Sony DVP-NS32 User Guide Manual Operating Instruction Pdf

Sony DVP-NS32 User Guide Manual Operating Instruction Pdf
2-581-864-13(1)
CD/DVD
Player
Operating Instructions
DVP-NS52P
© 2005 Sony
Corporation
Downloaded From DvDPlayer-Manual.com Sherwood
Manuals
WARNING
To reduce the risk of fire or
electric shock, do not expose
this apparatus to rain or
moisture.
To avoid electrical shock, do
not open the cabinet. Refer
servicing to qualified
personnel only.
The mains lead must only be
changed at a qualified
service shop.
This appliance is classified as a
CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT
MARKING is located on the rear
exterior.
CAUTION
The use of optical instruments with
this product will increase eye
hazard. As the laser beam used in
this CD/DVD player is harmful to
eyes, do not attempt to disassemble
the cabinet.
Refer servicing to qualified
personnel only.
Notice for customers in the
United Kingdom and
Republic of Ireland
A moulded plug complying with
BS1363 is fitted to this equipment
for your safety and convenience.
Should the fuse in the plug
supplied need to be replaced, a
5AMP fuse approved by ASTA or
BSI to BS1362, (i.e., marked with
or
mark) must be used.
If the plug supplied with this
equipment has a detachable fuse
cover, be sure to attach the fuse
cover after you change the fuse.
Never use the plug without the fuse
cover. If you should lose the fuse
cover, please contact your nearest
Sony service station.
Notes About the
Discs
• To keep the disc clean, handle
the disc by its edge. Do not touch
the surface.
Disposal of Old Electrical &
Electronic Equipment (Applicable
in the European Union and other
European countries with separate
collection systems)
This symbol on the product or on
its packaging indicates that this
product shall not be treated as
household waste. Instead it shall be
handed over to the applicable
collection point for the recycling of
electrical and electronic
equipment. By ensuring this
product is disposed of correctly,
you will help prevent potential
negative consequences for the
environment and human health,
which could otherwise be caused
by inappropriate waste handling of
this product. The recycling of
materials will help to conserve
natural resources. For more
detailed information about
recycling of this product, please
contact your local Civic Office,
your household waste disposal
service or the shop where you
purchased the product.
Precautions
Safety
• This unit operates on 220 – 240
V AC, 50/60 Hz. Check that the
unit’s operating voltage is
identical with your local power
supply.
• To prevent fire or shock hazard,
do not place objects filled with
liquids, such as vases, on the
apparatus.
Installing
• Do not install the unit in an
inclined position. It is designed
to be operated in a horizontal
position only.
• Keep the unit and discs away
from equipment with strong
magnet, such as microwave
ovens, or large loudspeakers.
• Do not place heavy objects on
the unit.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
2
• Do not expose the disc to direct
sunlight or heat sources such as
hot air ducts, or leave it in a car
parked in direct sunlight as the
temperature may rise
considerably inside the car.
• After playing, store the disc in its
case.
• Clean the disc with a cleaning
cloth.
Wipe the disc from the centre
out.
• Do not use solvents such as
benzine, thinner, commercially
available disc/lens cleaners, or
anti-static spray intended for
vinyl LPs.
• If you have printed the disc's
label, dry the label before
playing.
On adjusting volume
Precautions
On safety
Should any solid object or liquid fall into the
cabinet, unplug the player and have it
checked by qualified personnel before
operating it any further.
On power sources
• The player is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the
player itself has been turned off.
• If you are not going to use the player for a
long time, be sure to disconnect the player
from the wall outlet. To disconnect the AC
power cord (mains lead), grasp the plug
itself; never pull the cord.
On placement
• Place the player in a location with adequate
ventilation to prevent heat build-up in the
player.
• Do not place the player on a soft surface
such as a rug.
• Do not place the player in a location near
heat sources, or in a place subject to direct
sunlight, excessive dust, or mechanical
shock.
On operation
• If the player is brought directly from a cold
to a warm location, or is placed in a very
damp room, moisture may condense on the
lenses inside the player. Should this occur,
the player may not operate properly. In this
case, remove the disc and leave the player
turned on for about half an hour until the
moisture evaporates.
• When you move the player, take out any
discs. If you don’t, the disc may be
damaged.
Do not turn up the volume while listening to
a section with very low level inputs or no
audio signals. If you do, the speakers may be
damaged when a peak level section is played.
On cleaning
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent
such as alcohol or benzine.
On cleaning discs, disc/lens cleaners
Do not use a commercially available
cleaning disc or disc/lens cleaner (wet or
spray type). These may cause the
apparatus to malfunction.
IMPORTANT NOTICE
Caution: This player is capable of holding a
still video image or on-screen display image
on your television screen indefinitely. If
you leave the still video image or on-screen
display image displayed on your TV for an
extended period of time you risk permanent
damage to your television screen. Plasma
display panel televisions and projection
televisions are susceptible to this.
If you have any questions or problems
concerning your player, please consult your
nearest Sony dealer.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
3
Table of Contents
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Notes About the Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
This Player Can Play the Following Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Index to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Guide to the Control Menu Display (Magic Pad) . . . . . . . . . . . . . . . . . . . . . . 11
Hookups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Hooking Up the Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 1: Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 2: Inserting Batteries Into the Remote . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 3: Connecting the Video Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 4: Connecting the Audio Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 5: Connecting the Mains Lead. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 6: Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
14
14
15
19
21
21
Playing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Playing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Resuming Playback From the Point Where You Stopped the Disc (Multi-disc
Resume) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Using the DVD’s Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Selecting “ORIGINAL” or “PLAY LIST” on a DVD-RW . . . . . . . . . . . . . . . . . 27
Playing VIDEO CDs With PBC Functions (PBC Playback) . . . . . . . . . . . . . . 28
Various Play Mode Functions (Programme Play, Shuffle Play, Repeat Play,
A-B Repeat Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Searching for a Scene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Searching for a Particular Point on a Disc (Search, Scan, Slow-motion Play,
Freeze Frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Searching for a Title/Chapter/Track/Scene, etc. . . . . . . . . . . . . . . . . . . . . . . 34
Searching by Scene (PICTURE NAVIGATION) . . . . . . . . . . . . . . . . . . . . . . 36
Viewing Information About the Disc . . . . . . . . . . . . . . . . . . . . . . . 37
Checking the Playing Time and Remaining Time . . . . . . . . . . . . . . . . . . . . . 37
Sound Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Changing the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
TV Virtual Surround Settings (TVS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Enjoying Movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Changing the Angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying the Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Playback Picture (CUSTOM PICTURE MODE). . . . . . . . . . . .
Sharpening the Pictures (SHARPNESS) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
4
45
45
46
48
Enjoying MP3 Audio and JPEG Images . . . . . . . . . . . . . . . . . . . . . 49
About MP3 Audio Tracks and JPEG Image Files . . . . . . . . . . . . . . . . . . . . . 49
Playing MP3 Audio Tracks or JPEG Image Files. . . . . . . . . . . . . . . . . . . . . . 50
Enjoying JPEG Images as a Slide Show . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Enjoying DivX® Videos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
About DivX Video Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Playing DivX Video Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Using Various Additional Functions . . . . . . . . . . . . . . . . . . . . . . . 59
Locking Discs (CUSTOM PARENTAL CONTROL,
PARENTAL CONTROL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Controlling Your TV With the Supplied Remote. . . . . . . . . . . . . . . . . . . . . . . 62
Settings and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Using the Setup Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Display or Sound Track Language (LANGUAGE SETUP) . . . . .
Settings for the Display (SCREEN SETUP). . . . . . . . . . . . . . . . . . . . . . . . . .
Custom Settings (CUSTOM SETUP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings for the Sound (AUDIO SETUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
63
64
65
66
67
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Self-diagnosis Function (When letters/numbers appear in the display). . . . .
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Language Code List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
73
73
75
76
77
About This Manual
•Instructions in this manual describe the controls on the remote. You can also use the controls
on the player if they have the same or similar names as those on the remote.
•“DVD” may be used as a general term for DVD VIDEOs, DVD+RWs/DVD+Rs and DVDRWs/DVD-Rs.
•The meaning of the icons used in this manual is described below:
Icons
Meanings
Functions available for DVD VIDEOs and DVD+RWs/DVD+Rs in +VR mode
or DVD-RWs/DVD-Rs in video mode
Functions available for DVD-RWs in VR (Video Recording) mode
Functions available for VIDEO CDs (including Super VCDs or CD-Rs/CD-RWs
in video CD format or Super VCD format)
Functions available for music CDs or CD-Rs/CD-RWs in music CD format
Functions available for DATA CDs (CD-ROMs/CD-Rs/CD-RWs containing
MP3*1 audio tracks, JPEG image files, and DivX*2*3 video files)
Functions available for DATA DVDs (DVD-ROMs/DVD+RWs/DVD+Rs/DVD-RWs/
DVD-Rs) containing MP3*1 audio tracks, JPEG image files and DivX*2*3 video files.
*1 MP3 (MPEG-1 Audio Layer III) is a standard format defined by ISO (International Organization for
Standardization)/IEC (International Electrotechnical Commission) MPEG which compresses audio data.
*2 DivX® is a video file compression technology, developed by DivXNetworks, Inc.
*3 DivX, DivX Certified, and associated logos are trademarks of DivXNetworks, Inc. and are used under license.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
5
This Player Can Play the
Following Discs
Format of discs
DVD VIDEO
DVD-RW/-R
DVD+RW/+R
VIDEO CD/
Music CD
CD-RW/-R
Example of discs that the player
cannot play
The player cannot play the following discs:
• CD-ROMs/CD-Rs/CD-RWs other than
those recorded in the formats listed on this
page.
• CD-ROMs recorded in PHOTO CD format.
• Data part of CD-Extras.
• DVD Audio discs.
• DATA DVDs that do not contain MP3
audio tracks, JPEG image files, or DivX
video files.
• HD layer on Super Audio CDs.
Also, the player cannot play the following
discs:
• A DVD VIDEO with a different region
code.
• A disc that has a non-standard shape (e.g.,
card, heart).
• A disc with paper or stickers on it.
• A disc that has the adhesive of cellophane
tape or a sticker still left on it.
Region code
“DVD+RW,” “DVD-RW,” “DVD+R,”
“DVD-Video” and the “CD” logo are
trademarks.
Note about CDs/DVDs
The player can play CD-ROMs/CD-Rs/CDRWs recorded in the following formats:
– music CD format
– video CD format
– MP3 audio tracks, JPEG image files, and
DivX video files of format conforming to
ISO 9660* Level 1/Level 2, or its extended
format, Joliet
– KODAK Picture CD format
* A logical format of files and folders on CDROMs, defined by ISO (International
Organization for Standardization).
Your player has a region code printed on the
back of the unit and only will play DVD
VIDEOs (playback only) labelled with
identical region codes. This system is used to
protect copyrights.
DVD VIDEOs labelled
this player.
will also play on
If you try to play any other DVD VIDEO, the
message “Playback prohibited by area
limitations.” will appear on the TV screen.
Depending on the DVD VIDEO, there may
be no region code indication, even though
playing the DVD VIDEO is prohibited by
area restrictions.
DVP–XXXX
X
00V 00Hz
NO.
00W
The player can play DVD-ROMs/
DVD+RWs/DVD-RWs/DVD+Rs/DVD-Rs
recorded in the following formats:
– MP3 audio tracks, JPEG image files and
DivX video files of format conforming to
UDF (Universal Disk Format).
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
6
ALL
0-000-000-00
Region code
Notes
• Notes about DVD+RWs/DVD+Rs, DVD-RWs/
DVD-Rs or CD-Rs/CD-RWs
Some DVD+RWs/DVD+Rs, DVD-RWs/DVDRs, or CD-Rs/CD-RWs cannot be played on this
player due to the recording quality or physical
condition of the disc, or the characteristics of the
recording device and authoring software.
The disc will not play if it has not been correctly
finalized. For more information, refer to the
operating instructions for the recording device.
Note that some playback functions may not work
with some DVD+RWs/DVD+Rs, even if they
have been correctly finalized. In this case, view
the disc by normal playback. Also some DATA
CDs/DATA DVDs created in Packet Write
format cannot be played.
• Music discs encoded with copyright protection
technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
• Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
Copyrights
This product incorporates copyright
protection technology that is protected by
U.S. patents and other intellectual property
rights. Use of this copyright protection
technology must be authorized by
Macrovision, and is intended for home and
other limited viewing uses only unless
otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.
Note on playback operations of
DVDs and VIDEO CDs
Some playback operations of DVDs and
VIDEO CDs may be intentionally set by
software producers. Since this player plays
DVDs and VIDEO CDs according to the disc
contents the software producers designed,
some playback features may not be available.
Also, refer to the instructions supplied with
the DVDs or VIDEO CDs.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
7
Index to Parts and Controls
For more information, see the pages indicated in parentheses.
Front panel
A [/1 (on/standby) button (24)
F H (play) button (24)
B Disc tray (24)
G X (pause) button (25)
C Front panel display (9)
H x (stop) button (25)
D
I ./> (previous/next) buttons (33)
(remote sensor) (14)
E A (open/close) button (24)
J PROGRESSIVE button/indicator (17)
Lights up when the player outputs
progressive signals.
Rear panel
LINE OUT
VIDEO
COAXIAL
R
OPTICAL
DIGITAL OUT
Y
PB/CB
AUDIO
L
LINE
(RGB)
-TV
L
CENTER
PR/CR
COMPONENT VIDEO OUT
S VIDEO OUT
A DIGITAL OUT (COAXIAL) jack (19)
D LINE (RGB) - TV jack (15)
B LINE OUT L/R (AUDIO) jacks (19)
E S VIDEO OUT jack (15)
C LINE OUT (VIDEO) jack (15)
F COMPONENT VIDEO OUT (Y, PB/
CB, PR/CR) jacks (15)
G DIGITAL OUT (OPTICAL) jack (19)
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
8
Front panel display
When playing back a DVD VIDEO/DVD-RW
Disc type
Playing status Lights up when you can change the angle (45)
Lights up during
Repeat Play (31)
Current audio signal (42)
Current title/chapter or playing
time (37)
When playing back a VIDEO CD with Playback Control (PBC) (28)
Disc type
Playing status
Lights up during A-B Repeat Play (32)
Current scene or playing time (37)
When playing back a CD, DATA DVD (MP3 audio/DivX video), DATA CD (MP3 audio/DivX
video), or VIDEO CD (without PBC)
Playing status
Disc type*2
Lights up during
Repeat Play (31)
Current track*1 (37)
Lights up when playing MP3 audio tracks (49)
Playing time (37)
*1 When playing DivX video files, the current track is not displayed.
*2 When playing DATA DVDs, the DVD indicator is displayed.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
9
Remote
J
m/M
(34)
(scan/slow) buttons
K ZOOM button (25, 52)
L SLOW PLAY/FAST PLAY buttons
(25)
M
(audio) button (41)
N
(subtitle) button (45)
O [/1 (on/standby) button (24)
P 2 (volume) +/– buttons (62)
The + button has a tactile dot.*
Q t (TV/video) button (62)
R PICTURE NAVI (picture navigation)
button (36, 52)
S TIME/TEXT button (37)
T MENU button (27)
U ENTER button (21)
V DISPLAY button (11)
W H (play) button (24)
The H button has a tactile dot.*
X x (stop) button (25)
Y X (pause) button (25)
Z SUR (surround) button (43)
wj
(angle) button (45)
* Use the tactile dot as a reference when operating
the player.
A TV [/1 (on/standby) button (62)
B Z (open/close) button (25)
C Number buttons (27)
The number 5 button has a tactile dot.*
D CLEAR button (29)
E TOP MENU button (27)
F C/X/x/c buttons (27)
G O RETURN (return) button (25)
H
/
(replay/step/
advance/step) buttons (25, 34)
I ./> (previous/next) buttons (25)
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
10
Guide to the Control Menu Display (Magic Pad)
Use the Control Menu to select a function and to view related information. Press DISPLAY
repeatedly to turn on or change the Control Menu display as follows:
, Control Menu display 1
m
Control Menu display 2 (Only for DATA CDs/DATA DVDs without DivX video files)
m
Control Menu display off
Control Menu display
The Control Menu display 1 and 2 will show different items depending on the disc type. For
details about each item, see the pages in parentheses.
Example: Control Menu display 1 when playing a DVD VIDEO.
Currently playing chapter number*2
Currently playing title number*1
Total number of titles*1
Total number of chapters*2
Control Menu items
Selected item
Function name of
selected Control
Menu item
Operation message
12(27)
18(34)
T
1:32:55
OFF
OFF
SET
ON
PLAY
DVD VIDEO
Playback status
(N Playback,
X Pause,
x Stop, etc.)
Type of disc
being played*3
Playing time*4
Current setting
Options
PROGRAM
ENTER
Quit: DISPLAY
*1 Displays the scene number for VIDEO CDs
(PBC is on), track number for VIDEO CDs/CDs,
album number for DATA DVDs/DATA CDs.
*2 Displays the index number for VIDEO CDs,
MP3 audio track number or JPEG image file
number for DATA CDs/DATA DVDs. DivX
video file number for DATA CDs/DATA
DVDs.
*3 Displays Super VCD as “SVCD.”
*4 Displays the date for JPEG files.
To turn off the display
Press DISPLAY.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
11
List of Control Menu items
Item
Item Name, Function
TITLE (page 34)/SCENE (page 35)/TRACK (page 34)
Selects the title, scene, or track to be played.
CHAPTER (page 34)/INDEX (page 34)
Selects the chapter or index to be played.
TRACK (page 35)
Selects the track to be played.
ORIGINAL/PLAY LIST (page 27)
Selects the type of titles (DVD-RW) to be played, the ORIGINAL one, or an edited
PLAY LIST.
TIME/TEXT (page 34)
Checks the elapsed time and the remaining playback time.
Input the time code for picture and music searching.
Displays the DVD/CD text, or the DATA CD/DATA DVD track/file name.
PROGRAM (page 29)
Selects the title, chapter, or track to play in the order you want.
SHUFFLE (page 30)
Plays the title, chapter, or track in random order.
REPEAT (page 31)
Plays the entire disc (all titles/all tracks/all albums) repeatedly or one title/chapter/
track/album/file repeatedly.
A-B REPEAT (page 32)
Specifies the parts you want to play repeatedly.
CUSTOM PICTURE MODE (page 46)
Adjusts the video signal from the player. You can select the picture quality that best
suits the program you are watching.
SHARPNESS (page 48)
Exaggerates the outline of the image to produce a sharper picture.
PARENTAL CONTROL (page 59)
Set to prohibit playback on this player.
SETUP (page 63)
QUICK Setup (page 21)
Use Quick Setup to choose the desired language of the on-screen display, the aspect
ratio of the TV, and the audio output signal.
CUSTOM Setup
In addition to the Quick Setup setting, you can adjust various other settings.
RESET
Returns the settings in “SETUP” to the default setting.
ALBUM (page 35)
Selects the album that contain JPEG image file to be played.
FILE (page 35)
Selects the JPEG image file to be played.
ALBUM (page 35)
Selects the album that contain DivX video file to be played.
FILE (page 35)
Selects the DivX video file to be played.
DATE (page 52)
Displays the date the picture was taken by a digital camera.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
12
INTERVAL (page 54)
Specifies the duration for which the slides are displayed on the screen.
EFFECT (page 55)
Selects the effects to be used for changing slides during a slide show.
MODE (MP3, JPEG) (page 53)
Selects the data type; MP3 audio track (AUDIO), JPEG image file (IMAGE) or both
(AUTO) to be played when playing a DATA CD/DATA DVD.
z Hint
The Control Menu icon indicator lights up in green
when you select any item
t
except “OFF.” (“PROGRAM,” “SHUFFLE,”
“REPEAT,” “A-B REPEAT,” “SHARPNESS,”
“CUSTOM PICTURE MODE” only). The
“ORIGINAL/PLAY LIST” indicator lights up in
green when you select “PLAY LIST” (default
setting).
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
13
Hookups
Hooking Up the Player
Follow steps 1 to 6 to hook up and adjust the settings of the player.
Notes
•
•
•
•
Plug cords securely to prevent unwanted noise.
Refer to the instructions supplied with the components to be connected.
You cannot connect this player to a TV that does not have a SCART or video input jack.
Be sure to disconnect the mains lead of each component before connecting.
Step 1: Unpacking
Check that you have the following items:
• Audio/video cord (phono plug × 3 y phono plug × 3) (1)
• Remote commander (remote) (1)
• R6 (size AA) batteries (2)
Step 2: Inserting Batteries Into the Remote
You can control the player using the supplied remote. Insert two R6 (size AA) batteries by
matching the 3 and # ends on the batteries to the markings inside the compartment. When
using the remote, point it at the remote sensor
on the player.
Notes
• Do not leave the remote in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or a lighting apparatus. Doing so may cause a
malfunction.
• If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
14
Step 3: Connecting the Video Cords
C
S VIDEO cord
(not supplied)
(yellow)
INPUT
Hookups
Connect this player to your TV monitor, projector, or AV amplifier (receiver) using a video cord.
Select one of the patterns A through D, according to the input jack on your TV monitor,
projector, or AV amplifier (receiver).
In order to view progressive signal (525p or 625p) pictures with a compatible TV, projector, or
monitor, you must use pattern A.
D
INPUT
S VIDEO
Audio/video
cord (supplied)
VIDEO
TV, projector, or AV
amplifier (receiver)
L
AUDIO
R
TV, projector, or AV
amplifier (receiver)
(yellow)
to S VIDEO OUT
to LINE OUT (VIDEO)
LINE OUT
VIDEO
COAXIAL
R
OPTICAL
DIGITAL OUT
Y
PB/CB
AUDIO
L
COMPONENT VIDEO OUT
L
CENTER
S VIDEO OUT
to COMPONENT
VIDEO OUT
(green)
LINE
(RGB)
-TV
PR/CR
CD/DVD player
to LINE
(RGB)-TV
(blue)
SCART cord
(not supplied)
(red)
COMPONENT
VIDEO IN
Y
(green)
PB/CB
(blue)
(red)
PR/CR
TV, projector, or AV
amplifier (receiver)
A
Component video
cord (not supplied)
TV
B
l : Signal flow
Note
When connecting to a progressive TV, it is recommended that you use only pattern A. If you connect to your
TV using both A and B, a special control signal transmitted via the SCART cable may cause the signal to
be switched to the SCART jack.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
15
A If you are connecting to a monitor, projector, or AV amplifier
(receiver) having component video input jacks (Y, PB/CB, PR/CR)
Connect the component via the COMPONENT VIDEO OUT jacks using a component video
cord (not supplied) or three video cords (not supplied) of the same kind and length. You will
enjoy accurate colour reproduction and high quality images.
If your TV accepts progressive 525p/625p format signals, use this connection and press the
PROGRESSIVE button on the front panel to output progressive signals. For details, see “Using
the PROGRESSIVE button” (page 17).
Green
Blue
Blue
Green
Red
Red
B If you are connecting to a SCART input jack
Connect a SCART cord (not supplied). Be sure to make the connections firmly to avoid hum and
noise. When you connect using the SCART cord, check that the TV conforms to S video or RGB
signals. Refer to the operating instructions supplied with the TV to be connected. Also, when
you set “LINE” to “S VIDEO” or “RGB” under “SCREEN SETUP” in the Setup Display
(page 65), use a SCART cord that conforms to each signal.
With this connection, select “NORMAL (INTERLACE)” (default) by pressing the
PROGRESSIVE button on the front panel.
When connecting to a wide screen TV
Depending on the disc, the image may not fit your TV screen. To change the aspect ratio, see
page 65.
C If you are connecting to a video input jack
Connect the yellow plug of an audio/video cord (supplied) to the yellow (video) jack. You will
enjoy standard quality images.
With this connection, select “NORMAL (INTERLACE)” (default) by pressing the
PROGRESSIVE button on the front panel.
Yellow
White (L)
Yellow
Red (R)
Red (R)
White (L)
D If you are connecting to an S VIDEO input jack
Connect an S VIDEO cord (not supplied). You will enjoy high quality images.
With this connection, select “NORMAL (INTERLACE)” (default) by pressing the
PROGRESSIVE button on the front panel.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
16
Notes
• Do not connect a VCR, etc., between your TV and the player. If you pass the player signals via the VCR,
you may not receive a clear image on the TV screen. If your TV has only one audio/video input jack,
connect the player to this jack.
CD/DVD player
Hookups
VCR
TV
Connect
directly
• Consumers should note that not all high definition television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In case of 525 or 625 progressive scan picture problems,
it is recommended that the user switch the connection to the ‘standard definition’ output. If there are
questions regarding your TV set compatibility with this 525p and 625p DVD player model, please contact
our customer service centre.
• When you connect the player to your TV via the SCART jacks, the TV’s input source is set to the player
automatically when you start playback. In this case, press t (TV/video) on the remote to return the input
to the TV.
• If you set “LINE” in SCREEN SETUP to “RGB” (page 21, 65), the player outputs no component video
signals.
When you play a disc recorded in the NTSC colour system, the player outputs the video signal
or the Setup Display etc. in the NTSC colour system and the picture may not appear on the
PAL colour system televisions. In this case, open the tray and remove the disc.
Using the PROGRESSIVE button
By using the PROGRESSIVE button on the front panel, you can select the signal format in
which the player outputs video signals (Progressive or Interlace), and the conversion method for
progressive signals. The PROGRESSIVE indicator lights up when the player outputs
progressive signals.
Each time you press the PROGRESSIVE button, the display changes as follows:
PROGRESSIVE AUTO
m
PROGRESSIVE VIDEO
m
NORMAL (INTERLACE)
◆PROGRESSIVE AUTO
Select this setting when:
– your TV accepts progressive signals, and,
– the TV is connected to the COMPONENT VIDEO OUT jacks.
Normally select this under the above condition. This automatically detects the software type, and
selects the appropriate conversion method.
Note that the picture will not be clear or no picture will appear if you select these settings when
either of the above conditions is not met.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
17
◆PROGRESSIVE VIDEO
Select this setting when:
– your TV accepts progressive signals, and,
– the TV is connected to the COMPONENT VIDEO OUT jacks, and
– you want to fix the conversion method to PROGRESSIVE VIDEO for video-based software.
Select this if the image is not clear when you select PROGRESSIVE AUTO.
Note that the picture will not be clear or no picture will appear if you select these settings when
either of the above conditions is not met.
◆NORMAL (INTERLACE)
Select this setting when:
– your TV does not accept progressive signals, or,
– your TV is connected to jacks other than the COMPONENT VIDEO OUT jacks (LINE OUT
(VIDEO) or S VIDEO OUT).
◆About DVD software types and the conversion method
DVD software can be divided into two types: film-based software and video-based software.
Video-based software is derived from TV, such as dramas and sit-coms, and displays images at
25 frames/50 fields (30 frames/60 fields) per second. Film-based software is derived from film
and displays images at 24 frames per second. Some DVD software contains both video and film.
In order for these images to appear natural on your screen when output in progressive format,
the progressive signals need to be converted to match the type of DVD software that you are
watching.
Notes
• When you play video-based software in progressive signal format, sections of some types of images may
appear unnatural due to the conversion process when output through the COMPONENT VIDEO OUT
jacks. Images from the S VIDEO OUT and LINE OUT (VIDEO) jacks are unaffected as they are output in
the normal (interlace) format.
• If you set “LINE” in “SCREEN SETUP” to “RGB,” then the player switches to “NORMAL
(INTERLACE).” This will happen even though you select “PROGRESSIVE AUTO” or “PROGRESSIVE
VIDEO.”
• When using LINE OUT (VIDEO) or S VIDEO OUT, the picture may appear to flicker each time the
PROGRESSIVE button on the front panel is pressed (Interlace switches to Progressive or vice versa).
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
18
Step 4: Connecting the Audio Cords
(red)
(yellow)*
Audio/video
cord (supplied)
A
INPUT
Hookups
Select one of the following patterns A or B, according to the input jack on your TV monitor,
projector, or AV amplifier (receiver).
This will enable you to listen to sound.
VIDEO
(white)
(white)
(yellow)*
(red)
L
AUDIO
R
TV, projector, or AV
amplifier (receiver)
LINE OUT
VIDEO
R
AUDIO
L
to LINE OUT L/R (AUDIO)
LINE OUT
VIDEO
COAXIAL
R
Y
OPTICAL
DIGITAL OUT
PB/CB
AUDIO
L
LINE
(RGB)
-TV
L
CENTER
PR/CR
COMPONENT VIDEO OUT
S VIDEO OUT
CD/DVD player
to DIGITAL OUT
(COAXIAL or OPTICAL)
COAXIAL
or
Coaxial digital cord
(not supplied)
OPTICAL
DIGITAL OUT
Optical digital cord (not supplied)
Remove jack cap before connecting
[Speakers]
to optical
digital input
to coaxial
digital input
Rear (L)
Rear (R)
Front (L)
Center
B
[Speakers]
Front (R)
AV amplifier (receiver)
with a decoder
Subwoofer
: Signal flow
* The yellow plug is used for video signals (page 15).
z Hint
For correct speaker location, see the operating instructions supplied with the connected components.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
19
A Connecting to audio L/R input
B Connecting to a digital audio
jacks
input jack
This connection will use your TV’s or stereo
amplifier’s (receiver’s) two speakers for
sound. Connect using the audio/video cord
(supplied).
If your AV amplifier (receiver) has a Dolby*1
Digital or DTS*2 or MPEG audio decoder
and a digital input jack, use this connection.
Connect using a coaxial or optical digital cord
(not supplied).
Yellow
White (L)
Yellow
White (L)
Coaxial cord
Red (R)
Red (R)
Optical cord
• Surround effect (page 43)
TV: Dynamic Theatre, Dynamic, Wide,
Night
• Surround effect
Dolby Digital (5.1ch), DTS (5.1ch), MPEG
audio (5.1ch)
Stereo amplifier (receiver): Standard, Night
*1
*2
Manufactured under license from Dolby
Laboratories.
“Dolby,” “Pro Logic,” and the double-D symbol
are trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
Notes
• After you have completed the connection, make
the appropriate settings in Quick Setup (page 21).
If your AV amplifier (receiver) has an MPEG
audio decoder function, set “MPEG” to “MPEG”
in Audio Setup (page 68). Otherwise, no sound or
a loud noise will come from your speakers.
• The surround sound effects of this player cannot
be used with this connection.
• In order to listen to DTS sound tracks, you must
use this connection. DTS sound tracks are not
output through the LINE OUT L/R (AUDIO)
jacks, even if you set “DTS” to “ON” in Quick
Setup (page 21).
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
20
Step 5: Connecting the Mains Lead
Plug the player and TV mains lead (power cord) into a mains.
Hookups
Step 6: Quick Setup
Follow the steps below to make the minimum number of basic adjustments for using the player.
To skip an adjustment, press >. To return to the previous adjustment, press ..
ENTER
1 Turn on the TV.
2 Press [/1.
3 Switch the input selector on your
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
TV so that the signal from the
player appears on the TV screen.
“Press [ENTER] to run QUICK SETUP”
(press enter to run Quick Setup) appears
at the bottom of the screen. If this
message does not appear, select
“QUICK” (quick) under “SETUP”
(setup) in the Control Menu to run Quick
Setup (page 64).
4 Press ENTER without inserting a
disc.
The Setup Display for selecting the
language used in the on-screen display
appears.
ENGLISH
ENGLISH
FRANÇAIS
DEUTSCH
ITALIANO
ESPAÑOL
NEDERLANDS
DANSK
SVENSKA
5 Press X/x to select a language.
The player displays the menu and
subtitles in the selected language.
6 Press ENTER.
The Setup Display for selecting the
aspect ratio of the TV to be connected
appears.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
4:3 OUTPUT:
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
16:9
16:9
4:3 LETTER BOX
4:3 PAN SCAN
FULL
,continued
21
7 Press X/x to select the setting that 11Press X/x to select the type of
matches your TV type.
◆ If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
• 16:9 (page 65)
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
(page 65)
8 Press ENTER.
The Setup Display for selecting the type
of video signal output from the LINE
(RGB)-TV jack appears.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
4:3 OUTPUT:
16:9
ON
JACKET PICTURE
VIDEO
VIDEO
S VIDEO
RGB
9 Press X/x to select the type of
signal you want to output from the
LINE (RGB)-TV jack.
◆ Video signals
• VIDEO (page 65)
◆ S video signals
• S VIDEO (page 65)
◆ RGB signals
• RGB (page 65)
When you select “RGB,” you will be
unable to use the PROGRESSIVE
button, and the player will not output
video signals from the COMPONENT
VIDEO OUT jacks.
10Press ENTER.
The Setup Display for selecting the type
of jack used to connect your amplifier
(receiver) appears.
Is this player connected to an amplifier
(receiver) ? Select the type of jack you
are using.
YES
LINE OUTPUT L/R (AUDIO)
DIGITAL OUTPUT
NO
jack (if any) you are using to
connect to an amplifier (receiver),
then press ENTER.
If you did not connect an AV amplifier
(receiver), select “NO,” then go to step
15.
If you connected an AV amplifier
(receiver) using just an audio cord, select
“YES: LINE OUTPUT L/R (AUDIO),”
then go to step 15.
If you connected an AV amplifier
(receiver) using either a optical or coaxial
digital cord, select “YES: DIGITAL
OUTPUT.”
12Press X/x to select the type of
Dolby Digital signal you wish to
send to your amplifier (receiver).
If your AV amplifier (receiver) has a
Dolby Digital decoder, select “DOLBY
DIGITAL.” Otherwise, select “D-PCM.”
AUDIO SETUP
OFF
AUDIO ATT:
STANDARD
AUDIO DRC:
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
ON
D-PCM
DOLBY DIGITAL:
MPEG:
D-PCM
DTS:
DOLBY DIGITAL
48kHz/96kHz PCM:
48kHz/16bit
13Press ENTER.
“DTS” is selected.
AUDIO SETUP
AUDIO ATT:
OFF
AUDIO DRC:
STANDARD
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
ON
D-PCM
DOLBY DIGITAL:
MPEG:
PCM
DTS:
OFF
48kHz/96kHz PCM:
OFF
ON
14Press X/x to select whether or
not you wish to send a DTS signal
to your amplifier (receiver).
If your AV amplifier (receiver) has a
DTS decoder, select “ON.” Otherwise,
select “OFF.”
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
22
15Press ENTER.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
Hookups
Quick Setup is finished. All connections
and setup operations are complete.
If your AV amplifier (receiver) has an
MPEG audio decoder, set “MPEG” to
“MPEG” (page 68).
23
4 Press A on the player, and place a
disc on the disc tray.
Playing Discs
Playing Discs
Depending on the DVD or VIDEO CD, some
operations may be different or restricted.
Refer to the operating instructions supplied
with your disc.
Playback side facing down
5 Press H.
The disc tray closes. The player starts
playback (continuous play). Adjust the
volume on the TV or the amplifier
(receiver).
Depending on the disc, a menu may
appear on the TV screen. For DVD
VIDEOs, see page 27. For VIDEO CDs,
see page 28.
To turn off the player
Press [/1. The player enters standby mode.
ENTER
RETURN
z Hint
You can have the player turn off automatically
whenever you leave it in stop mode for more than
30 minutes. To turn this function on or off, set
“AUTO POWER OFF” in “CUSTOM SETUP” to
“ON” or “OFF” (page 66).
Notes on playing DTS sound tracks on a
DVD VIDEO
1 Turn on your TV.
2 Press [/1.
The player turns on.
3 Switch the input selector on your
TV so that the signal from the
player appears on the TV screen.
◆ When using an amplifier (receiver)
Turn on the amplifier (receiver) and
select the appropriate channel so that you
can hear sound from the player.
• DTS audio signals are output only through the
DIGITAL OUT (COAXIAL or OPTICAL) jack.
• When you play a DVD VIDEO with DTS sound
tracks, set “DTS” to “ON” in “AUDIO SETUP”
(page 69).
• If you connect the player to audio equipment
without a DTS decoder, do not set “DTS” to “ON”
in “AUDIO SETUP” (page 69). A loud noise may
come out from the speakers, affecting your ears or
causing the speakers to be damaged.
Note
Discs created on DVD recorders must be correctly
finalized before they can be played. For more
information about finalizing, refer to the operating
instructions supplied with the DVD recorder.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
24
Additional operations
Note
You may not be able to use the Replay or Advance
function with some scenes.
Playback quickly or slowly with
sound
(replay)
(advance)
During playback, press FAST PLAY or
SLOW PLAY.
The speed changes when you press either
FAST PLAY or SLOW PLAY.
ZOOM
Playing Discs
You can listen to dialogue or sound while
playing the current scene quickly or slowly.
CLEAR
To return to normal playback
SLOW PLAY
FAST PLAY
To
Operation
Stop
Press x
Pause
Press X
Resume play after
pause
Press X or H
Press H.
Notes
Press .
Go back to the
previous chapter,
track, or scene in
continuous play mode
• You can only use this function with DVDs/
VIDEO CDs/Super VCDs and DVD-RWs in VR
mode only.
• “Operation not possible” will appear when
maximum or minimum speed is reached.
• During FAST PLAY and SLOW PLAY mode,
you cannot change angle (page 45), subtitle (page
45), and the sound (page 41). The sound can only
be changed for VIDEO CDs/Super VCDs.
• Fast Play and Slow Play functions do not work
when playing DTS sound tracks.
• You cannot use Fast Play and Slow Play function
when playing a still picture on DVD-RW in VR
mode.
Stop play and remove Press Z
the disc
Locking the disc tray (Child Lock)
Replay the previous
scene*1
Press
(replay) during
playback
You can lock the disc tray to prevent children
from opening it.
Briefly fast forward
the current scene*2
Press
(advance) during
playback
Magnify the image*3
Press ZOOM
repeatedly. Press
CLEAR to cancel.
Go to the next chapter, Press >
track, or scene in
continuous play mode
*1 DVD VIDEOs/DVD-RWs/DVD-Rs only. The
button can be used except for DivX video files.
*2 DVD VIDEOs/DVD-RWs/DVD-Rs/
DVD+RWs/DVD+Rs only. The button can be
used except for DivX video files.
*3 Video and JPEG pictures only (except
BACKGROUND pictures). You can move the
enlarged picture using C/X/x/c. Depending
upon the contents of the disc, the zoom function
may be cancelled automatically when the
picture is moved.
When the player is in standby mode, press
O RETURN, ENTER, and then [/1 on the
remote.
The player turns on and “LOCKED” appears
on the front panel display. The A and Z
buttons on the player or the remote do not
work while the Child Lock is set.
To unlock the disc tray
When the player is in standby mode, press
O RETURN, ENTER, and then [/1 again.
Note
Even if you select “RESET” under “SETUP” in the
Control Menu (page 64), the disc tray remains
locked.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
25
Resuming Playback From
the Point Where You
Stopped the Disc (Multi-disc
Resume)
The player stores the point where you stopped
the disc for up to 6 discs and resumes
playback the next time you insert the same
disc. If you store a resume playback point for
the seventh disc, the resume playback point
for the first disc is deleted.
Notes
• “MULTI-DISC RESUME” in “CUSTOM
SETUP” must be set to “ON” (default) for this
function to work (page 67).
• The point where you stopped playing is cleared
when:
– you change the play mode.
– you change the settings on the Setup Display.
• For DVD-RWs in VR mode, CDs, DATA CDs,
and DATA DVDs, the player remembers the
resume playback point for the current disc.
The resume point is cleared when:
– you opened the disc tray.
– you disconnect the power cord (CD or DATA
CD/DATA DVD only).
– the player enters standby mode (DATA CD/
DATA DVD only).
• Resume Play does not work during Shuffle Play
and Programme Play.
• This function may not work with some discs.
• If “MULTI-DISC RESUME” in “CUSTOM
SETUP” is set to “ON” and you playback a
recorded disc such as DVD-RW, the player may
playback other recorded discs from the same
resume point. To play from the beginning, press
x twice and then press H.
1 While playing a disc, press x to
stop playback.
“RESUME” appears on the front panel
display.
2 Press H.
The player starts playback from the point
where you stopped the disc in step 1.
z Hint
To play from the beginning of the disc, press x
twice, then press H.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
26
Using the DVD’s Menu
Some DVD-RWs in VR (Video Recording)
mode have two types of titles for playback:
originally recorded titles (ORIGINAL) and
titles that can be created on recordable DVD
players for editing (PLAY LIST). You can
select the type of title to be played.
Playing Discs
A DVD is divided into long sections of a
picture or a music feature called “titles.”
When you play a DVD which contains
several titles, you can select the title you want
using the TOP MENU button.
When you play DVDs that allow you to select
items such as language for the sound and
subtitles, select these items using the MENU
button.
Selecting “ORIGINAL” or
“PLAY LIST” on a DVDRW
Number
buttons
ENTER
TOP MENU
MENU
ENTER
DISPLAY
1 Press DISPLAY when the player is
in stop mode.
The Control Menu appears.
1 Press TOP MENU or MENU.
The disc’s menu appears on the TV
screen.
The contents of the menu vary from disc
to disc.
2 Press C/X/x/c or the number
buttons to select the item you want
to play or change.
2 Press X/x to select
(ORIGINAL/PLAY LIST), then press
ENTER.
The options for “ORIGINAL/PLAY
LIST” appear.
12(27)
18(34)
T
1:32:55
PLAY LIST
PLAY LIST
ORIGINAL
DVD-RW
If you press the number buttons, the
following display appears.
Press the number buttons to select the
item you want.
1
3 Press X/x to select a setting.
• PLAY LIST: plays the titles created
from “ORIGINAL” for editing.
• ORIGINAL: plays the titles originally
recorded.
3 Press ENTER.
4 Press ENTER.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
27
Playing VIDEO CDs With
PBC Functions (PBC Playback)
PBC (Playback Control) allows you to play
VIDEO CDs interactively by following the
menu on the TV screen.
z Hint
To play without using PBC, press ./> or the
number buttons while the player is stopped to select
a track, then press H or ENTER.
“Play without PBC” appears on the TV screen and
the player starts continuous play. You cannot play
still pictures such as a menu.
To return to PBC playback, press x twice then
press H.
Note
Depending on the VIDEO CD, “Press ENTER” in
step 3 may appear as “Press SELECT” in the
instructions supplied with the disc. In this case,
press H.
Number
buttons
ENTER
RETURN
1 Start playing a VIDEO CD with PBC
functions.
The menu for your selection appears.
2 Press the number buttons to select
the item number you want.
3 Press ENTER.
4 Follow the instructions in the
menu for interactive operations.
Refer to the instructions supplied with the
disc, as the operating procedure may
differ depending on the VIDEO CD.
To return to the menu
Press O RETURN.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
28
12(27)
18(34)
T
1:32:55
OFF
OFF
SET
ON
Various Play Mode
Functions (Programme Play,
Shuffle Play, Repeat Play, A-B Repeat
PLAY
DVD VIDEO
Play)
3
Press X/x to select “SET t,” then
press ENTER.
“TRACK” is displayed when you play
a VIDEO CD or CD.
PROGRAM
CLEAR
ALL CLEAR
1. TITLE
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
ENTER
Playing Discs
You can set the following play modes:
• Programme Play (page 29)
• Shuffle Play (page 30)
• Repeat Play (page 31)
• A-B Repeat Play (page 32)
T
––
01
02
03
04
05
Titles or tracks
recorded on a disc
DISPLAY
4
Press c.
The cursor moves to the title or track row
“T” (in this case, “01”).
PROGRAM
ALL CLEAR
1. TITLE – –
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
Note
The play mode is cancelled when:
– you eject the disc.
– the player enters standby mode by pressing [/1.
Creating your own programme
(Programme Play)
You can play the contents of a disc in the
order you want by arranging the order of the
titles, chapters, or tracks on the disc to create
your own programme. You can programme
up to 99 titles, chapters, and tracks.
1
Press DISPLAY.
The Control Menu appears.
2
Press X/x to select
(PROGRAM), then press ENTER.
The options for “PROGRAM” appear.
T
C
––
01
02
03
04
05
ALL
01
02
03
04
05
06
Chapters recorded on a disc
5
Select the title, chapter, or track you
want to programme.
◆ When playing a DVD VIDEO
For example, select chapter “03” of title
“02.”
Press X/x to select “02” under “T,” then
press ENTER.
PROGRAM
ALL CLEAR
1. TITLE – –
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
T
C
––
01
02
03
04
05
ALL
01
02
03
04
05
06
,continued
29
Next, press X/x to select “03” under “C,”
then press ENTER.
PROGRAM
ALL CLEAR
1. TITLE 0 2 – 0 3
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
T
––
01
02
03
04
05
Selected title and chapter
◆ When playing a VIDEO CD or CD
For example, select track “02.”
Press X/x to select “02” under “T,” then
press ENTER.
3
Follow step 5 for new programming. To
cancel a programme, select “--” under
“T,” then press ENTER.
To cancel all of the titles, chapters, or
tracks in the programmed order
1
Follow steps 1 to 3 of “Creating your own
programme (Programme Play).”
2
3
Press X and select “ALL CLEAR.”
Press ENTER.
z Hint
You can perform Repeat Play or Shuffle Play of
programmed titles, chapters, or tracks. During
Programme Play, follow the steps of Repeat Play
(page 31) or Shuffle Play (page 30).
Selected track
0:15:30
T
PROGRAM
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
02
––
––
––
––
––
––
––
01
02
03
04
05
Notes
• When you programme tracks on a Super VCD, the
total playing time is not displayed.
• You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
Playing in random order (Shuffle
Play)
Total time of the programmed tracks
6
7
To programme other titles, chapters,
or tracks, repeat steps 4 to 5.
You can have the player “shuffle” titles,
chapters, or tracks. Subsequent “shuffling”
may produce a different playing order.
The programmed titles, chapters, and
tracks are displayed in the selected order.
1
Press H to start Programme Play.
2
Programme Play begins.
When the programme ends, you can
restart the same programme again by
pressing H.
The Control Menu appears.
12(27)
18(34)
T
1:32:55
Follow steps 1 to 3 of “Creating your
own programme (Programme Play).”
2
Select the programme number of the title,
chapter, or track you want to change or
cancel using X/x and press c. If you
want to delete the title, chapter, or track
from the programme, press CLEAR.
3
Press X/x to select the item to be
shuffled.
◆ When playing a DVD VIDEO
• TITLE
• CHAPTER
◆ When playing a VIDEO CD or CD
• TRACK
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
30
PLAY
DVD VIDEO
OFF
OFF
TITLE
CHAPTER
Press CLEAR, or select “OFF” in step 3. To
play the same programme again, select “ON”
in step 3 and press ENTER.
1
Press X/x to select
(SHUFFLE), then press ENTER.
The options for “SHUFFLE” appear.
To return to normal play
To change or cancel a programme
Press DISPLAY during playback.
◆ When playing a DVD-RW
• DISC: repeats all the titles of the
selected type.
• TITLE: repeats the current title on a
disc.
• CHAPTER: repeats the current chapter.
◆ When Programme Play is activated
• ON: shuffles titles, chapters, or tracks
selected in Programme Play.
4
Press ENTER.
Shuffle Play starts.
◆ When playing a VIDEO CD or CD
• DISC: repeats all of the tracks.
• TRACK: repeats the current track.
To return to normal play
◆ When playing a DATA CD/DATA DVD
• DISC: repeats all of the albums.
• ALBUM: repeats the current album.
• TRACK (MP3 audio tracks only):
repeats the current track.
• FILE (DivX video files only): repeats
the current file.
z Hints
• You can set Shuffle Play while the player is
stopped. After selecting the “SHUFFLE” option,
press H. Shuffle Play starts.
• Up to 200 chapters in a disc can be played in
random order when “CHAPTER” is selected.
◆ When Programme Play or Shuffle Play
is activated
• ON: repeats Programme Play or Shuffle
Play.
Note
You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
Playing repeatedly (Repeat Play)
You can play all of the titles or tracks on a
disc, or a single title, chapter, or track
repeatedly.
You can use a combination of Shuffle or
Programme Play modes.
1
Press DISPLAY during playback.
The Control Menu appears.
2
Press X/x to select
(REPEAT), then press ENTER.
The options for “REPEAT” appear.
12(27)
18(34)
T
1:32:55
PLAY
DVD VIDEO
OFF
OFF
DISC
TITLE
CHAPTER
Playing Discs
Press CLEAR, or select “OFF” in step 3.
3
Press X/x to select a setting, and
press ENTER.
To return to normal play
Press CLEAR, or select “OFF” in step 2.
z Hint
You can set Repeat Play while the player is stopped.
After selecting the “REPEAT” option, press H.
Repeat Play starts.
Notes
• You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
• When repeating a DATA CD/DATA DVD which
contains MP3 audio tracks and JPEG image files,
and their playing times are not the same, the sound
will not match the image.
• When “MODE (MP3, JPEG)” is set to “IMAGE
(JPEG)” (page 53), you cannot select “TRACK.”
◆ When playing a DVD VIDEO
• DISC: repeats all of the titles.
• TITLE: repeats the current title on a
disc.
• CHAPTER: repeats the current chapter.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
31
Repeating a specific portion (AB Repeat Play)
You can play a specific portion of a title,
chapter or track repeatedly. (This function is
useful when you want to memorize lyrics,
etc.)
1
Notes
• When you set A-B Repeat Play, the settings for
Shuffle Play, Repeat Play, and Programme Play
are cancelled.
• A-B Repeat Play does not work across multiple
titles.
• You may not set A-B Repeat Play for contents on
a DVD-RW (VR mode) that contains still
pictures.
Press DISPLAY during playback.
The Control Menu appears.
2
Press X/x to select
(A-B
REPEAT), then press ENTER.
The options for “A-B REPEAT” appear.
12(27)
18(34)
T
1:32:55
PLAY
DVD VIDEO
OFF
SET
OFF
3
Press X/x to select “SET t,” then
press ENTER.
The “A-B REPEAT” setting bar appears.
A 18 - 1:32:30
4
B
During playback, when you find the
starting point (point A) of the portion to
be played repeatedly, press ENTER.
The starting point (point A) is set.
A 18 - 1:32:30
5
B 18 - 1:33:05
When you reach the ending point
(point B), press ENTER again.
The set points are displayed and the
player starts repeating this specific
portion.
To return to normal play
Press CLEAR, or select “OFF” in step 3.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
32
Searching for a Scene
Searching for a
Particular Point on a
Disc (Search, Scan, Slow-motion
Play, Freeze Frame)
You can search for the next or previous
chapter, track, or scene using ./> on
the player.
During playback, press > or . once
briefly to go to the next or previous chapter/
track/scene. Or, press and hold > or .
to search forward or backwards, and release
the button when you find the point you want
to return to normal playback. (Search)
Locating a point quickly by
playing a disc in fast forward or
fast reverse (Scan)
(step)
(step)
Searching for a Scene
You can quickly locate a particular point on a
disc by monitoring the picture or playing back
slowly.
Locating a point quickly using
the previous/next buttons
(Search)
Press
m or M
while playing a
disc. When you find the point you want, press
H to return to normal speed. Each time you
press
m or M
during scan, the
scan speed changes. With each press the
indication changes as shown below. Actual
speeds may differ between discs.
Playback direction
×2B t 1M t 2M t 3M
3M (DVD VIDEO/DVD-RW/VIDEO CD/DATA
CD*/DATA DVD* only)
×2B (DVD VIDEO/CD only)
Notes
• Depending on the disc, you may not be able to do
some of the operations described.
• For DATA CDs/DATA DVDs, you can search for
a particular point only on MP3 audio track or
DivX video file.
Opposite direction
×2b t 1m t 2m t 3m
3m (DVD VIDEO/DVD-RW/VIDEO CD/DATA
CD*/DATA DVD* only)
×2b (DVD VIDEO only)
* DivX video only
The “×2B”/ “×2b” playback speed is about
twice the normal speed.
The “3M”/“3m” playback speed is faster
than “2M”/“2m” and the “2M”/“2m”
playback speed is faster than “1M”/
“1m.”
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
33
Watching frame by frame
(Slow-motion Play)
Press
m or M
when the player is
in pause mode. To return to normal speed,
press H.
Each time you press
m or M
during Slow-motion Play, the playback speed
changes. Two speeds are available. With each
press the indication changes as follows:
Playback direction
2
y1
Searching for a Title/
Chapter/Track/Scene,
etc.
You can search a DVD by title or chapter, and
you can search a VIDEO CD/CD/DATA CD/
DATA DVD by track, index, or scene. As
titles and tracks are assigned unique numbers
on the disc, you can select the desired one by
entering its number. You can also search for a
scene using the time code.
Opposite direction (DVD VIDEO/DVD-RW
only)
2
y1
The “2 y”/“2
than “1 y”/“1
” playback speed is slower
.”
Number
buttons
CLEAR
Note
ENTER
For DATA CDs/DATA DVDs, this function works
only for DivX video files.
DISPLAY
Playing one frame at a time
(Freeze Frame)
When the player is in the pause mode, press
(step) to go to the next frame. Press
(step) to go to the preceding frame
(DVD VIDEO/DVD-RW only). To return to
normal playback, press H.
1 Press DISPLAY (When playing a
DATA CD/DATA DVDs with JPEG
image files, press twice).
The Control Menu appears.
Notes
• You cannot search for a still picture on a DVDRW in VR mode.
• For DATA CDs/DATA DVDs, this function
works only for DivX video files.
2 Press X/x to select the search
method.
◆ When playing a DVD VIDEO/DVD-RW
TITLE
CHAPTER
TIME/TEXT
Select “TIME/TEXT” to search for a
starting point by inputting the time code.
◆ When playing a VIDEO CD or Super
VCD without PBC playback
TRACK
INDEX
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
34
◆ When playing a VIDEO CD or Super
VCD with PBC Playback
5 Press ENTER.
The player starts playback from the
selected number.
SCENE
◆ When playing a CD
TRACK
◆ When playing a DATA CD/DATA DVD
ALBUM
TRACK (MP3 audio tracks
To search for a scene using the time code
(DVD VIDEO/DVD-RW only)
In step 2, select
TIME/TEXT.
“T **:**:**” (playing time of the current
title) is selected.
2
Press ENTER.
“T **:**:**” changes to “T --:--:--.”
Input the time code using the number
buttons, then press ENTER.
For example, to find the scene at 2 hours,
10 minutes, and 20 seconds after the
beginning, just enter “2:10:20.”
only)
FILE (JPEG image files only)
◆ When playing a DATA CD/DATA DVD
(DivX video files)
ALBUM
FILE
Example: when you select
CHAPTER
“** (**)” is selected (** refers to a
number).
The number in parentheses indicates the
total number of titles, chapters, tracks,
indexes, scenes, albums or files.
12(27)
18(34)
T
1:32:55
PLAY
DVD VIDEO
3
Searching for a Scene
1
z Hints
• When the Control Menu display is turned off, you
can search for a chapter (DVD VIDEO/DVDRW), track (CD/DATA CD/DATA DVD), or file
(DATA CD/DATA DVD (DivX video)) by
pressing the number buttons and ENTER.
• You can display the first scene of titles, chapters,
or tracks recorded on the disc on a screen divided
into 9 sections. You can start playback directly by
selecting one of the scenes. For details, see
“Searching by Scene (PICTURE
NAVIGATION)” (page 36).
Selected row
Notes
3 Press ENTER.
“** (**)” changes to “-- (**).”
12(27)
(34)
T
1:32:55
• The title, chapter, or track number displayed is the
same number recorded on the disc.
• You cannot search for a scene on a DVD+RW/
DVD+R using the time code.
PLAY
DVD VIDEO
4 Press the number buttons to select
the title, chapter, track, index, or
scene, etc. number you want to
search.
◆ If you make a mistake
Cancel the number by pressing CLEAR,
then select
number.
Downloaded
Fromanother
DvDPlayer-Manual.com
Sherwood Manuals
35
Searching by Scene
(PICTURE NAVIGATION)
You can divide the screen into 9 subscreens
and find the desired scene quickly.
1
2
3
4
5
6
7
8
9
4 Press C/X/x/c to select a chapter,
title, or track, and press ENTER.
PICTURE
NAVI
ENTER
RETURN
DISPLAY
1 Press PICTURE NAVI during
playback.
The following display appears.
CHAPTER VIEWER
ENTER
Playback starts from the selected scene.
To return to normal play during setting
Press O RETURN or DISPLAY.
z Hint
If there are more than 9 chapters, titles, or tracks, V
is displayed at the bottom right of the screen.
To display the additional chapters, titles, or tracks,
select the bottom scenes and press x. To return to
the previous scene, select the top scenes and press
X.
Note
Depending on the disc, you may not be able to select
some items.
2 Press PICTURE NAVI repeatedly to
select an item.
• CHAPTER VIEWER (DVD VIDEO
only): displays the first scene of each
chapter.
• TITLE VIEWER (DVD VIDEO only):
displays the first scene of each title.
• TRACK VIEWER (VIDEO CD/
Super VCD only): displays the first
scene of each track.
3 Press ENTER.
The first scene of each chapter, title, or
track appears as follows.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
36
Viewing Information About the
Disc
Checking the Playing
Time and Remaining
Time
TIME/TEXT
◆ When playing a VIDEO CD or Super
VCD (with PBC functions)
• *:* (minutes: seconds)
Playing time of the current scene
◆ When playing a VIDEO CD (without
PBC functions) or CD
• T *:* (minutes: seconds)
Playing time of the current track
• T–*:*
Remaining time of the current track
• D *:*
Playing time of the current disc
• D –*:*
Remaining time of the current disc
◆ When playing a Super VCD (without
PBC functions)
• T *:* (minutes: seconds)
Playing time of the current track
1 Press TIME/TEXT during playback.
The following display appears.
T 1:01:57
Viewing Information About the Disc
You can check the playing time and
remaining time of the current title, chapter, or
track. Also, you can check the DVD/CD text,
track name (MP3 audio), or file name (DivX
video) recorded on the disc.
◆ When playing a DVD VIDEO or DVDRW
• T *:*:* (hours: minutes: seconds)
Playing time of the current title
• T–*:*:*
Remaining time of the current title
• C *:*:*
Playing time of the current chapter
• C–*:*:*
Remaining time of the current chapter
◆ When playing a DATA CD or DATA DVD
(MP3 audio)
• T *:* (minutes: seconds)
Playing time of the current track
◆ When playing a DATA CD or DATA DVD
(DivX video)
• *:*:* (hours: minutes: seconds)
Playing time of the current file
Time
information
2 Press TIME/TEXT repeatedly to
change the time information.
The available time information depends
upon the type of disc you are playing.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
37
Checking the play information of
the disc
Checking the information on the
front panel display
To check the DVD/CD text
You can view the time information and text
displayed on the TV screen also on the front
panel display. The information on the front
panel display changes as follows when you
change the time information on your TV
screen.
Press TIME/TEXT repeatedly in step 2 to
display text recorded on the DVD/CD.
The DVD/CD text appears only when text is
recorded in the disc. You cannot change the
text. If the disc does not contain text, “NO
TEXT” appears.
When playing a DVD VIDEO or DVD-RW
Playing time of the current title
BRAHMS SYMPHONY
To check DATA CD/DATA DVD (MP3 audio
or DivX video) album name, etc.
By pressing TIME/TEXT while playing MP3
audio tracks on a DATA CD/DATA DVD or
DivX video files on a DATA CD/DATA
DVD, you can display the name of the album/
track/file and the audio bit rate (the amount of
data per second of the current audio track) on
your TV screen.
Bit rate*
T
17:30
Remaining time of the current title
Playing time of the current chapter
Remaining time of the current
chapter
128k
Text
JAZZ
RIVER SIDE
Album name
Current title and chapter number
Track/file name
(returns to top automatically)
* Appears when:
– playing an MP3 audio track on a DATA CD/
DATA DVD.
– playing a DivX video file that contains MP3
audio on a DATA CD/DATA DVD.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
38
When playing a DATA CD/DATA DVD (MP3
audio)
When playing a VIDEO CD (without PBC
functions), or CD
Playing time and number of the
current track
Playing time and number of the
current track
Track name
Remaining time of the current
track
Current album and track number
Playing time of the disc
When playing a DATA CD (DivX video), or
DATA DVD (DivX video)
Viewing Information About the Disc
(returns to top automatically)
Remaining time of the disc
Playing time of the current file
The current file name
The current album and file number
(returns to top automatically)
Text
Current track and index number*
(returns to top automatically)
* The current track and index number appear only
when playing a VIDEO CD.
z Hints
• When playing VIDEO CDs without PBC
functions, the track number and the index number
are displayed after the text.
• When playing VIDEO CDs with PBC functions,
the scene number or the playing time are
displayed.
• Long text that does not fit in a single line will
scroll across the front panel display.
• You can also check the time information and text
using the Control Menu (page 11).
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
39
Notes
• Depending on the type of disc being played, the
DVD/CD discs text or track name may not be
displayed.
• The player can only display the first level of the
DVD/CD text, such as the disc name or title.
• Playing time of MP3 audio tracks and DivX video
files may not be displayed correctly.
• If you play a disc containing JPEG image files
only, “NO AUDIO DATA” appears when
“MODE (MP3, JPEG)” is set to “AUTO,”
“JPEG” appears when “MODE (MP3, JPEG)” is
set to “IMAGE (JPEG)” in the front panel display.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
40
Sound Adjustments
Changing the Sound
◆ When playing a DVD-RW
The types of sound tracks recorded on a
disc are displayed. The default setting is
underlined.
Example:
• 1: MAIN (main sound)
• 1: SUB (sub sound)
• 1: MAIN+SUB (main and sub sound)
◆ When playing a VIDEO CD, CD, DATA
CD or DATA DVD (MP3 audio)
The default setting is underlined.
• STEREO: the standard stereo sound
• 1/L: the sound of the left channel
(monaural)
• 2/R: the sound of the right channel
(monaural)
Sound Adjustments
When playing a DVD VIDEO or DATA CD/
DATA DVD (DivX video files) recorded in
multiple audio formats (PCM, Dolby Digital,
MPEG audio, or DTS), you can change the
audio format. If the DVD VIDEO is recorded
with multilingual tracks, you can also change
the language.
With CDs, DATA CDs, DATA DVDs or
VIDEO CDs, you can select the sound from
either the right or left channel and listen to the
sound of the selected channel through both
the right and left speakers. For example, when
playing a disc containing a song with the
vocals on the right channel and the
instruments on the left channel, you can hear
the instruments from both speakers by
selecting the left channel.
◆ When playing a DVD VIDEO
Depending on the DVD VIDEO, the
choice of language varies.
When 4 digits are displayed, they
indicate a language code. See “Language
Code List” on page 76 to see which
language the code represents. When the
same language is displayed two or more
times, the DVD VIDEO is recorded in
multiple audio formats.
◆ When playing a DATA CD (DivX
video), or DATA DVD (DivX video)
Select one of the displayed audio signal
formats. If “No audio data” appears, the
player does not support the audio signal
format contained in the disc.
1 Press
(audio) during playback.
The following display appears.
1:ENGLISH DOLBY DIGITAL 3/2.1
◆ When playing a Super VCD
The default setting is underlined.
• 1:STEREO: the stereo sound of the
audio track 1
• 1:1/L: the sound of the left channel of
the audio track 1 (monaural)
• 1:2/R: the sound of the right channel of
the audio track 1 (monaural)
• 2:STEREO: the stereo sound of the
audio track 2
• 2:1/L: the sound of the left channel of
the audio track 2 (monaural)
• 2:2/R: the sound of the right channel of
the audio track 2 (monaural)
2 Press
(audio) repeatedly to
select the desired audio signal.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
41
About audio signals
Notes
• While playing a Super VCD on which the audio
track 2 is not recorded, no sound will come out
when you select “2:STEREO,” “2:1/L,” or “2:2/
R.”
• When playing DVD-RW in VR mode: If you
connected to an AV amplifier (receiver) using the
DIGITAL OUT (COAXIAL or OPTICAL) jack
and want to switch between the sound tracks, set
“DOLBY DIGITAL” to “D-PCM” in “AUDIO
SETUP.”
Checking the audio signal
format
You can check the audio signal format by
pressing
(audio) repeatedly during
playback. The format of the current audio
signal (Dolby Digital, DTS, PCM, etc.)
appears as shown below.
◆When playing a DVD VIDEO
Example:
Dolby Digital 5.1 ch
Audio signals recorded in a disc contain the
sound elements (channels) shown below.
Each channel is output from a separate
speaker.
• Front (L)
• Front (R)
• Centre
• Rear (L)
• Rear (R)
• Rear (Monaural): This signal can be either
the Dolby Surround Sound processed
signals or the Dolby Digital sound’s
monaural rear audio signals.
• LFE (Low Frequency Effect) signal
Notes
• If “DTS” in “AUDIO SETUP” is set to “OFF,”
the DTS track selection option will not appear on
the screen even if the disc contains DTS tracks
(page 69).
• MPEG audio signals with more than two channels
will appear as shown above (3/2.1, 2/1), but only
the Front (L) and Front (R) signals will be output
from your two front speakers.
Rear (L/R)
1:ENGLISH DOLBY DIGITAL 3 / 2 .1
Front (L/R)
+ Centre
LFE (Low Frequency
Effect)
Example:
Dolby Digital 3 ch
2:SPANISH DOLBY DIGITAL 2 / 1
Front (L/R)
Rear
(Monaural)
◆When playing a DivX video file on a DATA
CD or a DATA DVD
Example:
MP3 audio
1: MP3 128k
Bit rate
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
42
To cancel the setting
TV Virtual Surround
Settings (TVS)
SUR
◆TVS DYNAMIC THEATER
Creates one set of LARGE virtual rear
speakers and virtual subwoofer from the
sound of the front speakers (L, R) without
using actual rear speakers and subwoofer
(shown below).
This mode is effective when the distance
between the front L and R speakers is short,
such as with built-in speakers on a stereo TV.
TV
Sub
woofer
◆TVS DYNAMIC
Creates one set of virtual rear speakers from
the sound of the front speakers (L, R) without
using actual rear speakers (shown below).
This mode is effective when the distance
between the front L and R speakers is short,
such as with built-in speakers on a stereo TV.
Sound Adjustments
When you connect a stereo TV or 2 front
speakers, TVS (TV Virtual Surround) lets
you enjoy surround sound effects by using
sound imaging to create virtual rear speakers
from the sound of the front speakers (L: left,
R: right) without using actual rear speakers.
TVS was developed by Sony to produce
surround sound for home use using just a
stereo TV.
If the player is set up to output the signal from
the DIGITAL OUT (OPTICAL or
COAXIAL) jack, the surround effect will
only be heard when “DOLBY DIGITAL” is
set to “D-PCM” and “MPEG” is set to
“PCM” in “AUDIO SETUP” (page 68).
Select “OFF” in step 2.
TV
1 Press SUR during playback.
The following display appears.
TVS DYNAMIC THEATER
◆TVS WIDE
Creates five sets of virtual rear speakers from
the sound of the front speakers (L, R) without
using actual rear speakers (shown below).
This mode is effective when the distance
between the front L and R speakers is short,
such as with built-in speakers on a stereo TV.
TV
2 Press SUR repeatedly to select
one of the TVS sounds.
See the explanations given for each item
in the following section.
• TVS DYNAMIC THEATER
• TVS DYNAMIC
• TVS WIDE
• TVS NIGHT
• TVS STANDARD
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
43
◆TVS NIGHT
Large sounds, such as explosions, are
suppressed, but quieter sounds are
unaffected. This feature is useful when you
want to hear the dialogue and enjoy the
surround sound effects of “TVS WIDE” at
low volume.
◆TVS STANDARD
Creates three sets of virtual rear speakers
from the sound of the front speakers (L, R)
without using actual rear speakers (shown
below). Use this setting when you want to use
TVS with 2 separate speakers.
L
R
L: Front speaker (left)
R: Front speaker (right)
: Virtual speaker
Notes
• When the playing signal does not contain a signal
for the rear speakers, you cannot hear the
surround effects.
• When you select one of the TVS modes, turn off
the surround setting of the connected TV or
amplifier (receiver).
• Make sure that your listening position is between
and at an equal distance from your speakers, and
that the speakers are located in similar
surroundings.
• Not all discs will respond to the “TVS NIGHT”
function in the same way.
• The TVS effects do not work when using the Fast
Play or Slow Play functions, even though you can
change the TVS modes.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
44
Enjoying Movies
Displaying the Subtitles
Changing the Angles
If various angles (multi-angles) for a scene
are recorded on the DVD VIDEO, “
”
appears in the front panel display. This means
that you can change the viewing angle.
If subtitles are recorded on the discs, you can
change the subtitles or turn them on and off
whenever you want while playing the disc.
(subtitle) during
playback.
1 Press
(angle) during playback.
Enjoying Movies
1 Press
The following display appears.
The number of the angle appears on the
display.
1:ENGLISH
2
2 Press
2 Press
(angle) repeatedly to
select an angle number.
The scene changes to the selected angle.
Note
Depending on the DVD VIDEO, you may not be
able to change the angles even if multi-angles are
recorded on the DVD VIDEO.
(subtitle) repeatedly to
select a setting.
◆ When playing a DVD VIDEO
Select the language.
Depending on the DVD VIDEO, the
choice of language varies.
When 4 digits are displayed, they
indicate a language code. See “Language
Code List” on page 76 to see which
language the code represents.
◆ When playing a DVD-RW
Select “ON.”
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
45
◆ When playing a DATA CD (DivX
video), or DATA DVD (DivX video)
Select the displayed language. If “OFF”
appears, the player does not support the
subtitle signal format contained in the
disc.
Adjusting the Playback
Picture (CUSTOM PICTURE MODE)
To turn off the subtitles
Select “OFF” in step 2.
Notes
• Depending on the DVD VIDEO, you may not be
able to change the subtitles even if multilingual
subtitles are recorded on it. You also may not be
able to turn them off.
• You can change the subtitles if the DivX video
file has an “.AVI” or “.DIVX” extension and
contains subtitle information within the same file.
• While playing a disc with subtitles, the subtitle
may disappear when you press FAST PLAY or
SLOW PLAY button.
You can adjust the video signal of the DVD,
VIDEO CD, DATA CD/DATA DVD in
JPEG format, or DATA CD/DATA DVD
containing DivX video files from the player
to obtain the picture quality you want. Choose
the setting that best suits the programme you
are watching. When you select “MEMORY,”
you can make further adjustments to each
element of the picture (colour, brightness,
etc.).
ENTER
RETURN
DISPLAY
1 Press DISPLAY during playback.
(When playing a DATA CD/DATA
DVD in JPEG format, press twice)
The Control Menu appears.
2 Press X/x to select
(CUSTOM PICTURE MODE), then
press ENTER.
The options for “CUSTOM PICTURE
MODE” appear.
12(27)
18(34)
T
1:32:55
STANDARD
STANDARD
DYNAMIC 1
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
46
DVD VIDEO
3 Press X/x to select the setting you
want.
You can adjust each element of the picture
individually.
• PICTURE: changes the contrast
• BRIGHTNESS: changes the overall
brightness
• COLOR: makes the colours deeper or
lighter
• HUE: changes the colour balance
1
The “PICTURE”
adjustment bar appears.
8(3 )
C
4 Press ENTER.
The selected setting takes effect.
In step 3 of “Adjusting the Playback
Picture,” select “MEMORY” and press
ENTER.
01:32:55
PICTURE
2
Select :
0
ENTER
Cancel : RETURN
Press C/c to adjust the picture
contrast.
Enjoying Movies
The default setting is underlined.
• STANDARD: displays a standard
picture.
• DYNAMIC 1: produces a bold
dynamic picture by increasing the
picture contrast and the colour
intensity.
• DYNAMIC 2: produces a more
dynamic picture than DYNAMIC 1 by
further increasing the picture contrast
and colour intensity.
• CINEMA 1: enhances details in dark
areas by increasing the black level.
• CINEMA 2: white colours become
brighter and black colours become
richer, and the colour contrast is
increased.
• MEMORY: adjusts the picture in
greater detail.
Adjusting the picture items in
“MEMORY”
To go the next or previous picture item
without saving the current setting, press
X/x.
z Hint
When you watch a movie, “CINEMA 1” or
“CINEMA 2” is recommended.
3
Press ENTER.
The adjustment is saved, and
“BRIGHTNESS” adjustment bar
appears.
4
Repeat step 2 and 3 to adjust
“BRIGHTNESS,” “COLOR,” and
“HUE.”
To turn off the display
Press O RETURN , or DISPLAY.
Note
The “BRIGHTNESS” setting is not effective if you
connect the player via the LINE OUT (VIDEO) or
S VIDEO OUT jack and select “PROGRESSIVE
AUTO” or “PROGRESSIVE VIDEO” by using the
PROGRESSIVE button on the front panel.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
47
Sharpening the Pictures
To cancel the “SHARPNESS” setting
Select “OFF” in step 3.
(SHARPNESS)
Note
You can enhance the outlines of images to
produce a sharper picture.
This setting is not effective if you connect the player
via the LINE OUT (VIDEO), S VIDEO OUT, or
LINE (RGB)-TV jack, and select “PROGRESSIVE
AUTO” or “PROGRESSIVE VIDEO” by using the
PROGRESSIVE button on the front panel.
ENTER
DISPLAY
1 Press DISPLAY during playback
(when playing a DATA CD/DATA
DVD, press twice).
The Control Menu appears.
2 Press X/x to select
(SHARPNESS), then press ENTER.
The options for “SHARPNESS” appear.
12(27)
18(34)
T
1:32:55
DVD VIDEO
OFF
1
2
OFF
3 Press X/x to select a level.
• 1: enhances the outline.
• 2: enhances the outline more than 1.
4 Press ENTER.
The selected setting takes effect.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
48
Enjoying MP3 Audio and JPEG
Images
About MP3 Audio Tracks
and JPEG Image Files
MP3 is audio compression technology that
satisfies the ISO/IEC MPEG regulations.
JPEG is image compression technology.
You can play DATA CDs/DATA DVD that
contain MP3 audio tracks or JPEG image
files.
DATA CDs/DATA DVDs that the
player can play
Notes
• The player will play any data with the extension
“.MP3,” “.JPG,” or “.JPEG,” even if they are not
in MP3 or JPEG format. Playing these data may
generate a loud noise which could damage your
speaker system.
• The player does not conform to audio tracks in
mp3PRO format.
• Some JPEG files cannot be played.
• You cannot play MP3 audio tracks/JPEG image
files in DATA CDs/DATA DVDs that contain
DivX video files.
About playback order of albums,
tracks, and files
Albums play in the following order:
◆Structure of disc contents
Tree 1
Tree 2
Tree 3
Tree 4
Tree 5
ROOT
Enjoying MP3 Audio and JPEG Images
You can play back DATA CDs (CD-ROMs/
CD-Rs/CD-RWs) or DATA DVDs (DVDROMs/DVD+RWs/DVD+Rs/DVD-RWs/
DVD-Rs) recorded in MP3 (MPEG-1 Audio
Layer III) and JPEG format. However, the
discs must be recorded according to ISO9660
Level 1/ Level 2 or Joliet format and DATA
DVDs of Universal Disk Format (UDF) for
the player to recognize the tracks (or files).
Refer to the instructions supplied with the
CD-R/CD-RW drives and the recording
software (not supplied) for details on the
recording format.
Note
The player may not be able to play some DATA
CDs/DATA DVDs created in the Packet Write
format.
MP3 audio track or JPEG image
file that the player can play
The player can play the following tracks and
files:
– MP3 audio tracks with the extension
“.MP3.”
– JPEG image files with the extension
“.JPEG” or “.JPG.”
– JPEG image files that conform to the DCF*
image file format.
Album
Track (MP3 audio) or
file (JPEG image)
* “Design rule for Camera File system”: Image
standards for digital cameras regulated by JEITA
(Japan Electronics and Information Technology
Industries Association).
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
49
When you insert a DATA CD/DATA DVD
and press H, the numbered tracks (or files)
are played sequentially, from 1 through 7.
Any sub-albums/tracks (or files) contained
within a currently selected album take
priority over the next album in the same tree.
(Example: C contains D so 4 is played
before 5.)
When you press MENU and the list of album
names appears (page 51), the album names
are arranged in the following order:
A t B t C t D t F t G. Albums
that do not contain tracks (or files) (such as
album E) do not appear in the list.
z Hints
• If you add numbers (01, 02, 03, etc.) to the front
of the track/file names when you store the tracks
(or files) in a disc, the tracks and files will be
played in that order.
• Since a disc with many trees takes longer to start
playback, it is recommended that you create
albums with no more than two trees.
Playing MP3 Audio
Tracks or JPEG Image
Files
You can play MP3 audio tracks and JPEG
image files on DATA CDs (CD-ROMs/CDRs/CD-RWs) or DATA DVDs (DVD-ROMs/
DVD+RWs/DVD+Rs/DVD-RWs/DVD-Rs).
CLEAR
PICTURE
NAVI
MENU
ENTER
RETURN
ZOOM
Notes
• Depending on the software you use to create the
DATA CD/DATA DVD, the playback order may
differ from the above illustration.
• The playback order above may not be applicable
if there are more than 200 albums and 300 tracks/
files in each album.
• The player can recognize up to 200 albums (the
player will count just albums, including albums
that do not contain MP3 audio tracks and JPEG
image files). The player will not play any albums
beyond the 200th album.
• Proceeding to the next or another album may take
some time.
z Hint
You can view the disc information while playing
MP3 audio tracks (page 37).
Notes
• DATA CDs recorded in KODAK Picture CD
format automatically start playing when inserted.
• If no MP3 audio track or JPEG image file is
recorded on the DATA CD/DATA DVD, “No
audio data” or “No image data” appears on the
screen.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
50
Selecting an album
Selecting an MP3 audio track
1
1
Press MENU.
The list of albums on the disc appears.
When an album is being played, its title is
shaded.
After step 2 of “Selecting an album,”
press ENTER.
The list of tracks in the album appears.
MY FAVOURITE SONG
1(256)
3( 30)
WALTZ FOR DEBBY
MY ROMANCE
MILES TONES
MY FUNNY VALENTINE
AUTUM LEAVES
ALL BLUES
S O M E D A Y M Y P R I N C E W ...
ROCK BEST HIT
KARAOKE
MY FAVOURITE SONG
R&B
JAZZ
CLASSIC
SALSA OF CUBA
BOSSA NOVA
2
3
2
Press X/x to select the album you
want to play.
Press X/x to select a track, and press
ENTER.
Playback starts from the selected track.
Press H.
To stop playback
Press x.
To go to the next or previous page
Press c or C.
To return to the previous display
To stop playback
Press x.
To go to the next or previous page
Press c or C.
To turn on or off the display
Press MENU repeatedly.
z Hint
Of the selected album, you can select to play only
the MP3 audio tracks, JPEG image files, or both, by
setting “MODE (MP3, JPEG)” (page 53).
Press O RETURN.
To go to the next or previous MP3 audio
track
Press > or . during playback. You can
select the first track of the next album by
pressing > during playback of the last
track of the current album.
Note that you cannot return to the previous
album by using ., and that you need to
select the previous album from the album list.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
Enjoying MP3 Audio and JPEG Images
Playback starts from the selected album.
To select MP3 audio tracks, see
“Selecting an MP3 audio track”
(page 51).
To select JPEG image files, see
“Selecting a JPEG image file” (page 52).
51
Selecting a JPEG image file
1
After step 2 of “Selecting an album,”
press PICTURE NAVI.
The image files in the album appear in 16
subscreens. A scroll box is displayed on
the right.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
To display the additional image, select
the bottom images and press x. To return
to the previous image, select the top
images and press X.
2
Press C/X/x/c to select the image you
want to view, and press ENTER.
The selected image appears.
Example
To rotate a JPEG image
Press X/x while viewing the image. Each
time you press X, the image rotates
counterclockwise by 90 degrees.
To return to normal view, press CLEAR.
Note that the view also returns to normal if
you press C/c to go to the next or previous
image.
Example: when X is pressed once.
Rotating direction
To magnify a JPEG image (ZOOM)
Press ZOOM while viewing the image. You
can enlarge the image up to four times the
original size, and scroll using C/X/x/c.
To return to normal view, press CLEAR.
◆When pressed once (x2)
The image enlarges twice the original size.
◆When pressed twice (x4)
The image enlarges four times the original
size.
To stop viewing the JPEG image
Press x.
To go to the next or previous JPEG image
file
Press C or c during playback. You can select
the first file of the next album by pressing c
during playback of the last file of the current
album.
Note that you cannot return to the previous
album by using C, and that you need to select
the previous album from the album list.
z Hints
• While viewing JPEG image files, you can set
options such as “INTERVAL” (page 54),
“EFFECT” (page 55), and “SHARPNESS”
(page 48).
• You can view JPEG images files without MP3
audio by setting “MODE (MP3, JPEG)” to
“IMAGE (JPEG)” (page 53).
• The date the picture was taken is displayed beside
“DATE” in the Control Menu (page 11). Note that
no date may appear depending on the digital
camera.
Note
PICTURE NAVI does not work if “AUDIO (MP3)”
is selected in “MODE (MP3, JPEG)” (page 53).
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
52
Enjoying JPEG Images as
a Slide Show
Viewing a slide show with sound
(MODE (MP3, JPEG))
You can play JPEG image files on a DATA
CD or DATA DVD successively as a slide
show.
1
When JPEG image files and MP3 audio
tracks are placed in the same album, you can
enjoy a slide show with sound.
Press DISPLAY during stop mode.
The Control Menu appears.
2
Press X/x to select
(MODE
(MP3, JPEG)), and press ENTER.
The options for “MODE (MP3, JPEG)”
appear.
12(27)
18(34)
T
32:55
AUTO
AUTO
AUDIO (MP3)
IMAGE (JPEG)
MENU
ENTER
DISPLAY
• AUTO: plays both the JPEG image files
and MP3 audio tracks in the same
album as a slide show.
• AUDIO (MP3): plays only MP3 audio
tracks continuously.
• IMAGE (JPEG): plays only JPEG
image files continuously.
The list of albums on the DATA CD/
DATA DVD appears.
3( 30)
ROCK BEST HIT
KARAOKE
MY FAVOURITE SONG
R&B
JAZZ
CLASSIC
SALSA OF CUBA
BOSSA NOVA
4
3( 30)
ROCK BEST HIT
KARAOKE
MY FAVOURITE SONG
R&B
JAZZ
CLASSIC
SALSA OF CUBA
BOSSA NOVA
The JPEG images in the selected album
start playing as a slide show.
5
Press X/x to select the album that
contains both the MP3 audio tracks
and JPEG images you want to play.
6
Press H.
Press x.
Notes
• The slide show stops when X/x or ZOOM is
pressed.To resume the slide show, press H.
• This function does not work if “MODE (MP3,
JPEG)” is set to “AUDIO (MP3)” (page 53).
Press MENU.
The list of albums on the DATA CD/
DATA DVD appears.
2 Press X/x to select an album.
3 Press H.
To stop playback
Press X/x to select “AUTO” (default),
and press ENTER.
Enjoying MP3 Audio and JPEG Images
1 Press MENU.
3
DATA CD MP3
A slide show starts with sound.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
53
z Hints
• To repeat both MP3 audio tracks and JPEG image
files in a single album, repeat the same MP3 audio
track or album when “MODE (MP3, JPEG)” is set
to “AUTO.” See “Playing repeatedly (Repeat
Play)” (page 31) to repeat the track or album.
• The player recognizes a maximum of 200 albums
regardless of the selected mode. Of each album,
the player recognizes up to 300 MP3 audio tracks
and 300 JPEG image files when “AUTO” is
selected, 600 MP3 audio tracks when “AUDIO
(MP3)” is selected, 600 JPEG image files when
“IMAGE (JPEG)” is selected.
Setting the pace for a slide show
(INTERVAL)
You can set the time the slides are displayed
on the screen.
1
The Control Menu appears.
2
Notes
• This function does not work if the MP3 audio
tracks and JPEG image files are not placed in the
same album.
• If playing time of JPEG image or MP3 audio is
longer than the other, the longer one continues
without sound or image.
• If you play large MP3 track data and JPEG image
data at the same time, the sound may skip. It is
recommended that you set the MP3 bit rate to 128
kbps or lower when creating the file. If the sound
still skips, then reduce the size of the JPEG file.
Press DISPLAY twice while viewing a
JPEG image or when the player is in
stop mode.
Press X/x to select
(INTERVAL), then press ENTER.
The options for “INTERVAL” appear.
3 ( 12)
4)
1(
29/10/2005
NORMAL
NORMAL
FAST
SLOW 1
SLOW 2
3
DATA CD JPEG
INTERVAL
Press X/x to select a setting.
The default setting is underlined.
• NORMAL: sets the duration to between
6 to 9 seconds.
• FAST: sets a duration shorter than
NORMAL.
• SLOW 1: sets a duration longer than
NORMAL.
• SLOW 2: sets a duration longer than
SLOW 1.
4
Press ENTER.
Note
Some JPEG files, especially progressive JPEG files
or JPEG files of 3,000,000 pixels or more, may take
longer to display than others, which may make the
duration seem longer than the setting you selected.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
54
Selecting the slides’ appearance
(EFFECT)
You can select the way the slides are
displayed during a slide show.
1
Press DISPLAY twice while viewing a
JPEG image or when the player is in
stop mode.
2
Press X/x to select
then press ENTER.
(EFFECT),
The options for “EFFECT” appear.
3 ( 12)
4)
1(
23/10/2005
DATA CD JPEG
MODE 1
MODE 1
MODE 2
MODE 3
MODE 4
MODE 5
OFF
EFFECT
Press X/x to select a setting.
The default setting is underlined.
• MODE 1: the image sweeps in from top
to bottom.
• MODE 2: the image sweeps in from left
to right.
• MODE 3: the image stretches out from
the centre of the screen.
• MODE 4: the images randomly cycle
through the effects.
• MODE 5: the next image slides over the
previous image.
• OFF: turns off this function.
4
Enjoying MP3 Audio and JPEG Images
3
Press ENTER.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
55
Enjoying DivX® Videos
About DivX Video Files
DivX® is a video file compression
technology, developed by DivXNetworks,
Inc. This product is an official DivX®
Certified product.
You can play DATA CDs and DATA DVDs
that contain DivX video files.
DATA CDs and DATA DVDs that
the player can play
Playback of DATA CDs (CD-ROMs/CD-Rs/
CD-RWs) and DATA DVDs (DVD-ROMs/
DVD+RWs/DVD+Rs/DVD-RWs/DVD-Rs)
on this player is subject to certain conditions:
– With DATA CDs/DATA DVDs that
contain DivX video files in addition to MP3
audio tracks or JPEG image files, the player
plays only the DivX video files.
However, this player only plays DATA CDs
whose logical format is ISO 9660 Level 1/
Level 2 or Joliet, and DATA DVDs of
Universal Disk Format (UDF).
Refer to the instructions supplied with the
disc drives and the recording software (not
supplied) for details on the recording format.
DivX video files that the player
can play
The player can play data that is recorded in
DivX format, and which has the extension
“.AVI” or “.DIVX.” The player will not play
files with the extension “.AVI” or “.DIVX” if
they do not contain a DivX video.
z Hint
For details about playable MP3 audio tracks or
JPEG image files on DATA CDs/DATA DVDs, see
“DATA CDs/DATA DVDs that the player can
play” (page 49).
Notes
• The player may not play a DivX video file when
the file has been combined from two or more
DivX video files.
• The player cannot play a DivX video file of size
more than 720 (width) × 576 (height)/2 GB.
• Depending on the DivX video file, the picture
may be unclear or the sound may skip.
• The player cannot play some DivX video files that
are longer than 3 hours.
About playback order of data on DATA CDs
or DATA DVDs
See “About playback order of albums, tracks,
and files” (page 49). Note that the playback
order may not be applicable, depending on
the software used for creating the DivX video
file, or if there are more than 200 albums and
600 DivX video files in each album.
Note
The player may not be able to play some DATA
CDs/DATA DVDs created in the Packet Write
format.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
56
Playing DivX Video Files
Selecting an album
1
Press MENU.
A list of albums on the disc appears. Only
albums that contain DivX video files are
listed.
You can play DivX video files on DATA CDs
(CD-ROMs/CD-Rs/CD-RWs) and DATA
DVDs (DVD-ROMs/DVD+RWs/DVD+Rs/
DVD-RWs/DVD-Rs).
3( 3)
SUMMER 2003
NEW YEAR'S DAY
MY FAVOURITES
MENU
RETURN
ENTER
DISPLAY
2
Press X/x to select the album you
want to play.
3
Press H.
Playback starts from the selected album.
To select DivX video files, see “Selecting
a DivX video file” (page 58).
To stop playback
Press x.
Notes
• If there are no DivX video files recorded on the
DATA CD/DATA DVD, a message appears to
indicate that the disc is not playable.
• Depending on the DivX video file, the picture
may pause or be unclear. In which case, it is
recommended that you create the file at a lower
bit rate. If the sound is still noisy, MP3 is the
recommended audio format. Note, however, this
player does not conform to WMA (Windows
Media Audio) format.
• Because of the compression technology used for
DivX video files, it may take some time after you
press H (play) for the picture to appear.
• Depending on the DivX video file, the sound may
not match the pictures on the screen.
To go to the next or previous page
Press C or c.
To turn the display on or off
Press MENU repeatedly.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
Enjoying DivX® Videos
z Hint
You can view the disc information while playing a
DivX video file (page 37).
57
Selecting a DivX video file
1
After step 2 of “Selecting an album,”
press ENTER.
The list of files in the album appears.
MY FAVOURITES
1(2 )
HAWAII 2004
VENUS
2
Press X/x to select a file, and press
ENTER.
The selected file starts playing.
To stop playback
Press x.
To go to the next or previous page
Press C or c.
To return to the previous display
Press O RETURN.
To go to the next or previous DivX video
file without turning on the above file list
You can select the next or previous DivX
video file in the same album by pressing >
or ..
You can also select the first file of the next
album by pressing > during playback of
the last file of the current album. Note that
you cannot return to the previous album by
using .. To return to the previous album,
select it from the album list.
z Hint
If the number of viewing times is preset, you can
play the DivX video files as many times as the
preset number. The following occurrences are
counted:
– when the player is turned off. This includes when
the player is automatically turned off by the Auto
Power Off function. Press X instead of x when
you want to stop viewing
– when the disc tray is opened.
– when another file is played.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
58
3
Using Various Additional
Functions
Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
The options for “PARENTAL
CONTROL” appear.
Locking Discs (CUSTOM
12(27)
18(34)
T
1:32:55
PARENTAL CONTROL, PARENTAL
STOP
DVD VIDEO
CONTROL)
You can set two kinds of playback restrictions
for a disc.
• Custom Parental Control
You can set playback restrictions so that the
player will not play inappropriate discs.
• Parental Control
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users. Scenes may be
blocked or replaced with different scenes.
The same password is used for both Parental
Control and Custom Parental Control.
ON
PLAYER
PASSWORD
OFF
4
Press X/x to select “ON t,” then
press ENTER.
◆ If you have not entered a password
The display for registering a new
password appears.
PARENTAL CONTROL
Enter a new 4-digit password,
then press ENTER .
Number
buttons
ENTER
DISPLAY
◆ When you have already registered a
password
The display for entering the password
appears.
5
Custom Parental Control
You can set the same Custom Parental
Control password for up to 40 discs. When
you set the 41st-disc, the first disc is
cancelled.
1
Insert the disc you want to lock.
If the disc is playing, press x to stop
playback.
2
Press DISPLAY while the player is in
stop mode.
The Control Menu appears.
Enter or re-enter your 4-digit password
using the number buttons, then press
ENTER.
Using Various Additional Functions
Enter a 4-digit password using the
number buttons, then press ENTER.
The display for confirming the password
appears.
“Custom parental control is set.” appears
and then the screen returns to the Control
Menu.
To turn off the Custom Parental Control
function
1
Follow steps 1 to 3 of “Custom Parental
Control.”
2
Press X/x to select “OFF t,” then press
ENTER.
3
Enter your 4-digit password using the
number buttons, then press ENTER.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
59
To play a disc for which Custom Parental
Control is set
1
3
Press X/x to select “PLAYER t,”
then press ENTER.
◆ If you have not entered a password
The display for registering a new
password appears.
Insert the disc for which Custom Parental
Control is set.
The “CUSTOM PARENTAL
CONTROL” display appears.
PARENTAL CONTROL
CUSTOM PARENTAL CONTROL
Enter a new 4-digit password,
then press ENTER .
Custom parental control is already
set. To play, enter your password
and press ENTER .
2
Enter a 4-digit password using the
number buttons, then press ENTER.
The display for confirming the password
appears.
Enter your 4-digit password using the
number buttons, then press ENTER.
The player is ready for playback.
z Hint
If you forget your password, enter the 6-digit
number “199703” using the number buttons when
the “CUSTOM PARENTAL CONTROL” display
asks you for your password, then press ENTER.
The display will ask you to enter a new 4-digit
password.
◆ When you have already registered a
password
The display for entering the password
appears.
4
The display for setting the playback
limitation level appears.
Parental Control (limited
playback)
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users. The
“PARENTAL CONTROL” function allows
you to set a playback limitation level.
1
Press DISPLAY while the player is in
stop mode.
The Control Menu appears.
2
PARENTAL CONTROL
LEVEL:
STANDARD:
5
Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
ON
PLAYER
PASSWORD
OFF
OFF
USA
Press X/x to select “STANDARD,”
then press ENTER.
The selection items for “STANDARD”
are displayed.
The options for “PARENTAL
CONTROL” appear.
12(27)
18(34)
T
1:32:55
Enter or re-enter your 4-digit password
using the number buttons, then press
ENTER.
PARENTAL CONTROL
LEVEL:
STANDARD:
STOP
DVD VIDEO
6
OFF
USA
USA
OTHERS
Press X/x to select a geographic area
as the playback limitation level, then
press ENTER.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
60
The area is selected.
When you select “OTHERS t,” select
and enter a standard code in the table on
page 76 using the number buttons.
7
Press X/x to select “LEVEL,” then
press ENTER.
The selection items for “LEVEL” are
displayed.
Changing the password
PARENTAL CONTROL
LEVEL:
STANDARD:
OFF
OFF
8:
7:
6:
5:
8
Notes
• When you play discs which do not have the
Parental Control function, playback cannot be
limited on this player.
• Depending on the disc, you may be asked to
change the parental control level while playing
the disc. In this case, enter your password, then
change the level. If the Resume Play mode is
cancelled, the level returns to the previous level.
1
NC17
R
The Control Menu appears.
2
Select the level you want using X/x,
then press ENTER.
3
4:
PG13
USA
To turn off the Parental Control function
Set “LEVEL” to “OFF” in step 8.
To play a disc for which Parental Control is
set
1
Insert the disc and press H.
The display for entering your password
appears.
2
Enter your 4-digit password using the
number buttons, then press ENTER.
The player starts playback.
Press X/x to select “PASSWORD
t,” then press ENTER.
The display for entering the password
appears.
4
Enter your 4-digit password using the
number buttons, then press ENTER.
5
Enter a new 4-digit password using the
number buttons, then press ENTER.
6
To confirm your password, re-enter it
using the number buttons, then press
ENTER.
If you make a mistake entering your
password
Press C before you press ENTER and input
the correct number.
Using Various Additional Functions
The lower the value, the stricter the
limitation.
Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
The options for “PARENTAL
CONTROL” appear.
Parental Control setting is complete.
PARENTAL CONTROL
LEVEL:
STANDARD:
Press DISPLAY while the player is in
stop mode.
z Hint
If you forget your password, remove the disc and
repeat steps 1 to 3 of “Parental Control (limited
playback).” When you are asked to enter your
password, enter “199703” using the number
buttons, then press ENTER. The display will ask
you to enter a new 4-digit password. After you enter
a new 4-digit password, replace the disc in the
player and press H. When the display for entering
your password appears, enter your new password.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
61
Controlling Your TV With
the Supplied Remote
You can control the sound level, input source,
and power switch of your Sony TV with the
supplied remote.
TV
Number
buttons
Controlling other TVs with the
remote
You can control the sound level, input source,
and power switch of non-Sony TVs as well.
If your TV is listed in the table below, set the
appropriate manufacturer’s code.
1
While holding down TV [/1, press the
number buttons to select your TV’s
manufacturer’s code (see the table
below).
2
Release TV [/1.
2 +/–
t
Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the
one that works with your TV.
Manufacturer
You can control your TV using the buttons
below.
Code number
Sony
01 (default)
Aiwa
01 (default)
Grundig
11
Hitachi
24
By pressing
You can
JVC
33
TV [/1
Turn the TV on or off
LG
06
2 (volume) +/– Adjust the volume of the TV
Loewe
06
t (TV/video)
Panasonic
17, 49
Philips
06, 08
Samsung
06, 71
Sanyo
25
Sharp
29
Switch the TV’s input source
between the TV and other
input sources
Note
Depending on the connected unit, you may not be
able to control your TV using all or some of the
buttons on the supplied remote.
Thomson
43
Toshiba
38
Notes
• When you replace the batteries of the remote, the
code number you have set may be reset to the
default setting. Set the appropriate code number
again.
• Depending on the unit being connected, you may
not be able to control your TV using all or some
of the buttons on the supplied remote.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
62
3 Press X/x to select “CUSTOM,”
Settings and Adjustments
Using the Setup Display
By using the Setup Display, you can make
various adjustments to items such as picture
and sound. You can also set a language for the
subtitles and the Setup Display, among other
things.
For details on each Setup Display item, see
pages from 64 to 69.
Note
Playback settings stored in the disc take priority
over the Setup Display settings and not all of the
functions described may work.
then press ENTER.
The Setup Display appears.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
4 Press X/x to select the setup item
from the displayed list:
“LANGUAGE SETUP,” “SCREEN
SETUP,” “CUSTOM SETUP,” or
“AUDIO SETUP.” Then press
ENTER.
The Setup item is selected.
Example: “SCREEN SETUP”
Selected item
ENTER
DISPLAY
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
4:3 OUTPUT:
16:9
ON
JACKET PICTURE
VIDEO
FULL
1 Press DISPLAY when the player is 5 Press X/x to select an item, then
in stop mode.
press ENTER.
The Control Menu appears.
The options for the selected item appear.
Example: “TV TYPE”
2 Press X/x to select
(SETUP), then press ENTER.
The options for “SETUP” appear.
( 47 )
STOP
DVD VIDEO
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
4:3 OUTPUT:
Settings and Adjustments
Setup items
16:9
16:9
4:3 LETTER BOX
4:3 PAN SCAN
FULL
Options
QUICK
CUSTOM
RESET
QUICK
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
63
6 Press X/x to select a setting, then
press ENTER.
The setting is selected and setup is
complete.
Example: “4:3 PAN SCAN”
Setting the Display or
Sound Track Language
(LANGUAGE SETUP)
Selected setting
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
4:3 OUTPUT:
4:3 PAN SCAN
ON
JACKET PICTURE
VIDEO
FULL
“LANGUAGE SETUP” allows you to set
various languages for the on-screen display or
sound track.
Select “LANGUAGE SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 63).
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
To enter the Quick Setup mode
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
Select “QUICK” in step 3. Follow from step
5 of the Quick Setup explanation to make
basic adjustments (page 21).
To reset all of the “SETUP” settings
◆ OSD (On-Screen Display)
1
Select “RESET” in step 3 and press
ENTER.
Switches the display language on the screen.
2
Select “YES” using X/x.
You can also quit the process and return
to the Control Menu by selecting “NO”
here.
3
Press ENTER.
All the settings explained on pages 64 to
67 return to the default settings. Do not
press [/1 while resetting the player,
which takes a few seconds to complete.
◆ MENU (DVD VIDEO only)
You can select the desired language for the
disc’s menu.
◆ AUDIO (DVD VIDEO only)
Switches the language of the sound track.
When you select “ORIGINAL,” the language
given priority in the disc is selected.
◆ SUBTITLE (DVD VIDEO only)
Switches the language of the subtitle recorded
on the DVD VIDEO.
When you select “AUDIO FOLLOW,” the
language for the subtitles changes according
to the language you selected for the sound
track.
z Hint
If you select “OTHERS t” in “MENU,”
“SUBTITLE,” or “AUDIO,” select and enter a
language code from “Language Code List” on
page 76 using the number buttons.
Note
If you select a language in “MENU,”
“SUBTITLE,” or “AUDIO” that is not recorded on
a DVD VIDEO, one of the recorded languages will
be automatically selected.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
64
Settings for the Display
(SCREEN SETUP)
Choose settings according to the TV to be
connected.
Select “SCREEN SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 63).
The default settings are underlined.
SCREEN SETUP
TV TYPE:
SCREEN SAVER:
BACKGROUND:
LINE:
4:3 OUTPUT:
16:9
ON
JACKET PICTURE
VIDEO
FULL
Note
Depending on the DVD, “4:3 LETTER BOX” may
be selected automatically instead of “4:3 PAN
SCAN” or vice versa.
◆ SCREEN SAVER
The screen saver image appears when you
leave the player in pause or stop mode for 15
minutes, or when you play a CD or DATA
CD/DATA DVD (MP3 audio) for more than
15 minutes. The screen saver will help
prevent your display device from becoming
damaged (ghosting). Press H to turn off the
screen saver.
ON
Turns on the screen saver.
OFF
Turns off the screen saver.
◆ BACKGROUND
◆ TV TYPE
Selects the aspect ratio of the connected TV
(4:3 standard or wide).
Select this when you connect a
wide-screen TV or a TV with a
wide mode function.
4:3
LETTER
BOX
Select this when you connect a
4:3 screen TV. Displays a wide
picture with bands on the upper
and lower portions of the
screen.
4:3
Select this when you connect a
PAN SCAN 4:3 screen TV. Automatically
displays the wide picture on the
entire screen and cuts off the
portions that do not fit.
16:9
4:3 LETTER BOX
JACKET
PICTURE
The jacket picture (still picture)
appears, but only when the
jacket picture is already
recorded on the disc (CDEXTRA, etc.). If the disc does
not contain a jacket picture, the
“GRAPHICS” picture appears.
GRAPHICS A preset picture stored in the
player appears.
BLUE
The background colour is blue.
BLACK
The background colour is
black.
◆ LINE
Selects video signals output from the LINE
(RGB)-TV jack on the rear panel of the
player.
VIDEO
Outputs video signals.
S VIDEO
Outputs S video signals.
RGB
Outputs RGB signals.
Settings and Adjustments
16:9
Selects the background colour or picture on
the TV screen when the player is in stop mode
or while playing a CD or DATA CD/DATA
DVD (MP3 audio).
Notes
4:3 PAN SCAN
• If your TV does not accept S video or the RGB
signals, no picture will appear on the TV screen,
even if you select “S VIDEO” or “RGB.” Refer to
the instructions supplied with your TV.
• If your TV has only one SCART (EURO AV)
jack, do not select “S VIDEO.”
• When you select “RGB,” you cannot use the
PROGRESSIVE button or the COMPONENT
VIDEO OUT jacks.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
65
◆ 4:3 OUTPUT
This setting is effective only when you set
“TV TYPE” in “SCREEN SETUP” to
“16:9.” Adjust this to watch 4:3 aspect ratio
progressive signals. If you can change the
aspect ratio on your progressive format
(525p/625p) compatible TV, change the
setting on your TV, not the player. This
setting is effective only when
“PROGRESSIVE AUTO” or
“PROGRESSIVE VIDEO” is selected by
using the PROGRESSIVE button on the front
panel.
FULL
Select this when you can
change the aspect ratio on your
TV.
NORMAL
Select this when you cannot
change the aspect ratio on your
TV. Shows a 16:9 aspect ratio
signal with black bands on left
and right sides of the image.
Custom Settings (CUSTOM
SETUP)
Use this to set up playback related and other
settings.
Select “CUSTOM SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 63).
The default settings are underlined.
CUSTOM SETUP
AUTO POWER OFF:
ON
AUTO PLAY:
OFF
DIMMER:
BRIGHT
AUTO
PAUSE MODE:
TRACK SELECTION:
OFF
MULTI-DISC RESUME:
ON
Registration Code
DivX:
◆ AUTO POWER OFF
Switches the Auto Power Off setting on or
off.
ON
The player enters standby mode
when left in stop mode for more
than 30 minutes.
OFF
Switches this function off.
16:9 aspect ratio TV
◆ AUTO PLAY
Switches the Auto Play setting on or off. This
function is useful when the player is
connected to a timer (not supplied).
OFF
Switches this function off.
ON
Automatically starts playback
when the player is turned on by
a timer (not supplied).
◆ DIMMER
Adjusts the lighting of the front panel display.
BRIGHT
Makes the lighting bright.
DARK
Makes the lighting dark.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
66
◆ PAUSE MODE (DVD VIDEO/DVD-RW
only)
Selects the picture in pause mode.
AUTO
FRAME
The picture, including subjects
that move dynamically, is
output with no jitter. Normally
select this position.
The picture, including subjects
that do not move dynamically,
is output in high resolution.
◆ TRACK SELECTION (DVD VIDEO only)
Gives the sound track which contains the
highest number of channels priority when you
play a DVD VIDEO on which multiple audio
formats (PCM, MPEG audio, DTS, or Dolby
Digital format) are recorded.
OFF
No priority given.
AUTO
Priority given.
Settings for the Sound
(AUDIO SETUP)
“AUDIO SETUP” allows you to set the sound
according to the playback and connection
conditions.
Select “AUDIO SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 63).
The default settings are underlined.
AUDIO SETUP
AUDIO ATT:
OFF
AUDIO DRC:
STANDARD
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
ON
D-PCM
DOLBY DIGITAL:
MPEG:
PCM
DTS:
OFF
48kHz/96kHz PCM:
48kHz/16bit
Notes
• When you set the item to “AUTO,” the language
may change. The “TRACK SELECTION” setting
has higher priority than the “AUDIO” settings in
“LANGUAGE SETUP” (page 64).
• If you set “DTS” to “OFF” (page 69), the DTS
sound track is not played even if you set “TRACK
SELECTION” to “AUTO.”
• If PCM, DTS, MPEG audio, and Dolby Digital
sound tracks have the same number of channels,
the player selects PCM, DTS, MPEG, and Dolby
Digital audio sound tracks in this order.
◆ AUDIO ATT (attenuation)
OFF
Normally, select this position.
◆ MULTI-DISC RESUME (DVD VIDEO/
VIDEO CD only)
ON
Select this when the playback sound
from the speakers is distorted.
ON
Stores the resume setting in
memory for up to 6 discs.
OFF
Does not store the resume
setting in memory. Playback
restarts at the resume point only
for the current disc in the player.
Note
If you run Quick Setup; Multi-Disc Resume setting
stored in memory may return to the default setting.
◆ AUDIO DRC (Dynamic Range Control)
(DVD VIDEO/DVD-RW only)
Makes the sound clear when the volume is
turned down when playing a DVD that
conforms to “AUDIO DRC.”
This function affects the output from the
following jacks:
– LINE OUT L/R (AUDIO) jacks
– LINE (RGB)-TV jack
– DIGITAL OUT (OPTICAL or COAXIAL)
jack only when “DOLBY DIGITAL” is set
to “D-PCM” (page 68).
Settings and Adjustments
Switches the Multi-disc Resume setting on or
off. Resume playback can be stored in
memory for up to 6 different DVD VIDEOs/
VIDEO CDs (page 26).
If the playback sound is distorted, set this
item to “ON.” The player reduces the audio
output level.
This function affects the output of the
following jacks:
– LINE OUT L/R (AUDIO) jacks
– LINE (RGB)-TV jack
STANDARD Normally select this position.
◆ DivX
TV MODE
Displays the registration code for this player.
For more information, go to
http://www.divx.com
on the Internet.
Makes low sounds clear even if
you turn the volume down.
WIDE
RANGE
Gives you the feeling of being
at a live performance.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
67
◆ DOWNMIX (DVD VIDEO/DVD-RW only)
Switches the method for mixing down to 2
channels when you play a DVD which has
rear sound elements (channels) or is recorded
in Dolby Digital format. For details on the
rear signal components, see “Checking the
audio signal format” (page 42). This function
affects the output of the following jacks:
– LINE OUT L/R (AUDIO) jacks
– LINE (RGB)-TV jack
– DIGITAL OUT (OPTICAL or COAXIAL)
jack when “DOLBY DIGITAL” is set to
“D-PCM” (page 68).
DOLBY
SURROUND
Normally, select this position.
Multi-channel audio signals are
output to 2 channels for enjoying
surround sounds.
NORMAL
Multi-channel audio signals are
downmixed to 2 channels for use
with your stereo.
Setting the digital output signal
Switches the method of outputting audio
signals when you connect a component such
as an amplifier (receiver) or MD deck with a
digital input jack.
For connection details, see page 19.
Select “DOLBY DIGITAL,” “MPEG,”
“DTS,” and “48kHz/96kHz PCM” after
setting “DIGITAL OUT” to “ON.”
If you connect a component that is
incompatible with the selected audio signal, a
loud noise (or no sound) may be heard from
the speakers, risking damage to your ears or
speakers.
◆ DOLBY DIGITAL (DVD VIDEO/DVD-RW
only)
Selects the type of Dolby Digital signal.
D-PCM
Select this when the player is
connected to an audio
component without a built-in
Dolby Digital decoder. You can
select whether the signals
conform to Dolby Surround
(Pro Logic) or not by making
adjustments to the
“DOWNMIX” item in
“AUDIO SETUP” (page 67).
DOLBY
DIGITAL
Select this when the player is
connected to an audio
component with a built-in
Dolby Digital decoder.
◆ DIGITAL OUT
Selects if audio signals are output via the
DIGITAL OUT (OPTICAL or COAXIAL)
jack.
ON
OFF
Normally select this position. When
you select “ON,” see “Setting the
digital output signal” for further
settings.
The influence of the digital circuit
upon the analog circuit is minimal.
◆ MPEG (DVD VIDEO/DVD-RW only)
Selects the type of MPEG audio signal.
PCM
Select this when the player is
connected to an audio
component without a built-in
MPEG decoder. If you play
MPEG audio sound tracks, the
player outputs stereo signals
via the DIGITAL OUT
(OPTICAL or COAXIAL)
jack.
MPEG
Select this when the player is
connected to an audio
component with a built-in
MPEG decoder.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
68
◆ DTS
Selects whether or not to output DTS signals.
OFF
Select this when the player is
connected to an audio
component without a built-in
DTS decoder.
ON
Select this when the player is
connected to an audio
component with a built-in DTS
decoder.
◆ 48kHz/96kHz PCM (DVD VIDEO only)
Selects the sampling frequency of the audio
signal.
48kHz/16bit The audio signals of DVD
VIDEOs are always converted
to 48kHz/16bit.
96kHz/24bit All types of signals including
96kHz/24bit are output in their
original format. However, if the
signal is encrypted for
copyright protection purposes,
the signal is only output as
48kHz/16bit.
Note
The analogue audio signals from the LINE OUT L/
R (AUDIO) jacks are not affected by this setting
and keep their original sampling frequency level.
Settings and Adjustments
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
69
Additional Information
Troubleshooting
If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
Power
The power is not turned on.
, Check that the mains lead is connected
securely.
Picture
There is no picture/picture noise appears.
, Re-connect the connecting cord securely.
, The connecting cords are damaged.
, Check the connection to your TV (page 15)
and switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
, Set “LINE” in “SCREEN SETUP” to an
item appropriate for your system (page 65).
, The disc is dirty or flawed.
, If the picture output from your player goes
through your VCR to get to your TV or if
you are connected to a combination TV/
VIDEO player, the copy-protection signal
applied to some DVD programmes could
affect picture quality. If you still experience
problems even when you connect your
player directly to your TV, try connecting
your player to your TV’s S VIDEO input
(page 15).
, The disc is recorded in a colour system that
is different from your TV.
, You have selected “PROGRESSIVE
AUTO” or “PROGRESSIVE VIDEO”
using the PROGRESSIVE button on the
front panel (the PROGRESSIVE indicator
lights up) even though your TV cannot
accept the progressive signal. In this case,
select “NORMAL (INTERLACE)” so that
the PROGRESSIVE indicator turns off.
, Even if your TV is compatible with
progressive format 525p/625p signals, the
image may be affected when you set the
player to progressive format. In this case,
select “NORMAL (INTERLACE)” using
the PROGRESSIVE button on the front
panel so that the PROGRESSIVE indicator
turns off and the player is set to normal
(interlace) format.
, If you set “LINE” to “RGB” in “SCREEN
SETUP” (page 21, 65), the player outputs
no component video signals.
The picture does not fill the screen, even
though the aspect ratio is set in “TV TYPE”
under “SCREEN SETUP.”
, The aspect ratio of the disc is fixed on your
DVD.
The picture is black and white.
, Set “LINE” in “SCREEN SETUP” to an
item appropriate for your TV (page 65).
, Depending on the TV, the picture on the
screen becomes black and white when you
play a disc recorded in the NTSC colour
system.
, If you are using a SCART cord, be sure to
use one that is fully wired (21-pins).
Sound
There is no sound.
, Re-connect the connecting cord securely.
, The connecting cord is damaged.
, The player is connected to the wrong input
jack on the amplifier (receiver) (page 19).
, The amplifier (receiver) input is not
correctly set.
, The player is in pause mode or in Slowmotion Play mode.
, The player is in fast forward or fast reverse
mode.
, If the audio signal does not come through
the DIGITAL OUT (OPTICAL or
COAXIAL) jack, check the audio settings
(page 68).
, While playing a Super VCD on which the
audio track 2 is not recorded, no sound will
come out when you select “2:STEREO,”
“2:1/L,” or “2:2/R.”
, When playing multichannel MPEG audio
soundtracks, only the Front (L) and Front
(R) signal will be output from your two
front speakers.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
70
Sound distortion occurs.
, Set “AUDIO ATT” in “AUDIO SETUP” to
“ON” (page 67).
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“AUDIO DRC” in “AUDIO SETUP” to
“TV MODE” (page 67).
, Set “AUDIO ATT” in “AUDIO SETUP” to
“OFF” (page 67).
Operation
The remote does not function.
, The batteries in the remote are weak.
, There are obstacles between the remote and
the player.
, The distance between the remote and the
player is too far.
, The remote is not pointed at the remote
sensor on the player.
The disc does not play.
The MP3 audio track cannot be played
(page 50).
, The DATA CD is not recorded in an MP3
format that conforms to ISO 9660 Level 1/
Level 2 or Joliet.
, The DATA DVD is not recorded in MP3
format that conform to UDF (Universal
Disk Format).
, The MP3 audio track does not have the
extension “.MP3.”
, The data is not formatted in MP3 even
though it has the extension “.MP3.”
, The data is not MPEG-1 Audio Layer III
data.
, The player cannot play audio tracks in
mp3PRO format.
, “MODE (MP3, JPEG)” is set to “IMAGE
(JPEG)” (page 53).
The JPEG image file cannot be played
(page 50).
, The DATA CD is not recorded in a JPEG
format that conforms to ISO 9660 Level 1/
Level 2, or Joliet.
, The DATA DVD is not recorded in JPEG
format that conforms to UDF (Universal
Disk Format).
, The file has an extension other than
“.JPEG” or “.JPG.”
, The image is larger than 3072 (width) ×
2048 (height) in normal mode, or more than
3,300,000 pixels in progressive JPEG.
(Some progressive JPEG files cannot be
displayed even if the file size is within this
specified capacity.)
, The image does not fit the screen (the image
is reduced).
, “MODE (MP3, JPEG)” is set to “AUDIO
(MP3)” (page 53).
, The DATA CD/DATA DVD contains a
DivX video file.
The MP3 audio tracks and JPEG image
files start playing simultaneously.
, “MODE (MP3, JPEG)” is set to “AUTO”
(page 53).
The DivX video file cannot be played.
, The file is not created in DivX format.
, The file has an extension other than “.AVI”
or “.DIVX.”
, The DATA CD (DivX video)/DATA DVD
(DivX video) is not created in a DivX
format that conforms to ISO 9660 Level 1/
Level 2 or Joliet/UDF.
, The DivX video file is larger than 720
(width) × 576 (height).
Additional Information
, The disc is turned over.
Insert the disc with the playback side facing
down.
, The disc is skewed.
, The player cannot play certain discs
(page 6).
, The region code on the DVD does not match
the player.
, Moisture has condensed inside the player
(page 3).
, The player cannot play a recorded disc that
is not correctly finalized (page 6).
, The DATA CD/DATA DVD contains a
DivX video file.
The album/track/file names are not
displayed correctly.
, The player can only display numbers and
alphabet. Other characters are displayed as
“*”.
The disc does not start playing from the
beginning.
, Programme Play, Shuffle Play, Repeat Play,
or A-B Repeat Play is selected (page 29).
, Resume play has taken effect (page 26).
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
71
The player starts playing the disc
automatically.
, The disc features an auto playback function.
, “AUTO PLAY” in “CUSTOM SETUP” is
set to “ON” (page 66).
Playback stops automatically.
, While playing discs with an auto pause
signal, the player stops playback at the auto
pause signal.
Some functions such as Stop, Search, Fast
Play and Slow Play, Slow-motion Play,
Repeat Play, Shuffle Play, or Programme
Play cannot be performed.
, Depending on the disc, you may not be able
to do some of the operations above. Refer to
the operating manual that comes with the
disc.
The language for the sound track cannot
be changed.
, Try using the DVD’s menu instead of the
direct selection button on the remote
(page 27).
, Multilingual tracks are not recorded on the
DVD being played.
, The DVD prohibits the changing of the
language for the sound track.
The subtitle language cannot be changed
or turned off.
, Try using the DVD’s menu instead of the
direct selection button on the remote
(page 27).
, Multilingual subtitles are not recorded on
the DVD being played.
, The DVD prohibits the changing of
subtitles.
The player does not operate properly.
, When static electricity, etc., causes the
player to operate abnormally, unplug the
player.
5 numbers or letters are displayed on the
screen and on the front panel display.
, The self-diagnosis function was activated.
(See the table on page 73.)
The disc tray does not open and “LOCKED”
appears on the front panel display.
, Child Lock is set (page 25).
The disc tray does not open and “TRAY
LOCKED” appears on the front panel
display.
, Contact your Sony dealer or local
authorized Sony service facility.
“Data error” appears on the TV screen
when playing a DATA CD or DATA DVD.
, The MP3 audio track/JPEG image file/
DivX video file you want to play is broken.
, The data is not MPEG-1 Audio Layer III
data.
, The JPEG image file format does not
conform to DCF (page 49).
, The JPEG image file has the extension
“.JPG” or “.JPEG,” but is not in JPEG
format.
, The file you want to play has the extension
“.AVI” or “.DIVX,” but is not in DivX
format, or is in DivX format but does not
conform to a DivX Certified profile.
The angles cannot be changed.
, Try using the DVD’s menu instead of the
direct selection button on the remote
(page 27).
, Multi-angles are not recorded on the DVD
being played.
, The angle can only be changed when the
“
” indicator lights up on the front panel
display (page 9).
, The DVD prohibits changing of the angles.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
72
Self-diagnosis Function
(When letters/numbers appear in the
display)
When the self-diagnosis function is activated
to prevent the player from malfunctioning, a
five-character service number (e.g., C 13 50)
with a combination of a letter and four digits
appears on the screen and the front panel
display. In this case, check the following
table.
Glossary
Album (page 49, 51)
A unit in which to store JPEG image files or
MP3 audio tracks on a DATA CD/DATA
DVD. (“Album” is an exclusive definition for
this player.)
Chapter (page 9)
Sections of a picture or a music feature that
are smaller than titles. A title is composed of
several chapters. Depending on the disc, no
chapters may be recorded.
C:13:50
DivX® (page 56)
First three
characters of
the service
number
Cause and/or corrective
action
C 13
The disc is dirty or recorded
in a format that this player
cannot play (page 6).
, Clean the disc with a soft
cloth or check its format
(page 2).
C 31
The disc is not inserted
correctly.
, Re-insert the disc
correctly.
Digital video technology created by
DivXNetworks, Inc. Videos encoded with
DivX technology are among the highest
quality with a relatively small file size.
Dolby Digital (page 20, 68)
DTS (page 20, 69)
Digital audio compression technology that
Digital Theater Systems, Inc. developed. This
technology conforms to multi-channel
surround sound. The rear channel is stereo
and there is a discrete subwoofer channel in
this format. DTS provides the same discrete
channels of high quality digital audio.
Good channel separation is realized because
all of the channel data is recorded discretely
and little deterioration is realized because all
channel data processing is digital.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
Additional Information
E XX
To prevent a malfunction, the
(xx is a number) player has performed the
self-diagnosis function.
, Contact your nearest
Sony dealer or local
authorized Sony service
facility and give the 5character service number.
Example: E 61 10
Digital audio compression technology
developed by Dolby Laboratories. This
technology conforms to multi-channel
surround sound. The rear channel is stereo
and there is a discrete subwoofer channel in
this format. Dolby Digital provides the same
discrete channels of high quality digital audio
found in “Dolby Digital” theatre surround
sound systems. Good channel separation is
realized because all of the channel data is
recorded discretely and little deterioration is
realized because all channel data processing
is digital.
73
DVD VIDEO (page 5)
A disc that contains up to 8 hours of moving
pictures even though its diameter is the same
as a CD.
The data capacity of a single-layer and singlesided DVD is 4.7 GB (Giga Byte), which is 7
times that of a CD. The data capacity of a
double-layer and single-sided DVD is 8.5
GB, a single-layer and double-sided DVD is
9.4 GB, and double-layer and double-sided
DVD is 17 GB.
The picture data uses the MPEG 2 format, a
worldwide standard of digital compression
technology. The picture data is compressed to
about 1/40 (average) of its original size. The
DVD also uses a variable rate coding
technology that changes the data to be
allocated according to the status of the
picture. Audio information is recorded in a
multi-channel format, such as Dolby Digital,
allowing you to enjoy a more realistic audio
presence.
Furthermore, various advanced functions
such as the multi-angle, multilingual, and
Parental Control functions are provided with
the DVD.
DVD-RW (page 5)
A DVD-RW is a recordable and rewritable
disc that is the same size as a DVD VIDEO.
The DVD-RW has two different modes: VR
mode and Video mode. DVD-RWs created in
Video mode have the same format as a DVD
VIDEO, while discs created in VR (Video
Recording) mode allow the contents to be
programmed or edited.
DVD+RW (page 5)
A DVD+RW (plus RW) is a recordable and
rewritable disc. DVD+RWs use a recording
format that is comparable to the DVD VIDEO
format.
File (page 49, 52)
A JPEG image recorded on a DATA CD/
DATA DVD or a DivX video on a DATA
CD/DATA DVD (“File” is an exclusive
definition for this player). A single file
consist of a single image or video.
Film based software, Video based
software (page 18)
DVDs can be classified as Film based or
Video based software. Film based DVDs
contain the same images (24 frames per
second) that are shown at movie theatres.
Video based DVDs, such as television
dramas or sit-coms, displays images at 25
frames/60 fields (30 frames/60 fields) per
second.
MPEG audio (page 20, 68)
International standard coding system used to
compress audio digital signals authorized by
ISO/IEC. MPEG 1 conforms to up to 2channel stereo. MPEG 2, used on DVDs,
conforms to up to 7.1-channel surround.
Normal (Interlace) format (page 18)
Normal (Interlace) format shows every other
line of an image as a single “field” and is the
standard method for displaying images on
television. The even number field shows the
even numbered lines of an image, and the odd
numbered field shows the odd numbered lines
of an image.
Progressive format (page 17)
Compared to the Interlace format that
alternately shows every other line of an image
(field) to create one frame, the Progressive
format shows the entire image at once as a
single frame. This means that while the
Interlace format can show 25 or 30 frames
(50-60 fields) in one second, the Progressive
format can show 50-60 frames in one second.
The overall picture quality increases and still
images, text, and horizontal lines appear
sharper. This player is compatible with the
525 or 625 progressive format.
Progressive JPEG
Progressive JPEGs are used mostly on the
internet. They are different from other JPEGs
in that they “fade in” gradually instead of
being drawn from top to bottom when
displayed on a browser. This lets you view the
image while it is being downloaded.
Title (page 9)
The longest section of a picture or music
feature on a DVD, movie, etc., in video
software, or the entire album in audio
software.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
74
Specifications
System
General
Laser: Semiconductor laser
Signal format system: PAL/(NTSC)
Power requirements:
220 – 240 V AC, 50/60 Hz
Power consumption: 11 W
Dimensions (approx.):
430 × 43 × 237.3 mm
(width/height/depth) incl. projecting
parts
Mass (approx.): 1.95 kg
Operating temperature: 5 °C to 35 °C
Operating humidity: 25 % to 80 %
Audio characteristics
Frequency response: DVD VIDEO (PCM
96 kHz): 2 Hz to 44 kHz (±1.0 dB)/DVD
VIDEO (PCM 48 kHz): 2 Hz to 22 kHz
(±0.5 dB)/CD: 2 Hz to 20 kHz (±0.5 dB)
Signal-to-noise ratio (S/N ratio): 115 dB
(LINE OUT L/R (AUDIO) jacks only)
Harmonic distortion: 0.003 %
Dynamic range: DVD VIDEO: 103 dB/CD:
99 dB
Wow and flutter: Less than detected value
(±0.001% W PEAK)
Supplied accessories
See page 14.
Specifications and design are subject to
change without notice.
Outputs
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
Additional Information
(Jack name: Jack type/Output level/Load
impedance)
LINE OUT (AUDIO): Phono jack/2 Vrms/
10 kilohms
DIGITAL OUT (OPTICAL): Optical
output jack/–18 dBm (wave length
660 nm)
DIGITAL OUT (COAXIAL): Phono jack/
0.5 Vp-p/75 ohms
LINE OUT (VIDEO): Phono jack/1.0 Vp-p/
75 ohms
S VIDEO OUT: 4-pin mini DIN/Y:
1.0 Vp-p, C: 0.3 Vp-p (PAL), 0.286 Vp-p
(NTSC)/75 ohms
COMPONENT VIDEO OUT (Y, PB/CB,
PR/CR): Phono jack/Y: 1.0 Vp-p, PB/CB,
PR/ CR: 0.7 Vp-p/75 ohms
75
Language Code List
For details, see pages 41, 45, 64.
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027
1028
1032
1039
1044
1045
1051
1052
1053
1057
1059
1060
1061
1066
1183
1186
1194
1196
1203
1209
1217
1226
1229
1233
1235
1239
1245
1248
1253
1254
1257
1261
1269
1283
1287
1297
1298
1299
1300
1301
1305
1307
1311
1313
1326
1327
1332
1334
1347
1349
1350
1352
1353
1356
1357
1358
1363
1365
1369
1376
1379
1393
1403
1408
1417
1428
1435
1507
1508
1509
1511
1512
1513
1514
1515
1516
1517
1521
1525
1527
1528
1529
1531
1532
1534
1535
1538
1539
1540
1543
1557
1564
1572
1581
1587
1613
1632
1665
1684
1697
1067
1070
1079
1093
1097
1103
1105
1109
1130
1142
1144
1145
1149
1150
1151
1157
1165
1166
1171
1174
1181
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali;
Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
German
Bhutani
Greek
English
Esperanto
Spanish
Estonian
Basque
Persian
Finnish
Fiji
Faroese
French
Frisian
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Italian
Hebrew
Japanese
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian;
Lettish
1345 Malagasy
1436
1463
1481
1482
1483
1489
1491
1495
1498
1501
1502
1503
1505
1506
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
(Afan)Oromo
Oriya
Punjabi
Polish
Pashto;
Pushto
Portuguese
Quechua
RhaetoRomance
Kirundi
Romanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
SerboCroatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Chinese
Zulu
1703 Not specified
Parental Control Area Code List
For details, see page 60.
Code Area
Code Area
Code Area
Code Area
2044
2047
2046
2057
2070
2079
2090
2092
2115
2165
2174
2109
2248
2238
2254
2276
2304
2363
2362
2376
2390
2379
2427
2424
2436
2489
2501
2149
2499
2086
2528
2184
Argentina
Australia
Austria
Belgium
Brazil
Canada
Chile
China
Denmark
Finland
France
Germany
India
Indonesia
Italy
Japan
Korea
Malaysia
Mexico
Netherlands
New Zealand
Norway
Pakistan
Philippines
Portugal
Russia
Singapore
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
76
Spain
Sweden
Switzerland
Thailand
United
Kingdom
Index
Numerics
16:9 65
4:3 LETTER BOX 65
4:3 OUTPUT 66
4:3 PAN SCAN 65
48kHz/96kHz PCM 69
5.1 Channel Surround 42
A
A-B REPEAT 32
ADVANCE 25
ALBUM 35
Album 49, 73
ANGLE 45
AUDIO 41, 64
AUDIO ATT 67
AUDIO DRC 67
AUDIO SETUP 67
AUTO PLAY 66
AUTO POWER OFF 66
B
BACKGROUND 65
Batteries 14
C
D
DATA CD 5, 49, 56
DATA DVD 5, 56
DATE 52
DIGITAL OUT 68
Digital output 68
DIMMER 66
Display
Control Menu Display 11
Front panel display 9
Setup Display 63
DivX® 56, 67
DOLBY DIGITAL 41, 68, 73
DOWNMIX 68
DTS 41, 69, 73
DVD 5, 24, 74
DVD+RW 25, 74
E
EFFECT 55
F
Fast forward 33
FAST PLAY 25
Fast reverse 33
FILE 35
File 74
Film based software 74
Freeze Frame 34
Front panel display 9
H
Handling discs 2
Hooking up 14
I
INDEX 34
Interlace format 74
INTERVAL 54
J
JPEG 49
L
LANGUAGE SETUP 64
LINE 65
Locating
a specific point by watching
the TV screen 33
M
MEMORY 47
MENU 64
MODE (MP3, JPEG) 53
MP3 5, 49
MPEG 41, 68, 74
MULTI-DISC RESUME 26,
67
N
NORMAL (INTERLACE) 17
Normal (Interlace) format 74
O
On-screen display
Control Menu Display 11
Setup Display 63
ORIGINAL 27
ORIGINAL/PLAY LIST 27
OSD 64
P
PARENTAL CONTROL 59
PAUSE MODE 67
PBC Playback 28
PICTURE NAVIGATION 36,
52
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
PLAY LIST 27
PROGRAMME 29
Programme Play 29
PROGRESSIVE AUTO 17
Progressive format 74
PROGRESSIVE VIDEO 17
Q
QUICK 64
Quick Setup 21, 64
R
Remote 10, 14, 62
REPEAT 31
Repeat Play 31
Replay 25
RESET 64
Resume 26
S
Scan 33
SCENE 34
SCREEN SAVER 65
SCREEN SETUP 65
Searching 33
SETUP 63
Setup Display 63
SHARPNESS 48
SHUFFLE 30
Shuffle Play 30
Slide Show 53
SLOW PLAY 25
Slow-motion Play 34
Speakers
Hooking up 19
SUBTITLE 64
SURROUND 43
T
TIME/TEXT 34, 37
TITLE 34
Title 74
TITLE VIEWER 36
TOP MENU 27
TRACK 34
TRACK SELECTION 67
Troubleshooting 70
TV TYPE 65
TVS (TV Virtual Surround) 43
Additional Information
CD 6, 24
CHAPTER 34
Chapter 73
CHAPTER VIEWER 36
Child Lock 25
Connecting 15
Continuous play
CD/VIDEO CD 24
DVD 24
Control Menu 11
CUSTOM 63
CUSTOM PARENTAL
CONTROL 59
CUSTOM PICTURE MODE
46
CUSTOM SETUP 66
DVD’s menu 27
DVD-RW 5, 27, 74
U
Usable discs 6
V
Video based software 74
VIDEO CD 5, 24
Z
ZOOM 25, 52
77
Printed on 100% recycled paper.
Sony Corporation
Printed in HungarySherwood Manuals
Downloaded
From DvDPlayer-Manual.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement