Billion | BiPAC 710C2 | User`s manual | Billion BiPAC 710C2 User`s manual

BIPAC-711C2 / 710C2
ADSL Modem / Router
Quick Start Guide
Billion BIPAC – 711C2 / 710C2 – ADSL Modem / Router
For more detailed instructions on configuring and using
the ADSL Modem/Router, please refer to the on-line
manual.
Package Contents
BIPAC-711C2 / 710C2 ADSL Router
CD-ROM containing the online manual
RJ-11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
One USB cable (for 711C2 only)
AC-DC power adapter (12VDC, 1A)
This Quick Start Guide
Do not use the BIPAC-711C2 / 710C2 in high humidity or high
temperatures.
Do not use the same power source for the BIPAC-711C2 / 710C2
as other equipment.
Warning
Do not open or repair the case yourself. If the BIPAC-711C2 /
710C2 is too hot, turn off the power immediately and have it
repaired at a qualified service center.
Place the BIPAC-711C2 / 710C2 on a stable surface.
Only use the power adapter that comes with the package. Using
a different voltage rating power adaptor may damage the router.
Attention
1
Quick Start Guide
The Front LEDs
5
7
LED
3
4
1
2
Meaning
1
PWR
Lit green when power adapter is connected.
2
SYS
When lit, it indicates that the device is working properly.
3
USB
When this LED is lit, it indicates that the USB port is connected to
the PC and working properly.
4
LNK
Lit green when the LAN link is connected.
5
COL
Flashes green when collision happens
7
ADSL
When lit, it indicates that the ADSL (Line) port is connected to the
DSLAM and working properly.
The difference between BIPAC-711C2 and 710C2 is that BIPAC-710C2
does not have USB port; the rest functions are the same as BIPAC711C2.
2
Billion BIPAC – 711C2 / 710C2 – ADSL Modem / Router
The Rear Ports
6
4
3
5
Port
1
2
Meaning
1
Power Switch
Power ON/OFF switch
2
PWR
Connect the supplied power adapter to this jack.
3
4
5
6
(RJ-45 connector)
Connect the supplied crossover cable to this port when
connecting to a NIC (Network Interface card) in PC.
Connect an UTP Ethernet cable to this port when connecting to a
LAN such as an office or home network.
RESET
Press it to restore the factory default setting back
USB
Connect the supplied USB cable to this port when connecting to
the PC
LAN
(USB connector)
LINE
(RJ-11 connector)
Connect the supplied RJ-11 cable to this port when connecting to
the ADSL
BIPAC-710C2 does not have USB port.
3
Quick Start Guide
Connecting Your ADSL Modem/Router
Through Ethernet Port
1. Connect the Router to a LAN (Local Area Network) and the ADSL/telephone (LINE) network.
2. Power on the device.
3. Make sure the PWR, SYS and LAN LEDs are lit steadily
4. Follow the “Configuring the Network Properties on a PC” section on page 8 to modify the
network settings
Through USB Port (for BIPAC-711C2 only)
1. Connect the USB cable to the USB port of the device and connect the other end to the PC.
Also connect the device to the ADSL/telephone network.
2. Power on the device
3. Ensure the Power and LAN LEDs are lit
4. Follow the “Installing the USB Driver on a PC” section on page 5 to setup this device.
4
Billion BIPAC – 711C2 / 710C2 – ADSL Modem / Router
Installing the USB Driver on a PC (for BIPAC-711C2 only)
This section is described based on Windows XP. For other Operating
Systems such as Windows 2000/Me/98, please refer to the on-line
manual for more detailed instructions.
If you connect the device through USB port instead of Ethernet port, for the first time the USB
cable is connected to the PC, Windows will automatically detect the device. Follow the steps to
install the USB driver.
1. When Windows tells you that the new device has been detected, select “Install from a list or
specific location” and click “Next >”.
2. Insert the installation CD into the CD-ROM drive. Check “Search removable media” and click
“Next >”. Then, it takes seconds to search and install the software.
5
Quick Start Guide
3. When windows titled “Hardware Installation” or “Software Installation” appear, press
“Continue Anyway” to go on.
4. Then, click “Finish”
5. After a few moments, Windows will show the new device, USB ADSL Adapter, has been
detected. Select “Install from a list or specific location”. Click “Next >”.
6
Billion BIPAC – 711C2 / 710C2 – ADSL Modem / Router
6. Click “Next >” when the following figure appears.
7. When windows titled “Hardware Installation” appears, press “Continue Anyway”. Then, click
“Finish” to end installation.
8. After installing the driver, follow the next section to configure the network properties on the PC.
7
Quick Start Guide
Configuring PC in Windows XP
1. Go to Start / Control Panel (in Classic
View). In the Control Panel, double-click on
Network Connections
2. Double-click Local Area Connection.
3. In the Local Area Connection Status
window, click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
8
Billion BIPAC-711C2/710C2 ADSL Modem / Router
Configuring PC in Windows 2000
1. Go to Start / Settings / Control Panel. In the
Control Panel, double-click on Network and
Dial-up Connections.
2. Double-click Local Area Connection.
3. In the Local Area Connection Status window
click Properties.
4. Select Internet Protocol (TCP/IP) and click
Properties.
5. Select the Obtain an IP address
automatically and the Obtain DNS server
address automatically radio buttons.
6. Click OK to finish the configuration.
9
Quick Start Guide
Configuring PC in Windows 98/Me
1. Go to Start / Settings / Control Panel. In the
Control Panel, double-click on Network and
choose the Configuration tab.
2. Select TCP/IP ->
NE2000 Compatible, or the name of your
Network Interface Card (NIC) in your PC.
3. Select the Obtain an IP address
automatically radio button.
4. Then select the DNS Configuration tab.
5. Select the Disable DNS radio button and click
OK to finish the configuration.
10
Billion BIPAC-711C2/710C2 ADSL Modem / Router
Configuring PC in Windows NT4.0
1. Go to Start / Settings / Control Panel. In the
Control Panel, double-click on Network and
choose the Protocols tab.
2. Select TCP/IP Protocol and click Properties.
3. Select the Obtain an IP address from a
DHCP server radio button and click OK.
11
Quick Start Guide
Configuring Your ADSL Modem/Router
To configure this device, you must have IE 5.0 /
Netscape 4.5 or above installed
Verifying Your Local Network Connection with the Device
To see if this ADSL Router is
visible on the local network, go
to Start / Run. In the Run dialog
box, type “ping 192.168.1.254”
then press OK.
A command prompt window will
pop out.
If your ping is
successful which means your
local network is able to reach to
the device, then the command
prompt window will close up
automatically.
Connection fails, when you see
“Request timed out” in the
command prompt window. You
may need to check your set up.
12
Billion BIPAC-711C2/710C2 ADSL Modem / Router
Connecting to the Router
Open the web browser and type
http://192.168.1.254 in the
browser’s address box. This
number is the default IP address
for this router. Press Enter.
A user name and password
window will appear. The default
User Name and Password are
“admin” and” admin”. Press
OK to logon to the router
Product Support and Contact Information
Most problems can be solved by referring to the Troubleshooting section in the User’s
Manual. If you cannot resolve the problem with the Troubleshooting chapter, please contact
the dealer where you purchased this product.
Contact Billion
AUSTRALIA
http://www.billion.com.au/
Hotline: 1300 139 159, 7 days a week.
©2004 Billion Electric Co., Ltd. PC Range P/L. All Rights Reserved.
WORLDWIDE
http://www.billion.com/
Mac OS is a registered Trademark of Apple Computer, Inc.
Windows 98, Windows NT, Windows 2000, Windows Me and Windows XP are registered Trademarks of Microsoft
Corporation.
13
Download PDF