A-Gas Solvokane
A-Gas Solvokane
A-Gas (Australia) Pty Ltd
Chemwatch Hazard Alert Code: 2
Issue Date: 06/09/2013
Print Date: 13/02/2014
Initial Date: Not Available
S.Local.AUS.EN
Chemwatch: 4838-93
Version No: 4.1.1.1
Material Safety Data Sheet according to NOHSC and ADG requirements
SECTION 1 IDENTIFICATION OF THE SUBSTANCE / MIXTURE AND OF THE COMPANY / UNDERTAKING
Product Identifier
Product name
Chemical Name
Synonyms
A-Gas Solvokane
Not Applicable
Not Available
Proper shipping name
Not Applicable
Chemical formula
Not Applicable
Other means of identification
CAS number
Not Available
Not Applicable
Relevant identified uses of the substance or mixture and uses advised against
Relevant identified uses
The use of a quantity of material in an unventilated or confined space may result in increased exposure and an irritating atmosphere developing.
Before starting consider control of exposure by mechanical ventilation.
, Aerosol propellants; Cleaning agent; Detergent; Electrical industry; Electronic industry.
Details of the supplier of the safety data sheet
Registered company name
Address
A-Gas (Australia) Pty Ltd
9-11 Oxford Road Laverton North VIC 3026
Australia
Telephone
[+61] (0) 3 93689222
Fax
[+61] (0) 3 93689233
Website
Email
www.agas.com
[email protected]
Emergency telephone number
Association / Organisation
Not Available
Emergency telephone numbers
TOLL: [+61] 1800 024 973
Other emergency telephone numbers
TOLL: [+61] 1800 024 973
CHEMWATCH EMERGENCY RESPONSE
Primary Number
Alternative Number 1
Alternative Number 2
1800 039 008
+612 9186 1132
Not Available
Once connected and if the message is not in your prefered language then please dial 01
SECTION 2 HAZARDS IDENTIFICATION
Classification of the substance or mixture
HAZARDOUS SUBSTANCE. NON-DANGEROUS GOODS. According to the Criteria of NOHSC, and the ADG Code.
CHEMWATCH HAZARD RATINGS
Min
Flammability
Toxicity
Body Contact
Reactivity
Chronic
Max
1
2
2
2
2
0 = Minimum
1 = Low
2 = Moderate
3 = High
4 = Extreme
Poisons Schedule
Risk Phrases [1]
None
R20/22
Harmful by inhalation and if swallowed.
R52/53
Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
Continued...
Chemwatch: 4838-93
Version No: 4.1.1.1
Legend:
GHS Classification [1]
Legend:
Page 2 of 9
Issue Date: 06/09/2013
A-Gas Solvokane
Print Date: 13/02/2014
R67
Vapours may cause drowsiness and dizziness.
R04
Forms very sensitive explosive metallic compounds.
R19
May form explosive peroxides.
R30
Can become highly flammable in use.
1. Classified by Chemwatch; 2. Classification drawn from HSIS ; 3. Classification drawn from EC Directive 1272/2008 - Annex VI
Acute Toxicity (Oral) Category 4, Acute Toxicity (Inhalation) Category 4, STOT - SE (Narcosis) Category 3, Chronic Aquatic Hazard Category 3
1. Classified by Chemwatch; 2. Classification drawn from HSIS ; 3. Classification drawn from EC Directive 1272/2008 - Annex VI
Label elements
GHS label elements
SIGNAL WORD
WARNING
Hazard statement(s)
H302
Harmful if swallowed
H332
Harmful if inhaled
H336
May cause drowsiness or dizziness
H412
Harmful to aquatic life with long lasting effects
AUH019
May form explosive peroxides
Precautionary statement(s): Prevention
P271
Use only outdoors or in a well-ventilated area.
P261
Avoid breathing dust/fume/gas/mist/vapours/spray.
P264
Wash all exposed external body areas thoroughly after handling.
P270
Do not eat, drink or smoke when using this product.
P273
Avoid release to the environment.
Precautionary statement(s): Response
P301+P312
IF SWALLOWED: Call a POISON CENTER/doctor/physician/first aider/if you feel unwell.
P304+P340
IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P330
Rinse mouth.
Precautionary statement(s): Storage
P405
P403+P233
Store locked up.
Store in a well-ventilated place. Keep container tightly closed.
Precautionary statement(s): Disposal
P501
Dispose of contents/container to authorised chemical landfill or if organic to high temperature incineration
Label elements
Relevant risk statements are found in section 2
Indication(s) of danger
Xn
SAFETY ADVICE
S03
Keep in a cool place.
S07
Keep container tightly closed.
S09
Keep container in a well ventilated place.
S13
Keep away from food, drink and animal feeding stuffs.
S18
Handle and open container with care.
S23
Do not breathe gas/fumes/vapour/spray.
S29
Do not empty into drains.
S35
This material and its container must be disposed of in a safe way.
S36
Wear suitable protective clothing.
Continued...
Chemwatch: 4838-93
Version No: 4.1.1.1
S37
Wear suitable gloves.
Page 3 of 9
Issue Date: 06/09/2013
A-Gas Solvokane
Print Date: 13/02/2014
S40
To clean the floor and all objects contaminated by this material, use water and detergent.
S46
If swallowed, seek medical advice immediately and show this container or label.
S51
Use only in well ventilated areas.
S56
Dispose of this material and its container at hazardous or special waste collection point.
S57
Use appropriate container to avoid environmental contamination.
Other hazards
May produce discomfort of the eyes, respiratory tract and skin*.
Cumulative effects may result following exposure*.
Repeated exposure potentially causes skin dryness and cracking*.
Limited evidence of a carcinogenic effect*.
SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTS
Substances
See section below for composition of Mixtures
Mixtures
CAS No
%[weight]
Name
406-58-6
>65
365 mfc
156-60-5
<35
trans-acetylene dichloride
SECTION 4 FIRST AID MEASURES
Description of first aid measures
Eye Contact
Skin Contact
Inhalation
If this product comes in contact with the eyes:
Wash out immediately with fresh running water.
Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionally lifting the upper and
lower lids.
Seek medical attention without delay; if pain persists or recurs seek medical attention.
Removal of contact lenses after an eye injury should only be undertaken by skilled personnel.
If skin contact occurs:
Immediately remove all contaminated clothing, including footwear.
Flush skin and hair with running water (and soap if available).
Seek medical attention in event of irritation.
If fumes or combustion products are inhaled remove from contaminated area.
Lay patient down. Keep warm and rested.
Prostheses such as false teeth, which may block airway, should be removed, where possible, prior to initiating first aid procedures.
Apply artificial respiration if not breathing, preferably with a demand valve resuscitator, bag-valve mask device, or pocket mask as trained.
Perform CPR if necessary.
Transport to hospital, or doctor.
IF SWALLOWED, REFER FOR MEDICAL ATTENTION, WHERE POSSIBLE, WITHOUT DELAY.
For advice, contact a Poisons Information Centre or a doctor.
Urgent hospital treatment is likely to be needed.
In the mean time, qualified first-aid personnel should treat the patient following observation and employing supportive measures as indicated
by the patient's condition.
If the services of a medical officer or medical doctor are readily available, the patient should be placed in his/her care and a copy of the
MSDS should be provided. Further action will be the responsibility of the medical specialist.
If medical attention is not available on the worksite or surroundings send the patient to a hospital together with a copy of the MSDS.
Ingestion
Where medical attention is not immediately available or where the patient is more than 15 minutes from a hospital or unless
instructed otherwise:
INDUCE vomiting with fingers down the back of the throat, ONLY IF CONSCIOUS. Lean patient forward or place on left side (head-down
position, if possible) to maintain open airway and prevent aspiration.
NOTE: Wear a protective glove when inducing vomiting by mechanical means.
Avoid giving milk or oils.
Avoid giving alcohol.
Indication of any immediate medical attention and special treatment needed
·
·
·
·
·
for poisons (where specific treatment regime is absent):
-------------------------------------------------------------BASIC TREATMENT
-------------------------------------------------------------Establish a patent airway with suction where necessary.
Watch for signs of respiratory insufficiency and assist ventilation as necessary.
Administer oxygen by non-rebreather mask at 10 to 15 L/min.
Monitor and treat, where necessary, for pulmonary oedema.
Monitor and treat, where necessary, for shock.
Continued...
Chemwatch: 4838-93
Version No: 4.1.1.1
·
·
·
·
·
·
·
·
·
·
Page 4 of 9
Issue Date: 06/09/2013
A-Gas Solvokane
Print Date: 13/02/2014
Anticipate seizures .
DO NOT use emetics. Where ingestion is suspected rinse mouth and give up to 200 ml water (5 ml/kg recommended) for dilution where patient
is able to swallow, has a strong gag reflex and does not drool.
-------------------------------------------------------------ADVANCED TREATMENT
-------------------------------------------------------------Consider orotracheal or nasotracheal intubation for airway control in unconscious patient or where respiratory arrest has occurred.
Positive-pressure ventilation using a bag-valve mask might be of use.
Monitor and treat, where necessary, for arrhythmias.
Start an IV D5W TKO. If signs of hypovolaemia are present use lactated Ringers solution. Fluid overload might create complications.
Drug therapy should be considered for pulmonary oedema.
Hypotension with signs of hypovolaemia requires the cautious administration of fluids. Fluid overload might create complications.
Treat seizures with diazepam.
Proparacaine hydrochloride should be used to assist eye irrigation.
BRONSTEIN, A.C. and CURRANCE, P.L.
EMERGENCY CARE FOR HAZARDOUS MATERIALS EXPOSURE: 2nd Ed. 1994
Treat symptomatically.
for intoxication due to Freons/ Halons;
A: Emergency and Supportive Measures
Maintain an open airway and assist ventilation if necessary
Treat coma and arrhythmias if they occur. Avoid (adrenaline) epinephrine or other sympathomimetic amines that may precipitate ventricular
arrhythmias. Tachyarrhythmias caused by increased myocardial sensitisation may be treated with propranolol, 1-2 mg IV or esmolol 25-100
microgm/kg/min IV.
Monitor the ECG for 4-6 hours
B: Specific drugs and antidotes:
There is no specific antidote
C: Decontamination
Inhalation; remove victim from exposure, and give supplemental oxygen if available.
Ingestion; (a) Prehospital: Administer activated charcoal, if available. DO NOT induce vomiting because of rapid absorption and the risk of
abrupt onset CNS depression. (b) Hospital: Administer activated charcoal, although the efficacy of charcoal is unknown. Perform gastric
lavage only if the ingestion was very large and recent (less than 30 minutes)
D: Enhanced elimination:
There is no documented efficacy for diuresis, haemodialysis, haemoperfusion, or repeat-dose charcoal.
POISONING and DRUG OVERDOSE, Californian Poison Control System Ed. Kent R Olson; 3rd Edition
Do not administer sympathomimetic drugs unless absolutely necessary as material may increase myocardial irritability.
No specific antidote.
Because rapid absorption may occur through lungs if aspirated and cause systematic effects, the decision of whether to induce vomiting or
not should be made by an attending physician.
If lavage is performed, suggest endotracheal and/or esophageal control.
Danger from lung aspiration must be weighed against toxicity when considering emptying the stomach.
Treatment based on judgment of the physician in response to reactions of the patient
Acute exposures to carbon tetrachloride present, initially, with CNS depression followed by hepatic and renal dysfunction.
Respiratory depression and cardiac dysrhythmias are an immediate threat to life.
Since a major fraction of absorbed carbon tetrachloride is exhaled in the first hour, good tidal volumes should be maintained in severely
poisoned patients; hyperventilation may be an additional therapeutic modality.
Ipecac syrup, lavage, activated charcoal or catharsis may all be used in the first 4 hours.
Since reactive metabolites may cause hepatorenal toxicity, administration of N-acetyl-L-cysteine may reduce complications. Experience with
this therapy is limited. [Ellenhorn and Barceloux: Medical Toxicology]
DO NOT administer sympathomimetic drugs as they may cause ventricular arrhythmias.
SECTION 5 FIREFIGHTING MEASURES
Extinguishing media
Foam.
Dry chemical powder.
BCF (where regulations permit).
Carbon dioxide.
Special hazards arising from the substrate or mixture
Fire Incompatibility
Avoid contamination with oxidising agents i.e. nitrates, oxidising acids, chlorine bleaches, pool chlorine etc. as ignition may result
Advice for firefighters
Fire Fighting
Fire/Explosion Hazard
Alert Fire Brigade and tell them location and nature of hazard.
Wear full body protective clothing with breathing apparatus.
Prevent, by any means available, spillage from entering drains or water course.
Use water delivered as a fine spray to control fire and cool adjacent area.
WARNING:
Can become highly flammable in use.
Avoid evaporation.
SECTION 6 ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
Minor Spills
Remove all ignition sources.
Clean up all spills immediately.
Avoid breathing vapours and contact with skin and eyes.
Control personal contact with the substance, by using protective equipment.
Continued...
Chemwatch: 4838-93
Version No: 4.1.1.1
Major Spills
Page 5 of 9
Issue Date: 06/09/2013
A-Gas Solvokane
Print Date: 13/02/2014
Moderate hazard.
Clear area of personnel and move upwind.
Alert Fire Brigade and tell them location and nature of hazard.
Wear breathing apparatus plus protective gloves.
Personal Protective Equipment advice is contained in Section 8 of the MSDS.
SECTION 7 HANDLING AND STORAGE
Precautions for safe handling
Safe handling
Other information
DO NOT allow clothing wet with material to stay in contact with skin
Avoid all personal contact, including inhalation.
Wear protective clothing when risk of exposure occurs.
Store in original containers.
Keep containers securely sealed.
No smoking, naked lights or ignition sources.
Store in a cool, dry, well-ventilated area.
Conditions for safe storage, including any incompatibilities
Suitable container
Storage incompatibility
DO NOT use aluminium or galvanised containers
Metal can or drum
Packaging as recommended by manufacturer.
Avoid reaction with oxidising agents
Segregate from:
powdered metals such as aluminium, zinc and
alkali metals such as sodium, potassium and lithium.
PACKAGE MATERIAL INCOMPATIBILITIES
SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION
Control parameters
OCCUPATIONAL EXPOSURE LIMITS (OEL)
INGREDIENT DATA
Not Available
EMERGENCY LIMITS
Ingredient
TEEL-0
TEEL-1
TEEL-2
TEEL-3
trans-acetylene dichloride
200(ppm)
280(ppm)
1000(ppm)
1700(ppm)
Ingredient
Original IDLH
Revised IDLH
A-Gas Solvokane
Not Available
Not Available
Exposure controls
Appropriate engineering controls
Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designed engineering controls
can be highly effective in protecting workers and will typically be independent of worker interactions to provide this high level of protection.
The basic types of engineering controls are:
Process controls which involve changing the way a job activity or process is done to reduce the risk.
Personal protection
Eye and face protection
Skin protection
Safety glasses with side shields.
Chemical goggles.
Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policy document, describing
the wearing of lens or restrictions on use, should be created for each workplace or task.
See Hand protection below
Hand protection
Wear chemical protective gloves, e.g. PVC.
Wear safety footwear or safety gumboots, e.g. Rubber
The selection of suitable gloves does not only depend on the material, but also on further marks of quality which vary from manufacturer to
manufacturer. Where the chemical is a preparation of several substances, the resistance of the glove material can not be calculated in advance
and has therefore to be checked prior to the application.
Body protection
See Other protection below
Other protection
Overalls.
P.V.C. apron.
Barrier cream.
Thermal hazards
Recommended material(s)
Respiratory protection
Continued...
Chemwatch: 4838-93
Version No: 4.1.1.1
Page 6 of 9
Issue Date: 06/09/2013
A-Gas Solvokane
Print Date: 13/02/2014
Type AX Filter of sufficient capacity
GLOVE SELECTION INDEX
Glove selection is based on a modified presentation of the:
"Forsberg Clothing Performance Index".
The effect(s) of the following substance(s) are taken into account in the
A-Gas Solvokane Not Available
Material
CPI
* CPI - Chemwatch Performance Index
A: Best Selection
B: Satisfactory; may degrade after 4 hours continuous immersion
C: Poor to Dangerous Choice for other than short term immersion
Where the concentration of gas/particulates in the breathing zone,
approaches or exceeds the "Exposure Standard" (or ES), respiratory
protection is required.
Degree of protection varies with both face-piece and Class of filter;
the nature of protection varies with Type of filter.
Required
Minimum
Protection
Factor
Half-Face
Respirator
Full-Face
Respirator
Powered Air
Respirator
up to 10 x ES
AX-AUS
-
AX-PAPR-AUS /
Class 1
up to 50 x ES
-
AX-AUS / Class
1
up to 100 x ES -
AX-2
AX-PAPR-2 ^
^ - Full-face
A(All classes) = Organic vapours, B AUS or B1 = Acid gasses, B2 =
Acid gas or hydrogen cyanide(HCN), B3 = Acid gas or hydrogen
cyanide(HCN), E = Sulfur dioxide(SO2), G = Agricultural chemicals,
K = Ammonia(NH3), Hg = Mercury, NO = Oxides of nitrogen, MB =
Methyl bromide, AX = Low boiling point organic compounds(below
65 degC)
SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES
Information on basic physical and chemical properties
Appearance
Physical state
Colourless liquid with an ether-like odour; partly soluble in water.
Liquid
Relative density (Water = 1)
1.225
Odour
Not Available
Partition coefficient n-octanol / water
Not Available
Odour threshold
Not Available
Auto-ignition temperature (°C)
Not Available
pH (as supplied)
Not Applicable
Decomposition temperature
Not Available
Melting point / freezing point (°C)
Initial boiling point and boiling range
(°C)
Flash point (°C)
-43 (freezing point)
36
Viscosity (cSt)
Molecular weight (g/mol)
Not Applicable
0.53 mPa.s @ 25 deg.C
Not Applicable
Taste
Not Available
Not Available
Evaporation rate
Not Available
Explosive properties
Flammability
Not Available
Oxidising properties
Not Available
Upper Explosive Limit (%)
9.4
Surface Tension (dyn/cm or mN/m)
Not Available
Lower Explosive Limit (%)
5.4
Volatile Component (%vol)
Not Available
Vapour pressure (kPa)
5400 @ 20 deg.C
Solubility in water (g/L)
Partly Miscible
Vapour density (Air = 1)
>1
Gas group
pH as a solution(1%)
VOC g/L
Not Available
6 (1.7 g/l)
Not Available
SECTION 10 STABILITY AND REACTIVITY
Reactivity
Chemical stability
See section 7
Presence of incompatible materials.
Product is considered stable.
Hazardous polymerisation will not occur.
Possibility of hazardous reactions
See section 7
Conditions to avoid
See section 7
Incompatible materials
See section 7
Hazardous decomposition products
See section 5
SECTION 11 TOXICOLOGICAL INFORMATION
Information on toxicological effects
Inhaled
Inhalation of vapours or aerosols (mists, fumes), generated by the material during the course of normal handling, may be harmful.
Inhalation of vapours may cause drowsiness and dizziness. This may be accompanied by narcosis, reduced alertness, loss of reflexes, lack of
coordination and vertigo.
Limited evidence or practical experience suggests that the material may produce irritation of the respiratory system, in a significant number of
individuals, following inhalation.
Continued...
Chemwatch: 4838-93
Version No: 4.1.1.1
Ingestion
Skin Contact
Eye
Page 7 of 9
Issue Date: 06/09/2013
A-Gas Solvokane
Print Date: 13/02/2014
Accidental ingestion of the material may be harmful; animal experiments indicate that ingestion of less than 150 gram may be fatal or may produce
serious damage to the health of the individual.
Central nervous system (CNS) depression may include nonspecific discomfort, symptoms of giddiness, headache, dizziness, nausea,
anaesthetic effects, slowed reaction time, slurred speech and may progress to unconsciousness. Serious poisonings may result in respiratory
depression and may be fatal.
The material may produce moderate skin irritation; limited evidence or practical experience suggests, that the material either:
produces moderate inflammation of the skin in a substantial number of individuals following direct contact and/or
produces significant, but moderate, inflammation when applied to the healthy intact skin of animals (for up to four hours), such inflammation
being present twenty-four hours or more after the end of the exposure period.
Skin irritation may also be present after prolonged or repeated exposure; this may result in a form of contact dermatitis (nonallergic).
Limited evidence or practical experience suggests, that the material may cause moderate eye irritation in a substantial number of individuals
and/or may produce significant ocular lesions which are present twenty-four hours or more after instillation into the eye(s) of experimental
animals. Repeated or prolonged exposure may cause moderate inflammation (similar to windburn) characterised by a temporary redness of the
conjunctiva (conjunctivitis); temporary impairment of vision and/or other transient eye damage/ulceration may occur.
The vapour when concentrated has pronounced eye irritation effects and this gives some warning of high vapour concentrations. If eye irritation
occurs seek to reduce exposure with available control measures, or evacuate area.
Chronic
On the basis, primarily, of animal experiments, concern has been expressed by at least one classification body that the material may produce
carcinogenic or mutagenic effects; in respect of the available information, however, there presently exists inadequate data for making a
satisfactory assessment.
Limited evidence suggests that repeated or long-term occupational exposure may produce cumulative health effects involving organs or
biochemical systems.
It is generally accepted that the fluorocarbons are less toxic than the corresponding halogenated aliphatic based on chlorine. Repeated inhalation
exposure to the fluorocarbon FC-11 does not produce pathologic lesions of the liver and other visceral organs in experimental animals.
TOXICITY
IRRITATION
Not Available
Not Available
A-Gas Solvokane
365 mfc
TOXICITY
IRRITATION
Oral (rat) LD50: >2000 mg/kg *
Eye (rabbit): slight irritant *
Skin (rabbit): non-irritating *
Not Available
trans-acetylene dichloride
Not Available
TOXICITY
IRRITATION
Dermal (Rabbit) LD50: >5000 mg/kg
Eye (rabbit): 10 mg - moderate
Intraperitoneal (mouse) LD50: 3952 mg/kg
SKIN (RABBIT): 500 MG/24H - moderate
Intraperitoneal (rat) LD50: 7411 mg/kg
Oral (mouse) LD50: 2122 mg/kg
Oral (rat) LD50: 1235 mg/kg
Not Available
Not Available
* Value obtained from manufacturer's msds
unless otherwise specified data extracted from RTECS - Register of Toxic Effects of Chemical Substances
A-Gas Solvokane
365 MFC
TRANS-ACETYLENE DICHLORIDE
Acute Toxicity
The material may produce moderate eye irritation leading to inflammation. Repeated or prolonged exposure to irritants may produce
conjunctivitis.
The material may cause skin irritation after prolonged or repeated exposure and may produce a contact dermatitis (nonallergic). This form of
dermatitis is often characterised by skin redness (erythema) and swelling the epidermis.
Non-sensitising on guinea pig skin.* * Solvay MSDS
for dichloroethylene:
Acute toxicity: trans-1, 2-dichloroethylene showed low acute toxicity in several published data.
Repeat dose toxicity:
Hamster lung cell mutagen in vitro
Acute Toxicity (Oral) Category 4
Acute Toxicity (Inhalation) Category 4
Carcinogenicity
Not Applicable
Skin Irritation/Corrosion
Not Applicable
Reproductivity
Serious Eye Damage/Irritation
Not Applicable
STOT - Single Exposure
Not Applicable
Respiratory or Skin sensitisation
Not Applicable
STOT - Repeated Exposure
Not Applicable
Mutagenicity
Not Applicable
Aspiration Hazard
Not Applicable
STOT - SE (Narcosis) Category 3
CMR STATUS
SECTION 12 ECOLOGICAL INFORMATION
Continued...
Chemwatch: 4838-93
Version No: 4.1.1.1
Page 8 of 9
Issue Date: 06/09/2013
A-Gas Solvokane
Print Date: 13/02/2014
Toxicity
Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
Do NOT allow product to come in contact with surface waters or to intertidal areas below the mean high water mark. Do not contaminate water when cleaning equipment or disposing of equipment
wash-waters.
Wastes resulting from use of the product must be disposed of on site or at approved waste sites.
Persistence and degradability
Ingredient
Persistence: Water/Soil
Persistence: Air
Not Available
Not Available
Not Available
Bioaccumulative potential
Ingredient
Bioaccumulation
Not Available
Not Available
Mobility in soil
Ingredient
Mobility
Not Available
Not Available
SECTION 13 DISPOSAL CONSIDERATIONS
Waste treatment methods
Product / Packaging disposal
Containers may still present a chemical hazard/ danger when empty.
Return to supplier for reuse/ recycling if possible.
Otherwise:
If container can not be cleaned sufficiently well to ensure that residuals do not remain or if the container cannot be used to store the same
product, then puncture containers, to prevent re-use, and bury at an authorised landfill.
SECTION 14 TRANSPORT INFORMATION
Labels Required
Marine Pollutant
HAZCHEM
NO
Not Applicable
Land transport (ADG): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS
Air transport (ICAO-IATA / DGR): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS
Sea transport (IMDG-Code / GGVSee): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS
SECTION 15 REGULATORY INFORMATION
Safety, health and environmental regulations / legislation specific for the substance or mixture
365 mfc(406-58-6) is found on the
following regulatory lists
"International Maritime Dangerous Goods Requirements (IMDG Code)","IMO MARPOL 73/78 (Annex II) - List of Noxious Liquid Substances
Carried in Bulk","Australia - Victoria Occupational Health and Safety Regulations - Schedule 9: Materials at Major Hazard Facilities (And Their
Threshold Quantity) Table 2","International Maritime Dangerous Goods Requirements (IMDG Code) - Substance Index","United Nations
Recommendations on the Transport of Dangerous Goods Model Regulations (English)","Australia Dangerous Goods Code (ADG Code) - List
of Emergency Action Codes","Australia Customs (Prohibited Exports) Regulations 1958 - Schedule 15 Ozone depleting substances - Part 9
HFCs","United Nations Recommendations on the Transport of Dangerous Goods Model Regulations (Spanish)","Regulations concerning the
International Carriage of Dangerous Goods by Rail - Table A: Dangerous Goods List - RID 2013 (English)","International Air Transport
Association (IATA) Dangerous Goods Regulations","Australia Dangerous Goods Code (ADG Code) - Dangerous Goods List","Australia
Hazardous Substances Information System - Consolidated Lists","Australia - New South Wales Protection of the Environment Operations
(Waste) Regulation 2005 - Characteristics of trackable wastes"
trans-acetylene dichloride(156-60-5) is
found on the following regulatory lists
"International Maritime Dangerous Goods Requirements (IMDG Code)","Australia - Victoria Occupational Health and Safety Regulations Schedule 9: Materials at Major Hazard Facilities (And Their Threshold Quantity) Table 2","Australia Standard for the Uniform Scheduling of
Medicines and Poisons (SUSMP) - Appendix F (Part 3)","International Maritime Dangerous Goods Requirements (IMDG Code) - Substance
Index","Australia - Australian Capital Territory - Environment Protection Regulation: Ambient environmental standards (Domestic water supply inorganic chemicals)","Australia - Australian Capital Territory - Environment Protection Regulation: Ambient environmental standards (STOCK inorganic chemicals)","United Nations Recommendations on the Transport of Dangerous Goods Model Regulations
(English)","FisherTransport Information","Australia Dangerous Goods Code (ADG Code) - List of Emergency Action Codes","Australia Australian Capital Territory - Environment Protection Regulation: Pollutants entering waterways taken to cause environmental harm
(STOCK)","OSPAR National List of Candidates for Substitution – Norway","OECD List of High Production Volume (HPV)
Chemicals","Australia Drinking Water Guideline Values For Physical and Chemical Characteristics","WHO Guidelines for Drinking-water
Quality - Chemicals for which guideline values have not been established","United Nations Recommendations on the Transport of Dangerous
Goods Model Regulations (Spanish)","WHO Guidelines for Drinking-water Quality - Guideline values for chemicals that are of health
significance in drinking-water","Sigma-AldrichTransport Information","Australia National Pollutant Inventory","Australia - Australian Capital
Territory - Environment Protection Regulation: Pollutants entering waterways taken to cause environmental harm - Domestic water supply
quality","Regulations concerning the International Carriage of Dangerous Goods by Rail - Table A: Dangerous Goods List - RID 2013
(English)","International Air Transport Association (IATA) Dangerous Goods Regulations","Australia Dangerous Goods Code (ADG Code) Dangerous Goods List","Australia Hazardous Substances Information System - Consolidated Lists","Australia Standard for the Uniform
Scheduling of Medicines and Poisons (SUSMP) - Schedule 6","Australia - New South Wales Protection of the Environment Operations (Waste)
Regulation 2005 - Characteristics of trackable wastes","Australia - Australian Capital Territory - Environment Protection Regulation: Pollutants
entering waterways taken to cause environmental harm (IRRIG)","Australia - Australian Capital Territory - Environment Protection Regulation:
Ambient environmental standards (Domestic water supply - organic compounds)"
Continued...
Chemwatch: 4838-93
Version No: 4.1.1.1
Page 9 of 9
Issue Date: 06/09/2013
A-Gas Solvokane
Print Date: 13/02/2014
SECTION 16 OTHER INFORMATION
Other information
Classification of the preparation and its individual components has drawn on official and authoritative sources as well as independent review by the Chemwatch Classification committee using
available literature references.
A list of reference resources used to assist the committee may be found at:
www.chemwatch.net/references
The (M)SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whether the reported Hazards are Risks in the workplace or other
settings. Risks may be determined by reference to Exposures Scenarios. Scale of use, frequency of use and current or available engineering controls must be considered.
This document is copyright. Apart from any fair dealing for the purposes of private study, research, review or criticism, as permitted under the Copyright Act, no part may be reproduced by any
process without written permission from CHEMWATCH. TEL (+61 3) 9572 4700.
end of SDS
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement