned OFF, OCA and Busy Override must be accessed manually by dialing 2. If kept ON, ACB and Executive Override
cannot be accessed.
5. If all stations are allowed Privacy Override, (the system will be non-private), allowing up to three telephones to talk on the same
CO line.
6. See Program 10-2 to enable/disable Priv./Exec./DND override warning tones.
7. To change DISA code from selected stations: Dial Intercom 6 5 8 + code + Redial.
8. DP or DTMF is specified for standard telephones only, KSTU, PSTU, or PESU (Circuits 1 and 2) in DK16, QSTU in DK8.
9. To change a four-digit Traveling Class Override (T.C.O.) code: Dial Intercom + ˚˚˚ + code + Redial.
˚˚˚ = 6 2 2 - Class 1, 6 2 3 - Class 2, 6 2 4 - Class 3, 6 2 5 - Class 4.
10. To change Verified Account Codes from selected stations: Dial Intercom + 6 5 9 + Code Number (000 ~ 299) for DK16; (000 ~ 099)
for DK8 + code (1 ~ 15 digits) + Redial. Note that the total Account Code digit length is set in Program 60-4; all digits do not have
to be verified.
11. To change the four-digit T. R. override codes (1 or 2) from selected stations: Dial Intercom + 6 5 4 + code + Redial; or Intercom
+ 6 5 5 + code + Redial.
12. Mic ON/OFF at start of call (LED 03 ON = Mic ON, LED 03 OFF = Mic OFF) is only in effect if Mic button lock is enabled (LED 02
= ON).
13. There are nine handset receiver volume levels, 1 ~ 9 (9 being the highest). The initial off-hook level can be set anywhere from level
2 to 5. Set the initial level with one of the following combinations: Level 2 = 12 OFF/13 OFF; Level 3 = 12 ON/13 OFF (default level);
Level 4 = 12 OFF/13 ON; Level 5 = 12 ON/13 ON.
14. To require DISA callers to dial Verified Forced Account Codes before accessing outside CO lines, light LEDs 08 and 14 on DK16
(Port 20) or DK8, (Port 10).
15. For ABR to function, QRCU (DK8) or K4RCU (DK16) must be installed to detect busy tone.
2-66
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 31
STATION CLASS OF SERVICE
P
S
3
1
H
S
H
SELECT = Logical Port Number(s)
Enter the Logical Port number(s) to which class
of service must be assigned.
See Note 3 for entering a range of ports.
LED
VP (B + Station No.)
20
VP (B + No Station)
Block Exec./Priv. Ovr. 6
19
18
End/End Signal Rcv (VM)
Receive VM ID Code
VP Integration (A/D)
Group Page 4 - EKTs/DKTs
Group Page 3 - EKTs/DKTs
Group Page 2 - EKTs/DKTs
Group Page 1 - EKTs/DKTs
AC Page - EKTs/DKTs 7
VM (No Conference)
VM Group 4
17
16
15
14
13
12
11
VM Group 3
VM Group 2
VM Group 1
VM to VM Call Blocking 5
OCA Enabled (Receive)
Handsfree No Warning
Handsfree Disabled
Z
Button/LEDs
Light LEDs for the port
specified in the last step. All
buttons/LEDs marked with an
“X” in the table below should
be lit.
NOTE: Shaded areas apply to DK16 only
Feature
Z
Logical Port Numbers
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19
10
09
08
07
06
05
04
03
02
01
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data reads LED 10 ON for all ports.
3. A range of ports may be specified by entering:
Low port
4.
5.
6.
7.
High port
If Button/LED 15 is lit, Button/LED 17 must be lit.
If Button/LED 19 is lit, Button/LED 17 must be lit.
If Button/LED 20 is lit, Button/LEDs 17 and 19 must both be lit.
Voice Mail (VM) to VM call block should be ON for all VM (QSTU, KSTU/PSTU/PESU) ports if the VM/Auto Attendant
machine does supervised and/or screened transfer.
Block Exec./Priv. override (LED 18 ON) prevents Privacy Override to the selected station unless the
Privacy Release button is ON at that station; this option (LED 18 ON) prevents Executive Override to the station under
all conditions.
Button/LED 10 enables (disables) a telephone to receive an All Call page. All telephones can initiate an All Call page.
2-67
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 32
AUTOMATIC PREFERENCE
A
S
3
2
H
SELECT = Logical Port Number
Enter the Logical Port number of the
station having preference defined.
See Note 3 below for entering
a range of ports.
S
H
DATA = Ringing Code
Enter 0 to disable Ringing Line Preference.
Enter 1 to enable Ringing Line Preference.
Z
Z
Automatic Preference Code:
Enter 00 for no selection.
Enter 01 for intercom.
Enter 02 for lowest CO line.
Enter 11 ~ 18 for Line Groups 1~ 8.
NOTE: Shaded areas apply to DK16 only
Logical
Port
Number
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
Ringing
Code
(0 or 1)
Automatic
Preference
Code
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns Ringing Code 1 and Automatic Off-hook Code 00 for all ports.
3. To enter a range of ports dial the following button sequence:
Low port
High port
4. Automatic Preference applies to going off-hook (lifting the handset) and pressing the Spkr button.
5. This program applies to digital and electronic telephones only; standard telephones always select the system intercom path
when going off-hook (lifting the handset).
2-68
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 33
STATION HUNTING (VOICE CALLS ONLY)
P
S
3
3
H
S
H
SELECT = Logical Port Number (00~19)
Enter the Logical Port number
of the “Hunt-From” station.
See Note 3 for entering
a range of ports.
Z
Z
HUNT TO = Logical Port Number (00~19)
Enter the “Hunt-To”
Logical Port number.
See Note 4.
NOTE: Shaded areas apply to DK16 only
Logical
Port
00
01
02
03
16
17
18
19
04
05
06
07
08
09
10
11
12
13
Hunt To
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data does not assign “Hunt-To” points to any port.
3. A range of ports may be assigned by pressing the following button sequence:
Low port
4. Press Button/LED 01 to delete a digit from a ”Hunt-To” port.
5. If a hunt station is in the Call Forward mode, calls will be directed to the
forwarded destination.
6. CO lines will hunt if they are programmed to ring at the Hunt station only;
CO lines that ring at more than one station in any given ring program (81 ~ 89).
2-69
High port
14
15
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 34
HOLD/PARK RECALL TIMING
A
S
3
4
H
S
H
SELECT = Logical Port Number (00~19)
Enter the port number having
its Hold/Park Recall Time defined.
See Note 4 for entering a
range of ports.
Z
Z
HOLD TIME = Seconds
Enter the number of seconds the
system will wait. Use three digits.
Acceptable range is 000 or
011~160. See Note 3.
NOTE: Shaded areas apply to DK16 only
Logical
Port
00
01
02
03
16
17
18
19
04
05
06
07
08
09
10
11
Seconds
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns a Hold /Park recall time of 032 seconds to all ports.
3. Enter 000 for no Hold/Park recall. Enter 011 ~ 160 for 11 to 160 seconds.
4. Enter a range of ports by keying in the following sequence:
Low port
2-70
High port
12
13
14
15
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 35
STATION CLASS OF SERVICE
P
S
3
5
H
S
H
SELECT = Logical Port Number (00~19)
Enter the port number(s) being
defined. See Note 3 for
entering a range of ports.
Z
Z
Button/LEDs
Select LEDs to light for the port specified
in the last step. All LEDs marked with
an “X” in the table below should be lit.
NOTE: Shaded areas apply to DK16 only
Feature
LED
Busy Station Transfer5
Busy Station Ring6
Automatic Hold
Disable continuous DTMF
tones on DKT 20008
20
19
18
17
No CF/NA on Handsfree7
16
15
14
13
12
11
10
09
08
07
06
05
04
03
02
01
LCD Indiv. Message
Message Waiting (RCV)
LCD Type/32-ON/12-OFF4
LCD Display4
Logical Port Numbers
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data reads Buttons/LEDs 01, 02, 04, and 05 lit for ports.
3. Enter a range of ports by keying in the following sequence:
Low port
High port
4. Button/LEDs 01, 02, and 04 should be lit for all stations connected to voice mail (VM) ports to allow proper VM
integration. Button/LEDs 01 and 02 should be lit for all stations (even non-LCD), unless it is desired to disable the LCD
and message waiting indication.
5. This feature applies to calling ports (typically VM/auto attendant ports) that transfer CO line calls (can be telephone
stations, too).
6. This feature applies to called ports (stations) that must receive calls from VM/auto attendant ports (can be telephone
stations, too) when busy.
7. Does not apply to Off-hook Call Announce calls; OCA calls will forward after 12 seconds (CFNA time out) if not
answered.
8. May be required for dialing with Personal Computers connected to 2000-series digital telephone (PDIU-DI2) data
interface units.
2-71
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 36
FIXED CALL FORWARD
P
S
3
6
H
S
H
SELECT = Logical Port Number (00~19)
Enter the port number of the
station that needs a Fixed
Call Forward location
assigned. See Note 3 for
a range of ports.
Z
Z
FORWARD TEL = Port Number (00~19)
Enter the port number of
the station or VM port that
will be call forwarded to
when the Fixed Call Forward
button is pressed.
NOTE: Shaded areas apply to DK16 only
Logical
Port
00
01
02
03
16
17
18
19
04
05
06
07
08
09
10
11
Forward
Tel
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data does not assign a Fixed Call Forward location to any port.
3. To enter a range of ports, key in the following sequence:
Low port
4.
5.
6.
7.
8.
High port
Press Button/LED 01 to enter blanks.
See Program 39, Code 86, to assign Fixed Call Forward buttons on DKTs/EKTs.
Fixed Call Forward will forward all calls to the designated port.
Stations that have Fixed Call Forward set will not ring.
Program 92-9 does not clear Fixed Call Forward memory.
2-72
12
13
14
15
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 37
RING TRANSFER (CAMP-ON) RECALL TIME
P
S
3
7
H
S
H
SELECT = Logical Port Number (00~19)
Enter the number of the port that
needs a Ring Transfer Recall time
assigned. See Note 3 for
entering a range of ports.
Z
Z
HOLD TIME = Ring Transfer Recall Time
Enter the Ring Transfer Recall
Time (in seconds). The acceptable
range is 011 ~ 999 seconds. Use
three digits.
NOTE: Shaded areas apply to DK16 only
Logical
Port
00
01
02
03
16
17
18
19
04
05
06
07
08
09
10
11
12
13
14
15
Hold
Time
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns a Ring Transfer Recall Time of 032 seconds to all ports.
3. To enter a range of ports, key in the sequence:
Low port
High port
4. Ring Transfer Recall Time is the time it takes to recall a station that originates an unanswered or busy (camped-on)
transferred call.
5. Ring Transfer must be allowed (Program 10-1, LED 07 ON) for transfer recall to function; otherwise Recall will be immediate.
6. Ring Transfer to stations in the Do Not Disturb Mode is not allowed; recall will be immediate if it is attempted—no matter what
the Program 37 recall time is.
2-73
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 38
DIGITAL AND ELECTRONIC TELEPHONE BUTTONSTRIP TYPE
P
S
3
8
H
S
H
SELECT = Logical Port Number (00~19)
Enter the port number of the station
that needs a keystrip defined.
See Note 4 for entering a range of ports.
00
01
02
03
16
17
18
19
Z
KEY MENU = Code
Enter the appropriate code as follows:
Telephone Type
10-key (DK8/16)
20-key (DK8/16)
20-key (DK8)
20-key (DK16)
Code
21
31
32
33
See Note 5 ~ 10Speed Dial
NOTE: Shaded areas apply to DK16 only
Logical
Port
Z
04
05
06
07
08
09
10
11
12
13
Key
Menu
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns Code 31 to all ports.
3. Always complete Program 38 beforeproceeding to Program 39.
4. To enter a range of ports, key in the sequence:
Low port
High port
5. The DK8 default for 2000-series digital telephone keystrips assigned by codes are as follows:
Speed Dial
All Call
Voice Page
Speed Dial
SD14
Speed Dial
Do Not Disturb
SD13
Do Not Disturb
SD13
Do Not Disturb
SD12
SD12
DSS17
SD12
SD22
SD11
SD11
DSS16
SD11
SD21
SD10
SD10
DSS15
SD10
SD20
Line4
Line 4
DSS14
Line 4
SD19
Line 3
Line 3
DSS13
Line 3
SD18
Line 2
Line 2
DSS12
Line 2
SD17
Line 1
Line1
DSS11
Line1
SD16
Intercom
Intercom
DSS10
Intercom
SD15
Code 21
10-button
Code 31 (Initialized)
20-button
Code 32
20-button
6. The DK8 default 1000-series digital telephone keystrip assigned by codes are as follows:
Do Not Speed
DSS15 DSS16 DSS17 Disturb Dial
SD20
SD21
Do Not Speed
SD22 Disturb Dial
DSS10 DSS11 DSS12 DSS13 DSS14
SD15
SD16
SD13
SD18
SD19
All Call
Voice Page
SD10
SD11
SD12
SD13
SD14
SD105
SD11
SD127
SD13
Intercom Line 1 Line 2 Line 3 Line 4
Code 31 (Initialized)
20-button
Intercom Line 1 Line 2 Line 3 Line 4
Code 32
20-button
2-74
14
15
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 38 (continued)
ELECTRONIC AND DIGITAL TELEPHONE KEYSTRIP TYPE
7. The DK16 default for 2000-series digital telephone keystrips assigned by codes are as follows:
Speed Dial
SD10
Speed Dail
SD 10
Flash
Do Not Disturb
Line 8
Do Not Disturb
Line 8
Do Not Disturb
Line 7
Line 7
SD18
Line 7
Speed Dial
Line 6
Line 6
SD17
Line 6
Redial
Line 5
Line 5
SD16
Line 5
Spd Dial Pause
Line 4
Line 4
SD15
Line 4
SD 15
Line 3
Line 3
SD14
Line 3
SD 14
Line 2
Line 2
SD13
Line 2
SD 13
Line 1
Line 1
SD12
Line 1
SD 12
Intercom
Intercom
SD11
Intercom
Code 21
SD 11
Code 31 (Initialized)
Code 33
8. The DK16 default 1000-series digital telephone keystrips assigned by the codes are as follows:
SD16
SD17
Do Not Speed
SD18 Disturb Dial
SD11
SD12
SD13
Line 5
SD14
Spd Dial
Speed Do Not
Pause Redial Dial Disturb Flash
SD15
Line 6 Line 7 Line 8
SD10
Intercom Line 1 Line 2 Line 3
Line 4
SD13
SD11
SD12
SD14
SD15
Line 5
Line 6 Line 7 Line 8
SD10
Intercom Line 1 Line 2 Line 3 Line 4
Code 31 (Initialized)
20-button
Code 33
20-button
9. The DK16 electronic telephone keystrip code assignments are as follows:
MW/FL
SD10
MW/FL
SD10
MW/FL
DND
CO7
C08
DND
C08
DND
C07
SD18
C07
SDS
CO6
C06
SD17
C06
RDL
CO5
C05
SD16
C05
PAU
CO4
C04
SD15
C04
SD15
CO3
C03
SD14
C03
SD14
CO2
C02
SD13
C02
SD13
CO1
C01
SD12
C01
SD12
INT
INT
SD11
INT
Code 31 (Initialized)
20-button
Code 21
10-button
SD11
Code 33
20-button
10. DK8 and KD16 Programming templates for the digital and electronic telephones are shown below.
10
20
09
19
08
18
07
17
06
16
05
15
04
14
16
17
18
19
20
03
13
11
12
13
14
15
02
12
06
07
08
09
10
01
11
01
02
03
04
05
1000-Series Digital Telephone
2000-Series Digital Telephone
6500-Series Electronic Telephone
2-75
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
PROGRAM 39
MARCH 1993
FLEXIBLE BUTTON ASSIGNMENT REFERENCE GUIDE
A
S
3
9
H
S
H
SELECT = Port Number
or range. See Note 4.
Press LED/button
to be defined. See tables
on the following pages.
Button
Function
Button
Labels
Account
Code
Account Code
or ACCOUNT
Code
Button
Function
Notes
Code:
Enter the appropriate code that corresponds
to the feature to be assigned. See the
feature code reference table below.
Button
Labels
Code
Notes
72
73
Momentarily unlocks door
(3 or 6 sec.). See Prog. 77-1
and 77-2.
Intercom
or INT
00
Intercom line access key
MSG
81
Begins LCD message
selection
Flash
or MW/FL
99
Provides message waiting
LED for EKT and Flash key
Microphn Cut-off
or MCO
88
Modem
or MODEM
55
Night Transfer
Tenant 1
Night Transfer 1
or NT1
91
Sets Tenant 1 CO
DAY/NIGHT ringing mode
Night Transfer
Tenant 2
Night Transfer 2
or NT2
92
Sets Tenant 2 CO
DAY/NIGHT ringing mode
Pause
Spd Dial Pause
or PAU
95
Sets a pause in Speed
Dial. See Program 12-3
Spd Dial Lng Pause
or PAU/L
93
Sets a 10-second pause
in Speed Dial
Allows a Voluntary Account
Code to be entered
Alarm
Alarm Reset
or ALRM
77
Resets alarm
condition system wide
All Call
Voice Page
All Call Page
or AC
89
Pages all idle electronic/digital
telephones over speaker
Intercom
70
Sets ABR of busy outgoing
number
LCD Message
94
Sets ACB for station
recalled by busy line
Turns BGM ON or OFF
through station speaker
Auto Busy Redial
or ABR
Z
Unlock Door 1
or DRLK 1
Unlock Door 2
or DRLK 2
50
Automatic
Busy Redial
Z
Door Lock 1 and
Door Lock 2
Automatic
Callback Busy
Auto Callback
or ACB
Background
Music
Tel Set Music
or BGM
78
Call Forward
All Calls
Call Frwd All Calls
or CFAC
87
All calls forward to selected
station
Call Forward
A.C. Fixed
Call Frwd to:
or CFF
86
Forwards all calls to pre-defined
destination. See Prog. 36
Call Forward
Busy
Call Frwd Busy
or CFB
59
Forwards calls to selected
station if station is busy
Call Forward
Busy/No
Answer
Call Frwd Busy/
NAns
or CFB/NA
57
Forwards calls to selected
station if station is busy or
does not answer
Call Forward
No Answer
Call Frwd
No Answer
or CFNA
58
Forwards calls to selected
station if station does not answer
Pause (Long)
Directed Pickup
or PKUP
84
Picks up ringing or held intercom,
CO calls, and page
Pooled Line
Pooled Line Grp
or PL
61 ~
68
Call Pickup
Tenant 1
83
Picks up tenant 1
ringing CO calls
Privacy
PKUP1
Privacy On Line
or PRIVACY
53
Prevents Privacy Override
(not Exc. Over.)
Call Pickup
Tenant 2
PKUP2
82
Picks up tenant 2
ringing CO calls
Privacy Release
Privacy Release
or PRV RLS
79
Changes station Privacy
mode to Non-private for COs
Redial Last
Number ( # key)
RDL
(EKT only)
96
CO Line
Appearance
Line 01 ~ 08
or CO 01 ~
CO 08
Redials the last
number
Release Call
or RLS
76
Releases current call
and makes station idle
Save Last Number
or SAVE
85
Saves last number dialed
for future speed dial
Speed Dial
Select ( * key)
Speed Dial
or SDS
97
Begins speed dial
selection
Station Speed
Dial Codes
SD
*10 ~
* 49
Reserves key for
station speed dial
System Speed
Dial Codes
SD
*60 ~
* 99
Speed dial number set
by station port #00
Tone Dial Select
or TONE
90
CO dial signals set to
tone or pulse
Call
Pickup
Used to place data call
Data Release
or DRLS
54
Releases data call
DSS
#00 ~
#95
Do Not
Disturb
Do Not Disturb
or DND
98
Prevents calls to station
Door Lock 0
Unlock Door 0
or DRLK 0
71
Momentarily unlocks door
(3 or 6 sec.) PIOUS/PIOU
Direct Station
Selection
Modem
Release
56
Data Release
Microphone
Cut-off
CO line access of
01 ~ 08
appearing calls
Data Call
or DATA
Data
Message Waiting
and Flash
Save Last
Number
Assigns DSS hotline
keys to port number
Tone
Sets microphone on/off for
incoming handsfree
intercom calls
Used to reserve modem
in modem pool
Multiple CO lines may
appear under one key
NOTES:
1. For more information, see instructions preceding record sheets.
2. Complete Program 38 before Program 39.
3. Initialized data assigns the keystrip pattern associated with Code 31 from Program 38.
4. Specify a range of ports by keying in:
Low port
5.
6.
7.
8.
High port
Flash (FLASH) (MW/FL): Sets pauses in Speed Dial if telephone does not have a pause button. Sets flashes in Speed Dial numbers if telephone has a
pause button.
Redial (REDIAL or RDL) and Speed Dial (SDS): Both buttons must be programmed on Electronic telephones; not allowed separately. Recommended
on all stations using voice mail, since they allow easy access of * and # DTMF buttons (see note 8 below).
Pooled Line Grp (PL): Codes 61 ~ 68 represent CO line groups 81 ~ 88. Maximum four Pooled Line Grp (PL) buttons per pooled line group on each
station.
Redial is a fixed button on 2000-series Digital Telephones and REDIAL is a fixed button on 1000-series Digital telephones. Do not assign button as flexible
button on digital telephones; also, Speed Dial (SDS) is initialized on flexible button 20 on Digital telephones.
2-76
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 39
FLEXIBLE BUTTON ASSIGNMENT FOR PORTS ____ TO ____
A
S
3
9
H
S
H
Port Number
NOTE: Shaded areas apply to DK16 only
BUTTON
Z
Z
Code
LED/Button
SLOT NO. _______ .
CODE
BUTTON
CODE
CODE
BUTTON
CODE
Account Code (ACCOUNT)
50
Directed Pickup 1 (PKUP1)
83
Intercom (INT)
00
Privacy Release (PRV RLS)
79
Alarm Reset (ALRM)
77
Directed Pickup (PKUP2)
82
LCD MSG Select (MSG)
81
Redial (RDL)3
96
All Call Page (AC)
89
Line 1 ~ 08 CO 01 ~ CO 08
Flash (MW/FL)
99
Release Call (RLS)
76
Auto Busy Redial (ABR)
70
Data Call (DATA)
56
Microphn Cut-off (MCO)
88
Save Last Number (SAVE)
85
Auto Callback (ACB)
94
Data Release (DRLS)
54
Modem (MODEM)
55
Speed Dial (SDS)
Tel Set Music (BGM)
78
DSS
Night Transfer 1 (NT1)
91
SD Stations
Call Frwd All Calls (CFAC)
87
#00 ~
#95
Night Transfer 2 (NT2)
92
* 10 ~
* 49
Call Frwd to _ (CFF)
86
Do Not Disturb (DND)
98
Spd Dial Pause (PAU)
95
SD System
Unlock Door 0 (DRLK 0)
71
Spd Dial Lng Pause (PAU/L)
* 60 ~
* 99
Unlock Door 1 (DRLK 1)
72
Pooled Line Grp (PL)
Unlock Door 2 (DRLK 2)
73
Privacy On Line (PRIVACY)
Call Frwd Busy (CFB)
59
Call Frwd Busy/NAns (CFB/NA)
57
Call Frwd No Answer (CFNA)
58
Directed Pickup (PKUP)
84
PORT NO. ____. 10
20
LCD
DIU
LOCATION:
Button
Code
PORT NO. ____. 10
20
01 ~ 08
LCD
DIU
LOCATION:
Button
Code
Button
Code
BUTTON
93
61 ~ 68
PORT NO. ____. 10
20
Code
Button
Code
Tone Dial Select (TONE)
LCD
DIU
PORT NO. ____. 10
20
Button
Code
Button
Code
Button
20
10
20
10
20
10
20
09
19
09
19
09
19
09
19
08
18
08
18
08
18
08
18
07
17
07
17
07
17
07
17
06
16
06
16
06
16
06
16
05
15
05
15
05
15
05
15
04
14
04
14
04
14
04
14
03
13
03
13
03
13
03
13
02
12
02
12
02
12
02
12
01
11
01
11
01
11
01
11
LCD
DIU
LOCATION:
Button
Code
PORT NO. ____. 10
20
LCD
DIU
LOCATION:
Button
Code
Button
Code
PORT NO. ____. 10
20
LCD
DIU
LOCATION:
Button
Code
Button
Code
LCD
DIU
LOCATION:
10
PORT NO. ____. 10
20
90
53
LOCATION:
Button
97
PORT NO. ____. 10
20
Code
LCD
DIU
LOCATION:
Button
Code
Button
Code
Button
10
20
10
20
10
20
10
20
09
19
09
19
09
19
09
19
08
18
08
18
08
18
08
18
07
17
07
17
07
17
07
17
06
16
06
16
06
16
06
16
05
15
05
15
05
15
05
15
04
14
04
14
04
14
04
14
03
13
03
13
03
13
03
13
02
12
02
12
02
12
02
12
01
11
01
11
01
11
01
11
Code
NOTES:
1. DSS buttons are used for voice calls only; SD buttons are used for voice and/or data calls.
2. To allow a station to set * and # DTMF tones in speed dial numbers, the station must have the Speed Dial (SDS) and Redial
(REDIAL) (RDL) buttons. Digital telephones only require the Speed Dial (SDS) button, because the Redial (REDIAL)
button is fixed on them. Digital telephones initialize with the Speed Dial (SDS) button (see Program 38).
3. The Redial (REDIAL) button is fixed on digital telephones; do not assign this button as a flexible button on digital telephones;
also, Speed Dial (SDS) is initialized on flexible button 20 on Digital telephones.
2-77
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 40
STATION CO LINE ACCESS
P
S
4
0
H
S
H
NOTE: Shaded areas apply to DK16 only
08
07
06
05
04
03
02
01
Z
Button/LEDs = CO Lines
Light LEDs for
the port(s) specified.
SELECT = Logical Port Numbers
CO LED
Z
Port Numbers
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20
08
07
06
05
04
03
02
01
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data reads all LEDs ON for all CO lines. Complete CO line access is allowed on all ports.
3. Denying access in this program applies to all access options, including LCR.
4. This program also denies Pickup CO line access.
5. A range of ports may be entered by keying in:
Low port
High port
6. DK16, Port 20 and DK8, Port 10 are used to allow or to deny Direct Inward System (DISA) access.
2-78
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 41
STATION OUTGOING CALL RESTRICTION
P
S
4
0
H
S
H
SELECT = Logical Port Numbers
NOTE: Shaded areas apply to DK16 only
CO LED
08
07
06
05
04
03
02
01
Z
Z
Button/LEDs = CO Lines
Light LEDs for
the port(s) specified.
Port Numbers
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20
08
07
06
05
04
03
02
01
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data reads all LEDs OFF for all CO lines (all stations allowed outgoing access to all CO lines).
3. This program denies all outgoing calls except when using Least Cost Routing.
4. A range of ports may be entered by keying in:
Low port
High port
5. Restricted CO lines may be accessed for ABR calls.
6. DK16, Port 20 and DK8, Port 10 are used to allow or to deny Direct Inward System (DISA) access.
2-79
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 42-0
CO LINE TO PBX/CENTREX CONNECTION
P
S
4
2
H
S
0
SELECT = 0
NOTE: Shaded areas apply to DK16 only
(CO
LED
Line)
08
07
06
05
04
03
02
01
H
Z
Z
Specify CO lines by setting
Button/LEDs as defined by
the table below.
Set Button/LEDs
CENTREX/PBX
Normal
Connection (LED on)
(LED off)
(08)
(07)
(06)
(05)
(04)
(03)
(02)
(01)
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data reads all LEDs OFF for all CO lines.
3. This progam must be utilized to allow CENTREX/PBX (after flash) features to operate.
4. If CO line is programmed for behind CENTREX/PBX (LED ON), re-seize guard time is 1.5 seconds. If CO line
is programmed for normal operation guard time is 0.45 seconds. See Program 10-1, LED 02.
2-80
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 42-1 ~ 8
PBX/CENTREX ACCESS CODES
P
S
4
2
H
S
H
SELECT = 1~8
PBX Access Code Group
Enter the PBX Group
number 1 ~ 8 that needs
an access code assigned.
Z
Z
ACCESS CODE =
Enter a 2-digit access
code for the group,
as defined by the table
below. See Note 3.
PBX/CENTREX
Outgoing Trunk
Access Code(s)
PBX/CENTREX
Access Code
Number
1st digit
2nd digit
1
2
3
4
5
6
7
8
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns no access codes to PBX groups.
3. • If access code is single digit, enter the first digit and press Button/LED 01 as
second digit.
• Press Button/LED 01 to delete a digit.
• Press Button/LED 02 for don't care. For example, pressing 8 + Button/LED
02 allows 80 ~ 89.
4. This program must be utilized to allow correct Toll Restriction and CENTREX/
PBX transfer operation.
2-81
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 43
0+ CREDIT CARD DIALING OPTION
P
S
4
3
H
S
H
SELECT = Logical Port Numbers
NOTE: Shaded areas apply to DK16 only
CO LED
08
07
06
05
04
03
02
01
Z
Z
Button/LEDs = CO Lines
Assigned to allow dial 0+ calls
with selected stations
Logical Port Numbers
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19
08
07
06
05
04
03
02
01
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. For Stations and CO lines enabled in this program: 0+ calls override system Toll Restriction, and calls will
disconnect automatically if the number of digits set in Program 60-7 is not dialed when "0" is dialed as the first
digit. This restricts the operator from placing calls that would be charged back to the telephone line.
2-82
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 44A
EMERGENCY BYPASS OF FORCED/VERIFIED ACCOUNT CODES
P
S
4
4
H
S
H
SELECT = 51, 52, or 53
to set emergency
number 1, 2 or 3
Z
Z
DATA = 3 or 4 digit emergency
telephone number
To enter blanks,
Press: Button/LED 01
Example
Emergency Number 1:
5
1
Emergency Number 2:
5
2
Emergency Number 3:
5
3
9
1
1
911 = Initialized Data (Note 2)
DATA = 3 or 4-digit telephone number
SELECT =
NOTES:
1. The emergency telephone numbers assigned in this program will be sent out the CO line immediately when
dialed; they will bypass the Forced/Verified Account Code dialing restriction.
2. If CO lines are behind PBX or CENTREX, program the PBX/CENTREX outside trunk access code: Example:
"9". A pause is automatically inserted following the first 9. See Programs 42-0 and 42-1 to assign the CO lines
and access codes for behind PBX/CENTREX operation. Also, if the system CO lines are behind CENTREX/
PBX, the CENTREX/PBX trunk access codes must be programmed in front of the emergency telephone
number. Example: If the CENTREX/PBX access code is “9”, then enter 9911 in Program 44-51.
3. If Verified Account Codes assigned in Program 69 conflict (are the same) with emergency telephone numbers
assigned in Program 44A, Program 44A has priority.
4. This feature is for use with Forced (Verified or Nonverified) Account Codes, but not with ABR and DISA. It also
does not override Toll Restriction; emergency numbers must be allowed using system Toll Restriction tables
per normal Toll Restriction programming procedures.
5. Program 44B is related to Toll Restriction and is placed with the other Toll Restriction programs in this chapter.
2-83
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
Programs 44B through 48 can be found in the
Toll Restriction System Record section.
Programs 50 through 56 can be found in the
Least Cost Routing System Record section.
2-84
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 60
SMDR OUTPUT/ACCOUNT CODE DIGIT LENGTH
P
S
6
0
H
S
SELECT = 2 ~ 6 (Item)
Make a selection to indicate
which item is being assigned.
Select 2 for SMDR Threshold
Time.
Select 3 for SMDR output, etc.
H
Z
For “2” SMDR Threshold Time = 0 or 1
For “3” SMDR COR = 0 or 1 (Data)
For “4” ACCOUNT = 04 ~ 15
For “5” TOLL DIAL, 0 ~ 5
For “6” DATA = DISA security code; 1 ~ 15 digits
For "7" CREDIT = Credit Card Digits; 1 ~ 30 digits
Description
Item
Z
Data
TIME
2
SMDR Threshold Time 12
0 = 1.0 seconds
1 = 10 seconds
SMDR Output when a call is completed.
0 = Outgoing Only 1 = Incoming and Outgoing
(SMDR COR)
3
Forced/Voluntary Account Code Digit
Length 04 ~ 15.
(Digits are verified per Prog. 30, LED 14, and
Prog. 69. See Note 4)
(ACCOUNT)
10
4
(TOLL DIAL DATA)
Printout options
Toll Dial = 0
5
All Calls 7
= 1
Dial “0” calls only
= 2
Dial “1” calls only
= 3
Dial “00” calls only
= 4
Dial “1”, “0”, calls only
= 5
Dial “1” or “00” calls only
6
DISA Security Code 9 (may be changed
from station, per Program 30 )
7
Credit card call digit length, 01 ~ 30 digits,
(see Program 43)
DATA
~
CREDIT 11
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. For Selection 3, initialized data assigns SMDR output to be enabled for incoming calls that are answered.
3. For selection 4, initialized data assigns a 6-digit length to all Forced/Voluntary Account Codes.
4. If PBX code is dialed, numbers dialed after the code will be checked.
5. If A/C, O/C or SPCC code begins with "0", "1", or "00", that call will print out.
6. When accessing LCR feature, all digits sent to CO will be output.
7. Programming 60-3-0 (printout outgoing calls only) is still available.
8. Button/LED 1 = blank, Button/LED 2 = don't care.
9. If a security code is not programmed, outgoing CO line access via DISA will not require a security code when dialing.
10. See Program 69 for Verified Account Codes.
11. Number of digits required when "0" is the first digit dialed; if this number of digits is not dialed, the system will disconnect
the call after 20 seconds. "0" is counted as a digit. Example: 0 + 1 + 714 + 583 - 3700 = 12 digits; 12 should be
programmed as a minimum in this case.
12. Default is 10 seconds.
2-85
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 69
VERIFIED ACCOUNT CODES (V.A.C.s)
More Codes
A
S
6
9
H
S
H
SELECT = Verified Account Code Number (VACN)
Z
Z
Verified Account Code (1 ~ 15 digits)
Check to Indicate VACN Range.3 000 ~ 024
Shaded areas apply to DK16 only. 100 ~ 124
200 ~ 224
025 ~ 049
125 ~ 149
225 ~ 249
050 ~ 074
150 ~ 174
250 ~ 274
075 ~ 099
175 ~ 199
275 ~ 299
Copy this sheet as needed. Enter the three digit verified account
code number, for example: 000, 001, etc.
NAME
VACN
(3-Digit)
VERIFIED ACCOUNT CODE (1 ~ 15 DIGITS)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
NOTES:
1. Account Code format:
¥ Account code digit length is defined in Program 60-4 (4 ~ 15 digits).
¥ To dial an Account Code, station users must always dial the quantity of digits defined in Program 60-4.
¥ If the quantity of digits in a Verifified Account Code is the same as the Account Code digit length in Program 60-4, the
all digits will be Verified; if the quantity of digits is less, then only those digits will be Verified.
2. Account Codes may not conflict (be the same as) emergency numbers in Program 44A.
3. DK8 allows 100 V.A.C.s (000 ~ 099); DK16 allows 300 V.A.C.s (000 ~ 299).
2-86
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 70
VERIFIED ACCOUNT CODE TOLL RESTRICTION ASSIGNMENTS
P
S
7
0
H
SELECT = Verified Account
Code Number (VACN)
000 ~ 299
6 Check
}
to
Indicate
VACN Range
NOTE: Shaded areas apply to DK16 only
000 ~ 099
100 ~ 199
200 ~ 299
VACN
(3-Digit)
_00
_01
_02
_03
_04
_05
_06
_07
_08
_09
_10
_11
_12
_13
_14
_15
_16
_17
_18
_19
_20
_21
_22
_23
_24
_25
_26
_27
_28
_29
_30
_31
VAC Digit
Restrict
Code
VAC
Restrict
Code
S
H
DATA = VAC Digit
Restriction Code 0 or 1
Enter 0 for no digit restriction.
Enter 1 for digit restriction.
VACN
(3-Digit)
VAC Digit
Restrict
Code
_32
_33
_34
_35
_36
_37
_38
_39
_40
_41
_42
_43
_44
_45
_46
_47
_48
_49
_50
_51
_52
_53
_54
_55
_56
_57
_58
_59
_60
_61
_62
_63
VAC
Restrict
Code
Z
Z
VAC Restrict Code (0 ~ 6)
Enter 0 for No Station Toll Restriction.
Enter 1 for Area Code Toll Restriction.
Enter 2 for Area Code Toll Restriction
and 0 or 1 as 1st or 2nd digit.
Enter 3 for Class 1 Toll Restriction.
Enter 4 for Class 2 Toll Restriction.
Enter 5 for Class 3 Toll Restriction.
Enter 6 for Class 4 Toll Restriction.
VACN
(3-Digit)
_64
_65
_66
_67
_68
_69
_70
_71
_72
_73
_74
_75
_76
_77
_78
_79
_80
_81
_82
_83
_84
_85
_86
_87
_88
_89
_90
_91
_92
_93
_94
_95
_99
VAC Digit
Restrict
Code
VAC
Restrict
Code
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data reads 00 for all VACNs.
3. This restriction overrides the normal station restriction assigned in Program 48 when a VAC is entered at the
station. The station resumes its Program 48 restriction after the call is disconnected.
4. Range programming is not available.
5. Copy as required.
6. DK16 allow 300 V.A.C. assignments, DK8 allows 100 V.A.C. assignments.
2-87
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 77-1
PERIPHERAL OPTIONS
(DOOR PHONES/IMDU/BASE UNIT RELAY/PIOU/PIOUS)
P
S
7
7
H
S
1
SELECT = 1
NOTE: Shaded areas apply to DK16 only
LED X
H
Z
Z
Button/LED
Light the button/LEDs that are marked
with an X in the table below.
LED ON
LED OFF
20
Door Lock Time/6 sec.
Door Lock Time/3 sec.
17
DDCB2 on DK8/Port 03; DK16/Port 12
DKT on DK8/Port 03; DK16/Port 12
16
DDCB1 on DK8/Port 02; DK16/Port 04
DKT on DK8/Port 02; DK16/Port 04
15
—
14
IMDU Modem (Station 619) Enabled 4
—
IMDU Modem (Station
619)/Disabled 4
13 8
Tenant 2 (NT2) CO lines – K4/Zone 4
Tenant 1 (NT1) CO lines – K4/Zone 4
12 8
Tenant 2 (NT2) CO lines – K3/Zone 3
Tenant 1 (NT1) CO lines – K3/Zone 3
11
8
Tenant 2 (NT2) CO lines – K2/Zone 2
Tenant 1 (NT1) CO lines – K2/Zone 2
10
8
Tenant 2 (NT2) CO lines – K1/Zone 1
Tenant 1 (NT1) CO lines – K1/Zone 1
09
—
08
Door Phone Ring on Ext Page 5
No Ring over Ext Page 5
07
Door Lock Relay Enabled (PIOU/PIOUS) 6
External Page Relay Enabled (PIOU/PIOUS) 6
06
NT Relay During Night Ringing and NT19
NT Relay Steady With NT1 Button
05
MOH Relay Enabled (PIOU/PIOUS)
NT Relay Enabled (PIOU/PIOUS)
04
—
—
03
—
—
02
LED 01 Has Priority7
External Page on Base Unit Relay Enabled7
01
MOH on Base Unit Relay Enabled7
NT on Base Unit Relay Enabled7
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data leaves all LEDs off.
3. Port 12 is in the DK16 Expansion Unit.
4. If a modem unit (IMDU) is installed on a DK16 PIOU or PIOUS, it can be accessed by dialing station 619.
5. If NT1 is turned on at an electronic or digital telephone, then the door phone will ring over external page.
6. This option applies to the PIOU/PIOUS Door Lock Control (Unlock Door0) assigned to digital or electronic
telephones using Code 71 in Program 39; it does not apply to DDCB door locks (Unlock Door1 ~ 2).
7. To program the DK8 or DK16 Key Service Unit relay for the MOH function, LEDs 02 and 01 must be ON;
for the NT function, LED 02 must be ON and LED 01 OFF; for the External Page function, LED 02 must
be OFF, and LED 01 can be ON or OFF.
8. Zone relays 1 ~ 4 require a PIOU in the DK16 Expansion Unit.
9. For this option, CO lines must be assigned to ring over external page in Program 78-13.
2-88
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 77-2
DOOR PHONE BUSY SIGNAL/DOOR LOCK ASIGNMENTS
P
S
7
7
H
S
2
20
X
Z
Z
Button/LED
Light the button LEDs marked with
an X in the table below.
SELECT = 2
LED
H
LED ON
LED OFF
Door Phone Rings One Time
Rings Five Times
19
—
—
18
—
—
17
—
—
16
—
—
15
—
—
14
—
—
13
—
—
12
—
—
11
—
—
10
—
—
09
—
—
08
DDCB2 B-jack is Door Lock Control #2
B is connected to Door Phone 2B
07
Door phone 2C Busy Out
No Busy Signal
06
Door phone 2B Busy Out
No Busy Signal
05
Door phone 2A Busy Out
No Busy Signal
04
DDCB1 B-jack is Door Lock Control #1
B is connected to Door Phone 1B
03
Door phone 1C Busy Out
No Busy Signal
02
Door phone 1B Busy Out
No Busy Signal
01
Door phone 1A Busy Out
No Busy Signal
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data reads all LEDs OFF.
DDCB Port Assignments in Program 77-1
DDCB DK16 Port No. DK8 Port No.
1
04
02
2
12
03
2-89
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 78
CO LINE SPECIAL RINGING ASSIGNMENTS
DISA/IMDU/NIGHT RINGING OVER EXTERNAL PAGE
P
S
7
8
H
S
H
SELECT = Feature Number
Enter Feature Number
Code
1, 2 or 5.
Enter Code
Number 1~3.
Z
Z
CO Line
Specify CO lines by setting
button/LEDs as defined by the
table below. All LEDs with an
"X" should be lit when finished.
NOTE: Shaded areas apply to DK16 only
CO Lines
(Button/LEDs)
Feature
Number
Code
1
3
Ring Over External Page 4 during NIGHT mode
1
DISA CO Line during DAY Mode 3
2
DISA CO Line during DAY2 Mode
3
DISA CO Line during NIGHT Mode
1
Ring IMDU Maint. Modem during DAY Mode
2
Ring IMDU Maint. Modem during DAY2 Mode
3
Ring IMDU Maint. Modem during NIGHT Mode
2
5
Feature Description
01 02 03 04 05 06 07 08
(01) (02) (03) (04) (05) (06) (07) (08)
3
3
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data leaves all LEDs off.
3. See Programs 10-1, 15, 60, 40, 41, 48, and 03 (code 92) for complete DISA programming (for DISA, the
K4RCU PCB must be installed in the Base Unit).
4. See Program 77-1 for night ringing configuration.
5. DISA lines are assigned to DK8 Port 10 and DK16 Port 20 in Program 30 (Account Codes) and Program
41 (outgoing CO line restriction) and Program 48.
2-90
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 79
DOOR PHONE RINGING
P
S
7
9
H
S
H
SELECT = Logical Port Number
Enter the port number having
Door Phone Ringing assigned.
Z
Z
Button/LEDs
Select button/LEDs indicated
in the table below.
NOTE: Shaded areas apply to DK16 only
Feature
LED
Muted ring to busy DKT/EKT5
Door phone 2C Ring
Door phone 2B Ring
Door phone 2A Ring
Door phone 1C Ring
Door phone 1B Ring
Door phone 1A Ring
Logical Port Numbers
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19
20
19
18
17
16
15
14
13
12
11
10
09
08
07
06
05
04
03
02
01
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data does not assign door phone ringing to any station port.
All LEDs are OFF.
3. A range of ports may be entered by keying in the following:
Low port in range
High port in range
4. Door phones can ring any number of digital and electronic telephones, but do not ring standard telephones or
other devices connected to KSTU, PESU, or PSTU station ports.
5. Only the lowest port in a ringing group will receive muted ring tone if all EKTs/DKTs in the ringing group are
busy and the door phone button is pressed.
2-91
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 80
DIGITAL AND ELECTRONIC TELEPHONE RINGING TONES (CO LINE CALLS)
P
S
8
0
H
S
H
SELECT = Logical Port Number
Enter number of port having its
ringing tone defined. See Note 4
for entering a range of ports.
Z
Z
Ringing Tone Code
Enter 1 for Tone 1 (500/640 Hz).
Enter 2 for Tone 2 (600/800 Hz).
NOTE: Shaded areas apply to DK16 only
Ringing Tone (Code)
Port Numbers
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19
Tone 1 (1)
Tone 2 (2)
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns Tone 1 to all station ports.
3. Tone 1 is 500 Hz modulated with 640 Hz.
Tone 2 is 600 Hz modulated with 800 Hz.
4. A range of ports may be specified by entering:
Low port
High port
2-92
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 8
(1 ~ 9)
CO LINE/STATION RINGING ASSIGNMENTS
P
S
8
H
S
H
SELECT = 1 ~ 9
for type of ringing
Z
Z
Button/LEDs = CO Lines
assigned to ring selected port number(s)
SELECT = Logical Port Number(s)
of station(s) that must ring
Selected CO lines ring selected station ports per Ringing Program options as follows:
DAY
8 1 Immediate
8 2 12 second delay
8 3 24 second delay
DAY 2
8 4 Immediate
8 5 12 second delay
8 6 24 second delay
NIGHT
8 7 Immediate
8 8 12 second delay
8 9 24 second delay
NOTE: Shaded areas apply to DK16 only
CO LED
08
07
06
05
04
03
02
01
Logical Port Numbers
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19
08
07
06
05
04
03
02
01
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data reads all LEDs ON for Port 00 in Program 81 and Port 01 in Program 87, all other LEDs are OFF.
3. If a CO line must Call Forward or Hunt from a station, the line must be assigned to ring at that station only.
4. A range of ports may be selected.
2-93
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
System Record Sheets for Programs 90 and 92 are in
the beginning of this section because they must be
executed before any other programs.
2-94
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 93
CO LINE IDENTIFICATION
P
S
9
3
H
S
1
SELECT = 1
Button/LED
Choose the button/LED for
the CO line being named.
See Note 2.
NOTE: Shaded areas apply to DK16 only
LED
08
07
06
05
04
03
02
01
CO
Line
(08)
(07)
(06)
(05)
(04)
(03)
(02)
(01)
H
Z
Z
CO Line Identification
Enter the CO line identification.
(16 alphanumeric characters
is the maximum.)
See Note 3 for LCD message editing.
CO Line Identification (16 Characters Max. – Enter One Per Square)
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns no identification message to CO lines.
3. Special editing buttons include:
# to toggle between alpha and numeric modes;
1 moves cursor to right;
* moves cursor to left;
0 increments letters, etc.
For more detailed editing instructions, see the following page.
2-95
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 93 (continued)
CO LINE INDENTIFICATION ALPHA/NUMERIC ENTRY
1) Enter Program 93 and select the desired CO line.
2) Use the guide below to enter CO line identification information.
Numeric Mode
“0” to “9” are treated as numerals.
NOTE: Dialpad starts out in Numeric Mode.
Use # button to switch to Alpha Mode
and vice versa.
Moves cursor to
right, and starts
special character
entry when in
the Alpha Mode
Moves cursor
to left
QZ
ABC
DEF
1
2
3
GHI
JKL
MNO
4
5
6
PRS
TUV
WXY
7
8
9
Cursor
Left
Scroll
Key
0
Mode
Key
#
*
Changes from
Numeric to
Alpha Mode
and vice versa
Scrolls alpha and
special characters
Alpha Entry (Example):
Special Character Entry:
A
2
“Q”
1 0
B
2 0
“Z”
1 0 0
C
2 0 0
“:”
1 0 0 0
“–”
1 0 0 0 0
“+”
1 0 0 0 0 0
“/”
1 0 0 0 0 0 0
Alpha
Character
Entry
Sequence
Special
Character
2-96
Entry
Sequence
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 97
PRINTING PROGRAM DATA THROUGH SMDR
P
S
9
7
H
S
H
SELECT = Program Number
to be printed on SMDR.
See Note 2 for entering
a range of programs.
DATA PRINT
Printout begins.
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Enter a range of programs by keying:
Low port
High port
2-97
Z
Z
Spkr##Hold
Cancels printout
at any time.
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
SETTING THE DATE, TIME AND DAY
HOW TO SET THE DATE
The date can be set from an LCD electronic or digital telephone connected to a logical port 00.
Press the following button sequence with the handset on-hook:
Intercom
6
5
1
Redial
Date in year/month/day
format (YYMMDD). If month
or day is a single digit, precede
with a zero (0).
Electronic telephones can use
the # button if they do not have
the Redial (RDL) button.
HOW TO SET THE TIME
The time can be set from an LCD electronic or digital telephone connected to a logical port 00.
Press the following button sequence with the handset on-hook:
Intercom
6
5
2
Redial
Time in hours/minutes/seconds
format (HHMMSS from 000000
to 235959). If any of these values
is a single digit, precede with a
zero (0).
Electronic telephones can use
the # button if they do not have
the Redial (RDL) button.
HOW TO SET THE DAY
The day can be set from an LCD electronic or digital telephone connected to a logical port 00.
Press the following button sequence with the handset on-hook:
Intercom
6
5
Enter the digit for today's day:
1 = Sunday
2 = Monday
3 = Tuesday
4 = Wednesday
5 = Thursday
6 = Friday
7 = Saturday
3
Redial
Electronic telephones can use
the # button if they do not have
the Redial (RDL) button.
NOTES:
1. The date, time and day can be set immediately following initialization or after programming is completed.
2. The system should not be in programming mode for the date, time and day to be set.
2-98
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAMMING PROCEDURES
TOLL RESTRICTION SYSTEM RECORD SECTION
Programs 44B ~ 48
2-99
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 44B
TOLL RESTRICTION/TRAVELING CLASS OVERRIDE CODES
P
S
4
4
H
S
H
SELECT = Toll restriction
Class 1 ~ 4
Z
Z
DATA = 4-digit Toll Restriction Code
for Selected Class
Code for Toll Restriction Class
1
Code for Toll Restriction Class
2
Code for Toll Restriction Class
3
Code for Toll Restriction Class
4
DATA = 4-Digit code
SELECT =
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Classes 1 ~ 4 are defined in Program 46.
3. When the Toll Restriction override code is dialed, the station's class defined in Program 48 will be changed
to the class assigned to the code in Program 44B.
4. Do not use same codes set in Program 45 (8 ~ 9).
5. Stations enabled in Program 30, Button/LED 16 ON, are allowed to enter and change Toll Restriction Class
(1 ~ 4) override codes.
2-100
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 45-1
LCR/TOLL RESTRICTION DIAL PLAN
P
S
4
5
H
S
SELECT = 1
X
Plan
1
H
Z
Z
DATA = Plan 1 ~ 5
Enter codes 1 ~ 5 to indicate
the dial plan for the system.
Toll Restriction/LCR
Dial Plans
5
0+ (Note 6)
4
Universal (Note 6)
3
1+AC+NXX/NNX
2
1+AC+NXX/1+NNX (Note 7)
1
AC+NXX/1+NNX (Note 7)
IMPORTANT: The correct Dial Plan must be assigned to allow system LCR and/or Toll
Restriction to function properly.
NOTES:
1. Initialized data assigns Dial Plan Code 1 to the system.
2. In NXX and NNX, X = 0 ~ 9, N = 2 ~ 9.
3. NXX = Office code (interchangeable; 2nd digit can be 1 or 0).
4. NNX = Office code (not interchangeable; 2nd digit cannot be 1 or 0).
5. AC = Area Code.
6. 0+ and Universal (Codes 5 + 4) are not used in USA.
7. 1+ NNX indicates 1 may be dialed before office codes.
2-101
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 45-2
TOLL RESTRICTION DISABLE
P
S
4
5
H
S
2
H
NOTE: Shaded areas apply to DK16 only
08
07
06
05
04
03
02
01
CO
Line
08
07
06
05
04
03
02
01
Z
Button/LEDs
Specify CO lines by setting
button/LEDs as defined by the
table below. All LEDs with an
"X" should be lit when finished.
ON = Disable Toll Restriction
SELECT = 2
LED
Z
X
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data reads all LEDs OFF for all CO lines.
2-102
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 45-3 ~ 6
EQUAL ACCESS/SPECIAL COMMON CARRIER (SPCC) NUMBERS AND AUTHORIZATION CODE DIGIT
LENGTH
P
S
4
5
H
S
H
DATA =
First five digits of the
SPCC Number, or digit
length specified in the
table below. See Note 3.
SELECT = Item 3~6
Enter Item number
3~6 from table below.
Item
Description
3
SPCC1 Number
4
Authorization Code 1
Digit Length (00 ~ 99)
5
SPCC2
6
Authorization Code 2
Digit Length (00 ~ 99)
Z
Data =
1st five digits of SPCC
Number or
Digit Length
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns “00” data to items 4 and 6, and assigns blank data to
items 3 and 5.
3. When editing,
• Press # to move cursor.
• Press Button/LED 01 to delete or leave a blank.
• Press Button/LED 02 for don't care.
4. Do not enter a digit length greater than necessary or Toll Restriction may be
able to be defeated.
5. This program is designed for the following special Common Carrier access
dialing sequence: SPCC Number + Authorization Code + Telephone Number
(950XXXX). SMDR will print out the following: SPCC Number +----+ Telephone Number. (The Authorization Code will not print out, and four dashes ("---") will be in its place.) Toll Restriction will start on the first digit of the
Telephone Number.
2-103
Z
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 45-8 ~ 9
TOLL RESTRICTION OVERRIDE CODE
P
S
4
5
H
S
H
SELECT = 8 or 9
Enter 8 to Select Code 1.
Enter 9 to Select Code 2.
Z
DATA = Code
Enter the 4-digit code
from the table below.
Code (4 digits)
Select =
8
Code 1
9
Code 2
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. When editing the data field, use Button/LED 01 to delete a digit; Button/LED
02 for don't care.
3. Initialized data leaves code assignments blank.
4. Codes may be revised by station users specified in Program 30, LED 09.
5. Do not use same 4-digit codes set in Program 44B, Toll Restriction/Traveling
Class (1 ~ 4) Override codes. Program 45 (8 ~ 9) overrides Program 44B
(1 ~ 4) if the same codes are used.
2-104
Z
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 46-2 ~ 4
TOLL RESTRICTION ALLOWED/DENIED AREA CODES ASSIGNED BY CLASS
P
S
4
6
H
S
H
SELECT = Class Number
Enter toll restriction class number 1 ~ 4.
Z
DATA = Area Codes
Enter or display area codes.
See Notes 3 and 4.
2, 3 or 4
Enter one of the following numbers:
2 = add to memory, 3 = delete from memory,4# = display
allowed codes in memory.
Class
1
Allowed
Area Codes
Denied
(Check one)
Class
2
Allowed
Area Codes
Denied
(Check one)
Class
3
Allowed
Area Codes
Denied
(Check one)
Class
4
Allowed
Area Codes
Denied
(Check one)
NOTES:
1. For more information, see the
instructions preceding the record
sheets.
2. Initialized data includes all area
codes in all classes.
3. A range of area codes
can be entered by pressing:
Low Area
Code
4. Several ranges or individual area codes may be entered by separating them with
a # button.
5. Tables with deny box checked do not represent memory. All area codes in
memory are allowed.
High Area
Code
Denotes end of string
2-105
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 46-6 ~ 8
TOLL RESTRICTION ALLOWED/DENIED OFFICE CODES ASSIGNED BY CLASS
P
S
4
6
H
S
H
SELECT = Class Number
Enter toll restriction class number 1 ~ 4.
Z
Z
DATA = Office Codes
Enter or display office codes.
See Notes 3 and 4.
6, 7 or 8
Enter one of the following numbers:
6 = add to memory, 7 = delete from memory,
8# = display allowed codes in memory.
Class
1
Allowed
Office Codes
Denied
(Check one)
Class
2
Allowed
Office Codes
Denied
(Check one)
Class
3
Allowed
Office Codes
Denied
(Check one)
Class
4
Allowed
Office Codes
Denied
(Check one)
NOTES:
1. For more information, see the
instructions preceding the record
sheets.
2. Initialized data allows all
office codes in all classes.
3. A range of office codes
can be entered by pressing:
Low Area
Code
4. Several ranges or individual office codes may be entered by separating them with
a # button.
5. Tables with the denied box checked do not represent memory. All Office Codes
in memory are allowed.
High Area
Code
Denotes end of string
2-106
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 46-10, -20, -30, -40
TOLL RESTRICTION CLASS 1 PARAMETERS
P
S
4
6
H
S
Y
Y
SELECT = YY
Enter the 2 digits on the dialpad which
represent the class number :
10 = Class 1
20 = Class 2
30 = Class 3
40 = Class 4
H
Z
Z
Button/LEDs
Light every button/LED marked
with an X in the table below.
Copy as required for each Class (1 ~ 4).
LED
X
LED ON
LED OFF
20
19
18
Table 8 Area/Office Exception
Not Selected
17
Table 7 Area/Office Exception
Not Selected
16
Table 6 Area/Office Exception
Not Selected
15
Table 5 Area/Office Exception
Not Selected
14
Table 4 Area/Office Exception
Not Selected
13
Table 3 Area/Office Exception
Not Selected
12
Table 2 Area/Office Exception
Not Selected
11
Table 1 Area/Office Exception
Not Selected
03
1 + A/C + 555/AC + 555 Allowed
Per Area Code Restriction
02
01 Restricted
Allowed
01
0 Restricted
Allowed
10
09
08
07
06
05
04
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data leaves all LEDs OFF.
2-107
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 47
TOLL RESTRICTION EXCEPTION OFFICE CODES ASSIGNED BY AREA CODES
(TABLES 1 AND 2)
P
S
4
7
H
SELECT = Exception Table 1 ~ 8
Enter the number of the
exception table, 1 ~ 8. A new
exception table is needed for
each area code with office
codes that are exceptions
to restriction.
S
1
H
S
H
Z
Z
DATA =
Enter or display office code(s).
See Notes 4 and 5.
AREA CODE =
Enter the area code.
See Note 3.
SELECT = Exception Table 1 ~ 8
Enter the number of the
exception table, 1 ~ 8 again.
2, 3 or 4
Enter 2 to add to the exception table.
Enter 3 to delete from the exception table.
Enter 4# to display the exception
table's office codes.
Record of Exception Office Codes (Data)
Exception Table (1 ~ 8)
Area Code
Record of Exception Office Codes (Data)
Exception Table (1 ~ 8)
Area Code
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns no office codes to tables.
3. Only one area code may be
entered per exception table.
4. To enter a range of office codes, key in:
5. Several ranges or individual office
codes may be entered by separating
them with a # button.
6. Copy as required,
maximum eight exception tables.
Denotes end of string
Low Office Code
High Office Code
2-108
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 48
STATION TOLL RESTRICTION CLASSIFICATION
P
S
4
8
H
S
SELECT = Logical Port Number(s)
Enter the port number(s) of the
station(s) being defined.
See Note 3 for entering a range.
H
DATA =
Digit Restriction Code 0 or 1
Enter 0 for no digit restriction.
Enter 1 for digit restriction.
Z
Z
Station Restriction Code (0 ~ 6)
Enter 0 for No Station Toll Restriction.
Enter 1 for Area Code Toll Restriction.
Enter 2 for Area Code Toll Restriction
and 0 or 1 as 1st or 2nd digit.
Enter 3 for Class 1 Toll Restriction.
Enter 4 for Class 2 Toll Restriction.
Enter 5 for Class 3 Toll Restriction.
Enter 6 for Class 4 Toll Restriction.
NOTE: Shaded areas apply to DK16 only
Logical
Port
Number
Digit
Restrict
Code
Station
Restrict
Code
00
01
02
03
04
05
06
07
08
09
104
11
12
13
14
15
16
17
18
19
204
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data reads "10" for all ports.
3. A range of ports may be entered:
Low port in range
High port in range
4. DK8, Port 10 and DK16, Port 20 assigns DISA CO lines to a Toll Restriction
Classification.
2-109
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
2-110
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAMMING PROCEDURES
LEAST COST ROUTING SYSTEM RECORD SECTION
Programs 50 ~ 56
2-111
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
2-112
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
LCR CO LINE PROGRAMING
1) Use Program 16 to assign CO lines in groups per the reference chart below.
CO Line Group Reference Chart
NOTE: Shaded areas apply to DK16 only
Line Group
CO Lines in
Group (1 ~ 8)
CO Line Type/Comments
1 (81)
2 (82)
3 (83)
4 (84)
5 (85)
6 (86)
7 (87)
8 (88)
2) Use Program 40 to allow CO lines access to stations using LCR for outgoing calls.
3) Use Program 41 to deny outgoing CO line access except for LCR access.
Important: Area code and office code structure must be defined by Program 45-1
(Toll Restriction Dial Plan) for LCR to work properly.
4) Use Program 45-1 to enable the dial plan that is appropriate for the area where LCR calls will originate.
PROGRAM 50-1
LCR PARAMETERS
P
S
5
0
H
S
1
SELECT = 1
LED
1
2
3
4
5
X
H
Z
Z
Press Button/LEDs for each LCR parameter.
LED On
Enable System LCR
Not Used
555 LDI Route Per Program 50-4
Dial Tone After LCR Access
Warning Tone Last Choice Route No.
LED Off
No LCR
Not Used
Per Area Code Table
Silent
No Warning Tone
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Program 40 denies CO line access via LCR and denies all other access methods.
3. Program 41 allows CO line access via LCR but denies all other outgoing access methods:
(CO line number 701 ~ 708, Pooled group 81 ~ 88, Line or Pooled Line Grp buttons).
4. Initialized data: All LEDs OFF.
5. To prevent Toll Restriction from being defeated because of K4RCU or QRCU time-out, Toll Restricted standard
telephones should be forced to dial outgoing calls via LCR.
2-113
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 50-2
LCR HOME AREA CODE
P
S
5
0
H
S
H
2
SELECT = 2
Z
Z
DATA = Home Area Code
Enter the local area code.
LCR Home Area Code
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Typically this code is entered in Program 51 table for the LCR route plan number defined for the local calls in
Program 50-5.
3. Initialized data leaves the home area code blank.
PROGRAM 50-31 ~ 35
LCR SPECIAL CODES
P
S
5
0
H
S
H
SELECT = 31 ~ 35
Enter 31 ~ 35 to indicate
the special code.
Special Code
Z
DATA = Special Code
Enter the code from the table below.
Examples
31
1-411
32
911
33
611
34
35
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data leaves all codes blank.
3. Press Button/LED 01 to erase data and leave blank.
4. These calls follow the local call route defined in Program 50-5.
2-114
Z
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 50-4
LCR LONG DISTANCE INFORMATION (LDI) PLAN NUMBER
P
S
5
0
H
S
4
SELECT = 4
H
Z
Z
DATA = LDI Route Plan (1 ~ 8)
Identify the LDI Route Plan
by entering 1 ~ 8.
LDI Plan Number:
(1 ~ 8)
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns LDI Plan Number 8.
3. Typically, LDI Plan Number = Local Call Plan Number.
PROGRAM 50-5
LCR LOCAL CALL ROUTE PLAN NUMBER
P
S
5
0
H
S
5
H
SELECT = 5
Z
Z
DATA = Local Route Plan (1 ~ 8)
Identify the Local Route Plan
by entering 1 ~ 8.
Local Call Plan Number:
(1 ~ 8)
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns Plan 8 to be the local call plan.
3. The local plan handles special codes and operator calls.
PROGRAM 50-6
LCR DIAL ZERO TIMEOUT
P
S
5
0
H
S
6
SELECT = 6
H
Z
DATA = Timeout Value
Enter a timeout value from
04 ~ 10 seconds long.
Dial Zero Timeout:
(04 ~ 10 seconds)
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns an LCR Dial Zero Timeout value of 06.
3. This value determines pause time before sending a call on to an operator, etc.
2-115
Z
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 51
LCR AREA CODES
P
S
5
1
H
SELECT = LCR
Plan Number (1 ~ 8)
LCR
Plan
1
DATA = Area Code(s)
LCR
Plan
S
H
Action Code:
Enter 2 to add code to table.
Enter 3 to delete code from table.
Enter 4# to display codes in table.
2
DATA = Area Code(s)
Z
Z
DATA = Area Code(s)
(3 digits)
LCR
3
Plan
DATA = Area Code(s)
LCR
4
Plan
DATA = Area Code(s)
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data leaves Tables 1 ~ 7 blank; all codes (000 ~ 999) are initialized in Table 8.
3. To enter a range of Area Codes, press:
Low Area
Code
High Area
Code
Denotes end of string
4. Several ranges or individual codes can be expressed at once by separating them with a # button
2-116
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 51
LCR AREA CODES
P
S
5
1
H
SELECT = LCR
Plan Number (1 ~ 8)
LCR
Plan
5
DATA = Area Code(s)
LCR
Plan
S
H
Action Code:
Enter 2 to add code to table.
Enter 3 to delete code from table.
Enter 4# to display codes in table.
6
DATA = Area Code(s)
Z
Z
DATA = Area Code(s)
(3 digits)
LCR
7
Plan
DATA = Area Code(s)
LCR
8
Plan
DATA = Area Code(s)
000 ~ 999
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data leaves Tables 1 ~ 7 blank; all codes (000 ~ 999) are initialized in Table 8.
3. To enter a range of Area Codes, press:
Low Area
Code
High Area
Code
Denotes end of string
4. Several ranges or individual codes can be expressed at once by separating them with a # button.
2-117
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 52
LCR OFFICE CODE EXCEPTIONS FOR SPECIFIED AREA CODE
To assign Office Code Exception Table (1 ~ 4) to an LCR Plan:
more data
P
S
5
2
H
S
H
SELECT = Office Code
Exception Table (1-8)
Action Code Function
Z
Z
DATA = (See below)
Action Code
Action Codes
DATA =
Assign Exception Table to LCR Plan
0
Assign Area Code to LCR Plan
1
3-digit Area Code
Add Office Codes to Exception Table
2
3-digit Office Code
Delete Office Codes from Exception Table
3
3-digit Office Code
Display Office Codes in Exception Table
4
Office Code Exception Table
1
2
3
for Area Code
Office Codes:
for Area Code
Assign to LCR Route Plan Number
Office Code Exception Table
4
3-digit Office Code
Office Codes:
Assign to LCR Route Plan Number
Office Code Exception Table
# more #
for Area Code
Assign to LCR Route Plan Number
Office Code Exception Table
LCR Plan 1 ~ 8
Office Codes:
for Area Code
Assign to LCR Route Plan Number
Office Codes:
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data leaves all codes blank.
3. To enter a range of office codes, press:
Low Area
Code
High Area
Code
Denotes end of string
4. Several ranges or individual codes can be expressed at once by separating them with a # button.
5. Copy as required, maximum eight Office Code Exception Tables.
2-118
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 52
LCR OFFICE CODE EXCEPTIONS FOR SPECIFIED AREA CODE
To assign Office Code Exception Table (5 ~ 8) to an LCR Plan:
more data
P
S
5
2
H
S
H
SELECT = Office Code
Exception Table (1-8)
Action Code Function
Z
Z
DATA = (See below)
Action Code
Action Codes
DATA =
Assign Exception Table to LCR Plan
0
Assign Area Code to LCR Plan
1
3-digit Area Code
Add Office Codes to Exception Table
2
3-digit Office Code
Delete Office Codes from Exception Table
3
3-digit Office Code
Display Office Codes in Exception Table
4
Office Code Exception Table
5
6
7
for Area Code
Office Codes:
for Area Code
Assign to LCR Route Plan Number
Office Code Exception Table
8
3-digit Office Code
Office Codes:
Assign to LCR Route Plan Number
Office Code Exception Table
# more #
for Area Code
Assign to LCR Route Plan Number
Office Code Exception Table
LCR Plan 1 ~ 8
Office Codes:
for Area Code
Assign to LCR Route Plan Number
Office Codes:
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data leaves all codes blank.
3. To enter a range of office codes, press:
Low Area
Code
High Area
Code
Denotes end of string
4. Several ranges or individual codes can be expressed at once by separating them with a # button.
2-119
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 53
LCR SCHEDULE ASSIGNMENTS
FOR LCR PLAN NO. 1 AND 2
more data
P
S
5
3
H
S
H
SELECT =
SELECT
Start TM
Schedule (1 ~ 3)
Plan 1
1
1
0
1
2
0
1
3
0
SELECT
Start TM
Schedule (1 ~ 3)
Plan 2
H M M
Action Code
1
Schedule 2
Route Choices
For Plan 1
Schedule 3
Route Choices
For Plan 1
LCR Plan
Schedule (1 ~ 3)
1
1
0
2
2
0
2
3
0
SELECT DATA (Route Choices)
Schedule 1
Route Choices
For Plan 2
2
1
1
2
1
2
2
1
3
1
1
2
1
1
3
1
1
4
2
1
4
1
2
1
2
2
1
1
2
2
2
2
2
1
2
3
2
2
3
1
2
4
2
2
4
1
3
1
2
3
1
2
3
2
2
3
3
2
3
4
3
2
1
3
3
1
3
4
Schedule 2
Route Choices
For Plan 2
Schedule 3
Route Choices
For Plan 2
1st 2nd 3rd Last
H M M
( HH = 00 ~ 23
MM = 00 ~ 59)
Action Code
1
1
Start TM
H
Schedule (1 ~ 3)
SELECT DATA (Route Choices)
Schedule 1
Route Choices
For Plan 1
2
LCR Plan
( HH = 00 ~ 23
MM = 00 ~ 59)
Schedule (1 ~ 3)
Z
Start TM or DATA
Start TM
H
LCR Plan
Z
LCR Plan
1st 2nd 3rd Last
Schedule (1 ~ 3)
(Route Definition
(Route Definition
LCR Station
LCR Station
No's (1 ~ 4)
No's (1 ~ 4)
Group No. (1 ~ 4)
Group No. (1 ~ 4)
From Program 54 )
From Program 54 )
(see Program 56 )
(see Program 56 )
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns starting time as 0000 and Route Definitions as blank for all schedules.
3. If schedules 1 & 2 start at the same time, then Time of Day schedule change does not occur, and data only needs
to be entered for schedule 1.
4. Press Button/LED 01 to erase data (LED does not light).
2-120
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 53
LCR SCHEDULE ASSIGNMENTS
FOR LCR PLAN NO. 3 AND 4
more data
P
S
5
3
H
S
H
SELECT =
SELECT
Start TM
Schedule (1 ~ 3)
Plan 3
3
1
0
3
2
0
3
3
0
Action Code
Schedule 1
Route Choices
For Plan 3
Schedule 2
Route Choices
For Plan 3
Schedule 3
Route Choices
For Plan 3
LCR Plan
SELECT
Start TM
Schedule (1 ~ 3)
Plan 4
H M M
1
0
4
2
0
4
3
0
Start TM
H
H M M
( HH = 00 ~ 23
MM = 00 ~ 59)
Schedule (1 ~ 3)
Action Code
SELECT DATA (Route Choices)
SELECT DATA (Route Choices)
3
1
1
4
1
1
3
1
2
4
1
2
3
1
3
4
1
3
3
1
4
4
1
4
3
2
1
4
2
1
4
2
2
4
2
3
Schedule 1
Route Choices
For Plan 4
Schedule 2
Route Choices
For Plan 4
3
2
2
3
2
3
3
2
4
4
2
4
3
3
1
4
3
1
3
3
2
4
3
2
3
3
3
4
3
3
3
3
4
4
3
4
Schedule 3
Route Choices
For Plan 4
LCR Plan
1st 2nd 3rd Last
Schedule (1 ~ 3)
LCR Station
Group No. (1 ~ 4)
(see Program 56 )
4
LCR Plan
( HH = 00 ~ 23
MM = 00 ~ 59)
Schedule (1 ~ 3)
Z
Start TM or DATA
Start TM
H
LCR Plan
Z
1st 2nd 3rd Last
Schedule (1 ~ 3)
(Route Definition
No's (1 ~ 4)
From Program 54 )
LCR Station
Group No. (1 ~ 4)
(see Program 56 )
(Route Definition
No's (1 ~ 4)
From Program 54 )
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns starting time as 0000 and Route Definitions as blank for all schedules.
3. If schedules 1 & 2 start at the same time, then Time of Day schedule change does not occur, and data only needs
to be entered for schedule 1.
4. Press Button/LED 01 to erase data (LED does not light).
2-121
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 53
LCR SCHEDULE ASSIGNMENTS
FOR LCR PLAN NO. 5 AND 6
more data
P
S
5
3
H
S
H
SELECT =
SELECT
Start TM
Schedule (1 ~ 3)
Plan 5
5
1
0
5
2
0
5
3
0
SELECT
Start TM
Schedule (1 ~ 3)
Plan 6
H M M
Action Code
5
Schedule 2
Route Choices
For Plan 5
Schedule 3
Route Choices
For Plan 5
LCR Plan
1
1
2
5
1
3
5
1
4
5
2
1
6
2
0
6
3
0
Schedule 2
Route Choices
For Plan 6
H
H M M
( HH = 00 ~ 23
MM = 00 ~ 59)
6
1
1
6
1
2
6
1
3
6
1
4
6
2
1
6
2
2
6
2
3
5
2
2
5
2
3
5
2
4
6
2
4
5
3
1
6
3
1
5
3
2
6
3
2
5
3
3
6
3
3
5
3
4
6
3
4
Schedule 3
Route Choices
For Plan 6
LCR Plan
1st 2nd 3rd Last
Start TM
SELECT DATA (Route Choices)
Schedule 1
Route Choices
For Plan 6
Schedule (1 ~ 3)
LCR Station
Group No. (1 ~ 4)
(see Program 56 )
0
Action Code
1
5
1
Schedule (1 ~ 3)
SELECT DATA (Route Choices)
Schedule 1
Route Choices
For Plan 5
6
LCR Plan
( HH = 00 ~ 23
MM = 00 ~ 59)
Schedule (1 ~ 3)
Z
Start TM or DATA
Start TM
H
LCR Plan
Z
1st 2nd 3rd Last
Schedule (1 ~ 3)
(Route Definition
No's (1 ~ 4)
From Program 54 )
LCR Station
Group No. (1 ~ 4)
(see Program 56 )
(Route Definition
No's (1 ~ 4)
From Program 54 )
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns starting time as 0000 and Route Definitions as blank for all schedules.
3. If schedules 1 & 2 start at the same time, then Time of Day schedule change does not occur, and data only needs
to be entered for schedule 1.
4. Press Button/LED 01 to erase data (LED does not light).
2-122
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 53
LCR SCHEDULE ASSIGNMENTS
FOR LCR PLAN NO. 7 AND 8
more data
P
S
5
3
H
S
H
SELECT =
SELECT
Start TM
Schedule (1 ~ 3)
Plan 7
7
1
0
7
2
0
7
3
0
SELECT
Start TM
Schedule (1 ~ 3)
Plan 8
H M M
Action Code
7
Schedule 2
Route Choices
For Plan 7
Schedule 3
Route Choices
For Plan 7
LCR Plan
1
1
2
7
1
3
7
1
4
7
2
1
8
2
0
8
3
0
Schedule 2
Route Choices
For Plan 8
H
H M M
( HH = 00 ~ 23
MM = 00 ~ 59)
8
1
1
8
1
2
8
1
3
8
1
4
8
2
1
8
2
2
8
2
3
7
2
2
7
2
3
7
2
4
8
2
4
7
3
1
8
3
1
7
3
2
8
3
2
7
3
3
8
3
3
7
3
4
8
3
4
Schedule 3
Route Choices
For Plan 8
1st 2nd 3rd Last
Start TM
SELECT DATA (Route Choices)
Schedule 1
Route Choices
For Plan 8
Schedule (1 ~ 3)
LCR Station
Group No. (1 ~ 4)
(see Program 56 )
0
Action Code
1
7
1
Schedule (1 ~ 3)
SELECT DATA (Route Choices)
Schedule 1
Route Choices
For Plan 7
8
LCR Plan
( HH = 00 ~ 23
MM = 00 ~ 59)
Schedule (1 ~ 3)
Z
Start TM or DATA
Start TM
H
LCR Plan
Z
LCR Plan
1st 2nd 3rd Last
Schedule (1 ~ 3)
(Route Definition
No's (1 ~ 4)
From Program 54 )
LCR Station
Group No. (1 ~ 4)
(see Program 56 )
(Route Definition
No's (1 ~ 4)
From Program 54 )
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns starting time as 0000 and Route Definitions as blank for all schedules.
3. If schedules 1 & 2 start at the same time, then Time of Day schedule change does not occur, and data only needs
to be entered for schedule 1.
4. Press Button/LED 01 to erase data (LED does not light).
2-123
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 54
LCR ROUTE DEFINITION TABLES (1 ~ 4)
P
S
5
4
H
S
H
SELECT =
Z
Z
CODE =
Enter Data
SELECT =
Route Definition Table
for LCR Plan 1
Route Definition Table
for LCR Plan 2
Route Definition Table
for LCR Plan 3
Route Definition Table
for LCR Plan 4
CODE = CO line group and
modified digits table
1
1
1
2
1
3
1
4
2
1
2
2
2
3
2
4
3
1
3
2
3
3
3
4
4
1
4
2
4
3
4
4
LCR Plan No. (1 ~ 4)
Modified digits table 1 ~ 6,
see Program 55
Route Definition Number
CO line group 1 ~ 8,
see Program 16
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data is “11”.
2-124
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 54
LCR ROUTE DEFINITION TABLES (5 ~ 8)
P
S
5
4
H
S
H
SELECT =
Z
Z
CODE =
Enter Data
SELECT =
Route Definition Table
for LCR Plan 5
Route Definition Table
for LCR Plan 6
Route Definition Table
for LCR Plan 7
Route Definition Table
for LCR Plan 8
CODE = CO line group and
modified digits table
5
1
5
2
5
3
5
4
6
1
6
2
6
3
6
4
7
1
7
2
7
3
7
4
8
1
8
2
8
3
8
4
LCR Plan No. (5 ~ 8)
Modified digits table 1 ~ 6,
see Program 55
Route Definition Number
CO line group 1 ~ 8,
see Program 16
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data is “11”.
2-125
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 55
LCR MODIFIED DIGITS TABLES
PROGRAM 55-0 LCR MODIFIED DIGITS – DELETE FROM FRONT
P
S
5
5
H
S
0
SELECT = Modified Digits
Table 1 ~ 6 (six available)
H
Z
Z
FIGURE = Quantity of Digits
(00 ~ 10) to be deleted.
PROGRAM 55-1 and 2 LCR MODIFIED DIGITS – ADD
P
S
5
5
H
S
H
SELECT = Modified Digits Table (1 ~ 6)
Enter 1 to add digits in front of number dialed
Enter 2 to add digits at end of number dialed
Z
Z
CODE = Digits added (up to 22). Enter the
digits to be added. Pauses may be
coded as described in the pause
entry reference table below.
PAUSE ENTRY REFERENCE
(Program 55-1, 55-2)
DELETE DIGITS TABLES
Key/LED Pause (Seconds) Record Entry Special Keys:
Table No. Quantity of Digits
1
08
07
06
05
2
3
4
5
6
04
03
02
01
Quantity 10 Max. (00 ~ 10)
16
14
P8
P7
12
10
P6
P5
8
6
4
P4
P3
P2
2
P1
Key/LED
11 – Clear
10 – Convert DP to DTMF
ADD DIGIT TABLES
Add to FRONT of Dialed Number ( Program 55-1)
Table No. 1
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 Comments
2
3
4
5
6
Add to END of Dialed Number (Program 55-2)
Table No. 1
1
2
3
4
5
6
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 Comments
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data leaves all tables blank except Delete Digits, which are all 00.
2-126
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
PROGRAM 56
LCR STATION GROUP ASSIGNMENT
P
S
5
6
H
S
H
SELECT = Logical Port number(s)
Enter port numbers of stations being assigned.
See Note 3 for entering a range of ports.
LCR Station
Group No. (1 ~ 4)
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data assigns all stations to group 1.
3. To enter a range of ports, press:
Low port
High port
4. Refer to Program 53.
2-127
Z
Enter LCR station Group (1 ~ 4)
NOTE: Shaded areas apply to DK16 only
Logical
Port
Number
Z
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
This table below shows the program options for stations and CO lines for verified, forced and voluntary account code
dialing.
TABLE 2-B
ACCOUNT CODE PROGRAM OPTION MATRIX
Account Code
Program Options
Station
CO Line
Verified
Program 30
LED 14
Forced
Program 30
LED 08
Forced
Program 15-7
CO LED
Verified (Forced)
On
On
On
Verified (Voluntary)
On
On
Off
Verified (Voluntary)
On
Off
On
Verified (Voluntary)
On
Off
Off
Not Verified (Forced)
Off
On
On
Not Verified (Voluntary)
Off
On
Off
Not Verified (Voluntary)
Off
Off
On
Not Verified (Voluntary)
Off
Off
Off
Account Code
Dial Plan
2-128
System
Initialization
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
TABLE 2-C
OVERRIDE OPTION MATRIX
Station A May Override
Station B 1
Privacy
Override
Station A
Options
Privacy
Override Block
Station B
Options
3
Station B
Button Options (Program 39)
Privacy
on Line 2
Button
Privacy
Release 2
Button
Privacy
Program 30
LED 19
Yes
No
Off
Off
Off
Off
Yes
Yes
Yes
No
Off
Off
Off
Off
Off
On
On
Off
Yes
No
No
No
No
Yes
Yes
Yes
Yes
Yes
No
Off
Off
Off
On
On
Off
On
Off
Yes
No
Off
Off
On
On
Off
On
On
Off
Yes
Yes
Off
On
On
Off
On
Off
On
Off
Yes
No
Yes
No
Yes
No
Yes
On
On
On
On
On
On
On
Off
Off
Off
On
On
On
On
Off
On
On
Off
Off
On
On
On
Off
On
Off
On
Off
On
Executive 3
No
No
No
No
Program 31
LED 18
NOTES:
1. Station “A” attempts to override (Executive or Privacy) Station “B”.
2. Normally, either the Privacy on Line or Privacy Release button, not both, is assigned to a telephone (Program
39) depending on how it should operate with Privacy Override.
3. Program 30, Button/LED 18 is turned ON for Station A, allowing Station A to have Executive Override to
Station B for some possibilities in this table. If Program 30, LED 18 is OFF for Station A, then it can never
Executive Override any station.
2-129
PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
2-130

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project