DigiWeight DWP-5500R User manual

DigiWeight DWP-5500R User manual
DWP-5500FP (4’x4’)
DWP-11KRFP (5’X5’)
Weighing Indicator
User Manual
●
●
Please read the user manual carefully before using
Please keep the user manual properly for future reference
Content
CHAPTER 1 MAIN SPECIFICATION
CHAPTER 2 INSTALLATION
CHAPTER 3 INDICATOR
2
Chapter 1 Main Specification
1. Model: DWP-F SERIES NTEP Floor / Pallet scale
2. Accuracy: GradeⅢ, n=5000
3. Sample Rate: 10 times/second
4. Load cell sensitivity 1.5~3mV / V
5. Scale interval: 1/2/5/10/20/50 for option
6. Display: 6 bits LED, 8 state indicating signals
7. Power supply: AC100V~230V,50~60HZ
8. Operating temperature/humidity: 0~50℃; ≤90%RH
9. Transporting temperature: -20~60℃
Chapter 2 Installation
2.0 SCALE BASE SETUP
a. Open the scale base box (Box 1) with a knife very carefully. Sharp blade may
scratch the scale surface.
2
b. Take out the scale feet (total 4 feet packed in the box inside the scale base)
c. Screw each foot ontothe load cell at each corner of the scale base.
3
d. Take out the indicator from Box 2. Plug the scale serial cable into the socket on the back of the
indicator. And use a screw driver to tighten the two screws of the plug.
Turn on the indicator by pressing the ON/OFF button on the front of the indicator.
Now your scale is ready to use. For advanced operations, please refer to the following pages.
CHAPTER 3 INDICATOR
▲ The connection between load cell and indicator must be reliable. The shield cable of load cell must be
grounded firmly.
▲ Do not plug or unplug the connection wire while the indicator is powered up to avoid damages to indicator or
load cell by static electricity.
▲ Indicator and load cell are static sensitive device and anti-static measures must be adopted in use.
▲ In the thunderstorm season, a reliable lighting protection measure must be installed to avoid
damage of indicator or load cell by lightning. Make sure the safety of operator and the safe
operation of weighing equipment and associated equipment.
▲ Do not use in the place where there is inflammable gas or vapor. Do not use in the pressure hopper system.
▲ Keep the indicator and load cell away from high electric field, magnetic field, strongly corrosion object and
flammable object.
▲ Do not clean the housing with strong solvent (such as benzol and nitro oil).
▲ Do not inject liquid or conduction grain into the indicator to avoid damage to indicator or electric shock.
▲ Do not open the lead sealing without authority from department of electrical supervision. Calibration can
not be done without breaking the lead sealing.
☆ Rechargeable battery is consumable and is not covered by guarantee.
☆ To prolong the life of use of rechargeable battery, be sure to use after it is fully charged.
☆ If the indicator won’t be used for long time, it is must be recharged once in 2 months and charged for 20
hours each time.
☆ Be carefully while moving or installing to avoid strong shaking or impact, to prevent short circuit or damage
to rechargeable battery.
◆The indicator should be placed flatly and not be in the straight sunshine for clear indication and long-term
service life.
◆The indicator should not be placed in a vibrating area full of dust, and not in a sloppy environment.
◆Before connecting or disconnecting indicator and peripheral equipment, powder supply of the indicator and
other devices should be firstly switched off!
◆Regulations about external connection in the manual should be strictly observed. It is not allowed change
the connection at random.
◆It is not allowed to open the indicator, otherwise we do not guarantee to repair. There is high voltage inside
the indicator. Non-professional people are not allowed to repair to avoid more serious damage to system and
human or accident.
◆If not man-made trouble happens within one year after the date of sale , the indicator is under regular
service condition, please send the troubled indicator and guarantee card (the serial number should be
coincident) to the special repair shop or the supplier.
◆ While it is over guarantee time, man-made trouble or other accidental damage, the manufacturer will
repair with charge.
Printed version might be slightly different from product because of the improvement of product
function. Please contact the manufacturer from latest version.
The right of revising this manual is preserved.
1)Technical parameters
≥1.5uV/e
Δ-Σ technique,20bit


Input Sensitivity:
A/D Conversion:

Supply bridge Voltage of load cell: DC 5V, can connect 1-4 pcs of 350Ω strain gauge load cells;




Connection with load cell:use 4 wires
Division value:
1/2/5/10/20/50/100 optional
Display:
6 bits LCD display
Clock display: Display the year/month/day, hour/minute/second, automatic leap year, leap month. No need to
reset after power off.
Character setting: Chinese/English is available for printing
Scoreboard interface: current loop serial output method, 600bps
Printer interface: Inner thermal micro-printing,57mm width paper, diameter of the paper reel≤40mm
Power supply : AC110~220V , 50~60Hz, can external connect DC 6V/7Ah free maintenance lead-acid
battery(optional).
Size of the indicator:
240*173*187mm(long*wide*height)
Weight of the indicator: about 1.15 (kg)
Operation environment: Operating temperature: 0℃~40℃
Operating Humidity:≤85%(RH),No condensation
Storage environment::storage temperature: -10℃~50℃
Storage Humidity:≤95%(RH),No condensation








2)Installation
2.1 Indicator Diagram Sketch
Front board
Back board
Remark:The 9 hole interface at back is for connection with load cell,9 pin interface is for scoreboard
connection.
2.2 Screen of the Indicator
Zero
%:Sum
Stable
OZ:Inner code
N.W.
kg:kilogramme
Animal status
Battery condition
2.3 Connection with Load cell
Animal
weighing
stable
location
①
Description
description
Load cell negative
excitation
code
E-
②
Load cell negative
feedback
F-
⑥
Load cell
excitation
positive
E+
⑦
Load cell
feedback
positive
⑧
Load cell signal input
-
S-
⑨
Load cell signal input
+
S+
⑤
Shield cable
F+
SHIELD
This indicator is connecting with 4 wires cable, user must make the short circuit for positive excitation and
positive feedback、negative excitation and negative feedback
▲!The connection of load cell and indicator should be relible. The shield wire of load cell must be connected to
the earth. It is not allowed to connect or disconnect with power supply. Avoid damage to indicator or load cell by
static electricity.
▲ !Load cell and indicator are static sensitive devices, so static-proof measures should be adopted.
2.4 The connection with scoreboard
Scoreboard
Communications
Scoreboard mating plug
DB9 core terminals
③
⑨
⑤
⑤
▲!The connection between scoreboard and indicator scoreboard output must be correct, if with wrong
connection, it will cause damage to output interface of indicator or input interface of scoreboard .Even it will
damage seriously indicator and scoreboard . Special connection cable shall be used. The scoreboard will
display nothing when the indicator is under calibration status.
3) Operation
3.1 Startup and startup Auto-Setting Zero
1、Power on and turn on the power switch, the indicator will have self-inspection .Then it will enter weighing
status directly.
2、when startup, if the displayed data is not zero, but still in setting range, the indicator will set zero
automatically. Startup zero setting rand and method is refer to the calibration chapter
During normal working, the calibration switch should be on forbidding position (down place)
3.2 Manual zero setting (semi-automatic)
1、 When the displayed data is not zero, but still in the range of setting, the key【ZERO】can be operated.
Otherwise, it is not available. Zero setting parameter selection and setting is refer to the calibration chapter.
2、 Zero setting is available only when the stable indication is light.
3.3 Tare
1、Under weighing status and with stable platform, indicator can do tare operations continuously.
2、When it conform to zero setting conditions, press 【ZERO】to set tare as zero. The light of net weight will be
off.
3.4 Operations of animal scale function
Step
1
Operations
Display
Press[SET]
Press[0]
Press[ENTER]
[******]
Note
Under weighing status
Under animal scale weighing status, press [WEIGHING] to
exit
2
3.5 ISN code operations
Step
1
Operations
Display
Press[SET]
Press[2]
Press[ENTER]
[******]
Note
Under weighing status
2
Under ISN code status, press [WEIGHING] to exit
3.6 Setting for backlight、language and printing sn
Step
Operations
Display
Note
1
Press[SET]
Press[1]
Press[ENTER]
[US
2
Press[000]
Press[ENTER]
[ST XYZ]
[ST 000]
3
]
Under weighing status
Note: Auto-zero setting after setting Z value,refer to note
1
Default setting in Factory:000
Weighing status
Note1:special statement, for english verison indicator, Y value is always 1.
Input value
0
1
Auto-backlight
Backlight off
X:screen backlight
chinese
english
Y:print language
Not clear
clear
Z:clear printing serial no.
When accumulation symbol ”%” is on ,print accumulated weight value.
2
Backlight on
——
——
3.7 Printing
1) No tare printing
step
1
2
3
description
Load goods
stable
Printing
finished
operations
Press[PRINT]
is
display
[******]
[ Print ]
[******]
note
Showing current weight
Print current data
Return to weigh after printing
display
[******]
[
0]
note
Showing current weight
Showing N.W.=0
[******]
Showing current weight
2)Tare printing
step
1
2
description
Load tare
stable
Press [TARE]
3
stable
Load goods
4
stable
Printing
finished
Press[PRINT]
5
operations
is
[ Print ]
[******]
Print current data
Return to weigh after printing
3) Accumulation printing
When accumulation symbol ”%” is on ,the printed data is accumulated weight value. Press [CLEAR],
accumulation symbol ”%” is off, the accumulated data is clear up.
4) Complementary printing
Press [REPRINT] to print the latest record.
Note: If the power shows 1 grid, please print after charging up or connecting with AC power supply in time. If
the weight is smaller than 5 intervals value, it can not printing.
3.8 Accumulation function
1、Sum operation. Under weighing status, to press[Σ] after platform is stable ,then the indicator will display
times of accumulation and total weight, then return to weighing status. It can start to sum again only after
the scale returns to zero.
2、Clear up of the summary data. Under weighing status, to press [CLEAR] to clear up records of sum times
and total weight.
3、Checking summary data. Under weighing status, to press [Σ] when the indicator displays zero. The
indicator will show summary times first and total weight, then return to weighing status .
Note:The summary data can not be saved after power off ,during summing status, the light of ”%” is
on .
3.9 Date and time setting
1、Under weighing status, press[Date] then the indicator will display current date. If correct, then press
[ENTER] or [WEIGHING] to exit .If not correct, input numbers and press [ENTER]
2、Under weighing status , press[TIME] then the indicator will display current time and run automatically. If
correct, then press [WEIGHING] to exit .If not correct, input numbers and press [ENTER].
3.10 Use of storage battery(Storage battery is extra requirement )
1、With storage battery and AC power supply connected, if not able to start up the indicator, it maybe in
condition of lower power supply . Please wait to charge the battery or operate with AC power after unloading
the battery.
2、The red connects to the positive pole of stock battery ,the black connects to negative pole .Please
note!( the connection line of storage battery is optional)
3、If only with storage battery, there is a signal on the display of indicator showing the battery condition. With
full lights on, it means enough power .If only lower one is light, please charge up in time.
4、Please charge up the battery completely at first time .If without use for long time, we suggest to charge the
battery each 2 months for 20hours.Move the devices slightly in order to avoid strong shock and impact which
easily causes short circuit inside of the battery, and destroy the battery.
Specially warning: If without confirmation from technology monitoring department, please do not break the
seal on the product, can not calibrate without breaking the seal .
4 Information prompt
4.1 Normal information prompt
Display
Note
Print
Please wait, data are transmitting between indicator and printer
Lbat
Power is too low to print ,please charge up.
4.2 Error prompt
Display
Note
Err 01
Error on automatic zero-setting or by hand
Err 02
Error on summary
Err 03
overloading
Err 06
Error on tare operations
Err 16
Error on date and time setting
Err 22
Error on clock cores
Err 19
Not able to print when zero, minus weight or not stable weight
Err P
Error on printer
Err 18
Error on parameter setting
Err 09
Error on inspection of calibration data
Annex 1: Function of charging
It is available to charge up with DC currency, please use 6V/7Ah for storage battery. Interface
connection is negative for outside and positive for inside.
If the battery is with opposite connection, it will make damage to the indicators .Please note.
This product is not provided with storage battery, if you need, please order additionally.
Note: 1.We do not guarantee damage to the battery itself with wrong connection.
2.When charging up, if fail to start up the indicator maybe for lower power, please try again after
charging.
Annex 2: Print form Indicator
Weight list
--------------------------------------------Item:
0001
Date:
10-06-06
Time:
06:06:06
G.W.:
8000(kg)
Tare weight: 1300(kg)
N.W.:
6700(kg)
---------------------------------------------Weighing Bill
----------------------------------------------S.N.:
0001
Date:
10-06-06
Time:
06:06:06
GW:
8000(kg)
TW:
1300(kg)
NW:
6700(kg)
------------------------------------------------
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement