Campbell Hausfeld | Brad Nailer CHN70200 | Operating instructions | Campbell Hausfeld Brad Nailer CHN70200 Operating instructions

Brad Nailer
Operating Instructions and Parts Manual
CHN70200
Française: Page 21
Español: página 41
MAKES IT EASY TO DO IT
IN727900AV 12/08
LIKE A PRO
chpower.com
Table of Contents
Description . . . . . . . . . . . . . . . . . . . . . . . . . 3
Air Hose Requirements . . . . . . . . . . . . 10
Specifications . . . . . . . . . . . . . . . . . . . . . . . 3
Loading / Unloading The Nailer . . . . . 11
Safety Guidelines . . . . . . . . . . . . . . . . . . . . 4
Loading the Nailer . . . . . . . . . . . . . . . 11
Safety Symbols . . . . . . . . . . . . . . . . . . . . . . 4
Unloading the Nailer . . . . . . . . . . . . . 11
Important Safety Information . . . . . . . . . 4
Adjusting The Nail Penetration . . . . . 11
Instructions Pertaining to a Risk
of Fire, Electric Shock, or Injury
to Persons . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installing No-Mar Tip . . . . . . . . . . . . . . 11
California Proposition 65 . . . . . . . . . . . . 4
General . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Removing No-Mar Tip . . . . . . . . . . . . . 11
Pre-Operation . . . . . . . . . . . . . . . . . . . . . . 12
Operational Modes . . . . . . . . . . . . . . . . 12
Sequential Mode . . . . . . . . . . . . . . . . 12
Work Area . . . . . . . . . . . . . . . . . . . . . . . . . 4
Bump Mode . . . . . . . . . . . . . . . . . . . . . 12
Personal Safety . . . . . . . . . . . . . . . . . . . . . 5
Electrical Safety . . . . . . . . . . . . . . . . . . . . 5
Tool Use and Care . . . . . . . . . . . . . . . . . . 5
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Air Source . . . . . . . . . . . . . . . . . . . . . . . . . 7
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Additional Items Not Included . . . . . . 7
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Getting To Know Your
Brad Nailer Like A Pro . . . . . . . . . . . . . . . . 9
Safety Lockout Mode . . . . . . . . . . . . . 12
Work Contact Element (WCE) . . . . . . 12
Electronics ON / OFF Switch . . . . . . . . 13
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Nail Placement Laser Pointer . . . . . . . 14
Firing the Nailer . . . . . . . . . . . . . . . . . . . 14
Low Nail Indicator Lights . . . . . . . . . . 14
Bubble Level . . . . . . . . . . . . . . . . . . . . . . 14
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Maintenance . . . . . . . . . . . . . . . . . . . . . . . 15
Clearing a Jam from the Nailer . . . . . . 15
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Nailer Repair . . . . . . . . . . . . . . . . . . . . . . 15
Anti-Dry Fire . . . . . . . . . . . . . . . . . . . . . . . 9
Replacement Parts . . . . . . . . . . . . . . . . 15
Tethered No-mar . . . . . . . . . . . . . . . . . . . 9
Battery Replacement . . . . . . . . . . . . . . 15
Low Nail Indicator Lights . . . . . . . . . . . 9
Assembly Procedure for Seals . . . . . . 15
Nail Placement Laser Pointer . . . . . . . . 9
Technical Service . . . . . . . . . . . . . . . . . . 16
Bubble Level . . . . . . . . . . . . . . . . . . . . . . . 9
Fastener Interchange Information . . 16
Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . 16
Lubrication . . . . . . . . . . . . . . . . . . . . . . . 10
Troubleshooting Guide . . . . . . . . . . . . . . 17
Minimum Components Required
for Hook-up . . . . . . . . . . . . . . . . . . . . . . 10
Replacement Parts List
for Brad Nailer . . . . . . . . . . . . . . . . . . 18 - 19
Hook-up Instructions For Nailer
to Air Supply . . . . . . . . . . . . . . . . . . . . . . 10
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
For parts, product and service information
Visit: www.chpower.com
Call :
Address any correspondence to:
Customer Service at 1-800-543-6400
Campbell Hausfeld
Attn: Customer Service
100 Production Drive
Harrison, OH 45030 U.S.A.
Operating Instructions and Parts Manual
Brad Nailer
Description
This nailer is designed for decorative trim, molding, window casings, furniture trim
and picture frame assembly. Features include: convenient side loading magazine which
holds up to 100 nails, tethered no-mar tip, quick clear nose, an adjustable depth of
drive mechanism, oil free, electronic low nail indicator, nail placement laser pointer,
in-line magazine, bubble level, anti-dry fire, conversion trigger with safety lockout,
rubber comfort grip, swivel plug, and rear exhaust.
Specifications
Model CHN70200
Requires: 0.3 Avg SCFM
using 10 fasteners per
minute at 90 psi
Air Inlet: 1/4 inch NPT
Fastener Size Range:
18g Brad Nails - 5/8 inch to
2 inch
Magazine Capacity: 100
fasteners per load
Weight: 3 lbs., 4 oz.
Length: 11 inches
Height: 10 inches
Maximum Pressure:
100 psi
Pressure Range: 60 psi to
100 psi
Batteries: Two (2) AAA
Laser: Class IIIA
Wavelength:
640 nm - 660 nm
Radiant Power:
1.53 < 5 mW
Figure 1 - CHN70200 Brad Nailer
Locate model number and date code on
magazine and / or tool body. Record below:
Model #: _____________________________
Date Code: ___________________________
Retain these numbers for future reference.
www.chpower.com
CHN70200
Operating Instructions and Parts Manual
Important Safety Information
Safety Guidelines
This manual contains
information that is very
important to know and
understand. This information
is provided for SAFETY and
to PREVENT EQUIPMENT
PROBLEMS. To help recognize
this information, observe the
following symbols.
Danger indicates an
imminently hazardous situation
which, if not avoided, WILL result
in death or serious injury.
Warning indicates a
potentially hazardous situation
which, if not avoided, COULD
result in death or serious injury.
Caution indicates a
potentially hazardous situation
which, if not avoided, MAY result in
minor or moderate injury.
Notice indicates important information, that if not
followed, may cause damage to
equipment.
IMPORTANT: Information that
requires special attention.
Safety Symbols
The following Safety Symbols
appear throughout this manual
to alert you to important safety
hazards and precautions.
Instructions Pertaining to a Risk of Fire, Electric Shock, or
Injury to Persons
This manual contains important safety, operational and maintenance information. If
you have any questions, please call 1-800-543-6400 for customer assistance.
When using tools, basic precautions should always be followed,
including the following:
California Proposition 65
This product or its power cord may contain chemicals known to the State
of California to cause cancer and birth defects or other reproductive
harm. Wash hands after handling.
You can create dust when you cut, sand, drill or grind
materials such as wood, paint, metal, concrete, cement, or
other masonry. This dust often contains chemicals known to cause cancer, birth
defects, or other reproductive harm. Wear protective gear.
General
a. To reduce the risks of electric shock, fire, and injury to persons, read
all the instructions before using the tool. Failure to follow warnings,
dangers, and cautions could result in DEATH or SERIOUS INJURY.
b. Be thoroughly familiar with the controls and the proper use of the
equipment. Follow all instructions. Contact your Campbell Hausfeld representative
if you have any questions.
c. Only persons well acquainted with these rules of safe operation should be allowed
to use the unit.
Do not operate or allow anyone else to operate the nailer if any warnings
or warning labels are not legible. Warnings or warning labels are located
on the nailer magazine and body.
Always assume the nailer contains nails. Respect the tool as a working
implement; no horseplay. Always keep others at a safe distance from
the work area in case of accidental discharge of nails. Do not point the tool toward yourself or
anyone whether it contains fasteners or not. Accidental triggering of the nailer could result in
death or serious personal injury.
Do not make any modifications to the tool without first obtaining
written approval from Campbell Hausfeld. Do not use the nailer if any
shields or guards are removed or altered. Do not use the nailer as a hammer. Personal injury or
tool damage may occur.
Clean and check all air supply hoses and fittings before connecting the
nailer to an air supply. Replace any damaged or worn hoses or fittings.
Tool performance or durability may be reduced.
Wear Eye
and Mask
Protection
Risk of Falling
Read Manual
First
Wear Eye
Protection
Risk of
Personal
Injury
Wear Hearing
Protection
Work Area
a. Keep the work area clean and well lighted. Cluttered benches and dark areas
increase the risks of electric shock, fire, and injury to persons.
b. Do not operate the tool in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. The tool is able to create
sparks resulting in the ignition of the dust or fumes.
c. Keep bystanders, children, and visitors away while operating the tool.
Distractions are able to result in the loss of control of the tool.
Risk of Fire
Risk of
Explosion
www.chpower.com
Risk of Shock
CHN70200
Operating Instructions and Parts Manual
Important Safety Information (Continued)
Personal Safety
a. Stay alert. Watch what you are doing and use common
sense when operating the tool. Do not use the tool
while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating the
tool increases the risk of injury to persons.
b. Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep hair, clothing, and gloves away
from moving parts. Loose clothes, jewelry, or long hair
increases the risk of injury to persons as a result of being
caught in moving parts.
c. Do not overreach. Keep proper footing and
balance at all times. Proper footing and balance
enables better control of the tool in unexpected
situations.
d. Use safety equipment. A dust mask, non-skid safety shoes
and a hard hat must be used for the applicable conditions.
Ensuring that the tool is used
only when the operator and all
other personnel in the work area are wearing ANSI Z87
eye protection equipment, and when required, other
appropriate protection equipment such as head, hearing
and foot protection equipment. Serious eye or permanent hearing
loss could result.
e. Always wear hearing protection when using the
tool. Prolonged exposure to high intensity noise
is able to cause hearing loss.
f. Do not attach the hose or tool to your body.
Attach the hose to the structure to reduce the risk of loss of
balance if the hose shifts.
g. Always assume that the tool contains fasteners.
Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
Do not drop or throw the tool. Dropping
or throwing the tool can result in damage that
will make the tool unusable or unsafe. If the tool has been dropped
or thrown, examine the tool closely for bent, cracked or broken parts
and air leaks. STOP and repair before using or serious injury could
occur.
Avoid long extended periods of work with the
nailer. Stop using the nailer if you feel pain in
hands or arms.
Hold tool by insulated gripping surface when performing an operation where the tool or
fastener may contact hidden wiring. Contacting a “live” wire will
make exposed metal parts of the tool “live” and shock the operator.
This is a Class IIIA Laser Product that laser
radiation
h. Never look directly into
the laser beam or its
direct reflection. Lasers
are harmful to the eyes.
i. Do not set up the tool
at eye level or operate
the tool on or near a
reflective surface. The
laser beam could be
projected into your own or
Figure 2
someone else’s eyes.
Never place hands or any other body parts in the nail discharge area
of the nailer. The nailer might eject a fastener and could
result in death or serious personal injury.
Electrical Safety
Replace batteries only with same size batteries. Do not mix old and
new batteries. Using wrong size batteries can create a risk
of fire or injury.
The front end of the tool may be made “live” if the tool comes
into contact with live wiring in the wall. TO PREVENT
ACCIDENTAL ELECTRICAL SHOCK, HOLD TOOL ONLY BY
THE SOFT GRIP HANDLE.
Tool Use and Care
a. Do not force the tool. Use the correct tool for the application.
The correct tool will do the job better and safer at the rate for
which the tool is designed.
Disconnect the tool from the air source before making adjustments, doing tool maintenance,
clearing jams, touching the safety yoke, leaving work area, loading,
or unloading the tool. Such precautionary measures reduce the risk of
injury to persons.
b. Store the tool when it is idle out of reach of children and
other untrained persons. A tool is dangerous in the hands of
untrained users.
c. Maintain the tool with care. A properly maintained tool
reduces the risk of problems and is easier to control.
d. Use only those fasteners listed in the “Fastener Interchange
Information” section on page 12 of this manual. Fasteners
not identified for use with this tool by the tool manufacturer
are able to result in a risk of injury to persons or tool damage
when used in this tool.
www.chpower.com
CHN70200
Operating Instructions and Parts Manual
Important Safety Information (Continued)
e. Always work in a well-ventilated area. Wear OSHAapproved dust mask.
Always disconnect the tool from the power source when unattended, performing any
maintenance or repair, clearing a jam, loading, unloading , or
moving the tool to a new location.
Always fit tool with a fitting or hose coupling on or near the tool in such a manner that all
compressed air in the tool is discharged at the time the fitting or
hose coupling is disconnected. Do not use a check valve or any other
fitting which allows air to remain in the nailer. Death or serious
personal injury could occur.
Never carry the nailer by the air hose or pull the hose to move the nailer or a compressor.
Keep hoses away from heat, oil and sharp edges. Replace any hose
that is damaged, weak or worn. Personal injury or tool damage
could occur.
Do not drive a nail on top of other nails. The nail could glance and cause death or a serious
puncture wound.
Do not use tool if laser guide power switch does not turn it on or off. Any tool that cannot be
controlled with the switch is dangerous and must be repaired.
f. Ensure the laser guide power switch is in the off position
before inserting batteries. Inserting the batteries into the
tool with the switch on invites accidents.
m. The product will emit a laser beam from the aperture.
The users of the product shall be limited to professional
operators. In normal operation and maintenance
conditions, the operators shall wear protective eyewear to
prevent injury to the eyes.
Do not expose tool to extreme heat.
n. Do not store in locations where the temperature may
reach or exceed 120°F (49°C), such as a metal tool shed, or
a car in the summer. This can lead to deterioration of the
battery.
o. Do not disassemble tool.
p. Remove batteries when storing tool for an extended time.
NOTE: Battery temperature will increase during and shortly
after use.
Only use new Alkaline replacement batteries [two (2) AAA
required]. Do not mix old and new batteries.
Battery shelf life - the included batteries may be in a slightly
depleted state or dead depending on how long the product has
awaited purchase. Do not return product to store for depleted
batteries; please call Campbell Hausfeld at 1-800-543-6400 for
assistance.
g. Turn laser guide Off before making any adjustments,
changing accessories, or storing. Such preventive safety
measures reduce the risk of accidents.
q. Do not modify or alter the nailer or any nailer parts. Do
not use the nailer if any shields or guards are removed or
altered. Do not use the nailer as a hammer. Personal injury
or tool damage may occur.
When batteries are not in use, keep them away from metal objects such as paper clips, coins,
keys, nails, or screws that can make a connection from one terminal
to another. Shorting the battery terminals together may cause sparks,
burns, a fire, or damage to the batteries.
Do not use any type of flammable gases or oxygen as a power source for the nailer.
Use filtered, lubricated, regulated compressed air only. Use of a
compressed gas instead of compressed air may cause the nailer to
explode which will cause death or serious personal injury.
h. This tool must NOT be modified or used for any
application other than that for which it was designed.
Never use gasoline or other flammable liquids to clean the nailer. Never use the nailer in
the presence of flammable liquids or gases. Vapors could ignite by a
spark and cause an explosion which will result in death or serious
personal injury.
i. Under abusive conditions, liquid may be ejected from the
batteries. Avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, seek medical help.
Liquid ejected from the batteries may cause irritation or
burns.
Use of controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
j. The use of optical instruments with this product will
increase eye hazard.
k. Turn off laser beam when it is not in use or when tool will
be left unattended.
l. Do not remove any labels from the tool.
www.chpower.com
r. Avoid using the nailer when the magazine is empty.
Accelerated wear on the nailer may occur.
Do not modify or disable the Work Contact Element (WCE). Do not tie or tape the WCE
or trigger in a depressed position. Death or serious personal injury
could result.
Always check that the Work Contact Element (WCE) is operating properly. A nail could
accidentally be driven if the WCE is not working properly. Personal
injury may occur.
Do not touch the trigger unless driving nails. Never attach air line to nailer or carry nailer
while touching the trigger. The tool could eject a fastener which will
result in death or serious personal injury.
CHN70200
Operating Instructions and Parts Manual
Important Safety Information (Continued)
Service
a. Tool service must be performed only by qualified repair
personnel.
b. When servicing a tool, use only identical replacement
parts. Use only authorized parts.
c. Use only the lubricants supplied with the tool or specified
by the manufacturer.
Disconnect air supply and release tension from the pusher before attempting to clear
jams because fasteners can be ejected from the front of the nailer.
Personal injury may occur.
Air Source
a. Never connect to an air source that is capable of exceeding
200 psi. Over pressurizing the tool is able to result in
bursting, abnormal operation, breakage of the tool or
serious injury to persons. Use only clean, dry, regulated
compressed air at the rated pressure or within the rated
pressure range as marked on the tool. Always verify prior to
using the tool that the air source has been adjusted to the
rated air pressure or within the rated air-pressure range.
b. Never use oxygen, carbon dioxide, combustible gases or
any bottled gas as an air source for the tool. Such gases are
capable of explosion and serious injury to persons.
Air compressors providing air to the nailer should follow the requirements established
by the American National Standards Institute Standard B19.3-1991;
Safety Standard for Compressors for Process Industries. Contact your
air compressor manufacturer for information.
Unpacking
After unpacking the unit, inspect carefully for any damage that
may have occurred during transit. Check for loose, missing
or damaged parts. Make sure to tighten fittings, bolts, etc.,
before putting unit into service. Check to be sure all supplied
accessories are enclosed with the unit. In case of questions,
damaged or missing parts, please call 1-800-543-6400 for
customer assistance.
Contents
u
u
u
u
u
Brad Nailer
2 inch, 18 gauge fasteners
Operating Instructions
Warranty Card
Carry Bag
Additional Items Not Included
u Compressor (must be able to maintain a minimum of 60 psi
when the nailer is being used)
u Air hose
u Small tool for clearing jams
u Threadlock glue
u ANSI Z87 eye protection
u Hearing protection and other personal protective
equipment as required
Assembly
This tool comes fully assembled.
Save These Instructions
Do Not Discard
The DANGER, WARNING, CAUTION, and NOTICE
notifications and instructions in this manual cannot
cover all possible conditions and situations that may
occur. It must be understood by the operator that
common sense and caution are factors which cannot
be built into this product, but must be supplied by the
operator.
www.chpower.com
CHN70200
Operating Instructions and Parts Manual
Glossary
Become familiar with these terms before operating the unit.
ActuatE (Tool) — To cause movement to the tool’s component(s) intended to
drive the fastener.
ACTUATION SYSTEM ­— The use of a trigger, work contact element (WCE) and/
or other operating control, separately or in combination or sequence, to actuate
the tool.
Air Inlet ­ — The opening in which the compressed air supply is connected,
usually by means of a threaded fitting.
Figure 3 - Quick Coupler
Fasteners ­ — This nailer uses 18g Brad Nails ranging in size from 5/8 inch to
2 inch.
Magazine — The part of the nailer that holds the Fasteners.
Maximum Air pressure — The maximum allowable pressure of compressed
air, as specified by the manufacture, for operating the tool.
No-mar tip — The no-mar tip is designed to eliminate marks caused by the
serrated Work Contact Element (WCE) (see Figure 5). The no-mar tip may be
removed and tethered to the tool if not required (See REMOVING NO-MAR TIP)
or when a slightly deeper countersink is preferred. Simply slide the no-mar off
the WCE and attach to the storage post on the tool’s electronic shroud.
Figure 4 - Quick Plug
psi (Pounds per Square Inch) —Measurement of the pressure exerted by
the force of the air. The actual psi output is measured by a pressure gauge on the
compressor.
Quick coupler ­— A quick coupler is designed to work in combination with a
quick plug to quickly and easily join a pneumatic tool to an air hose (see Figure 3).
Quick Plug — A quick plug is designed to work in combination with a quick
coupler to quickly and easily join a pneumatic tool to an air hose (see Figure 4).
Regulator ­— A device used to control air pressure to an air operated tool
Thread lock Glue — A locking glue that is applied to the screw threads
before installing. Prevents the screws from working loose during tool operation.
www.chpower.com
Figure 5
CHN70200
Operating Instructions and Parts Manual
Getting To Know Your Brad Nailer Like A Pro
Bubble
Level
Adjustable
Depth Control
Thumbwheel
Conversion Switch
Work Contact
Element (WCE)
Tethered
No-mar Tip
No-mar Tip
Storage Post
Low Nail
Indicator
Light
Trigger
Battery Cover/
Compartment
Rubber Comfort
Grip
Electronics
ON / OFF
Switch
Magazine
Rear Exhaust
Swivel Plug
Pull-out
Warning
Decal
Features
Anti-Dry Fire
This tool is equipped with an Anti-Dry
Fire feature. This prevents the Work
Contact Element (WCE) from being
pushed in when only a few nails remain.
Simply load new nail clip behind
remaining nails to continue shooting.
Tethered No-mar
The tool is fitted with a no-mar tip which
is tethered to the tool to prevent loss
when not mounted to tool. To utilize the
no-mar tip, simply slide it over the tools
WCE.
Low Nail Indicator Lights
The tool is equipped with lights on either
side of the tool near the nose. When the
nail count becomes low, the lights will
turn yellow. When the nail count is nearly
out, the Anti-Dry Fire feature will engage
and the lights will turn red. (See Loading
the Nailer section).
Nail Placement Laser Pointer
Quick Clear Nose
Cover
The tool is equipped with a laser mounted
near the nose. This can be seen through
the wide slots in the WCE and / or nomar tip. The laser will indicate exact
placement of the fastener.
Laser
This is a Class IIIA Laser Product that
emits laser radiation. Do not stare into beam
or view directly with optical instruments.
Bubble Level
The tool is equipped with a bubble level
located on the head cap. This will assist
in alighning the tool for level driving of
the fastener. The bubble level will assist
in vertical and horizontal positioning of
the tool.
Low Nail
Indicator
Light
Nail Loading Area
Magazine
Latch
Figure 6 - Components of the Brad Nailer
www.chpower.com
CHN70200
Operating Instructions and Parts Manual
Set-Up
Lubrication
60 psi Minimum
This nailer requires no lubrication for normal operation. However, lubrication will
not harm the tool.
100 psi Maximum
The work surface can become damaged by excessive lubrication.
Chart 1
Minimum Components Required For Hook-up
AIR COMPRESSOR: The air compressor must be able to maintain a minimum of 60 psi
when the nailer is being used. An inadequate air supply can cause a loss of power and
inconsistent driving (see Chart 1).
Rated 150 psi or greater
PRESSURE REGULATOR: A pressure regulator is required to control the operating
pressure of the nailer between 60 psi and 100 psi.
AIR SUPPLY HOSE: Always use air supply hoses with a minimum working pressure
rating equal to or greater than the pressure from the power source, or 150 psi,
whichever is greater. Use 1/4 inch air hose for runs up to 50 feet. Use 3/8 inch air hoses
for 50 ft. run or longer (see Figure 7 and Chart 2).
Interior Diameter
Figure 7 - Air Hose Requirements
Air Hose Requirements
Diameter
Length of Run
Hook-up Instructions For Nailer to Air Supply
1/4 inch
Less than 50 feet
Figure 8 shows the recommended hookup for the nailer.
3/8 inch
Greater than or equal
to 50 feet
NOTE: For better performance, install a 3/8 inch quick plug (1/4 inch NPT threads) with
an inside diameter of 0.315 inch (8 mm) on the nailer and a 3/8 inch quick coupler on
the air hose.
Chart 2
1. With ON/OFF switch in OFF position, plug compressor into electrical outlet.
2. Close pressure regulator by turning all the way to the left. Turn compressor ON and
let it pump all the way up to automatic shut-off pressure.
3. Attach air hose to regulator outlet. Adjust pressure regulator by turning to the right
so that outlet pressure is between 60 psi to 100 psi.
4. Load fasteners into nailer (See Loading/Unloading the Nailer section on page 11).
5. Point the nailer in a safe direction while attaching to air hose.
6. Nailer is ready for use. You may need to adjust outlet pressure to achieve proper
fastener depth.
Tank
Pressure
Gauge
Outlet
Pressure
Gauge
Regulator
Outlet
Quick
Coupler
Quick
Coupler
Regulator
Quick
Plug
Air
Hose
Figure 8 - Recommended Hookup
10
www.chpower.com
Swivel
Plug
CHN70200
Operating Instructions and Parts Manual
Set-Up (Continued)
Loading / Unloading The Nailer
Always disconnect the tool from the air supply before loading / unloading fasteners.
Choose which type of fastener you want to use for you project. Additional fasteners can
be found at major home centers.
Loading the Nailer
1. Press down on latch and pull back on the magazine cover.
2. Insert a stick of Campbell Hausfeld nails or equivalent (see “Fasteners” section) into
the magazine. Make sure the pointed ends of the nails are resting on the bottom
ledge of the magazine when loading. Make sure the nails are not dirty or damaged.
3. Push the magazine cover forward until the latch catches.
Unloading the Nailer
1. Press down on latch and pull back on the magazine cover.
2. Remove nails.
3. Push the magazine cover forward until the latch catches.
Adjusting The Nail Penetration
The CHN70200 is equipped with an adjustable depth of drive feature. This allows the
user to determine how deep a fastener will be driven into the work surface.
Figure 9 - Loading the Nailer
1. Adjust the operating pressure to a pressure which will consistently drive the
fasteners. Do not exceed the maximum operating pressure of 100 psi.
2. To drive the nail shallower, turn the wheel to left to the extent desired.
3. To sink a nail deeper, turn the wheel to right to the extent desired.
4. Make sure trigger and work contact element (WCE) move freely up and down
without binding or sticking after each adjustment.
Installing No-Mar Tip
1. Disconnect air supply from nailer.
2. Remove no-mar tip from the storage post.
Figure 10 - Nail Depth Adjust
3. Carefully place no-mar tip over the end of work contact element.
4. Check that the WCE and trigger move up and down freely without sticking or
binding.
No-mar Tip
Removing No-Mar Tip
1. Disconnect air supply from nailer.
Storage
Post
2. Pry no-mar tip away from the work contact element.
3. Replace no-mar tip onto the storage post for future use.
Figure 11 - No-mar Tip
www.chpower.com
11
CHN70200
Operating Instructions and Parts Manual
Pre-Operation
Depress WCE first...
Operational Modes
Always know the operational mode of the nailer before using. Failure to
know the operational mode could result in death or serious injury.
This nailer may be operated in the “Sequential” mode (as supplied by the
manufacturer) or “Bump” mode. the tool may be converted from one mode to the other
by firmly pressing the conversion switch from one position to the other.
Press the conversion switch to the “
” side to activate Sequential Mode.
Press the conversion switch to the “
” side to activate Bump Mode.
Press either side to the middle position to activate the Safety Lockout Mode.
Work Surface
Then pull trigger.
Sequential Mode
This method is recommended when precise nail placement is required. Operation in
this mode requires trigger to be pulled each time a nail is driven. Nailer can be actuated
by depressing the Work Contact Element (WCE) against work surface followed by
pulling the trigger.
The trigger must be released after each fastener is driven to allow tool to reset.
Since the tool can only be actuated by first removing the finger from the trigger, this
is considered to be a more restrictive mode of operation, suitable for less experienced
users.
Bump Mode
This method is recommended when less precise nail placement is required. Operation
in this mode requires trigger to be depressed with nailer off of the work surface. Then,
the nose of the nailer is tapped against the work surface causing a nail to be driven.
Work Surface
Figure 14 - Sequential Mode
Pull trigger first...
Each time the Work Contact Element is depressed, a nail is driven into the work
surface. Extreme care should be taken because a nail will be driven when the WCE is
pressed against any surface.
Since the tool can be actuated without removing the finger from the trigger, this is
considered to be a less restrictive mode, suitable for more experienced users.
Safety Lockout Mode
When the conversion switch is pressed into the middle position, the trigger is in Safety
Lockout Mode. In this mode, no combination of WCE and trigger activations will allow
the tool to cycle or fire. If tool does operate while in Safety Lockout Mode, contact
Campbell Hausfeld for technical support, and do not use the nailer until repaired.
Work Contact Element (WCE)
Check the operation of the Work Contact Element (WCE) trip mechanism before each use. The WCE must move freely without binding through its
entire travel distance. The WCE spring must return the WCE to its fully extended position after
being depressed. Do not operate the nailer if the WCE trip mechanism is not operating properly.
Personal injury may occur.
Work Surface
Then depress WCE.
1. Disconnect the air supply from the nailer.
2. Make sure the trigger and Work Contact Element (WCE) move freely up and down
without sticking or binding.
NOTE: If the tool is not loaded with nails, the anti-dry fire feature will not allow the
WCE to be depressed.
3. Reconnect air supply to the nailer.
4. Use a scrap piece of wood as a work surface.
12
www.chpower.com
Work Surface
Figure 15 - Bump Mode
CHN70200
Operating Instructions and Parts Manual
Pre-Operation (Continued)
5. Depress the WCE against the work surface without pulling the trigger (See
Figure 16). The nailer must not operate. Do not use the tool if it operates
without pulling the trigger. Personal injury may result.
6. Remove nailer from work surface. The WCE must return to its original down
position. Pull the trigger (See Figure 17). The nailer must not operate. Do not
use the tool if it operates while lifted from the work surface. Personal injury may
result.
7. Pull the trigger and depress the WCE against the work surface. The nailer MUST
operate when in bump mode. The nailer MUST NOT operate if in sequential
mode.
Work Surface
Figure 16
8. Depress the WCE against work surface. Pull the trigger. The nailer MUST operate.
9. Switch nailer into the other Mode as described in Operational Modes section and
repeat.
IMPORTANT: Repeat steps one through nine with tool in Safety Lockout Mode. Tool
should not operate at any step. If tool does operate while in Safety Lockout Mode,
contact Campbell Hausfeld for technical support.
Electronics ON / OFF Switch
Located on the battery compartment is an ON/ OFF for the tool’s electronic functions,
low nail indicator LEDs, and nail placement laser.
To utilize the function, turn the battery switch to the “ON” position. To avoid unwanted
battery depletion during storage, turn the switch to the “OFF” position.
Work Surface
Figure 17
Figure 18 - Electronic ON/OFF Switch
www.chpower.com
13
CHN70200
Operating Instructions and Parts Manual
Operation
Nail Placement Laser Pointer
The tool is equipped with a laser mounted near the nose. Turn the electronics switch
to the on position. When the Work Contact Element (WCE) touches the workpiece and
slightly moves, the laser will shine on the spot where the nail will be driven. This can
be seen through the wide slots in the WCE and / or no-mar tip. When the laser is in the
desired location, simply fully press in the WCE and fire the tool.
This is a Class IIIA Laser Product that emits laser radiation. Do not stare into beam or view directly with optical instruments.
NOTE: The laser will only show accurate placement when the depth control is set to
maximum depth.
Firing the Nailer
1. Load fasteners (see Loading / Unloading the Nailer section).
Figure 19 - Nail Placement Laser
Pointer
2. Connect the air supply to the nailer.
An improperly functioning tool must not be used. Do not actuate
the tool unless the tool is placed firmly against the work piece.
In Sequential Mode
Press the conversion switch to the “
” side to activate Sequential Mode.
1. Slightly depress Work Contact element (WCE) against work surface.
2. Laser pointer will shine on spot where nail will be driven when the WCE slightly
touches the work surface.
3. Fully depress WCE.
Figure 20 - Low Nail Indicator Lights
4. Pull trigger. Fastener will be driven into workpiece.
In Bump Mode (Laser should not be used in Bump Mode)
Press the conversion switch to the “
” side to activate Bump Mode.
1. Remove tool from work surface. DO NOT point tool at yourself or others.
2. Pull trigger.
3. Firmly depress Work Contact element (WCE) against work surface. Tool will cycle.
4. Remove tool from work surface. Move tool to the next area where fastener is to be
driven and repeat.
Low Nail Indicator Lights
The tool is equipped with lights on either side of the tool near the nose. Turn the
electronics switch to the on position. When the nail count becomes 10 or so nails
remaining in the magazine, the lights will come on yellow. You may reload at that time
(See Loading the Nailer section). When the nail count becomes 5 or so remaining nails,
the Anti-Dry Fire will engage and the lights will turn red. You must reload at that time.
Bubble Level
The tool is equipped with a bubble level located on the head cap. When the gun is in a
horizontal driving orientation, a level condition can easily be observed and controlled
by simply aligning the tool in such a manner whereas the bubble is between the center
markings on the length of the level. The same is true when in a vertically downward
driving orientation by aligning the tool such that the bubble is centered in the circular
marking at the top of the level.
14
www.chpower.com
Figure 21 - Bubble Level
CHN70200
Operating Instructions and Parts Manual
Storage
The nailer should be stored in a cool dry location.
Maintenance
Clearing A Jam From The Nailer
1. Disconnect nailer from air supply.
2. Remove all nails from the magazine (see Loading/ Unloading). Failure to do so
may cause the nails to eject from the front of the nailer.
3. Undo latch by pulling cover in the direction shown.
4. The door can now be rotated, exposing the jammed fastener.
5. Remove the jammed fastener, using pliers or a screwdriver if required.
6
Rotate door back into the closed position.
7. Extend the latch and place over the hooks on the nose.
Figure 22
8. Close the latch by pushing the latch up and in until the latch snaps into place.
9. Load with nails.
10. Make sure the trigger and work contact element (WCE) move freely up and down
without sticking or binding.
Nailer Repair
Only qualified personnel should repair the tool and they should use genuine Campbell
Hausfeld replacement parts and accessories, or parts and accessories which perform
equivalently.
Replacement Parts
Use only genuine Campbell Hausfeld service parts. Tool performance, safety and durability could be reduced if
improper parts are used. When ordering replacement parts, specify by part number.
Figure 23 - Battery Replacement
Battery Replacement
Always disconnect the tool from the power source when unattended, performing any maintenance or repair, clearing
a jam, loading, unloading , or moving the tool to a new location.
The electronics on the tool (low nail indicator lights and nail placement laser pointer)
run off of two (2) AAA batteries located in the compartment on the back of the
magazine. When the batteries’ power is running low and they need to be replaced,
the electronic functions may not work properly or at all. Disconnect the tool from air
source and remove the battery compartment cover by pulling out. Insert two (2) new
batteries in the proper orientation. Do not mix old and new batteries. Close cover.
Assembly Procedure For Seals
When repairing a nailer, the internal parts must be cleaned and lubricated. Parker Olube or equivalent must be used on all o-rings. Each o-ring must be coated with O-lube
before assembling. A small amount of oil must be used on all moving surfaces and
pivots.
www.chpower.com
15
CHN70200
Operating Instructions and Parts Manual
Maintenance (Continued)
Technical Service
For information regarding the operation or repair of this product, please call 1-800543-6400.
Fastener Interchange Information
Fasteners used in the Campbell Hausfeld CHN70200 Brad Nailer will also work in the
following brand units:
• Bostitch T31-1, T29-30, BT-35, BT50
• Duofast BB4440
• Hitachi NT45A
• Paslode 2138-F40
• Porter Cable BN125, BN200
• Sears 18409, 18424
• Senco SLP20, LS2, LS5.
Fasteners
The following Campbell Hausfeld brad nails are available at local retail stores. For help locating any item,
call customer service at 1-800-543-6400. Campbell Hausfeld nails meet or exceed ASTM Standard F1667.
Model #
Length
Shank Gauge
Finish
Head
Collation
Nails Per Stick
Nails Per Box
FB180016AV
5/8 inch
18 Gauge
Galvanized
Brad /Brown
Adhesive
100
1000
FB180025AV
1 inch
18 Gauge
Galvanized
Brad /Brown
Adhesive
100
1000
FB180030AV
1-1/4 inch
18 Gauge
Galvanized
Brad /Brown
Adhesive
100
1000
FB180040AV
1-1/2 inch
18 Gauge
Galvanized
Brad /Brown
Adhesive
100
1000
FB180050AV
2 inch
18 Gauge
Galvanized
Brad /Brown
Adhesive
100
1000
16
www.chpower.com
CHN70200
Operating Instructions and Parts Manual
Troubleshooting Guide
Stop using nailer immediately if any of the following problems occur. Serious personal injury could result. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center.
Symptom
cause
solution
Air leaking at trigger valve
O-rings in trigger valve housing are
damaged
Replace O-rings. Check operation of Work Contact
Element (WCE)
Air leaking between housing
and nose
1. Damaged O-rings and / or seals
1. Replace O-rings and / or seals
2. Damage to bumper
2. Replace bumper
Air leaking between housing
and cap
1. Loose screws
1. Tighten screws
2. Damaged gasket
2. Replace gasket
Nailer skips driving nail
1. Worn bumper
1. Replace bumper
2. Dirt in nose piece
2. Clean drive channel
3. Dirt or damage prevent nails or
pusher from moving freely in
magazine
3. Clean magazine
4. Damaged pusher spring
4. Replace spring
5. Inadequate air flow to nailer
5. Check fitting, hose, or compressor
6. Worn O-ring on piston or lack of
lubrication
6. Replace piston seals
7. Damaged O-ring on trigger valve
7. Replace O-rings
8. Air leaks
8. Tighten screws and fitings
Nailer runs slow or has loss of
power
1. Nailer not lubricated sufficiently
1. Lubricate nailer
2. Broken spring in cylinder cap
2. Replace spring
3. Exhaust port in cap is blocked
3. Replace damaged internal parts
Nails are jammed in nailer
1. Guide on driver is worn
1. Replace guide
2. Nails are not correct type
2. Use only recommended nails
3. Nails are bent
3. Replace with undamaged nails
4. Magazine or nose screws are loose
4. Tighten screws
5. Driver is damaged
5. Replace driver
6. Nails loaded incorrectly
6. Review Loading / Unloading section of manual
1. System power switch not turned on
1. Turn switch on
2. Batteries need to be replaced
2. Replace batteries (see “Changing batteries”
section)
3. Components not properly replaced
during re-assembly after customer
maintenance
3. Review parts view for assistance in proper reassembly
4. Laser won’t come on because WCE
not slightly depessed
4. Depress WCE to work surface
Laser and / or low nail
indicators not working
www.chpower.com
17
CHN70200
Operating Instructions and Parts Manual
For Replacement Parts or Technical Assistance, Call 1-800-543-6400
Please provide following information:
- Model number
- Serial number (if any)
- Part description and number as shown in parts list
Address any correspondence to:
Campbell Hausfeld
Attn: Customer Service
100 Production Drive
Harrison, OH 45030 U.S.A.
23
90
87
89
1
14
2
15
3
4
25
86
16
84
86
17
5
19
6
36
37
7
47
10
11
81
40
21
22
28 29
23
30
66
50
52
70
51
53
56
32
60
54 55
57
63
61
34
59
62
43
Figure 24 – Repair Parts Illustration for Air Powered Brad Nailer, model CHN70200AV
www.chpower.com
68
69
33
18
73 27
65
58
31
24
76
49
41
42
13
64
48
12
74
75
77
46
38
8
9
44
45
20
80
78 79
84
8
26
39
82
85
35
18
83
71
72
60
CHN70200
Operating Instructions and Parts Manual
Replacement Parts List for Brad Nailer
Ref.
No.Description
Part
No.
s
k
k
—
n l
n l
n
nl n l
n
—
n l
n l
n l
u
l u
l t
l t
t
t
l u
l u
—
u
—
l
π
H
—
—
H
‡
l —
—
l l k
k
‡
‡
—
—
‡ π
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
Bubble Level
Socket Head Cap Screw
Washer
Head Cap
Gasket
Seal
Upper Head Valve Bumper
O-Ring
O-Ring
Spring
Head Valve
O-Ring
Lower Head Valve Bumper
O-Ring
Collar
O-Ring
Spacer
O-Ring
Piston
Driver Blade
O-Ring
O-Ring
Cylinder
Bumper
Body
Nozzle
Socket Head Cap Screw
Screw
Upper Work Contact Element
Thumb Wheel
Pin
Spring
Lower Work Contact Element
No Mar Tip
Trigger Mode Selector Switch
Ball Bearing
Spring
Set Screw
Electronics Cover
Trigger Select Aperture
Roll Pin for Trigger Select Aperture
Roll Pin
Quick Clear Nose Cover
Seal
Upper Valve Body
Lower Valve Body
O-Ring
Trigger Valve Spring
Trigger Valve Stem
Trigger Spring
Retaining O-Ring
Trigger
Spring Pin
Socket Head Cap Screw
Socket Head Cap Screw
Quick Clear Nose Latch
Spring Steel
Plate
Quick Clear Nose Door
Spring Pin
Qty.
1
4
4
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
2
1
1
1
1
2
Ref.
No.Description
Part
No.
‡
k
—
k
—
—
k
—
k
ß
ß
ß
π
π
π
Ω
Ω
k
k
6
6
6
6
l †
†
k
—
l
—
SV567600AV
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
Roll Pin
Spring Pin
Drive Guide
Roll Pin
Magazine
Rail
Roll Pin
Magazine Door
Spring Pin
Bearing
Spring
Cantilever
Magazine End Cap
Spring
Thumb Latch
Screw
Recoil Decal Housing
Socket Head Cap Screw
Washer
Pusher
Magnet
Spring Seat
Spring
O-Ring
Rear Exhaust Air Tube
Spring Pin
Grip
Gasket
End Cap Magazine Bracket
1/4-18 NPT Swivel Plug
Qty.
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
2
2
1
2
1
1
1
1
REPLACEMENT PARTS KITS
s
n
l
u
t
H
‡
ß
π
Ω
6
†
—
k
Bubble Level Kit
SKN13600AV
Head Valve Repair Kit
SKN13700AV
Complete O-Ring Kit
SKN13800AV
Cylinder Repair Kit
SKN13900AV
Driver Assembly Kit
SKN14000AV
Electronics Module Kit
SKN14100AV
Lower WCE Kit
SKN14200AV
No-Mar Tip Kit
SKN14300AV
Conversion Trigger Switch Kit
SKN14400AV
Upper WCE Kit
SKN14500AV
Trigger Valve Repair Kit
SKN14600AV
Trigger Assembly Kit
SKN14700AV
Quick Clear Nose Repair Kit
SKN14800AV
ADF Repair Kit
SKN14900AV
Magazine Latch Assembly Kit
SKN15000AV
Warning Decal Kit
SKN15100AV
Pusher Assembly Kit
SKN15200AV
Rear Exhaust Repair Kit
SKN15300AV
Not Available
Standard hardware item - available at your local
hardware store
www.chpower.com
19
Operating Instructions and Parts Manual
CHN70200
Reminder: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
Warranty
1. DURATION: From the date of purchase by the original purchaser as follows: Standard Duty Products - One Year, Serious Duty
Products - Two Years, Extreme Duty Products - Three Years.
2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison,
Ohio, 45030, Telephone: (800) 543-6400
3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell
Hausfeld product.
4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld nailer, stapler, air tool, spray gun, inflator or air
accessory supplied or manufactured by Warrantor.
5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the
duration of the warranty period.
6. WHAT IS NOT COVERED UNDER THIS WARRANTY:
A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM
THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this product is used for commercial, industrial or
rental purposes, the warranty will apply for ninety (90) days from the date of purchase. Some States do not allow limitation
on how long an implied warranty lasts, so the above limitations may not apply to you.
B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY
DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with
instructions provided in the owner’s manual(s) supplied with product. Accident, purchaser’s abuse, neglect or failure to
operate products in accordance with instructions shall also include the removal or alteration of any safety devices. If such
safety devices are removed or altered, this warranty is void.
D. Normal adjustments which are explained in the owner’s manual(s) provided with the product.
E. Items or service that are normally required to maintain the product, i.e. o-rings, springs, bumpers, debris shields, driver
blades, fuses, batteries, gaskets, packings or seals, fluid nozzles, needles, sandblast nozzles, lubricants, material hoses, filter
elements, motor vanes, abrasives, blades, cut-off wheels, chisels, chisel retainers, cutters, collets, chucks, rivet jaws, screw
driver bits, sanding pads, back-up pads, impact mechanism, or any other expendable part not specifically listed. These
items will only be covered for ninety (90) days from date of original purchase. Underlined items are warranted for defects in
material and workmanship only.
7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or
components which are defective, have malfunctioned and/or failed to conform within duration of the warranty period.
8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:
A. Provide dated proof of purchase and maintenance records.
B. Deliver or ship the Campbell Hausfeld product or component to the nearest Campbell Hausfeld Authorized Service Center.
Freight costs, if any, must be borne by the purchaser.
C. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will
be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of
replacement parts.
This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights. You may also have
other rights which vary from state to state or country to country.
20
www.chpower.com
Download PDF

advertising