Model AM2
Model AM2
➤Owner’s
Guide
limited lifetime consumer warranty
Directed Electronics, Inc. promises to the original purchaser to repair or replace with a
comparable reconditioned model any Directed Electronics, Inc. unit (hereafter the
"unit"), excluding without limitation the siren, the remote transmitters, the associated
sensors and accessories, which proves to be defective in workmanship or material under
reasonable use during the lifetime of the vehicle provided the following conditions are
met: the unit was professionally installed and serviced by an authorized Directed
Electronics dealer; the unit will be professionally reinstalled in the vehicle in which it was
originally installed by an authorized Directed Electronics dealer; and the unit is returned
to Directed Electronics, Inc., shipping prepaid with a legible copy of the bill of sale or
other dated proof of purchase bearing the following information: consumer's name, telephone number and address; the authorized dealers name, telephone number and address;
complete product description, including accessories; the year, make and model of the
vehicle; vehicle license number and vehicle identification number. All components other
than the unit, including without limitation the siren, the remote transmitters and the
associated sensors and accessories, carry a one-year warranty from the date of purchase of
the same. This warranty is non-transferable and is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten (10) days of the date
of purchase to the address listed on the card; the unit's date code or serial number is
defaced, missing or altered; the unit has been modified or used in a manner contrary to
its intended purpose; the unit has been damaged by accident, unreasonable use, neglect,
improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installation or
removal of the unit. Directed Electronics, Inc., in its sole discretion, will determine what
constitutes excessive damage and may refuse the return of any unit with excessive damage.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES,
INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR
PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL
PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED ELECTRONICS,
INC. NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO
ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION
WITH ITS PRODUCTS. DIRECTED ELECTRONICS, INC. DISCLAIMS AND
HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED
ELECTRONICS, INC. SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE
DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED ELECTRONICS, INC.
IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM,
DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS;
AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER,
INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE
© 2003 directed electronics, inc.
i
AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS
FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR
ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A
CLAIM OR A DISPUTE INVOLVING DIRECTED ELECTRONICS, INC. OR ITS
SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE
STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM
RECOVERY UNDER ANY CLAIM AGAINST DIRECTED ELECTRONICS, INC.
SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED ELECTRONICS DEALER'S PURCHASE PRICE OF THE UNIT. DIRECTED ELECTRONICS, INC. SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL
DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME,
LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE
CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations
on how long an implied warranty will last or the exclusion or limitation of incidental or
consequential damages. This warranty gives you specific legal rights and you may also have
other rights that vary from State to State.
This product may be covered by a Guaranteed Protection Plan ("GPP"). See your
authorized Directed Electronics dealer for details of the plan or call Directed
Electronics, Inc. Customer Service at 1-800-876-0800. Directed Electronics, Inc. security systems, including this unit, are deterrents against possible theft. Directed
Electronics, Inc. is not offering a guarantee or insurance against vandalism, damage or
theft of the automobile, its parts or contents; and hereby expressly disclaims any
liability whatsoever, including without limitation, liability for theft, damage and/or
vandalism. Directed Electronics, Inc. does not and has not authorized any person or
entity to create for it any other obligation, promise, duty or obligation in connection
with this security system.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt, showing the following:
➤
➤
➤
➤
➤
➤
➤
➤
➤
ii
Date of purchase
Your full name and address
Authorized dealer's company name and address
Type of alarm installed
Year, make, model and color of the automobile
Automobile license number
Vehicle identification number
All security options installed on automobile
Installation receipts
© 2003 directed electronics, inc.
table of contents
limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
transmitter (standard) configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
transmitter functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
what is included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
system maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
your warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
fcc/id notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
transmitter functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
standard configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
using your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
locking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
disabling the system without a transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
silent modeTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
valet® mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
owner recognitionTM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
rapid resume logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
programming options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
security & convenience expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
© 2003 directed electronics, inc.
1
transmitter (standard) configuration
lock
auxiliary output
unlock
panic
insert coin at this
edge to open
transmitter case
To access the battery, use a coin to at the bottom of the transmitter to open the case.
transmitter functions
controls the Lock function.
controls the Unlock function.
controls Silent Mode™ and an Auxiliary Output.
controls the Panic function.
2
© 2003 directed electronics, inc.
and
pressed together control an additional
Auxiliary Output.
what is included
➤
The control module
➤
2 four-button transmitters
➤
Pre-wired Valet® switch with integrated Red status led
➤
Your warranty registration
➤
Failsafe® Starter Kill Relay
important information
Congratulations on the purchase of your keyless entry system.
Due to the complexity of this system, it must be installed by an
authorized dealer only. Installation of this product by anyone
other than an authorized dealer voids the warranty. All dealers
are provided with a preprinted dealer certificate to verify that
they are authorized.
By carefully reading this Owner's Guide prior to using your
system, you will maximize the use of this system and its features.
You can print additional or replacement copies of this manual by
accessing the Directed web site at www.directed.com.
© 2003 directed electronics, inc.
3
➜ system maintenance
The system requires no specific maintenance. Your remote is
powered by a small, lightweight 3-volt lithium battery (CR2032)
that will last approximately one year under normal use. When
the battery begins to weaken, operating range will be reduced
and the LED on the remote will dim. Refer to Transmitter
(Standard) Configuration for battery access.
➜ your warranty
Your warranty registration must be completely filled out and
returned within 10 days of purchase. Your product warranty
will not be validated if your warranty registration is not returned.
Make sure you receive the warranty registration from your dealer.
It is also necessary to keep your proof of purchase, which reflects
that the product was installed by an authorized dealer.
➜ fcc/id notice
This device complies with Part 15 of FCC rules. Operation is
subject to the following conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesirable operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate this device.
4
© 2003 directed electronics, inc.
Directed Electronics, Inc.
416 Series
Tested to Comply
with FCC Standards
DRW-371
transmitter functions
The receiver uses a computer-based learn routine to learn the
transmitter buttons. This makes it possible to assign any specific
transmitter button, or combination of buttons, to any receiver
function. The transmitter initially comes programmed with the
Standard Configuration, but may also be customized by an
authorized dealer. The transmitter buttons indicated in all of the
instructions in this manual correspond to a Standard
Configuration transmitter.
➜ standard configuration
Button
The locking function is controlled by pressing this button for one
second.
Button
The unlocking function is controlled by pressing this button for
one second.
© 2003 directed electronics, inc.
5
Button
Silent Mode™ and an optional auxiliary function are controlled
by this button. (An optional auxiliary function, such as trunk
release, can be controlled by pressing this button for 2 seconds.)
The auxiliary output controls __________________________.
Button
The panic feature is controlled by pressing this button for one
second.
and
Buttons
An optional auxiliary convenience or expansion function that
you have added to your system can be activated by pressing these
buttons simultaneously.
The auxiliary output controls_________________________.
using your system
➜ locking
Pressing
for one second locks the system by activating the
starter kill and locking the doors (if connected). The horn will
honk (if connected) and the parking lights will flash once to
confirm locking of the system. While the system is locked, the
status LED will flash once per second. The Failsafe® Starter Kill
(if installed) will also prevent the vehicle’s starter from cranking.
6
© 2003 directed electronics, inc.
note: Manually locking the vehicle does not arm the system; it will only lock the doors.
The system can also be programmed to arm the optional Failsafe®
Starter Kill automatically (called Passive Mode). If the system has
been programmed for Passive Mode, the Failsafe® Starter Kill will
automatically activate 30 seconds after the ignition has been
turned off. After the ignition has been turned off, the status LED
will flash rapidly to indicate that the system is in Passive Mode.
If Passive Mode has been programmed on, then it is also possible
to program the system for Passive Locking. With Passive Locking,
the vehicle doors lock automatically at the same time that the Failsafe®
Starter Kill is activated. If Passive Locking is programmed on, care
must be taken to prevent the keys from being locked in the vehicle.
note: For Passive Mode to be effective, the Failsafe®
Starter Kill relay must be installed.
➜ unlocking
Pressing
for one second unlocks the system and the doors (if
connected). The horn will honk twice (if connected) and the
parking lights will flash twice to confirm unlocking of the system.
The optional Failsafe® Starter Kill will be deactivated. The status
LED will turn off, unless the system is programmed for Passive
Mode. In Passive Mode, the status LED will flash rapidly when the
system is unlocked. This indicates that the system will re-engage
the starter kill and re-lock the doors (if Passive Locking has been
© 2003 directed electronics, inc.
7
programmed) in 30 seconds unless the ignition is turned on.
note: If the system has been locked with the remote
transmitter, you must use the transmitter or the Valet®
switch to unlock the system and deactivate the starter kill.
Manually unlocking the vehicle does not unlock the system; it will only unlock the doors.
➜ disabling the system without a transmitter
If your remote transmitter is lost or damaged, you can manually
override the system. To do this, you must have the vehicle's ignition key and know where the integrated LED/Valet® switch is
located. Be sure to check with the installer for the location of the
integrated LED/Valet® switch.
Integrated
LED/Valet® switch
8
© 2003 directed electronics, inc.
To unlock the security system,
turn the ignition to the ON position. Press and release the integrated LED/Valet® switch within
DRW-35
10 seconds. The status LED will
stop flashing and the vehicle
should start. If the vehicle does
not start, you may have waited
too long; turn the ignition off and
repeat the process.
Location of integrated LED/Valet® Switch______________________
➜ silent modeTM
To temporarily turn off the lock or unlock chirps, (if the horn is
hooked up) use Silent Mode™. Simply press
for less than
one second before locking or unlocking, and the confirmation
chirp(s) will be eliminated for that one operation only. If you
want the lock/unlock chirps turned off permanently, your dealer
can do this for you.
➜ valet mode
®
You can prevent your system from automatically activating the
Failsafe® Starter Kill and locking the doors by using Valet® Mode.
This is very useful when washing the vehicle or having it
serviced. In Valet® Mode, the starter kill cannot be activated,
even with the transmitter, but all convenience functions (door
locks, trunk release, etc.) will continue to work normally.
© 2003 directed electronics, inc.
9
To enter or exit Valet® Mode:
1. Turn the ignition on.
2.
Turn the ignition off.
3.
Press and release the inte-grated LED/Valet® switch
DRW-35
within 10 seconds.
The status LED lights continuously if you are entering Valet®
Mode and turns off if you are exiting Valet® Mode.
➜ panic mode
If you are threatened in or near your vehicle, you can attract
attention by triggering the system with your transmitter. Just
press
for two seconds to enter Panic Mode. In Panic Mode,
the horn will honk and the parking lights will flash for 30
seconds. To stop Panic Mode at any time, press
on the
transmitter again.
note: In order for Panic Mode to be effective, the vehicle’s
horn (or optional siren) as well as the vehicle's parking
lights must be connected.
10
© 2003 directed electronics, inc.
owner recognitionTM
Owner Recognition® is a feature available exclusively from
Directed. Using the Directed Bitwriter®, a hand-held programming
tool, your dealer can program many of the system settings. The
programmer makes it possible to program different settings for
each transmitter that is used with the system. Then, whenever a
specific transmitter is used, the system will recall the settings
assigned to that transmitter. Owner Recognition lets up to four
users of the system have different settings that meet their specific
needs. It is almost like having four separate alarms in your vehicle,
one for each user.
note: Owner Recognition cannot be programmed without a Directed Bitwriter® and the necessary software.
Check with your dealer for more information.
rapid resume logic
This Directed system will store its current state to non-volatile
memory. If power is lost and then reconnected, the system will
recall the stored state from memory. This means if the unit is in
Valet® Mode and the battery is disconnected for any reason, such
as servicing the car, when the battery is reconnected the unit will
still be in Valet® Mode. This applies to all states of the system
including lock, unlock, and panic mode.
© 2003 directed electronics, inc.
11
programming options
Programming options control your system's normal, operational
set-up. Most options do not require additional parts, but some may
require additional installation labor. This system's programming
options are listed below, with the factory default settings in bold:
➤
Passive Mode or Active Mode. In Passive Mode the Failsafe®
Starter Kill will automatically activate 30 seconds after the
ignition has been turned off.
➤
Ignition switch-controlled door-locking on or off. With this
feature on, the doors will lock 3 seconds after the ignition
key is turned on, and unlock when the ignition key is turned
off.
➤
Passive Locking or Active Locking (doors lock only with the
transmitter). With Passive Locking, the vehicle doors lock
automatically 30 seconds after the ignition has been turned
off. Passive Locking can only be selected when the system
has been programmed for Passive Mode.
➤
The horn honk confirmations for locking and unlocking can
be programmed on or off. In order for this feature to work
properly, the horn must be connected to the system.
➤
Domelight supervision when the key is turned off can be programmed on or off. If programmed on, the domelight will
turn on for 30 seconds each time the ignition is turned off.
12
© 2003 directed electronics, inc.
glossary of terms
Control Unit: The “brain” of your system. Usually hidden under
the dash area of the vehicle. It houses the microprocessor that
monitors your vehicle and controls all system functions.
Integrated LED/Valet® Switch: A small push-button switch with an
integrated Red LED mounted somewhere in the vehicle. The
switch is used to override the alarm when a transmitter is lost or
damaged, or to put it into Valet® Mode. The LED indicates the
status of your system. It is also used to report triggers and faults
in the system or sensors. This switch is also used to program
optional features.
Starter Interrupt: An automatic switch controlled by your system
which prevents the vehicle’s starter from cranking whenever the
system is locked. The vehicle is never prevented from cranking
when the system is unlocked, in Valet® Mode, or if the starter
interrupt switch itself fails. Your system has feature-ready
circuitry for the starter interrupt, however installation may
require additional labor.
Transmitter: A hand-held, remote control which operates the
various functions of your system.
© 2003 directed electronics, inc.
13
security & convenience expansions
Listed below are some of the many expansion options available
for use with your system. Some options may require additional
parts and/or labor. Please consult with your dealer for a complete
list of options available for use with this system.
Domelight Supervision: The domelight will illuminate for 30
seconds each time the system is unlocked using the remote. This
is useful for seeing inside the vehicle at night prior to entering.
Power Door Lock Control: Your system is capable of controlling
many types of power door lock systems; however, some door
lock systems may require extra parts. Consult with your dealer to
determine which type of locks your vehicle uses. If power locks
are connected, the system can be programmed to lock the doors
automatically 30 seconds after the ignition has been turned off.
The system can also be programmed to lock the doors when the
ignition is turned on and to unlock them when the ignition is
turned off.
Power Trunk Release: The system’s auxiliary output can be
programmed to operate a factory power release for the vehicle's
trunk or hatch. If the factory release is not power-activated,
Directed®'s 522T trunk-release solenoid can often be added.
Power Window Control: Power window control is provided with
Directed®'s 529T or 530T systems. The 529T system will roll up
two windows automatically when the system is locked, or roll
two windows down by using the transmitter. The 530T will roll
14
© 2003 directed electronics, inc.
two windows both up and down. The 530T also provides one
touch switch operation.
Progressive Door Unlocking: For added security, your system can
be configured to unlock the driver’s door only, leaving the
passenger doors locked. Pressing the unlock button an additional
time will unlock the passenger doors. This option requires additional parts and labor.
© 2003 directed electronics, inc.
15
16
© 2003 directed electronics, inc.
✂
Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet.
✂
QUICK REFERENCE GUIDE
To lock using your remote
➤
To lock the system press
for one second. The doors lock (if connected).
The LED will begin to flash. The Failsafe® Starter Kill (if installed) prevents
the vehicle’s starter from cranking. To confirm system locking the vehicle’s
horn (if connected) honks once and the parking lights flash once.
To unlock using your remote
➤
To unlock the system press
for one second. The doors will unlock (if
connected). The Failsafe® Starter Kill deactivates. To confirm unlocking the
vehicle’s horn (if connected) honks twice and the parking lights flash twice.
Disabling the Failsafe® Starter Kill without a transmitter
➤
Turn on the ignition. Press and release the integrated LED/Valet® switch
within 10 seconds. The LED will stop flashing and the vehicle can be started.
To enter or exit Valet® Mode
➤
1. Turn the ignition to the ON position.
2. Turn the ignition back OFF.
3. Within 10 seconds press and release the integrated LED/Valet® switch.
The status LED lights continuously if you have entered Valet® Mode. To
exit Valet® Mode, repeat steps 1–3. The LED turns off when exiting Valet®
Mode.
To activate Panic Mode
➤
Press and hold
for 2 seconds.
To exit Panic Mode
➤
Press
on the transmitter.
Location of integrated LED/Valet® Switch______________________
The company behind this system is Directed Electronics, Inc.
Since its inception, Directed Electronics has had one purpose, to provide consumers with
the finest vehicle security and car stereo products and accessories available. The recipient of
nearly 100 patents and Innovations Awards in the field of advanced electronic
technology, DIRECTED is ISO 9001 registered.
Quality Directed Electronics products are sold and serviced throughout North America
and around the world.
Call (800) 274-0200 for more information about our products and services.
Directed Electronics is committed to delivering world class quality products
and services that excite and delight our customers.
Directed Electronics, Inc.
Vista, CA 92081
www.directed.com
© 2003 Directed Electronics, Inc. - All rights reserved
G416A 9-03
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement